VOLUME IIIengineeringprojects.com/Tender/UploadFiles/3435_Vol-III.pdf · 2018. 7. 27. · 25 5.40.1...

AN ISO 9001 & 14001 COMPANY

TENDER DOCUMENT

TENDER No: DLI/CON/759/590

FOR

Construction of 100 bedded Hospital at Bhilai, Chhattisgarh for Employees State Insurance Corporation (ESIC).

VOLUME – III

Quoting sheet & BOQ

AMOUNT IN Rs. AFTER ADDING %

(-) BELOW / AT PAR / (+) ABOVE

1 2 3 5 = (4 x 3)

In figures In words In figures

1Construction of 100 Bedded Hospital for

ESIC at Bhilai 672505366

4

Total

Note:

Rates to be quoted in this tender all inclusive with all taxes and duties etc. including GST.

BIDDERS FINANCIAL OFFER:

(In Figures)______________________________________________________________________________________________________________________________

(In Words)_______________________________________________________________________________________________________________________________

ENGINEERING PROJECTS (INDIA) LTD.

(A GOVERNMENT OF INDIA ENTERPRISE)

QUOTING SHEET FOR BIDDERS

Name of work - Tender for Construction of 100 Bedded Hospital for ESIC at Bhilai

NIT No. DLI/CON/759/590 dated 08.12.2017

SI. No. Name of work

ESTIMATED

COST (Rs.)

Without Taxes

TO BE QUOTED BY TENDERER

% (-) BELOW/ AT PAR/(+) ABOVE

Sign and Stamp of EPIL 200 Sign and Stamp of Bidder

SL. No. Description of Item Amounts

1 CIVIL

⁼

420292880.49

2 HVAC

⁼

30243129.00

3 MEP

⁼

6860014.00

4 FURNITURE

⁼

11818620.00

5 OPERATION THEATRE

⁼

23444706.00

6 TRACK SYSTEM

⁼

11040000.00

7 KITCHEN EQUIPMENT

⁼

5728750.00

8 LAUNDRY

⁼

3079155.00

9 MEDICAL GAS

⁼

16033000.00

10 SIGNAGE

⁼

3654353.00

11 TSSU EQUIPMENT

⁼

4051079.00

12 ELECTRICAL

⁼

79098580.87

13 FIRE FIGHTING

⁼

16058225.56

14 PLUMBING

⁼

28302872.62

15 LFT = 12800000.00

GRAND TOTAL = 672505365.54

SAY = 672505366

Name of Work : Tender for Construction of 100 Bedded Hospital for ESIC at Bhilai

SUMMARY

Sign and stamp of EPIL 47 Sign and stamp of bidder

Sl.

No.

DSR 2016

& MRDESCRIPTION OF ITEMS Total Qty. Unit DSR Rate

TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

EARTH WORKS

1 16.3

Supplying and Filling at site.By Mechanical

Transport including loading, unloading and filling

in building areas.

16.3.9 Good Earth 36426.12 cum 332.55 12113506.85

2.6

Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as

well as 10 sqm on plan) including getting out

and disposal of excavated earth lead upto 50 m

and lift upto 1.5 m, as directed by Engineer-in-

charge.2 2.6.1 All kinds of soil 27774.78 cum 125.95 3498233.33

2.7


(Hydraulic excavator)/ manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as

well as 10 sqm on plan) including getting out

and disposal of excavated earth lead upto 50 m

and lift upto 1.5 m, as directed by Engineer-

incharge.3 2.7.1 Ordinary rock 5476.69 cum 221.05 1210622.30

2.8


(Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5

m in width or 10 sqm on plan), including

dressing of sides and ramming of bottoms, lift

upto 1.5 m, including getting out the excavated

soil and disposal of surplus excavated soil as

directed, within a lead of 50 m.

1 2.8.1 All kinds of soils 158.00 cum 166.40 26291.87

4 2.25

Filling available excavated earth (excluding rock)

in trenches, plinth, sides of foundations etc. in

layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming

and watering, lead up to 50 m and lift upto 1.5

m.

30712.13 cum 125.75 3862049.93

5 2.27

Supplying and filling in plinth with sand under

floors, including watering, ramming,

consolidating and dressing complete.

450.98 cum 917.75 413888.59

6 2.31

Clearing jungle including uprooting of rank

vegetation, grass, brush wood, trees and

saplings of girth up to 30 cm measured at a

height of 1 m above ground level and removal of

rubbish up to a distance of 50 m outside the

periphery of the area cleared.

8464.91 sqm 7.20 60947.35

2.26

Extra for every additional lift of 1.5 m or part

thereof in excavation / banking excavated or

stacked materials.

7 2.26.1 All kinds of soil

a From 1.5mtr. To 3.0mtr. 10657.36 cum 51.75 551518.33

b From 3.0mtr. To 4.5mtr. 10366.85 cum 103.50 1072968.46

c from 4.5mtr. To 6mtr. 612.80 cum 155.25 95136.58

d from 6mtr. To 7.5mtr. 81.76 cum 207.00 16923.49

2.34Supplying chemical emulsion in sealed

containers including delivery as specified.

8 2.34.1Chlorpyriphos/ Lindane emulsifiable concentrate

of 20%1321.60 litre 185.95 245752.12

2.35

Diluting and injecting chemical emulsion for post-

CONSTRUCTIONAL anti-termite treatment

(excluding the cost of chemical emulsion) :

PROJECT: PROPOSED 100 BED ESIC HOSPITAL AT BHILAI, CHHATTISGARH

CIVIL WORKS BOQ


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

2.35.3

Treatment of soil under existing floors using

chemical emulsion @ one litre per hole, 300 mm

apart including drilling 12 mm diameter holes

and plugging with cement mortar 1 :2 (1 cement

: 2 Coarse sand) to match the existing floor:

9 2.35.3.1With Chlorpyriphos/Lindane E.C. 20% with 1%

concentration6587.20 sqm 131.90 868851.15

TOTAL ( EARTH WORKS) 24036690.33 0.00

CONCRETE WORKS

4.1

Providing and laying in position cement concrete

of specified grade excluding the cost of

centering and shuttering - All work up to plinth

level :

4.1.4

1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4

graded stone aggregate 40 mm nominal size). 0.00 cum 5390.45 0.00

10 4.1.5


graded stone aggregate 20 mm nominal size).

Below GF plinth lvl

578.85 cum 4927.00 2852011.49

4.1.8


graded stone aggregate 40 mm nominal size) 29.09 cum 4478.15 130260.43

11 4.1.101:5:10 (1 cement : 5 coarse sand (zone-III): 10


4.5

Providing and fixing up to floor five level precast

cement concrete string or lacing courses,

copings, bed plates, anchor blocks, plain

window sills, shelves, louvers, steps, stair cases,

etc., including hoisting and setting in position

with cement mortar 1:3 (1 Cement : 3 coarse

sand), cost of required Centering complete.

12 4.5.1

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3

graded stone aggregate 20mm nominal size). 181.41 cum 6772.45 1228611.51

13 4.17

Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand : 6

graded stone aggregate 20 mm nominal size)

over 75mm thick bed of dry brick ballast 40 mm

nominal size, well rammed and consolidated

and grouted with fine sand, including necessary

excavation, levelling & dressing & finishing the

top smooth.

1151.94 sqm 450.35 518778.12

TOTAL (CONCRETE WORKS) 6378457.86 0.00

REINFORCED CEMENT CONCRETE WORK

FORM WORK

5.9Centering and shuttering including strutting,

propping etc. and removal of form for :

14 5.9.1Foundations, footings, bases of columns, etc. for

mass concrete2422.08 sqm 193.45 468551.44

15 5.9.2

Walls (any thickness) including attached

pilasters, butteresses, plinth and string courses

etc.

2247.59 sqm 378.60 850935.75

16 5.9.3Suspended floors, roofs, landings, balconies and

access platform23355.60 sqm 422.30 9863070.13

17 5.9.4 Shelves (Cast in situ) 207.64 sqm 422.30 87684.81

18 5.9.5Lintels, beams, plinth beams, girders,

bressumers and cantilevers23595.71 sqm 342.90 8090967.25


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

19 5.9.6Columns, Pillars, Piers, Abutments, Posts and

Struts14773.28 sqm 467.85 6911677.42

20 5.9.7Stairs, (excluding landings) except spiral-

staircases699.45 sqm 419.35 293314.42

5.9.16 Edges of slabs and breaks in floors and walls

21 5.9.16.1 Under 20 cm wide 4238.71 meter 122.20 517970.12

5.11

Extra for additional height in centering,

shuttering where ever required with adequate

bracing, propping etc., including cost of de-

shuttering and decentering at all levels, over a

height of 3.5 m, for every additional height of 1

metre or part thereof (Plan area to be

measured).

22 5.11.1Suspended floors, roofs, landing, beams and

balconies (Plan area to be measured)21822.95 sqm 171.50 3742635.79

REINFORCED CEMENT CONCRETE

5.22

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

level.

23 5.22.6Thermo-Mechanically Treated bars of grade Fe-

500D or more.474666.33 kg 56.60 26866114.41

5.22A



position and binding all complete above plinth

level.

24 5.22A.6Thermo-Mechanically Treated bars of grade Fe-

500 D or more.896978.26 kg 56.60 50768969.60

5.30

Add for plaster drip course/ groove in plastered

surface or moulding to R.C.C. projections. 66.00 metre 34.15 2253.90

5.40

Providing and laying in position ready mixed M-

25 grade concrete for reinforced cement

concrete work, using fly ash and cement content

as per approved design mix, and manufactured

in fully automatic batching plant and transported

to site of work in transit mixer for all leads,

having continuous agitated mixer, manufactured

as per mix design of specified grade for

reinforced cement concrete work, including

pumping of R.M.C. from transit mixer to site of

laying, excluding the cost of centering,

shuttering, finishing and reinforcement, including

cost of admixtures in recommended proportions

as per IS : 9103 to accelerate / retard setting of

concrete, improve workability without impairing

strength and durability as per direction of the

Engineer - in - charge.

NOTE- (1) Cement content considered in this

item is @ 330 kg/cum. Excess/ less cement

used as per design mix is payable/

recoverable separately.“ (2) Fly ash

conforming to grade I of IS 3812 (Part-1) only

be used as part replacement of OPC as per

IS : 456. Uniform blending with cement to be

ensured in accordance with clauses 5.2 and

5.2.1 of IS:456 -2000 in the items of BMC and

RMC.


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

Note :- The above item shall be used

judiciously where specified quality of Fly Ash

is available for mixing in concrete. Also, the

guidelines issued by CDO, CPWD, vide

circular no. CDO/SE(RR)/Fly Ash (Main)/102

dated 9th April 2009 shall be followed in such

cases.

25 5.40.1 All works upto plinth level 3907.14 cum 6691.85 26145992.14

26 5.40.2 All works above plinth level upto floor V level 7122.40 cum 7495.40 53385215.59

5.44

Providing and fixing of expansion joint system

related with floor location as per drawings and

direction of Engineer-In-Charge. The joints

system will be of extruded aluminum base

members, self aligning / self centering

arrangement and support plates etc. as per

ASTM B221-02. The system shall be such that it

provides floor to floor /floor to wall expansion

control system for various vertical locations in

load application areas that accommodates multi

directional seismic movement without stress to

it's components. System shall consist of metal

profiles with a universal aluminum base member

designed to accommodate various project The cover plate shall be designed of width and

thickness required to satisfy projects movement

and loading requirements and secured to base

members by utilizing manufacturer‟s pre-

engineered self-centering arrangement that

freely rotates / moves in all directions. The Self -

centering arrangement shall exhibit circular

sphere ends that lock and slide inside the

corresponding aluminum extrusion cavity to

allow freedom of movement and flexure in all

directions including vertical displacement.

Provision of Moisture Barrier Membrane in the

Joint System to have watertight joint is

mandatory requirement all as per the

manufactures design and as approved by

Engineer -in-Charge. (Material shall conform to

ASTM 6063).

27 5.44.1 Floor Joint of 100 mm gap 140.25 metre 4741.05 664932.26

5.45

Providing and fixing of expansion joint system

related with wall joint (internal/ external) location

as per drawings and direction of Engineer-In-

Charge. The joints shall be of extruded

aluminum base members, self aligning /

centering arrangement and support plates as

per ASTM B221- 02. The material shall be such

that it provides an Expansion Joints System

suitable for vertical wall to wall/ wall to corner

application, both new and existing construction

in office Buildings & complexes with no slipping

down tendency amongst the components of the

Joint System. The Joint System shall utilize light

weight aluminum profiles exhibiting minimal

exposed aluminum surfaces mechanically snap

locking the multicellular to facilitate movement.

(Material shall conform to ASTM 6063.)

28 5.45.1 Wall Joint of 100 mm gap 240.35 metre 3928.00 944094.80


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

5.46

Providing and fixing of expansion joint system of

approved make and manufacture for various

roof locations as per approved drawings and

direction of Engineer-In-Charge. The joints shall

be of extruded aluminum base members with,

self aligning and self centering arragement

support plates as per ASTM B221-02. The

system shall be such that it provides water tight

roof to roof /roof to corner joint cover expansion

control system that is capable of

accommodating multidirectional seismic

movement without stress to its components.

System shall consist of metal profile that

incorporates a universal aluminum base

member designed to accommodate various

project conditions and roof treatments. The

cover plate shall be designed of width and

thickness required to satisfy movement and

loading requirements and secured to base

members by utilizing

manufacturer‟s pre-engineered self-centering

arrangement that freely rotates / moves in all

directions. The Self centering arrangement shall

exhibit circular sphere ends that lock and slide

inside the corresponding aluminum extrusion

cavity to allow freedom of movement and flexure

in all directions including vertical displacement.

The Joint System shall resists damage or

deterioration from the impact of falling ice,

exposure to UV, airborne contaminants and

occasional foot traffic from maintenance

personnel. Provision of Moisture Barrier

Membrane in the Joint System to have water

tight joint is mandatory requirement. (Material

shall confirm to ASTM 6063.)

29 5.46.1 Roof Joint of 100 mm gap 28.05 metre 4392.60 123212.43

TOTAL ( REINFORCED CEMENT CONCRETE

WORK)189727592.26 0.00

BRICK WORK

6.1

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

foundation and plinth in:

30 6.1.2Cement mortar 1:6 (1 cement : 6 coarse sand)

972.57 cum 4751.65 4621295.66

31 6.38

Providing and laying autoclaved aerated cement

blocks masonry with 100 mm / 200 mm thick

AAC blocks in super structure above plinth level

up to floor V level in cement mortar 1:4 (1

cement : 4 coarse sand ). The rate includes

providing and placing in position 2 Nos 6 mm dia

M.S. bars at every third course of masonry work.

4832.74 cum 6818.60 32952543.78

32 12.62

Providing and fixing thermal insulation with

Resin Bonded rock wool conforming to IS: 8183,

having density 48 kg/m3, 50 mm thick, wrapped

in 200 G Virgin Polythene Bags fixed to wall with

screws, rawel plug & washers and held and in

position by criss cossing GI wire etc. complete

as per directions of Engineer-in-Charge.

8154.80 sqm 223.80 1825044.99

TOTAL (BRICK WORK) 39398884.43 0.00

MARBLE & GRANITE WORK


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

8.2

Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity

counters, window sills, facias and similar

locations of required size, approved shade,

colour and texture laid over 20 mm thick base

cement mortar 1:4 (1 cement : 4 coarse sand),

joints treated with white cement, mixed with

matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges

to give high gloss finish etc. complete at all

levels.

33 8.2.1Raj Nagar Plain white marble/ Udaipur green

marble/ Zebra black marble

8.2.1.2 Area of slab over 0.50 sqm 89.46 sqm 1850.15 165511.09

8.2.2 Granite of any colour and shade

8.2.2.2 Area of slab over 0.50 sqm 117.81 sqm 3113.30 366778.18

8.3

Providing edge moulding to 18 mm thick marble

stone counters, Vanities etc., including machine

polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-

Charge.8.3.1 Marble work 128.59 metre 144.70 18606.97

34 8.3.2 Granite work 266.57 metre 245.70 65495.83

35 8.4

Extra for fixing marble /granite stone, over and

above corresponding basic item, in facia and

drops of width upto 150 mm with epoxy resin

based adhesive, including cleaning etc.

complete.

395.16 metre 266.25 105210.90

36 8.5

Extra for providing opening of required size &

shape for wash basin/ kitchen sink in kitchen

platform, vanity counter and similar location in

marble/ Granite/ stone work, including

necessary holes for pillar taps etc. including

moulding, rubbing and polishing of cut edges

etc. complete.

132.00 each 427.95 56489.40

TOTAL (MARBLE & GRANITE WORK) 778092.37 0.00

WOOD & PVC WORK

9.21

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction

with frame of 1st class hard wood and well

matched commercial 3 ply veneering with

vertical grains or cross bands and face veneers

on both faces of shutters:

37 9.21.135 mm thick including ISI marked Stainless

Steel butt hinges with necessary screws1249.71 sqm 1559.75 1949235.17

38 9.23

Extra for providing lipping with 2nd class teak

wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of

door shutter to be measured).

1249.71 sqm 365.85 457206.40

9.24

Extra for providing vision panel not exceeding

0.1 sqm in all type of flush doors (cost of glass

excluded) (overall area of door shutter to be

measured):39 9.24.1 Rectangular or square 160.23 sqm 162.60 26053.40

9.27

Providing and fixing wire gauge shutters using

galvanized M.S. wire gauge of average width of

aperture 1.4 mm in both directions with wire of

dia 0.63 mm, for doors, windows and clerestory

windows with hinges and necessary screws :

9.27.1 35 mm thick shutters

9.27.1.2With ISI marked stainless steel butt hinges of

required size

9.27.1.2.1 Second class teak wood 122.64 sqm 3040.30 372862.39


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

9.53

Providing 40x5 mm flat iron hold fast 40 cm long

including fixing to frame with 10 mm diameter

bolts, nuts and wooden plugs and embedding in

cement concrete block 30x10x15cm 1:3:6 mix (1

cement : 3 coarse sand : 6 graded stone

aggregate 20mm nominal size).

36.00 each 118.60 4269.60

ANODISED ALUMINIUM FITTINGS (ALL

FITTINGS SHALL BE ISI MARKED)

9.96

Providing and fixing aluminium sliding door

bolts, ISI marked anodised (anodic coating not

less than grade AC 10 as per IS : 1868),

transparent or dyed to required colour or shade,

with nuts and screws etc. complete :40 9.96.1 300x16 mm 714.00 each 212.45 151689.30

41 9.96.2 250x16 mm 720.00 each 189.20 136224.00

9.97

Providing and fixing aluminium tower bolts, ISI

marked, anodised (anodic coating not less than

grade AC 10 as per IS : 1868 ) transparent or

dyed to required colour or shade, with necessary

screws etc. complete :42 9.97.1 300x10 mm 714.00 each 99.70 71185.80

43 9.97.2 250x10 mm 720.00 each 88.10 63432.00

44 9.97.3 200x10 mm 1434.00 each 76.15 109199.10

9.100

Providing and fixing aluminium handles, ISI

marked, anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade, with necessary

screws etc. complete :45 9.100.1 125 mm 714.00 each 51.10 36485.40

46 9.100.2 100 mm 726.00 each 45.10 32742.60

9.101

Providing and fixing aluminium hanging floor

door stopper, ISI marked, anodised (anodic

coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour and

shade, with necessary screws etc. complete.

47 9.101.2 Twin rubber stopper 720.00 each 38.00 27360.00

48 9.103

Providing and fixing bright finished brass 100

mm mortice latch and lock, ISI marked, with six

levers and a pair of anodised (anodic coating not

less than grade AC 10 as per IS : 1868)

aluminium lever handles of approved quality with

necessary screws etc. complete.

717.00 each 622.15 446081.55

9.127

Providing & Fixing decorative high pressure

laminated sheet of plain / wood grain in gloss /

matt/ suede finish with high density protective

surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type S,

including cost of adhesive of approved quality.

49 9.127.2 1.0 mm thick 1611.54 sqm 518.00 834777.72

50 9.121

Providing and fixing Fiber Glass Reinforced

plastic (FRP) Door Frames of cross-section 90

mm x 45 mm having single rebate of 32 mm x

15 mm to receive shutter of 30 mm thickness

.The laminate shall be moulded with fire

resistant grade unsaturated polyester resin and

chopped mat. Door frame laminate shall be 2

mm thick and shall be filled with suitable

wooden block in all the three legs. The frame

shall be covered with fiber glass from all sides.

M.S. stay shall be provided at the bottom to

steady the frame.

890.40 metre 415.50 369961.20


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

9.122 Providing and fixing to existing door frames.

51 9.122.1

30 mm thick Glass Fibre Reinforced Plastic

(FRP) panelled door shutter of required colour

and approved brand and manufacture, made

with fire - retardant grade unsaturated polyester

resin, moulded to 3 mm thick FRP laminate for

forming hollow rails and styles, with wooden

frame and suitable blocks of seasoned wood

inside at required places for fixing of fittings, cast

monolithically with 5 mm thick FRP laminate for

panels conforming to IS: 14856, including fixing

to frames.

299.88 sqm 2187.35 655942.52

9.147B

Providing and fixing factory made uPVC white

colour fixed glazed windows/ventilators

comprising of uPVC multi-chambered frame and

mullion (where ever required) extruded profiles

duly reinforced with 1.60 ± 0.2 mm thick

galvanized mild steel section made from roll

forming process of required length (shape & size

according to uPVC profile), , uPVC extruded

glazing beads of appropriate dimension, EPDM

gasket, G.I fasteners 100 x 8 mm size for fixing

frame to finished wall, plastic packers, plastic

caps and necessary stainless steel screws etc.

Profile of frame shall be mitred cut and fusion

welded at all corners, mullion (if required) shall

be also fusion welded including drilling of holes

for fixing hardware's and drainage of water etc.

After fixing frame the gap between frame and

adjacent finished wall shall be filled with weather

proof silicon sealant over backer rod of required

size and of approved quality, all complete as per

approved drawing & direction of Engineer-in-

Charge. (Single / double glass panes and silicon

sealant shall be paid separately).

Note: For uPVC frame, sash and mullion

extruded profiles minus 5% tolerance in

dimension i.e. in depth & width of profile shall be

acceptable.

52 9.147B.1

Fixed window / ventilator made of (small series)

frame 47 x 50 mm & mullion 47 x 68 mm both

having wall thickness of 1.9 ± 0.2 mm and single

glazing bead of appropriate dimension. (Area

upto 0.75 sqm.)

184.20 sqm 5399.70 994624.74

9.147C


colour casement/ Casement cum fixed glazed

door comprising of uPVC multichambered

frame, sash and mullion (where ever required)

extruded profiles duly reinforced with 1.60 ± 0.2

mm thick galvanized mild steel section made

from roll forming process of required length

(shape & size according to uPVC profile), uPVC

extruded glazing beads of appropriate

dimension, EPDM gasket, zinc alloy (white

powder coated) 3D hinges and one handle on

each side of panels along with zinc plated mild

steel multi point locking having transmission

gear, cylinder with keeps and one side key,


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

G.I fasteners 100 x 8 mm size for fixing frame to

finished wall and necessary stainless steel

screws, etc. Profile of frame & sash shall be

mitred cut and fusion welded at all corners,

mullion (if required) shall be also fusion welded

including drilling of holes for fixing hardware's

and drainage of water etc. After fixing frame the

gap between frame and adjacent finished wall

shall be filled with weather proof silicon sealent

over backer rod of required size and of approved

quality, all complete as per approved drawing &

direction of Engineer-in-Charge. (Single / double

glass panes and silicon sealent shall be paid

separately).

Note: For uPVC frame, sash and mullion

extruded profiles minus 5% tolerance in

dimension i.e. in depth & width of profile shall be

acceptable.

53 9.147C.1

Casement door with 3D hinges made of (big

series) frame 67 x 64 mm & sash 67 x 110 mm

both having wall thickness of 2.3 ± 0.2 mm and

single glazing bead/ double glazing bead of

appropriate dimension. (Area of door upto 2.00

sqm).

305.04 sqm 7859.55 2397477.13

9.147D


colour sliding glazed window upto 1.50 m in

height dimension comprising of uPVC multi-

chambered frame with in-built roller track and

sash extruded profiles duly reinforced with 1.60

± 0.2 mm thick galvanized mild steel section

made from roll forming process of required

length (shape & size according to uPVC profile),

appropriate dimension of uPVC extruded glazing

beads and uPVC extruded interlocks, EPDM

gasket, wool pile, zinc alloy (white powder

coated) touch locks with hook, zinc alloy body

with single nylon rollers (weight bearing capacity

to be 40 kg), G.I fasteners 100 x 8 mm size for

fixing frame to finished wall and necessary

stainless steel screws etc. Profile of frame &

sash shall be mitred cut and fusion welded at all

corners, including drilling of holes for fixing

hardware's and drainage of water etc.

After fixing frame the gap between frame and

adjacent finished wall shall be filled with weather

proof silicon sealent over backer rod of required

size and of approved quality, all complete as per

approved drawing & direction of Engineer-in-

Charge. (Single / double glass panes, wire mesh

and silicon sealant shall be paid separately)

Note: For uPVC frame and sash extruded

profiles minus 5% tolerance in dimension i.e. in

depth & width of profile shall be acceptable.

9.147D.2

Three track three panels sliding window with fly

proof SS wire mesh (Two nos. glazed & one no.

wire mesh panels) made of (small series) frame

92 x 44 mm & sash 32 x 60 mm both having wall

thickness of 1.9 ± 0.2 mm and single glazing

bead of appropriate dimension (Area of window

upto 1.75 sqm).

276.96 sqm 7494.70 2075732.11


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

54 9.147D.4

Three track three panels sliding window with fly

proof S.S wire mesh (Two nos. glazed & one no.

wire mesh panels) made of (big series) frame

116 x 45 mm & sash 46 x 62 mm both having

wall thickness of 2.3 ± 0.2 mm and single

glazing bead / double glazing bead of

appropriate dimension. (Area of window above

1.75 sqm).

808.82 sqm 7261.20 5873032.83

9.135

Providing and fixing fly proof stainless steel

grade 304 wire gauge, to windows and

clerestory windows using wire gauge with

average width of aperture 1.4 mm in both

directions with wire of dia. 0.50 mm all complete.

55 9.135.2 With 12 mm mild steel U beading 673.11 sqm 1094.10 736449.65

56 9.161

Providing and fixing fire resistant door frame of

section 50 x 60 mm on horizontal side & 35 x 60

mm on vertical sides having built in rebate made

out of 1.6 mm thick GI sheet ( Zinc coating not

less than 120gm/m²) suitable for mounting 120

min Fire Rated Glazed Door Shutters. The

frame shall be filled with Mineral wool Insulation

having density min 96Kg/m³ . The frame will

have a provision of G.I. Anchor fastners 14 nos (

5 each on vertical style & 4 on horizontal style of

size M10 x 80 ) suitable for fixing in the opening

along with Factory made Template for SS Ball

Bearing Hinges of Size 100x89x3mm for fixing

of fire rated glazed shutter. The frame shall be

finished with a approved fire resistant primer or

Powder coating of not less than 30 micron in

desired shade as per the directions of Engineer -

in- charge . (Cost of SS ball bearing hinges is

excluded).

176.40 metre 1260.00 222264.00

57 9.162

Providing and fixing 60 mm thick glazed fire

resistant door shutters of 120 min Fire Rating

confirming to IS:3614 (Part II) or EN1634-

1:1999, tested and certified as per laboratory

approved by Engineer-in-charge, with suitable

mounting on door frame, consisting of vertical

styles, top rail & side rail 60 mm x 60 mm wide

and bottom rail of 110 mm x 60 mm made out of

1.6mm thick G.I. sheet (zinc coating not less

than 120gm/m²) duly filled mineral wool

insulation having density min 96 kg/m³ and fixing

with necessary stainless steel ball bearing

hinges of size 100x89x3mm of approved make,

including applying a coat of approved fire

resistant primer or powder coating not less than

30 micron etc all complete as per direction of

Engineer-in-charge (panelling to be paid for

seperately).

97.02 sqm 6839.35 663553.74

58 9.139

Providing and fixing panic bar / latch (Double

point) fitted with a single body, Trim Latch &

Lock on back side of the Panic Latch of reputed

brand and manufacture to be approved by the

Engineer- in- charge, all complete.

31.00 each 6143.30 190442.30


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

25.3

Providing, assembling and supplying vision

glass panels (IGUs) comprising of hermetically-

sealed 6-12- 6 mm insulated glass (double

glazed) vision panel units of size and shape as

required and specified, comprising of an outer

heat strengthened float glass 6mm thick, of

approved colour and shade with reflective soft

coating on surface # 2 of approved colour and

shade, an inner Heat strengthned clear float

glass 6mm thick, spacer tube 12mm wide,

dessicants, including primary seal and

secondary seal (structural silicone sealant) etc.

all complete for the required performances, as

per the Architectural drawings, as per the

approved shop drawings, as specified and as

directed by the Engineer-in-Charge. The IGUs

shall be assembled in the factory/ workshop of

the glass processor.“(Payment for fixing of IGU

Panels in the curtain glazing is included in cost

of item No.26.2)“For payment, only the actual

area of glass on face # 1 of the glass panels

(excluding the areas of the grooves and weather

silicone sealant) provided and fixed in position,

shall be measured in sqm.

(i)

Coloured tinted float glass 6mm thick substrate

with reflective soft coating on face # 2, + 12mm

Airgap + 6mm Heat Strengthened clear Glass of

approved make having properties as visible

Light transmittance (VLT) of 25 to 35 %, Light

reflection internal 10 to 15%, light reflection

external 10 to 20 %, shading coefficient (0.25-

0.28) and U value of 3.0 to 3.3 W/m2 degree K

etc. The properties of performance glass shall

be decided by technical sanctioning authority as

per the site requirement.

1045.84 sqm 3730.70 3901700.37

9.7.7 Providing and fixing Float glass panes

59 9.7.7.1 4 mm thick glass pane 403.44 sqm 1169.60 471866.23

60 9.12

Extra for providing frosted glass panes 4 mm

thick instead of ordinary float glass panes 4 mm

thick in doors, windows and clerestory window

shutters. (Area of opening for glass panes

excluding portion inside rebate shall be

measured).

53.46 sqm 74.35 3974.75

TOTAL ( Wood & PVC WORK) 23275826.00 0.00

STEEL WORK


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

10.2

Structural steel work riveted, bolted or welded in

built up sections, trusses and framed work,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer

all complete.

35000.00 kg 67.60 2366000.00

10.3

Providing and fixing in position collapsible steel

shutters with vertical channels 20x10x2 mm and

braced with flat iron diagonals 20x5 mm size,

with top and bottom rail of T-iron 40x40x6 mm,

with 40 mm dia steel pulleys, complete with

bolts, nuts, locking arrangement, toppers,

handles, including applying a priming coat of

approved steel primer.

67.56 sqm 5360.65 362165.51

10.5

Providing and fixing 1mm thick M.S. sheet door

with frame of 40x40x6 mm angle iron and 3 mm

M.S. gusset plates at the junctions and corners,

all necessary fittings complete, including

applying a priming coat of approved steel

primer.

10.5.1Using M.S. angles 40x40x6 mm for diagonal

braces75.12 sqm 2870.25 215613.18

10.6

Supplying and fixing rolling shutters of approved

make, made of required size M.S. laths,

interlocked together through their entire length

and jointed together at the end by end locks,

mounted on specially designed pipe shaft with

brackets, side guides and arrangements for

inside and outside locking with push and pull

operation complete, including the cost of

providing and fixing necessary 27.5 cm long wire

springs manufactured from high tensile steel

wire of adequate strength conforming to IS:

4454 - part 1 and M.S. top cover of required

thickness for rolling shutters.

10.6.280x1.20 mm M.S. laths with 1.20 mm thick top

cover81.00 sqm 1841.40 149153.40

10.7Providing and fixing ball bearing for rolling

shutters.32.00 each 379.30 12137.60

10.8

Extra for providing mechanical device chain and

crank operation for operating rolling shutters.

10.8.1Exceeding 10.00 sqm and upto 16.80 sqm in the

area81.00 sqm 724.05 58648.05

10.9

Extra for providing grilled rolling shutters

manufactured out of 8 mm dia M.S. bar instead

of laths as per design approved by Engineer-in-

charge,(area of grill to be measured).

81.00 sqm 313.60 25401.60

10.14

Providing and fixing pressed steel door frames

conforming to IS: 4351, manufactured from

commercial mild steel sheet of 1.60 mm

thickness, including hinges, jamb, lock jamb,

bead and if required angle threshold of mild

steel angle of section 50x25 mm, or base ties of

1.60 mm, pressed mild steel welded or rigidly

fixed together by mechanical means, including

M.S. pressed butt hinges 2.5 mm thick with

mortar guards, lock strike-plate and shock

absorbers as specified and applying a coat of

approved steel primer after pre-treatment of the

surface as directed by Engineer-in-charge:

10.14.1 Profile B

61 10.14.1.1Fixing with adjustable lugs with split end tail to

each jamb2683.30 metre 340.35 913261.16


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

62 10.18

Providing and fixing circular/ Hexagonal cast

iron or M.S. sheet box for ceiling fan clamp, of

internal dia 140 mm, 73 mm height, top lid of 1.5

mm thick M.S. sheet with its top surface hacked

for proper bonding, top lid shall be screwed into

the cast iron/ M.S. sheet box by means of 3.3

mm dia round headed screws, one lock at the

corners. Clamp shall be made of 12 mm dia

M.S. bar bent to shape as per standard drawing.

924.00 each 130.10 120212.40

10.25

Steel work welded in built up sections/ framed

work, including cutting, hoisting, fixing in position

and applying a priming coat of approved steel

primer using structural steel etc. as required.

63 10.25.2In gratings, frames, guard bar, ladder, railings,

brackets, gates and similar works35197.48 kg 85.95 3025223.45

64 10.28

Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing,

polishing and making curvature (wherever

required) and fitting the same with necessary

stainless steel nuts and bolts complete, i/c fixing

the railing with necessary accessories &

stainless steel dash fasteners , stainless steel

bolts etc., of required size, on the top of the floor

or the side of waist slab with suitable

arrangement as per approval of Engineer-in-

charge, (for payment purpose only weight of

stainless steel members shall be considered

excluding fixing accessories such as nuts, bolts,

fasteners etc.).

14023.19 kg 472.40 6624557.20

TOTAL ( STEEL WORK) 13872373.55 0.00

FLOORING WORK

8.13

Providing and laying Polished Granite stone

flooring in required design and patterns, in linear

as well as curvilinear portions of the building, all

complete as per the architectural drawings, with

18 mm thick stone slab over 20 mm (average)

thick base of cement mortar 1:4 (1 cement : 4

coarse sand), laid and jointed with cement slurry

and pointing with white cement slurry admixed

with pigment of matching shade, including

rubbing, curing and polishing etc. all complete

as specified and as directed by the Engineer-in-

65 8.13.1Polished Granite stone slab jet Black, Cherry

Red, Elite Brown, Cat Eye or equivalent.1548.60 sqm 2937.70 4549326.16

11.24Extra for pre finished nosing to treads of steps of

marble / Granite stone.0.00 metre 306.25 0.00

11.25

Extra for marble / Granite stone flooring in

treads of steps and risers using single length up

to 2.00 metre.

24.00 sqm 357.95 8590.80

11.20

Chequerred precast cement concrete tiles 22

mm thick in footpath & courtyard, jointed with

neat cement slurry mixed with pigment to match

the shade of tiles, including rubbing and

cleaning etc. complete, on 20 mm thick bed of

cement mortar 1:4 (1 cement: 4 coarse sand).

66 11.20.4 Ordinary cement without any pigment 1051.00 sqm 661.35 695075.54


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

11.26

Kota stone slab flooring over 20 mm (average)

thick base laid over and jointed with grey cement

slurry mixed with pigment to match the shade of

the slab, including rubbing and polishing

complete with base of cement mortar 1 : 4 (1

cement : 4 coarse sand) :67 11.26.1 25 mm thick 8356.64 sqm 1158.10 9677828.61

81 11.27

Kota stone slabs 20 mm thick in risers of steps,

skirting, dado and pillars laid on 12 mm

(average) thick cement mortar 1:3 (1 cement: 3

coarse sand) and jointed with grey cement slurry

mixed with pigment to match the shade of the

slabs, including rubbing and polishing complete.

810.65 sqm 1238.20 1003744.21

11.31Extra for pre finished nosing in treads of steps of

Kota stone/ sand stone slab.252.00 sqm 84.85 21382.20

11.33

25 mm wooden planking, tongued and grooved

in flooring, including fixing with iron screws

complete with :

69 11.33.2 Second class deodar wood 45.21 sqm 2307.80 104333.10

70 11.36

Providing and fixing Ist quality ceramic glazed

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

14469.79 sqm 744.80 10777098.49

11.37A

Providing and fixing 1st quality ceramic glazed

floor tiles conforming to IS : 15622 (thickness to

be specified by the manufacturer ) of approved

make in all colours, shades except burgundy,

bottle green, black of any size as approved by

Engineer-in-Charge in skirting, risers of steps

and dados over 12 mm thick bed of cement

Mortar 1:3 (1 cement: 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm including pointing in white cement mixed

with pigment of

matching shade complete.

98.45 sqm 660.20 64996.69

71 11.40

Providing and laying rectified Glazed Ceramic

floor tiles of size 300x300 mm or more

(thickness to be specified by the manufacturer),

of 1st quality conforming to IS : 15622, of

approved make, in all colours, shades, except

White, Ivory, Grey, Fume Red Brown, laid on 20

mm thick Cement Mortar 1:4 (1 Cement : 4

Coarse sand), jointing with grey cement slurry @

3.3kg/sqm including pointing the joints with

white cement and matching pigments etc.,

complete.

2682.50 sqm 901.05 2417068.25

11.41

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by the

manufacturer) with water absorption less than

0.08% and conforming to IS: 15622, of approved

make, in all colours and shades, laid on 20mm

thick cement mortar 1:4 (1 cement : 4 coarse

sand), jointing with grey cement slurry @

3.3kg/sqm including grouting the joints with

white cement and matching pigments etc., 72 11.41.2 Size of Tile 600x600 mm 2154.90 sqm 1119.40 2412195.06


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

11.23

Marble stone flooring with 18 mm thick marble

stone, as per sample of marble approved by

Engineer-in-charge, over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with grey cement slurry,

including rubbing and polishing complete with :

73 11.23.1 Makrana white second quality 777.70 sqm 2724.75 2119038.08

11.20

Chequerred precast cement concrete tiles 22

mm thick in footpath & courtyard, jointed with

neat cement slurry mixed with pigment to match

the shade of tiles, including rubbing and

cleaning etc. complete, on 20 mm thick bed of

cement mortar 1:4 (1 cement: 4 coarse sand).

11.20.4 Ordinary cement without any pigment 170.31 sqm 661.35 112636.50

TOTAL ( FLOORING WORK) 33963313.67 0.00

ROOFING WORK

12.21

Providing gola 75x75 mm in cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 stone

aggregate 10 mm and down gauge), including

finishing with cement mortar 1:3 (1 cement : 3

fine sand) as per standard design :

74 12.21.1 In 75x75 mm deep chase 1220.53 metre 153.00 186741.47

75 12.22

Making khurras 45x45 cm with average

minimum thickness of 5 cm cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate of 20 mm nominal size) over P.V.C.

sheet 1 m x1 m x 400 micron, finished with 12

mm cement plaster 1:3 (1 cement : 3 coarse

sand) and a coat of neat cement, rounding the

edges and making and finishing the outlet

complete.

41.00 each 187.60 7691.60

12.45

Providing and fixing false ceiling at all height

including providing and fixing of frame work

made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of

120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25

mm wide x 1.6 mm thick with flanges of 27 mm

and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener

12.5 mm dia x 50mm long with 6mm dia bolts,

other flange of cleat fixed to the angle hangers

of 25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200

mm centre to centre, to which the ceiling section

0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of

10.5 mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made

out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter

channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the

help of rawl plugs at 450 mm centre, with 25mm

long dry wall screws @ 230 mm interval,

including fixing of gypsum board


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

to ceiling section and perimeter channel with

the help of dry wall screws of size 3.5 x 25 mm

at 230 mm c/c, including jointing and finishing to

a flush finish of tapered and square edges of the

board with recommended jointing compound ,

jointing tapes , finishing with jointing compound

in 3 layers covering upto 150 mm on both sides

of joint and two coats of primer suitable for

board, all as per manufacturer's specification

and also including the cost of making openings

for light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably fixed,

all complete as per drawings, specification and

direction of the Engineer in Charge but

excluding the cost of painting with :

76 12.45.212.5 mm thick tapered edge gypsum fire

resistant board conforming to IS: 2095-Part I1217.70 sqm 922.05 1122780.29

12.52

Providing and fixing tiled false ceiling of

specified materials of size 595x595 mm in true

horizontal level, suspended on inter locking

metal grid of hot dipped galvanized steel

sections ( galvanized @ 120 grams/ sqm, both

side inclusive) consisting of main "T" runner with

suitably spaced joints to get required length and

of size 24x38 mm made from 0.30 mm thick

(minimum) sheet, spaced at 1200 mm center to

center and cross "T" of size 24x25 mm made of

0.30 mm thick (minimum) sheet, 1200 mm long

spaced between main "T" at 600 mm center to

center to

form a grid of 1200x600 mm and secondary

cross "T" of length 600 mm and size 24x25 mm

made of 0.30 mm thick (minimum) sheet to be

interlocked at middle of the 1200x600 mm panel

to form grids of 600x600 mm and wall angle of

size 24x24x0.3 mm and laying false ceiling tiles

of approved texture in the grid including,

required cutting/making, opening for services

like diffusers, grills, light fittings, fixtures, smoke

detectors etc. Main "T" runners to be suspended

from ceiling using GI slotted cleats of size 27 x

37 x 25 x1.6 mm fixed to ceiling with 12.5 mm

dia and 50 mm long dash fasteners, 4 mm GI

adjustable rods with galvanised butterfly level

clips of size 85 x 30 x 0.8 mm spaced at 1200

mm center to center along main T, bottom

exposed width of 24 mm of all T-sections shall

be pre-painted with polyester paint, all complete

for all heights as per specifications, drawings

77 12.52.1

GI Metal Ceiling Lay in plain Tegular edge

Global white color tiles of size 595x595 mm, and

0.5 mm thick with 8 mm drop; made of G I sheet

having galvanizing of 100 gms/sqm (both sides

inclusive) and electro statically polyester powder

coated of thickness 60 microns (minimum),

including factory painted after bending.

3247.20 sqm 1041.95 3383420.04

TOTAL (Carried Over to Summary of

ROOFING WORK)4700633.40 0.00

FINISHING WORK

For Internal Finishing

13.1 12 mm cement plaster of mix :

13.1.2 1:6 (1 cement: 6 fine sand) 2030.73 sqm 160.35 325627.47

13.215 mm cement plaster on the rough side of

single or half brick wall of mix :

13.2.2 1:6 (1 cement: 6 fine sand) 147.55 sqm 185.20 27325.80


78 13.4.2 1:6 (1 cement: 6 coarse sand) 30911.26 sqm 168.25 5200820.13


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount


13.6.2 1:6 (1 cement: 6 coarse sand) 173.82 sqm 232.85 40474.96

13.9

Cement plaster 1:3 (1 cement: 3 coarse sand)

finished with a floating coat of neat cement.

13.9.1 12 mm cement plaster 1787.81 sqm 234.70 419598.54


79 13.16.1 1:3 (1 cement : 3 fine sand) 8841.87 sqm 143.80 1271460.50

80 13.26

Providing and applying plaster of paris putty of 2

mm thickness over plastered surface to prepare

the surface even and smooth complete.262.48 sqm 118.70 31156.57

13.37White washing with lime to give an even shade :

81 13.37.1 New work (three or more coats) 3214.51 sqm 17.25 55450.30

13.41

Distempering with oil bound washable distemper

of approved brand and manufacture to give an

even shade :

82 13.41.1New work (two or more coats) over and

including water thinnable priming coat with

cement primer

7717.19 sqm 93.70 723100.95

13.44

Finishing walls with water proofing cement paint

of required shade : FOR EXTERNAL WALLS

ONLY

13.44.1New work (Two or more coats applied @ 3.84

kg/10 sqm)89.34 sqm 58.80 5252.93

13.61Painting with synthetic enamel paint of approved

brand and manufacture to give an even shade :

13.61.1 Two or more coats on new work 633.09 sqm 78.40 49634.21

83 13.80

Providing and applying white cement based

putty of average thickness 1 mm, of approved

brand and manufacturer, over the plastered wall

surface to prepare the surface even and smooth

complete.

38245.85 sqm 87.35 3340775.41

13.82

Wall painting with acrylic emulsion paint, having

VOC (Volatile Organic Compound ) content less

than 50 grams/ litre, of approved brand and

manufacture, including applying additional coats

wherever required, to achieve even shade and

colour.84 13.82.2 Two coats 38551.02 sqm 73.90 2848920.39

13.84

Painting with synthetic enamel paint, having

VOC (Volatile Organic Compound) content less

than 150 grams/ litre, of approved brand and

manufacture, including applying additional coats

wherever required to achieve even shade and

colour.85 13.84.2 Two coats 2650.58 sqm 75.00 198793.71

13.85

Applying priming coats with primer of approved

brand and manufacture, having low VOC

(Volatile Organic Compound ) content.

86 13.85.2

With ready mixed red oxide zinc chromatic on

steel / iron works having VOC content less than

250 grams/ litre

2561.16 sqm 32.55 83365.77

87 13.85.3

With water thinnable cement primer on wall

surface having VOC content less than 50

grams/litre

38551.02 sqm 36.95 1424460.20

For External Finishing


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

88 13.72

Washed stone grit plaster on exterior walls

height upto 10 metre above ground level, in two

layers, under layer 12 mm cement plaster 1:4 (1

cement : 4 coarse sand ), furrowing the under

layer with scratching tool, applying cement slurry

on the under layer @ 2 Kg of cement per square

metre, top layer 15 mm cement plaster 1:1/ 2:2

(1 cement: 1/2 coarse sand : 2 stone chipping

10 mm nominal size), in panels with groove all

around as per approved pattern, including

scrubbing and washing the top layer with

brushes and water to expose the stone

chippings ,complete as per specification and

direction of Engineer-in- charge (payment for

providing grooves shall be made separately).

20809.94 sqm 582.60 12123869.30

89 13.74

Extra for washed grit plaster on exterior walls of

height more than 10 m from ground level for

every additional height of 3 m or part thereof.8749.79 sqm 85.90 751607.24

13.73

Forming groove of uniform size in the top layer

of washed stone grit plaster as per approved

pattern using wooden battens, nailed to the

under layer, including removal of wooden

battens, repair to the edges of panels and

finishing the groove complete as per

specifications and direction of the Engineer-in-

charge :90 13.73.1 15 mm wide and 15 mm deep groove 42904.63 metre 34.40 1475919.27

91 13.77

Extra for using white cement in place of ordinary

cement in the top layer of the item of washed

stone grit plaster.

20071.88 sqm 63.90 1282592.92

13.47

Finishing walls with Premium Acrylic Smooth

exterior paint with Silicone additives of required

shade:

13.47.1

New work (Two or more coats applied @ 1.43

ltr/10 sqm over and including priming coat of

exterior primer applied @ 2.20 kg/10 sqm)1500.00 sqm 96.80 145200.00

20 16.53

Providing and fixing concertina coil fencing with

punched tape concertina coil 600 mm dia 10

metre openable length ( total length 90 m),

having 50 nos rounds per 6 metre length, upto 3

m height of wall with existing angle iron 'Y'

shaped placed 2.4 m or 3.00 m apart and with 9

horizontal R.B.T. reinforced barbed wire, stud

tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or G.I.

barbed wire tied to angle iron, all complete as

per direction of Engineer-in-charge, with

reinforced barbed tape(R.B.T.) / Spring core

(2.5mm thick) wire of high tensile strength of

165 kg/ sq.mm with tape (0.52 mm thick) and

weight 43.478 gm/metre (cost of M.S. angle,

C.C. blocks shall be paid separately)

611.34 metre 255.00 155890.68


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

20.2

Boring, providing and installation bored cast-in-

situ reinforced cement concrete piles of grade M-

25 of specified diameter and length below the

pile cap, to carry a safe working load not less

than specified, excluding the cost of steel

reinforcement but including the cost of boring

with bentonite solution and temporary casing of

appropriate length for setting out and removal of

same and the length of the pile to be embedded

in the pile cap etc. by percussion drilling using

Direct mud circulation (DMC) or Bailer and

chisel technique by tripod and mechanical

Winch Machine all complete, including removal

of excavated earth with all its lifts and leads

(length of pile for payment shall be measured up

to bottom of pile cap).

Note: Truck Mounted rotary/TMR/Tubewell

boring machine shall not be used.

21 20.2.1 450 mm dia piles 1769.62 metre 1496.45 2648142.79

20.6

Vertical load testing of piles in accordance with

IS 2911 (Part IV) including installation of loading

platform by Kentledge/Anchor piles method and

preparation of pile head or construction of test

cap and dismantling of test cap after test etc.

complete as per specification & the direction of

Engineer in-charge.

Note: 1. Initial and Routine Load Test shall not

be carried out by Dynamic method of testing.

Note: 2. Testing agency shall submitt the design

of loading platform for the approval of Engineer-

in-charge.

20.6.1 Single pile upto 50 tonne Safe capacity

22 20.6.1.1Initial test (Test Load 2.5 times the Safe

capacity)1.00 per test 38561.80 38561.80

23 20.6.1.2Routine test (Test Load 1.5 times the Safe

capacity)2.00 per test 17422.50 34845.00

TOTAL (Finishing WORK) 31825406.56 0.00

ALUMINIUM WORK

21.4

Providing and fixing double action hydraulic floor

spring of approved brand and manufacture

conforming to IS : 6315, having brand logo

embossed on the body / plate with double spring

mechanism and door weight upto 125 kg, for

doors, including cost of cutting floors,

embedding in floors as required and making

good the same matching to the existing floor

finishing and cover plates with brass pivot and

single piece M.S. sheet outer box with slide

plate etc. complete as per the direction of

Engineer-in-charge.

92 21.4.1With stainless steel cover plate minimum 1.25

mm thickness22.00 each 2054.40 45196.80

TOTAL ( Aluminium WORK) 45196.80 0.00

WATER PROOFING


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

22.1

Providing and laying integral cement based

treatment for water proofing on horizontal

surface at all depth below ground level for under

ground structures as directed by Engineer-in-

Charge and consisting of :

(i) Ist layer of 22 mm to 25 mm thick approved

and specified rough stone slab over a 25 mm

thick base of cement mortar 1:3 (1 cement : 3

coarse sand) mixed with water proofing

compound conforming to IS:2645 in the

recommended proportion over the leveling

course (leveling course to be paid separately).

Joints sealed and grouted with cement slurry

mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3

(1 cement: 3 coarse sand) mixed with water

proofing compound in recommended

proportions.

(iii) Finishing top with stone aggregate of 10 mm

to 12 mm nominal size spreading @ 8

cudm/sqm thoroughly embedded in the 2nd

layer.

22.1.1 Using rough kota stone. 626.05 sqm 1017.55 637041.25

22.2


treatment for water proofing on the vertical

surface by fixing specified stone slab 22 mm to

25 mm thick with cement slurry mixed with water

proofing compound conforming to IS:2645 in

recommended proportions with a gap of 20 mm

(minimum) between stone slabs and the

receiving surfaces and filling the gaps with neat

cement slurry mixed with water proofing

compound and finishing the exterior of stone

slab with cement mortar 1:3 (1 cement : 3

coarse sand) 20 mm thick with neat cement

punning mixed with water proofing compound in

recommended proportion complete at all levels

and as directed by Engineer-in-charge :

22.2.1 Using rough Kota stone 881.56 sqm 1253.30 1104861.65

22.3

Providing and laying water proofing treatment to

vertical and horizontal surfaces of depressed

portions of W.C., kitchen and the like consisting

of:

(i) Ist course of applying cement slurry @ 4.4

kg/sqm mixed with water proofing compound

conforming to IS 2645 in recommended

proportions including rounding off junction of

vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1

cement : 3 coarse sand) mixed with water

proofing compound in recommended proportion

including rounding off junction of vertical and

horizontal surface.

(iii) IIIrd course of applying blown or residual

bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet.

(Overlaps at joints of PVC sheet should be 100

mm wide and pasted to each other

with bitumen @ 1.7 kg/ sqm).

229.01 sqm 505.90 115855.65


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

19.16

Providing orange colour safety foot rest of

minimum 6 mm thick plastic encapsulated as

per IS : 10910, on 12 mm dia steel bar

conforming to IS: 1786, having minimum cross

section as 23 mmx25 mm and over all minimum

length 263 mm and width as 165 mm with

minimum 112 mm space between protruded

legs having 2 mm tread on top surface by

ribbing or chequering besides necessary and

adequate anchoring projections on tail length on

138 mm as per standard drawing and suitable to

with stand the bend test and chemical resistance

test as per specifications and having

manufacture's permanent identification mark to

be visible even after fixing, including fixing in

manholes with 30x20x15 cm cement concrete

block 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 20 mm nominal size) complete

as per design.

192.00 each 327.90 62956.80

93 22.5

Providing and laying water proofing treatment in

sunken portion of WCs, bathroom etc., by

applying cement slurry mixed with water proofing

cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488

kg/sqm mixed with water proofing cement

compound @ 0.253 kg/ sqm. This layer will be

allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242

kg/sqm mixed with water proofing cement

compound @ 0.126 kg/sqm. This layer will be

allowed to air cure for 4 hours followed with

water curing for 48 hours. The rate includes

preparation of surface, treatment and sealing of

all joints, corners, junctions of pipes and

masonry with polymer mixed slurry.

1049.88 sqm 298.30 313180.67

For Terrace

22.6

Providing and laying water proofing treatment on

roofs of slabs by applying cement slurry mixed

with water proofing cement compound

consisting of applying:

(a) after surface preparation, first layer of slurry

of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/sqm.

(b) laying second layer of Fibre glass cloth when

the first layer is still green. Overlaps of joints of

fibre cloth should not be less than 10 cm.

94

(c) third layer of 1.5 mm thickness consisting of

slurry of cement @ 1.289 kg/sqm mixed with

water proofing cement compound @ 0.670

kg/sqm and coarse sand @ 1.289 kg/sqm. This

will be allowed to air cure for 4 hours followed by

water curing for 48 hours. The entire treatment

will be taken upto 30 cm on parapet wall and

tucked into groove in parapet all around.

(d) fourth and final layer of brick tiling with

cement mortar (which will be paid for

separately.For the purpose of measurement the

entire treated surface will be measured.

4269.85 sqm 395.00 1686590.83


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

22.7


water proofing treatment including preparation of

surface as required for treatment of roofs,

balconies, terraces etc consisting of following

operations:

(a) Applying a slurry coat of neat cement using

2.75 kg/sqm of cement admixed with water

proofing compound conforming to IS. 2645 and

approved by Engineer-in-charge over the RCC

slab including adjoining walls upto 300 mm

height including cleaning the surface before

treatment.

(b) Laying brick bats with mortar using broken

bricks/brick bats 25 mm to 115 mm size with

50% of cement mortar 1:5 (1 cement : 5 coarse

sand) admixed with water proofing compound

conforming to IS : 2645 and approved by

Engineer-in-charge over 20 mm thick layer of

cement mortar of mix 1:5 (1 cement :5 coarse

sand) admixed with water proofing compound

conforming to IS : 2645 and approved by

Engineer-in-charge to required slope and

treating similarly the adjoining walls upto 300

mm height including rounding of junctions of

walls and slabs.

(c) After two days of proper curing applying a

second coat of cement slurry using 2.75 kg/ sqm

of cement admixed with water proofing 22.7.1

With average thickness of 120 mm and

minimum thickness at khurra as 65 mm.948.99 sqm 1034.65 981869.40

95 12.56

Providing and laying roof insulation with 40 mm

thick impervious sprayed, closed cell free Rigid

Polyurethane foam over deck insulation

conforming to IS - 12432 Pt. III (density of foam

being 40-45 kg/ cum), over a coat of

polyurethane primer applied @ 6-8 sqm per litre,

laying 400 G polythene sheet over PUF spray

and providing a wearing course of 40 mm thick

cement screed 1:2:4 (1 cement : 2 coarse sand :

4 stone aggregate 20 mm nominal size) in

chequered rough finish, in panels of 2.5 m x 2.5

m and embedding with 24 G wire netting and

sealing the joints with polymerized mastic, all

complete as per direction of Engineer-in-Charge.

3308.51 sqm 1151.05 3808265.04

96 11.37

Providing and laying Ceramic glazed floor tiles

of size 300x300 mm (thickness to be specified

by the manufacturer) of 1st quality conforming to

IS : 15622 of approved make in colours such as

White, Ivory, Grey, Fume Red Brown, laid on 20

mm thick cement mortar 1:4 (1 Cement : 4

Coarse sand), jointing with grey cement slurry @

3.3kg/sqm including pointing the joints with

white cement and matching pigment etc.,

complete.

4269.85 sqm 688.35 2939151.39

97 4.1.6

1:3:6 (1 Cement : 3 coarse sand (zone-III): 6


TOTAL (WATER PROOFING WORK) 13191578.23 0.00

ROAD WORKS

1 16.1

Preparation and consolidation of sub grade with

power road roller of 8 to 12 tonne capacity after

excavating earth to an average of 22.5 cm

depth, dressing to camber and consolidating

with road roller including making good the

undulations etc. and re-rolling the sub grade and

disposal of surplus earth with lead upto 50

metres.

7887.45 sqm 90.10 710658.84


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

2 16.2

Extra for compaction of earth work in

embankment under optimum moisture

conditions to give at least 95% of the maximum

dry density (proctor density).

7493.07 cum 10.70 80175.88

16.3 Supplying and stacking at site.

3 16.3.1 90 mm to 45 mm size stone aggregate 867.62 cum 1336.05 1159182.37

4 16.3.2 63 mm to 45 mm size stone aggregate 591.56 cum 1449.30 857345.61

5 16.3.3 53 mm to 22.4 mm size stone aggregate 473.25 cum 1542.25 729864.77

6 16.3.6Stone screening 13.2 mm nominal size (Type A)

197.19 cum 1505.60 296883.45

7 16.3.7Stone screening 11.2 mm nominal size (Type B)

118.31 cum 1462.05 172977.60

8 16.3.9

Good earth ( FILLING AT SITE SUPLLY FROM

5 KM. AWYE TO SITE LUMSUM DISTANCE

TAKEN )

2789.33 cum 332.55 927591.60

9 16.3.10 Moorum 193.24 cum 643.20 124293.52

10 16.4

Laying, spreading and compacting stone

aggregate of specified sizes to WBM

specifications in uniform thickness, hand

picking, rolling with 3 wheeled road / vibratory

roller 8-10 tonne capacity in stages to proper

grade and camber, applying and brooming

requisite type of screening / binding material to

fill up interstices of coarse aggregate, watering

and compacting to the required density .

2366.23 cum 449.10 1062675.53

5.22



position and binding all complete upto plinth

level.

5.22.6Thermo-Mechanically Treated bars of grade Fe-

500D or more.48438.76 kg 56.60 2741634.04

16.42

Cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 40 mm

nominal size) in pavements, laid to required

slope and camber in panels as required

including consolidation finishing and tamping

complete.

605.48 cum 5503.80 3332465.87

16.43

"Providing and laying design mix cement

concrete of M-30 grade, in roads/ taxi tracks/

runways, using cement content as per design

mix, using coarse sand and graded stone

aggregate of 40 mm nominal size in appropriate

proportions as per approved & specified design

criteria, providing dowel bars with sleeve/ tie

bars wherever required, laying at site, spreading

and compacting mechanically by using needle

and surface vibrators, levelling to required slope/

camber, finishing with required texture, including

steel form work with sturdy M.S. channel

sections, curing, making provision for

contraction/ expansion, construction &

longitudinal joints ( 10 mm wide x 50 mm deep)

by groove cutting machine, providing and filling

joints with approved joint filler and sealants,

complete all as per direction of Engineer-in-

charge (Item of joint fillers, sealants, dowel bars

with sleeve/ tie bars to be paid separately).

Note:- Cement content considered in M-30 is @

12 16.43.2

Cement concrete manufactured in automatic

batching plant (RMC plant) i/c transportation to

site in transit mixer

1210.97 cum 7160.40 8671023.14

16.44

Extra for providing and mixing hardening

compound of approved quality as per

manufacturer's specification in cement concrete.968.78 litre 46.45 44999.61


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

16.45

Providing and fixing in position pre-moulded joint

filler in expansion joints.

2665.98

per cm

depth per

cm width

per m

length

2.20 5865.16

16.46Providing and laying in position bitumen hot

sealing compound for expansion joints etc.

16.46.1

Using grade 'A' sealing compound.

2665.98

per cm

depth per

cm

width per

m length

2.20 5865.16

12.50

Providing and fixing precoated galvanised iron

profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-charge)

0.50 mm (+ 0.05 %) total coated thickness with

zinc coating 120 grams per sqm as per IS: 277,

in 240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and polyester

top coat 15-18 microns. Sheet should have

protective guard film of 25 microns minimum to

avoid scratches during transportation and should

be supplied in single length upto 12 metre or as

desired by Engineerin- charge. The sheet shall

be fixed using self drilling /self tapping screws of

size (5.5x 55 mm) with EPDM seal, complete

upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

2943.23 sqm 550.40 1619951.59

10.2

Structural steel work riveted, bolted or welded in built

up sections, trusses and framed work, including

cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer all complete.

35318.71 kg 67.60 2387544.93

13.61Painting with synthetic enamel paint of approved

brand and manufacture to give an even shade :

13.61.1 Two or more coats on new work 8829.68 sqm 78.40 692246.76

PAINTING ROAD / RUNWAY MARKING

16.47

Painting runway/taxi track/apron marking with

adequate nos of coats to give uniform finish with

road marking paint of superior make as

approved by the Engineer-in-charge, i/c cleaning

the surface of ail dirt, scales, oil, grease and

other foreign mater;al etc. and lining out

complete.13 16.47.1 New work (Two or more coats) 6054.85 sqm 104.90 635153.29

14 16.49

Making bell mouth opening/ entrance of size

100x50x50 cm for drainage pipe under footpath,

including providing cement concrete 1:3:6 (1


aggregate 20 mm nominal size) for shape of bell

mouth, including plastering providing and fixing

precast R.C.C./ S.F.R.C. slab including

plastering with cement mortar 1:3 (1 cement : 3

fine sand) of 6 mm thickness on exposed

surface of the slab & bell mouth including

centring, shuttering & neat cement punning

inside the bell mouth etc. all complete.

10.00 each 1829.70 18297.00


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

15 16.68

Providing and laying 60mm thick faciory made

cement concrete interlocking paver block of M -

30 grade made by block making machine with

strong vibratory compaction, of approved s;ze,

design & shape, laid in required colour and

pattern over and including 50mm thick

compacted bed of coarse sand, filling the joints

with line sandetc. all complete as per the

direction of Engineer-in-charge.

2264.02 sqm 615.70 1393957.11

16 16.69

Providing and laying at or near ground level

factory made kerb stone of M-25 grade cement

concrete in position to the required line, level

and curvature, jointed with cement mortar 1:3 (1

cement: 3 coarse sand), including making joints

with or without grooves (thickness of joints

except at sharp curve shall not to more than

5mm), including making drainage opening

wherever required complete etc. as per direction

of Engineer-in-charge (length of finished kerb

edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved by

Engineer-in-charge).

129.01 cum 5012.65 646682.57

19.6

Providing and laying non-pressure NP2 class

(light duty) R.C.C. pipes with collars jointed with

stiff mixture of cement mortar in the proportion of

1:2 (1 cement : 2 fine sand) including testing of

joints etc. complete :17 19.6.2 150 mm dia. R.C.C. pipe 285.60 metre 356.70 101873.52

TOTAL of ROAD WORKS) 28419208.91 0.00

ROAD SIDE DRAIN WORK

6.1

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in foundation

and plinth in:

18 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 337.25 cum 4751.65 1602477.19

4.1

Providing and laying in position cement concrete

of specified grade excluding the cost of

centering and shuttering - All work up to plinth

level :

19 4.1.21:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3


20 4.1.101:5:10 (1 cement : 5 coarse sand (zone-III): 10


13.4 12 mm cement plaster of mix :21 13.4.1 1:4 (1 cement: 4 coarse sand) 4477.07 sqm 180.85 809677.94

22 13.18 Neat cement punning. 2238.53 sqm 42.60 95361.57

23 23.9

Providing and fixing factory made precast RCC

perforated drain covers, having concrete of

strength not less than M-25, of size 1000 x

450x50 mm, reinforced with 8 mm dia four nos

longitudinal & 9 nos cross sectional T.M.T. hoop

bars, including providing 50 mm dia perforations

@ 100 to 125 mm c/c, including providing edge

binding with M.S. flats of size 50 mm x 1.6 mm

complete, all as per direction of Engineerin-

charge.

2273.00 each 959.35 2180602.55

TOTAL ( ROAD SIDE DRAIN WORK) 5114272.99 0.00


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

HORTICULTURE WORK

2.4

Supplying and stacking at site dump manure

from approved source, including carriage upto 5

km complete (manure measured in stacks will

be reduced by 8% for payment) :

242.4.1

Screened through sieve of I.S. designation 20

mm2567.72 cum 170.70 438309.68

25 2.9

Mixing earth and sludge or manure in the

required proportion specified or directed by the

Officer-in-charge

2567.72 cum 21.35 54820.81

2.10

Grassing with selection No. 1 grass including

watering and maintenance of the lawn for 60

days or more till the grass forms a thick lawn,

free from weeds and fit for mowing including

supplying good earth, if needed (the grass and

earth shall be paid for separately).26 2.10.1 In rows 5 cm apart in both directions 12838.60 Sqm 10.40 133521.40

27 2.11

Renovating lawns including weeding, cheeling

the grass, forking the ground, top dressing with

sludge or manure, mixing the same with forked

soil, watering and maintaining the lawn for 60

days or more till the grass forms a thick lawn

free from weeds and fit for mowing and disposal

of rubbish as directed, including supplying good

earth if needed but excluding the cost of sludge

or manure (The manure/sludge shall be paid for

separately).

12838.60 Sqm 20.15 258697.72

28 2.13

Preparation of beds for hedging and shrubbery

by excavating 60 cm deep and trenching the

excavated base to a further depth of 30 cm,

refilling the excavated earth after breaking clods

and mixing with sludge or manure in the ratio of

8:1 (8 parts of stacked volume of earth after

reduction by 20% : one part of stacked volume

of sludge or manure after reduction by 8%),

flooding with water, filling with earth if necessary,

watering and finally fine dressing, leveling etc.

including stacking and disposal of materials

declared unserviceable and surplus earth by

spreading and leveling as directed, within a lead

of 50 m, lift up to 1.5 m complete (cost of

sludge, manure or extra earth to be paid for

separately)

2567.72 cum 130.35 334702.21

TOTAL ( HORTICULTURE WORK) 1220051.83 0.00

MISS. WORK

98 MR

Providing & fixing Chicken wire mesh on joints

of RCC & Brick work before plastering complete

in the direction of Engineer-in-charge.1700.12 sqm 131.00 222715.66

MR

RCC Core cut : Drilling with core cutting

machine in RCC beams,slabs,floorsetc.,for

laying pipes and rendering the same in RCC

1:2:4 finishing the same to the satisifaction of

the owner or his authorised representative

etc.,including nominal reinforcement wherever

required,complete,at all levels The quote shall

also include for providing EPOXY based water

proofing compound for sealing the joints around

the pipes upto any depth at all heights & levels.

99 A)100mm dia. (At All Floor) 348.00 no's 465.00 161820.00

100 b)200mm dia. (At All Floor) 348.00 no's 581.00 202188.00


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

101 MR

Self Leveling Compound

Providing & Laying of 2 - 3 mm average thick

layer of cementations smoothening compound

of ARDEX CL-11 or equivalent as

recommended by the Vinyl sheet flooring

manufacturer over and including a priming

compound of P-51 or equivalent as

recommended by the Vinyl sheet flooring

manufacturer and installation team on concrete

surface to provide a smooth & homogenous

surface for laying of vinyl sheet flooring

complete to the entire satisfaction of Engineer-in-

charge

276.44 sqm 568.00 157018.49

FOR OT AREA- CONDUCTIVE

Supply and installation of PASTELL Conductive

Vinyl Sheet Flooring manufactured by Armstrong

or equivalent World Industries, Inc, 1.83m wide,

having a nominal total thickness of 2.2mm. The

nominal thickness of the wear layer would be 2

mm. The product should have a conductive

backing of 0.2mm. The wear surface shall

consist of impregnated polyurethane

homogeneous mixture of PVC, Plasticizers,

Urethane, color pigments and filler calendared to

form a sheet. Colors and pattern detail shall be

dispersed throughout the thickness of the wear

layer. PASTELL Conductive shall conform to

Group P of Wear Resistance as per EN 649,

Flammability of class Bfl-s1 as per EN 13501-1,

Slip resistance of R9 as per BGR 181, Dynamic

Coefficient of friction as DS as per EN 13893,

Impact sound reduction of 3 dB as per EN ISO

140-8,

102

Residual indentation of 0.05 mm as per EN

433, Color fastness rating ≥6 as per ISO 105-

B02, Vertical resistance(R1) less than 106Ω as

per EN 1081, Static electrical charge of ≤2.0kV

as per EN 1815, Thermal resistance of

0.01m²K/W as per EN 12667, Thermal

conductivity of 0.25 W/mK as per EN 12524.

PASTELL conductive shall exhibit ESD

properties as following - Vertical resistance less

than 3.5x10^6Ω as per EN 61340-4-1, Static

electrical charge - system test less than 100V as

per EN 61340-4-5.The class of use of PASTELL

Conductive is 23/34/43 as per EN 685.

113.25 sqm 2892.00 327504.54

103 NSR

ROLLER BLINDS

Providing and fixing Roller Blinds with roller

tube, bottom bar leveller made of extruded

aluminium alloy an Idler, Insert Type- Brackets,

powder coated PVC chain etc. all complete at all

floor and heights as per approved manufacturer

specification .


Sl.

No.

DSR 2016


TOTAL DSR

AmountNDSR Rate

TOTAL NDSR

Amount

Roller Tube Control, Clutch, Idler

Side by side or single Roller Tube of extruded

Aluminium alloy 6060-T66-EN755 with powder

coated (50 micron thickness) 38- 41mm outer

dia minimum wall thickness of 1.6mm having in

built spring-clutch system. Clutch shall be made

of carbon steel spring wrapped by means of a

high strength fiberglass reinforced polyester

assembly to transmit motion from driving to

driven members of clutch mechanism. Clutch

shall operate bi- directionally with the use of an

endless PVC bead chain.Clutch mechanism

shall be crash proof, prevent slippage and shall

raise and lower smoothly to any desired height.

Clutch shall never need any adjustment. Idler

shall be of high strength fiberglass reinforced

polyster,consisting of an outside sleeve and

centre shaft. Sleeve shall provide bearing

surface for roller tube and rotate freely on centre Brackets-Insert Type-Fit with Roller Tube

Ceiling or side mounting brackets shall be of

made up of stainless steel of grade 304 and

powder coated with 50 micron thickness.

Bottom Rail

Bottom of the blind shall be provided with

extruded aluminium tube having weight 390

gm/meter in round/oval/ square shape fitted with

end caps powder coated (50 micron thickness)

in desired colour matching to the fabric. The

fabric shall be enclosed in the suitably created

pocket along with the tube.

PVC Ball Chain

The Control Unit and powder coated PVC Chain

with a Ball Pitch of no lesser than 6.5mm consist

of bead chain, bead chain stop, Tension device

and bead chain connector pully ito match the

fabric shall be provided to ensure an enduring

operation alongwith an aesthetic value.

ROLLER BLIND FABRIC SPECIFICATION

Roller blind fabric made up of 25% Polyester

and 75% PVC. Lead free fabric with 5%

opening, thickness of 0.91mm, with UV

Blockage of 95%, Solar Reflectance of 62%,

solar absorption of 16%, solar transmittance

22%, acoustical value NRC-0.10/SAA-0.09

having Greenguard Gold certification for low

chemical emissions, Bacterial and Fungal

Resistance as per ASTM E 2180, ASTM G21,

AATCC30 part 3, ASTM D 3273, Greenguard.

Mold and Bacterial standard ASTM 6329, with

Microban anti- microbial protection. Flame

retardant as per California US Title 19(Small

Scale), NFPA 701-2004 TM#1 (small scale),

NFPA 101 (Class A rating), IBC section 903.1

(Class A rating), BS 5867 2008 Part 2 Type B

Performance, CAN/ULC-S-109-03 (large and

small scale) and CAN/CGSB2-4.162-M80, STM

E 84(Class 1) NFPA 701 TM#2 (large scale)

with 10 years of interior warranty. Make Phifer

USA

1019.88 sqm 2926.00 2984168.88

NSRExtra thickness of mortar for maching flooring

diffrance in tile & kata stone4831.43 sqm 60.00 289885.73

TOTAL MISS. WORK) 0.00 4345301.29

Total 415947579.20 4345301.29

Grand Total 420292880.49


Sr no.

DSR-

2016

Code

DESCRIPTION QTY UNIT RATE AMOUNT

1 EQUIPMENT

1.1 WATER COOLED SCREW CHILLER

Supply,Installation, Testing and commissioning of imported

best efficiency factory designed and pre-fabricated Vapor

Compression screw water chilling machines with variable

frequency drive (VFD) starter,including one or more

horizontal/vertical,Open type /hermatic/semihermetic type

compressors. , of twin screw type , equipped with even pass

water cooled condenser of shell and tube type as per the

specifications as detailed earlier in the document.The

compressor motor shall be suitable for VFD operations on 415

+/- 10% Volts , 3 Phase , 50 Hz., and shall be direct coupled

type .The chiller shall be even pass & Flooded type complete

insulated with approved insulating masterial , Refrigerant

piping shall be factory assembled as per the specifications

detailed in the related section , or as per the specifications of

the approved vendor , whichever is more stringent.

The chiller assembly will be delivered with the charge of the

refrigerant and compressor oil Gauge panel, drive package,

VFD Starter, control panel and associated wiring,BMS Card

and all other accessories to make the chiller package ready

for installation and commissioning., and most efficient NPLV

of less than 0.39 IKW/TR.

The various other parameters governing the selection and

capacity computations of the chiller package are as follows:

Condenser water in : 90 Deg F , Condenser water out : 97.5

Deg F , Fouling Factor : 0.001 FPS

Chilled water in : 54 Deg F , Chilled water out : 44 Deg F ,

Chiller Fouling factor : 0.0005 FPS

COP @ Conditions: Shall be as per latest relevant ECBC

standards. ( Minimum 5.4 COP)

Power Consumption @ Full Load at tender conditions: Shall

not be more than or equal to 0.75 Ikw/TR.

NPLV: Shall be less than 0.39 Ikw/TR. Procedure for

calculations shall be as per AHRI guidelines.

Installation, Testing and commissioning of factory designed

and pre-fabricated Vapor Compression refrigeration water

chilling machines of following actual capacity as described

above and in the specifications.The refrigerant acceptable is

R -134A .

1.1.1100 TR Actual Capacity water cooled screw type chiller

(2#Working +1# Standby)3 No. 2,419,313.00 7,257,939.00

CIF, Bhillai (Chhatisgarh)

Customs duty, CVD, Auxiliary duty

Clearing, port handling and other incidental charges.

Loading, Local transportation and all other incidental charges

upto delivery at site.

PROJECT: PROPOSED 100 BED ESIC HOSPITAL AT BHILAI, CHHATTISGARH

HVAC Work BOQ


Sr no.

DSR-

2016

Code


Installation, testing and commissioning

1.2 Hot water generator

Supply Installation,testing and commissioning of Hot water

generator as per specifications .

Inlet Water Temperature 50 °C

Outlet Water Temperature 55 °C

1.2.1200.0 KW Hot water generator (with multiple circuit) (1

Working + 0 Standby)1 No. 290,318.00 290,318.00

1.3 PUMP SETS

1.3.1 CONDENSER WATER PUMPS

Supply,installation,testing and commissioning of horizontal

End Suction/split casing centrifugal pumps for condenser

water recirculation , complete with TEFC squirrel cage

motors, base plate, and all necessary accessories.Capacity of

pump sets , nett head is as given below:All the pumps

mentioned below shall also be complete with mechanical

seals, and drain connections , and shall be suitable for

operation on 415+/- 10 % Volts , 50 Hz , 3 Phase AC power

supply.

a. 400 USGPM * 25 M for Screw chiller, (2Working + 1Standby) 3 No. 169,493.00 508,479.00

1.3.2 PRIMARY CHILLED/HOT WATER PUMPS (FIXED SPEED)

Primary circuit:Supply, installation, testing and

commissioning of end suction/monoblock centrifugal pumps

for chilled water/Hot Water recirculation, complete with

TEFC squirrel cage motors, base plate, and all necessary

accessories. Capacity of pump sets, nett head is as given

below: All the pumps mentioned below shall also be complete

with mechanical seals, and drain connections, and shall be

suitable for operation on 415±10% Volts, 50 Hz, 3 Phase AC

power supply.

a.240 USGPM * 15 M for primary Chilled/Hot water circuit

(2Working + 1Standby)3 No. 105,523.00 316,569.00


Sr no.

DSR-

2016

Code


1.3.3 VARIABLE SPEED PUMPING SYSTEM

Supply, installation, testing and commissioning of centrifugal

end suction pumps factory mounted on a common base with

electric motor for re circulation of water for the central air

conditioning system.. The pump motor shall be suitable for

415± 10% volts, 50 cycles, 3 phase AC power supply.

Secondary chilled water pumps shall be suitable for operation

on adjustable frequency drives .Secondary Variable Speed

Pumping System consisting of 3No.’s adjustable frequency

drives (one dedicated for each pump)( 1 # provision for

future), 1 No. Microprocessor based Pump Logic Controller

for controlling 2 working +1(stand-by) pumps in parallel , 1

No. Flow Sensor / Transmitter, & 3 No.’s Diffrential Pressure

sensors / Transmitters.

The Pump Logic Controller shall be capable of accepting

analog inputs from Flow Sensor / Transmitter & from Kw

Sensor / Transmitter to provide lowest Kw draw based on

Efficiency Optimisation Program & multiple differential

pressure sensor / transmitters. Controller shall be capable of

accepting input from flow sensor transmitter,to ensure end of

the curve protection.

The system shall be complete in all respects and suitable for

following ratings and duty.

a.240 USGPM * 25 M for Chilled/hot water circuit (2Working +

1Standby)3 No. 213,233.00 639,699.00

1.4 COOLING TOWERS

Supply, installation , testing and commissioning of Vertical

Induced draft or cross flow design cooling towers , in

accordance with the specifications laid out earlier in this

document under the related chapter, and in accordance with

BS-4485.The cooling tower shall be of FRP construction ,

complete with sump and aluminum ladder , isolating switch

and other accessories to make it fully operational and

maintainable.The maximum allowable sound power at a

distance of 3 M from the fan shall be up to 80 DB(A). The

cooling tower model shall be selected to suit site conditions.

Entering water temperature :97°F, Leaving water temperature

: 90°F.

Type of fan : Propeller .Type of motor : 710 RPM , Weather

proof.

a.

Water Flow rate : 400 USGPM , 125 TR (Based on Ludhiana

ambient condition: Max WB 83 Deg F, Approach of 7 Deg F) ,

cooling tower blower fan or motors (cooling tower 2w+ 0S)

2 No. 235,923.00 471,846.00


Sr no.

DSR-

2016

Code


1.5 AIR HANDLERS (With One Coil System)

Supply, installation testing and commissioning of factory built

floor mounted chilled water Double skin type

horizintal/vertical air handling units made of 25mm ±2mm

thick panels consisting of pre plasticized GI casing of thickness

0.8mm outside layerand 0.8mm inside layer with

polyurethene foam (PUF) insulation factory injected between

them by injection moulding machine, complete with blower

section with blower suitable for static pressure as required ,

min. 2 bend GSS/PVC eliminators, cooling coil section with

aluminium finned copper tubes ( tube thickness not less than

0.5 mm ) cooling coil of 6 row deep, filter section with 50 mm

thick metal viscous filter /washable synthetic type air

prefilters, belt drive/ direct driven package with TEFC drive

motor of efficiency class IE3 suitable for 415±10% V, 50Hz, 3

phase AC supply suitably designed for variable frequency

drive applications, drain connections , stainless steel (18G)

drain pain with PUF insulation,150 mm dia. dial type pressure

gauges (2 Nter two days of proper curing applying a

second coat of cement slurry using 2.75 kg/ sqm of cement

admixed with water proofing compound conforming to IS :

2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick joi

Supply , installation testing and commissioning of Double skin

floor mounted Horizontal/vertical Two pipe system (One coil)

AHUs as per the mentioned in AHU schedule. (All AHU

Should Be BMS/VFD Compitable)

Note: If AHU With fine filter or Fine and Hepa Filter than

these filters with sections shall be separate considerable as

defined below in this boq item no. 4.11.

a 16.26.6

Double skin floor mounted Horizontal two pipe system (one

coil)AHU 6500 CFM / 12.0 TR, 6 row deep chilled water coil ,

pre & Fine filter, 80 mm SP WG with three phase motor and

Mixing Box . (For MRI , GF)

1 No. 163,967.00 163,967.00

b 16.26.3

Double skin Ceiling mounted Horizontal two pipe system

(one coil)AHU 4000 CFM / 7.5 TR, 6 row deep chilled water

coil , pre & fine filter and Mixing Box, 65 mm SP WG with

three phase motor , (For CT Scan, GF)

1 No. 100,009.00 100,009.00

c 16.26.1




three phase motor , (For Triage, GF)

1 No. 75,410.00 75,410.00

d 16.26.1




three phase motor , (For Observation, GF)

1 No. 75,410.00 75,410.00


Sr no.

DSR-

2016

Code


e 16.26.1




three phase motor , (For Minor OT, GF )

1 No. 75,410.00 75,410.00

f 16.26.4




Mixing Box . (For Pathology , 1st)

1 No. 124,770.00 124,770.00

g 16.26.3




three phase motor , (For Blood Bank,1st )

1 No. 100,009.00 100,009.00

h 16.26.1




Mixing Box . (For Dialysis , 2nd)

1 No. 75,410.00 75,410.00

i 16.26.1




three phase motor , (For Cath Recovery,2nd )

1 No. 75,410.00 75,410.00

j 16.26.1



coil , pre & Fine filter, 65 mm SP WG with three phase motor

and Mixing Box . (For Cath Lab , 2nd)

1 No. 75,410.00 75,410.00

k 16.26.1




and Mixing Box . (For Delivery,Recovery,Nursery Room , 3rd)

3 No. 75,410.00 226,230.00

l 16.26.3




. (For Labour Room, 3rd)

1 No. 100,009.00 100,009.00

m 16.26.4



coil , pre filter, 35 mm SP WG with three phase motor and

Mixing Box . (For LabourRecept. , 3rd)

1 No. 124,770.00 124,770.00

n 16.26.7




Mixing Box,weather proof canopy . (For ICU , 3rd)

1 No. 182,033.00 182,033.00

o 16.26.6




Mixing Box,weather proof canopy . (For Recovery Beds , 3rd)

1 No. 163,967.00 163,967.00


Sr no.

DSR-

2016

Code


p 16.26.8




Mixing Box,. (For Sterile Corridor , 3rd)

1 No. 199,212.00 199,212.00

1.6Floor Mounted Horizontal Air Handling Units With Exh.

Blower and Enthalpy Recovery Wheel (FM AHU)

Supply, Installation Testing and Commissioning of floor

mounted AHU's. The AHU's shall be double skin type made of

0.60 mm thick GI sheet with 23+/-2mm for indoor application

and 43+/-2 mm Thick for outdoor application PUF insulation.

The Drain Pan for AHU's shall be of SS. They shall be suitable

for indoor/outdoor installation. The AHU's selected shall be

supplied with Forward / Backward direct driven/belt driven

supply air Blower Fans and exh. air blower with Ethalpy

Recovery Wheel (Min. Efficiency of HRW is 75%) (ERW/HRW)

suitable to deliver the undergiven CFM and Static. The AHU's

shall be chilled water coil ( complete with mixing chamber if

required and electrical push buttnos. Cooling Coil)on starting

panel for operating the AHU. AHU Included VI Pads .

All AHU Should Be included Supply/Return/Fresh Air Damper

& Thermal Break Profile and with three phase motor suitable

for VSD drive and BMS Compitable

a

Double skin floor mounted Horizontal 8-Row Depth chilled

water Coil (1 Coil) with Supply Fan 1600 CFM with pre, fine

and Hepa filter on terminal, S.P. is 115 mm & Exhaust fan

2000 CFM with Pre & HEPA Filter, S.P. 80 mm , Heat Recovery

Wheel (Enthalpy Wheel) AHU Coil is 5.0 TR, pre filter with

mixing box & Weather Proof Canopy. (For Isolation Room,

2nd Floor)

1 No. 381,150.00 381,150.00

b






mixing box & Weather Proof Canopy. (For OT-1,3, 3rd Floor)

2 No. 658,845.00 1,317,690.00

c






mixing box & Weather Proof Canopy. (For OT-2, 3rd Floor)

1 No. 658,845.00 658,845.00


Sr no.

DSR-

2016

Code


1.7 FAN COIL UNITS (Standard)

Supply,Installation , testing and commissioning of fan coil

units of specified capacities and air flow as per the

specifications , complete with auxillary drain pan.

Fan coil unit shall be supplied with approved make of factory

fitted adequately sized insulated (with nitrile foam) two way

motorized valves , insulated ball valves-one with Y strainer,

and the other without Y strainer complete with room

thermostat for fan speed control , associated conduiting and

wiring between the thermostat , 2 - way valve .etc.

Cost of fan coil unit shall be inclusive of approved make room

thermostat (heatig and cooling, with fan speed control), and

associated wiring etc.between the thermostat and two way

valve , for a standard length of approximately 5-7 M per fan

coil unit.

Providing and fixing in position the following Fan Coil

units complete with all valves and accessories as described

above.

a 1.5 TR nominal capacity ( 600 CFM) 1 No. 17,969.00 17,969.00

b 2.0 TR nominal capacity ( 800 CFM) 3 No. 20,147.00 60,441.00

c 2.5 TR nominal capacity ( 1000 CFM) 8 No. 22,325.00 178,600.00

d 3.0 TR nominal capacity ( 1200 CFM) 8 No. 24,503.00 196,024.00

1.8 Propeller fan

Supply,installation,testing and commissioning of Propeller fan

of the following capacity of approved make and specification.

Fan shall be supplied with aluminum gravity louver & bird

screen and Speed Regulator.

a 150 mm dia propeller fan, with single phase motor 7 No. 2,995.00 20,965.00

b 300 mm dia propeller fan, with single phase motor 9 No. 3,321.00 29,889.00

c 450 mm dia propeller fan , with single phase motor 1 No. 3,975.00 3,975.00

1.9 Inline fan

Supply, installation, testing and commissioning of Circular

swing type Inline fan with fiire retardent Canvas connection

of the following capacity of approved make and specification.

a 100 to 300 CFM, 5-7 mm SP WG with Single phase motor 6 No. 6,580.00 39,480.00

b 400 to 500 CFM, 7-10 mm SP WG with Single phase motor 11 No. 6,580.00 72,380.00

c 600 CFM, 10-12 mm SP WG with Single phase motor 6 No. 8,168.00 49,008.00

d 700 to 800 CFM, 10-12 mm SP WG with Single phase motor 40 No. 9,257.00 370,280.00

e 900 CFM, 12-15 mm SP WG with Single phase motor 8 No. 12,315.00 98,520.00

f 1000 CFM, 12-15 mm SP WG with Single phase motor 1 No. 15,019.00 15,019.00


Sr no.

DSR-

2016

Code


1.10 FAN SECTIONS/ Cabinet fan :

Supply,Installation ,Testing and commissioning of approved

make of ventilation AMCA Certified Cabinet Fan of Double

SKIN CONSTRUCTION, belt driven centrifugal fan ,mounted on

floating foundation of spring mounted vibration isolators ,

and canvass connection , squirrel cage induction motor ,

mounted within the housing , and all other details as called

for in the drawings , specifications. Fan section shall be

suitable for floor / ceiling mounted application as detailed in

the drawings).The fan motor shall be suitable for operation

on Single speed , 415 ± 15 Volts, 50Hz,AC power supply.

Ventilation fan sections of single skin construction as

described above and in the specifications DIDW type,motor

within the casing.All fans shall have single speed motors Cost

to be inclusive of unit isolator.

a

800 CFM, 3PH/4P, 80 mm WG static pressure with VSD

compatible motor suitable for floor/Ceiling mounted

application.(For OT Scrub Exhaust )1 No. 44,105.00 44,105.00

1.11 Tube Axial Flow fans

SITC of Tube axial flow fans, as per specifications and

approved makes suitable for three phase operation at 1450

RPM respectively Normal/Smoke case.

AMCA Certified tube axial flow fans complete with all

accessories, suitable for wall mounted / ceiling suspended

installation. The fan shall be supplied with suitable 3PH/2P

motor at 2960 RPM , and shall be selected for 30 mm static

pressure (WG), (F Class motor insulation) All fan with fiire

retardent Canvas connection.(For Smoke make up air) Fans

capacity as per below mentioned as: (As per Vent. Fan

Schedule)

a 3000 CFM (For Hospital Liftwell Pressurization) 2 No. 39,749.00 79,498.00

b 5000 CFM (For Residential Liftwell Pressurization) 1 No. 46,283.00 46,283.00

c 16000 CFM (For Residential Liftlobby Pressurization) 1 No. 85,487.00 85,487.00

1.12 Evaporative air cooler(Air Washer)

Supply , Install, test and commission double skin Evaporative

air washer as per specifications , suitable for the following

capacity given below at 75-90% efficiency of evaporative

medium. The fan shall be of DIDW centrifugal construction.

Packaged Type

Ventilation fan sections of double skin construction as

described above and in the specifications DIDW type,motor

within the casing.All fans shall have multi speed motors Cost

to be inclusive of unit isolator and .25HP-0.5HP water pump.

Fan Motor VFD Compitable. AS PER SPEC.

a

12500 CFM, 3PH, 40 mm WG static pressure,960 rpm, 1.5HP

motor with Speed controller for floor mounted with weather

proof canopy

1 No. 174,240.00 174,240.00


Sr no.

DSR-

2016

Code


1.13 Air Scrubber (Wet Type)

Supply , Install, test and commission air Scrubber of

approved make and specifications. (The scrubber will be of

the similar construction as that of the double skin air

washer,except for that the system shall have the following

exceptional features: BACKWARD CURVED DIDW FAN, spray

bank comprising of brass nozzles - instead of the cellulose

pad evaporative medium , expanded viscous metal filters )

a 15000 CFM 80 mm sp for Kitchen Exh. 1 No. 206,910.00 206,910.00

1.14 AIR DIFFERENTIAL PRESSURE SWITCH

Supply,install,test and commission Air Differential pressure

switches complete with sensor probe , etc. integrated with

Light and visual alarm signal, as per general details and

specifications and approved make.To be installed across HEPA

filter bank sections and Operating rooms.The necessary

control and power wiring shall be in the scope of the

contractor.

aAir Differential Pressure Switch. ( ACROSS OT & Isolation

rooms.)6 Set 5,479.00 32,874.00

1.15 Temperature and RH sensor and adjuster package.

Supply,install-(grout),test and commission micro-processor

based Room temperature , humidity sensor and remote

adjuster package within a MS housing -wall ,suitable for

mounting, and having a stainless steel cover plate.This

package shall have a temperature and humidity display - red

2" high LED character for operation rooms , and other critical

areas.

a

Sensor, adjuster (Snap acting humidistat/Proportional

thermostat- Microprocessor based) and displayer package, as

described above.

4 Set 19,602.00 78,408.00

1.16 Pan Type humidifier and humidistat

a Supply, install, test and commission snap acting humidistat . 3 No. 13,122.00 39,366.00

bSupply, install, test and commission wall / floor mounted Pan

Type Humidifier package of following capacities.

b1 4.0 KW 3 No. 35,578.00 106,734.00


Sr no.

DSR-

2016

Code


1.17 Variable speed drives.

Supply of following HVAC dedicated VFDs with IP 20

enclosures , complying with the tender specifications and

having:

1. built-in dual 5% impedance DC link reactor (harmonic

filters) on the positive and negative rails of the DC bus of the

VFD.

2. built-in EMC Filters (electromagnetic compatibility filters)

for for VFDs for restriction of conducted emissions to comply

with IEC61800: 3 (unrestricted distribution):2004 Category C

3,

3. Three-feedback PID controller having capability to

simultaneously accept 3 feedback signals from temperature

sensors or pressure sensors or CO2 sensors for process

optimization and accordingly regulate the speed of the AHUs

or pumps.

4. Provision for additional 3 PID controllers to control external

devices such as chilled water modulating valve, fresh air

damper, etc. thus reducing the number of I/Os in DDC

Controllers & improving system reliability.

5. Automatic Energy Optimization / Load dependent flux

optimization functionality for maximum energy savings.

6. MODBUS RTU as the communication protocol between

BMS & VFDs.

7. VFDs not meeting above requirements shall provide

external disconnect, additional external EMC Filters to comply

with IEC61800: 3 (unrestricted distribution):2004 Category C 3

(50 m), external PLCs / DDCs to achieve 3 Feedback PID

a

Supply , Install, test and commission Variable Speed Drive

package as described above and in specifications suitable for

for 1.5 kW motor rating as per the specifications(3 Phase

variable frequency output for OT's AHU Scrub Exh. Fan,

Isolation AHU and Exh.. These variable speed drives shall get

the input from the remote air differential pressure adjuster ,

as described above in item.

3 No. 27,225.00 81,675.00

b




variable frequency output for OT's AHU and Exh.. These

variable speed drives shall get the input from the remote air

differential pressure adjuster , as described above in item.

4 No. 33,215.00 132,860.00

c




variable frequency output for OT's AHU and Exh.. These

variable speed drives shall get the input from the remote air

differential pressure adjuster , as described above in item.

2 No. 41,927.00 83,854.00

TOTAL (EQUIPMENT) 16,124,815.00


Sr no.

DSR-

2016

Code


2 Chilled water Piping , Valves & Accessories (Including Insulation)

2.1 EXPANSION TANK

Supply, Installation ,Testing and commissioning of Open

expansion tank as per the specifications detailed earlier in

the relevant section .The Open vessel expansion tank shall be

complete with all accessories so as to make it ready for

installation and commissioning on site.The tank shall be

insulated with the approved method of insulation , and shall

be complete with water make-up connection and system

.The expansion tank will be supplied,Non return Valve and

interconnecting piping.

a1000 Ltr . Open Expansion Tank duly insulated and with all

accessories.1 No. 40,896.00 40,896.00

2.2 CHILLED WATER PIPING (Including Nitrile Rubber Insulation)

Providing and fixing in position the following MS C

class chilled water piping , cut to required length, and

installed with welded joints (USE RECTIFIER AS SPECIFIED),

including all necessary fittings such as elbows , tees , etc.and

confirming to the specifications as detailed in the relevant

chapter in the document. Pipes will be accepted in order of

preference (Factory fabricated / Fabricated out of 7mm thick

plates duly rolled in a workshop and welded : for pipes

beyond 350mm dia)

Chilled water pipes shall be insulated with 19/32 mm thick

closed cell elastometric Nitrile rubber of min. 45 kg/m3

density, thermal conductivity 0.037w/mk or better at 20°

mean temp. class'O' insulation applied by suitable adhesive

complete including repairing of damage to building etc. for

chilled water piping as per specifications (Above nitrile foam

2 coat layer 7 mile cloth star bond/Insu sound insulation)

Note: The pipes of sizes 150mm & below shall be M.S. 'C'

class as per IS:1239 and Pipes size above 150 mm shall be

welded black steel pipe heavy class as per IS: 3589, from

min. 6.35 mm thick M.S. sheet for pipes up to 350 mm dia.

And from min. 7 mm thick MS sheet for Pipes of 400 mm

dia. and above.

Insulation specification and finishing material remains same

for the valves and drain pipes as per specifications.

a 16.2.7 125mm dia (32mm thick insulation) 10 RM 2,142.00 21,420.00

b 16.2.8 100mm dia (32mm thick insulation) 80 RM 1,709.00 136,720.00

c 16.2.9 80mm dia (32mm thick insulation) 100 RM 1,255.00 125,500.00

d 16.2.10 65mm dia (32mm thick insulation) 110 RM 1,030.00 113,300.00


Sr no.

DSR-

2016

Code


e 16.2.11 50mm dia (32mm thick insulation) 100 RM 881.00 88,100.00

f 16.2.12 40mm dia (32mm thick insulation) 180 RM 702.00 126,360.00

g 16.2.13 32mm dia(19mm thick insulation) 220 RM 564.00 124,080.00

h 16.2.14 25mm dia (19 mm thick insulation) 200 RM 463.00 92,600.00

2.3CHILLED WATER PIPING (Including resin bonded fiber

glass/EPS Insulation)

Providing and fixing in position the following MS 'C' class

chilled water piping, cut to required length, and installed with

welded joints (USE RECTIFIER AS SPECIFIED), including all

necessary fittings such as elbows, tees, etc. and confirming to

the specifications as detailed in the relevant chapter in the

document. Pipes will be accepted in order of preference

(Factory fabricated / Fabricated out of 7mm thick plates duly

rolled in a workshop and welded : for pipes beyond 350mm

dia)

Chilled water pipes shall be insulated with fire retardent

quality expanded polystrene moulded pipe section of density

20 kg/cum. after a thick coat of cold setting adhesive(CPRX

compound) wrapping with 500g polythene faced hessain and

finally applying 0.63 mm aluminium sheet cladding complete

with type 3, grade 1 roofing feltstrip (As per IS:1322 as

amended up to date)at joint and repairing of damage to

building etc. for chilled water piping as per specifications with

Supproting Arrangement or paddestal on Terrace/ In shafts.






dia. and above.

Insulation specification and finishing material remains same

for the valves and drain pipes as per specifications.

a150mm dia (75 mm thick insulation) with sand cement

plaster in tunnel/under ground250 RM 3,514.00 878,500.00

b 16.3.6 150mm dia (75 mm thick insulation) 130 RM 2,779.00 361,270.00

c 16.3.7 125mm dia (50 mm thick insulation) 30 RM 2,330.00 69,900.00

d 16.3.8 100mm dia (50 mm thick insulation) 160 RM 1,981.00 316,960.00

e 16.3.9 80mm dia (50 mm thick insulation) 30 RM 1,555.00 46,650.00

f 16.3.10 65mm dia (50 mm thick insulation) 10 RM 1,343.00 13,430.00


Sr no.

DSR-

2016

Code


2.4

Providing and fixing in position the following Insulated

butterfly valves (Manual) with C I body SS disc, Nitrile rubber

seal & O ring PN-16 pressure rating for chilled/Hot water

circulation.Valves beyond 350mm dia shall be gear operated.

a 16.7.1.2 150 mm dia 2 No 6,625.00 13,250.00

b 16.11.3.7 100 mm dia (Motorized) 1 No 30,586.00 30,586.00

c 16.7.1.3 125mm dia No 5,780.00 0.00

d 16.7.1.4 100mm dia 28 No 5,330.0 149,240.00

e 16.7.1.5 80mm dia 2 No 3,719.0 7,438.00

f 16.7.1.6 65mm dia 4 No 3,351.0 13,404.00

g 16.7.1.7 50mm dia 12 No. 3,050.0 36,600.00

h 16.7.1.8 40mm dia 10 No. 2,686.00 26,860.00

2.5Providing and fixing in position the following Insulated

ball valves.

a 32mm dia 34 No. 1,901.00 64,634.00

b 25mm dia 28 No. 1,786.00 50,008.00

2.6Providing and fixing in position binder test points in the

chilled water pipelines.60 No 864.00 51,840.00

2.7Providing digital thermometers with probe suitable for binder

test point application.1 No 13,275.00 13,275.00

2.8Providing dial type pressure gauge with probe suitable for

binder test point application.1 No 13,275.00 13,275.00

2.9


balancing valves C I body flanged construction with EPDM

coated disc with long pitch with protected out pipe insulation

& PN-16 pressure rating for chilled/Hot water circulation as

per the specifications.

a 16.7.2.2 150mm dia No 23,798.00 0.00

b 16.7.2.3 125mm dia No 18,608.00 0.00

c 16.7.2.4 100mm dia 7 No 11,945.0 83,615.00

d 16.7.2.5 80mm dia 1 No 7,395.0 7,395.00

e 16.7.2.6 65mm dia 2 No 7,101.0

f 16.7.2.7 50mm dia 6 No. 6,386.0 38,316.00

g 16.7.2.8 40mm dia 5 No. 3,175.0 15,875.00

h 32mm dia 11 No. 2,820.0 31,020.00


Sr no.

DSR-

2016

Code


2.10


check valves (Non Return ) with dual plat eof C.I. body SS

plates vulcanized NBR seal flanged end & PN-16 pressure

rating for chilled/hot water circulation as per the

specifications.

a 16.7.3.4 100mm dia 6 No 3,893.00 23,358.00

2.11 PICV/PIBC/High Rangeability 2 way Control valve

Supply, installation, testing and commissioning of complete

set of PICV/PIBC/ High rangeability control valve/ pressure

independent dynamic balancing cum control valve, kit

comprising of Two Way Control Valve of Brass/C.I body of

PN16 ratings, motorised modulating actuators with linear

stroke of minimum 15 mm,The actuator shall have shut off

capability of min. 4 bar rating. LCD display digital

controller(BMS compatible),three nos NTC sensors with

complete wiring within AHU room,one thermowell,one power

supply unit of 230Vac/24Vac.Tranparent IP55 Control box for

mounting Digital controller and power supply unit.The valve

size shall be suitable for pipe size/coil capacity

a 50mm dia No 63,264.00 0.00

b 40mm dia 6 No 50,034.00 300,204.00

c 32mm dia 5 No 22,464.00 112,320.00

d 25mm dia 11 No 15,552.00 171,072.00

2.12

Providing and fixing in position of approved make flow

switch complete with copper control wiring at chiller outlet of

each machine.

7 No 2,880.00 20,160.00

2.13


suction guide or suction diffusers/Flowstraighteners or y-

Strainer.

a 125mm dia 6 No 16,704.00 100,224.00

b 100 mm dia 4 No 14,400.00 57,600.00

2.14 Y- STRAINERS


Y-Strainers of ductile CI body flanged ends with SS stariner for

chilled/hot water circulation as per the specifications.

a 16.7.4.4 100mm dia RO No 6,918.00

b 16.7.4.5 80mm dia RO No 5,026.00

c 16.7.4.6 65mm dia No 4,434.00 0.00

d 16.7.4.7 50mm dia 6 No. 3,516.00 21,096.00


Sr no.

DSR-

2016

Code


e 16.7.4.8 40mm dia 5 No. 2,478.00 12,390.00

f 32mm dia 11 No. 2,016.00 22,176.00

2.15 CONDENSATE DRAIN PIPE

Providing and fixing and in position the following PVC pipes

for condensate drain duly insulated with kinny foam & vapour

barrier duly secured with adhesive tape as per specification

,cut to required length and installed with all joints , including

the necessary fittings. (For all the AHU/FCU units upto the

main header in the shaft dor vertical risers)

a 65mm dia 20 RM 634.00 12,680.00

b 50mm dia 25 RM 484.00 12,100.00

c 40mm dia 30 RM 363.00 10,890.00

d 30mm dia 40 RM 288.00 11,520.00

e 25 mm dia 250 RM 207.00 51,750.00

2.16 AUTO AIR VENT

Supply, installation ,testing and commissioning of Auto Air

vents,at the specified locations in the chilled water piping ,

alongwith isolation ball valves, as per approved makes.

a Auto air vent with isolating ball valves (15 mm dia) 60 No. 1,440.00 86,400.00

2.17 FLEXIBLE PIPE CONNECTORS

Providing and fixing in position the following Flexible

connection on pipes with guide bolts.

a 100mm dia 18 No 7,488.00 134,784.00

Total Chilled water piping , valves and accessories

(Including Insulation)4,363,041.00

3 CONDENSER WATER PIPING AND VALVES

3.1 Condenser water piping

Providing and fixing in position the following MS C

Heavy class Condenser water piping , cut to required length ,

and installed with welded joints , including all necessary

fittings such as elbows , tees , etc.and confirming to the

specifications as detailed in the relevant chapter in the

document.Pipes will be accepted in order of preference (

Factory fabricated / Fabricated out of 7mm thick plates duly

rolled in a workshop and welded : for pipes beyond 350mm

dia)






dia. and above.

a 16.10.2 250mm dia RM 3,524.00 0.00


Sr no.

DSR-

2016

Code


b 16.10.3 200mm dia 60 RM 2,918.00 175,080.00

c 16.10.4 150mm dia 30 RM 1,983.00 59,490.00

d 16.10.6 100mm dia 10 RM 1,436.00 14,360.00

e 80mm dia 10 RM 1,022.00 10,220.00

f 50mm dia 10 RM 670.00 6,700.00

3.2 BUTTERFLY VALVES

Providing and fixing in position the following butterfly

valves with C I body SS disc, Nitrile rubber seal & O ring PN-

16 pressure rating.

a 16.11.1.2 150 mm dia 12 No. 5,914.00 70,968.00

b 16.11.1.4 100mm dia 3 No.4,685.0

14,055.00

c 16.11.1.5 80mm dia 3 No.3,302.0

9,906.00

d 16.11.1.7 50mm dia 3 No.2,671.0

8,013.00

e 32mm dia 3 No. 2,284.0 6,852.00

3.3 BALANCING VALVES

Providing and fixing in position the following balancing

valves as per the specifications.

a 150mm dia 6 No 75,744.00 454,464.00

3.4 CHECK VALVES

Providing and fixing in position the following check

valves (Non Return ) with dual plat eof C.I. body SS plates

vulcanized NBR seal flanged end & PN-16 pressure rating as

per the specifications.

a 16.11.2.2 150 mm dia 3 No 5,772.00 17,316.00

3.5 FLEXIBLE PIPE CONNECTORS

Providing and fixing in position the following Flexible

connection on pipes with guide bolts.

a 150mm dia 12 No 8,640.00 103,680.00

3.6 Suction Guide

Providing and fixing in position the following suction

Guide/Suction diffusers/Flowstraighteners .

a 150mm dia 3 No 22,464.00 67,392.00

TOTAL (Condenser water Piping , valves and accessories) 1,018,496.00

4 AIR SIDE WORKS

4.1 Site Fabricated Duct - GI duct

Supply,Fabrication , Installation and testing of sheet metal

ducts (rectangular/round ducting complete with neoprene

rubber gaskets, elbows, splitter,vanes, hangers, supportsetc.)

in accordance with the approved shop drawings and

specifications , and shall also confirm to the BIS

specifications.The duct shall be fabricated at site for to suit

pieces.

a 16.12.2.1 0.63mm (24 gauge) GSS 2900 SqM 630.00 1,827,000.00


Sr no.

DSR-

2016

Code


b 16.12.2.2 0.8 mm (22 gauge) GSS 300 SqM 751.00 225,300.00

c 16.12.2.3 1.0mm (20 gauge) GSS 80 SqM 983.00 78,640.00

d 16.12.2.4 1.25mm (18 gauge) GSS 50 SqM 1,104.00 55,200.00

4.2 Site Fabricated Duct - AL duct

Supply,Fabrication , Installation and testing of sheet metal

ducts in accordance with the approved shop floor drawings

and specifications , and shall also confirm to the BIS

specifications. The hardware shall be chrome plated or of

stainless steel.All lateral and transverse joints shall be sealed

with silicon based mastic sealant.

a Aluminum Sheet thickness - 1.00 mm 350 SqM 780.00 273,000.00

b Aluminum Sheet thickness - 1.25 mm 50 SqM 1,144.00 57,200.00

4.3

Supply, Fabrication, Installation and testing of Insulated Al.

Flexible ducts in accordance with the approved shop floor

drawings and specifications and shall also confirm to the BIS

specifications.

a 250 mm Dia. 110 RM 474.00 52,140.00

4.4 Grilles/Diffusers

Providing and fixing of Extruded aluminium supply and return

air grilles/diffusers/louvres with dampers, supply air plenum

etc. duly powder coated as per specifications and drawings.

a 16.15 Aluminium supply air grilles with damper. 16 Sqm. 7,132.00 114,112.00

b 16.16 Aluminium return air grilles without damper. 16 Sqm. 4,065.00 65,040.00

c 16.17 Aluminium supply air square diffuser with damper 6 Sqm. 8,686.00 52,116.00

d 16.18Aluminium return/exhaust air square diffuser without

damper.6

Sqm. 5,619.00 33,714.00

eAluminium return/exhaust air Valve circular/squirell diffuser

without damper.18 Sqm. 4,901.00 88,218.00

f Linear air grilles (150 MM wide) 50 RM 762.00 38,100.00

g Aluminium supply air collar damper 2.0 Sqm. 3,648.00 7,296.00

h AI Volume control dampers for ducts 15 Sqm. 4,901.00 73,515.00

4.5 Fresh Air/Exhaust Air Louvers

Supply, Installation, Testing and Commissioning of extruded

aluminium louvres with frame bird screeen , mounting

arrangement etc. as per specifications and drawings.

a Fresh Air/Exhaust Louvers 4.0 Sqm. 4,901.00 19,604.00


Sr no.

DSR-

2016

Code


4.6 MOTORIZED FIRE AND SMOKE DAMPERS

Supply, Installation, Testing and commissioning of motorized

combination fire and smoke damper (spring return type) of

approved make of atleast 120 minute fire rating and as per

the specifications as detailed earlier in the relevant

sections.The fire damper shall be complete with electronic

temperature sensor and electrically operated actuator .The

fire dampers shall be located in the supply/return air ducts, at

all fire rated crossovers (shafts/walls etc.) The control panel

will be such located that the reset can be easily done These

combination smoke and fire dampers shall be interlocked

with the building management system for fire detection /

HVAC and shall trip/close in the event of fire / smoke in the

respective zone .

a 16.20.1 Bare Fire Dampers with 400 mm sleeve 5 SqM 7,103.00 35,515.00

b 16.20.2 Control panel actuator , including Electrical,spring type

actuator,remote indication of the fire damper position.

20 No 6,604.00 132,080.00

cInterconnecting wiring for the fire alarm system with the AHU

and the smoke dampers.1 Lot 65,340.00 65,340.00

d

Sealing the openings around the sleeve of the fire dampers

with approved fire sealant, as per the recommendations of

the manufacturer and specifications.1 Lot 65,340.00 65,340.00


Sr no.

DSR-

2016

Code


4.7 FACTORY FABRICATED DOUBLE SKIN INLINE PLENUMS

a

Supply,installation,testing and commissioning of factroy

fabricated Inline Double skin HEPA filter plenum sections of

aluminum construction,on extruded aluminum sections

WITH THERMAL BREAK PROFILE (SAME AS THE

CONSTRUCTION FEATURES OF THE DOUBLE SKIN AHU) ,

suitable for housing 1 no.HEPA filters as described above for

,OT/ICU Scrub, exhaust as per specification with factory

fabricated access door and locking arrangement.

1 Nos. 5,990.00 5,990.00

4.8

Supply,installation,testing and commissioning of factory

fabricated and insulated (with self adhesive XLPE / Nitrile

rubber foam) square (595 mm x 595 mm) laminar air flow

plenum with diffusion plates , volume control device and

openable perforated sheet with 50% free area,suitable to be

mounted in the standard grid ceiling all duly fabricated in

aluminum and powder coated, as per specifications, If at site

no Moduler OT Than its used.

No. 12,524.00 0.00

4.9

Supply,installation,testing and commissioning of HEPA filters

of 610x610mm x 155 thick as per specifications and drawings

duly sealed with Epoxy and DOP tested.

HEPA filters as mentioned above for Up to 550 CFM handling

capacity for Terminals in Isolation 4 No. 9,257.00 37,028.00

4.10

Supply,installation,testing and commissioning of HEPA filters

of 610x610mm x 305/610 thick as per specifications and

drawings duly sealed with Epoxy and DOP tested.

HEPA filters as mentioned above for up to 2000 CFM

handling capacity for Exh Blower in AHU7 No. 7,079.00 49,553.00

4.11

Supply,installation,testing and commissioning of Fine filters of

610x610mm x 305 thick or bag type as per specifications and

drawings duly sealed with Epoxy and DOP tested.

Fine filters as mentioned above for up to 1000 CFM handling

capacity for supply Blower in AHU74 No. 4,901.00 362,674.00

4.12

Supply,Installation,Testing and commissioning of doble layer

canvas connection with 1/2 hr. fire rating as per

specification.150 SqM 2,178.00 326,700.00

TOTAL (AIR SIDE WORKS) 4,140,415.00


Sr no.

DSR-

2016

Code


5 MECHANICAL INSULATION

5.1 DUCT LINE ACOUSTIC TREATMENT

Supply, Installation, Testing and Commissioning of Acoustic

lining inside ducts using Non Fibrous fire retardant cross-

linked polyethylene foam of 30+/- 3 Kg/m3 density &

thickness of 15mm having porous surface on one side & a flat

surface on other side using Synthetic rubber based Adhesive

preferably Low VOC & high strength characteristic(Initial

portion of ducting and main plenum) as per specifications

a25mm thick ecosound (FR-Open Cell Cross Linked

Polyethylene) for AHU Room 150 SqM 1,653.00 247,950.00

b15mm thick ecosound (FR-Open Cell Cross Linked

Polyethylene) 450 Sqm 1,345.00 605,250.00

5.2 DUCT LINE THERMAL INSULATION

Supplying , installation, testing & commissioning of external

thermal insulation on ducts with Closed Cell Cross Linked

Polyethylene shall be 27 ± 3 Kg/m3. The product shall have

temperature range of –40 oC to 105oC. Thermal Conductive

not exceeding 0.033 W/mK at an average Temperature of

23°C. The insulation material shall be fire rated for Class 1 as

per BS 476 Part 6 : 1989 for fire propagation test and for Class

0 as per BS 476 Part 7, 1987 for surface spread of flame test.

Water vapour permeability shall be not less than 0.024 per

inch (2.48 x 10-14 Kg/m.s.Pa i.e. µ>7000: Water vapour

diffusion resistance).The Material shall have Fire Approval

from CBRI - Roorkie.

a

25 mm thick Closed Cell Cross Linked Polyethylene( XLPE)

Foam with 2 layer Coating of 7mile cloth star bond insulation

material .(For Open Duct)

350 SqM 850.00 297,500.00

b13 mm thick Closed Cell Cross Linked Polyethylene( XLPE)

Foam with Factory Aluminium sheet Laminated400 SqM 523.00 209,200.00

c9 mm thick Closed Cell Cross Linked Polyethylene( XLPE)

Foam with Factory Aluminium sheet Laminated2200 SqM 392.00 862,400.00

TOTAL (Mechanical Insulation works) 2,222,300.00


Sr no.

DSR-

2016

Code


6 ASSOCIATED ELECTRICAL WORKS

The rates for the distribution boards from the

Breakers and instruments shall also include the following :

A Wiring for light / Fan points with 1.5 sq. mm PVC insulated

copper conductor 1100 Volt grade stranded flexible FRLS

wires of approved make in 1.6 mm thick 25 mm dia MS

conduit including cost of providing & fixing saddles, hangers,

supports, cutting chases and filling chases for recessed

conduiting, and including the cost of providing and fixing a 6

amp 240 Volt Modular Plate type switches of approved

quality, colour, make and design with moulded cover plate

in zinc chromate passivated MS box and including the cost of

running 1.5 sq. mm PVC insulated copper earth wire for loop

earthing etc. complete

B TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with

adequate size of neutral link.

C All MCB’s shall be of minimum 10 KA breaking capacity.

D The breaking capacity of MCCB’s are mentioned panel wise.

All MCCB’s shall be with thermal magnetic microprocessor

releases as per BOQ

and following :

i. MCCB rating upto 250 Amps with thermal magnetic

releases.

ii. MCCB above 250 Amps with microprocessor releases.

E All MCB’s used for protection of resistive and lightly

inductive load shall be type “B” characteristic and

inductive (motor) load

shall be of type “C” characteristic.

F Degree of protection for following type of distribution panel

enclosure shall be as per IS:13947-1993.

i. IP 42 for indoor panels.

ii. IP 55 for ODU panel.

G All MCCB’s shall be provided with operating mechanism

for door interlock.

H All hinged door shall be earthed through 2.5 sq mm tinned

braided copper wire.

I Providing cable clamps / supports within distribution

boards cable alley.

J Current density of aluminium shall be 1sq mm for 1.0 Amps

for rated current of bus bars.

K Model, current capacity location and frame size of switchgear

shall be written inside of the panel doors with paint /

permanent marker as approved shop drawings / site

requirment.

L All meter shall be digital type.

M Current Transfomer shall be resin cast.

N All Panel Shall be BMS Compitable

6.1 Control Consol AHU/Fan Panel


Sr no.

DSR-

2016

Code


Supply, installation,testing and commissioning of floor

mounted desk type Remote Control with minic diagram

comproising of start/stop push buttons, status indicationi.e.

on/off/trip for 03 nos. Water-cooled screw chillers, 9 nos.

Condenser/Chilled/Hot water Pump sets,2 nos. cooling

Tower,22 nos. AHU , 4 Nos. Exh. Blower in AHU,4No. Liftwell

Pressurization Fan,1 No. Hot Water Generator,1 Nos. Fan

Section and 10 No. Spares with inernal control wiring

commissioning and accesorries.

1 Nos. 141,520.00 141,520.00

6.2 Plant/AHU/Fan Panel

Design, fabrication, assembling, wiring, supply, installation,

testing and commissioning of following LT panels fabricated

out of 14 guage CRCA sheet steel in cubical formationwith

reinforecment of suitable size angle iron and channel T iron

flats. All steel material used in the construction of panels shall

be powder coated. A solid busbar shall be provided at the

bottom of the panel with two connecting eyes for

termination. The boards shall be suitable for 415 volts, 50 Hz,

3 phase , 4 wire supply system. All the hardware used in the

fabrication of the panel shall be galvanized with zinc

passivation. The panel shall be compartmentalized to

accommodate one feeder in each compartment. A vertcal

cable alley of suitable width shall be provided to serve on or

two vertical feeder sections. Also the opening between the

busbar chamber and the feeder section shall be shrouded

with bakelite / hylam sheet with min.3 mm thickness.

The panel drawing shall be approved before taking up the

fabrication and compitable BMS if in future required.

In All panel Each starter should have remote control and

interlocking facilities including auto manual switch, NO/NC

contacts for control and must have auto manual operation

suitable to take signal from fire alarm panel for automatic

operation of fan in case of fire. All smoke /vent. fan panel

the starters shall have suitable facility to operate with fire

sensing control modules.

a HVAC Plant Room Panel-01 (Chiller/Pumps etc.)

Incoming

Incoming

1 no. 630 amp MDO ACB

0-500 volts voltmeter with SS with control fuses. (1set)

0-630 amp ammeter with SS and 800/5 CT's.(1set)

Phase indicating lights with control fuses.(1set)

Breaker ON/OFF/TRIP indicating lights.1set)

KW, Hz and power factor meter(2set)

Bus Bars

800 amp TPN Aluminum Bus Bar with heat shrinkable

insulation colored sleeves.

Outgoings

3 nos. 200 amp, MCCB, 25 KA with operating handles

for Chiller (Chiller with VFD)


Sr no.

DSR-

2016

Code


1 nos. 400 amp, MCCB, 35 KA with operating handles

for HWG

3 nos. 20 amp, TP MCCB, 10 KA with operating handles

with DOL starter,OLP with SPPR etc. ) (2Working + 1

Standby) for primary Chilled/Hot water Pumps


with VSD. ) (2Working + 1 Standby) for Secondary

Chilled/Hot water Pumps


with Star delta starter,OLP with SPPR etc. ) (2Working +

1 Standby) for condenser water Pumps


with DOL starter,OLP with SPPR etc. ) (2Working + 0

Standby) for cooling Towers

4 Nos, spare space

The base frame shall be 75 mm x 5 mm.

Panel as described above and in drawings. 1 Nos. 317,200.00 317,200.00

b HVAC AHU Panel MCC-02

Incoming

1 no. 63 amp MCCB

Phase indicating lights with control fuses.

Breaker ON/OFF/TRIP indicating lights.

Bus Bars



Outgoings

2 nos. 9-14 A,TP MPCB (with DOL starter ) incl. 1 no. MPCB

Spare

2 nos. 20-25 A,TP MPCB (with Star Delta starter ) incl. 1 no.

MPCB Spare


Panel as described above and in drawings. 1 No. 51,240.00 51,240.00

c HVAC AHU Panel MCC-03,08

Incoming

1 no. 32 amp MCCB



Bus Bars



Outgoings


Spare

2 nos. 4-6.3 A,TP MPCB (with DOL starter ) incl. 1 no. MPCB

Spare

1 nos. 6 A, MCB



d HVAC AHU Panel MCC-06,10,12,13,14,20,21

Incoming/Outgoing

1 nos. 2.5-4 A,TP MPCB (with DOL starter )



Sr no.

DSR-

2016

Code





e HVAC AHU Panel MCC-07,11

Incoming

1 no. 20 amp MCB



Bus Bars



Outgoings

2 nos. 2.5-4 A,TP MPCB (with DOL starter ) incl. 1 no. MPCB

Spare

1 nos. 6 A, MCB



f HVAC AHU Panel MCC-09

Incoming

1 no. 20 amp MCB



Bus Bars



Outgoings

2 nos. 4-6.3 A,TP MPCB (with DOL starter ) incl. 1 no. MPCB

Spare

1 nos. 6 A, MCB



g HVAC AHU Panel MCC-15,16

Incoming/Outgoing

1 nos. 4-6.3 A,TP MPCB (with DOL starter )





h HVAC AHU Panel MCC-17

Incoming/Outgoing

1 nos. 9-14 A,TP MPCB (with DOL starter )





i HVAC AHU Panel MCC-18

Incoming

1 no. 20 amp MCB




Sr no.

DSR-

2016

Code


Bus Bars



Outgoings

2 nos. 2.5-4 A,TP MPCB (with VSD Space Provision)

1 nos. 6 A, MCB



j HVAC AHU Panel MCC-19

Incoming

1 no. 160 amp MCCB



Bus Bars



Outgoings


Spare

4 nos. 6-10 A,TP MPCB (with VSD Space Provision)

1 nos. 2.5-4 A,TP MPCB (with VSD Space Provision)

2 nos. 9-14 A,TP MPCB (with VSD Space Provision)

3 nos. 20 A, MCB

5 nos. 6 A, MCB



k HVAC AHU Panel MCC-22 (Residential Block)

Incoming

1 no. 32 amp MCB



Bus Bars



Outgoings

1 nos. 4-6.3 A,TP MPCB (with DOL starter )

1 nos. 9-14 A,TP MPCB (with DOL starter )



6.3 CABLING (POWER )

Power Cabling and Earthing:

6.3.1

Supply, installation, testing & commisioning of Aluminum

conductor cables PVC sheathed, armoured cables of 1.1 KV

grade with termination glands and GI earthing, identification

tags, clamps and saddles etc.

a 3.5Cx185 Sqmm 100 Rmt 1,208.00 120,800.00

b 3.5Cx150 Sqmm 120 Rmt 988.00 118,560.00

c 3Cx16 Sqmm 20 Rmt 183.00 3,660.00

d 3Cx10 Sqmm 240 Rmt 173.00 41,520.00

e 3Cx 06 Sqmm 400 Rmt 138.00 55,200.00

f 3Cx04 Sqmm 800 Rmt 118.00 94,400.00


Sr no.

DSR-

2016

Code


g 2Cx04 Sqmm (Cu Conductor) 225 Rmt 155.00 34,875.00

h 4Cx 06 Sqmm 150 Rmt 206.00 30,900.00

6.4 Control Cabling

Supply, installation, testing & commisioning of Copper

conductor , PVC insulated, PVC sheathed armoured

cable of 1.1 KV grade (Which is Interconnecting wiring

for the fire alarm system with the AHU and the smoke

dampers and AHU to Control Consol Panel).

a 8C x 1.5 Sqmm 2400 RM 193.00 463,200.00

b 3C x .5 Sqmm 80 RM 70.00 5,600.00

c 2C x .5 Sqmm 60 RM 62.00 3,720.00

6.5

Supply, installation, testing & commisioning of cable

termination of above cables with Al./copper lugs &

flameproof brass compression glands on both the ends with

inhibting compound etc. complete as required.

a 9.2.26 3.5Cx185 Sqmm 6 Set 1,290.00 7,740.00

b 9.2.23 3.5Cx150 Sqmm 8 Set 1,120.00 8,960.00

c 9.2.5 3Cx16 Sqmm 2 Set 663.00 1,326.00

d 9.1.7 3Cx10 Sqmm 16 Set 171.00 2,736.00

e 9.1.7 3Cx 06 Sqmm 26 Set 171.00 4,446.00

f 9.1.7 3Cx04 Sqmm 56 Set 171.00 9,576.00

g 9.1.1 2Cx04 Sqmm (Cu Conductor) 22 Set 157.00 3,454.00

h 9.1.32 4Cx 06 Sqmm 6 Set 203.00 1,218.00

6.6

Supplying and installing following size of perforated G.I. cable

trays, G.I. bends with perforation not more than 17.5%, joined

with connectors, suspended from the ceiling with suitable

suspenders including G.I. bolts & nuts, painting of suspenders

etc. complete as required.

a 4.6.1 100 mm. Width x 50mm. Depth x 1.6mm. Thickness. 270 Rmt 436.00 117,720.00

b 4.6.2 150 mm. Width x 50mm. Depth x 1.6mm. Thickness. 90 Rmt 504.00 45,360.00

c 4.6.3 225 mm. Width x 50mm. Depth x 1.6mm. Thickness. 80 Rmt 604.00 48,320.00

d 4.6.4 300 mm. Width x 50mm. Depth x 1.6mm. Thickness. 50 Rmt 703.00 35,150.00

e 4.6.6 450 mm. Width x 50mm. Depth x 1.6mm. Thickness. 50 Rmt 1,024.00 51,200.00

6.7

Providing and fixing following size of G.I. strip / G.I. wire on

surface or in recess for loop earthing alongwith the existing

surface/ recessed conduit/ submain wiring / on cable tray/ on

surface including G.I. clamps etc. complete as required.

6.7.1 5.9 6 SWG G.I. wire 225 Rmt 85.00 19,125.00

TOTAL (HVAC Electrical Works) 2,374,062.00

30,243,129.00Total


SR. NO. DESCRIPTION UNIT QUANTITY RATE AMOUNT

1

Horizontal Rectangular High Pressure High Vacuum

Double Door Sterilizer.The sterilizer will be

manufactured as per IS: No.3829 (part 1) 1978 with ISI

Mark. The unit will be designed for operating pressure

30 to 32 psi.And corresponding to a temperature of

1340c.The sterilizer chamber would be formed out of

SS 316.The sterilizer will be provided with 2 Nos.

perssure locking type hinged doors.

nos 1.00 2797043.00 2797043.00

2 S.S 316 carriage suitable for rectangular sterilizer. nos 2.00 114134.00 228268.00

3 S.S 304 trolley suitable for Above carriage. nos 2.00 98912.00 197824.00

4

S.S control and packing table with drawer used for

seperation and packing of various sets of stermzed

sets of sterilzed goods for wads, clinics,operation

theatres etc.

nos 1.00 250,000 250000.00

5

S.s work table with two sink.The bench top is

fabricated out of 16 swg S.S 304 qlty.Ground and

polished with smooth surface and edge section.nos 1.00 114134.00 114134.00

6

Washer disinfector . Washer disinfector,single

door,suitable for cleaning and disinfection of surgical

instrument, suction bottles, cleaning buckets etc.nos 1.00 1133731.00 1133731.00

7

Ultrasonic cleaner of overall size 530mmlx330mm

wx350mmH internal ions:505x300x200mm,output

frequency 35 khz.Capacity 30 litres. nos 1.00 540233.00 540233.00

8 Drying cabinet with single door nos 1.00 677196.00 677196.00

9

S.S table trolley with 2 shelves . IF for use in the sterile

goodsstore when batching sterile goods for delivery

and also for short interval transport.nos 3.00 114134.00 342402.00

10 Steel -single distilled nos 1.00 213053.00 213053.00

11Stainless storage tank electric load 6 kw,capacity 120

lites.nos 1.00 220000.00 220000.00

12

Spray Gunriser -: Spray gun riser with attachments is

used for cleaning syringes,catheters, endoscopes and

variety of other instruments and articles used in sterile

services.

nos 1.00 146130.00 146130.00

GRAND TOTAL 6860014.00

Name of Work: Construction of 100 Bedded Hospital for ESIC at Bhilai

MEP WORKS :-CSSD EQUIPMENTS BOQ


NODESCRIPTIO

NSPECIFICATION MODEL UNIT TOTAL RATE AMOUNT

Main material : particle board with the density of 680kg/m cube .

Surface : CPL (continuous pressure laminate) in 0.5 mm thickness.

Process: postforming in duck - nosed profile . Edging : 2mm pvc edging,

Black color. Color : dark cherry.

maestro main

table - 1800Nos. 2 31950.00 63900.00

Main desk : table top : 25mm MFC (Melamine Faced Chipboard), plus

30 mm MDF (Medium Density Fiberboard) black pad. Modesty Panel:

18mm MFC. Leg : 25mm MFC plus 30mm MDF right and left pad.

joining top -

1050 x1200x750Nos. 2 13871.00 27742.00

Side return Desk: table top: 25mm MFC. Metal black spacers: diameter

+4cm, length =10.4cm Pedestal leg : 25mm MFC.

side unit -

1200x600x730Nos. 2 30548.00 61096.00

Pedestal : top panel : 25mm MFC, all other panels : 18mm MFC . Lock :

provided. Castor : provided handle : metal.

bookcase -

790x400x2200Nos. 2 28790.00 57580.00

Credenza : Top panel : 25 mm MFC , door panels: 18mm MFC, all other

panels : 18 mm MFC, Handle : metal.

back unit -

1400x470x760Nos. 2 57564.00 115128.00

Wardrobe: Top panel: 25mm MFC, bottom panel : 25 mm MFC . Wood

door panels: 18 mm MFC , glass Doors: 5mm, All other panels: 18 MFC,

Handle : metal. Joining top : top panel : 25mm MFC, leg : Metal.

mobile pedestal -

400 x 560 x560Nos. 2 17613.00 35226.00

Nos. 39 29838 1163682

Nos. 39 22113 862407

Nos. 39 67321 2625519

Nos. 39 13120 511680

3Conference

table

Manufacturing as per design and placing in position, Modular

conference Table of height 740mm, having two seater modules of size

1370x650mm , single seater module of 730x 650mm and round end

module of radius 710mm. The top of the table shall be made of

38mm (18mm plain particle board +18mm pain particle board

skirting +1mm Backing DL +0.6mm post formed natural Veneer ) of

approved quality . The legs of the table shall be 38mm thk (18mm

plain particle board +18mm pain particle board skirting + postforned

Dl of 0.6mm thk). The modesty panel of the tables shall be 600mm

high made of 18mm thk plain board confomi9ng to is 3087.Legs and

modesty panels shall be finished by using black Asian Paint Lipping

at edges for both tops and legs shall be made from MDF board of

approved quailty . The top , legs and modesty panel shall be joined to

each other by using eccentric wheel system . Glide screws shall be

put at bottom of legs for level adjustment of +/-7mm and a steel rib

tubular stiffner of 19mm square section of 1.2mm thk shall run

through each module to give sturdlness to the top.

Senate per seat

(16 seater)Nos 1 8990 8990

5Reception

Desk

5a

Reception

Desk

(2500x800x1

050)

Custom Made Nos. 3 95625 286875

5b

Reception

Desk

(1500x800x1

050)

Custom Made Nos. 3 159375 478125

6

Tipoy /

Centre

Tables types-

2 (550x 550

x 450)

UNDERSTRUCTURE ASSEMBLY : the understructure is an assembly of

tubular frames made of M.S.E.R.W. oval tubes of 3.5cm x 1.5cm. X

18BG. Thk.held together with perforated M.S. shelf + threaded nuts +

m/c screws. The ends of tubular frames are fitted with rubber studs at

the top and the bottom . The top studs are fitted with PVC vacuum

pads for mounting and gripping the glass top. the tubular frames are

black powder coated . CENTRE-PIECE TOP : The centrepiece top is

made from 0.95cm. thick Float glass with rounded corners of size 550W

x 550 D x 425 H. SHELF: it is a fabricated assembly made by 0.5cm. thk.

perforated M.S. sheet welded to M.S. sq. pipe 1.5cm. x 1.5cm. x 14 BG

thick with 0.3cm thick HR. steel plates on each side for fixing

understructure assembly . the shelf assembly is black powder coated.

CPR 2E Nos 8 4078 32624


FURNITURE COST ESTIMATE

1

Table for

Category 'A'

MS/DEAN

1

Table for

Category 'B'

HOD/

Proffessor

/Associate

Executive Desk of size -2200W x 1190D x 750H consisting of Top:36 mm

thk.side Panel:44 mm thk.Modesty Panel:18 mm thk. Mobile Pedestal

Configuration-1 pencil drawer, + 1 Box drawer + 1 filling drawer.

Dimensions: 406W x 550D x 640H, Pedestal Top Panel:25mm thk

Drawer Fronts & Carcass: 18mm thk. side Return Unit with Pedestal of

Dimensions:1380W x 480D x 700H Top:36 mm thk. Pedestal: 1 Pencil

drawer +3 Box drawers Top Panel-25 mm thk Drawer Fronts & Carcass

:18 mm thk. Back Unit / Cablnet Dimensions - 2406W x 400D x 1215H

side Panels:18 mm yhk PLB Shutters: 18 thk. PLB Cabiret Top Panel: 25

mm thk. PLB

Numero Uno

Main table-2200

Side Table-

1380X480X700

Back Unit-

2400X420X1200

Mobile Pedestal-

400X550X 460


NODESCRIPTIO


7 Table (study)

study Table of size 1200mm x 600mm x 740mm having having wood

laminate finish the table top / work surface : Made from 25mm thick

PLB with PVC lipping. Side panels: Made from 18mm thick PLT with PVC

lipping . Modesty panel: Made from 18mm thick PLT with PVC lipping .

Neat wiring flow with cut -outs on both sides, freestanding pedestal

for adequate personal storage

work Nos 40 4077 163080

8

high

backrest

executive

chairs with

arm rest for

category A

1)seat/back assembly:the seat is made up of insert moulded polyurethane

foam upholstered with foam laminated mesh fabric.the insert moulded

foam is assembled over a load bearing plastic seat cover.the back is made

up of two piece injection moulded frame.the inner frame is upholstered

with mesh fabric and mounted on the main assembly.the back has

adjustable lumber support support for achiving comfortable seating

posture.main assembly.sub assembly seating size=52.5cm width,51cm

depth. sub assembly back size=48.5cm max width,62 cm ht. effective back

ht.from seat=57cm. 2)POLYURETHANE FOAM:the polyurethene foam for

seat is moulded with density=75 ±4kg/m3 and hardness=34±4.

3)ARMRESETS(ADJUSTABLE): THE ARMREST TOP IS INJUSTION MOULDED

IN POLYURETHENE and mounted on the uinjuction moulded ht.adjustable

type armrest.the armrest is adjustable upto 4.5cm in three steps and with

adjustable armtop out of dim=62 to 65 cm arm top centre to centre

dim=53 to 56 cm. 4) front pivot sinchro mechanism.the mechanism is

design with following features-3600 revolving type-single point control-

fron pivot for till with feet resting on ground ensuring more comfert-tilt

tention adjestment-3 positions locking with anti shock

leoma 9m02 nos 2 17617 35234

10

high

backrest

executive

chairs with

arm rest for

category B

SETBACK ASSEMBLY-the seat/back are made up of 1.2 cm thk.hot

pressed plywood up holsted with fabricant moulded polyurethene

foam together with moulded seat and backcovers.the back foam is

design with conured lumber support for extra comfort.(high backsize

50cm widthx 72cm ht.seat size 50cm wx46cm (D) polyurethene foam-

the polyurethene foam is moulded with density=45+/- 2kg m3 and

ha4rdness=2+/-2 on hampden machine at 25% compression. seat /back

covers the seat covers with injuction moulded with in black co-polymer

polypropilene and back cover is vaccume formed from ABS sheets

armrests.the one peace armrests made of black integral skin

polyurethene with 50 to 70 shore (A) hardness and reinforced with MS

insert. the armrest are scretch and weather resistant.the armrest are

fitted to the seat the armrest connecting strip assembly made of 0.5 cm

thk.HR steelb CENTER PIVOT MECHANISM the centre pivot mechanism

is design with following features-3600 revolving types 17 degree max.

tilt on pivot at centre.tilt tention upright locking telescopic below

assembly-the below is three piece telescopic type and fitted with 5 no's

twin wheel casters(casters wheel dia.5cm) the padistal covered with a

regency 7001D Nos. 51 16336 833136


NODESCRIPTIO


11

Medium

back visitors

chairs for

category B

H.O.D. /

P.A./

prof.Room

SEAT / BACK ASSEMBLY: The seat / back are made up of 1.2 cm thick

hot pressed plywood, upholstered with fabric and moulded

polyurethane foam together with moulded seat and back covers, the

back foam is designed with contoured lumbar support for extra

comfort . (MEDIUM BACK) SIZE :50.0cm. (W) x 49.0cm. (H) SEAT.SIZE:

50.0cm. (W) x 46.0cm. (D) . POLYURETHANE FOAM: The polyurethane

foam is mouulded with density = 45 +/-2 kg/ m3 and Hardness =

20+/-2 on Hampden machine at 25% compression .SEAT / BACK

COVERS: the seat and back covers are injection moulded in black co-

polymer polypropylene ARMRESTS: The one - piece armrests made of

back integral skin polyurethane with 50-70 shore ;A' Hardness and

reinforced with M.S. insert, the armrest are scratch and weather

resistant . The armrests are fitted to the seat with seat/ armrest

connecting strip assembly made of 0.5cm . thk . HR steel. TUBULAR

FRAME : The tubular frame is centilever type & made of Dia 2.54cm.

(1") x 14 BG M.S. E.R.W.tube and black powder coated

Rergency 7003D Nos. 4 8954 35816

12

Medium

back rest

chairs with

arm rest for

category 'C'

SEAT / BACK ASSEMBLY: The seat / back are made up of .2 cm thick


polyurethane foam together with moulded seat and back covers, the

back foam is designed with contoured lumbar support for extra

comfort . (MEDIUM BACK) SIZE :50.0cm. (W) x 49.0cm. (H) SEAT.SIZE:

50.0cm. (W) x 46.0cm. (D) . POLYURETHANE FOAM: The polyurethane

foam is mouulded with density = 45 +/-2 kg/ m3 and Hardness =

20+/-2 on Hampden machine at 25% compression .SEAT / BACK

COVERS: the seat covers are injection moulded in black co- polymer

polypropylene and back coveris vacuum formed from ABC sheets

ARMRESTS: The one - piece armrests made of back integral skin

polyurethane with 50-70 shore ;A' Hardness and reinforced with M.S.

insert, the armrest are scratch and weather resistant . The armrests are

fitted to the seat with seat/ armrest connecting strip assembly made of

0.5cm . thk . HR steel. CENTRE PIVOT MECHANISM The center pivot

mechanism is designed with the following features : 3600 revolving

type . 17 maxmimum till on pivot at center . Tilt tension adjustment.

upright locking .TELESCOPIC BELLOW ASSEMBLY : The bellow is 3 piece

Rergency 7002D Nos 120 15323 1838760

14

Low back

Visitcrs

chairs for

category D

Asst.prof /

Tutor / Tech

/ Pre. Tech /

Lab asst.

/adm off.

Staff /prep

00m /Record

/ seecurity

SEAT / BACK ASSEMBLY: The seat / back are made up of .2 cm thick


polyurethane foam with PVC lipping all around . , the back foam is

designed with contoured lumbar support for extra comfort .BLACK

SIZE : 49.0CM . (w) X47.0cm (H) SEAT SIZE:49.0cm. (w) X44.0cm. (D) .

POLYURETHANE FOAM: The polyurethane foam is mouulded with

density = 45 +/-2 kg/ m3 and Hardness = 20+/-2 on Hampden

machine at 25% compression. TUBULAR FRAME: The tubular frame is

cantilever type & made of Dia. 2.54cm. (1")x 14 BG M.S.E.R.W. tube

and black powder coated.

Premier-7112R Nos 30 4553 136590


NODESCRIPTIO


15

Doctor /Staff

/Nurse

/Orderly

Change

Room.

Ladies /

Gents

lockers

(380x457x18

30)

4Dr locker units of height 1830 mm with looking mechanism: 10 Lever

cam lock with lock lever and option of hasp arrangement Material:

CRCA 0.6cm Thickness . Construction : Rigid knockdown construction.

Shelf Uniformly Distributed Load Capacity per each shelf level is 35

kg maximum. Finish: Epoxy polyester powder coated to the thickness

of 50 microns (+/-10) .Handle / Label holder .Aesthetically appealing

snap fit ABS plastic handle . plastic label holder for identification.

Ventilation: Attractive punched pattern for ventilation

4 Door lockers

per Units with

Locks

Nos 10 12953 129530

16

2 Seater Sofa

(Uphoistere

d /high

Cousioned )

2 SEATER LOUNGE SOFA of size :W 1130 mmx D 700 mm x H 785 mm,

Seat ht. 435. SIDE FRAME ASSEMBLY : The side frame assembly is fitted

to the two ends of the connecting beam assembly to form the leg-cum-

armrest assembly . It is made of a MS. E.R.W. tube dia 3.81 cm. x 14 BG.

thk. and black power coated .The ends are fitted with ABS moulded end

caps. TIE MEMBER : it is the connecting beam assy. which holds the two

side frame to each other. 2 nos. tie members are used to connect the

side frames. The tie member is made of MS. E.R.W. tube dia 3.81 x14

BG. thk. and black power coated.The seat /back assemblies are

mounted on one of the tie- member which has 5cm. x5.5cm longx .5

cm.thk. MS. std. angles welded to mount the seat and back.SEATREST

ASSEMBLY : the seat rest assembly consists of a fabricated inner-frame

assembly insitu moulded with Polyurethane foam having density= 45+/-

2 kg./ch3. the hardness of the P.U. foam 23 -27 kgs. on hampden m/c.

for 25% compression of the foam. the complete moulded seat rest

assembly is covered with a replaceable fabric upholstery cover.SEAT

SIZE: 52 (W)X 50CM. (D)X6CM (T) BACKREST ASSEMBLY : THE BACK

REST ASSEMBLY IS FLEXING TYPE AND CONSISTS OF A fabricated inner

frame assembly insitu -moulded with polyurethane foam having

density =45+/- 2 kg/cm3. The hardness of the P.U. foam =16-20 kgs. on

Hampden m/c for 25% compression of the foam .The complete

moulded backrest assembly is covered with a replaceable fabric

upholstery cover.BACK SIZE : 52 (W) 59(H) 6 (T) ADJ.glide is injection

moulded in black nylon & fitted to the front end of side frame assembly

L42 NOS. 10 14015 140150

18

STORAGE

UNIT (SIZE

IN MM =

1200 X 450 X

750 )WITH

PF TOP

CUSTOM MADE Nos 45 12559.00 565155.00

20

Metal

Perforated

Chair on

Bench-

3Seater

Metal Perforated 3 seater Bench having of size: W 1680 mm X D

570MM X H 850 mm Seat hight 460 mm, SEAT BACK FRAME ASSEMBLY:

The seat and back are made of 18BG thick CR steel perforated sheets

which are welded to a seat/back frame assembly made of Dia. 1.9 cm

(3/4") X 16BG thick MS ERW tube connection beam. SEAT SIZE 39.0cm

(W) X 41.5cm. (D) (Approx,) BACK SIZE: 39.0cm. (W) X 21.5cm. (H)

(Approx.). ARMREST : it is made up of oblong tube of size 35 mm X

15mm X 1.6 Thk. & Dia. 15mm bright bar wekded to seat & back frame

assembly. CONNECTING BEAM ASSEMBLE: it is a U- shaped fabricated

assembly made of Dia. 3.81cm. (1 1/2") X 14 BG. MS ERW twin tubes.

The connecting tubes are welded together with MS base plates made of

12BG thick CR. Steel and mounting plate made of 0.5cm thick HR Steel

Threaded inserts are provided on both ends of each connection tube or

fixing leg assembly on each side. The connecion beam assembly is

power coated. LEG ASSEMBLY: it is a 2-piece fabricated to form a box

section made of 16BG thk. CR steel. Threaded nuts are welded to the

box section for fixing adjustable glide screws. The leg assembly is

powder coated. ADJUSTABLE GLIDE: The adjustable glide is injection

molded is black Nyion 6 and is used for level adjustment of the beam

seation on uneven floor surface. it is fitted to the leg assembly.

BPMXX3 Nos. 135 8542.00 1153170.00


NODESCRIPTIO


21

Metal

Perforated

Chair on

Bench- 2

Seater

Metal Perforated 2 seater Bench having of size: W 1110 mm X D

570mmX H 850 mm Seat hight 460 mm, SEAT BACK FRAME ASSEMBLY:

The seat and back are made of 18BG thick CR steel perforated sheets

which are welded to a seat/back frame assembly made of Dia. 1.9 cm

(3/4") X 16BG thick MS ERW tube connection beam. SEAT SIZE 39.0cm

(W) X 41.5cm. (D) (Approx,) BACK SIZE: 39.0cm. (W) X 21.5cm. (H)

(Approx.). ARMREST : it is made up of oblong tube of size 35 mm X

15mm X 1.6 Thk. & Dia. 15mm bright bar wekded to seat & back frame

assembly. CONNECTING BEAM ASSEMBLE: it is a U- shaped fabricated

assembly made of Dia. 3.81cm. (1 1/2") X 14 BG. MS ERW twin tubes.

The connecting tubes are welded together with MS base plates made of

12BG thick CR. Steel and mounting plate made of 0.5cm thick HR Steel

Threaded inserts are provided on both ends of each connection tube or

fixing leg assembly on each side. The connecion beam assembly is

power coated. LEG ASSEMBLY: it is a 2-piece fabricated to form a box

section made of 16BG thk. CR steel. Threaded nuts are welded to the

box section for fixing adjustable glide screws. The leg assembly is

powder coated. ADJUSTABLE GLIDE: The adjustable glide is injection

molded is black Nyion 6 and is used for level adjustment of the beam

seation on uneven floor surface. it is fitted to the leg assembly.

BPMXX2 Nos. 20 6718.00 134360.00

22Chairs for

canteen

chair having width 52.0 mm, depth 54.5mm, height 80.5mm and seat

height 43.0 mm. seat & back shell is injected moulded in propylene.

Tubular frame is in 19mm dia. Stainles steel tube.

MPC4 Nos. 50 2950.00 147500.00

23

Table for

canteen (4

seater) (size

in mm =

900x900)

understructure: the understructure is foldable and stackable, made

with combination of aluminium and plastic. Centre column is of

serracted aluminium extrusion of diameter 70mm, which is anodized.

Base is made in 2 pieces of die cast aluminium with buffed finish. it is

bolted together with the centre column and top flange. MDF top with

PU coating (both profiles): size 800mmx800x25mm thick made of

25mm thick MDF , painted in yellow, red, orange, wine, beige PU

coating on a sealer coat. PU coating done on both . PU coating on sealer

coat. PU coating done on both top and bottom surfaces. PU coating has

hardness of 3H. Top is fitted to the understructure with no. bx16 pholip

head screw rubber wood top with PU coating (both profiles) size :

800mm x18mm thick made of 18mm thick rubber wood. top is made of

2 finishes: wenge and natural. stainless steel top size : 800mm x

800mm x 1.2 mm thick 24mm thick - top assembly top made from 1.2

mm thick SS- 304brushed steel finish sheet welded stiffner assembly

made from 0.6 mm thick SS-304 sheet glued with top with special glue.

café pod -

rubber wood

top

Nos. 13 13505.00 175565.00

11,818,620.00 TOTAL COST FOR FURNITURE WORKS


Rate Amount

MR

Supply, Installation, Testing and

commissioning etc as required for the

follwing items required for the Operation

Theatre

1 MR

Stainless Steel 304 Grade with1.5mm

Pre Fabricated Modular Operation

Theatre.Wall Panel backed with 12mm

thick. gypsum with proper supports.3.00 Set 997800.00 2993400.00

2 MR

Stainless Steel 304 Grade with 1.5mm

Pre Fabricated Modular Operation

Theatre.Ceiling Panel backed with 12mm

thk. gypsum with proper supports.3.00 Set 424804.00 1274412.00

3 MR

Filling of Joints ,Cavity and imported

Antuibacterial paint.Filling of all joints &

cavities with epoxy filler, sanded flush for

seamless finish with one primer and three

coats of antibacterial & antifungal paint .

That is equivalent to a dry film thickness of

300 microns .

3.00 Lot 392130.00 1176390.00

4 MR

Hermatically Sealed automatic sliding

door. (Patient entry).Automatically

Operated hermatically sealed Sliding

Doors 1500mm x 2100mm (WXH) with glass

vision window of 300mm x 300mm (WXH)

along with all accessories.

3.00 Set 920450.00 2761350.00

5 MR

Hermatically Sealed automatic sliding

door. (Doctors entry).Automatically

Operated hermatically sealed Sliding

Doors 1000mm x 2100mm (WxH) with glass

vision window of 300mm x 300mm

(WxH) along with all accessories.

3.00 Set 842000.00 2526000.00


MEP WORKS :-INDIAN OPERATION THEATRE - BOQ

Description Quantity UnitSr.

No.Code


Rate Amount

MRDescription Quantity Unit

Sr.

No.Code

6 MR

Laminar airflow.Laminar Planair Ceiling

system with unidirectional airflow with "S"

class Hepa filter with an efficiency 99.97%

down to 0.3 micron. The holding structure

& top plenum are made up of Aluminium

Sheet with a thickness of 1.6mm. It should

be sealed with gasket conforming to DIN

4799 standards for the air distribution

system. 2 layer diffuser with monofilament

precision woven polyester of uniform

porosity with an open area of sufficient

resistance to create laminar from diffusers

face and inetgral lighting provides an

illumination level in excess of 15000 Lux in

operating area and 10000 Lux other with

flickerless digitally controlled stepless

dimming down to 5%.

3.00 No. 398000.00 1194000.00

7 MR

Medical Gas pipeline inside Operation

Theatre .Medical Gas pipeline system

inside OT for Medical gases including all

fittings and fixtures.

3.00 Set 398000.00 1194000.00

8 MR

Electrical wiring.Electrical wiring within the

OT Area, conduit pipes and electrical switch

& Socket with Electrical Distribution board

for Operating room with MCB's and Relay

cards.

3.00 Lot 60000.00 180000.00

9 MR

Peripheral lights.Recess mounted IP 54

protocol, non-hygroscopic Peripheral

Lights for clean room application. Each light

set having 2nos of 36 watt flouracent

lamps with digitaly controlled dimmable

ballast.

18.00 Set 19200.00 345600.00

10 MR Scrub 3 - bay. 3.00 No. 159680.00 479040.0011 MR Writing board.Magnetic writing Board. 3.00 No. 13200.00 39600.00

12 MRX-ray view box.Two Plate X-Ray viewing

screen with flicker free dimming range from

3 to 100% with complete accesories.

3.00 No. 39150.00 117450.00

13 MR

Membrane type Operating room Control

panel.Membrane type Operation

Theatre Control Panel (6 service Tiles)

mounted. Flushed in the theatre wall with

complete distribution board with all

accessories. Following are the

controls/display available:-

* 1 no Day Time Digital Clock.

* 1 no Elapsed Time Digital Clock.

* 1 no Hands Free Telephone.

* Peripheral Light Control

* Medical Gas Alarm for 4 gases.

*Temperature & Humidity Indicator .

* Alaram for Vacum.

3.00 Set 393610.00 1180830.00


Rate Amount

MRDescription Quantity Unit

Sr.

No.Code

14 MR

Dirty Hatch box.2 door dirty hatch box made

up of Stainless steel grade 304. One door will

be opened at one time , indicator on both

sides.The hatch will be designed in such a

way that only one door will be opened at

one time. The UV light will glow when both

the doors are in closed position.

3.00 No. 298800.00 896400.00

15 MR Ceiling mounted Operating room light. 3.00 Set 1202300.00 3606900.00

16 MR

Pendants.Pendent with weight carrying

capacity of 100Kg. The pendant should have

electrical sockets, one monitor shelf and gas

outlets for medical gas supply.

6.00 Set 395000.00 2370000.00

17 MR

Pressure relief damper.Pressure Relief

Damper. Made up of 304 graded stainless

steel blades with all accessories.3.00 Set 49648.00 148944.00

18 MR

Anti - static flooring.2mm thick Anti static,

conductive dissipative flooring tile laid on

a semi conductive adhesive base resistant to

mechanical stress and dynamic load and

washable.

3.00 Lot 320130.00 960390.00

23444706.00TOTAL


S.NO. FURNITURE ITEM QUANTITY PRICE AMOUNT

1

TRACK SYSTEM

COMPLETE WITH

CURTAINS

ICU, CCU, RECOVERY,

TRIAGE, , AND WARDS

BEDS

200 24000 4800000

2

IV TREE SYSTEM, 5

POINT HANGER WITH

6' TRACK AND ALL

ACCESSORIES WITH 2

IV TRACKS PER BED

FOR BEDS 200 31200 6240000

TOTAL 11,040,000.00


MEP WORKS :-TRACK SYSTEM - BOQ


Quantity Rate Amount

MR

1 MR

MILK BOILER /TEA BOILER

Cap.50Ltrs. S.S.Sheet insulated body with

triple jacket. The water jacket will be

fitted with 2 Kw heating element. Milk

outlet, water level indicator & draw

off valve at the bottom & water

tank. Phillips element, Elcon

thermostat, GVC rotary switch, LED

indicator for Power, 4mm thickness 3

core wire Rajdoot/ Plaza make

1 No. 78500.00 78500.00

2 MRMICROWAVE OVEN

Cap.20-30Ltrs.

IFB-MAKE - SC-2

1 No. 29800.00 29800.00

3 MR

PICK UP COUNTER WITH OVERSHELF

Size 1800X600X850 + 300

Top

3 sides, under & over shelf of s.s.sheet,

on m.s.angle & s.s.tubular legs frame

work. The counter will have 3 sides fully

covered, operator side open. With one

under shelf. One over shelf 300mm wide

& running along the full length of counter

u type heating element of 1 Kw is placed

under the one head

shelf to keep the dishes warm provided

with toggle switch also connected with

4 mm 3 core wire.

2 No. 90000.00 180000.00

4 MR

WORK TABLE FOR SUPPORT OF TWO

BURNER RANGE

Size 1350x600x850mm

Top & undershelf of s.s.sheet on

m.s.anlge frame work & s.s.tubular legs,

with adjustable feet. Top to have sound

deadning material lining as required.

1 No. 39000.00 39000.00

5 MR

TWO BURNER COOKING RANGE

App. Size 1200X600X850mm

Frame work of m.s.anlge duly painted,

mounted on s.steel tubular legs with

adjustable feet. Top & sides & under

shelf of s.s.sheet. The range will be

complete with 2nos. Hy-pressure gas

burners with individual control valves.

Cast iron pan support

1 No. 35000.00 35000.00


MEP WORKS ABSTRACT SHEET :-KITCHEN EQUIPMENT - BOQ

Sr.No

.Code Description Unit As Per

Boq / MR



MR

Sr.No


Boq / MR

6 MR

EXHAUST HOOD (Without Ducting,

Fixing & Extraction fan) FOR TWO

BURNER RANGE

Size 1950x750x600mm

Made of s.steel sheet, 20G thick duly

welded & pop rivetted as required. The

hood will be complete with s.s.sheet

removable type baffle filters. Complete

with greese collection channel & greese

collection cup/s.

1 No. 75000.00 75000.00

7 MR

JUICER (table top model)

Cast Aluminum/CI body, duly

polished / painted, with worm &

perforated insert. Top feeding tray.

Worm easily cleanable fitted with 1/2HP

elect. motor.

1 No. 58000.00 58000.00

8 MR

CONVEYOR TOASTER

App. Cap. 100-125 Toasts/hr.

S.S.Sheet body, having s.s.sheet conveyor

belt. App.225mm wide. The unit will have

heating elements on top & lower

portion of conveyor belt with variable

heat & speed control switch. (MADE IN

ITALY)

1 No. 98000.00 98000.00

9 MR

WORK TABLE WITH SINK

Size 1950x600x850+150

Top & Sink bowl of s.s.sheet, on s.s.anlge

& s.s.tubular frame work with cross

bracing at lower portion. Sink bowl will

be integrally welded with top & grinded

smooth. Sink bowl size 450x450x250mm.

1 No. 73500.00 73500.00

10 MR

FOUR DOOR REFRIGERATOR

App. Size 1200x675x2000mm

Double walled, insulated 'PUF' body

made of 0.8mm thick s.s.sheet. Inside

chamber to have 4nos. S.s.wire shelves

on adjustable channel. The unit will

have 4 doors with magnatic rubber

gascuts & locking provision. The

condensing unit, consisting of 'Kirlos

2 No. 155000.00 310000.00



MR

Sr.No


Boq / MR

11 MR

WORK TABLE

Size 1500X600X850mm





1 No. 48000.00 48000.00

12 MR

THREE BURNER COOKING RANGE

SIZE 1800X600X850

Structure made of m.s. angle

of size 38x38x5mm, duly rust proof

painted. Top of 16Swg thick s.s.sheet.

All four side covered up to height of app.

10” by 20Swg stainless steel sheet.

Bottom stainless steel stripes sheets

complete with gas burners, valves p

1 No. 74000.00 74000.00

13 MR


Fixing & Extraction fan) for

THREE burner RANGE

Size 1950x750x600mm






collection cup/s.

1 No. 75000.00 75000.00

14 MR

LOW HT. TABLE for supporting low

height burner

Size 750x750x600mm

Specification same as that of work

table but the table will be without

undershelf & will have cross bracing

support at lower portion.

2 Nos. 25000.00 50000.00

15 MR

LOW HT. BURNER

Size 750x750x600mm

Specification same as that of cooking

range but the unit will be without

undershelf, but will only have cross

bracing support at lower portion.

2 Nos. 27000.00 54000.00



MR

Sr.No


Boq / MR

16 MR



LOW HEIGHT BURNER range

Size 1650x750x600mm






collection cup/s.

2 Nos. 66000.00 132000.00

17 MR

THREE BURNER COOKING RANGE

O/S 1800X600X850

Structure made of m.s. angle

of size 38x38x5mm, duly rust proof

painted. Top of 16Swg thick s.s.sheet.

All four side covered up to height of app.

10” by 20Swg stainless steel sheet.

Bottom stainless steel stripes sheets

complete with gas burners, valves p

1 No. 74000.00 74000.00

18 MR

WORK TABLE for support of 03 burner

cooking range

Size 1500X600X850mm





1 No. 48000.00 48000.00

19 MR



THREE BURNER RANGE

Size 1950x750x600mm






collection cup/s.

1 No. 75000.00 75000.00

20 MR

BULK COOKER/boiler TILTING TYPE

Cap.160Ltrs.

Specification same as Sno.13 but the

frying pan will be Of rectangular shaped

with 12”depth & a pouring lip & the unit

will be fitted with v type high pressure

gas burner with control valve & pilot

lamp.

1 No. 186000.00 186000.00



MR

Sr.No


Boq / MR

21 MR

BULK FRYER TILTING TYPE

Cap.100Ltrs.

Triple jacketed body of stainless steel

sheet, Inner most jacketed of 16g thick

with 12g thick dish ended bottom,

second wall for air gap of 18g stainless

steel sheet & outer insulation jacket also

of 18g stainless steel sheet. The unit will

have counter

1 No. 185000.00 185000.00

22 MR



BULK COOKER & FRYER

Size 1650x750x600mm






collection cup/s.

2 Nos. 66000.00 132000.00

23 MR

WET GRINDER

Cap.15ltrs (1.0HP)

Stainless steel sheet constd. Body with

s.s.sheet constd. Revolving drum,

cromium plated pillar support on

m.s.angle frame work fitted with

electric motor gear box & grinding stones

& coconut scraper.

1 No. 65000.00 65000.00

24 MR

DOUGH KNEADING MACHINE

(CROMPTON MOTOR 2.0 HP)

App. Cap of Bowl 25Ltrs.

S.S.Mixing bowl, with s.s.rod/strip mixing

arm, mounted on steel tubular & sheet

frame work duly painted. Complete

with 1.0HP Elect. Motor with control

switch.

1 No. 90000.00 90000.00

25 MR

POTATO PEELER

Cap.15Kg./chrgs. (CROMPTON MOTOR

1.0 HP)

16 gauge Stainless steel sheet peeling

drum, lined inside with Abrasive

material, stainless steel /cast iron

rotating peeling disc. Top of the drum will

have a potato inlet door, waste Inlet

provision peeled potato discharge door &

waste water Outlet pipe

1 No. 78000.00 78000.00



MR

Sr.No


Boq / MR

26 MR

PULVeRISER (Std.) (CROMPTON MOTOR

1.0 HP)

Stainless steel sheet body,20g thick. the

unit will have A top feeding tray & a

housing of stainless steel casting With

grinding plates & 3 type of meshes for

variable type Of grinding requirements.

The unit will be fitted with 1.0 hp single

Phase electric

1 No. 69200.00 69200.00

27 MR

WORK TABLE support of pulverisor

Size 1500X600X850mm





1 No. 48000.00 48000.00

28 MR

WORK TABLE WITH SINK for vegetable

washing

Size 1950x600x850+150

Top & Sink bowl of s.s.sheet, on s.s.anlge

& s.s.tubular frame work with cross

bracing at lower portion. Sink bowl will

be integrally welded with top & grinded

smooth. Sink bowl size 450x450x250mm.

1 No. 73500.00 73500.00

29 MR

CHOPPING BOARD for manual

vegetable cutting

size:- 1200X600X850mm

Frame work made of s.s.anlge top

will have P.P./Nylon Board for

chopping 700x700x100mm chopping

board.

1 No. 78000.00 78000.00



MR

Sr.No


Boq / MR

30 MR

VEGETABLE CUTTING MACHINE

Aluminium casted body with ½ hp

electric motor safety switch & double

feed pusher for round flat & vertical

shaped food items etc., the unit will be

Table top model with easy to clean

provision. Provided with 4 no cutting

discs for slicing grating Dicing

1 No. 98500.00 98500.00

31 MR

CHAPPATI COLLECTION TABLE

Size 1500X600X800

Top tray of 16G s.s.sheet, tray will have

App.100mm ht. collor all around,

mounted on s.s.tubular legs with

adjustable feet & one s.s.sheet

undershelf.

1 No. 48000.00 48000.00

32 MR

CHAPPATI ROLLING TABLE

Size 2100x650x850mm





THREE SIDE CROSS BRACING MADE

OF S.S. PIPE 1" DIA FOR UNDERNEATH

STORAGE.

1 No. 79500.00 79500.00

33 MR

CHAPPATI PLATE CUM PUFFER

Size 1800x650x850mm

Frame work of m.s.anlge, mounted on

s.s.tubular legs frame work. All sides

pannels & undershelf of s.s.sheet, top

plate 10mm thick mild steel with cast

iron puffing grills for puffing of

chappaties. Complete with 'V' shape

LPG burners with individual cont

1 No. 98000.00 98000.00

34 MR


Fixing

& Extraction fan) for chapatti plate

Size 1950x750x600mm






collection cup/s.

1 No. 75000.00 75000.00



MR

Sr.No


Boq / MR

35 MR

FOOD TROLLEY WITH 4 ROUND PANS, 1

RICE TRAY & STORAGE beneath

O/S 1350X750X900mm

S.S.Sheet insulated body, Frame

work of m.s. anlge of size

38x38x5mm, mounted on 4 castors (2

with brakes) of size 150mm top to have

cutout for 4nos. Round pans for Dal,

Subzi etc. with 1 rice tray & storage

below. Three side covered with s.s.sheet

with s.

4 Nos. 75000.00 300000.00

36 MR

TRAY CARRIER TROLLEY

Size 1200X600X1200mm

S.S.Bottom base shelf mount at 150mm

with all four sides turned down

50mm in 12mm and secured to welded

s.s.anlge frame work & PROVIDED WITH

THREE NOS. OF DETACHABLE TRAYS

CUM SHELFS UNIT WILL BE MOUNTED

ON 4" PILLAR TYPE CASTORS WHEELS

(2

NOS. WITH BRAKE & 2 NOS. WITHOUT

BRAKE)

1 No. 65000.00 65000.00

37 MR

TRAY SET UP COUNTER WITH BAIN

MARIE & DOUBLE OVERSHELVES

Size 1800x600x850+375+225

Top of 16G s.s.sheet, Bain Marie water

tank of

18G s.s.sheet, fitted with 3.0kw heating

element with automatic temperature

controller. Water outlet provision with

drain valve, 3 sides covered with

20G s.s.sheet, Top to accommodate

s.s.sheet Food Pans with GN pan

1x2x4" depth with lid 5 sets.

2 Nos. 162500.00 325000.00

38 MR

STORAGE CABINET

Size 1200X600X850mm

Top of 16Swg S.S.Sheet one over shelf,

three sides of 20SWG s.s. sheet. Dish

storage cabinet with 2 shelves and sliding

door will be provided on service side.

2 Nos. 60000.00 120000.00



MR

Sr.No


Boq / MR

39 MR

STORAGE RACK

Size 900X450X1800

Vertical of 32 mm dia stainless steel pipe

with adjustable feet 4 no of 18 S.S Sheet

at equaly distance.

6 Nos. 39000.00 234000.00

40 MR

INGREDIENT BINS

Size 600X600X600mm

Made of S.S. 18 SWG WITH TOP

HINGE OPENABLE DOORS SUPPORT

WITH FOUR NOS. OF CASTORS, anti

crack body, top half hinged lid. Provided

with a scoop.

4 Nos. 26000.00 104000.00

41 MR

DUNNAGE RACK

Size 1200X600X500mm

Made of s.s.square pipes of size

32x32mm, with support of 25mm

square s.s.pipe.

2 Nos. 27000.00 54000.00

42 MR

POT RACK-3 TIER

Size 1200X600X1500mm

Verticals of 32mmX32mm square

s.s.pipe, 3 shelves welded with vertical

frame of 19mm dia s.s.pipe shelves

with equal space between two tubes

mounted on adjustable feet.

2 Nos. 39000.00 78000.00

43 MR

SOILED DISH LANDING TABLE

WITH GARBAGE CHUTE

Size 2400x600x850mm

Top of 16G s.s.sheet with 'Sunkun'

top. A garbage chute provided on top

with a space below to keep dust bin

(Not part of equipment). The top will be

mounted on m.s.anlge, rust proof

painted & s.s.vertical tubular legs with

cross bracing support on 3 sides

1 No. 80000.00 80000.00

44 MR

THREE SINK UNIT

Size 1800x600x850+150mm

Top & 3 sink bowls of 16G s.s.sheet.

Duly welded, grinded & polished smooth

mounted on m.s.anlge & s.s.tubular

frame work with 150mm back splash.

Each Sink Bowl Size 500x500x300mm

(without sanitory fittings)

1 No. 85000.00 85000.00



MR

Sr.No


Boq / MR

45 MR

CLEAN DISH TABLE

Size2100x600x850mm

Specification same as that of work table

but with 2 undershelves.

1 No. 77000.00 77000.00

46 MR

CLEAN DISH RACK

Size 900x450x1800mm

Vertical of 32 mm dia stainless steel pipe

with adjustable feet 5 no vertical at equal

distance 1st shelf fixed at 150mm from

floor level.

5 Nos. 39000.00 195000.00

47 MR

L.P.G GAS PIPE LINE (150 RUNNING

FEET APPROX)

ACTUAL MEASUREMENT WILL BE

ACCORDING TO As per site conditions

1 No. 236250.00 236250.00

48 MRCENTRIFUGAL EXHAUST BLOWER

20000 CFM1 No. 330000.00 330000.00

49 MR

S.S GRATING for kitchen drainage trough

(APPROX 25 RUNNING FEET)



25 RFT 6000.00 150000.00

50 MR

EXHAUST HOOD DUCTING (APPROX

1200 SQUARE FEET)



1 No. 285000.00 285000.00

5,728,750.00TOTAL



MR


commissioning etc as

required for the follwing items

required for the Laundry.

1 MRTUMBLE DRIER

CAPACITY : 30 KG HEATING: STEAM 1.00 No 160000.00 160000.00

2 MR

FLAT WORK IRONER

ROLLER LENGTH: 2000MM ROLLER

DIA: 600 MM HEATING : STEAM1.00 No 610000.00 610000.00

3 MRWASH ROOM TROLLEY

Size: 1000 x 600 x 780 ht.2.00 Nos 18900.00 37800.00

4 MRDRY LINEN TROLLEY

Size: 1100x600x1500ht2.00 Nos 19600.00 39200.00

5 MRSHELF TROLLEY

Size: 1200x600x1700ht1.00 No. 22500.00 22500.00

6 MRMOBILE TABLE

Size: 1150x7501.00 No. 18000.00 18000.00

7 MR

VACUUM FINISHING TABLE

Size: 1200 x 750

With Steam Iron

2.00 No 45000.00 90000.00

8 MRWASHER EXTRACTOR CAPACITY :

30 Kgs HEATING: STEAM2.00 No 520000.00 1040000.00

9 MRAIR COMPRESSOR

2 HP Single Stage, 100 ltrs. Tank1.00 No 97000.00 97000.00

10 MR

OIL FIRED BOILER WITH SOFTNER

Capacity : 200 Kgs 1.00 No 474500.00 474500.00

11 MR Piping 1.00 Set 125000.00 125000.00

12 MR

Flat Bed Press - penumatic,

automatic, steam heated, automatic

digital timed powerful moisture

suction boiler. Penumatic raising

and lowering of spring suspended

and teflon line head, adjustable

irponing pressure head size

1500x750

1.00 No 279502.00 279502.00

13 MR

laundary scrub station with two

sinks - all ss size 1600x550x900 ht 1.00 No 85653.00 85653.00

3,079,155.00TOTAL


SCHEDULE ITEMS (LAUNDRY)- BOQ

Sr.N

o.Code Description

Unit As Per

Boq/


Quantity Rate As Per

Boq/

Revison I

MR Amount

1 MR


commissioning etc as required for Medical

Call System:

1a MR

Part - A : Medical Gas System.

Supply, Installation, Testing, Commissioning

and Handing Over of Medical Air Compressor

unit of 2 Nos (1 working and 1 standby) non

lubricated reciprocating air cooled air

compressors ( Ingersoll Rand , Anestiwata,

Kirloskar Make) with 60 CFM refrigerant

type air drier with Prefilter, After filter, 20

HP TEFC cage motors, drive package,

suction air filters, starter, mounting base

frame complete with Air colled after cooler,

Pressure Reducing Station. The operation

of the compressors shall be having auto

cutoff system according to the preset

pressures for the lower and upper limit.

The system shall have all the necessary

controls like pressure switches, relief valves,

etc. including Supply, Installation, testing,

commissioning and handing over of Air

receiver for the above compressors with

a storage volume of 2000 ltrs at NTP

conditions.

1.00 Set 1000000.00 1000000.00

1b MR

Three stage Breathing Air Filtration System

( Imported ) with By pass pipeline system

with Isolation Valves.

1.00 Set 200000.00 200000.00


SCHEDULE ITEMS ( Medical Gas System) - BOQ

Sr.N

o.Code Description Unit



Boq/

Revison I

MR Amount

Sr.N


2.a MR


and Handing Over of Medical Vacuum

Pump Unit reciprocating type ( Ingersoll

Rand, Kirloskar Make ) comprising of 2 Nos

vacuum pumps ( 1 working and 1 standby )

with 10 HP TEFC cage motors, drive

package, bacterials filter at the discharge,

mounting base frame complete. The

operation of the vacuum pumps shall be

having auto cutoff arrangement according

to the preset pressures for the lower

and upper limit. The system shall have

all necessary controls like pressure switch,

etc. including Supply, Installation, Testing,

Commissioning and Handing over of

Receiver for the vacuum pumps with a

storage volume of 2000 ltrs at NTP

conditions.

1.00 Set 900000.00 900000.00

2.b MR

Bacterial Filter Vacuum ( Imported ) with

By pass pipeline system with

Isolation valves.

1.00 Set 250000.00 250000.00

3.a MR


and Handing over of Oxygen Manifold

comprising of 2 x 10 Oxygen cylinders in the

main manifold and 2 x 4 cylinders in the

emergency manifold with Piston type Heavy

duty, High flow Oxygen Regulator.

1.00 Set 175000.00 175000.00

3.b MRFully Automatic Oxygen Control

Panel Pneumatically operated. (Imported )1.00 Nos 300000.00 300000.00

4.a MR

Supply, Installation, Testing,

Commissioning and Handing over of

Nitrous Oxide Manifold comprising of 2 x 3

N2O cylinder in the main manifold with a 2

cylinders in the Emergency manifold.

1.00 Set 56500.00 56500.00

4.b MRFully Automatic Nitrous Oxide Control

Panel Pneumatically operated. ( Imported )1.00 Nos 325000.00 325000.00

5 MR

AGSS System consisiting of Duplex, Skid

Mounted AGSS Pumps with Remote Switches

- AGSS Simplex Start Switch. ( Imported )

1.00 Set 2000000.00 2000000.00



Boq/

Revison I

MR Amount

Sr.N


6 MR


and Handing over of Solid drawn copper

pipes manufactured as per BS 2871 - EN

1057 duly certified by LLoyds with all

necessary fittings, pipe supports, etc

complete.

0.00

a). 12 mm OD x 0.7 mm thk 805.00 RMT 300.00 241500.00

b). 15 mm OD x 0.9 mm thk 2650.00 RMT 500.00 1325000.00

c). 22 mm OD x 0.9 mm thk 815.00 RMT 800.00 652000.00

d). 28 mm OD x 0.9 mm thk 285.00 RMT 1200.00 342000.00

e). 54 mm OD x 1.2 mm thk 90.00 RMT 3600.00 324000.00

7 MR


and Handing over of Valve Boxes with

pressure gauges.

0.00

a). 5 Gas Service 6.00 Nos 15000.00 90000.00

b). 4 Gas Service 2.00 Nos 12000.00 24000.00

c). 3 Gas Service 5.00 Nos 10000.00 50000.00

d). 2 Gas Service 17.00 Nos 7000.00 119000.00

8 MR


and Handing over of Isolation Ball valves

for the pipelines complete with

supports, etc. These quantities do not

include the valves in the equipment

room, which shall be quoted as included

in the equipment as specified above.

0.00

a ). 1/2" 50.00 Nos 2000.00 100000.00

b). 3/4" 20.00 Nos 2800.00 56000.00

c). 1" 1.00 Nos 3500.00 3500.00

d). 2" 1.00 Nos 7500.00 7500.00

9 MRSupply, Installation. Testing, Commissioning

and Handing over of Area Line Pressure Alarm0.00



Boq/

Revison I

MR Amount

Sr.N


a). 5 Gas Alarm 5.00 Nos 50000.00 250000.00

b). 4 Gas Alarm 1.00 Nos 45000.00 45000.00

c). 3 Gas Alarm 4.00 Nos 40000.00 160000.00

d). 2 Gas Alarm 4.00 Nos 35000.00 140000.00

10 MR


and Handing over of Gas outlets Points

with Matching Probes (Imported ).

0.00

a). Oxygen Outlet 152.00 Nos 5000.00 760000.00

b). Nitrous Oxide Outlet 24.00 Nos 5000.00 120000.00

c). Compressed Air Outlet ( 4 Bar ) 62.00 Nos 5000.00 310000.00

d). Compressed Air Outlet ( 7 Bar ) 11.00 Nos 5000.00 55000.00

e). Vacuum Outlet 152.00 Nos 5000.00 760000.00

f). AGSS Outlet 5.00 Nos 6000.00 30000.00

11 MR

Electrical Control Panel Equipped along

with Duplex & Cascade system for Air

compressor & vacuum Pump System

1.00 Set 250000.00 250000.00

Part A - Total 0.00

MEDICAL GAS B SYSTEM: 0.00


commissioning etc as required for

Medical Call System:0.00

1 MR

Part - B : Pipeline Accessories.

Back pressure Compensated Oxygen

flowmeters with a range of 0 - 15 LPM. The

body shall be made of brass and chromium

plated. The flow tube shall be of clear,

impact resistant polycarbonate. The

humidifiers bottles shall be made of

breakable polycarbonate and are

autoclavable at 134 Deg C. The meters and

humidifiers shall be suitable for the outlets

offered.

152.00 Nos 1500.00 228000.00



Boq/

Revison I

MR Amount

Sr.N


2 MR

Ward Vacuum Units with unbreakable

collection jars and regulators. The unit shall

be supplied with vacuum guage to indicate

the suction supplied to the unit. The unit shall

have a bracket for wall mounting. The jars

shall be made of unbreakable polycarbonate

and are autoclavable at 134 Deg C.

152.00 Nos 4000.00 608000.00

3 MR

Theatre Vacuum Units on mobile trolleys with

twin 2000 ml unbreakable bottles made

of polycarbonate, autoclavable at 134

Deg C. The unit shall be supplied with a

regulator with instant ON/OFF switch

and three way selection to use the left,

right or both the bottles. The complete

unit shall be mounted on a trolley with castor

wheels.

12.00 Nos 8000.00 96000.00

4 MRConversion Kits for Oxygen with HP Tubing

6.00 Nos 2500.00 15000.00

5 MRConversion Kits for Nitrous Oxide with HP

Tubing6.00 Nos 2500.00 15000.00

MEDICAL GAS C SYSTEM: 0.00


commissioning etc as required for

Medical Call System:

0.00

1 MR

Part - C : Bed Head Wall Panels 1 meter

length

Supply, installation and providing wiring and

piping connections for bed head wall

panels. The panel shall be fabricated out

of high strengths extruded alluminium

sections with inbuilt single railing and

powder coated to color as per the Owners

choice. The panel shall have facility to

accomodate : Max. 5 nos of Gas outlets,

5/15 A multi pin switched socket outlets -

4 nos, 1 no Nurse call switch panel with

wired remote, 1 no arm lamp 60W with

adaptor, 1 no Infusion pump rail mount

pole with adaptor, 1 no IV tree rail mount

with adaptor and holder for vacuum

collection jar To be included with OT

Equipments

146.00 Nos 25000.00 3650000.00

Part C - Total

16,033,000.00TOTAL


Sr no Description UnitTOTAL

OTYRATE AMOUNT

220 MR Providing of signages, modular curved frame

technology,of various widths and lengths, to form

suggested usages,made of aluminium extruded

sections , duly anodised ,all signages shall be

provided with 0.6-0.8mm polycarbonate

protecting film over the prints, of appropriate size,

Model : Illusion by SIGNSUTRA or Equivalent.

Way finding Signs

Way finding ceiling hung sign(both side) 1200x300 each 30 17592 527760.00

Toilets

Toilet Wall Projected(Gents, Ladies, Handicap,

Patient both side)

250x210 each 31 3832 118792.00

Toilet Door mounted(Gents, Ladies, Handicap,

Patient both side)

120x150 each

35755

26425.00

Cubical Plates 120x150 each 99 755 74745.00

Change room with Toilet (Gents, Ladies & Nurse)

Wall Projected (both Side)

250x210 each 13 3832 49816.00

Dress /Janitor closet 120x150 each 10 755 7550.00

Name plate

Number plate 80x120 each 115 358 41170.00

Room designation 80x300 each 133 691 91903.00

Doctor's/ Occupant's name 80x300 each 37 691 25567.00

Wall mounted over Door 150x600 each 70 3621 253470.00

Nurse Station 0

Wall projected(both side) 250x210 each 6 3832 22992.00

Door mounted 120x150 each 8 755 6040.00

Radiography/MRI/CTScan etc.

Wall projected(both side) 250x210 each 4 3832 15328.00


Waiting Lounge

Wall mounted 150x600 each 13 3621 47073.00

Others

Lifts (Elevators nos.) 400x120 each 20 2416 48320.00

Lifts Wall Projected 250x210 each 10 3832 38320.00

Stairs Wall Projected(both side) 250x210 each 19 3832 72808.00


Drinking Water 400x120 each 10 2416 24160.00

Electric / AHU rooms 400x120 each 5 2416 12080.00

Bed number in more than 2 bedded rooms 80x120 each 174 358 62292.00

Schedule of Items- Signage - BOQ

Name of Work- Construction of 100 Bedded Hospital for ESIC Bhilai



OTYRATE AMOUNT

221 MR Providing of prohibition and general

signage,made of 0.8mm thick aluminium

sheet duly painted with Polyurethene paint of

approved make and shade, aluminium sheet

bented to form a curve , and supported by

moulded plastic components to hold the

curve , the moulded plastic components to be

fixed on aluminium rails with clip on arrangment,

as per the product design of model: POLKA,

manufectured by Signsutra

or equivalent.

Directory at Lift Lobby

Floor(levels) 385x385 each 10 4076 40760.00

Department 385x385 each 20 4076 81520.00

Registeration/Reception etc. 0

Ceiling hung over counter(both sides) 750x235 each 6 13864 83184.00

Department Direction 0

Wall mounted 600x320 each 20 4946 98920.00

Corner mounted 2x600x320 each 0 9892 0.00

Department Name 0

Ceiling hung (both sides) 1000x235 each 0 18342 0.00

Waiting Lounge 0

Ceiling hung (both sides) 1000x235 each 0 18342 0.00

Providing and fixing prohibition signage , made of

Aluminium composite panel and all text and

pictograms as screen orinted and malamine

coated, all fixtures in 304 grades SS, all designs as

per architect approval

Silent Zone 200x200 each 40 787 31480.00

No Smoking 200x200 each 50 787 39350.00

Safety Notice- be kept clear to Emergency carts 200x200 each

25787

19675.00

222 MR Providing of Snap fit frames,made of aluminium

extruded profiles duly anodized , and shall be also

provided with .8mm thick polycarbonate film to

protect /hold the insertions. And 8mm thick

MDF, as main

inserion panel.

SNAP FIT FRAMES 450x600 each 50 3933 196650.00

223 MR Providing of 1.5mm,polished,304 grade,Stainless

steel plate, duly etched and filled with prescribed ELEVATOR DISCLAIMER PLATE 250x250 each 10 2360 23600.00



OTYRATE AMOUNT

224 MR Providing of edge lit ,emergency exit sign with 2

hrs power back up, concealed in false ceiling,of

PROLITE AUTOGLO make

or equivalent

LED SIGN (CONCEALED)with 2hr backup standard each 41 8296 340136.00

EXIT LIGHT WITH 2 HR BACKUP(Exit at

Stairs entry/ Deptt. Exit)

standard each

216794

142674.00

225 MR Providing of Photoluminescent,

1mm rigid pvc based sheet containg lumingen

3, as base chemical,with high intensity luminous

glow capacity.

PHOTOLUMINESCENT SIGN , FIRE HOSE 250x200 each 25 1831 45775.00

PHOTOLUMINESCENT SIGN,ESCAPE SIGN 400x150 each 60 2197 131820.00

PHOTOLUMINESCENT SIGN,FIRE ALARM CALL

POINT

200x150 each

251098

27450.00

PHOTOLUMINESCENT SIGN, EVACUATION PLAN 300x200 each 17 2912 49504.00

PHOTOLUMINESCENT SIGN,PULL AND PUSH 90mm DIA each 104 292 30368.00

226 MR Providing of internally illuminated signage made

with CNC cut ACP(aluminium composite

panel)with insertions of text and pictogram of

10mm thick laser cut acrylic, duly cladded with

electrocut casted 3M vinyl of required color,

illumination by GE or Phillips LED, as per Design.

Radiography/MRI/CTScan etc.

In use (illuminated) 400x400 each 3 9726 29178.00

231 MR Providing of Floor Directory (TOTEM) of size

measuring 1500mmx3000mm in the main

entrance Lobby/ Foyer fabricated with MS rigid

sections of allied sizes to design developed by M/S

SIGNSUTRA.

Floor Directory (TOTEM) 1500x3000 each 5 57607 288035.00

232 MR Providing of Main Directory assembeled with

standard alluminium alluminium extruded plates,

duly anodized.The plates shall be of size 1no. of

1000x120mm as top subject plate and

10nos. 1000x100 mm contents plates. Each of the

plates shall be provided with 0.8 mm thick

polycarbonate protecting film over the printed

text. model: Illusion by SIGNSUTRA or equivalent.

Main Directory 1000x1120 each 1 352 352.00



OTYRATE AMOUNT

233 MR Providing of Main Directory assembeled with

standard alluminium alluminium extruded plates,

duly anodized.The plates shall be of size 1no. of

1000x120mm as top subject plate and

10nos. 1000x100 mm contents plates (inclusive of

Dr.'s name and 'In''Out' sections). Each of the

plates shall be provided with 0.8 mm thick

polycarbonate protecting film over the printed

text. model: Illusion by SIGNSUTRA or equivalent.

Doctors' Directory 1000x1120 each 1 35254 35254.00

238 MR Providing of Evacuation floor plans measuring

500mmx 600mm made of 5 mm foam board and

1mm thick rigid plastic photoluminiscent printed

plans framed into

45mmx 20 mm extruded aluminium tubuklar

frame with necessary holding slots.

Evacuation Plans Floor wise 500x600 each 36 9297 334692.00

239 MR Providing of Entrance Gate External Signage as per

design developed by SIGN SUTRA

TOTAL 3654353.00


S.N. DESCRIPTION UNITQTY RATE AMOUNT

1High speed high pressure horizontal cylinder

steam sterlizerNOS.

1 844590844590

Nat steel high speed high pressure horizontal

cylindrical Steam sterllizer.Operating pressure will

be 30 ps. Corresponding to a temp. of 134.

2 s.s work table NOS. 1 75278 75278

Table is used for wet goods with underself.

3 S.S vertical sliding door NO. 1 114134 114134

Door is used between clean and dirty areas in

hospitals,pharmaceuticals etc.

4 S.S. control and packing table with drawer NO. 1 251090 251090

Table with drawer is used for seperation,control

and packing of various sets of sterlized.

5 s.s work table with two sink NO. 1 194978 194978

The bench top is fabricated out of 16 swg ss 304.

6 Washer disinfector NO. 1 1133732 1133732

Washer disinfector,single door,suitable for

cleaning .

7 Ultrasonic Cleaner NO. 1 540233 540233

Ultrasonic Cleaner of overall size 530x330x350.

8 Drying cabinet with single door NO. 1 677195 677195

Digital timer controlled drying cabinet with the

single door suitable for easy and quick drying of

instrument.

9 Stainless Steel work table NO. 1 75278 75278

Table is used for wet goods with underself.

10 Stainless Steel racks with 5 shelves NOS. 1 144571 144571

Total 4051079


Schedule of Items-TSSU EQUIPMENTS- BOQ


Sl.no. DSR-16 Description of items Unit QTY Rate Amount

SUB HEAD : I. WIRING AND SUB MAINS

1.01 1.3.3

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

recessed steel conduit, with modular switch,

modular plate, suitable GI box and earthing the

point with 1.5 sq.mm FRLS PVC insulated copper

conductor single

core cable etc. as required.

point 1108 1037 1148996

1.02 1.10.2

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

recessed PVC conduit, with modular switch ,

modular plate, suitable GI box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.for

Housing

point 777 615 477855

1.03 1.4

Wiring for twin control light point with 1.5 sq.mm

FRLS PVC insulated copper conductor single

core cable in surface /recessed steel conduit, 2

way modular switch, modular plate,suitable GI box

and earthing the point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc.

as required.( Lift well )

point 20 1094 21880

1.04 1.11

Wiring for twin control light point with 1.5 sq.mm

FRLS PVC insulated copper conductor single

core cable in surface /recessed medium class

PVC conduit, 2 way modular switch, modular plate,

suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor

single core cable etc. as required.( FOR

COMMON SERVICE )for Housing

point 22 809 17798

1.05 1.54

Wiring for group controlled (looped) light point / fan

point / exhaust fan point/ call bell point (without

independent switch etc.) with1.5 sq. mm FRLS PVC

insulated copper conductor single core cable in

surface/ recessed steel conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc. as required.-group-

C

point 843 601 506643

1.06 1.55.3

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable

in surface/ recessed PVC conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc. as required. ( FOR

COMMON SERVICE )for Housing

point 67 415 27805

PROJECT: PROPOSED 100 BED ESIC HOSPITAL AT BHILAI, CHHATTISGARH.

BOQ FOR ELECTRICAL WORK IN ESIC HOSPITAL, BHILAI



1.07 1.7.2

Wiring for circuit/ submain wiring alongwith earth

wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in

surface/ recessed steel conduit as required. 2 X

2.5 sq. mm + 1 X 2.5 sq. mm earth wire

mtrs 7110 206 1464660

1.08 1.14.2

Wiring for circuit wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper

conductor, single core cable in surface/ recessed

PVC conduit as required - 2 x 2.5 sq. mm + 1x 2.5

sq. mm earth wire

mtrs 1408 137 192896

1.09 1.7.2





2.5 sq. mm + 1 X 2.5 sq. mm earth wire (for LIGHT

PLUG )

mtrs 10188 206 2098728

1.10 1.14.1





sq. mm earth wire ( FOR COMMON SERVICE )

mtrs 120 112 13440

1.11 1.7.2





2.5 sq. mm + 1 X 2.5 sq. mm earth wire (for FCU )

mtrs 2180 206 449080

1.12 1.14.2





sq. mm earth wire for LIGHT PLUG for Housing

mtrs 1840 137 252080

1.13 1.7.3

Wiring for power plug with 2X4 sq. mm FRLS PVC


surface/ recessed steel conduit alongwith 1 No 4

sq. mm FRLS PVC insulated copperconductor

single core cable for loop earthing as required.

mtrs 1810 237 428970

1.14 1.14.3

Wiring for power plug with 2X4 sq. mm FRLS PVC


surface/ recessed PVC conduit alongwith 1 No 4

sq. mm FRLS PVC insulated copperconductor

single core cable for loop earthing as required. for

Housing

mtrs 2192 168 368256

1.15

Wiring for sub main wiring with the following

sizes of PVC insulated, copper conductor, cable

in surface /recessed steel conduit as required.

a) 1.7.104 X 10 sq. mm + 2 X 6 sq. mm earth wire for floor

panel to DB mtr 1110 653 724830

b) 1.7.114 X 16 sq. mm + 2 X 6 sq. mm earth wire for floor

panel to DB (for 12 WAYmtr 1620 930 1506600



1.16

Wiring for sub main wiring with the following

sizes of PVC insulated, copper conductor, cable

in surface /recessed PVC conduit as required. for

Housing

a) 1.14.52 X 10 sq. mm + 1 X 6 sq. mm earth wire (TYPE-

II & TYPE-III)mtr 426 299 127374

b) 1.14.104 X 10 sq. mm + 2 X 6 sq. mm earth wire for floor

panel to DB for Type-IVmtr 204 536 109344

1.17

1.24.1+1

.24.4+1.

27.2

Supply and fixing suitable size GI box with modular

plate and cover in front on surface or in recess,

including providing and fixing 3 pin 5/6 & 5/6 amps

modular socket outlet and 5/6 amps modular

switch, connection, painting etc as required.

each 941 350 329350

1.18

1.24.1+1

.24.4+1.

27.2



including providing and fixing 3 pin 5/6 & 5/6 amps


switch, connection, painting etc as required.for FCU

& Inline fan

each 109 350 38150

1.19

1.27.4+1

.24.4*2+

1.24.1



including providing and fixing two nos 3 pin 5/6 &

5/6 amps modular socket outlet and one 5/6 amps

modular switch connection , painting etc as

required.for TV power & Computer point

each 191 504 96264

1.20

1.24.3+1

.27.2+1.

24.5



including providing and fixing13 Amp universal


switch, connection, painting etc as required.

each 608 454 276032

1.21

1.27.5+1

.24.4*3+

1.24.1



including providing and fixing three nos 3 pin 5/6

& 5/6 amps modular socket outlet and 5/6 amps

modular switch, connection , painting etc as

required.for ups power

each 200 624 124800

1.22 2.18

Supplying and fixing 20 A, 240 V, SPN Industrial

type socket outlet, with 2 pole and earth, metal

enclosed plug top alongwith 20 A, “C” curve, SP,

MCB, in sheet steel enclosure, on surface or in

recess, with Chained metal cover for the socket out

let and complete with connections, testing and

commissioning etc. as required. for AC +gyeser for

Housing

each 40 980 39200

1.23 1.25

Supplying and fixing stepped type electronic fan

regulator on the existing modular plate switch box

including connections but excluding modular plate

etc. as required.

each 390 288 112320



1.24

(DSR

Civil-

2014,

Item no.

10.18)

Providing and fixing circular/ Hexagonal GI box for

ceiling fan clamp, of internal dia 140 mm, 73 mm

height, top lid of 1.5 mm thick GI sheet with its top

surface hacked for proper bonding, top lid shall be

screwed into the GI box by means of 3.3 mm dia

round headed screws, one lock at the corners,

clamp shall be made of 12 mm dia M.S. bar bent to

shape as per standard drawing. Rate to be taken

each 390 143 55750.5

1.25 MR25 amp DP MCB in IP 65 box (outdoor type) for AC

Outdoor Unit)each 2 2127 4254

Total carried over to summary Rs. 11013355.50

SUB HEAD-II CONDUIT PIPES AND METAL BOXES FOR

AND OTHER SERVICES.

2.01

Supplying and fixing of Following sizes of

PVC conduit along with the accessories like

Junction boxes, bends, socket, fish wire etc. on

surface/recess with M.S. Clamps, nuts and

bolts including cutting of the wall and making

good the same in case of recessed conduit as

required. for LV

a) 1.21.1 20mm mtr 580 57 33060

b) 1.21.2 25mm mtr 6712 69 463128

c) 1.21.3 32mm mtr 1080 89 96120

d) 1.21.4 40mm mtr 230 114 26220

2.02

Supply, fixing, connecting and testing of

telephone / computer / TV modular sockets

modular plate anodised MS box and blanking

plate in surface / recessed including connectionetc

as required.

a) 124.6+1

27.1

RJ-11 telephone socket two line with shuttereach 168 271 45528

b) 124.7+1

27.1

T.V. CO-axial cable socket outlets of one point each 46 272 12512

2.03

Supplying and fixing following size/ modules, GI

box alongwith modular base & cover plate for

modular switches in recess etc. as required.

1.27.2 3 Module (100 mmX75 mm) for existing RJ 45 each 182 185 33670

2.04

Providing, fixing connecting and testing of

solder less telephone tag block of following

capacity ties as required in suitable size of

m.s. hinged lockable cover box duly painted

etc. as required of Krone type.

a) MR 10 pair Tele Tag Blk. each 11 900 9900

a) MR 50 pair Tele Tag Blk. each 5 3000 15000

b) MR 100 pair Tele Tag Blk. each 2 4500 9000

2.05

Supplying and drawing following pair, 0.5 sq.mm

FR PVC insulated coper conductor, unarmoured

telephone cable in existing surface / recessed steel

/ PVC conduit as required.

a) 1.18.2 2 pair Telephone cable. (0.5sq mm) mtr. 7200 19 136800

b) MR 10 pair Telephone cable mtrs 1000 95 95000



2.06 1.19

Supplying and drawing co-axial TV cable RG-6

grade, 0.7 mm solid copper conductor PE

insulated, shielded with fine tinned copper braid

and protected with PVC sheath in the existing

surface/ recessed steel / PVC conduit as required.(

for TV )

mtr. 970 29 28130


SUB HEAD-III DISTRIBUTION BOARD

3.01

Supplying and fixing following way, horizontal type

three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess,

complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But

without MCB / RCCB / Isolator)

3.01 a) 2.4.1 4 way (4 + 18), Double door each 4 2198 8792

3.01 b) 2.4.2 6 way (4 + 18), Double door each 14 2659 37226

3.01 c) 2.4.3 8 way (4 + 24), Double door each 27 3171 85617

3.02

vertical type, 415 V, TPN MCB distribution board of

sheet steel,dust protected, duly powder painted,

inclusive of 200 A, tinned copper bus bar,

common neutral link, earth bar, din bar for

mounting MCBs (but without MCBs and incomer)

as required.

2.5.3 12 way (4 + 36), Double door for Power DB each 54 7189 388206

3.03

Supplying and fixing following way, single pole and

neutral, sheet steel, MCB distribution board, 240

V, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din

bar, interconnections, powder painted including

earthing etc. as required. (But without MCB / RCCB

/ Isolator)

a) 2.3.1 6 way, Double door for COMMON each 7 942 6594

b) 2.3.3 12 way, Double door for TYPE-II & TYPE-III each 24 1151 27624

3.04 N.S.R.

Supplying and fixing of following ways surface/

recess mounting, vertical type, 415 V, TPN MCB ,

distribution board with MCCB incomer of sheet

steel, dust protected, duly powder painted, inclusive

of 200 A, tinned copper bus bar, common neutral

link, earth bar, din bar for mounting MCBs (but

without MCBs and incomer) as required. (Note :

Vertical type MCB TPDB is normally used where 3

phase outlets are required.) as Light, power, UPS

Floor DB

3.04 a) N.S.R. 8 way (4 + 24), Double door ( for LIGHT +UPS) each 12 21575 258900

3.04 b) N.S.R. 12 way (4 + 36), Double door ( for POWER ) each 6 22343 134058

Incomer :-

3.05

Supplying and fixing upto 32 amps rating, 240/415

volts, “C”curve, miniature circuit breaker suitable for

inductive load of following poles in the existing MCB

DB complete with connections,testing and

commissioning etc. as required.



3.05 a) 2.10.5 Triple pole and neutral 32 amp for Light DB each 61 891 54351

b) 2.10.1 6-32 Amp (10 KA) SP MCB C' Series each 2668 173 461564

c) 2.10.3 Double pole each 27 463 12501

d) N.S.R. 40A FP MCB each 18 3008 54144

e) N.S.R. 63A FP MCB each 73 3008 219584

3.06

Supplying and fixing following rating, double pole,

(single phase and neutral), 240 volts, residual

current circuit breaker (RCCB),having a sensitivity

current upto 300 milliamperes in the existing MCB

DB complete with connections, testing and

commissioning etc. as required.

RCCB's :-

a) 2.14.363 Amp SPN RCCB with 30 ma fault current rating

(1 No. per phase) for L+P- DBeach 168 2242 376656

a) 2.14.240 Amp SPN RCCB with 30 ma fault current rating

(1 No. per phase) each 48 1719 82512

b) 2.15.240 Amp 4P RCCB with 30 ma fault current rating

for M/C Roomeach 2 2131 4262

b) 2.14.125 Amp SPN RCCB with 30 ma fault current rating

(1 No. per phase) each 1 1650 1650

3.07

Providing and fixing following rating and breaking

capacity and pole MCCB with thermomagnetic

release and terminal spreaders in existing cubicle

panel board including drilling holes in cubicle panel,

making connections, etc. as required.

a) 2.2.1100 A, 16 kA,TPMCCB for (G+IV+1Floor) -UPS &

LDB each 12 3218 38616

b) 2.2.2 125 A, 16 kA,TPMCCB for (G+IV+1Floor) -L DB each 3 3613 10839

c) 2.2.3150 A, 16 kA,TPMCCB for (G+IV+1Floor) -P DB

each 2 4096 8192

d) 2.2.5200 A, 25 kA,TPMCCB for (G+IV+1Floor) -P DB

each 4 7964 31856

OT ISOLATION PANEL

3.08

Supply only of Indoor, cubical, wall mounted. With

IP 42 protection , 10 KVA ISOLATION

Transformer , single phase 230 Volt air cooled

ISOLATION Panel for OT with following specs

each 3 419750 1259250

3.09

Receiving,installation, testeng ,commisioning of

Indoor, cubical, wall mounted. With IP 42 protection

, 10 KVA ISOLATION Transformer , single phase

230 Volt air cooled ISOLATION Panel for OT with

following specs

each 3 2875 8625

RISING MAIN



3.10

Supplying, installing on wall, testing and

commissioning of following capacity Air Insulated

Compact Type Rising Mains for use on 3 phase 4

wire 415 V, 50Hz A.C. supply with enclosure

having IP-54 rating after fixing the tap off boxes

and all accessories, made of 1.6mm thick steel

sheet duly powder coated in convenient sections

complete with 4 Nos. aluminium bus bars having

current density of 130 A/ sq cm at nominal

current rating, necessary joints & expansion joints,

fire barrier at each floor, provision of tapping at

every meter, continuous earthing with 2 Nos.

aluminium strip of suitable size (one on each side)

including, G.I. clamping brackets, angle iron

bracket, steel fasteners, connecting to earthing

system etc. as required.

3.8.2 315 A, Isc = 25 kA for 1 second Mtr 21 5806 121926

3.11

Supplying, installation, testing & commisioning of

following capacity Plug In/ tap off box on the

existing Air Insulated Compact Type bus trunking/

rising mains for use on 3 phase 4 wire 415 V, 50Hz

A.C. supply made with 1.6mm thick sheet steel

enclosure (IP54) duly powder coated with provision

of MCCB (but without MCCB) complete etc. as

required

3.12.1 125 A, Isc = 15 kA for 1 second each 6 4621 27726

3.12

Supplying, installation, testing & commisioning of

following capacity End Feed Unit for the existing

Air Insulated CompactType bus trunking/ rising

mains for use on 3 phase 4 wire 415V, 50Hz A.C.

supply made with 1.6mm thick steel sheet

enclosure (IP54) duly powder coated with provision

of MCCB/ ACB (but without MCCB/ACB) complete

with necessary joints including clamping brackets,

angle iron bracket, steel fasteners, connecting to

earthing system etc. as required

3.11.2 315 A, Isc = 25 kA for 1 second Each 1 4169 4169

3.13

Providing and fixing following rating and breaking

capacity and pole MCCB with thermomagnetic

release and terminal spreaders in existing cubicle

panel board including drilling holes in cubicle panel,

making connections, etc. as required.

i) 2.2.18 400 A, 50kA, FP MCCB for EFU Each 1 19089 19089

ii) 2.2.13 100 A, 30kA, FP MCCB for tap off box Each 6 5360 32160


OT ISOLATION PANEL-SPECIFICATION

1) SYSTEM 230V AC 50Hz Single Phase

2) LOCATION & TYPE Indoor, cubical, wall mounted.

3) ENCLOUSRE IP42

4) ISOLATION PANEL

a) Isolation transformer capacity 10 KVA-PIECO MAKE.

b) Ratio 0.042361

c) Primary Voltage (Volts) 230V

d) Secondary Voltage (Volts) 230V



e) Cooling Air Cooled

f) Winding & type

5) OVERALL DIMENSION 1150mm H X 650mm W X 250mm D

6) INCOMER

a) ELCB HI Type 63A 30 mA. DP –Schneider/Siemens make

b) MCB D Curve 63A DP – Schneider/Siemens make

7) OUTGOING

MCB D Curve 12 Nos. 20A DP – Schneider/Siemens make

8) LINE ISOLATION MONITOR Hazard Index 0-10MA. - PIECO MAKE

9) INDICATION

a) Meter Digital – PIECO MAKE

b) Indicating Lamp Red & Green for Zones

10) COOLING FAN 230V 4 inches

SUB HEAD-IV ERRECTION OF LIGHT & FAN FIXTURES

4.01 1.34Supplying and fixing brass batten/ angle holder

including connection etc. as required.each 3 75 225

4.02 1.33

Supplying and fixing of 3 pin, 5 amp ceiling rose ISI

marked on the existing junction box / wooden block

including connection etc. as required.

each 33 46 1518

4.03 1.38

Supplying and fixing call bell/ buzzer suitable for

single phase,230 volts, complete as required. For

consultant -disply board

each 72 61 4392

4.04 1.39

Providing and fixing plain 16/0.20mm (0.50sqmm)

twin flat flexible,FRLS PVC insulated, copper

cable, in PVC sleeve of suitable size on the floor/

wall, or side of the table/ door etc. as required.

Mtr 1975 22 43450

4.05 1.41

Installation, testing and commissioning of LED Light

Fixture & Exit Light with 1.5 sq. mm FRLS PVC

insulated, copper conductor, single core cable and

earthing etc. as required.

each 2140 100 214000

4.06 1.45

Installation, testing and commissioning of ceiling

fan, including wiring the down rods of standard

length (upto 30 cm) with 1.5 sq.mm FRLS PVC

insulated, copper conductor, single core

cable,including providing and fixing phenolic

laminated sheet cover on the fan box etc. as

required.

each 390 132 51480

FIXING EXHAUST FAN UPTO 450 MM SWEEP

4.07 1.50.1

Installation, testing and commissioning of exhaust

fan up to 450 mm sweep in the existing

opening,including making the hole to suit the size of

the above fan, making good the damage complete

, connection , etc as required.-M/C ROOM &

PUMP ROOM

each 34 224 7616

4.08 1.5.1 Extra for fixing of louvers / shutters complete with

frame for exhust fan of all sizes.each 34 99 3366


SUB HEAD-V SUPPLY OF LIGHT & FAN FIXTURES

Cooper winding Double wound with



5.01 N.S.R.20W LED tubelight -similar to philips cat no-

BN150W LED20S-6500 PSE OD GReach 410 1537 630170

5.02 N.S.R.18W LED tubelight with cover -similar to philips cat

no-BN021C LED20S PSU CDL GReach 253 507 128271

5.03 N.S.R.

15 W surface type LED downlighter -similar to

philips cat no-DN194B LED15S-6500 PSU WH S1 each 174 1220 212280

5.04 N.S.R.

18W recessed type LED downlighter -similar to


5.05 N.S.R.

20 W recessed type LED downlighter -similar to


5.06 N.S.R.

36 W 600mmX600mm LED Light (for minor OT) -

similar to philips cat no-RC383B LED 36S-4000

PSU OD WH PIR

each 6 3226 19356

5.07 N.S.R.

40 W 600mmX600mm LED Tile Light -similar to

philips cat no-RC383B LED 36S-4000 PSU OD WH

PIR

each 149 3226 480674

5.08 N.S.R.Bulk Head LED Light Surface type -similar to C&S

cat no-CG80IB6WLEDeach 61 613 37393

5.09 N.S.R.

1200mm long antibacterial UV Light (for blood

bank) -similar to philips cat no-PHILIPS TUV 36W

+ FITTING

each 6 1008 6048

5.10 Supply of following Ceiling Fan :

a)1200mm Sweep similar to Havells CAT no. - Pacer

each 386 1698 655428

b)1400mm Sweep similar to Havells CAT no. - Pacer

each 4 1816 7264

5.11

Supply of 380mm Heavy Duty Exhaust Fan for

Machine Room including louvers similar to Havells

CAT no. - Turbo force

each 2 3371 6742

5.12 N.S.R. Supplying of Heavy Duty Exhaust Fans

300 mm, 1400 RPM similar to Havells CAT no. -

turbo forceEach 32.00 2815.00 90080

5.13 1.38Supplying and fixing call bell/ buzzer suitable for

single phase,230 V, complete as requiredEach 32.00 61.00 1952

5.14 N.S.R.

Decorative wall mounting fixture with opal glass

diffuser suitable for 12W LED Bulb similar to philips

for type II+Type III - similar to philips Decorative

light fix. GRACE Wall light

each 120.00 821.00 98520

5.15 N.S.R.

Decorative wall mounting fixture with opal glass

diffuser suitable for 12 W LED Bulb similar to

philips for type IV - Decorative light fix. EWC 300

WHIT

each 88.00 1085.00 95480

5.16 N.S.R.

Supply of 10W round shaped surface mounted LED

slim panel, powder coated white finish

housing.similar to polycab cat no PCGLWL 10 R - each 145.00 930.00 134850



5.17 N.S.R.

Supply of 18W round shaped surface mounted LED

slim panel, powder coated white finish

housing.similar to polycab cat no PCGLWL 18 R - each 40.00 1563.00 62520

5.18 N.S.R.

Supply of surface & wall mounted 20 watt LED

TUBE LIGHT with extruded aluminium housing and

robust construction. Similar to philips BN021C

LED20S PSU NW GR

Each 127.00 507.00 64389


SUBHEAD VI :- EARTHING

6.01 5.4

Earthing with G.I. earth plate 600 mm X 600 mm X

6 mm thick including accessories, and providing

masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 meter long

etc. with charcoal/ coke and salt as required.

each 42 4327 181734

6.02 5.6

Earthing with copper earth plate 600 mm X 600

mm X 3 mm thick including accessories, and

providing masonry enclosure with cover plate

having locking arrangement and watering pipe of

2.7 meter long etc. with charcoal/ coke and salt as

required.

each 48 8289 397872

6.03 5.9

Supplying and laying 25 mm X 5 mm G.I strip at

0.50 metre below ground as strip earth electrode,

including connection/ terminating with G.I. nut, bolt,

spring, washer etc. as required. (Jointing shall be

done by overlapping and with 2 sets of G.I. nut bolt

& spring washer spaced at 50mm)

Rmt 260 85 22100

6.04 5.8

Supplying and laying 25 mm X 5 mm copper strip at

0.50 metre below ground as strip earth electrode,

including connection/terminating with nut, bolt,

spring, washer etc. as required. (Jointing shall be

done by overlapping and with 2 sets of brass nut

bolt & spring washer spaced at 50mm)

Rmt 240 595 142800

6.05 5.15

Supplying and laying 25 mm x 5mm G.I. strip on

surface or in recess for connection etc as required. Rmt 1080 129 139320

6.06 5.14

Providing and fixing 25 mm X 5 mm copper strip on

surface or in recess for connections etc. as

required.

Rmt 1000 698 698000

6.07 5.16Providing and fixing 6 SWG G.I. wire on surface or

in recess for loop earthing as required.Rmt 760 37 28120

6.08 5.13

Providing and laying earth connection from earth

electrode with 4.00 mm dia copper wire in 15 mm

dia G.I. pipe from earth electrode including

connection with copper thimble

Rmt 200 182 36400



6.09 5.19

Providing and fixing 4.00 mm dia copper wire on

surface or in recess for loop earthing along with

existing surface/ recessed conduit/ submain wiring/

cable as required.

Rmt 100 73 7300

6.10 5.20

Providing and fixing earth bus of 50 mm X 5 mm

copper strip on surface for connections etc. as

required.

Rmt 128 1283 164224

6.11

(1.14.5-

1.21.2-

1.17.2/2)

/2

Supplying and drawing following sizes of FRLS

PVC insulated copper conductor, single core cable

(GREEN Colour ) in the existing surface /

recessed steel / PVC conduit as required.

10 sq. mm green colour Rmt 300 86 25875

Total carried over to summary 1843745.00

SUBHEAD VII :- LIGHTNING ARRESTOR

7.01 6.2

Providing and fixing of lightning conductor finial,

made of 25 mm dia 300 mm long, G.I. tube, having

single prong at top, with 85 mm dia 6 mm thick G.I.

base plate including holes etc.complete as

required.

each 4 304 1216

7.02 6.4

Jointing copper / G.I. tape (with another copper/ G

I tape, base of the finial or any other metallic object)

by riveting / nut bolting / sweating and soldering

etc. as required.

Each 100 57 5700

7.03 6.7

Providing and fixing G.I. tape 20 mm X 3 mm thick

on parapet or on surface of wall for lightning

conductor complete as required.(For horizontal run)Rmt 250 66 16500

7.04 6.8

Providing and fixing G.I. tape 20 mm X 3 mm thick

on parapet or on surface of wall for lightning

conductor complete as required. (For vertical run)Rmt 160 100 16000

7.05 6.12

Providing and fixing testing joint, made of 20 mm X

3 mm thick G.I. strip, 125 mm long, with 4 Nos. of

G.I. bolts, nuts, chuck nuts and spring washers etc.

complete as required.

each 8 73 584

7.06 6.14

Providing and laying of G.I. tape 32 mm x 6 mm

from earth electrode directly in ground as required. Rmt 100 112 11200

Soil Enhancement Material -ADDITIONAL

Total carried over to summary 51200.00

DETAIL OF EARTHING

(HT PANEL) CU 2

TR -N CU 4

DG -N CU 4

LIFT CU 8

OT CU 6

CSSD CU 2

CATH LAB CU 2

OTHER( UPS,SERVER,X-RAY etc) CU 20

TOTAL NOS OF COPPER EARTHING 48



TR -BODY GI 4

2 POLE Structure GI 2

DG- BODY GI 4

PANEL GI 4

BUILDING GI 4

LA GI 8

OTHER GI 10

TOTAL NOS OF GI EARTHING 36

SUBHEAD - VIII . FIRE ALARM & PA SYSTEM

a) Hospital

8.01

Supply, installation, testing & commissioning of 4

Loop Microprocessor based inteligent and

electronically addressable, modular, expandable

networkable, Panel (expandable) with each loop

capacity of 250 detectors with Loop length up to 3

KM. Fire alarm control panel with 5.7 inch touch

screen LCD display, multiple acess levels, 10,000

event history logs in the non volatile memory

(EEPROM).The panel should be modular

microprocessor based in nature and should be

expandable from single loop to up to 32 loops. The

panel shall have 240V AC power supply, Automatic

battery charger, 24V , ceiled lead acid maintanence

free battries sufficient for 24 hours normal working

and then be capable of operating the system for 30

mins during emergency condtion. Panel shall be

integratable to BMS Backnet software. The panel

shall be EN54/Vds /ULCertification.

Nos. 1 390667.85 390667.85

8.02

supply, Installation, connecting testing and

commissioing of Active and networkable repeater

panel with LCD display complete system function

keys for programming and control like system reset,

alarm acknowledgement, alarm silence, trouble

acknowledgement ...etc. as per specification.

Nos. 1 114369.65 114369.65

8.03 Supply, Installation, Testing and Commissioning of addressable smoke detector including mounting base with LED… etc. complete as required with 2 Isolators (one for incoming and one for outgoing line) integrated in detector for maintaining operational availability of all elements in the loop, even in the event of a short circuit, & Drift Compensation feature & Automatic addressing. Shall be EN54/ VDs/UL certification. Nos. 300 4366.78 1310034

8.04

Supply, Installation, Testing and Commissioning of

addressable Heat detector withfiexed and rate of

raise feature including mounting base with LED…

etc. complete as required with 2 Isolators (one for

incoming and one for outgoing line) integrated in

detector for maintaining operational availability of

all elements in the loop, even in the event of a short

circuit, & Drift Compensation feature & Automatic

addressing. High resistance to electromagnetic

effects in accordance with EFSG agreement

EFSG/F/97/005. Shall be EN54/ VDs/UL

certification. Make : Bosch

Nos. 10 4267.12 42671.2

8.05


addessable manual break glass unit ( Double

action) with flexible network structures & necessary

fixing arrangements with key complete as required.

Shall be EN 54 / Vds/UL Certification. Make: Bosch

Nos. 26 4040.63 105056.38



8.06


Addressable Monitor Module with 3 monitoring

features, monitoring of a line with EOL resistor

,Potential free contact & voltage monitoring. Shall

be EN54 / Vds/UL Certification. Make : Bosch

Nos. 31 5290.86 164016.66

8.07


Addressable Control Relay Module with flexible

network structures with a maximun switching

current of 1A @ 30V DC. Shall be EN54/ Vds

Certification/UL Make : Bosch

Nos. 31 5290.86 164016.66

8.08

Supply,installation,Testing and commissioning of

Responce Indicator Alarm status is indicated By

Red colour LED, Operates on 12 VDC, Dual LED’s

for 360deg visibility, Flush / Ceiling wall mount,

Operating Voltage : 12 VD.C, Operating Current :

10mA, Alarm Indication : RED LED with required

accessories

Nos. 100 1041.87 104187

8.09


Stand alone Loop Powered detector base sounder

with 32 different tone variants selection options &

adjustable sound pressure by 5 levels, the sound

pressure 92.1 dB(A), with flasher having

Synchronized flash rate of 1 Hz and Light intensity

> 2 cd, should be programmed from the panel.

Shall be EN54 / Vds/UL Certification.

Nos. 1 10251.05 10251.05

8.10

Supply,Installation,Testing and Commissioning of

Voice Alarm Call Station having gooseneck

condenser microphone with 6 zone Selection Keys

and an All-Call-Key, PTT Switch, selectable gain,

speech filter and limiter for improved intelligibility,

LED indication for zone selection, fault and

emergncy state, Complete as required (Similar to

Bosch Cat. No. LBB 1956 or equivalent)

Nos. 1 29398.73 29398.73

8.11


Voice Alarm Controller having features like

announcement to 6 zones expandable to 60 zones,

built in 240W booster amplifier, emergency

microphone on the front panel, 16 priority levels

including emergency, music to selected zones can

be played, upto 255 messages can be stored in the

internal 16MB flash ROM, individual BGM volume

control for each zone, Digital pre-recorded

messages can be merged, full system supervision,

Complete as required (Similar to Bosch Cat. No.

LBB 1990 or equivalent)

Nos. 1 195336.19 195336.192

8.12


Ceiling/wall mounted 6 watt speaker with line

matching transformer as per specification,

Complete as required (Similar to Bosch LBD

0606).

Nos. 137 1019.22 139632.592

8.13 SITC of 12 W Box Speaker Nos. 5 2134.69 10673.45



8.14 SITC of Plena Booster Amplifier 480 W Nos. 4 42435 169740

8.15SITC of CALL/PAGING Station Set of 6 zone

paging controller with set of 4 keypadNos. 1 126787.5 126787.5

8.16 SITC of 240 RMS mixer amplifier Nos. 1 25228.13 25228.13

8.17 SITC of 6 zone router Nos. 4 109968.75 439875

8.18 SITC of 15 U Rack with Accessories Nos. 1 20053.13 20053.13

8.19 SITC of XLR Connectors for paging stations Nos. 8 582.19 4657.52

8.20

Supplying and fixing of following sizes of steel

conduit along with the accessories in

surface/recess including painting in case of surface

conduit or cutting the Wall and making good the

same in case of recessed conduit as required.

1.20.2 25 mm dia Rmt 4800 147 705600

8.21

Supplying, Laying and fixing following sizes PVC

insulated / PVC Sheathed XLPE ISI marked

unarmoured copper conductor cable of 1.1 KV

grade on surface of Wall/Ceiling as reqd

a) 2 x 1.5 sqmm Rmt 3500 77.0075 269526.25

8.22

Supply and Laying 2 core 24/.2 mm PVC insulated

twisted copper conductor wires in existing conduit/

trunking as required.

Rmt 2500 58.8881 147220.25

8.23

Supply of Glow Type EXIT Sign Board photo

luminescent of size 300 mm x 250 mm x 1.5 mm

rigid sheet signage containing Zink Sulphate as

bare chemical class – 1 material PSPA fixed on 3

mm acrylic sheet on both side showing marking

(running man, Arrow and Exit) and hanged with the

ceiling with chain and fastener including cost of

labour & material required to complete the job in all

respect up to the entire satisfaction of Engineer-in-

Charge of work.

Nos. 43 2772.27 119207.524

Total carried over to summary ₹ 4808206.7

SUBHEAD - IX . CCTV SYSTEM

9.01

SITC of 1/3" Super HAD CCD Colour Dome Fixed

Camera 650TVL, 0.1 Lux, 3.6/4/6/8 mm DC12V, -

10 deg. C to 50 deg.C, Auto White Balance

(AWB), Back Light Compensation (BLC), 2D DNR,

OSD, suitable for indoor application, 3 Years

Warranty, UL Listed, Inclusive of Taxes .

Nos

58 5977.7 346706.6

9.02

SITC of 1/3" Super HAD CCD Colour Dome

Varifocal Camera 650TVL, 0.0001 Lux, 2.8-11 mm

varifocal, DC12V, -10 deg. C to 50 deg.C, Auto

IRIS, Automatic Gain Control (AGC), Auto White

Balance (AWB), Back Light Compensation (BLC),

2D + 3D DNR, suitable for indoor application, 3

Years Warranty, UL Listed, Inclusive of Taxes .

Nos

1 9462.2 9462.2



9.03

SITC of 1/3” Super HAD IR Dome Fixed Camera ,

650 TVL, 0.5 LUX/F2.0 (0 Lux IR On), AWB, 20

meter IR, DC12V -10 deg. C to 50 deg.C, Auto

White Balance (AWB), Back Light Compensation

(BLC),2D DNR, IP 66, 3 Years Warranty, UL Listed

, Inclusive of Taxes. Nos

5 8068.4 40342

9.04

SITC of 1/4" CCD,High Speed Dome PTZ Camera,

6000TVL, 0.003 lux; 0.000001lux(B/W), 37x Optical

Zoom, Automatic Gain Control (AGC), IR Cut Filter,

Back Light Compensation (BLC), Automatic White

Balance (AWB), Auto IRIS, 360 Degree endless

Pan Travel, 0 Degree to 180 degree tilt, 3D DNR,

WDR, ICR D/N, 256 presets, 3.5 - 129.5 mm lens

for outdoor application, Auto Tracking, 3 Years

Warranty, UL Listed , Inclusive of Taxes.

Nos

1 91114.5 91114.5

11

9.05SITC of 16-Channel NVR(16Ch@1080P NVR, 2

HDDs, 1x1000M Port, 16 POE Ports, PAL) Nos7 79927.875 559495.125

9.06 SITC of HDD Surveillance 4 TB Nos 12 17983.125 215797.5

9.07

SITC of Gigabit stackeable managed switch with 24-

port 10/100/1000. Model No: SG300-24PP (CISCO

Make) Nos

2 63005.625 126011.25

9.08 SITC of Rack & Accessories :

a 9U rack including PDU (5 Socket) Nos 3 8797.5 26392.5

b 1U MS cable manager Nos 5 355.781 1778.905

c Mounting Hardware (10 pieces) Nos 10 258.75 2587.5

9.09 SITC of Pasive Component & Accessories :

a Cat-6 patch cord 1m Nos 95 420.469 39944.555

b Cat-6 Patch panel Nos 4 5821.88 23287.52

c RJ-45 connector Nos 1 2328.75 2328.75

9.10 22" TFT Colour Monitor as per specifications. Nos 17 8738.65 148557.05

9.11Supply and Surface Laying of RG11 Co-axial Video

cable in PVC conduit. Mtrs1950 81.0175 157984.125

9.12

Supply and Laying of 2 Core x 1.0 sq.mm

unarmoured PVC Sheathed, AneAled Tinned

Copper, Power Cable. IN pvc conduit Mtrs

1560 75.21 117327.6

9.13Power Supply for Cameras 12 V DC ( Procure

Locally) Nos64 754.975 48318.4

9.14Power Supply for PTZ cameras 24 V AC (Procure

Locally) Nos1 1452 1452

9.15Supply and Surface laying of 2 Core 1 sqmm

flexiable shielded data cable in PVC conduit. Mtrs300 81.02 24306

Total carried over to summary ₹ 1983194

SUBHEAD - X . NURSE CALL SYSTEM



10.01 Supplying, fixing testing and commissioning of

modular nurses station LED type terminal monitor

with in built display & alarm, suitable for following

way complete with back up, batteries, battery

charger etc. as per technical specifications and as

required.

i) 30 Way Each 7 58995 412965

10.02

a)

Supplying, fixing testing and commissioning of call

push button (with cord), call reset, call indication

station for each bed complete as required.Each 184 3933 723672

10.02

b)

Toilet Pull Cord UnitEach 10 4301.7188 43017.1875

10.03 Supply and drawing 0.61, 3 pair PVC insulated

Cable in existing MS Conduit on recessed complete

as required

Metre 5820 86.0344 500720.208

10.04 1.20.2 Supplying and fixing of following sizes of steel

conduit along with accessories in surface/recess

including painting in case of surface conduit, or

cutting the wall and making good the same in case

of recessed conduit as required. 25 mm Dia

Metre 3492 147 513324

10.05 Supplying, fixing testing and commissioning of

LED's Indicators outside each ward Each 20 1536.3281 30726.5625


SUBHEAD - XI . Local Area Network (LAN)

SITC of Structured cabling for Data, wireless and

voice

11.01 Supplying and fixing following size/ modules, GI

box alongwith modular base & cover plate for

modular switches in recess etc. as required.

1.27.2 3 Module (100 mmX75 mm) for existing RJ 45 each 182 185 33670

11.02 Cat-6 components

a Cat-6 I/O (Data) No/s 200 226.4 45280

b Face Plate - (D) No/s 182 109.97 20014.54

c Cat-6 utp patch cord 1m No/s 160 200.53 32084.8

d Cat-6 utp patch cord 2m No/s 170 213.47 36289.9

e Cat-6 24-port patch panel No/s 14 6210 86940

11.03 Network Rack and accessories

a 42U 600x800 network rack with front glass and

back perforated doors, fan tray with four fans and

power strip

No/s 1 63135 63135

b PVC cable manager (1U) Horizontal No/s 10 355.78 3557.8

c Mounting Hardware (10 pieces) No/s 25 323.44 8086

11.04 Switching Component/s (hardware)

a Gigabit stackeable managed switch with 24-port

10/100/1000. Model No: SG500-28No/s 1 63005.63 63005.63

b Gigabit stackeable managed switch with 24-port

10/100/1000. Model No: SG300-24No/s 5 32990.63 164953.15



11.05 1.53.1 Supplying and drawing of UTP 4 pair CAT 6 LAN

Cable in the existing surface/ recessed steel/ PVC

conduit as required.

mtr. 12200 34 414800


SUBHEAD - XII . EPABX

Supply, Installation, Testing & commisioning of

following :

12.01 Progility IP PBX “HP 256 T+” System

Supports 14 universal slots and 2 dedicated slots

for PRI/VoIP

Progility HP 256 T+

Expandable System support up to 224 TDM & 256

IP Users

Supports Standalone as well as Networked

scenarios.

19” Rack mountable

Supports Video Telephony on IP

Supported interfaces:-

Analog Extensions

Digital Extensions

SIP Extensions (Native SIP)

Analog Trunks

ISDN Trunks

VoIP Trunks (For networking)

Supports 230V AC power supply as well as

provision for -48 V DC

battery back up

Support In-Skin Voicemail with e-mail integration #

Support In-Skin Voice recording #

Support Redundancy for control card (No

disconnection of calls in case of failover)

Addition of cards

Inbuilt Music on Hold,

08 Party adhoc Conference

CLIP facility for all offered extension & trunks

Call barring (scheduled/Manual based)

Busy call back,

Boss/Secretary feature

Night Service/ Day Service

Analog Extension with CLIP : 104 Nos

Digital Extension : 08 Nos

Analog Trunk Lines : 08 Nos

PRI Line 30 Chs : 01 Nos

In-built IVR for incoming PSTN (Analog & PRI) lines

Supports multi-level tree structures

Simultaneous 32 calls can be handled

12.02 Operator Consol (8150 with DSS 64) (price

inclusive)

Display : 2 Lines Backlit, 16*2 Characters, Key : 16

Fixed

function Keys, Jog Dial, 30 DSS Key, 100 No. of

phone book

entries, Ring Tones : 8 difference ring tones,

Volume



adjustment : 4 Level, Acoustics:- Hands free

talking, DSS 64

Key Module, Support for DSS 64 Key module : Yes,

Name

display of calling party : No

(item 6.01+6.02)No/s 1 475582.5 475582.5

12.03 Digital Phone 8150 No/s 3 8849.25 26547.75

Display : 2 Lines Backlit, 16*2 Characters,

Key : 16 Fixed function Keys, Jog Dial, 30 DSS

Key,

100 No. of phone book entries,

Ring Tones : 8 difference ring tones,

Volume adjustment : 4 Level

Acoustics:- Hands free talking

Support for DSS 64 Key module : Yes

Name display of calling party : No

12.04 Analog Clip Phone- Progility P100 No/s 170 1164.38 197944.6

12.05 Bittel Uranus Lobby Phone (Fire Communication

Phone)No/s 20 3848.91 76978.2


EXTERNAL ELECTRIFICATION

SUBHEAD - XIII HT - 33 kv TWO POLE

STRUCTURE

13.01 N.S.R.

Supplying of swaged tublear steel poles ( SP-410-

72-13 Mtr) of standerd sizes in cement concrete

foundations 1:3:6 (1 cement :3 coarse sand : 6

graded stone aggregate 20mm nominal size)

including excavation ,back filling,disposal of soil

and aligning keeping the pole in vertical position

with bottom of pole at 1.85mtr.below ground level

on 150mm thick base padding P.C.C. (Pole is to

be used for making D.P. structure for H.T.

tapping point) etc. all as required.(as per

requirement of .S.E.B.)

Each 2 25609.78 51219.56

13.02 a) N.S.R. 33KV Bus Isolator set 1 40145.06 40145.06

13.02 b) N.S.R. 33KV Line Isolator set 1 46374.47 46374.47

13.03 11.14

Erection of metallic pole of 13 Mtr length in cement



foundation including excavation and refilling etc. as

required.

each 2 4688 9376

13.04 11.16

Providing and making steel pole collar with cement

concrete (1 cement : 3 coarse sand : 6 stone

aggregate 20 mm) of specified size and shape

including form work, plastering if required, curing

etc. as required. (volume of pole/ pipe not to be

deducted

CUM 0.32 4693 1501.76



13.05 13.21

Supplying of two lengths of channel iron 100 mm X

50 mm X 6 mm (9.56 kg per meter) double pole

cross arm for three wire 33 kV over head line

conductors complete with through bolts and nuts for

clamping to the poles, 50 mm X 6 mm M.S. flats

welded on one side to the channel iron and with

bolts and nuts on the other side for tying the cross

arms together, including drilling holes for insulator

pins/ fittings, bolts, nuts, washers etc. and painting

with primer and finish paint as required.

set 4 4013 16052

13.06 13.22

Supplying and erection of a set of cross bracing

frame work for 33 kV over head line double pole

structure having four members fabricated out of 65

mm X 65 mm X 6 mm angle iron to form a

rectangle of minimum size 2400 mm width X 2800

mm height complete with 50 mm X 6mm M.S. flat

iron clamps, bolts and nuts including drilling holes

for insulator pins, bolts, nuts, washers etc. and

painting with primer and finish paint as required.

set 2 6027 12054

13.07 13.23

Supplying and erection of 33 kV pin insulator

complete with large steel head G.I. pin, nuts,

washers etc. as required.

set 3 728 2184

13.08 13.24

Supplying and erection of a set of three 11 kV disc

insulator for 33 kV over head lines with galvanised

insulator fittings, ball and socket type and complete

with galvanised strain clamps, bolts, nuts, washers

etc. as required.

set 3 2635 7905

13.09 13.25

Supplying and erection of single piece nonlinear

resistor type lightning arrestor suitable for 3 wire,

33 kV overhead lines with rated voltage 30 kV (rms)

with a nominal discharge current rating of 10 kA

(station class) and complete with galvanised

clamping arrangement, G.I. bolts, nuts, washers

etc. as required.

set 1 18575 18575

13.10 13.14

Supplying and erection of galvanised stay set for 33

kV over head lines complete with 19/ 20 mm dia X

1.8 meter long stay rod, anchor plate of size 45 cm

X 45 cm X 7.5 mm thick, thimble, stay clamps, turn

buckle (20 mm X 600 mm), 7/ 4.00 mm dia G.I. stay

wire and 33 kV strain insulator etc. in cement




required.

set 2 3821 7642

13.11 N.S,R.

Supplying and drawing standard steel

reinforcement aluminum conductor conforming to

IS 398/ 1961 of approved make , stringing on HT

poles structures including making of complete with

binding jointing, jumpers tearing of connections

atexisting HV insulators with suitable GI hardware

etc. as required.

a) ACSR 3 of 6/7 dog conductor i.e. 6/4.72

aluminum and 7/1.57mm steel conductor.kg 60 75 4500




SUBHEAD XIV :- 33KV SYSTEM

33 KV, H.T. PANEL:( 1 INCOMERS, 1 & 2 NOS

OUTGOINGS)

33 KV Main Panel

14.01 N.S,R.

Supplying, installation, testing & commissioning of

indoor type floor mounted extendable type, metal

clad, totally enclosed, 3 Panel 33 KV VCB board (1-

Incoming and 2- nos outgoing) single break, trip

free, motorised spring charged wth electrical

closing arrangement with horizontal drawout and

horizontal isolation type VCB with mechanical

ON/OFF indicator and trip device,4 NO + 4 NC

auxilliary contact complete with self contained, fully

interlocked, rack in and rack out mechanism as per

IS 13118, as amended up to date and additional

specifications, with air insulated encapsulated

copper bus bars of 630 Amps capacity suitable for

use on 33 KV, 3 Phase, 50 Hz AC supply and short

circuit withstand capacity of 25 KA for three

seconds, and bottom entry gland plate suitable for

3 x 240 sqmm. 33 KV XLPE cable.(But without cost

of end termination)

(A) Incoming - 1 No.(Comprising of)

a) 1 No. - 33 KV, 630 Amp VCB with 33 KV / 110V

PT of 100 VA burden and Accuracy Class 1, Shunt

trip Coil suitable for operation on 48 Volt DC.

b) 1 Set - Dual core CTs 100/5/5 A of 15 VA burden

and accuracy Class- 1 for metering and class 5P10

for protection.

c) 1 Set- 0-38 KV Digital Voltmeter with selector

switch and fuses

d) 1No- Local/ Remote selector switch

e) 1No - Trip/ Neutral/ Close switch

f) 1 Set- ON/OFF, Spring Charged LED indication

lamp.

g) 1 No. - Microprocessor based IDMT relay with 3

O/L, 1 E/F element

h) 1 No- Master trip relay

i) 1 No- PT fuse failure relay.

j) 1 No- Trip Circuit supervision relay.

k) Gland plate suitable for 3C x 120 sqmm 33 KV

grade XLPE cable.

(B) Outgoing - 2Nos (each comprising of)

a) 1 No. - 33 KV, 630 Amp VCB with Shunt trip Coil

suitable for operation on 48 Volt DC.

b) 1 Set - Dual core CTs 50/5/5 A of 15 VA burden

and accuracy Class- 1 for metering and class 5P10

for protection.

c) 1No- Local/ Remote selector switch

d) 1No - Trip/ Neutral/ Close switch

e) 1 Set- ON/OFF, Spring Charged LED indication

lamp.

f) 1 No. - Microprocessor based IDMT relay with 3

O/L, 1 E/F element

g) 1 No- Master trip relay

h) 3 Nos- 3 element Aux relay for Buchhotz Alarm &

Trip, Oil Temp Alarm, Winding Temp Alarm, PRV

Trip, MOG Alarm.



i) 1 No- Trip Circuit Supervision Relay.

j) Gland plate suitable for 3c x120 sqmm 33 KV

grade XLPE cable.

(C ) Remote operation panel

Remote operation panel fabricated with 2mm thick

CRCA sheet having three sections ( 1-Incomer, 2-

Out going) provided with

(a) Incoming section: 1 No (comprising of)

i) 1 Set- 0-38 KV Digital Voltmeter with selector

switch and fuses

ii) 1 Set. - 0-100A Digital Ammeter with selector

switch.

iii) 1 No. - Digital multi function meter suitable for

reading Voltage, Current, Power factor, KVA, KW,

KVAR, KWHr, KVAHr

iv) Trip/Neutral/close switch.

v) ON/OFF/ Spring charge LED type Indicating

lamp

vi) Test terminal block

vii) 1 No- 6 Window Annunciation Facia with test,

accept and reset button.

viii) 1 Lot- Instrument Fuses

(b) Outgoing section- 3 nos (Each comprising

of)

i) 1 Set. - 0-100A Digital Ammeter with selector

switch.

ii) Trip/Neutral/close switch.

iii) ON/OFF/ Spring charge Indicating lamp

iv) Test terminal block

v) 1 No- 12 Window Annunciation Facia with test,

accept and reset button.

vi) 1 Lot- Instrument Fuses

Control Supply Voltage:

a) Motor operation, Heater, Panel Illumination Light

: 230V AC

N.S,R.b) Shunt Trip, Closing, Indication & Annunciation

: 48 V DCset 1 2648808 2648808.01

14.02 N.S,R. 48V, DC Battery Bank (200AH).

Suppy, Installation, Testng and Commissioing of

Lead Acid Battery Bank Type PLANTE having

48Volt cell (24 Nos.) along with connector, link,

insulator and Steel/Wooden Battery shelve. The

following accessories are to be supplied with the

Battery Bank.

a) 2 Set - Rubber Glaves

b) 2 Nos. - 2 Volt measuring Voltmeter

c) 2 Nos. - Hygro meter

d) 2 Sets - Rubber Appron

e) Lot - 40 Lt₹of spare electrolyte in container Set 1 216603 216603

14.03 N.S,R. 48V, DC Battery Charger and DCDB.

Suppy, Installation, Testng and Commissioing of

48V DC Battery charger for the above 48V DC

plante type battery bank,Transformer for Boost and

trickle charging system with indicating, metering

and necessary protective instrument/relays as per

technical specification.

a) 1 No. Ampere - Hour meter has to be included.

b) Battery charger should have a DC Distribution

Board as an integral / separate DB consisting of the

following equipments.



c) 1 - 125A rated DC MCCB as incomer

d) 8 - 20A DP MCB (DC) as outgoing feeder

e) 1 Set - 125A rated DC Busbar (Copper) Set 1 190469 190469

(Transformer)

14.04 1000 KVA transformer with oil soak pit

DSR-14

CEVIL_

19.32.1

Making soak pit 2.5 m diameter 3.0 metre deep

with 45 x 45 cm dry brick honey comb shaft with

bricks and S.W. drain pipe 100 mm diameter, 1.8 m

long complete as per standard design. With

common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 (The pit shall be adequate to

hold 1000 lt oil).

Jobs 1 18309.5 18309.5

14.05 N.S,R.

Supplying installation testing and commissioning of

1000 KVA 33/ 0.433KV, 3 Phase, 50Hz, Dyn l1,

oilcooled ONAN type, copper wound transformer

with ON load tap changing arrangement on HV side

from + 5% to -15% in steps 1.25% along with

remote control panel having cable end boxes on

both sides suitable for 3C x 120 Sq.mm. XLPE

cable on 33KV side and Bus duct on 433V side

complete with buchlotz relay, oil and winding

temperature indicator and alarm contact, PRV,

MOG with all accessories i/c first filling of filtered

dehydrated oil and confirming to IS 1180 ( STAR-I )

including buchholz relay, oil & winding temprature

indicator, marshalling box, interconnections with HT

panel, RTCC panel with Receiving & installation of

copper control cable of size 2.5 Sqmm PVC

armoured Copper cable as required as per

specification. and Including Heat Run Tested as

for real time application.& as per specification

attached complete in all respects on outdoor plinth

as required (to be installed oudoor).

( 1 WORKING +1 STANDBY)

Nos 2 2292813 4585626

14.06 NSR

Supply of the following sizes of 33 KV XLPE AL

Earthed armoured cable in cable trenches or in

ducts over a bed of sand and covering with bricks

as per specifications including excavation of

trenches and back filling complete as required

33 KV, 3C x 120 Sq. mm XLPE Aluminium cablemtr 30 996.24 29887.2

14.07

Laying of one number XLPE power cable of 33 kV

grade of following size direct in ground including

excavation, sand cushioning, protective covering

and refilling the trench etc. as required.

8.5.1 Upto 120 sq. mm meter 30 275 8250

HV CABLE JOINTING & END TERMINATION

14.08

Supplying and making indoor cable end termination

with heat shrinkable jointing kit complete with all

accessories including lugs suitable for following

size of 3 core, XLPE aluminium conductor cable of

33 kV grade as required.

10.7.2 120 sq. mm each 4 14283 57132



14.09 10.80

Supplying and making outdoor cable end

termination with heat shrinkable jointing kit

complete with all accessories including lugs

suitable for following size of 3 core, XLPE

aluminium conductor cable of 33 kV grade as

required.

10.8.2 120 sq. mm each 1 18777 18777


SUBHEAD-XV : SAFETY EQUIPMENT & CABLE

TRAY

15.01 Providing & fixing of SAFETY EQUIPMENT

a) 2.22

H.T. (33 KV) DANGER NOTICE PLATE of

250mmx200mm size made of mild steel at least

2mm thick and vitreous enameled white on both

sides and with inscription in signal red colour on

front side as required

set 6 163 978

b) 2.21

Providing & fixing M.V. (440 V) Danger notice

plate of 200mmx150mm made of mild steel at least

2mm thick and vitreous enameled white on both

sides and with inscription in signal red colour on

front side as required.

each 10 149 1490

15.02

Supply & erection of the following Safety and

testing equipment Including miscellaneous items

like clamps, nuts & bolts ,rawl plug etc at suitable

places in the substation building as required

a)

G.I.buckets of 3 nos 5 liters capacity duly painted

white inside and red oxide paint out side and

written 'FIRE' with white paint & filled with dry sand

and mounted on M.S. angle iron bracket of size

50x50x6mm thick and 1200 mm long including

grouting in wall /floor etc. as required.

set 5 2600 13000

b)

First aid box as approved by St.John Ambulance

Brigade/Indian Red Cross Society and confirming

to IS 2217/ 1963.

each 2 410 820

c)

Shock Treatment chart duly glazed mounted on

Aluminum Frame with sheet glass as

required.

each 2 509 1018

d)

Providing and laying ISI 5424 marked 20 mm

thick nonskid type insulating Rubber mat to

withstand 11 KV dielectric strength as required

sqm 5 2925 14625

e)

Providing and laying ISI 5424 marked 12 mm

thick nonskid type insulating Rubber mat to

withstand 1.1 KV dielectric strength as required

sqm 8 1550 12400

f)Supplying rubber gloves 11 KV grade as per

I.S. code.Pair 2 350 700

15.03

Providing & fixing of M.S. angle iron with fixing

materials and painting for cable racks in trenches/

on walls etc .as required.

Kg 100 65 6500



15.04

Providing and fixing of M.S.slotted Angle 'C'

channel/Ladder type rack/Tray i/c fixing materials

grouted in wall or hanging with M.S. rod hanger

from ceiling including 2 coat synthetic enamel

painting over 1 coat of red oxide primer etc. as

required.-

Kg 100 65 6500

15.05

Supplying and installing following size of perforated

painted with powder coating M.S. cable trays with

perforation not more than17.5%, in convenient

sections, joined with connectors,suspended from

the ceiling with M.S. suspenders including bolts &

nuts, painting suspenders etc. as required.

a) 4.1.1100 mm width x 50 mm depth x 2 mm thickness

mtr 200 348 69600

b) 4.1.2150 mm width x 50 mm depth x 1.6 mm thickness

mtr 250 393 98250

c) 4.1.4 300 mm width x 50 mm depth x 1.6 mm thickness

mtr 2000 526 1052000

d) 4.1.6 450 mm width x 50 mm depth x 2.0 mm thickness

mtr 50 782 39100

e) 4.1.7 600 mm width x 50 mm depth x 2.0 mm thickness

mtr 100 950 95000


SUBHEAD XVI : MEDIUM VOLTAGE PANEL BOARD

NOTE: ALL ACBs ARE REQUIRED WITH SAFETY

SHUTTER, UNDER VOLTAGE RELEASE /

SHUNT TRIP

General Note for all Panels

Note 1

The Panels/ Switch-boards shall be fabricated out

of (load bearing member of 2mm and non load

bearing member 1.6 mm thick) CRCA sheet steel,

Compartmentised design, modular construction

with Form 4b separation for Main Panels & 3b for

remaining, Mounting Plates and Internal Partition

shall be made of 1.6/2.0mm Aluzinc sheet for better

heat dessipation clear space of 300mm or as

approved shall be left at the bottom.The operating

handle of the topmost switch shall not be higher

than 1800mm from the finished floor and maximum

height of panels shall not more than 2400mm.The

Panel shall be Powder coated to paint of desired

shadend in an approved manner.

Note 2

Panel Manufacturer must have an established track

record in Design, Manufacturing and Supply of IEC

61439 certified Assemblies

Note 3 Undervoltage Relay (27)

Note 4 Reverse power RELAY (32)

Note 5 Inverse Definite minimum time overcurrent relay

Note 6 Overvoltage Relay (59)

Note 7Bucholz protection (only transformer switch ) (63)

Note 8 Emergency stop on each panel



Note 9

All incomers and Bus coupler panel door should be

different colour coded for identification and mimic

diagram in front of panel should be marks by

reflector paints

Note 10

All ACB terminals shall have vertical-vertical

configuration for termination of incoming & outgoing

bus links. All MCCB’s up to 630A shall be provided

with rear stud type terminations.

Note 11Space heater, Thermostat, On/Off switch, LED

Lamp , Door operated switch.

16.01 N.S.R.

Supply, Erection, Testing and commissioning of

Indoor type ( IP 54 Protection ) cubicle pattern

LT Switch-Board with a rupturing capacity of 50

KA at 415 V for 1 sec or as called for in individual

items, openable in front and back suitable for 3

phase, 4 wire, 50Hz AC supply at an ambient

temperature of 45 C. The cubicle should be

weather proof, dust proof vermin proof, well

ventilated and enclosure protection shall be IP-54

as per IEC 61439, fabricated out of (load bearing

member of 2mm and non load bearing member 1.6

mm thick) CRCA sheet steel in Compartmentised

design, modular construction with Form 4b

separation for Main Panels & 3b for remaining,

Mounting Plates and all Internal Partition shall be

made of 1.6/2.0mm Aluzinc sheet for better heat

dessipation. The cubicle should be front operated,

floor mounted, free standing with compartments in

tier formation, extensible on both sides.The panel

to be provided with PVC Sleeved 4 pole Electrolytic

Al .Maximum Current density for the bus bars shall

meet temp rise condition as per IEC61439. Bus Bar

and PVC insulated solid interconnections and also

provided with 50x6mm. horizontal AL Earth Bus

Bars in each section.(as per drawing- enclosed-

TRF INCOMER:-

2 Nos 1600A FP EDO ACB 50kA With

Microprocessor Based Release (O/C,S/C,E/F)

Protection & S/T(from 1000 KVA transformer

each)

2 Nos Under Voltage Relay (27)

2 Nos Over Voltage Relay (59)

2 Nos IDMT Overcurrent Relay

2 Nos Multifinction Meter With RS-485 port

6 Nos C.T's 1000/5Amp , CL 1.0, 15VA

8 Nos Aux. Contactor

2 Nos Breaker Control Switch

2 Nos A/M Selector switch

2 sets Phase Indicating LED with MCB

2 sets ON,OFF,TRIP Indicating LED

10 Nos Control SP MCB

1 no emergency stop push buttan switch (to control

whole panel)

INTERLOCKING:- (refer SLD)

Electrical & Mechanical Interlocking Between

TRANSFORMER Incomers & BUSCOUPLER

BUSCOUPLER

1 Nos. 1600 A FP EDO ACB 50kA Without release

2 set of ON/OFF indication light

2 No. Breaker Control Switch



BUSBAR :-

2000 Amps 4 pole 50 kA aluminum conductor (

CD 0.8A /sq.mm. ) bus bar (PVC sleeve Heat-

shrinkable busbar insulation) supported by DMC /

FRP insulato₹(MAIN BUSBAR)

OUTGOING

1-All MCCB should be Adjustable thermal magnetic

Release ,Ics=100%Icu with Rotary Handle. Fault

Level minimum 25KA

1-ON Indication Light for all Outgoings. With MCB

L.H.S.

1 No. 500Amps TPN ,MCCB adjustable with rotary

handle for 206 KVAr capacitor panel no-1)

1 Nos 1000A FP EDO ACB 50kA With


Protection & S/T(for Essential panel )

3 Nos. 200Amps FP ,MCCB adjustable with rotary

handle for Ground Floor P.DB, First Floor P.DB,

Spare


handle for Second Floor P.DB, Spare

2 No. 100Amps FP ,MCCB adjustable with rotary

handle for Spare


handle for Ground Floor P.DB, First Floor P.DB,

Fourth Floor P.DB, Spare


handle for Second Floor P.DB, Third Floor

P.DB, Spare

R.H.S.

1 No.630A FP EDO ACB 50kA With Thermal

Magnetic Based Release (O/C,S/C,E/F) Protection

& S/T(for Essential panel )


handle for 130KVAR, Spare


handle Fourth Floor P.DB


handle for Third Floor P.DB

1Nos. 100Amps FP ,MCCB adjustable with rotary

handle for Spare


handle for Spare



2 nos. of Type 1/Class I surge protection:

According to IEC 61643-1, IEC 62305, IEC 61312-

1; Type 1/Class I encapsulated spark gap

technology surge protection device at the main

incomer LT panel after the breaker in parallel to the

load with the following technical paramete₹03

numbers of 50 KA (10/350 micro sec) to be

connected between each phase & neutral (R,Y,B &

N) and 01 number of 100 KA (10/350 micro sec) to

be connected between neutral & earth with a

voltage protection level of less than 1300 volts, with

the response time of 100 nano seconds. Back-up

tripping provision of 63A MCB in series (in parallel

to the load) with the spd (to be connected before

the spd) to break incase of any abnormal failure of

the spd.

Miscellaneous items

10 nos door switch

10 nos illumination lights with 6 A,10kA MCB

ILLUMINATION LED WITH HOLDER & DOOR

SWITCH

4 nos 6" dia exhaust fan with thermostate &

suitable canopy

Internal illumination in Cable alleys with Door

operated switch.set 1 3611317.4 3611317.4

16.02 N.S.R.



















tier formation, extensible on both sides.The panel

to be provided with PVC Sleeved 4 pole Electrolytic

Al .Maximum Current density for the bus bars shall

be meet temp rise condition as per IEC61439. Bus

Bar and PVC insulated solid interconnections and

also provided with 50x6mm. horizontal AL Earth

Bus Bars in each section.(as per drawing-

INCOMER:-

1 No630A FP EDO ACB 50kA With Microprocessor

Based Release (O/C,S/C,E/F) Protection &

S/T(from Main Panel)

1 No 1000A FP EDO ACB 50kA With


Protection & S/T(from Main Panel)

2 Nos Under Voltage Relay (27)

2 Nos Over Voltage Relay (59)


3 Nos C.T's 630/5Amp , CL 1.0, 15VA



3 Nos C.T's 1000/5Amp , CL 1.0, 15VA

4 Nos Aux. Contactor

2 Nos Breaker Control Switch


2 sets Phase Indicating LED with MCB

2 sets ON,OFF,TRIP Indicating LED


1 no emergency stop push buttan switch (to control

whole panel)

DG Section - Incomer (500KVA)

1 No. 800A FP EDO ACB 50kA With


Protection & S/T (from 500KVA DG)

1 No. Reverse Power Relay

1 No. Under Voltage Relay (27)

1 No. Over Voltage Relay (59)

1 No. Multifinction Meter With RS-485 port

3 Nos C.T's 800/5Amp , CL 1.0, 15VA


1 No. 8 Window Annunciator

1 No. Hooter


1 set Phase Indicating LED with MCB

1 set ON,OFF,TRIP Indicating LED


DG Section - Incomer (250KVA)



Protection & S/T(from 250KVA DG)

1 No. Reverse Power Relay

1 No. Under Voltage Relay (27)

1 No. Over Voltage Relay (59)

1 No. Multifinction Meter With RS-485 port

3 Nos C.T's 600/5Amp , CL 1.0, 15VA


1 No. 8 Window Annunciator

1 No. Hooter


1 set Phase Indicating LED

1 set ON,OFF,TRIP Indicating LED


INTERLOCKING:- (refer SLD)

Electrical & Mechanical Interlocking Between

Incomer from Main Panels & DG Incomers &

BUSCOUPLER

BUSCOUPLER


Microprocessor Based Release without proection

1 set of ON/OFF indication light


BUSBAR :-

1250 Amps 4 pole 50 kA aluminum conductor (

CD 0.8A /sq.mm. ) bus bar (PVC sleeve Heat-

shrinkable busbar insulation) supported by DMC /

FRP insulato₹(MAIN BUSBAR)

OUTGOING



1-All MCCB should be Adjustable thermal magnetic

Release ,Ics=100%Icu with Rotary Handle. Fault

Level minimum 25KA

1-ON Indication Light for all Outgoings.

L.H.S.

1 No. 800A FP EDO ACB 50kA With Thermal

Magnetic Based Release (O/C,S/C,E/F) Protection

& S/T(for AC Panel)


handle for UPS Panel + CATH LAB


handle for CT SCAN, spare


handle for CSSD+MRI+GFL Medical panel+


handle for Ventilation Panel


handle for F FL Medical Panel

1 No 125Amps FP ,MCCB adjustable with rotary

handle for Kitchen Panel


handle for Spare, Medical Gas Panel

R.H.S.


handle for UPS Panel


handle for Rising Main


handle for Fire Panel,


handle for Pump Panel , Solar


handle for Spare+ LAUNDRY

3 Nos 63Amps FP ,MCB adjustable with rotary

handle for Lift-1&2,Lift-3&4, Spare

1 Nos 40Amps FP ,MCCB adjustable with rotary

handle for External Lighting

2 nos. of Type 1/Class I surge protection:

According to IEC 61643-1, IEC 62305, IEC 61312-

1; Type 1/Class I encapsulated spark gap

technology surge protection device at the main

incomer LT panel after the breaker in parallel to the

load with the following technical paramete₹03

numbers of 50 KA (10/350 micro sec) to be

connected between each phase & neutral (R,Y,B &

N) and 01 number of 100 KA (10/350 micro sec) to

be connected between neutral & earth with a

voltage protection level of less than 1300 volts, with

the response time of 100 nano seconds. Back-up

tripping provision of 63A MCB in series (in parallel

to the load) with the spd (to be connected before

the spd) to break incase of any abnormal failure of

the spd.

Battery Charger for each DG incomer

230 V, Single Phase, 50 HZ, AC operated Battery

Charger for DC supply to DG Batteries with Boost

and trickle charging facility and protection from over

charging the D.G. set starting battery and a DC DB

with required numbers of outgoing DP MCB's plus 2

Nos. of 15 AMP. DP MCB's as spare feeders.



Miscellaneous items

10 nos door switch

10 nos illumination lights with 6 A,10kA MCB

ILLUMINATION LED WITH HOLDER & DOOR

SWITCH

4 nos 6" dia exhaust fan with thermostate &

suitable canopy

Internal illumination in Cable alleys with Door

operated switch.set 1 4270322.6 4270322.6

16.03 N.S.R.

















dessipation The cubicle should be front operated,

wall mounted,compartments in tier formation,

extensible on both sides.The panel to be provided

with PVC Sleeved 4 pole Electrolytic Al .Maximum

Current density for the bus bars shall be meet temp

rise condition as per IEC61439.Bus Bar and PVC

insulated solid interconnections and also provided

with 50x6mm. horizontal AL Earth Bus Bars in

each section.(as per drawing- enclosed)) -

INCOMER


handle from Main Panel

1 set of Phase Indication LED lights each backed

up with 6amp. MCB

1 no Digital VIF METER with class-1 accuracy

1 no- RMI-8 APFC Microprocessor based Relay

intelligent type relay setting 0.8 to 0.98 power

factor) for capacitor bank .built in PF meter

suitable contactor for above

3 nos CT's 500/5A class-1(15VA)

5 nos 6 amp SP MCB

1no 6 amp DP MCB

1 no Timer on delay (series 175) 220V AC

Auto / Manual selector switch (3P,2 way with OFF)

1 No Thermostat(30-80 degree)

1 No. Aux. Contactor 8NO+8NC (220V AC)

2 Nos. Aux. Contactor 4NO (220V AC)

2 nos Axial flow fan- 6" ( Heavy Duty)

OUTGOING

i)

7 sets of ON -OFF push buttons station red &

green with ON/OFF indicating lights for each

KVAR capacitor unit to indicate its position.(two

space only)



ii)7 nos Ammeter suitable for each capacitor Bank

with CT

iii) 1 nos 32 amp TP 10 KA MCB for 12.5 KVAr

iv) 1 nos 40 amp TP 10 KA MCB for 20 KVAr


v) 2 nos 100 amp TP 25 KA MCCB for 50 KVAr

vi)1 nos. Capacitor duty contactor suitable rating for

12.5kVAR Rating

vii)1 nos Capacitor duty contactor suitable rating for 20

kVAR Rating

viii)3 nos. Capacitor duty contactor suitable rating for

25kVAR Rating

ix)2 nos. Capacitor duty contactor suitable rating for

50kVAR Rating

x)1 nos. 12.5 KVAR, 415 V, MPP supper heavy duty

type capacitor bank with 7% detuned reactor

xi)1 nos. 20 KVAR, 415 V, MPP supper heavy duty


xii)3 nos. 25 KVAR, 415 V, MPP supper heavy duty


xiii)2 nos. 50 KVAR, 415 V, MPP supper heavy duty


Miscellaneous items

a 4nos door switch

b 4 nos illumination lights with 6 A,10kA MCB

cILLUMINATION LED WITH HOLDER & DOOR

SWITCH

d4 nos 6" dia exhaust fan with thermostate &

suitable canopy

eInternal illumination in Cable alleys with Door

operated switch.Each 1 630323 630323

16.04 N.S.R.


















wall mounted,compartments in tier formation,




rise condition. Bus Bar and PVC insulated solid

interconnections and also provided with 50x6mm.

horizontal AL Earth Bus Bars in each section.(as

per drawing- enclosed)) -Capacitor Panel-2 ., (as

INCOMER


handle from Main Panel

1 set of Phase Indication LED lights each backed

up with 6amp. MCB

1 no Digital VIF METER with class-1 accuracy



1 no- RMI-8 APFC Microprocessor based Relay

intelligent type relay setting 0.8 to 0.98 power

factor) for capacitor bank .built in PF meter

suitable contactor for above

3 nos CT's 300/5A class-1(15VA)

5 nos 6 amp SP MCB

1no 6 amp DP MCB

1 no Timer on delay (series 175) 220V AC

Auto / Manual selector switch (3P,2 way with OFF)

1 No Thermostat(30-80 degree)

1 No. Aux. Contactor 8NO+8NC (220V AC)

2 Nos. Aux. Contactor 4NO (220V AC)

2 nos Axial flow fan- 6" ( Heavy Duty)

OUTGOING

i)

6 sets of ON -OFF push buttons station red &

green with ON/OFF indicating lights for each

KVAR capacitor unit to indicate its position.(two

space only)

ii)6 nos Ammeter suitable for each capacitor Bank

with CT

1 nos 25 amp TP 10 KA MCB for 10 KVAr

iii) 2 nos 32 amp TP 10 KA MCB for 12.5 KVAr



v) 2 nos 100 amp TP 25 KA MCCB for 50 KVAr

vi)1 nos. Capacitor duty contactor suitable rating for

10kVAR Rating

vii)2 nos. Capacitor duty contactor suitable rating for

12.5kVAR Rating

viii)1 nos Capacitor duty contactor suitable rating for 20

kVAR Rating

ix)1 nos. Capacitor duty contactor suitable rating for

25kVAR Rating

x)1 nos. Capacitor duty contactor suitable rating for

50kVAR Rating

xi)1 nos. 10 KVAR, 415 V, MPP supper heavy duty


xii)2 nos. 12.5 KVAR, 415 V, MPP supper heavy duty


xiii)1 nos. 20 KVAR, 415 V, MPP supper heavy duty


xiv)1 nos. 25 KVAR, 415 V, MPP supper heavy duty


xv)1 nos. 50 KVAR, 415 V, MPP supper heavy duty


Miscellaneous items

a 4nos door switch

b 4 nos illumination lights with 6 A,10kA MCB

cILLUMINATION LED WITH HOLDER & DOOR

SWITCH

d4 nos 6" dia exhaust fan with thermostate &

suitable canopy

eInternal illumination in Cable alleys with Door

operated switch.Each 1 455029 455029



16.05 N.S.R.












mm thick) CRCA sheet steel in cubicle

compartmentised modular 4b construction for Main

Panels & 3b for remaining, Mounting Plates and all

Internal Partition shall be made of 1.6/2.0mm

Aluzinc sheet for better heat dessipation. The

cubicle should be front operated, wall

mounted,compartments in tier formation, extensible

on both sides.The panel to be provided with PVC

Sleeved 4 pole Electrolytic Al .Maximum Current

density for the bus bars shall be meet temp rise

condition as per IEC61439.Bus Bar and PVC



each section.(as per drawing- enclosed)) -LIFT

PANEL., (as per drawing enclosed))

INCOMER:-


handle


1 No. Digital Ammeter with Suitable CT's

1 No.Digital Voltmeter

3 Nos. Control MCB

BUSBAR :-

100 Amps 4 pole aluminum conductor ( CD 0.8A

/sq.mm. ) bus bar (PVC sleeve Heat-shrinkable

busbar insulation) supported by DMC / FRP

insulato₹(MAIN BUSBAR)

OUTGOING


handle for Lift-1, Lift-2 & Spare

3Nos 32 AMP TPN 10 ka MCB

2 nos 4 pole 300 ma RCBO each 2 177600 355200



16.06 N.S.R.


















floor mounted,compartments in tier formation,




rise condition as per IEC61439. Bus Bar and PVC



each section.(as per drawing- enclosed)) -UPS

INCOMER:-


handle from Essential Panel

2 sets of phase indication light with MCB

Note : Both shall be interlocked with each other

BUSBAR : 500A FP Aluminium Busbar


handle before By Pass Switch

3 Nos. 250A By Pass Switch


handle after By Pass Switch


3 sets ON/OFF indication light with MCB

9 Nos. CT- 250/5A,

10 Nos. Control MCB

BUSBAR :-

400 Amps 3pole & 600 Amps Neutral aluminum

conductor ( CD 0.8A /sq.mm. ) bus bar (PVC

sleeve Heat-shrinkable busbar insulation)

supported by DMC / FRP insulato₹(MAIN

BUSBAR)

OUTGOING

5 Nos. 100 Amps FP ,MCCB adjustable with rotary

handle for II-Fl UPS DB, III-Fl UPS DB, Cath LAB

DB, Dialysis DB, Spare

8 Nos 63 Amps FP ,MCCB adjustable with rotary

handle for IV-Fl UPS DB, OT-1 DB, OT-2 DB, OT-

3 DB, OT-4 DB, ICU UPS DB, NICU UPS DB,

Spare


handle for GF, 1F & spareeach 1 1129772 1129772

16.07 N.S.R.Supply, Erection, Testing and commissioning of




INCOMER:-





3 Nos. CT- 100/5A,

3 Nos. Control MCB

BUSBAR :-

200 Amps 4pole aluminum conductor ( CD 0.8A




OUTGOING

2 Nos. 18KW S/D Starter with 63A TPN MCCB,

ON/OFF/TRIP Indication with ON/OFF Push button

and Ammeter

2 Nos. 7.5KW S/D Starter with 25A TPN MCCB,

ON/OFF/TRIP Indication with ON/OFF Push button

and Ammeter

6 Nos. 63A TP Contactor with (18A-24A) thermal

overload relay

6 Nos. 25A TP Contactor with (8A-12A) thermal

overload relay

2 No 63 Amps TPN ,MCCB adjustable with rotary

handle for Spare

each 1 333375 333375

16.08 N.S.R.


















floor mounted,compartments in tier formation,




rise condition as per IEC61439. Bus Bar and PVC



each section.(as per drawing- enclosed)) -

INCOMER:-





3 Nos. CT- 250/5A,

3 Nos. Control MCB



BUSBAR :-





OUTGOING


handle for STEAM STERILIZER, SPARE


handle for AUTOCLAVE, SPARE


handle for 2 NO AUTOCLAVE, SPARE

1 No. 63Amps FP ,MCB adjustable with rotary

handle for SPARE

1 No. 32Amps FP ,MCB adjustable with rotary

handle for SPARE

2 Nos. 16 Amps FP ,MCB adjustable with rotary

handle for SPARE

2 Nos. 6 Amps FP ,MCB adjustable with rotary

handle for E.T.O. M/C-1 & 2each 1 300795 300795

16.09 N.S.R.









ventilated and enclosure protection shall be IP 55

with double door & canopy as per IEC 61439,

fabricated out of (load bearing member of 2mm and

non load bearing member 1.6 mm thick) CRCA

sheet steel in Compartmentised design, modular

construction with Form 4b separation for Main




cubicle should be front operated, floor





condition as per IEC61439. Bus Bar and PVC



INCOMER:-


handle from ESSENTIAL Panel



3 Nos. CT-250/5A,

3 Nos. Control MCB

BUSBAR :-





OUTGOING



3 Nos.100 Amps FP ,MCCB adjustable with rotary

handle for X-RAY-1+2 & SPARE

2 No. 32 Amps FP ,MCB 10kA for Physiotheraty

2 No. 10 Amps FP ,MCB 10kA for MINOR OT

3 No. 06 Amps FP ,MCB 10kA for ECG &SPAREeach 1 233341 233341

16.10 N.S.R.























condition as per IEC61439. Bus Bar and PVC



INCOMER:-


handle from ESSENTIAL Panel



3 Nos. CT- 160/5A,

3 Nos. Control MCB

BUSBAR :-





OUTGOING

3 No. 63 Amps FP ,MCB 10kA for Histopathology

bio-chemistry + spare

2 No.32 Amps FP ,MCB 10kA for blood bank

4 No. 16 Amps FP ,MCB 10kA f

8 No. 10 Amps FP ,MCB 10kA for Physiotheraty each 1 190993 190993



16.11 N.S.R.


Outdoor type ( IP 55 Protection ) cubicle pattern





















condition as per IEC61439.Bus Bar and PVC



INCOMER:-


handle from Housing Transformer



3 Nos. CT- 500/5A,

3 Nos. Control MCB

BUSBAR :-





OUTGOING

2 Nos.200 Amps FP ,MCCB adjustable with rotary

handle for 4 BHK, SPARE


handle for 2 BHK-1, 2 BHK-2, 3 BHK & SPARE

1 No. 63 Amps FP ,MCCB adjustable with rotary

handle for COMMONeach 1 362501 362501

Fabrication, supply, installation, testing and

commissionings of cubicle type out door type ,

floor mounted L.T. panel made out of 16mm thick

CRCA sheet including connection, inter-connection

alongwith 4 stsrip aluminium bus bar as per CP WD

specifications, ( Part IV - Sub-station) and IS: 8623

comprising of followings panel mounting

switchgears etc. as required., EXTERNAL

LIGHTING PANEL for Hospital



16.12 N.S.R.


commissionings of cubicle type out door type ,

floor mounted L.T. panel made out of 16mm thick


alongwith 4 stsrip aluminium bus bar as per CP WD

specifications, ( Part IV - Sub-station) and IS: 8623

comprising of followings panel mounting

switchgears etc. as required., EXTERNAL

LIGHTING PANEL for Hospital

(all MCCB are min. 25 KA fault rating )

A) Incoming

i) 1 Nos.40 Amps TPN MCCB adjustable Thermal

magnetic release with with rotary handle

ii) 100 amp 4 pole AL Busbar of 100 Amp

iii) 1 set of phase indication lights.

iv) 1 set of 3 phase contactor

iii) 1 set of Photo electric switch

iv) 3 nos of timer switch & contactor

v) 10 nos 32 amp DP MCB 10 kA

vi) 2 nos industrial plug & socket with 15 amp SP

MCB

vii) 1no 10 watt LED Lamp with holder & switch

,socket set 1 130183 130183

16.13 N.S.R.


indoor type cubicle pattern L T Switch-Board with a

rupturing capacity of 50 KA at 415 V or as called

for in individual items, openable in front and back

suitable for 3 phase, 4 wire, 50Hz AC supply at an

ambient temperature of 45 C. The cubicle should

be weather proof, dust proof vermin proof, well











tier formation, extensible on both sides. The panel

to be provided with PVC Sleeved TPN Electrolytic

Al. Bus Bar and PVC insulated solid


horizontal tinned copper Earth Bus Bars in each

section.(as per drawing no- EL-01- enclosed)) -

METER BOARD for TYPE-III

i) 1 Nos. 100 Amps TPN MCCB adjustable Thermal


ii) 1 set of phase indication lights.

iii) Bus bar :- 150 Amps TP&N 50 kA aluminum

conductor bus bar (BPTM type Heat-shrinkable


insulators.

OUTGOING

i) 8 Nos. 32 Amps , 10 ka,D Corve, DP MCB



ii) 8 Nos. space for Kwh meter along with locking

arrangementsset 1 104696.92 104696.92

16.14 N.S.R.
























METER BOARD for TYPE -II







insulators.

OUTGOING

i) 8 Nos.32 Amps , 10 ka,D Corve, DP MCB





16.15 N.S.R.
























METER BOARDfor TYPE -IV







insulators.

OUTGOING

i) 8 Nos. 63 Amps , 10 ka,D Corve, TPN MCB



16.16 N.S.R.


commissionings of cubicle type out door floor

mounted L.T. panel made out of 16mm thick


alongwith 4 stsrip aluminium bus bar as per IEC

61439, fabricated out of (load bearing member of

2mm and non load bearing member 1.6 mm thick)

CRCA sheet steel in Compartmentised design,

modular construction with Form 4b separation for

Main Panels & 3b for remaining, Mounting Plates

and all Internal Partition shall be made of

1.6/2.0mm Aluzinc sheet for better heat

dessipation. comprising of followings panel

mounting switchgears etc. as required., Utility

Panel-common area

from main ESSENTIAL PANEL

(all MCCB are min. 25 KA fault rating )

A) Incoming

i) 1 Nos.63 Amps FP ONLOAD CHANGEOVER

ii) 1 Nos.63 Amps TPN MCCB adjustable Thermal




PROTECTION INSTRUMENT

i) 1 set of phase indication lights.

ii) 1 sets of indication lights, phase, breaker ON-

OFF, , etc.

iii) 1 no 3 phase combined voltmeter, ammeter &

frequency meter , approved make with following

feature with suitable CT's

a) Latest Micro controller based technology,three

indipendent windows to view V,A & Hz per

phasesimultanously

b) Ultra bright LED Display for clear front & long

distance viewing

c)CT's ratio programable through front key ped

d) Four digit frequency meter with 0.01Hz

resolution

iv) Bus bar :- 100 Amps TP&N 50 kA aluminum



insulators.

1 no space for Dual source ( normal & DG supply )

3 phase Kwh meter board and space for its CT's

along with double locking arrangements

OUTGOING

i) 2 Nos. 63 Amps, 10 ka, TPN MCB

ii) 2 Nos. 32 Amps, 10 ka, TPN MCB

iii) 3 Nos. 16 Amps, 10 ka, SPN MCB

iv) 7 Nos. 6 Amps, 10 ka, SPN MCB

v)2 no 10 watt LED Lamp with holder & switch

,socket set 1

342879.4342879.4


SUBHEAD -XVII . CABLES AND TERMINATION

a) hospital

17.01Supply,Receiving of 1100V grade XLPE AA Cable

as per follows;

a) 4x6 sqmm mtr 200 125.75 25150

b) 4x10 sqmm mtr 200 158.59 31718

c) 3.5*35 sqmm mtr 100 273.16 27316

d) 3.5*50 sqmm mtr 400 352.11 140844

e) 3.5*70 sqmm mtr 750 477.86 358395

h) 3.5*95 sqmm mtr 200 594.53 118906

g) 3.5*120 sqmm mtr 350 741.94 259679

h) 3.5*150 sqmm mtr 1300 880.27 1144351

i) 3.5*185 sqmm mtr 650 1095.44 712036

j) 3.5*240 sqmm mtr 1250 1380.48 1725600

k 3.5*400 sqmm mtr 1150 2152.46 2475329

17.02

Laying and fixing of one number PVC insulated and

PVC sheathed / XLPE power cable of 1.1 KV grade

of following size on wall surface as required.

a) 7.7.1Upto 35 sq. mm (clamped with 1mm thick saddle)

mtr 100 25 2500

b) 7.7.2Above 35 sq. mm and upto 95 sq. mm (clamped

with 25x3mm MS flat clamp)mtr 500 72 36000

c) 7.7.3Above 95 sq. mm and upto 185 sq. mm (clamped

with 25/ 40x3mm MS flat clamp)mtr 450 84 37800



d) 7.7.4Above 185 sq. mm and upto 400 sq. mm

(clamped with 40x3mm MS flat clamp)mtr 450 120 54000

17.03

Laying of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of

following size in the existing masonry open duct as

required.

a) 7.6.1 Upto 35 sq. mm mtr 50 14 700

b) 7.6.2 Above 35 sq. mm and upto 95 sq. mm mtr 200 22 4400

c) 7.6.3 Above 95 sq. mm and upto 185 sq. mm mtr 600 31 18600

d) 7.6.4 Above 185 sq. mm and upto 400 sq. mm mtr 500 56 28000

17.04


sheathed / XLPE power cable of 1.1 kV grade of

following size direct in ground including excavation,

sand cushioning, protective covering and refilling

the trench etc. as required.

a) 7.1.1 Upto 35 sq. mm mtr 100 206 20600




17.05

Laying of one number additional PVC insulated

and PVC sheathed / XLPE power cable of 1.1 kV

grade of following size direct in ground in the same

trench in one tier horizontal formation including



a) 7.2.1 Upto 35 sq. mm mtr 100 141 14100




CABLE ENDS

17.06

Supplying and making end termination with double

brass compression gland and aluminium lugs for

following size of PVC insulated and PVC sheathed /

XLPE aluminium conductor cable of 1.1 KV grade

as required.

a) 9.1.32 4x6 sqmm set 10 203 2030

b) 9.1.32 4x10 sqmm set 12 203 2436

c) 9.1.21 3.5*35 sqmm set 2 282 564

d) 9.1.22 3.5*50 sqmm set 10 354 3540

e) 9.1.23 3.5*70 sqmm set 10 394 3940

h) 9.1.24 3.5*95 sqmm set 8 482 3856

g) 9.1.25 3.5*120 sqmm set 4 500 2000

h) 9.1.26 3.5*150 sqmm set 22 592 13024

i) 9.1.27 3.5*185 sqmm set 6 804 4824

j) 9.1.29 3.5*240 sqmm set 14 989 13846

k) 9.1.31 3.5*400 sqmm set 48 1389 66672

b) housing

17.07Supply,Receiving of 1100V grade XLPE AA Cable

as per follows;

a) 4x6 sqmm mtr 600 125.75 75450

b) 4x10 sqmm mtr 100 158.59 15859

c) 3.5x50 sqmm mtr 275 352.107 96829.425

d) 3.5x70 sqmm mtr 60 477.86 28671.6

e) 3.5x95 sqmm mtr 175 594.53 104042.75



17.08

Laying and fixing of one number PVC insulated and

PVC sheathed / XLPE power cable of 1.1 KV grade

of following size on wall surface as required.

a) 7.7.1Upto 35 sq. mm (clamped with 1mm thick saddle)

mtr 10 25 250

b) 7.7.2Above 35 sq. mm and upto 95 sq. mm (clamped

with 25x3mm MS flat clamp)mtr 10 72 720

17.09


sheathed / XLPE power cable of 1.1 kV grade of

following size direct in ground including excavation,

sand cushioning, protective covering and refilling

the trench etc. as required.

a) 7.1.1 Upto 35 sq. mm mtr 570 206 117420


17.10

Laying of one number additional PVC insulated

and PVC sheathed / XLPE power cable of 1.1 kV

grade of following size direct in ground in the same

trench in one tier horizontal formation including



a) 7.2.1 Upto 35 sq. mm mtr 20 141 2820


CABLE ENDS

17.11

Supplying and making end termination with double

brass compression gland and aluminium lugs for

following size of PVC insulated and PVC sheathed /

XLPE aluminium conductor cable of 1.1 KV grade

as required.

a) 9.1.32 4x6 sqmm set 30 203 6090

b) 9.1.32 4x10 sqmm set 4 203 812

c) 9.1.11 3.5*50 sqmm set 8 286 2288

d) 9.1.12 3.5*70 sqmm set 2 361 722

e) 9.1.13 3.5*95 sqmm set 8 431 3448

Total carried over to summary ₹


SUBHEAD -XVIII . EXTERNAL LIGHTING

Hospital

18.01 N.S.R.

Supplying of 6 mtr High 3 mm thich Octagonal GI

Pole along with base plate 200x200x12 mm

thick,foundation bolt size 4 nos 20 mm dia ,600 mm

long ,200 mm pitch circle dia (PCD) and 100 mm

projected bolt length suitable for 600 mm long for

pole having top70 mm dia and bottam 130 mm dia

A/F single bracket ,suitable for 60 watt LED

luminairs

Each 23 27002 621046

18.02 N.S.R.

Supplying of 3 mtr High 3 mm thich Octagonal GI


thick,foundation bolt size 4nos 16 mm dia ,450 mm




A/F single bracket ,suitable for 40 watt LED lamp

luminairs

Each 15 20516 307740



18.03 N.S.R.

Supplying & assambling single arm bracket 1.0 mtr

long for pole having top 70 mm A/F t ,suitable for

60 watt LED

each 23 2461 56603

18.04 11.3.1

Erection of metallic pole of following length in

cement concrete 1:3:6 (1 cement : 3 coarse sand :

6 graded stone aggregate 40 mm nominal size)


required.

each 57 2760 157320

upto 6.5 meter

18.05

Providing, laying and fixing following dia G.I. pipe

(medium class) in ground complete with G.I. fittings

including trenching (75 cm deep) and re-filling etc.

as required

i) 14.13.3 100 mm dia for Gate crossing Mtr 20 828 16560

ii) 14.13.4 150 mm dia for bridge crossing Mtr 20 1265 25300

18.06

Supplying and laying of following size DWC HDPE

pipe ISI marked along with all accessories like

socket, bend, couplers etc. conforming to IS 14930,

Part II complete with fitting and cutting, jointing etc.

in the existing trench, complete as required.

14.15.163 mm dia (OD-63 mm & ID-51 mm nominal) for

poleMtr 43 79 3397

street light

18.07

SITC of street LED light- Decorative Energy

Saving LED Street light with PDC Aluminium Body

and Clear Polycarbonate cover. Wide beam

distribution. CCT 5700K. IP 66.similar to polycab

cat no PUB0504006 PCGLS TO 70 70 W 5700 K 1

each 23 9784 225032

18.08

SITC of Post Top LED light-Powder coated PDC

Aluminium body with opal diffuser. Suitable for

landscape lighting.Available CCT 3000K. IP 54.each 15 12218 183270

18.09

SITC of LED Flood Light- Energy Saving LED

Flood light, powder coated PDC Aluminium body

with toughened glass visor fitted in frame. Efficacy

> 90 Lm/W.Available CCT 6000K. IP 65.similar to

polycab cat no-PAR0201005 PCGLF 02 80 80 W

6000 K

each 6 11535 69210

solar street light

18.10

SITC of solar stand alon street light system

includes 20 watts LED street Light DC Luminaire ,

100 Wp SPV Panel module capacity , 12V / 75 Ah

Lead Acid Battery, 5 mtr Powder Coated MS pole

each 19 36627.5 695922.5

18.11

Providing, laying and fixing following dia RCC pipe

NP2 class (light duty) in ground complete with RCC

collars, jointing with cement mortar 1:2 (1 cement :

2 fine sand) including trenching (75 cm deep) and

refilling etc as required.

i) 14.14.1 100 mm dia mtr 50 355 17750

ii) 14.14.2 150 mm dia mtr 100 405 40500

iii) 14.14.3 250 mm dia mtr 100 478 47800



b HOUSING

18.12

N.S.R. Supplying of 6 mtr High 3 mm thich Octagonal GI


thick,foundation bolt size 4 nos 20 mm dia ,600 mm




A/F single bracket ,suitable for 60 watt LED

luminairs

Each 16 27002 432032

18.13

N.S.R. Supplying of 3 mtr High 3 mm thich Octagonal GI


thick,foundation bolt size 4nos 16 mm dia ,450 mm




A/F single bracket ,suitable for 40 watt LED lamp

luminairs

Each 7 20516 143612

18.14

N.S.R. Supplying & assambling single arm bracket 1.0 mtr

long for pole having top 70 mm A/F t ,suitable for

60 watt LED

each 16 2208 35328

11.3.1 Erection of metallic pole of following length in

cement concrete 1:3:6 (1 cement : 3 coarse sand :

6 graded stone aggregate 40 mm nominal size)


required. upto 6.5 meter

each 35 2760 96600


(medium class) in ground complete with G.I. fittings

including trenching (75 cm deep) and re-filling etc.

as required

14.13.3 100 mm dia for Gate crossing Mtr 10 828 8280

14.13.4 150 mm dia for bridge crossing Mtr 20 1265 25300

Supplying and laying of following size DWC HDPE

pipe ISI marked along with all accessories like

socket, bend, couplers etc. conforming to IS 14930,

Part II complete with fitting and cutting, jointing etc.

in the existing trench, complete as required.

14.15.1 63 mm dia (OD-63 mm & ID-51 mm nominal) for

poleMtr 30

792370

street light

18.15

SITC of street LED light- Decorative Energy

Saving LED Street light with PDC Aluminium Body

and Clear Polycarbonate cover. Wide beam

distribution. CCT 5700K. IP 66.similar to polycab

cat no PUB0504006 PCGLS TO 70 70 W 5700 K 1

each 16 9784 156544

18.16

SITC of Post Top LED light-Powder coated PDC

Aluminium body with opal diffuser. Suitable for

landscape lighting.Available CCT 3000K. IP 54.each 7 12218 85526

Solar street light



18.17

SITC of solar stand alon street light system

includes 20 watts LED street Light DC Luminaire ,

100 Wp SPV Panel module capacity , 12V / 75 Ah

Lead Acid Battery, 5 mtr Powder Coated MS pole

each 12 36627 439524

18.18

Providing, laying and fixing following dia RCC pipe

NP2 class (light duty) in ground complete with RCC

collars, jointing with cement mortar 1:2 (1 cement :

2 fine sand) including trenching (75 cm deep) and

refilling etc as required.

a) 14.14.1 100 mm dia mtr 20 355 7100

b) 14.14.2 150 mm dia mtr 50 405 20250

c) 14.14.3 250 mm dia mtr 30 478 14340


SUBHEAD - XIX . DIESEL GENERATOR

19.01 Sub-head 'A' (Equipments)

19.01

SITC of “Silent Type” following KVA Sound

Attenuated DG Set comprising of engine coupled to

415V, following KVA alternator mounted on a

common Base Frame along with other accessories

i.e. Engine Control Panel Auto/Manual (Mounted on

Engine), Fuel tank, Batteries with leads i/c AMF

Panel etc. as reqd. complete. The DG Set should

be supplied with cable end box to accommodate

suitable size and no. of cable on alternator

complete as reqd. The canopy should be designed

in such a way so that the Noise level can be

restricted to 75 db level at a distance of 1 meter

away from the DG Set.

a)Diesel Engine:

Diesel engine 4 stroke, water cooled, electric start,

of suitable BHP at 1500 RPM suitable for following

KVA output of alternator at 40 Degree C, 50%RH &

at 1000 Meter MSL and conforming to BS 5514, BS

649, IS 10000, capable of taking 10% over loading

for one hour after 12 hours of continuous operation.

The engine will be fitted complete with all the

required accessories.

b) Engine mounted Instrument Panel

(Auto/Manual) fitted with and having digital

display for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lub. Oil trip pressure indication

(ix) Engine Hours indication

c) Alternator :



Synchronous alternator rated at following KVA, 415

volts at 1500 RPM, 3 phase 50 Hz, AC supply with

0.8 lagging power factor at 40 Degree C, 50% RH &

at 1000 Meter MSL. The alternator shall be having

SPDP enclosure, brushless, continuous duty, self-

excited and self-regulated through AVR conforming

to IS: 4722/BS 2613 suitable for tropical conditions

and with class-F/H insulation.

d)Base Frame & Foundation FOR Engine and

Alternator:

Both the engine and alternator shall be mounted on

suitable base frame made of MS channel with

necessary reinforcement which shall be installed on

suitable cement concrete foundation and vibration

isolation arrangement as per recommendations of

manufacturer.

e)Base Frame & Foundation For Daily Service

Fuel Tank:

Daily service fuel tank of 990 liters capacity

fabricated out of 3mm thick M.S. sheet complete

with all standard accessories and fuel piping

between fuel tank and diesel engine with MS class

'C' pipes of suitable dia. Complete with valves, level

indications & accessories as required as per

specifications.

f) Exhaust System:

Dry exhaust manifold with hospital exhaust silencer

and catalytic convertor.

g) Starting System:

24v DC starting system comprising of starter

motors: voltage regulator and arrangement for

initial excitation complete with suitable nos. of

batteries (25 plates, 180 Amp / as per OEM.-Hour

capacity lead acid type) as required as per

specifications.

h) Acoustic and weather proof enclosure

Acoustic and weather proof enclosure with

arrangement for fresh air intake for cooling of the

engine & alternator, extraction, discharging hot air

into the atmosphere as per specifications.

19.01-A a ) 500 KVADG Set Set 1 3625351 3625351

19.01-B b ) 250 KVADG Set Set 1 2154795 2154795

19.01.2

Supplying, Installing, Testing and Commissioning at

site of automatic mains failure control including

auto by-pass panel, suitable for 500 KVA silent

type Dg set complete with relays, timers, set of CTs

for metering & protection and energy analyser to

indicate currents, phase and line voltages,

frequency, power factor, KWH, KVARH & provision

for overload, short circuit, restricted earth fault,

under frequency, control cabling from AMF panel to

diesel engine and elsewhere if required, all

complete and inter locking including the folloewing

and as per specification.:



(a)

1 No. 800 amps 4 pole electrically operated

electrically draw out type air circuit breaker with

microprocessor release unit for short circuit, over

current ,shunt trip. and earth fault protection with

adjustable setting including suitable rating of CT's

as required and as per specification .

(b) Auto/Manual/Test/Off selector switch

(c) 1 Nos. reverse power relay .

(d)3 Sets of current transformers 15 p 10 accuracy for

protection and 15 VA class-1 for metering

(e)Energy analyser unit to indicate current voltage

frequency power factor and KWH

(f) Indicating lamps for load on mains and load on set

(g) MCB for instruments

(h)

Battery charger, complete with transformer/rectifier,

D.C. voltmeter and ammeter, selector switch for

trickle, off and boost and current adjustment.

(i) Main supply failure monitor

(j) Supply failure timer

(k) Restoration timer

(l)Control unit with three impulse automatic engine

start/stop and failure to start lockout.

(m) Impulse counter with locking and reset facility.

(n) ON/OFF/Control circuit switch with indicator

(o) Audio/Video annunication for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning set 1 535156 535156

19.01.3

Supplying, Installing, Testing and Commissioning at

site of automatic mains failure control including

auto by-pass panel, suitable for 250 KVA silent

type Dg set complete with relays, timers, set of CTs

for metering & protection and energy analyser to

indicate currents, phase and line voltages,

frequency, power factor, KWH, KVARH & provision

for overload, short circuit, restricted earth fault,

under frequency, control cabling from AMF panel to

diesel engine and elsewhere if required, all

complete and inter locking including the folloewing

and as per specification.:

(a)

1 No. 630 amps 4 pole electrically operated

electrically draw out type air circuit breaker with

microprocessor release unit for short circuit, over

current ,shunt trip. and earth fault protection with

adjustable setting including suitable rating of CT's

as required and as per specification .

(b) Auto/Manual/Test/Off selector switch

(c) 1 Nos. reverse power relay .



(d)3 Sets of current transformers 15 p 10 accuracy for

protection and 15 VA class-1 for metering

(e)Energy analyser unit to indicate current voltage

frequency power factor and KWH

(f) Indicating lamps for load on mains and load on set

(g) MCB for instruments

(h)

Battery charger, complete with transformer/rectifier,

D.C. voltmeter and ammeter, selector switch for

trickle, off and boost and current adjustment.

(i) Main supply failure monitor

(j) Supply failure timer

(k) Restoration timer

(l)Control unit with three impulse automatic engine

start/stop and failure to start lockout.

(m) Impulse counter with locking and reset facility.

(n) ON/OFF/Control circuit switch with indicator

(o) Audio/Video annunication for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning set 1 535156 535156

FOUNDATION

19.02

14.1 Providing and laying in position reinforced cement


graded stone aggregate 20 mm nominal size) in

foundation of pump, DG set etc. including form

work etc. as required (excluding reinforcement).

cum 5487

CUM 15.144 5487 83095

19.03

For “Operation and Comprehensive

maintenance of 500 KVA & 250 KVA DG Sets”

after DLP

Description of Work

1Operation Charges for 500 & 250 KVA DG Sets

during DLP including all taxes

Per

annum

per set

2

Operation and comprehensive annual

maintenance charges for 500 & 250 KVA DG

Sets for 1st year after DLP

Per

annum

per set

3



Sets for 2nd year after DLP

Per

annum

per set

4



Sets for 3rd year after DLP

Per

annum

per set

5


maintenance charges for 500 & 250 KVA DG Sets

for 4th year after DLP

Per

annum

per set


SUBHEAD - XX . UPS SYSTEM



20.01

SUPPLYING, testing & commissioning of 3 x 100

KVA True Online double conversion and fully

Microprocessor Controlled UPS system with IGBT

Rectifier and connected in “Parallel Redundant

load sharing Configuration.” including RS 485

Modbus Communication port with inbuilt galvanic

and electronic isolation at the output with

accessories and suitable Power Management

software in each UPS as per specification Suitable

for SERVER , COMPUTER , TELEPHONE

EXCHANGE ,FAX MACHINE , CCTV,PA SYSTEM,

,BMS SYSTEM , MEDICAL EQUIPMENTS & FIRE

ALARM PANEL load

Nos. 3 1617187.5 4851562.5

UPS SYSTEM ALONG WITH SMF BATTERY

BACKUP USING 12V BATTERIES OF APPROVED

MAKE EQVT MAKE, DISCONNECTOR FOR

BATTERY PROTECTION, MS RACK,

INTERLINKS AND DC CABLE UPTO 10 MTRS

FROM UPS TO BATTERIES.

12VDC /120AH X40 Nos./UPS /as per vender

calculation

Including supplying , testing & commissioning of

APPROVED MAKES 100 KVA 3PH-3PH TRUE

ONLINE UPS SYSTEM IN PARALLEL

CONFIGURATION ALONG WITH SMF BATTERY

OF 12V-120 AH-40 NOS FOR UPTO 20 MIN .

BACK-UP BATTERY AS PER APPROVED MAKE ,

UPS- APPROVED MODEL WITH MS

RACK,INTERLINKS AND DC CABLE UPTO 5

MTRS FROM UPS TO BATTERIES. (20Min.

Back-up (3UPS IN Parallel )

SPECIAL FEATURES :

IGBT BASED RECTIFIER AND INVERTER

INPUT VOLT 415V - 15% + 10%, THREE PHASE

4 WIRE

OUTPUT VOLT 415V +/- 1%, THREE PHASE 4

WIRE

OVERALL EFFICEINCY UPTO 94%

OUTPUT FREQUENCY 50 HZ +/- 0.1 HZ

INPUT POWER FACTOR >0.99, CURRENT

HARMONICS <3%

OUTPUT POWER FACTOR 0.9 LAGGING

INBUILT ISOLATION TRANSFORMER

Inclusive SUPPLYING OF BATTERY

ACCESSORIES

a) Battery Rack for 100 KVA UPS

b)Battery Interconnecting Links for 100 KVA UPS

c) Battery to UPS Cable (Maximum 10 meters) for

100 KVA UPS

d) Battery Fuse Box for 100 KVA UPS.

20.02

INSTALLATION AND COMMISSIONING OF 100

KVA UPS WITH BATTERY AND ACCESSORIES

set 3 23000 69000



20.03

SUPPLYING, testing & commissioning of 1 x 10

KVA True Online double conversion and fully

Microprocessor Controlled UPS system with IGBT

Rectifier including RS 485 Modbus

Communication port with inbuilt galvanic and

electronic isolation at the output with accessories

and suitable Power Management software in each

UPS as per specification Suitable for OT load

Nos. 3 162366 487098

UPS SYSTEM ALONG WITH SMF BATTERY

BACKUP USING 12V BATTERIES OF APPROVED

MAKE EQVT MAKE, DISCONNECTOR FOR

BATTERY PROTECTION, MS RACK,

INTERLINKS AND DC CABLE UPTO 5 MTRS

FROM UPS TO BATTERIES.

12vdc, 26Ahx15 Nos./UPS / as pervender

calculation

including Supplying , testing & commissioning of

APPROVED MAKES 10 KVA 1PH-1PH TRUE

ONLINE UPS SYSTEM (Standalone) ALONG

WITH SMF BATTERY OF 12V-26 AH-15 NOS

FOR UPTO 20 MIN . BACK-UP BATTERY AS PER

APPROVED MAKE , UPS- APPROVED MODEL

WITH MS RACK,INTERLINKS AND DC CABLE

UPTO 10 MTRS FROM UPS TO BATTERIES.

SPECIAL FEATURES :

IGBT BASED RECTIFIER AND INVERTER

INPUT VOLT 230V - 15% + 10%, SINGLE PHASE

4 WIRE

OUTPUT VOLT 230V +/- 1%, SINGLE PHASE

&NEUTRAL

OVERALL EFFICEINCY UPTO 94%

OUTPUT FREQUENCY 50 HZ +/- 0.1 HZ

INPUT POWER FACTOR >0.99, CURRENT

HARMONICS <3%

OUTPUT POWER FACTOR 0.9 LAGGING

INBUILT ISOLATION TRANSFORMER

SUPPLYING OF BATTERY ACCESSORIES

a) Battery Rack for 10 KVA UPS

b)Battery Interconnecting Links for 20 KVA UPS

c) Battery to UPS Cable (Maximum 10 meters) for

10 KVA UPS

d) Battery Fuse Box for 10 KVA UPS.

20.04

INSTALLATION AND COMMISSIONING OF 10

KVA UPS WITH BATTERY AND ACCESSORIES

set 3 5175 15525

Total carried over to summary 5423186

GRAND TOTAL 79098581


(DSR-2016) UNIT QUT. RATE

Item NO (IN FIGURES) AMOUNT (IN RS.)

SUBHEAD-I(A): FIRE PUMPS AND HYDRANT WORKS (NON SCHEDULED ITEMS)

1.1 M.R. FIRE PUMPS - ELECTRICAL

Supply, installation, testing and

commissioning of horizontal single stage

centrifugal type factory assembled fire

pumps suitable for autometic operation at

synchoronous speed of 2900 rpm, TEFC

conforming to IP-55 & flexible coupling

gaurd mounted on a common structural

base plate with 150mm dia gun metal

pressure gauges with isolation cock and

piping, suitable vibration elimination pads

of approved design for pump foundation,

motor to be suitable for 415 volts, 3 phase

50 cycles AC.

1.1.1

Capacity 2280 LPM at 7.0 Kg/cm2 delivery

pressure for Fire Hydrant Network.

Set 1 381,225.00 381,225.00

1.1.2

Capacity 180 LPM at 7.0 Kg/cm2 (Jockey

Pump). Set 1 111,435.00 111,435.00

1.3.1

Capacity 900 LPM at 3.5 Kg/cm2 (Roof Fire

Pump). Set 3 134,895.00 404,685.00

ROOF PANELS:Supply, installation, testing and

commissioning of following integrated,

cubicle type,dead front, extensible, sheet

steel control panel. The panel shall be

suitable for 440 volts, 50 cycles, 4 wire

supply

The following components and accessories

shall be mounted with ineach control

panel.

One no 60 amps TP incoming MCCB with

the following:

0-500 volts 96 x96 square mm voltmeter

with slector switch and control fuses- 1

SET

0-100 amps 96 x96 square mm ammeter

with CT's and slector switch- 1 SET

Phase indicating lamp with toggle

switches.

Indication lamps for ON/OFF/TRIP status

Outgoing Feeders / Starters as below:

60 ATP MCCB with star / delta as starter

suitable for 15 HP motor for Downcomer

Pump - 1 Set

S. NO. DESCRIPTION


Schedule of Items - Fire fighting- BOQ




S. NO. DESCRIPTION

Provision in control panel to connect flow

switch for autmatic operation of roof fire

pumps.

1.2 M.R. FIRE PUMPS - DIESEL


commissioning of horizontal single stage

centrifugal pumping set with CI volute and

bronze impeller with mechanical seals

directly coupled to automatic Diesel

Engine complete with all accessories like

self starting by means of Battery powered

electric starter motor, Paper Filter type air

cleaner, exhaust silencer etc. complete in

all respects. The engine & the pump will

be mounted on common base plate on

anti-vibration mountings.

Capacity 2280 LPM at 7.0 Kg/cm2 delivery

pressure for Fire Hydrant & Sprinkler

Network. Set 1 639,285.00 639,285.00

Exhaust piping

1.3 M.R.

Providing & fixing 150 mm diameter M.S.

Class 'C' diesel pump exhaust pipe

includings all fittings, like bends, tees etc.

clamps / structural steel supports. The

pipe shall be provided with 75mm thick

fiberglass insulation & covering the

insulation with 500 g polythene sheet

giving proper overlaps & sealing the joints

with suitable adhesive compound. The

pipe shall be provided with 24 gauge

aluminium sheet cladding

RM 20 1,712.35 34,246.91

1.5 M.R. PRESSURE SWITCH

1.5.1

Supplying, installing, testing and

commissioning 0 to 12 Kg/ cm2 ON/OFF

pressure switch in delivery line of pump

along with control wiring for auto starting

and auto stopping of hydrant and jockey

pumps. Each 6 4,855.07 29,130.42

1.6 M.R.

Supply, fabrication (as per code),

installation, testing and commissioning of

Pressure vessels 450mm diameter and

1000mm high fabricated from 8-10mm

M.S. plate with accessories inside painting

with epoxy paint and outside with enamel.

Each 1 19,309.94 19,309.94




S. NO. DESCRIPTION

1.7 M.R.

Providing, fixing, testing & commissioning

of resilient rubber lined single arch

vibration eliminators suitable for raw

water up to 45 deg. C temperature,

working pressure 8.8 Kg/cm2 and test

pressure 14 Kg/cm2 for :-

1.7.1 150 mm dia Each 4 5,014.58 20,058.30

100 mm dia Each 7 3,989.37 27,925.61

80 mm dia Each 1 3,287.33 3,287.33

1.8 M.R.

Supply, installation, testing, trial run and

commissioning of hydrants all complete as

required and as approved

1.8.1 Fire Hose Cabinet

1.8.1.1

1.6mm thick MS door frame 900x2100

door capable of accommodating fire hose

reel, landing valve, hose pipes, fittings &

accessories. The door shall have a front

glass with lock and key arrangement &

shall be painted with post office red colour

(approval shall be taken on the basis of

submitted sample before ordering) Cost of

fire extinguishers not included in item

rate. (Liasioing with civil contractor for

making 900x600x2100 Recessed type

mansoary box (by civil contractor).

Each 28 36,949.50 1,034,586.00

1.8.1.2

TAC approved 1.6mm thick M.S. fire hose

cabinet (750x600x250mm) made out of 16

gauge M.S. sheet capable of

accommodating landing valve, hose pipes,

fittings & accessories. The box shall have a

front glass door with lock and key

arrangement & shall be painted with post

office red colour (approval shall be taken

on the basis of submitted sample before

ordering) - for external and roof hydrant.

Each 12 2,640.80 31,689.63

1.8.2

63mm dia single outlet GM landing valve IS

marked with suitable size bolts, nuts,

washers and gaskets. Landing valve shall

be TAC Approved Make.

Each 28 6,607.44 185,008.32

1.8.3

63mm dia twin outlet GM landing valve IS

marked with suitable size bolts, nuts,

washers and gaskets. Landing valve shall

be TAC Approved Make.

Each 6 13,986.47 83,918.84

1.8.4

First aid hose reel with 25 mm dia, 30 m

long rubber hose, ball valve, piping and

GM nozzle Each 28 3,966.64 111,065.85




S. NO. DESCRIPTION

1.8.5

63mm reinforced rubber hoses (RRL) with

male and female GM coupling, IS marked-

15 m long Each 68 5,520.69 375,406.92

1.8.6

standard short size GM branch pipe with

nozzle of 20mm nomnal bor outlet with

instaneous type 63 mm dia coupling

complete IS marked & TAC approved.

Each 34 2,173.50 73,899.00

1.8.7 Fire Axe Each 28 516.21 14,453.78

1.9 M.R.


commissioning ss orifice plates in pipelines

to reduce pressure from 8 kg. to 3.5

kg/sq.cm. Each 47 1,304.10 61,292.70

1.10 M.R.

Providing, installing, testing &

commisioning of fire brigade inlet

connection (fire department connection)

consisting of 4 Nos. 63 mm dia

instantaneous inlet arranged on a 50 mm

dia header, 1 No. 150 mm diameter

Butterfly valve, 1 No. 150mm dia. Non-

return valve and wall mounted box of

M.S. construction with glass door to house

the above mentioned components.

Set 5 22,785.89 113,929.44

1.11 M.R.

Providing, installing, testing &

commisioning of fire brigade draw out

connection (fire department connection)

with suction pipe MS class 'C' 100 mm dia.

& 100 mm dia. foot valve & steel chain

including wall mounted box M.S.

construction with glass door to house the

above mentioned componenets.

Set 1 12,723.07 12,723.07

TOTAL C/F TO SUMMARY 3,768,562.05




S. NO. DESCRIPTION

SUBHEAD-I (B): PIPING FOR FIRE FIGHTING SYSTEM (AS PER DSR-2016)

1.1

DSR ITEM

NO 2.10

Excavating trenches of required width for

pipes, cables, etc including excavation for

sockets, and dressing of sides, ramming of

bottoms, depth upto 1.5 m including

getting out the excavated soil, and then

returning the soil as required, in layers not

exceeding 20 cm in depth including

consolidating each deposited layer by

ramming, watering, etc. and disposing of

surplus excavated soil as directed, within a

lead of 50 m :

2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia.

but not exceeding 300 mm dia. Cum 510 225.45 114,979.50

1.2

DSR ITEM

NO 4.5

Providing and fixing up to floor five level

precast cement concrete string or lacing

courses, copings, bed plates, anchor

blocks, plain window sills, shelves, louvers,

steps, stair cases, etc. including hoisting

and setting in position with cement mortar

1:3 (1 Cement : 3 coarse sand), cost of

required centering, shuttering and

finishing smooth with 6mm thick cement

plaster 1:3 (1 Cement : 3 fine sand) on

exposed surfaces complete.

4.5.1

1:1.5:3 (1 cement : 1.5 coarse sand : 3

graded stone aggregate 20mm nominal

size). Cum 51 6772.45 345,394.95

1.3

DSR Item

18.34.1

Constructing masonary chamber 90 x 90

x100 cm. inside with 75 class designation

brickwork in cement mortar 1:5 ( 1 cement

: 5 fine sand) for sluice valve with CI

surface box 100 mm top dia. 180 mm

bottom dia. And 180 mm deep (inside)

with chained lid and RCC top slab 1:2:4 mix

( 1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) necessary

excavation foundation concrete 1 :5 :10 (1

cement : 5 fine sand : 10 graded stone

aggregate 40 mm nominal size and inside

plastering with 1:3 (1 cement : 3 coarse

sand) 12 mm thick finished with a floating

coat of neat cement complete as per

standard design with FPS bricks

Each 11 11842.75 130,270.25




S. NO. DESCRIPTION

1.4 18.59

Providing and fixing C.I. double acting air

valves of approved quality with bolts, nuts,

rubber insertions etc. complete ( The tail

pieces, tapers etc. if reqd. will be paid

separately)

1.4.1 18.59.1 50 mm dia. Each 9 4662.45 41,962.05

1.5 18.31

Providing & Fixing C.I.sluice valve(with cap)

complete with bolts,nuts,rubber insertions

etc.(the tail pieces if required will be paid

separately)

1.5.1 18.31.3 150 mm dia.pipe

1.5.1.1 18.31.3.2 Class II Each 11 5387.2 59,259.20

1.6

ELECT. DSR

2016 /

16.7.4

Y - STRAINER of Ductile CI Body flanged

ends with stainless steel strainer for

chilled / hot water circulation including

insulation as specified.

16.7.4.2 150 mm dia. Each 2 10530 21,060.00

1.7

ELECT. DSR

2016 /

16.11.2

NON - RETURN VALVE with duel plate of C I

body SS plates vulcanized NBR seal flanged

end & PN 16 pressure rating for chilled /

hot water circulation including insulation

as specified.

A 16.11.2.5 80 mm dia Each 2 2392 4,784.00

B 16.11.2.4 100 mm dia Each 2.00 3327 6,654.00

C 16.11.2.2 150 mm dia Each 10.00 5772 57,720.00

d 16.11.2.1 200 mm dia Each 1.00 8805 8,805.00

1.8

ELECT. DSR

2016 /

16.11.1

BUTTERFLY VALVE (MANUAL) with C I body

SS Disc, Nitrile Rubber Seal & O- Ring PN

16 pressure rating for chilled water/ hot

eater circulation as specified

A 16.11.1.5 80 mm dia Each 2.00 3302 6,604.00

B 16.11.1.4 100 mm dia Each 2 4685 9,370.00

C 16.11.1.2 150 mm dia Each 8.00 5914 47,312.00

D 16.11.1.1 200 mm dia Each 1.00 10261 10,261.00

1.9

ELECT. DSR

2016 / 16.8

Providing and fixing in position the

industrial type Pressure Gauges with

gun metal / brass valves complete as

required Each 4.00 973 3,892.00

TOTAL C/F TO SUMMARY 868,327.95

SUBHEAD-II(B):PIPING FOR FIRE FIGHTING SYSTEM (NON SCHEDULED ITEMS)




S. NO. DESCRIPTION

2.1

Providing laying, testing & commissioning

of “C” class heavy duty MS pipe

conforming to IS 1239/3589 (all pipes shall

be ISI marked and of makes specified in

the specifications) i/c fittings like elbows,

tees, flanges, tapers, nuts bolts, gaskets

etc. in ground including excavation &

providing cement concrete blocks as

supports and anti-corrosive treatment to

burried pipes by wrapping & coating with 4

mm thk. (OR 2 COATS of 2mm thick tape)

anticorrosion tape along with two coat of

black japan primer for under-ground pipe

including digging and backfilling upto 1.0

mtr. below from G.L.for external work as

per IS-909 (Specification for Underground

Fire Hydrant Make: Jindal Hissar/ Surya/

Tata/ SAIL. (Under ground)

a M.R. 150 nominal bore (class C) M 440 1,883.95 828,939.02

b M.R. 100 nominal bore (class C) M 70 1,360.82 95,257.10

2.2

Providing, laying, testing & commissioning

of “C” class heavy duty MS pipe

conforming to IS 3589 and 1239 (all pipes

shall be ISI marked and shall be one of

approved makes) including fittings like

elbows, tees, flanges, tapers, nuts bolts,

gaskets etc. fixing the pipe on the

wall/ceiling with suitable clamps and

painting with two or more coats of

synthetic enamel paint of required shade

complete as per specificatipns and as

required. (Above Ground)

Note:

A

Threaded joint upto 50mm diameter pipe.

B

Welded joint above 50mm diameter pipe.

M.R. 250 mm nominal bore (class C - 9.5mm) Rm 25 5,009.92 125,248.11

a M.R. 200 mm nominal bore (class C - 9.5mm) Rm 25 4,073.56 101,839.11

b M.R. 150 mm nominal bore (class C) Rm 475 1,757.45 834,789.85

c M.R. 100 mm nominal bore (class C) Rm 977.76 1,228.57 1,201,242.40

d M.R. 80 mm nominal bore (class C) Rm 1079.56 861.24 929,761.93

e M.R. 65 mm nominal bore (class C) Rm 920.2 729.22 671,029.67

f M.R. 50 mm nominal bore (class C) Rm 904.6 572.52 517,897.77

g M.R. 40 mm nominal bore (class C) Rm 1142.5 420.10 479,967.87

h M.R. 32 mm nominal bore (class C) Rm 421 366.75 154,401.49

i M.R. 25 mm nominal bore (class C) Rm 6571.3 295.91 1,944,494.92




S. NO. DESCRIPTION

2.3 M.R.


commissioning of 150 mm dia Installation

Control Valve inclusive of 2 nos 150 mm

dia Butterfly Valve, strainer, Alarm Valve

with Water Motor Gong, Pressure Gauges,

Test Lines with Ball Valves with necessary

GI (H) piping with threaded fittings of

required sizes complete

Set 1 56,511.00 56,511.00

2.4 M.R.


commissioning of 150 mm dia Zonal

Control Valve inclusive of 1 nos 150 mm

dia butterfly valve, 150mm diam. non

return valve, Flow Switch, water pressure

gauges & 25 mm dia. Auxillary Drain valve

with sight glass with necessary GI (H)

piping with threaded fittings of required

sizes complete

Set 12 49,447.13 593,365.50

2.5 M.R.

Providing, fixing, testing and

commissioning of quick response 15 mm

dia. gunmetal quartz bulb type sprinkler

head to operate at 68 degree centigrade

Side wall type Each 100 358.63 35,862.75

Pendent / Upright type Each 2056 336.89 692,650.98

2.6 M.R.

Providing and fixing 25 mm dia, 1200mm

long flexible stainless steel (SS 304) pipe

for making final connection of sprinkler

head with sprinkler system piping network

including 2 nos. 25mm diameter G.I.

connector, G.I. Nipple, Reducer, elbow and

threaded jointing complete as per detail.

Each 546 1,756.63 959,117.25

TOTAL C/F TO SUMMARY 10,222,376.71

SUBHEAD- III (B): FIRE EXTINGUSHER (NON SCHEDULED ITEMS)

3.1 M.R.

Providing and fixing carbon-di-oxide type

fire extinguishers consisting of welded

M.S. cylindrical body, internal discharge

tube, discharge nozzle, suspension

bracket, conforming to IS 2878, finished

externally with red enamel paint and fixed

to wall with brackets complete with

internal charges.

a Capacity 4.5 kg Nos. 66 5,754.34 379,786.52




S. NO. DESCRIPTION

3.2 M.R.

Providing & Fixing of stored pressure Fire

Extinguisher ABC powder type (Mono

Ammonium Phosphate Powder) Magnetic

Pressure Gauge having the facility to check

at site, Discharge Time less than 9 Secs,

Controllable discharge mechanism, Range

minimum 4 Meters, applicable on Class

A,B,C and electrically started Fire, A Rating-

21A, B Rating 55B as per BS EN-3 BIS

15683 marked, Can Construction : Deep

drawn & CO2 Mig welded, Valve

Construction : Forging & Machining,

Internal Coating of Can : Epoxy Powder

coating, External Coating ofCan : Epoxy

Polyster Powder coating, Sheet metal

thickness : 1.60MM, Helium LeakDetection

Tested, Warranty.

a Capacity 6 Kg. Nos. 66 2,097.43 138,430.22

3.3

Providing and fixing mechanical foam

type Trolley Mounted Fire Extinguisher

of bearing to

IS:10568/IS13385/IS13386 with dis Capacity 50 Lit. Nos. 1 10,101.34 10,101.34

3.4

Providing and fixing Carbon Dioxide Type

Trolley Mounted Fire Extinguisher of as per

IS: 2878 with discharge time of 10 to 20

sec/15 to 36sec/20 to 60sec respectively.

22.5 Kg. CO2 Fire Extinguisher Nos. 1 16,708.78 16,708.78


SUBHEAD-IV (B): FIRE ELECTRICAL WORKS (NON SCHEDULED ITEMS)

4.1 MR Fabricating, supplying, testing and

commissioning of electrical control panel

of cubicle construction, floor mounted

type, fabricated out of 2mm thick crca

sheet, compartmentallised and hinged

lockable doors, dust and vermin proof,

powder coated approved shade after 7

tank treatment process, cable alley

interconnection, having switchgears and

accessories mounting and internal wiring,

earth terminals, numbering etc., complete

in all respects, suitable for operation on

415V, 3 phase 50 Hz., AC supplywith

enclosure protection class IP-42as

required.

Set 1 381,225.00 381,225.00

A COMMON PANEL IN FIRE PUMP HOUSE.




S. NO. DESCRIPTION

(i) INCOMER

(a) 400 Amps. TP & N SFU with HRC fuses.

(b) Voltmeter (0-500 Volts) with selector

switch.

(c) Ameter (0- 400 Amps.) with selector

switch & CT's etc.

(d) Set of 3 phase indicating lamp.

(e) Set of Al. bus bar 200 Amps.

(ii) OUTGOING.

(a) Main fire pump and Sprinkler pump

200 Amps. TP& N SFU with HRC fuses with

suitable HP fully automatic star/delta

starter with over load protection, current

sensing type single phase preventor

complete with all acessories and internal

wiring required for automatic operation,

selector switch for local / remote, auto/

manual OFF operation.

(b) Jockey pump

40 Amps. TP& N SFU with HRC fuses with

suitable HP fully automatic star / delta

starter with over load protection, current


complete with all accessories and internal

wiring required for automatic operation,

selector switch for local / remote, auto /

manual / OFF operation.

(c) Diesel Engine Control

Control for Diesel Engine comprising:-




S. NO. DESCRIPTION

(i) Auto / Manual selector switch & 3 attempt

starting device, timers and relays as

required, push buttons, start / stop in

manual mode.

(ii) Indication lamp for High / Low Lub. Oil

pressure, High Water Temp. and Engine

ON indication.

(iii) Battery charger suitable for 12V / 24 V DC

with boost and tickle selector switch, 0-30

V DC volt meter, 0-20A DC Ammeter.

(iv) All standard relays and acessories for

automatic operation of diesel engine.

B DIESEL ENGINE CONTROL

Control for Diesel Engine comprising:-

(a) Auto / Manual selector switch & 3 attempt

starting device, timers and relays as

required, push buttons, start / stop in

manual mode.

(b) Indication lamp for High / Low Lub. Oil

pressure, High Water Temp. and Engine

ON indication.

(c) Battery charger suitable for 12 V / 24 V DC

with boost and tickle selector switch, 0-15

V / 0-30 V DC volt meter, 0-20A DC

Ammeter.

C MAIN FIRE PUMP CONTROL

(a) 200 Amps. TP&N SFU with HRC fuses

(b) Voltmeter (0-500 Volts) with selector

switch.

(c) Ammeter (0-200 Amps.) with selector

switch, CTs etc.

(d) Set of 3 phase indication lamp.

(e) Suitable HP fully automatic Star / Delta

Starter with over load protection, current


complete with all acessories and internal

wiring required for automatic operation.

(f) Selector switch for local / remote, auto /

manual / off operation.

D SYSTEM CONTROLLER

Designing, Supply, Installation, Testing and

Commissioning of system controller to

control operation of Main Electric Fire

Pump, Diesel Pump, Pressurisation Pump,

Terrace Pump in sequence as per

specification consisting of relays, timets,

sensors, annunciation window for fault

indication, complete as per specification.





S. NO. DESCRIPTION

SUBHEAD- IV: FIRE ELECTRICAL WORKS (DSR 2016)

5.1 5.4

Supplying and Earthing with GI earth plate

600mm x 600 mm x 6mm thick including

accessories and providing masonary

enclosure with cover plate having locking

arrangement and watering pipe etc, with

charcoal/ coke and salt as required.

Set 5 4,327.00 21,635.00

5.2 5.11

Supplying and laying 25 mm x 5 mm. G.I.

strip in 40 mm dia. G.I. Pipe from earth

electrode, including connection with GI

nut, bolt, spring, washer excavation and re-

filling etc as required.

Rm 100 351.00 35,100.00

5.3 5.15

Providing & fixing 25mm x 5mm G.I. strip

on surface or in recess for connections

etc. as required. Rm 300 129.00 38,700.00

5.4 5.18

Providing and Fixing 6 SWG dia G.I. wire on

surface or in recess for loop earthing

alongwith existing surface/ recessed

conduit/ submain wiring/ cable as

required. Rm 435 23.00 10,005.00

5.5 4.1

Supplying, fabricating and installing

following size of perforated painted with

powder coating M.S. cable trays,with

perforation not more than 17.5%, in

covenient section, joined with connectors,

suspended from the ceiling with MS

suspenders including bolts & nuts, painting

suspenders etc. as required.

5.5.1 4.1.1

100 mm width X 50 mm depth X 1.6 mm

thickness Rm 70 348.00 24,360.00

5.5.2 4.1.4

300 mm width X 50 mm depth X 1.6 mm

thickness Rm 54 526.00 28,404.00

5.6 7.7.1

Laying and fixing of One number PVC

Insulated and PVC Sheathed/XLPE power

cable of 1.1 kV grade of size not exceeding

35 sqmm on surface as required.

RM 61 25.00 1,525.00

5.7 7.7

Laying and fixing of One number PVC

Insulated and PVC Sheathed/XLPE power

cable of 1.1 kV grade of folloing size on

wall surface as required.

7.7.2

Aboved 35 sq mm and upto 95 sq mm

(clamed with 25x3mm MS flat clam) RM 265 72.00 19,080.00




S. NO. DESCRIPTION

5.8 9.1

Supplying of all materials and making

terminations of 1.1 KV grade aluminium

multicore cables of the following sizes.

The work includes cable glanding using

brass plated double compression glands,

sizing the core leads, removing insulation,

fixing suitable crimping type copper lugs/

thimbles by using hydraulic crimping tools

with correct size of the dies, shaping the

leads and neatly connecting the same to

the equipment terminals.

5.8.1 9.1.25

3.5 Core 120 sq. mm. Armoured

Aluminium cable. Mtr 25 500.00 12,500.00

5.8.2 9.1.21

3.5 Core 35 sq. mm. Armoured Aluminium

cable. Mtr 155 282.00 43,710.00

5.8.3 9.1.8

3.5 Core 16 sq. mm. Armoured Aluminium

cable. Mtr 44 202.00 8,888.00

5.9

Control Cabling (PVC insulated and PVC

sheathed, armoured, Copper Conductor of

1.1 KV grade on existing cable trays).

MR 5C x 1.5 Sq. mm RM 180 160.00 28,800.00

TOTAL 272,707.00

Grand Total 16,058,225.56


S. NO. (DSR-

2016)

No.DESCRIPTION UNIT QTY. RATE AMOUNT

1 17.1 Providing and fixing water closet squatting pan

(Indian type W.C. pan ) with 100 mm sand cast

Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with

manually controlled device (handle lever)

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making

good the walls and floors wherever required :

17.1.1 White Vitreous china Orissa pattern W.C. pan of

size 580x440 mm with integral type foot restsEach 29 3,494.20 101,331.80

2 17.2 Providing and fixing white vitreous china pedestal

type water closet (European type W.C. pan) with

seat and lid, 10 litre low level white P.V.C. flushing

cistern, including flush pipe, with manually

controlled device

(handle lever), conforming to IS : 7231, with all

fittings and fixtures complete, including cutting

and making good the walls and floors wherever

required : Each 166 3,418.70 567,504.20

17.2.1 W.C. pan with ISI marked white solid plastic seat

and lid

3 17.7 Providing and fixing wash basin with C.I.brackets,

15 mm C.P. brass pillar taps, 32 mm C.P. brass

waste of standard pattern, including painting of

fittings and brackets, cutting and making good the

walls where required :

4 17.7.1 White vitreous china flat back wash basin size 630

x 450 mm with a pair of 15 mm C.P. brass pillar

taps. Each 163 2,298.55 374,663.65

5 17.7A Providing and fixing wash bashin with C.I. brackets,

15mm dia cp brass singal hole basin mixer of

approved quility and make, including painting of

fittings and brackets, cutting and making good the

walls wherever required -a) White vitreous china wash basin size 550x400

mm with a 15 mm cp brass singal hole basin mixer.Each 37 2984.2 110,415.40

6 8.10 Providing & fixing stone slab table rubbed, edges

rounded and polished of size 75 X 50cm deep and

1.8 cm thick fixed in urinal patitions by cutting

chase of appropriate width with chase cutter and

embedding the stone in chase with epoxy grout or

with cement concrete 1:2:4 ( 1 cement : 2 coarse

sand : 4 graded stone aggregste 6mm nominal

size) as per Engineer-in-charge and finished

smooth 8.10.1 White Agaria Marble Stone sqm 34 2,831.95 96,286.30


schedule of items : Plumbing Work - BOQ

SUBHEAD-I (A): SANITARY INSTALLATIONS (As per D.S.R.2016)


S. NO. (DSR-

2016)


7 17.80 Providing and fixing white vitreous china battery

based infrared sensor operated urinal of approx.

size 610 x 390 x 370 mm having pre & post

flushing with water ( 250 ml & 500 ml

consumption), having water inlet from back side,

including fixing to wall with suitable brackets all as

per manufacturers specification and direction of

Engineer-in-charge.. Each 34 5,162.20 175,514.80

8 17.10 Providing and fixing Salem Stainless Steel A ISI 304

(18/8) kitchen sink as per IS: 13983 with CI

brackets and stainless steel waste with plug 40mm

including painting of fittings and brackets, cutting

and making good the walls wherever required.

17.10.

1

Kitchen sink with drain board

17.10.

1.3

510X1040mm bowl depth 200mm.Each 34 3,772.35 128,259.90

17.10.

2 Sink without drain board (For JC)

17.10.

2.1 610X510 mm bowl depth 200mm. Each 20 2,476.60 49,532.00

9 17.11 Providing and fixing white vitreous china

laboratory sink with C.I. brackets, C.P. brass chain

with rubber plug, 40 mm C.P brass waste and

40mm C.P. brass trap with necessary C.P. brass

unions complete, including painting of fittings and

brackets, cutting and making good the wall

wherever required :

17.11.

1 Size 450x300x150 mm Each 4 2,392.60 9,570.40

10 17.28 Providing & fixing PVC waste pipe for sink

oncluding PVC waste fitting Complete 17.28.

2

Flexible Pipe

17.28.

2.1

32mm DiaEach 58 73.25 4,248.50

11 17.32 Providing and fixing mirror of superior glass (of

approved quality) and of required shape and size

with plastic moulded frame of approved make and

shade with 6 mm thick hard board backing :

17.32.

1

Rectangular shape 453x357 mmEach 194 752.80 146,043.20

12.0 17.70 Providing and fixing PTMT Bottle Trap for Wash

basin and sink.17.70.

1

Bottle trap 31 mm single piece moulded with

height of 270 mm, effective length of tail pipe 260

mm from the centre of the waste coupling 77 mm

breadth with 25 mm minimum water seal,

weighing not less than 260 gms. Each 200 293.95 58,790.00


S. NO. (DSR-

2016)


17.70.2 Bottle trap 38 mm single piece moulded with

height of 270 mm, effective length of tail pipe 260

mm from the centre of the waste coupling 77 mm

breadth with 25 mm minimum water seal,

weighing not less than 260 gms.(sink & urinal)Each 92 305.55 28,110.60

14 17.71 Providing and fixing PTMT liquid soap container

109 mm wide, 125 mm high and 112 mm distance

from wall of standard shape with bracket of the

same materials with snap fittings of approved

quality and colour weighing not less than 105 gms.Each 250 137.85 34,462.50

15.00 17.72 Providing & fixing PTMT towel ring trapezoidal

shape 215 mm long 200 mm wide with minimum

distance of 37 mm from wall face with concealed

fittings arrangement of approved quality and

colour weighing not less than 88 gmsEach 178 197.55 35,163.90

16.00 18.49 Providing and fixing C.P. brass bib cock of

approved quality confirming to IS:8931

18.49.

1

15mm nominal boreEach 227

371.70 84,375.90

17 18.51 Providing and fixing C.P. brass long body bib cock

of approved quality conforming to IS standards

and weighing not less than 690 gms.

18.51.

1


492.55 28,567.90

18 18.53 Providing and fixing C.P. brass angle valve for

basin mixer and geyser points of approved quality

conforming to IS 8931 a) 15 mm nominal bore.

18.53.

1

15 mm nominal bore Each 989 475.70 470,467.30

19.00 17.34 Providing and fixing toilet paper holder :

17.34.

1

C.P. brassEach 187 385.35 72,060.45

20 17.73 Providing and fixing PTMT towel rail complete

with brackets fixed wooden cleats with CP brass

screws with concealed fittings arrangement of

approved quality and colour.

17.73.

2

600 mm long towel rail with total length of 645

mm, width 78 mm and effective height of 88 mm,

weighing not less than 190 gms Each 90 422.7 38,043.00

21 17.16

A

Providing and fixing 8 mm dia C.P. / S.S. Jet with

flexible tube upto 1 metre long with S.S. triangular

plate to Eureopean type W.C. of quality and make

as approved by Engineer - in-chargeEach 80 254.8 20,384.00


S. NO. (DSR-

2016)


22 18.22 Providing and fixing CP Brass shower rose with 15

or 20 mm inlet18.22.

1

100 mm diameterEach 90 71.65 6,448.50

TOTAL 2,640,244.20

1 Providing and fixing cast iron trap of self cleansing

design with cast iron screwed down or hinged

grating with or without vent arm complete,

including cost of cutting and making good the

walls and floors.17.60.

1

100 mm inlet and 100 mm outlet centrifugally

cast (spun) iron S&S. Each 300 1,034.45 310,335.00

17.60.

2

100 mm inlet and 75 mm outlet centrifugally cast

(spun) iron S&S. Each 112 1,034.45 115,858.40

2 17.35 Providing and fixing soil, waste, vent and rain

water pipes Centrifugally cast (spun) iron S&S pipe

17.35.

1.2

100mm dia cast (spun) iron S&S pipe

Rm 2257.5 921.65 2,080,624.88

3.0 17.37 Providing and fixing MS holder bat clamps of

approved design to cast iron (spun) pipe

embedded in and Including cement concrete

blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20mm

nominal size) including cost of cutting holes and

making good the walls etc.17.37.

1

For 100mm dia. PipeEach 717 140.65 100,846.05

4.0 17.38 Providing and fixing bend of required degree with

access door, insertion rubber washer 3mm thick,

bolts and nuts complete.17.38.

1

100x100x100mm

17.38.

1.2

Centrifugally cast (spun) iron pipe S&SEach 480 384.90 184,752.00

5 17.39 Providing and fixing plain bend of required degree.

17.39.

1

100mm dia

17.39.

1.2

Sand cast iron S&S as per IS : 3989Each 312 307.10 95,815.20

6 17.40.

1.2

Providing and fixing heel rest sanitary bend, in

100mm Centrifugally cast (spun) iron pipe S&S Each 178 370.95 66,029.10

7 17.42 Providing and fixing double equal plain junction of

required degree. 17.42.

1

100x100x100x100 mm

17.42.

1.2

Sand cast iron S&S as per IS - 3989Each 178 747.30 133,019.40

SUBHEAD-II(A): INTERNAL DRAINAGE INSTALLATIONS (As per D.S.R.2016)


S. NO. (DSR-

2016)


8 17.43 Providing and fixing single equal plain junction of

reqd. degree with access door, insertion rubber

washer 3mm thick, bolts and nuts complete.

17.43.

1

100x100x100mm

17.43.

1.2

Standard cast (spun) iron pipe IS-3989Each 178 623.00 110,894.00

9.00 17.44 Providing and fixing single equal plain junction of

required degree :17.44.

1

100X100X100mm

17.44.

1.2


10 17.48 Providing and fixing single unequal plain junction

of required degree17.48.

1

100x 100x75 mm

17.48.

1.2

Sand cast iron S&S as per IS -3989Each 178 689.20 122,677.60

11 17.55 Providing and fixing door piece, insertion rubber

washer 3mm thick, bolts & nuts complete :

17.55.

1

100 mm

17.55.

1.2

Providing and fixing door piece, insertion rubber

washer 3mm thick, bolts and nuts complete, in

100mm Centrifugally cast (spun) iron pipe S&SEach 178 512.65 91,251.70

12 17.56 Providing and fixing terminal guard:

17.56.

1

100mm

17.56.

1.2


13.00 17.57 Providing and fixing collar.

17.57.

1

100mm

17.57.

1.2

Centrifugally cast (spun) iron pipe S&SEach 57 351.20 20,018.40

14.00 17.65 Painting sand cast iron / centrifugally cast iron(

spun) iron soil, waste and vent pipes and fittings

with paint of any colour such as chocolate, grey or

buff etc. over a coat of primer (of approval quality)

for new work17.65.

1

100mm dia cast (spun) iron S&S pipeRm 1144 40.65 46,503.60

15 18.28 Providing lead caulked joints to spun iron or C.I.

pipes and specials, including testing of joints but

excluding the cost of pig lead :18.28.

1

100 & 150 mm diameter pipeEach 7224 224.65 1,622,871.60


S. NO. (DSR-

2016)


16 18.58 Providing and fixing PTMT grating of approved

quality and colour18.58.

1

Circular type

18.58.

1.1

100 mm nominal diaEach 312 32.75 10,218.00

17.00 19.2 Providing and laying cement concrete 1:5:10 (1

cement: 5 coarse sand: 10 graded stone aggregate

40 mm nominal size) alround SW including bed

concrete as per standard design

Note: This work shall be done all-round CI pipe at

ground floor's toilet.19.2.1 100mm diameter Rm 1113.5 622.95 693,654.83

18 19.18 Supplying and fixing C.I. cover without frame for

manholes :19.18.

3

560 mm diameter C.I. cover (heavy duty) the

weight of the cover to be not less than 108 kg Each 5,891.20 -

19 12.41 Providing & fixing on wall face unplasticised -Rigid

PVC rain water pipes conforming to IS:13592

Tyape A included jointing with seal ring conforning

to IS:5382 leaving 10 mm gap for thermal

expansion. (i)Single socketed pipes.

12.41.

2

110 mm diameter Metre1,146.00 231.65 265,470.90

20 12.42. Providing, fixing on wall face unplasticised - PVC

moulded fittings /accessories for unplasticised -

Rigid PVC rain water pipes conforming to IS ;

13592 Type A including jointing with seal ring

conforming to IS ; 5382 leaving 10 mm gap for

thermal expansion.12.42.

1.2

Coupler -110 mm diameter Each52 138.30 7,191.60

12.42.

5.2

Bend -87.5 deg -110 mm diameter Each52 161.55 8,400.60

12.42.

6.2

Shoe -110mm shoe Each52 295.10 15,345.20

21 12.43 Providing & fixing unplasticised - PVC pipe clips of

approved design to unplasticised - PVC rain water

pipes by means of 50x50x50mm hard wood plugs,

screwed with .M.S. screws of required length

including cutting brick work and fixing in cement

mortar 1:4(1cement : 4 coarse sand) and making

good the wall etc. complete.

12.43.

2

110 mm dia Each393 189.05 74,296.65

22 7760 P/F M.S. cap 100 mm dia Each 62 150.00 9,300.00

TOTAL 6,306,822.50

SUBHEAD-III(A): WATER SUPPLY INSTALLATIONS (As per D.S.R.2016)


S. NO. (DSR-

2016)


1 17.30 Providing and fixing in position 25 mm diameter

mosquito proof coupling of approved municipal

design. Each 6 38.50 231.00

2 18.7 Providing and fixing CPVC pipes having thermal

stability for hot and cold water supply including all

CPVC plain and brass threaded fittings including

fixing the pipe with clamps at 1.00 mt spacing. this

includes jionting of pipes and fittings with one step

CPVC solvent cement and testing of joints

complete as per direction of engineer in charge.

Internal work -Exposed on Wall

18.7.1 15 mm nominal outer dia pipes Rm 840 142.95 120,078.00






3 18.8 Providing and fixing CPVC pipes having thermal

stability for hot and cold water supply including all

CPVC plain and brass threaded fittings including

fixing the pipe with clamps at 1.00 mt spacing. this

includes jionting of pipes and fittings with one step

CPVC solvent cement and the cost of cutting

chases and making good the wall same including

testing of joints complete as per the direction of

engineer incharge

concealed work including cutting chases and

making good the wall etc.18.8.1 15 mm nominal outer dia pipes Rm 2439.2 246.20 600,531.04

18.8.2 20 mm nominal outer dia pipes Rm 583.2 284.85 166,124.52


18.8.4 32 mm nominal outer dia pipes Rm 390.8 412.90 161,361.32

4 DSR

Item

18.10

Providing and fixing G.I. pipes complete with GI

fittings and clamps including cutting and making

good the walls etc. (internal work) For roof level

18.10.

1

15 mm dia, nominal bore Rm 20

215.10 4,302.00

18.10.

2

20 mm dia, nominal bore

Rm 40

249.30

9,972.00

18.10.

3


304.15 30,415.00

18.10.

4


343.20 51,480.00

18.10.

5


425.65 53,206.25

18.10.

6


527.20 94,896.00

18.12.

7


524.25 82,307.25

5 DSR

Item

13.61

Painting with synthetic enamel paint of approved

drand and manufacture to give an even shade


S. NO. (DSR-

2016)


13.61.

1

Two more coast on new worksqm 222.6

78.40 17,451.84

6 18.17 Providing and fixing of gun metal gate valve with

CI wheel of approved quality (screwed ends)

18.17.

1

25mm dia, nominal boreEach 18

428.20 7,707.60

18.17.

2

32 mm dia, nominal boreEach 8

500.75 4,006.00

18.17.

3


584.70 3,508.20

18.17.

4


749.90 4,499.40

18.17.5 65mm nominal bore Each 5 1286.80 6,434.00

18.17.6 80mm nominal bore Each 1 1919.50 1,919.50

7 18.19 Providing and fixing gun metal non- return valve of

approved quality (PN 1.6)18.19.

6.2

80 nominal boreEach 4

2,944.55 11,778.20

8.0 18.16 Providing and fixing brass stop cock of approved

quality 18.16.

1

15mm nominal boreEach 102 260.00 26,520.00

18.16.

2

20mm nominal boreEach 164 280.00 45,920.00

9.0 10.2 Structual steel work welded in built up sections,

trusses and framed work including cutting,

hoisting, fixing in position and applying a priming

coat of approved steel primer all complete.kg 140 67.60 9,464.00

10.00 18.46 Providing and fixing G.I. union in G.I. pipe

including cutting and threading the pipe and

making long screws etc. complete (new work)18.46.

1


147.75 3,546.00

18.46.

2


170.95 3,760.90

18.46.

3


205.80 4,527.60

18.46.

4


240.65 5,294.30

18.46.

5


298.75 6,572.50

18.46.

6


384.90 8,467.80

11.00 18.49 Providing and fixing C.P. brass bib cock of

approved quality confirming to IS:893118.49.

1


371.70 37,913.40


S. NO. (DSR-

2016)


12 18.48 Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, ISI : 12701

marked, with cover and suitable locking

arrangement and making necessary holes for inlet,

outlet and overflow pipes but without fittings and

the base support for tank.

per

litre 22000

7.25

159,500.00

13 18.33.

1

Constructing masonry chamber 60x60x75 cm,

inside with 75 class designation brick work in

cement mortar 1:4 (1 cement:4 fine sand) for

sluice valve, with C.I. surface box 100mm, to

diameter, 160mm bottom diameter and 180mm

deep (inside) with chained lid and RCC top slab

1:2:4 mix (1 cement : 2 corase sand: 4 graded

stonr aggregate 20mm nominal size) necessary

excavation foundation concret 1:5:10 (1 cement:5

fine sand : 10 graded stone aggregate 40 mm

nominal size) and inside plastering with cement

mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick

finished with a floating coat of neat cement

complete as per standard design.

Each 14 6,849.60 95,894.40

14 16.7.1 BUTTERFLY VALVE (MANUAL) with C I body SS

Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure

rating for chilled water/hot eater circulation as

specifiedELECT.

DSR

2016 /

16.7.1.

6

65 nominal bore

Each 14 3,351.00 46,914.00

ELECT.

DSR

2016 /

16.7.1.

5

80 nominal bore

Each 20 3,719.00 74,380.00

ELECT.

DSR

2016 /

16.7.1.

4

100 nominal bore

Each 6 5,330.00 31,980.00

15 ELECT.

DSR

2016 /

14.13


(medium class) in ground complete with G.I.

fittings including trenching (75 cm deep) and re-

filling etc. as required

14.13.

2

80 mm dia, NBM 100 592.00 59,200.00

14.13.

3

100 mm dia, NBM 56 828.00 46,368.00

TOTAL 3,443,607.57

SUBHEAD-III (B) : WATER SUPPLY- INTERNAL WORK (NON-SCHEDULED ITEMS)


S. NO. (DSR-

2016)


16 M.R. Solar Water Heaters

Supply, erection, testing & commissioning of solar

water heating system with following details :

System temperature output : 60 degree C (during

clear sunny days)System type : Thermo syphon

System : Non Pressurised

Application : Bathing / Washing / Cooking

Type of Solar Collectors : Copper tube Flat Plate

Collectors as per BIS with following specifications -

Size of Collector : 2080 x 1070 x 100 mm

Number of Collector : To suit system requirement.

Absorber area : 2 sq M

Type : Cu - Cu

Weight : 46 Kg (Dry)

Absorber Coating : Selective - NALSUN

Absorbivity : > 0.95

Emissivity : < 0.2

Frame Material : 16 SWG extruded Aluminium

Glazing : Toughened Glass

Glass beeding : EPDM

Finish : Painted by approved shade

Hot water return pump

Hardware : SS 304

Electrical heating back up required

Insulation : PUF

Collector Stand : 35x35x3 mm MS angle

Hot Water Tank : Cylindrical - vertical / horizontal,

Stainless steel 304 grade with 100 mm thick Rock

Wool insulation including 22 SWG aluminium

cladding.

The entire system should be complete with

internal piping in G.I. (class B) with 50 mm rock

wool insulation of density 48 kg/m3 with 26

SWG Al cladding, necessary isolation valves, Y type

CI strainer, hardwares, temperature gauge of

range 0 - 120oC, water meter, MS angle iron

structure of min thickness 3 mm duly painted etc

as required to complete the system in all respects.

The entire system should be approved by BIS as

per IS : 12933 and as per local regulations.System Capacity : 4200 liters ( storage tank of

4200 litres ) per day (LPD) having 42 collectors.ITEM 1 1,134,554.00 1,134,554.00

System Capacity : 600 liters ( storage tank of 600

litres ) per day (LPD) having 6 collectors. ITEM 3 163,941.00 491,823.00


S. NO. (DSR-

2016)


17 MR Providing and fixing Double Faucet Storage type

Water Cooler ( Size 564 mm wide x 705 mm deep

x 1521 mm height, weight 88 kg) fully stainless

body having storage capacity of 150 ltrs, Cooling

Capacity of 150 Ltrs./hr., 2 nos of cold water outlet

with hermetic type compressor, gas cooled motor

equipped with over load protector, condensor for

propeller type, thermostat autometically

controlled temperature, refrigerent R -22, 230

volt, single phase 50 hertz, maximum current 6.8

amp including plug top and electrical lead wire

connection upto 3 metres from the cooler, water

inlet and drain out connections complete in all

respects of Voltas Model No 150/150 Tushar PSS

type or similar type of approved make.

Each 10 50,449.00 504,490.00

TOTAL 2,130,867.00

[1] EXTERNAL SEWERAGE SYSTEM

SEWERAGE NETWORK

1 Providing laying and jointing glazed stoneware

pipes grade ‘A’ with stiff mixture of cement mortar

in the proportion of 1:1 (1 cement : 1 fine sand)

including testing of joints etc. complete.

19.1.2 150 mm diameter metre 10.00 327.05 3,270.50


2 19.2 Providing and laying cement concrete 1:5:10 (1


aggregate 40 mm nominal size) alround SW pipes

including bed concrete as per standard design.



3 19.11 Constructing brick masonry circular manhole 1.22

m internal dia at bottom and 0.56 m dia at top in

cement mortar 1:4 (1 cement :4 coarse sand)

inside cement plaster 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand) finished

with a floating coat of neat cement foundation


graded stone aggregate 40 mm nominal size) and

making necessary channel in cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) finished with a

floating coat of neat cement, all complete as per

standard design :

SECTION - IV


S. NO. (DSR-

2016)


19.11.1 1.68 m deep with SFRC Cover and frame (heavy

duty HD-20 grade designation) 560 mm internal

diameter conforming to I.S. 12592, total weight of

cover and frame to be not less than 182 kg. fixed

in cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal

size) including centering, shuttering all complete.

(Excavation, foot rests and 12 mm thick cement

plaster at the external surface shall be paid for

separately) :

19.11.1.2With Sewer bricks conforming IS : 4885 each 2.00 16720.90 33,441.80

4 19.12 Extra depth for circular type manhole 1.22 m

internal dia (at bottom) beyond 1.68 m to 2.29 m :

19.12.2 With Sewer bricks conforming IS : 4885 metre 2.00 6505.15 13,010.30

5 Constructing brick masonry manhole with F.P.S.

bricks in cement mortar 1 : 4 (1 cement : 4 coarse

sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2

coarse sand : 4 grade stone aggregate 20mm

nominal size); foundation concrete 1:4:8 mix (1


aggregate 40 mm nominal size) inside plastering

12 mm thick with cement mortar 1:3 (1cement 3

coarse sand ) finished with a floating coat of neat

cement and making channels in cement concrete

1:2:4 (1cement : 2 coarse sand: 4 graded stone

aggregate 20 mm nominal size) finishd with a

floating coat of neat cement complete as per

standard design

19.7.1.

1

Inside size 90 x 80 cm & 45 cm deep including CI

cover with frame (light duty) 455 x 610mm

internal dimension total wt. of cover & frame to

be not less than 38 kg (wt. of cover 23 kg and wt.

of frame 15 kg)each 45.00 8,634.10 388,534.50

6 Extra for depth for manhole with F.P.S. bricks

19.8.1.1size 90 X 80 cm m 18.00 5,718.60 102,934.80

7 19.15 Providing M.S. foot rests including fixing in

manholes with 20x20x10 cm cement concrete

blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 20 mm nominal size) as per

standard design19.15.

1

With 20x20 mm square barEach 25.00 267.95 6,698.75

8 7087 Providing and fixing C.I. tee 150mm at the inlet

and outlet of septic tank. Each 3.00 600.00 1,800.00

9 17.35 Providing and fixing soil, waste and vent pipes :


S. NO. (DSR-

2016)


17.35.

2.1

Providing & fixing 75mm dia vent pipes.Rm. 20.00 712.20 14,244.00

10 17.56 Providing and fixing terminal guard :

17.56.

2.1

Providing & fixing of 75mm dia cast iron terminal

guard. Each 3.00 197.10 591.30

11 19.19 Providing and fixing in position precast RCC

manhole cover and frame of required shape and

approved quality.19.19.

2.2

M.D. -10- Circular shape 500mm internal diameterEach 3.00 908.35 2,725.05

12 19.16 Providing orange colour safety foot rest of

minimum 6 mm thick plastic encapsulated as per

IS : 10910, on 12 mm dia steel bar conforming to

IS : 1786, having minimum cross section as 23

mmx25 mm and over all minimum length 263 mm

and width as 165 mm with minimum 112 mm

space between protruded legs having 2 mm tread

on top surface by ribbing or chequering besides

necessary and adequate anchoring projections on

tail length on 138 mm as per standard drawing

and suitable to with stand the bend test and

chemical resistance test as per specifications and

having manufacture's permanent identification

mark to be visible even after fixing, including fixing

in manholes with 30x20x15 cm cement concrete

block 1:3:6 (1 cement : 3 coarse sand : 6 graded

stone aggregate 20 mm nominal size) complete as

per design.

each 22.00 311.60 6,855.20

13 Providing and fixing square mouth SW gully trap

grade ‘A’ complete CI grating brick masonry

chamber with bricks of class designation 75 and

water tight CI cover with frame of 300 x 300 mm

size (inside) the weight of cover to be not less than

13.00 kg and frame to be not less than 5 kg. as per

standard design. (COVER MIN. 4.5 KG & FRAME

MIN.2.7 KG )

19.4.3.1180x150 mm size P type With FPS bricks each 31.00 1664.80 51,608.80

14 19.32 Making soak pit 2.5 m diameter 3.0 metre deep

with 45 x 45 cm dry brick honey comb shaft with

bricks of class designation 75 and S.W. drain pipe

100 mm diameter, 1.8m long complete as per

standard design.19.32.

1

With F.P.S. bricksEach 2.00 20,681.55 41,363.10


S. NO. (DSR-

2016)


15 19.21.

1

Making connection of drain or sewer line with

existing manhole including breaking into and

making good the walls, floors with cement cincrete

1:2:4 mix (1cement: 2 coarse sand : 4 graded stone

aggregate 20mm nominal size) cement plastered

on both sides with cement mortar 1:3 (1cement : 3

coarse sand) finished with a floating coat of neat

cement and making necessary channels for the

drain etc. complete for pipes 100 to 230mm dia.Item 1.00 364.60 364.60

TOTAL 1,677,159.45

[2] EXTERNAL DRAINAGE SYSTEM

DRAINAGE NETWORK

1 19.6 Providing and laying non-pressure NP2 class (light

duty) RCC pipes with collars jointed with stiff

mixture of cement mortar in the proportion of 1:2

(1 cement : 2 fine sand) including testing of joints

etc. complete. (for storm drainage)

19.6.2 150 mm dia RCC pipe Meter 95.00 356.70 33,886.50




19.6.7 600 mm dia RCC pipe Meter 5.00 1,397.10 6,985.50

2 Constructing brick masonry road gully chamber

50x45x60 cm with bricks of class designation 75 in

cement mortar 1:5 (1 cement : 5 fine sand)

including 500 x 450 mm (heavy duty) precast RCC

horizontal grating with frame complete as per

standard design:19.27.

1

with FPS bricksEach 42.00 4,043.10 169,810.20

3 19.1 Providing, laying and jointing glazed stoneware

pipes grade 'A' with stiff mixture of cement mortar

in the proportion of 1:1 (1 cement: 1 fine sand)

including testing of joints etc. complete:

19.1.3 200 mm diameter R.M. 12.00 423.35 5,080.20

4 23.7 Supplying, filling, spreading & leveling coarse sand

of size range 1.5 mm to 2 mm in recharge pit, in

required thickness over gravel layer, for all leads &

lifts, all complete as per direction of Engineer –in-

charge. Cu.M 3.54 1038.05 3,674.70

5 19.19 Providing and fixing in position pre-cast R.C.C.

manhole cover and frame of required shape and

approved quality19.19.1 L D- 2.5

19.19.1.1Rectangular shape 600x450mm internal

dimensions Each 8.00 1,073.05 8,584.40

SECTION - V


S. NO. (DSR-

2016)


6 23.1 Boring/drilling bore well of required dia for

Casing/ strainer pipe, by suitable method

prescribed in IS: 2800 (part I), including collecting

samples from different strata, preparing and

submitting strata chart/bore log, including hire &

running charges of all equipments, tools, plants &

machineries required for the job, all complete as

per direction of Engineer –in-charge, upto 90

metre depth below ground level.

23.1.1 All types of soil

23.1.1.1300 mm dia. R.M. 40.00 370.70 14,828.00

7 23..3 Supplying, assembling, lowering and fixing in

vertical position in bore well, unplasticized PVC

medium well casing (CM) pipe of required dia,

conforming to IS: 12818, including required hire

and labour charges, fittings & accessories etc. all

complete, for all depths, as per direction of

Engineer –in-charge.23.3.2 150 mm nominal size dia. R.M. 50.00 572.30 28,615.00

8 23.6 Supplying, filling, spreading & leveling gravels of

size range 4.6 mm to 4.8 mm, in the recharge pit,

over the existing layer of boulders, in required

thickness, for all leads & lifts, all complete as per

direction of Engineer-in-charge.Cu.M 9.80 1038.05 10,172.89

9 23.5 Supplying, filling, spreading & leveling stone

boulders of size range 5 cm to 20 cm, in recharge

pit, in the required thickness, for all leads & lifts,

all complete as per direction of Engineer-in-

charge. Cu.M 9.80 921.90 9,034.62

TOTAL 526,327.76

CIVIL WORKS

1 2.6 Earth work In excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30cm in depth. 1.5m in width as per as

10 sq.m on plan) including disposal of excavated

earth, lead up to 50m and lift up to 1.5m, disposed

earth to be levelled and neatly dressed.

2.6.1 All kinds of soil Cu.M 106.80 125.95 13,451.46

2 2.6.1&

2.26

In all kind of soil upto 1.5m to 3.0m. depthCum 66.01 177.70 11,729.41

3 2.25 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers

not exceeding 20cm in depth, consolidating Each

deposited layer by ramming and watering , lead up

to 50 m and lift up to 1.5m. Cu.M 62.50 125.75 7,859.38

SECTION- VI


S. NO. (DSR-

2016)


4 2.26 Extra for every additional lift of 1.5 m or part there

of in:(a) Depth exe. 1.5m but not exceeding 3.0m. Cu.M 52.50 51.75 2,716.88

(b) Depth exe. 3.0m but not exceeding 4.5m. Cu.M 30.10 51.75 1,557.68

5 4.1 Providing and laying in position cement cncrete of

specified grade excluding the cost of centring and

shuttering - all work upto plinth level.

4.1.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) Cum 15.00 5,481.95 82,229.25

4.1.8 1:4:8 (1 cement :4 coarse sand : 8 graded stone

aggregate 40 mm nominal size) Cu.M 2.40 4,478.15 10,747.56

4.1.10 1:5:10 (1 cement : 5 coarse sand : 10 graded ston

aggregate 40 mm nominal size) CUM 133.75 4,209.05 562,960.44

6.00 2.10 Excavating trenches of required width for pipes,

cables etc. including excavation for sockets and

dressing of sides, ramming of bottom depth upto

1.5 M including getting out the excavated soil

(HARD OR SOFT) and then returning the soil as

required in layers not exceeding 20 cms in depth

including consolidating each deposited layer by

ramming, watering etc. and disposing of surplus

excavated soil as directed within a lead of 50m.

[hard/Dense soil]

2.10.1 All kind of soil

2.10.1.2Pipes,cables etc.exceeding 80mm dia.but not

exceeding 300mm dia. Mtr. 1331.00 225.45 300,073.95

7.00 DSR 2.11Extra for excavating trenches for pipes, cables etc.

in all kinds of soil for depth exceeding 1.5m,but

not exceeding 3 m.(Rate is over corresponding

basic item for depth up to 1.5 metre).Mtr. 89.50 324.42 29,035.59

8 5.3 Reinforced cement concrete work in slab with

1:2:4 (1 cement : 2 course sand : 4 graded stone

aggregate 20mm normal size). Cum 12.00 7,390.80 88,689.60

9 5.9 Centring and shuttering including strutting,

proppintg etc. and removal of form for:5.9.3 Suspended floors,roofs, landings, balconies and

access platform. Sq.M 83.50 422.30 35,262.05

10 5.9.16 Edges of slabs and breaks in floors and walls, 0.00

5.9.16.1Under 20 cm wide R.M. 37.12 122.20 4,536.06

11 5.22 Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

and binding all complete upto plinth level.

5.22.6 Thermo Mechanically Treated bars. Kg. 1296.10 56.60 73,359.26


S. NO. (DSR-

2016)


12 5.33 Providing and laying in position machine batched

and machine mixed design mix M-25 grade

cement concrete for reinforced cement concrete

work, using cement content as per approved

design mix, including pumping of concrete to site

of laying but excluding the cost of centering,

shuttering, finishing and reinforcement, including

admixtures in recommended proportions as per IS:

9103 to accelerate, retard setting of concrete,

improve workability without impairing strength

and durability as per direction of Engineer-in-

charge.

(Note :- Cement content considered in this item is

@ 330 kg/cum. Excess/less cement used as per

design mix is payable/recoverable separately).

5.33.1 All works upto plinth level. Cu.M 7.56 6,446.45 48,735.16

13 6.1 Brick work with F.P.S. bricks of class designation

75 in foundation and plinth in:6.1.1 Cement mortar 1:4 (1 cement: 4 coarse sand) Cu.M 58.80 4,970.30 292,253.64

14 13.1.1 12 mm thick cement plaster of mix 1:4 (1 cement :

4 fine sand). Cum 90.00 172.95 15,565.50

15 13.5 15 mm cement plaster on rough side of single or

half brick wall of mix13.5.1. 1:4 (1 cement: 4 coarse sand)

Sqm 150.00 209.65 31,447.50

16 2.8 Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5m

in width or 10 Sq.M on plan) including dressing of

sides and ramming ob bottoms, lift upto 1.5m,

including getting out the excavated soil and

disposal of surplus excavated soil as directed,

withen a lead of 50m.

2.8.1 All kinds of soil Cu.M 118.34 166.40 19,691.78

17 9.50 Providing and fixing hard drawn steel wire fabric

75x25 mm mesh of weight not less than 7.75 Kg

per sqm to window frames etc. including 62x19

mm beading of second class teak wood and

priming coat with approved steel primer all

complete. Sq.M 18.84 1,054.00 19,857.36

TOTAL 1,651,759.49

EXTERNAL WATER SUPPLY SYSTEM

DISTRIBUTION NETWORK FOR FRESH WATER

SUPPLY(D.S.R. 2016 ITEMS)

SECTION- VII


S. NO. (DSR-

2016)


1 18.12 Providing and fixing G.I. pipes complete with G.I.

fittings including ,trenching and refilling etc.

external works

18.12.1 15mm nominal bore RM 20 160.20 3,204.00

18.12.2 20mm nominal bore RM 20 186.30 3,726.00 18.12.6 50mm nominal bore RM 550 342.70 188,485.00



2.00 DSR

Item

18.40

Painting GI pipes and fittings with two coats of anti

corrosive bitumastic paint of approved quality

18.40.

1


6.00 120.00

18.40.

2


7.10 142.00

18.40.

6


14.80 8,140.00

18.40.

7


18.25 1,186.25

3.0 Providing and filling sand of grading zone V or

coarser grade all-round the G.I. pipes in external

work.18.41.1 15mm nominal bore RM 20 66.80 1,336.00





18.41.9 100 mm nominal bore RM 30 129.10 3,873.00

18.41.10150 mm nominal bore RM 0 192.30 -

4.0

18.59

Providing and fixing C.I. double acting air valve of

approved quality with bolts, nuts, rubber

insertions etc. complete (The tail pieces, tapers etc

if required will be paid separately) :

18.59.

1

50 mm diaEach 4 4662.45 18,649.80

18.59.

2

80 mm diaEach 1 5649.75 5,649.75

18.59.

3

100 mm diaEach 1 7410.80 7,410.80

5.0 18.31.1 Providing & Fixing C.I.sluice valve(with cap)

complete with bolts,nuts,rubber insertions etc.(the

tail pieces if required will be paid separately)

18.31.1.

1100 mm dia.pipe

Each 3 3317.55 9,952.65 18.31.3.

1150 mm dia.pipe

Each 0 4881.25 -


S. NO. (DSR-

2016)


6.0 18.32.

1

Constructing masonry chamber 30x30x50

cm,inside with 75 class designation brick work in

cement mortar 1:4 (1 cement:4 coarce sand) for

stop cock complete with C.I. surface box

100x100x75mm (inside) with locking arrangement

and RCC top slab 1:2:4 mix (1 cement : 2 corase

sand: 4 graded stonr aggregate 20mm nominal

size) necessary excavation foundation concret

1:5:10 (1 cement:5 fine sand : 10 graded stone

aggregate 40 mm nominal size) and inside

plastering with cement mortor 1:3 (1 cement : 3

coarse sand) 12 mm thick finished with a floating

coat of neat cement complete as per standard

design.Each 10 1,195.35 11,953.50

7.00 18.13.

2

Making connection of GI distribution branch with

GI main of 50-80mm nominal bore by providing

and fixing tee, including cutting and threading the

pipe etc. complete. Item 4 771.20 3,084.80

8.00 Providing & fixing of Garden hydrant outlet

consisting 1 No. 20mm dia. Ball valve, Bib cock

(Brass) for connecting rubber hose, pipes &

fittings including brick masonary chamber

300x300x500mm.18.15 Bib Cock - 20mm 280.40 -

18.18 Ball Valve - 20mm 327.05 -

TOTAL Each 8 607.45 4,859.60

9.00

16.7.3

NON - RETURN VALVE with duel plate of C I body

SS plates vulcanized NBR seal flanged end & PN 16

pressure rating for chilled / hot water circulation

including insulation as specified.

ELECT.

DSR

2014 /

16.7.3.

4

100 nominal bore

Each

4 3,893.00

15,572.00

ELECT.

DSR

2014 /

16.7.3.

5

80 nominal bore

Each

8 2,811.00

22,488.00

10.00 17.30 Providing and fixing in position 25 mm diameter

mosquito proof coupling of approved municipal

design. Each

6 38.50

231.00

TOTAL 424,600.65

PUMPS( NON SCHEDULED ITEMS)

1 Mr Raw Water Treatment Feed Pump set Set 1 327,267.00 327,267.00

SECTION- VIII


S. NO. (DSR-

2016)


Providing, fixing, commissioing and testing

package vertical raw water pumps, comprising of

Electrical Driven inline pumping with all

accessories, Pumps shall be with C.I. Base, S.S 304,

impeller, shaft, mechanical seal, S.S. Shaft directly

coupled to motor suitable for operation on

400/440 volts, 3 phase 2900 RPM. TEFC electronic

motor mounted on a common channel baseplate

150mm dia pressure gauge, GM isolation cock and

cement concrete foundation with plaster with

dunlop cushy foot mountings with all accessories

such as NRVs, valves, pressure guage bourden

type, common suction and delivery header,

bellows on sucton and delivery side complete in all

repsects.

Pumps shall be suitable for 415 ± 10% volts 3

phase 50 Hz A.C supply & shall be having the

following requirement complete with foundation

and associated civil works.Suction & Delivery Header - SS 304

Control Valve On suction and Delivery - Ball Valve

Only (No Butterfly Valve Accepted).Flow Prevention - Only Check Valve

Suction & delivery header including all pipes,

suction & delivery sides valves, NRV, Pressure

gauges & accessories complete. Flow Rate : 7.0 LPS (1 working + 1 stand by)

Head : 35 M

Min. Motor HP : 7.5 H.P. (Each)

2 Mr Water Booster Pumpset (Treated Water Supply)Set 1 897,345.00 897,345.00

Supplying & supervision of testing &

commissioning of Booster Pumpset

(Hydropneumatic systems) as described belowSupplying & supervision of testing &

commissioning of package vertical

Hydropneumatic system, comprising of 2.0 nos. (1

duty + 1 stand by) Electrical Driven inline pumping

sets each of 7.0 LPS to a head to 80 meter with

all accessories, Pumps shall be with C.I. Base, S.S

304, impeller, shaft, mechanical seal, S.S. Shaft

directly coupled to motor suitable for operation on

400/440 volts, 3 phase 2900 RPM. TEFC electronic

motor mounted on a common channel baseplate

150mm dia pressure gauge, GM isolation cock and

cement concrete foundation with plaster with

dunlop cushy foot mountings with all accessories

such as NRVs, valves, pressure switch, common

suction and delivery header, bellows on sucton

and delivery side complete in all repsects.


S. NO. (DSR-

2016)


Pump mounted or wall mounted microprocessor

based controller, Electronic control panel with

frequency inverter, logic controller relays, pressure

sensor, pressure sensor transmitter, electrical

wiring, cabling from panel to pumps, level

controller, two lined LCD display, diodes to

indicate pump ready, pump running and fault

capable to communicate with toher RS 485

interface. with Power box equipped with fuses or

isolators or circuit breakers as required. complete

with all accessories as per manufacturer

specifications.

Suction & Delivery Header - SS 304

Control Valve On suction and Delivery - Ball Valve

Only (No Butterfly Valve Accepted).Flow Prevention - Only Check Valve

One Number Variable frequency Drive

Impeller : Stainless Steel

Shaft : Stainless Steel

RPM : 2900.

Mover : Electric Motor

HP - As required.

Necessary foundation with bolts

Ball valve on suction & delivery

NRV on delivery

Dust & vermin proof cubicle type motor control

centre fabricated from powder coated 16 SWG MS

sheet suitable to automatic working of above

mentioned pumps.


S. NO. (DSR-

2016)


3 Mr Sump Pumps

Supply & Installation, testing and commissioning

of centrifugal non clogging submersible sump

pumps for plant room drainage. Pump capable

capable of handling 25 mm dia soft solids. Motor

suitable for 415 + 10% volts, 3 phase, 50 Hz AC

Power supply. Pumps shall be suitable for

automatic/manual operation (Overall depth of

sump – 1.5 M). Submersible sump pump shall be

provided with dry running protection. Inclusive of

supporting arrangement for stationary type.

Two nos. of pump installed in one sump pit 1

working & 1 standby with automatic/manual

opration as requireds.

Waste Water Drainage Sump Pump (PLANT

ROOM) Each 2 68,621.00 137,242.00

Flow rate : 2 LPS

Head : 10 Mtrs.

Min. Motor HP : 2.0 (Each)

4 Mr Supply & installation, testing & commissioning of

sand filter having FRP pressure vessel suitable for

test pressure of 7 Kg. / cm2 including valves for

back-wash arrangement complete with initial

charge of media to remove the total suspended

particles from the water.

Capacity : 7.0 LPS

Working Pressure : (5 ± 2.5)MWC Each 1 269,204.00 269,204.00

5 Mr Supplying, storing, handling, installation, testing &

commissioning of Activated Carbon Filter having

FRP pressure vessel suitable for test pressure of 7

Kg./cm2 including valves for back-wash

arrangement complete with initial charge of media

to remove the total suspended particles from the

water. Capacity : 7.0 LPS


6 Mr Supplying, storing, handling, installation, testing &

commissioning of water softening system having

FRP pressure vessel suitable for test pressure of 7

Kg/cm2 including dished end, ion- exchange resin,

Frontal piping, C.I. diaphragm type valve, brine

injection assembly for regeneration of softener,

brine measuring cum salt water tank, inter

connected flexible polypropylene MS Rubber lined

(MSRL) piping, valves including provision of bye-

pass arrangement complete with inside and

outside painting etc. as required.

Receiving, storing, handling and fixing of

PVC/HDPE/FRP tank for Brine solution along with

Hydraulic Injector with control valve and piping

for brine injection. Capacity : 7.0 LPS


S. NO. (DSR-

2016)



7 Mr Supplying and fixing of PVC/HDPE/FRP tank

including electrical operated metering/dosing

pump for dosing of alum/sodium hypo-chlorite

solutions in pipeline (all contacting parts shall be

of stainless steel). Capacity - 0-12 LPH Each 1 34,839.00 34,839.00

8 Mr Supplying & fixing of float based visual flow meter

(Rotameter) suitable for water flow rate of 25200

litres per hour in the input line of water softener

including matching flanges, nuts, bolts and 3 mm

thick rubber insertions/gaskets complete. to

assess the water flow rate in water softener.Each 1 23,460.00 23,460.00

TOTAL 2,428,348.00

ELECTRICAL WORKS (NON SCHEDULED ITEMS)

1 MR CUBICAL PANEL BOARD - PLUMBING PH Item 1 250,728.75 250,728.75

i) For 2 x 7.5 HP Filter Feed Pumps (1 duty + 1

stand by) ii) For 2 x 18.0 HP Treated Water Transfer Pumps

Set (1 Duty + 1 Stand by) - (only isolator).

iii) For 2 x 2.0 HP Waste Sump Pumps pump room

(1 Duty + 1 Stand by) - (only isolator). - Pump room

iv) For 3 x 3.7 HP Bore well Pump (only isolator).

Supply, installation, testing and commissioning of

Cubical type sectionalised floor standing switch

board of 31 MVA fault capacity at 415 V complete

with 3.5 strip, 160 A capacity Aluminium Bus - Bar

Electrolytic grade, cable alley, switchgears of

following capacity & as per specifications.

A) INCOMER

100 A TP MCCB with heavy duty solid neutral link

with (0-100A) ammeter with 3 CT and selector

switch, (0 - 500 V) voltmeter with selector switch,

phase indication light with protection fuse. - 01

Set

B) OUTGOINGS

i) For 2 x 7.5 HP Filter Feed Pumps

12 A TP MCB with 10 A DOL starter, overload

relay, 96 mm (0-25A) ammeter with single CT,

start / stop push buttons, on / off / trip indication

lights with protection fuse, single phase preventer.

- 01 set.

ii) For 2 x 18.0 HP Treated Water Transfer Pumps

(H.S)40.0 A TP MCB with isolator

SECTION- IX


S. NO. (DSR-

2016)


iii) For 2 x 2.0 HP Waste Water Transfer Pumps -

only feeder to sub panels.12 A TP MCB with 10 A DOL starter, overload

relay, 96 mm (0-25A) ammeter with single CT,

start / stop push buttons, on / off / trip indication

lights with protection fuse, single phase preventer.

- 01 set.iv) For 3.0 No. - 3.7 HP Borewell Pump

32 A TP MCB with isolator

NOTE :

i) All the drainage pumps shall be work cyclic

process i.e. in first operation duty pump work on

duty and stand by pump duty pump work on stand

by and stand by pump work as duty pump.

ii) The drainage Stand by pumps automatically

work as drainage assist pump for Duty pump when

level of water rises in drainage sump pumps i.e.

Both pumps can work at a time & operation shall

be controlled with the help of level controllers and

float switches.

TOTAL 250,728.75

2 POWER & CONTROL CABLING (DSR 2016

SCHEDULED ITEMS)

2.1

DSR

5.3

Supplying and Earthing with GI earth plate 600mm

x 600 mm x 6mm thick including accessories and

providing masonary enclosure with cover plate

having locking arrangement and watering pipe

etc, with coke and salt ) as required.

Set 2.0 3,583.00 7,166.00

2.2

5.11

Supplying and laying 25 mm x 5 mm. G.I. strip in

40 mm dia. G.I. Pipe from earth electrode, as

required.

Rm 40.0 351.00 14,040.00

2.3

5.15

Providing & fixing 25mm x 5mm G.I. strip on

surface or in recess for connections etc. as

required. Rm 200.0 129.00 25,800.00

2.3.1

5.18

Providing and Fixing 6 SWG dia G.I. wire on surface

or in recess for loop earthing alongwith existing

surface/ recessed conduit/ submain wiring/ cable

as required.

Rm 300.0 23.00 6,900.00

2.3.2

4.1

Supplying, fabricating and installing following size

of perforated M.S. cable trays, including horizontal

and vertical bends, reducers, tees, cross members

and other accessories as required and duly

suspended from the ceiling with M.S. suspenders

and including paint

4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Rm 40.0 348.00 13,920.00

2.44.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Rm 30.0 526.00 15,780.00


S. NO. (DSR-

2016)


2.4.1

7.7.1

Laying and fixing of One number PVC Insulated

and PVC Sheathed/XLPE power cable of 1.1 kV

grade of size not exceeding 25 sqmm on surface as

required. RM 25.0 25.00 625.00

7.7.3

Laying and fixing of One number PVC Insulated

and PVC Sheathed/XLPE power cable of 1.1 kV

grade of size exceeding 25 sqmm but not

exceeding 120 sqmm on surface as required.

RM 240.0 84.00 20,160.00

Supplying of all materials and making terminations

of 1.1 KV grade aluminium multicore cables of the

following sizes. The work includes cable glanding

using brass plated double compression glands,

sizing the core leads, removing insulation, fixing

suitable crimping type copper lugs/ thimbles by

using hydraulic crimping tools with correct size of

the dies, shaping the leads and neatly connecting

the same to the equipment terminals.

9.1.25 3.5 Core 120 sq. mm. Armoured Aluminium cable. Nos 10.0 500.00 5,000.00

2.59.1.21 3.5 Core 35 sq. mm. Armoured Aluminium cable. Nos 80.0 282.00 22,560.00

Control Cabling ( PVC insulated and PVC sheathed,

armoured, Copper Conductor of 1.1 KV grade on

existing cable trays).

MR 5C x 1.5 Sq. mm RM 150.0 160.00 24,000.00

TOTAL 155,951.00

TECHNOLOGY - SBR (120+25 = 145 KLD)

Technology

A EFFLUENT TREATMENT PLANT - 25 KLD

Design, Supplying, Installing, Testing &

Commissioning of Effluent Treatment Plant of

Capacity 25 KLD. The plant proposed shall be with

a common pump room. The plant is proposed to

be installed in the basement accessible from the

pump room itself for future maintenance. No

opening shall be provided on main slab above for

this purpos. :All the equipment, piping, pumps, air blowers and

electrical panel to be housed in the skid including

inlet, outlet, overflow, vent, moving ladders &

railing. The Plant shall be completed with a

central Electrical Power and Control panel fully

pre/site wired and with all power and control

cables to all pumps and equipment including all

instrumentation, level and other controls. The cost

will also include any consequential civil work

including making only foundations for the pumps,

blowers etc.

SECTION - X


S. NO. (DSR-

2016)


Effluent from OT Scrubs, blood bank, labs etc.

Some solvent/ chemical waste originating typically

from hospital complex shall also be discharged

into the ETP. Design to take consideration of same.

Anticipated effluent parameters before treatment:

Daily average flow : 25 cubm/Day

PH : 5.5 - 9.0

BOD5 : 250 - 600 mg/l

S. Solids : 200 - 650 Mg/l

COD : 600 - 1200 mg/l

Desired Effluent discharge standard after teritary

treatment: PH : 7.0 - 8.5

BOD5 : Less than 100 mg/l

S. Solids : Less than 100 mg/l

COD : Less than 250 mg/l

Effluent treatment plant shall include the

following items:- Bar Screen Chamber

- Equalization tank/sump - RCC Construction

- Flocculation Tank - FRP Construction

- Tube Settler - RCC Construction

- Lime/alum/polyelectrolyte dosing

- Equity pumps/ Sludge recirculation pumps

- Piping, valves etc

( All RCC / brick work shall be in Civil Contractor's

scope)Note: ETP contactor has to provide necessary

details regarding the above said works. All the

structural work shall be subject to the appoval of

structural consultants.

1.0 Shop Drawings.

Detailed GA drawing, flow diagram, equipment

list, power load requirement with design

calculations of all elements of the plant, electrical

and mechanical work to satisfy / supply adequacy

of design followed by submission of detailed

GOOD FOR CONSTRUCTION' architectural,

structural, construction, electrical, mechanical and

piping drawing for approval.

Contractor shall ensure submission of detailed GA

drawings (Plan & Section), P & I diagram,

schematic diagram for the above mentioned

components and additional components such as

inserts, puddle flanges, vent pipes etc. if so

required for the complete work.


S. NO. (DSR-

2016)


2.0 Supply, installation, testing & commissioning of 2

Nos Stainless Steel Perforated Screen with

suitable lifting arrangement(size 400 x 500 mm

high approx). Required perforation of 10 mm and

8 mm respectively. - Jash / Ecologix / HydroconSet 1 25000 25000

3.0 Supply, installation, testing & commissioning of

level controllers & indicators for automatic

operation of the complete system. - Pune Techtrol

/ Equivalent Lot 1 30000 30000

4.0 Providing, fixing, testing & commissioning of

Horizontal self priming, non-clog type effluent

handling pumps capable of handling solids upto 7-

10mm for incoming effluent from equalization

tank to Coagulation tanks and by pass the effluent

to municipal sewer in the time of maintenance .

The pump shall have CI casing & SS shaft & bronze

impeller, TEFC induction motor including pressure

gauge, all necessary piping (Inlet & outlet pipe),

suction & delivery header valves, level controller

with wiring to control the level of sump

automatically. etc. Receiving tanks shall be

completed with inlet, outlet, drain arrangement

(Pipe + Valve).

Equalized Effluent Water Lifting Pumps : DP /

Ebara / ITT(2 Nos. - 1 W +1 S)

Flow rate (each pump) - 10 m3 / hr

Head - 8-10 Mtr

Solid Handling - 7- 10mm Set 1 55000 55000

5.0 Providing, fixing, testing & commissioning of non

clog type centrifugal semi open impeller type

pumps for sludge lifting 2 nos. (1W+1S) for the

disposal of sludge from settling tank to sludge

holding tank. The pumps shall have CI casing, CI

Impeller, CS shaft & sleeve with mechanical rotary

shaft seal connected by a flexible tier type

coupling to TEFC induction motor mounted on a

common channel base-plate with coupling guard,

150 mm dia pressure gauge with GM isolation

cock. Motor to be suitable for 415 + 10% volt, for 3

phase, 50 cycle AC supply including all necessary

piping, valves and other accessories complete as

required.

Sludge Transfer pump - Kirloskar / Matter and

Plat / Johnson(2 Nos. - 1 W +1 S)

Flow Rate (each pump) - 10 m3 / hr

Head - 12 Mtr

Solid Handling - 7-10 mm

Type of Pump - Centrifugal Sludge transfer pumpNo 1 115,000.00 115000


S. NO. (DSR-

2016)



lime/alum/polyelectrolyte dosing system

consisting of one HDPE tank of 100 liters capacity

with a positive displacement diaphragm dosing

pump having variable flow rate of (0-6 LPH). The

motor shall be suitable for operation at 240V/

single phase/50 Hertz supply. The pump shall be

supplied complete with necessary polypropylene

piping, valves, strainers & injection fittings for

complete automatic dosing. - Asia LMI /

Toshiniwal / NivoEach 3 140,000.00 420000

7.0 Supplying, installing, testing and commissioning of

high speed Agitator of SS 304for floculation

complete with single phase motor for flash mixer. -

Hydrocon / Remi Set 1 55,000.00 55000


Flash mixer cum Flocculation tank in MSFRP

construction complete with puddle flange,

inlet/outlet connections etc - Hydrocon / RemiSet 1 55,000.00 55000

9.0 Interconnectiong Pipelines, valves & fittings for

hospital waste water pretreatment. - Jindal / TataJob 1 55,000.00 55000

A SEWAGE TREATMENT PLANT AND ETP - 120 KLD

Design, Supplying, Installing, Testing &

Commissioning of Sewage Treatment Plant based

on SBR technology with Capacity 120 KLD & 25

KLD ETP . The plant proposed shall be with a

common pump room. The plant is proposed to be

installed in the basement accessible from the

pump room itself for future maintenance. No

opening shall be provided on main slab above for

this purpos. :All the equipment, piping, pumps, air blowers and

electrical panel to be housed in the skid including

inlet, outlet, overflow, vent, moving ladders &

railing. The Plant shall be completed with a

central Electrical Power and Control panel fully

pre/site wired and with all power and control

cables to all pumps and equipment including all

instrumentation, level and other controls. The cost

will also include any consequential civil work

including making foundations for the pumps,

blowers etc.

1.0 Shop Drawings.


S. NO. (DSR-

2016)


Detailed GA drawing, flow diagram, equipment

list, power load requirement with design

calculations of all elements of the plant, electrical

and mechanical work to satisfy / supply adequacy

of design followed by submission of detailed

GOOD FOR CONSTRUCTION' architectural,

structural, construction, electrical, mechanical and

piping drawing for approval.

Contractor shall ensure submission of detailed GA

drawings (Plan & Section), P & I diagram,

schematic diagram for the above mentioned

components and additional components such as

inserts, puddle flanges, vent pipes etc. if so

required for the complete work.

Nature of Waste - Domestic Sewage/Laundry

waste/Kitchen waste Water/Filter Backwash/

Cleaning

Daily average flow - -120 cum/day

Anticipated effluent parameters before treatment:

PH - 7.5-8.5

BOD5 - 300 mg/ltr

COD - 500 mg/ltr.

SS - 300 mg/ltr.

Oil & Grease - 150 mg/ltr

Ecoli - >106 MPN

Ammonical Nitrogen - 50 ppm

Desired treated sewage standard after teritary

treatment:PH - 6.5 – 8.0

BOD5 - Less than 10 Mg/L

COD - Less than 50 Mg/L

S. Solids - Less than 10 Mg/L

Hardness - Less than 5 ppm

Oil & Grease - < 10 Mg/L

Ecoli - < 103 MPN

Chlorine dosing - 0.5 ppm

Ammonical Nitrogen - 5 ppm

Sewage treatment plant shall include the following

items:- Bar Screen Chamber

- Oil & Grease chamber

- Sewage equalization tank/sump

- SBR Reactor

- Chlorine Contact Tank

- Sludge Holding Tank

- Filtration through MGF & ACF

- Softener

UV

- UF for Flushing Water Demand Only

- Treated / Soft Water Tank

- Air Blowers, Pumps & equipment


S. NO. (DSR-

2016)


- Centrifuge

- Piping, valves etc

- Electrical Panel & Cabling

Note: STP contactor has to provide necessary

details regarding the abovesaid works. All the

structural work shall be subject to the appoval of

structural consultants.

1.0 Supply & fixing of MS hot dip galvanized puddle

flanges in accordance to BS:10 table D as required

to be provided (in the structural slab and wall) of

various diameters. Puddle flanges shall be

provided for all the structural component of the

STP. The installation of the puddle flanges shall be

carried out by the Civil contractor in accordance

with Civil GA drawing (to be prepared by the STP

contractor) at the required levels & position;

under the supervision of the STP contractor.Job 1 40000 40000

2.0 Supply & fixing of plastic manhole step/foot rest

(@ 300 mm c/C) with polypropelene compound

injection molded around 12 mm dia (Fe-415) steel

reinforcing bar. Provision of the foot rest is

envisaged in various tanks/ components of the STP

for the purpose of accessability. The installation of

the foot rest shall be done by the civil contractor

as per civil GA drawing.Job 1 24550 24550

3.0 Supply & fixing of DI Medium duty rectangular

manhole cover with frame for the feasibility of

access in the tanksSize 600x 900 Nos. 1 15000 15000

Size 600x 600 Nos. 1 10000 10000

4.0 Supply & fixing of vent pipes of 150 mm dia with

mosquito proof grating suitable for the ventilation

purpose of the various tanks. Nos. 1 15000 15000

5.0 Supply & fixing of DI grating for drain covers of

300X600mm sizing. Nos. 1 30000 30000

6.0 Providing and fixing manually cleaned Bar Screens,

to remove coarse and fine material in the waste

water made up of SS complete as required

including handle for lifting. Civil construction of

bar screen chamber by cilvil contractor as per

design submitted by STP vendor. - Hydrocon /

Jash / Ecologix6.1 Coarse Screen (for 0.6 m/s inlet velocity and 0.9

m/s outlet velocity, with 12mm c/c spacing of

bars. Nos. 1 25000 25000

6.2 Fine Screen (for 0.6 m/s inlet velocity and 0.9 m/s

outlet velocity, with 6mm c/c spacing of bars.Nos. 1 20000 20000


S. NO. (DSR-

2016)



chlorine dosing system consisting of one HDPE

tank of 100 liters capacity with a positive

displacement diaphragm dosing pump having

variable flow rate of (0-6 LPH). The motor shall be

suitable for operation at 240V/ single phase/50

Hertz supply. The pump shall be supplied

complete with necessary polypropylene piping,

valves, strainers & injection fittings for complete

automatic dosing. Set 1 30000 30000


level controllers & indicators for automatic

operation of the complete system. Job 1 45000 45000

9.0 Providing, fixing, testing & commissioning of fully

submersible, centrifugal non-clog type sewage

handling pumps capable of handling solids upto

35-40mm for raw sewage transfer from

equalization tank to SBR tanks and by pass the

sewage to municipal sewer in the time of

maintenance . The pump shall have CI casing &

impeller, SS shaft, TEFC induction motor including

pressure gauge, lifting arrangement for the pump,

all necessary piping (flexible pipe with coupling),

delivery header valves, tube type level indicator,

level controller with wiring to control the level of

sump automatically. etc. Receiving tanks shall be

completed with inlet, outlet, drain arrangement

(Pipe + Valve). Arrangement shall be provided in

the header for future connection of pumps. All

pipe sizes shall be desinged on the full capacity of

STP or provision of alternate arrangement to be

done as per vendor design.

Equalized Waste Water Transfer Pumps : DP /

Ebara / ITT(2 Nos. - 1 W +1 S)

Flow rate (each) - 12 m3 / hr

Head - 10 Mtr

Solid Handling - 35- 40mm

Total No. of Pumps (2 Nos. – 1 W + 1 S) Set 1 165,000.00 165000


S. NO. (DSR-

2016)


10.0 Providing, fixing, testing & commissioning of

horizontal, centrifugal Sludge Recirculation Pump

for the disposal of sludge to settling tanks of ETP &

STP to sludge holding tank and Aeration tank. The

pumps shall have CI casing, Impeller, SS shaft &

sleeve with mechanical rotary shaft seal connected

by a flexible tier type coupling to TEFC induction

motor mounted on a common channel base-plate

with coupling guard with efficiency class IE3 or EFF-

1 whichever is more efficient, 150 mm dia

pressure gauge with GM isolation cock, suitable

vibration eliminator pads of approved design.

Motor to be suitable for 415 + 10% volt, for 3

phase, 50 cycle AC supply including all necessary

piping, valves and other accessories complete as

required.

Sludge Transfer / Recircualation pumps - Kirloskar

/ M&P / Johnson(2 Nos. -1 W + 1S )

Flow Rate (each) - 4 m3 / hr

Head - 10 Mtr

Solid Handling - 10-12 mm

Type of Pump - Centrifugal Sludge recirculation

pumpTotal No. of Pumps (2 Nos. – 1 W + 1 S)

No. of Pumps (2 Nos. – 1 W + 1 S) Set 1 115,000.00 115000

11.0 Air diffusion system shall include the following:

11.1 Twin type rotary air blowers casing - CI, shaft-

Alloy Steel, capable of delivering 260 cum/hr

(each) of free air at 0.55 kg/sq.cm driven through

“V” belt or directly coupled through flexible

coupling to a TEFC motor of suitable HP Suitable

for 415 ± 10% volts, 3 phase, 50 cycles A/C

supply. Arrangement shall be provided in the

header for future connection of blowers. All pipe

sizes shall be desinged on the full capacity of STP

or provision of alternate arrangement to be done

as per vendor design for future connection. -

Evereset / Beta / Kay / Usha

Total no. of Blowers - 2 Nos.

No. of Blowers (2 Nos. – 1 W + 1 S) Set 1 145,000.00 145000

11.2 Air piping shall comprise of pipes droppers/

laterals with SS 304 Header complete with all

fittings such as tees, crosses, plugs, sockets,

elbows, reducers, supports & clamps etc cutting

chases & making good. Contactor to submit

detailed P & I indicating their proposal for

complete system. - Jindal / Tata Job 1 135,000.00 135000


S. NO. (DSR-

2016)


11.3 Non-clog type air dispersion system capable of

handling 3-5 cfm of air with oxygen transfer

efficiency of 3-4% per/meter water depth. Air

dispersion grid shall be assembled in modular

form so that they can be replaced / repaired

easily from platform at the top. (Imported fine

bubble membrane diffusers) - Rehau / OTT / EDIJob 1 145,000.00 145000

Note :

Air dispersion system shall be provided for Sewage

Sumps for ETP & STP, Settling tanks & SBR Tanks.

12.0 Providing and fixing all interconnecting piping (as

described below) and isolation control valves for

making the system complete. The piping material

shall be GI otherwise 10 bar pressure rating. -

Jindal / Tataa) All piping submerged in sewage waste/pumping

sewage waste shall be HDPE.b) All piping for treatment plant & post treatment

plant shall also be in GI (medium duty).Job 1 195,000.00 195000

13.0 Supplying, installing, testing & commissioning of

Submersible Jet Areator in Eqalization Tank 2 Nos. -

Wastech Enviro / ABS / Sulzer

Capacity : 150 M3/Hr

MOC :CI No. 1 115,000.00 115000

14 Supply, installation, testing & commissioning of

motorized Moving Decanter to suit SBR tank with

MOC SS-304 with scum guard and connected with

ultrasonic level transmitter & ultrasonic level

element for automatic control etc. complete as

required. Make of Decanter : Premier Tech /

C-Tech / Wastech - Wastech Envrio

Solution / HydroconNo 1 675,000.00 675,000.00


S. NO. (DSR-

2016)


15.0Supplying, installation & commissioning of

centrifuge non-submersible type pumps, TEFC

induction motor with efficiency class IE3 or EFF-1

whichever is more efficient, to feed semi tested

water to secondary treatment process through

sand pressure filter, activated carbon filter and

softener (Dry run protection). 1 no pressure gauge

4”dial with valve tee and fittings. 2 Nos cast iron

lever operated slim seal type butterfly valves of CI

body and spheroidal graphite iron disc with nitrile

rubber seal tested to 10 Kg /sq cm conforming to

BS 5155/MF6 standards and including a set of GI

flanges as BS -10 table including bolts, GI washers,

neoprene rubber gaskets, complete etc.

Arrangement shall be provided in the header for

future connection of pumps. All pipe sizes shall be

desinged on the full capacity of STP or provision of

alternate arrangement to be done as per vendor

design to meet the future requirement.

15.1 Filter Feed Pumps: - Kirloskar / M&P / Johnson

Capacity : 10 Cum/hr.

Head : 30 - 35 Mtrs

Type of Pump : Horizonal Centrifugal pump

Total No. of Pumps (2 Nos. – 1 W + 1 S) Set 1 135,000.00 135000

16.0 Providing, fixing, testing and commissioning of

horizontal centrifugal treated/Soft water transfer

pumps. The pumps shall be made of C.I. casing, CI

impeller, SS shaft & sleeve. Mechanical seal

connected by to a TEFC induction motor mounted

on a common channel base-plate with efficiency

class IE3 or EFF-1 whichever is more efficient with

coupling guard 150 mm dia pressure gauge with

GM isolation cock, suitable vibration eliminator,

pads of approved design. Motor to be suitable for

400/440V, 3 phase 50 cycles AC power supply,

including all necessary piping, suction and delivery

header, individual suction and delivery of pump,

valves, NRV, pressure gauge and other accessories

and concrete foundation complete as required.

16.1 Flushing/Soft Water Transfer Pump - DP / Ebara /

ITTCapacity : 5 LPS

Head : 70 Mtrs



16.2 Irrigation pumps: - DP / Ebara / ITT

Capacity : 5 LPS

Head : 50 Mtrs




S. NO. (DSR-

2016)



single stage single entry drainage pumps

connected to TEFC submersible motor for 415 +

10% volts, 3 phase, 50 cycles A.C. power supply

with mechanical seal, pump connector unit with

rubber diaphragm and bend, vertical. discharge

pipe, in built level controller with operational

moded as one pump working at low level, both

pumps at high level with a hooter alarm and cut

off at dry level as determined. The pump shall be

provided with a lifting devise of pull chain/guide

rail & minimum 80 mm dia (G.I. heavy class) rising

main of 5m length including interconnecting

piping, valves (Ball Valve / Butterfly), Non return

valves (GM/CI) 15 m cable etc. as per requirement

complete in all respects. The pump panel with all

automation to be included in the scope of works.

(Pumps to be suitable to handle solids upto 10-12

mm size with CI body, CI impeller, S.S. shaft with

15 mtrs cable, double mechanical seal).Cost shall be inclusive of GI piping for lifting water

from sump to outside.Provision of guide ropes to guide submersible

pump from upper level to operational level in

sump basin with channels / angle section of MSEP

shall be made by the STP contractor. Plant room Drainage Pump: - DP / Ebara / ITT

Flow rate = 25 M3/Hr

Head = 10-12 Mts

Solid Handling = 10-12mm

1 Set = Two(2) Nos.Pumps (1 W + 1 SB) Set 1 165,000.00 165000

19.0 Multigrade Pressure Sand Filter:


S. NO. (DSR-

2016)



vertical self supporting Multigrade pressure

Pressure Sand Filter fabricated out of 8mm thick

M.S. plate with 10mm dished ends MS sheet as

per IS : 2825, pressure gauges at inlet & outlet,

sample cock, air vent valve, PVC/GI face piping,

distribution pipe with diffuser on top, manholes

and side holes with cover, under drains,

supporting legs flanged piping, CI butterfly valves

and all accessories, with initial charge of filter

media, painting inside with food grade epoxy paint

and outside with two coat of red oxide primer and

two or more coat of synthetic enamel paint

complete with bypass arrangement including

piping and valves of required no. and size. Filter

shall be supplied with initial charge of Filter media

like special graded sand with supporting media like

silex, gravel etc. The vender shall submit the

certificate of having tested the same. The filter

shall complete with pressure gauge at inlet &

outlet, sample cock, GI/PVC face

piping/interconnected piping, automatic timer

based multiport valve (control valve) and all

necessary accessories. Arrangement shall be Grain size of media =0.6- 1.2 mm

Flow rate per filter= 24000 lph

Filtration rate=18,000 lph / m 2

Working presssure= 3.5 kg / cm2

Test Pressure= 7 kg / cm2

Filter dia approximate: 1200 mm

Backwash duration: once in 16 hours for 20 min

Valve = Butterfly Valve Nos. 1 210,000.00 210000

PipeLine = GI / MS C Class

20.0 Activated Carbon Filter:


S. NO. (DSR-

2016)



vertical self supporting Activated Carbon Filter

fabricated out of 8mm thick M.S. plate with

10mm dished ends MS sheet as per IS : 2825,

pressure gauges at inlet & outlet, sample cock, air

vent valve, PVC/GI face piping, distribution pipe

with diffuser on top, manholes and side holes

with cover, under drains, supporting legs flanged

piping, CI butterfly valves and all accessories, with

initial charge of filter media, painting inside with

food grade epoxy paint and outside with two coat

of red oxide primer and two or more coat of

synthetic enamel paint complete with bypass

arrangement including piping and valves of

required no. and size. Filter shall be supplied with

initial charge of media like Activated Carbon

Media of 900 iodine value, with supporting media

like silex, gravel etc. The vender shall submit the

certificate of having tested the same. The filter

shall complete with pressure gauge at inlet &

outlet, sample cock, GI/PVC face

piping/interconnected piping, automatic timer

based multiport valve (control valve) and all

necessary accessories. Arrangement shall be

provided in the header for future connection of Flow rate per filter= 24000 lph

Filtration rate=18,000 lph / m 2

Working presssure= 3.5 kg / cm2

Test Pressure= 7 kg / cm2

Filter dia approximate: 1200 mm Nos. 1 205,000.00 205000

Valve = Butterfly Valve

PipeLine = GI / MS C Class

22.0 Hypo Dosing system:

Supplying, installation & commissioning of on line

automatic electronic sodium hypo chlorine dosing

unit with automatically operated dosing pump . -

Asia LMI / Toshcon / ProminentThe free chlorine in the filtered water shall not be

less than 0.5ppm.Type: Diaphragm

Capacity= 10 LPH

Min Actuating Pressure= 0.3 bar

Max Working pressure= 0.5 bar

Maximum Suction Pressure=1.5m

Motor = 0.5 HP

PP Storage Tank= 500 ltrs

No. of Pumps (2 Nos. – 1 W + 1 S) Set 1 45000 45000


S. NO. (DSR-

2016)


23.0 Providing & fixing of sludge handling arrangement

(Centrifuge) solid bowl type of required size for

upto 100 deg. celsius temperature to be placed on

a platform above the ground with arrangement for

sludge feed to centrifuge from centrifugal semi

open impeller sludge pumps at a distance as

required with watering and flushing arrangement.

Effluent from Centrifuge to be connected to

equilization tank and the entire equipment

mounted on MS base frame bolted to cement

concrete foundation complete with testing &

commissioning as required and as specify. -

Hydrocon / Penwalt / HumboldthSet 1 50000 50000

24.0 Fabrication and supply of Sludge Trolley in

Galvanized Steel with min. Dimensions of 950 mm

x 600mm x 500 mm depth (min. sheet thickness

2.0 mm) with handle and wheel barrow for

transport of sludge complete as per requirements

and as specified. - Fabricated Nos. 1 100000 100000

25.0 Supply, installing, testing & commissioning of

Ultravoilet dis-infection unit. The unit shall have

over 99.9 % colifirm from inlet to outlet. The dis-

infection chamber shall be constructed of SS 316L

on all weted parts. The UV lamp shall be of low

pressure mercury vapour type with hard glass

enclosure, the sockets shall be water tight &

vibration resistant. The lamp life shall be rated for

9000 hours. The access to the UV lamp shall be

without the need to interrupt the ballast circuit. -

Wastech / Alfa - Mumbai

The unit shall be designed for the transmission for

the 65% to 75% of the stp water complete with,

lamp out alert circuit & UV radiometer with 4 – 20

mA output.The UV unit shall have with reactor, cabinet

housing, cabinet cooling, treatment chamber,

electrical panel, temperature safety control,

lampout alert, UV radiometer along with UV

monitoring system and UV monitoring readout

panel. The UV Dosage should be > 60,000 uW –

Sec /sq.cm. The lamps should be selected based

upon the flow requirement of respective unit.

Automatic cleaning arrangement for the quartz

glass with the automatic wiper

Providing, installing, testing and commissioning of

UV system for treatment of tertiary treated water

of 15 m3/hr. Set 1 240,000.00 240000

26.0Variable Pore Microfiltration System for Flushing


S. NO. (DSR-

2016)


1

Supplying, installing, testing and commissioning of

VPMF System piping and Valves with all the

required accessories & chemical cleaning system,

complete in all respects. - System Supplier -

Wastech / Brisanzia / Hydrocon

1.1

VPMF Module (Fully Backwashable top to bottom

filtration with 1 Micron Rating) including SS 304,

Pneumatic Valve, PLC Electrical Panel, flow meter,

compressor and all other accessories making the

system complete

Flow rate : 5 cum/hr Output

Inlet TSS :- 30-50 mg/lt

Membrane MOC - Polymer - Fiber and SS 316

HousingMembrane Type :- Auto Backwashable

MicrofiltrationNo. of VPMF Module - 3 Number

Make of System - Wastech / Hydrocon / Brisanzia Set 1 550,000.00 550000

1.2 VPMF Feed Pump

Capacity 12 M3/hr each (1 W + 1 SB)

Head 20-25 Mts

RPM 2900

Make - Grundfos / Equivalent Set 1 135,000.00 135000

1.4

Supplying, installing, testing, commissioning of

centrifugal Backwash pumps with Complete SS -

304 with motor, pressure gauge with isolation

cock, Isolation valve, NRV on delivery line.

Isolation valve, strainer at suction. The pump shall

be suitable for 415±10% volts 3 phase AC supply .

Capacity : - 8 m³/h

Head : - 18- 20 m

No. of Pumps: 2 Nos. (1W + 1S)

Note-CIP pumps can be common with item no.c

Make - Grudfos / Equivalent Set 1 12,000.00 12000

1.5

Supplying, Installation, testing and commissioning

of PAC dosing system compromising of Sintex Tank

with inlet/ outlet connection, piping and valves

alongwith metering pump of 6 LPH for dosing.

Set 1

35,000.00 35000

Make - Asia LMI

1.6

Supply installation commissioning of PLC control

panel with all automation required like Pneumatic

valves, piping in UPVC PLC and other required

accessories.

Make PLC - Siemens, Pneumatic Valve - Danfos,

UPVC Pipe - Astral, Compressor - Elgi

Set 1

225,000.00 225000


S. NO. (DSR-

2016)


1.8Supply, installation & commissioning of HDPE

backwash tank of 1000 Litre capacity including

required level controller

Set 1

15,000.00 15000

27.0Providing, installing, testing and commissioning of

Water Flow meter Electro magnetic type suitable

for 0-25000 LPH - suitable sizes /dia ( Inlet To STP

& Treated water Line) Nos. 2 15,000.00 30000

28.0Providing, installing, testing and commissioning of

Online digital type pH meter.Nos. 1 50,000.00 50000

29.0 Bypass arrangement (During maintenance of STP)

including earth work in excavation/backfilling in all

types 80 NB of soil upto 1.5m depth and piping

from Equalization tank to municipal sewer

including all fittings, isolation

valves/NRV/Accessories and protection of under

ground pipes with anticorresive tapes etc required

to complete the system. (Approx. length

considered is 50 mtr.)Job 1 50,000.00 50000

Note:

All technical liasioning, inputs, documents,

meeting with Pollution Control Board for

“Consent to operate” including arranging raw

sewage for testing and commissioning shall be in

the scope of Contractor. Contractor shall include

the cost of all chemicals consumed during testing

& commissioning and the cost of such items of

works which are not explicitly mentioned above

but are mandatory to have pollution board

approval. However responsibility of obtaining

license for consent to operate shall be in other

agency's scope.

C. ELECTRICAL INSTALLATION

Note Electrical Control Panel - Vee4 tech / Tricolite /

Adlec / Advance panel / Sudhir PanelThe rates for the control panels apart from the

switches and instruments shall also include the

following :1 Supporting rigid steel frame work.

2 Cubicle type, 2mm thick CRCA sheet steel enclosed

3 Complete with interconnections and distribution

bus bars4 Proper bonding to earth

5 Painting / Lettering on switches and control

panels, the location they serve, providing on each

panels its circuit diagram6 All Panels shall have provision for the following :

a) Padlocking of panel doors


S. NO. (DSR-

2016)


b) Padlocking of MCCB's handles in 'OFF' position

7 Providing cable clamps / supports within panels

cable alley 8 TPN MCCB shall means 3 Pole MCCB with separate

neutral link of adequate size.9 All MCB's shall be minimum 10 kA breaking

capacity10 The breaking capacity of MCCB's are mentioned

panel wise. All MCCB's shall be provided with

static release and setting plugs.11 All motor feeders MCCB's shall be of motor duty

12 Rubber mats shall be provided in front of all

panels and shall be provided at th back where they

are accessible from the back as per IS 5424 - 1969

13 Control Panel shall be painted with light grey paint

shade No. 631 of IS - 514 Degree of protection for following type of

distribution panel enclosure shall be as per IS

13947 - 1993a) IP 42 for indoor panels

b) IP 55 for outdoor panels

15 All MCCB shall be provided with operating

mechanism for door interlock.16 Minimum bus bar cross section shall be required

for following fault level.a) 50 x 6 mm Aluminium for 20 kA. 1 Sec

17 Current density of Aluminium shall be 1 Sq. mm

for 1 Amp fire rated current of bus bars.18 GI flat earth bus shall be provided through out the

length of each panel19 MCC for submersible drainage pumps and

tubewells to be supplied by the pumps

manufacturers for complete compatibility20 Providing, installing, testing & commissioning of

motor control centres fabricated from 16 gauges

MS sheet with powder coated finish. The Control

Panels should be comparable with HP of the motor

as specified

ELECTRICAL PANEL

For filter feed pump, equalization pumps, sludge

recirculation pumps, Irrigation pumps, transfer

pumps, slurry pumps etc in plant room.

Incomer

200A TP+N MCCB (35KA)

Metering

(0-500) volts digital voltmeter with selector switch

protected by 2A control MCB's(0-200A) Digital ammeter with Selector Switch and

suitable ratio, CL-1, 10VA CT'sPhase indicating lamps with toggle switches

Bus Bar:


S. NO. (DSR-

2016)


300A TPN aluminium , colour coded bus bars

suitable for 415V, 50Hz. (after deration)

Outgoing:

1 No. 63A TPN MCCB for Hydropneumatic system

4 Nos. 40A TPN MCCB for Filter Feed Pumps

4 Nos. 40A TPN MCCB for Sewage Transfer Pumps

2 Nos. 32A TPN MCCB for Sewage Transfer Pumps

(ETP)2 Nos. 40A TPN MCCB for Sludge Recirculation

Pumps2 Nos. 40A TPN MCCB for Irrigation lifting Pumps

1 No. 40A TPN MCCB for Sump Pumps

5 Nos. 40A TPN MCB for Slurry Pumps/air blower

2 Nos. 63A TPN MCCB for Soft water Transfer

Pumps2 Nos. 40A TPN MCB for Softner feed Pumps

5 Nos. 32A TPN MCB for dosing pumps

1 Nos. 63A TPN MCCB for UF System

1 Nos. 40A TPN MCCB for UV System

1 Nos. 40A TPN MCCB for Centrifuge

2 Nos. 63A TPN MCCB spare

1 No. 32A TPN MCB spare

1 No. 40A TPN MCB spare

One (1) Nos. 15 HP motor with single phasing

prevention arrangement, O/L relays, ammeters

with CTs, ON/OFF / Trip indication lamps and push

buttons, potential free contacts for remote / local

operations, indication, interlocking and Auto

Manual Selector Switch as required for

Hydropneumatic systemFour (4) Nos. DOL starter for 5 HP motor with

single phasing prevention arrangement, O/L

relays, ammeters with CTs, ON/OFF / Trip

indication lamps and push buttons, potential free

contacts for remote / local operations, indication,

interlocking and Auto Manual Selector Switch as

required for Filter Feed pumps.

Two (2) Nos. DOL starter for 1 HP motor with






required for waste water transfer pumps (ETP)


S. NO. (DSR-

2016)


Four (4) Nos. DOL starter for 5 HP motor with






required for waste water transfer pumps (STP)







required for Sludge Recirculation Pumps

Two (2) Nos. DOL starter for 7.5 HP motor with






required for Soft water transfer Pumps







required for Softner Feed Pumps







required for Irrigation lifting Pumps

One (1) Nos. 3 HP motor with single phasing

prevention arrangement, O/L relays, ammeters

with CTs, ON/OFF / Trip indication lamps and push

buttons, potential free contacts for remote / local

operations, indication, interlocking and Auto

Manual Selector Switch as required for Sump

Pumps Two (2) Nos. DOL starter for 3 HP motor with






required for Slurry Pumps


S. NO. (DSR-

2016)


Four (4) Nos. DOL starter for 3 HP motor with






required for Air BlowerFive (5) Nos. DOL starter for 0.5 HP motor with






required for Dosing Pumps.Panel shall be designed on the actual HP as per

model selection of pumps and makes.Notes :

All MCCBs / MCBs shall be of 15 KA breaking

capacity and suitable for motor duty application.

All motor starters shall be provided with

Automatic level controllerDOL starters shall be used for mototrs below 10HP

and Star-Delta Starters for other motors .Provision shall be made for providing potential

free contacts to all pumps startersAll motor starters shall be provided with

Automatic level controller.DOL starters shall be used for mototrs below 10HP

and Star-Delta Starters for other motors.Provision shall be made for providing potential

free contacts to all pumps starters Provision for auto starters for all motors with level

controllers shall be made in the panel.Provision for dry run protection shall be made in

the panel.MCC for STP as described above

All Control system to make the STP fully

automatic. The operation of the pumps shall be

controlled by the level controller. Set 1 280,000.00 280,000.00

The panel should have sufficient no. of potential

free contacts for monitoring purposes.

PLC PANEL

1 Supply, installation, testing & commissioning of

the PLC based control panel with interlocking

arrangement with supply pumps,suction pumps,

modulating or shut-off valves including necessary

wiring, magnetic switches & sensors complete to

make the system functional with following

interlocking

i Construction: Compartmentalized Type Skid

Mounted, MCC Cum PLC Control panel will be free

standing; vertical, fabricated from CRCA steel

sheet 14/16 G conforming to degree of protection

IP-52 or better. Cable entry will be from bottom.

Colour shade - RAL 7032


S. NO. (DSR-

2016)


ii System Voltage: 380 to 410 Volts & 50HZ ( 415 V

±10% , AC, 50 HZ ±5% for India ). Surge protection

to be provided at every applicable point.

iii PLC: The Programmable Logic Controller [PLC]

shall consist of a PLC hardware, with 16k (min)

program memory shall be protected by a backup

battery with further memory protection from an

EEPROM.

iv HMI: 5.5 Inch Colour Touch screen HMI, will be

mounted on A Man-Machine Interface Terminal

(MMI) shall be mounted on the front of the main

control panel for control of the activated sludge

plant. It will provide a display of the process

parameters and equipment status. The display will

have an associated keypad. The system will allow

operator changes to set points and control of

equipment. The terminal shall include an alarm

annunciation with a dedicated alarm page and

allow acknowledgment of alarms.

Make:Siemens / ABB Set 1 300,000.00 300000

TOTAL 5,976,550.00

BORE WELL INSTALLATIONS (As per D.S.R.2016)

1.0 23.1 Boring/drilling bore well of required dia for casing/

strainer pipe, by suitable method prescribed in IS:

2800 (part I), including collecting samples from

different strata, preparing and submitting strata

chart/ bore log, including hire & running charges

of all equipments, tools, plants & machineries

required for the job, all complete as per direction

of Engineer -in-charge, upto 90 metre depth below

ground level.

23.1.1 All types of soil

23.1.1.

2

350 mm dia metre 40 405.45 16218.00

23.1.2 Rocky strata including Boulders

23.1.2.

2

350 mm diametre 15 895.25 13428.75

2 23.15 Providing and fixing Ball plug/bottom plug of

required dia to the bottom of pipe assembly of

tubewell as per IS:2800 (Part I)23.15.

2

150 mm diametre 2 230.75 461.50

3 23.8 `Gravel packing in tubewell construction in

accordance with IS: 4097, including providing

gravel fine/ medium/ coarse, in required grading &

sizes as per actual requirement, all complete as

per direction of Engineer-in-charge.cum 9 1175.6 10580.40

SECTION - XI


S. NO. (DSR-

2016)


4 23.10 Supplying, assembling, lowering and fixing in

vertical position in bore well, ERW (Electric

Resistance Welded) FE 410 mild steel screwed and

socketed/ plain ended casing pipes of required dia,

conforming to IS: 4270, of reputed & approved

make, including painted with outside surface with

two coats of anticorrosive paint of approved brand

and manufacture, including required hire & labour

charges, fittings & accessories, all complete, for all

depths, as per direction of Engineer-in-charge.

23.10.

2

150 mm nominal size dia having minimum wall

thickness 5.00 mm. metre 40 1,210.60 48424.00

5 23.11 Supplying, assembling, lowering and fixing in

vertical position in bore well, ERW (Electric

Resistance Welded) FE 410 plain slotted (having

slot of size 1.6/3.2 mm) mild steel threaded and

socketed / plain bevel ended pipe (type A) of

required dia, conforming to IS:8110, of reputed

and approved make, having wall thickness not less

than 5.40 mm, including painted with outside

surface with two coats of anticorrosive bitumestic

paint of approved brand and manufacture,

including hire & labour charges, fittings &

accessories, all complete, for all depths, as per

direction of Engineer -in-charge.

23.11.

2

150 mm nominal size diametre 8 1,291.50 10332.00

6

23.12

Development of tube well in accordance with IS :

2800 (part I) and IS: 11189, to establish maximum

rate of usable water yield without sand content

(beyond permissible limit), with required capacity

air compressor, running the compressor for

required time till well is fully developed,

measuring yield of well by "V" notch method or

any other approved method, measuring static level

& draw down etc. by step draw down method,

collecting water samples & getting tested in

approved laboratory, i/c disinfection of tubewell,

all complete, including hire & labour charges of air

compressor, tools & accessories etc., all as per

requirement and direction of Engineer-in-charge.

hour 12 542.2 6506.40

7

23.14

Providing and Fixing MS Clamp of required dia to

the top of casing housing pipe of tubewell as per

IS:2800 (Part I), including necessary bolts & nuts of

required size complete.23.14.

2150 mm dia

each 1 1017.7 1017.70

COST OF 1 BORE WELL 106,968.75

COST OF 3.0 BORE WELL 320,906.25


S. NO. (DSR-

2016)


BORE WELL INSTALLATIONS (NON-SCHEDULED ITEMS)

8

MR

Supplying & Installation of suitable Hp submersible

pump B.S or K.S.B or equivalent make with finolex

cable 1x3x2.5 squmm(upto 75mtr) withflexible

conduit 25mm dia, electrical out door pannel with

required electrical fitting such as MCB of 0-25Amp

(Havell or Indocopp or MDS make), Volt & Ampere

meter (AE make), single phase preventer (Minilac

or VSP -1 make) starter (L&T or BCH make) etc of

approved make, 40mm HDPE Pipe (25 mtr) and all

accessories complete as per requirement of site.

Each 3 123,000.00 369,000.00

NOTES

a) Contractor shall include the rate of electrical

control panels complete with all accessories

&controls, all Electrical/Mechanical items as

required to operate the system automatic/manual.

b) Contractor to select suitable HP of pumps .

c) Level Controller with sufficient nos. of low / high

level alarms, contacts with electrodes and control

wiring for the automatic operation of water supply

pumps, Submersible Sump Pumps, to achieve the

functional requirement shall be provided. Control

wiring between these pumps and water tanks shall

be provided.Domestic water pumps must start at

low water level in overhead domestic water tank

& stop at high level in that water tank. Dry running

protection shall be provided for all the

pumps.Sequencing shall be provided for each set

of pumps.

total 28,302,872.62

SECTION- XI


S. NO. Non DSR DESCRIPTION UNIT QTY. RATE AMOUNT

1 MRProviding , designing , installing Lift of capacity 26

persons (1768Kg) , macine room typeNo 4 3200000 12800000

The Broad specification/requirment are as follows

Basik data

Capacity- 1768 kg

Control- Selective collective

Drive type- Variable Voltage Variable Frequency

Elevator type- Bed/ Hospital elevator

Grouping- Single

No. of stops- 5

Rated Load- 1768 kg

Rated speed - 1m/s

Car in side Height -2200mm

Door Height- 2000mm

Door type- power with door lock

Head room -4500mm

pit height- 1800mm

Car depth-2400mm

Car width- 1600mm

Door width- 1100mm

Car Indicator- Dot Matrix

Intercom Type- 2- station Intercom

Car Finish- Stainless steel haireline

Landing door - Stainless steel haireline with two

speed power door and railing- standerd

The lift should be with - Automatic Rescue device ,

Emergency light invertor, fire man Drive , Lift

announcement system , load weighing device ,

Regeneration device etcRequired capacity motor and mechanical devices

should be of good quality

12800000Total


BOQ for Lift


VOLUME IIIengineeringprojects.com/Tender/UploadFiles/3435_Vol-III.pdf · 2018. 7. 27. · 25 5.40.1...

Documents

Transcript of VOLUME IIIengineeringprojects.com/Tender/UploadFiles/3435_Vol-III.pdf · 2018. 7. 27. · 25 5.40.1...