Vol. 22 No. 1 Spring 2010 NEWS Dan-Am Co. Headquarters€¦ · • EPA Rule 40 Part HHHHHH • 0.3...

NEWS Dan-Am Co. HeadquartersSpring Valley, MN

INSIDE:• NEW Liberty 3000 B• NEW SATA adam 2

• Post SEMA• EPA Rule 40 Part HHHHHH

• 0.3 L RPS Cup

Vol. 22 No. 1Spring 2010

10-0

130

Las Vegas Convention Center Excellent Turnout at SEMA 2009

Kornwestheim, Germany

SATA RPS (Rapid Preparation System), the innovative disposable cup for mixing, painting, refilling and storing of paint is not only available as 0.6L and 0.9L ver-sion, but now also available in the 0.3L version. The 0.3L cup version is especially suitable for the application of spot repair and specialty design, as these materials are usually required in smaller quantities. Further advantages are the scales for vari-ous mixing ratios which are printed in black on the cups and easy to read.

With only three components (cup – lid – sieve), the 0.3 L RPS cup version is as easy to handle as with the proven 0.6 L and 0.9 L versions.

SATA RPS: 0.3 L cup version Now Available in US

With the 0.3 L size cup, as well as the black, easy-to-read scales, the SATA RPS 0.3 L cup is available with QCC and threaded for the SATAminijet and SATA full size guns.

2009 was our first year to exhibit only at SEMA during industry week. It was a Las Vegas gamble that did pay off. It was the first year for the newly implemented Paint Body and Equipment Section (PBE), and the attendance at our booth was steady and pro-

ductive throughout the show. SEMA gave us the opportunity to speak with and answer questions for painters and shop owners from a global audience. PBE distributors from around the world were also there to learn

continued on page 9 - RPS 0.3L

On May 3rd, SATA will be releasing the new SATAjet 3000 B Liberty. It has all the great benefits and advantages of the SATAjet 3000 B, plus the brilliant new fin-ish that allows SATA to pay tribute to our the Red, White, and Blue. The polished anodized finish of the SATAjet 3000 Liberty is extremely durable. This new finish has bright dramatic colors, and the details of the Statue of Liberty pictured in the handle. Due to its special surface coating and its hand-adjusted spray fan pattern, this special edition spray gun is perfectly ready for everyday use in the paint shop.

The brilliant colors and photographic details are set off by the chrome con-trols. All painters/collectors can choose between the “Super Saver” HVLP ver-sion or the “Super Fast” RP version with optimized high pressure technolo-gy. So as not to distract from the image of the Statue of Liberty, this spray gun will only be available in the standard version.

A must have for every collector, this spray gun should not be missing in any display cabinet. It is also perfect as a gift on special occasions or as recog-nition for employees who delivered outstanding results. This is very limited

edition spray gun, so make sure you order yours now. Deliveries are expect-ed to begin first week of May 2010, so do not wait to order and miss the chance for this awesome tribute to the Statue of Liberty and this great country we live in.

Dan-Am put up a 1,950 square foot SATA Spray Equipment exhibit and had a great show at SEMA 2009, Las Vegas

continued on page 6 - SEMA 2009

Introducing the next generation

The NEW SATA® adam™ 2The newly developed SATA adam 2 was

not only developed with cost effect measures to will help in these tough times, but also to have digital pressure readout on all your SATA guns. SATAadam 2 allows the exact adjustment of the spray pressure on paint spray guns with an accuracy of +/- 0.05 bar (1 psi). Permanent spray pressure control during painting significantly contributes to perfect color matching and high quality finishes preventing costly reworks due to incorrect pressure setting. Consisting of two separate components, the docking base and display, the docking base stays with the spray gun and holds the display, the display then can move

continued on page 2 - SATAadam 2

Very limited supply, so reserve your Liberty 3000 B today!

3Visit www.satausa.com for up-to-date news2 Visit www.satausa.com for up-to-date news

SATA Adam 2 Available - May 2010

TECH TIPS

Q: My shop is switching over to water-borne paint. What are the differences in the hand-held air blowers available.

A: There are some very big differences. The SATA Dry-jet only uses 8.2 CFM at 29 psi. That is the lowest one avail-able in the market. Today, with such high demands on the air compressor, using less air, to gain more is very critical. Also, when used at 29 psi, and at a distance of 39 inches from the panel, the SATA Dry-jet magnifies the input CFM by 10 times. This means huge amount of air on the output side, gently scrubs the surface, and carries away the water, to dry the paint film quickly, with a low air consumption, and a low cost. Competitive mod-els out there use as much as 21 cfm. Many low cost import models use 17 to 19 CFM, but do not magnify that amount on the output, so they simply do not dry as fast, but waste air in the

shop. Compressed air is so expensive to produce, that it is critical to use that resource economically. Again, the SATA Dry-jet uses less air, and dries paint faster than the others.

Q: How far away from the panel should I use my SATA Dry-jet?

A: That is a very important part of using the SATA Dry-jet. The Dry-jet should be used at 29 to no more than 35 psi, and at a distance from the panel of 39 inches. At that distance, and when blown at an angle, the air picks up the water, and removes it. Your dry times increase very quickly. If you move too close to the panel, it simply skins over the surface, and does not remove the water, but instead traps it underneath. You will then see it start to re-wet the surface, or worse, find tape tracking or adhesion issues due to the waterborne paint not being properly dried. By

backing up to 39 inches, setting the pressure correctly at 29 psi to max 35 psi, setting the Dry-jet to blow at an angle to the object (not straight on), the SATA Dry-jet will dry the water-borne paint very quickly, and uses very little air.

Q Can I connect my SATA Dry-jet to any air source?

A The gun requires only 8.2 CFM. So most filters allow that amount, so vol-ume will not be an issue. But what is more important, is how clean the air is. Remember that the air is blowing across the surface of the waterborne paint, and that has to be very clean. Much of the air that is currently being used in shops as they switch to water-borne is not clean enough. When they were spraying solvent, small traces of oil droplets or oil vapors would mix with the solvent, and not be an issue.

Now with water, the oil in particle form, or in vapor form does not mix with water, but instead floats or lays on the surface of the paint, causing signif-icant contamination, and in most cases small fisheye like failures. Adhesion can also be very adversely effected by the oily contaminants.

The SATA 484 filter, with 129.6 CFM as well as the SATA 284 filter, with 70 CFM are both 3 stage fil-ters, which purify air to breathing air quality. They filter particles down to 0.01 micron, plus add the carbon in the charcoal filter stage to remove remaining oil vapors. By bringing your spraying air to breathing air qual-ity, paint jobs improve dramatically, and today’s waterborne paint, as well as today’s high solids clears look bet-ter than ever. Plus the added CFM capabilities let you run multiple SATA Dry-jets without restriction.

Here are some excerpts from the discussion forum on our web site www.satausa.com. Minor corrections or changes have been made to the text for clarity. If you have a question about SATA spray equipment visit our web site and click on FORUM.

By Wayne Volkart

❖

Spring 2010

Dear SATA Customer: Dan-Am Company is the exclusive independent nationwide distribu-tor for SATA Spray Equipment and publishes SATA NEWS. Thus, we inform the industry about the latest SATA technical developments, top quality products and general trade information. SATA NEWS is provided free of charge to warehouses, jobbers and end users alike. Dan-Am Company does not sell direct, therefore, end users should contact their local supplier. Dan-Am Company takes great pride in the product and service we offer. We are certain you will be as impressed with the quality and performance of SATA Spray Equipment the same as thousands of other

satisfied customers. Dan-Am Company is not responsible for errors in text or pricing.

Dan-Am Co.®, Exclusive Independent Distributor of SATA products in the U.S. and Puerto Rico

All Orders:Toll Free - 800-533-8016 TeleFax - 800-633-7282Business - 507-346-7776 Int’l Fax - 507-346-7481

Visit our web site:www.satausa.come-mail: [email protected]

Errors and technical alterations reserved - SATA, SATAjet and/or other SATA products referenced herein are either registered trademarks or trademarks of SATA GmbH & Co. KG in the U.S. and/or other countries.

from spray gun to spray gun as long as there is a docking base attached to it. Because the display is removable and portable to other spry guns with docking stations there is no need to purchase additional air micrometers. The display removal also makes it easier for cleaning and maintenance

SATA adam 2 dock:Adaptor plate for the SATA adam 2 display replaces the standard air micrometer. Available in two versions for SATA standard guns and SATA minijet guns, it now also features the micrometer function for pressure setting. The integrated seal provides full pressure setting functionality even when the display has been removed. Comes with protective cover when display is not mounted.

SATA adam 2 display: The digital readout which contains all electronic components. As the pressure is set by turning the setting wings on the docking base only, the digital display always remain in the upright position ensuring perfect pressure reading at all times. For increased safety during gun cleaning in gun washing machines, a simple, reliable click-in mechanism quickly releases the SATA adam 2 display from the dock. This mechanism also allows using the SATA adam 2 display on different SATA spray guns equipped with a docking base.

High practicalityIn the development stage, the focus was practicality of the SATA adam 2 version. The interchangeable digital gauge is shatter proof, also suitable for cleaning in gun washing machines and in compliance with the latest ATEX guidelines for protection in explosion hazardous areas (codified according to the EU Directive 94/9/EU (ATEX) for EX II 1 G an EEx ia IIC T4; FM approved). To extend the battery lifetime, the electronic components are shifted into a sleep mode while the device is not in use. The battery with an average lifetime of approx. two to three years depending on usage can be easily replaced by the end-user.

All going DIGITAL All SATA paint spray guns with an integrated air micrometer can now be upgraded with the SATA adam 2. The assembly is very simple and quick - the standard air micrometer is replaced by the retrofit SATA adam 2 with just a few easy steps.

Remove air micrometer Insert the dock

Attach the display SATAjet 3000 B with the adam 2 is now ready

continued from page 1 - SATAadam 2

Order numbersSATA adam 2 Order # 160853SATA adam 2 mini Order # 160887SATA adam 2 display only Order # 160697SATA adam 2 dock, each Order # 160788SATA adam 2 dock, 2 pack (std sz) Order # 160796SATA adam 2 mini dock Order # 160861SATA adam 2 battery set Order # 160739

Craig lives in Alaska along the Kenai Peninsula coast which is located about 250 miles south of the city of Anchorage. He was raised in what is called "bush" Alaska by a old mountain man father by the name of Grizzly Grimes. He has 4 brothers and 2 sisters.

Craig works in many art mediums: paint-ing, drawing, scrimshaw, carving, inlay work, custom knives, pistol grips, rifle stocks, jewelry, photography, and digital imaging.

He has made thousands of pieces of art work that are now all over the world. Some are high end items, such as custom made pool cues or scrimshawed fossilized walrus or mammoth tusks. Some of his more affordable items consist of hand-made diamond willow walking canes, sculptures, carvings, pendants, pins, bolo's, belt buck-les, folding and skinner knives, note cards,

burl tables, clocks, and a varied number of other items.

As an artist Craig Stevens is at the top of his game. His shop is extensive, with wood working machinery of all kinds, metal lathes, milling machines, carving tools and just about every tool known to man. Most of the items he makes you won't find anywhere else. He likes mak-ing things that are rare and unique.

Scrimshaw is the age old art of etching with a needle on ivory or bone. The etching is done by scratching the surface of the ivory with a sharp object. Ink is then rubbed in to create the picture. In color scrimshaw it is done with acrylics or oil paints. Each color is done one layer at a time, working from darks to lights. Craig Stevens chooses fossilized walrus or mammoth ivory for his scrimshaw. This adds a unique challenge as fossilized ivories vary in color and take exceptional skill to add images while main-taining and utilizing the beautiful colors of the fossil ivory. As you can see from the examples, Craig does an exceptional job.

3Visit www.satausa.com for up-to-date news2 Visit www.satausa.com for up-to-date news Spring 2010

Even being close to the North Pole

Can't Stop a SATAminijet

Dear Sata,

I do not normally do this kind of thing but some

things just make it worth the effort. So here goes....

The reason I am writing your company is to say how

pleased I am with your product. (I own 2 minijets,

HVLP/2 and a HVLP/3) I first used one of these guns

when working for someone else about 20 years ago

and just loved the gun. Well I purchased one and

then a second and lets just say they have been with

me a long time and have seen more use that one

could imagine for a little gun. (if it were miles on a

car I am sure it would be turning the 10,000,000 mile mark.)

they have never once let me down and always perform just

flawlessly. I have talked many people into buying one (think I

am an unpaid sales rep for your company! lol)

I have made pool cues that have sold for over $25,000, pistol

grips that average $1500. High end custom knives, (skinners,

folders, daggers, you name it) I build hundreds of high end ear-

rings, and all different kinds of jewelry, from walking canes to

bow grips. Heck, I have even painted a couple of hot rod cars

with it! It is one of my tools I cannot do without and I thank

your company greatly for making such a exceptional product.

I contribute part of my success to the fact I use your guns.

(I simply will not use any others, I believe in quality when it

comes to my tools and yours are some of my most cherished.),

so to you and all of your staff I take off my hat and give a bow.

Exceptional....truly exceptional.

Thank you so much!,

Craig Stevensoriginal text from Craig

I wish we had more room to show Craig's exquisite handcrafted images, please check out his web site, he is also a very gifted painter.

www.craigstevensstudio.com

The transformation to waterborne is in full swing as was witnessed by the move in California and the OTC (east coast). Transforming the move to waterborne doesn’t have to be hard on the pocket book, by looking at your current equip-ment and seeing what it takes to upgrade it instead of going all out and buying everything new.

There are a few major areas to focus on to be ready for the switch to waterborne, Air Purity, Corrosion Resistant Equip-ment, Clean Air Drying Equip-ment.

Air Quality When switching to waterborne, one of the most important things to look into is the air quality and volume of air.

As compressed air flows through the

air supply pipes, condensation, scale and oil or oil vapor can be carried along downstream. Even tiny amounts of oil residue are a clear-cut source of coating

contamination. That is usually not a problem for sanders and some

other air tools. But it can be a problem for breathing

air and/or spraying paint material – particularly waterborne. Waterborne

paint is extremely sensi-tive to oil contamination. Oil contamination intro-duces oil droplets and oil vapor into the air stream for breathing air and usu-

ally causes very small sili-cone-like craters (fish eyes) in

the paint coating. That results in expen-sive repair work regardless of whether conventional solvent-based or waterborne

material is used.The two-stage filter system has been

standard equipment in many quality body shops. However when compressed air is carried downstream typical two-stage filter units cannot purge oil vapor. Usu-ally oil vapor can be detected by odor if the painter is us-ing a supplied air respirator. When spraying waterborne, adding a (464 filter) third stage acti-vated charcoal filter is ideal. Activated charcoal absorbs oil and organic vapors in compressed air making it suitable for breathing air and spraying waterborne. This combination makes it a very cost ef-

fective way to upgrade your existing filter system.Corrosion Resistant Equipment

With most spray guns made of alumi-num, a painter needs to take particular attention to cleaning the spray gun very thoroughly after use. If you put water and aluminum together you get a very cor-rosive reaction, so if the spray gun is not set up for waterborne material and there is residue left in the gun, the result will be corrosion which deteriorates the spray gun over time making it very inefficient and sometimes useless. SATA’s new spray guns, in particular the SATAjet 3000 HVLP, RP and the SATAminijet 3000 B, fluid passages have a special coating to safeguard against internal corrosion. Also the gun bodies and all control parts are now plated with a corrosion-resis-tant, high-gloss Chrome finish. And of

Critical Components Painting with Waterborne Material

The SATAjet 3000 HVLP and RP are SATA's premium class spray guns for spraying waterborne.

continued on page 12 - Waterborne❖

Grizzly Grimes

Scrimshaw - Killer Whale

Scrimshaw - Walrus

Scrimshaw - Belt Bukles

Folding knives

Skinner knives

Ear rings

5Visit www.satausa.com for up-to-date news4 Visit www.satausa.com for up-to-date newsSpring 2010

It's a low cost, extremely versatile spray gun that can be used for anything from small spot repairs to large surfaces. The gun features a lightweight ergonomic design and achieves a transfer rate of > 65%. It may be used for the application of both waterborne and sol-vent-based primer. 10.2 cfm at 29 psi.

SATAjet 100™ B F RP

SATAjet 100 B - Ultimate Primer Gun for Professional Painters

The SATAjet 100 B P is specially designed for the application of polyester spray putter/filler and is indis-pensable for creating high film builds along with a sharp-edged fan. Due to the new QCC cup connection the SATAjet 100 B is also perfectly suitable for use with the SATA RPS disposable cups.8.7 cfm at 29 psi.

SATAjet 100™ B F HVLP

Unmatched For Primer MaterialPreparation materials such as primer, filler and spray putty have an important function within the paint application process. Therefore, particu-lar attention must be given to the application of these materials and the use of the correct paint spray gun. The fine material atomization and the wide fan of the SATAjet 100 B provides smooth surfaces and eliminates rework. Precious work time is saved due to reduced sanding efforts.

Nozzle Product Nos. Size 0.6 L PVC Cup 1.0 L Alum Cup 2.5 mm 145185 147470

Spray Gun Model

SATAjet 100 BP

SATAjet 100™ B P (Polyester)The fan pattern is characterized by distinctive edges with extremely fine atomization and reduced overspray. The result is less sanding and masking and provides considerable material saving. A primer/filler spray gun that pro-vides a quick return on investment makes a profitable and highly attractive purchase for every body shop!12.5 cfm at 29 psi.

Nozzle Product Nos. Size 0.6 L PVC Cup 1.0 L Alum Cup1.4 mm 146373 1463991.7 mm 145722 1461911.9 mm 145730 1462092.1 mm 145748 147462

Spray Gun Model

SATAjet 100 BF HVLP

Topcoat: Spray Guns for a Professional Finish

SATAminijet® 3000 B HVLP

Design precision in miniatureA miniature paint spray gun design with low over-spray. Unsurpassed atomization ensuring excellent finish results and highest transfer efficiency. It's a full-fledged paint gun offering a perfect solution for hard to access areas, design work or small surfaces. Special nozzle sets are available for spot repair. A fan control is located on both sides for right or left-handed painters. With chrome finish and internal corrosion protection for spraying waterborne. 4.1 cfm at 29 psi.

0.3mm0.5mm0.8mm1.0mm1.1mm0.8SR1.0SR1.2SR1.4SR

125633-15125641-15

128512128520128538128488128496125765128504

125633125641125658125666125674125724125732125740125757

callcallcallcallcall

125724-3125732-3125740-3125757-3

NozzleSize

With .150L Alum. Cup

With .125L Plastic Cup

With .3L Plastic Cup

SATAminijet 3000 B HVLP

Numerous innovations make SATA spray guns well adapted to painter’s requirements. SATA adam™Retrofit air micrometer with digital display.

SATA CCS™Color Code Systemfor individual marking and identification SATA QCC™Quick Cup Connector™patented means of quick cup change with only 1/4 turn. SATA QC™Quick Change™ Air Capeliminates fine threads and easier to clean. SATA RPS™Mixing/Paint cup system

For videos, support and registration for the Premium Guarantee, please

go to www.sata.com.

Patented developments only from SATA

Suitable for SATA RPS – applicable without adapter

Easy maintenance – tool for changing the air distribution ring included

SATAjet® 3000™

Features: The latest nozzle concept for precision color matching and consistent paint distribution

Wide, even fan for faster working speed Perfect for basecoats and clearcoat application Completely chrome-plated for optimum corrosion protection

Unsurpassed material atomization VOC compliant equipment:

Switch to waterborne with the SATAjet 3000 Complies with VOC regulations for solvent emissions to protect the environment

Transfer efficiency rate of 65 % and up for both HVLP and RP

The enhancement of apremium class product.

Simple change of the battery – with battery kit 133 884

As the lead-ing manufac-turer of spray equipment for car refinish-ing, SATA has more than 80 years experi-ence in paint

spraying technology. SATA high-tech prod-ucts are widely accepted in more than 92 countries around the world. SATA's excellent reputation as a spray gun manufacturer is founded on state-of-the-art precision production processes. Strict, precise quality control during manufactur-ing and assembly ensure a permanent high level of quality in spray performance and atomization.

SATAjet® 3000 B RP

The Super SpeedPremium class high performance spray gun with enhanced high pressure technology. Re-gardless of the lower inlet pressure, the SATAjet RP maintains the fast working speed painters are accustom to with conventional spray guns. It meets the requirements of VOC legislation. Finish results have been confirmed by recommendations from the leading paint manufacturers. Designed to use with topcoat materials such as clearcoats, basecoats and single stage materials. 10.4 cfm at 29 psi.

The Super SaverPremium class, high performance spray gun with low over-spray, low pressure HVLP technology. More profit and better finishes with any paint material. The modern gun body design and user-friendly controls allow fatigue-free work and secure handling of the spray gun. Optional digital pressure readout and fan control for left-handed painters are available. Designed to use with topcoat mate-rials such as clearcoats, basecoats and single stage materials. 15.2 cfm at 29 psi.

NozzleSize

Digital 1.0L Alum. Cup

Digital .6LPlastic Cup

Standard 1.0LAlum. Cup

Standard .6LPlastic Cup

SATAjet 3000 B HVLP

*WSB, water solvent borne ** Hot Climate - water solvent borne *** Low Viscosity

Dan-Am Gun Cleaning Kit

Order No. 64035

As must have for every painter,helps keeps your spray guns in top condition for optimum performance.

Includes;

5 Mini brushes

1 Plastic handle brush

3 Large brushes (assorted sizes)

2 Claeaning Brushes w/handle

2 Double ended brushes

2 Cleaning broaches

1 Spray gun lube oil, 1/2 oz.

1.0 mm1.2 mm1.3 mm1.4 mm1.6 mm1.8 mm2.0 mm2.5 mm

132610-1 132621 132639 132647 132654 132666-1 132678-1 132685-1

132610-6 143297 152025 132647-6 132654-6 132666-6 132678-6 132685-6

118869 132431 132449 132456 132464 132589 136986

118950

118802 132308 132316 132324 132332 118810 132340

118851

NozzleSize

Digital 1.0L Alum. Cup

Digital .6LPlastic Cup

Standard 1.0LAlum. Cup

Standard .6LPlastic Cup

SATAjet 3000 B RP

SATAjet® 3000 B HVLP

1.0 133165-1 133165-6 118968 132787 1.2 133173 119065 133009 132795 WSB* 133223 142893 133058 132860 1.3 133181 119164 133017 132803 1.3 LV*** 161323 Call 161331 Call 1.4 133199 119859 133025 132811 1.4 HC** 148601 148817 148809 145797 1.5 133207 133207-6 133033 132829 1.7 133215 133215-6 133041 132837 1.9 133231-1 133231-6 119024 132845 2.2 133240-1 133240-6 119057 132652

Nozzle Product Nos. Size 0.6 L PVC Cup 1.0 L Alum Cup1.4 mm 146969 1534601.6 mm 145193 1461591.8 mm 145201 1461672.0 mm 145219 147439

Spray Gun Model

SATAjet 100 BF RP


Waterborne Drying Systems - Premium, Dan-Am and Econo-Jet Stands

SATA® dry-jet™ standFor drying larger areas of waterborne the stand is recommended. Up to three dry-jet blowguns can be mounted and aimed at the object. The drying area is doubled or tripled. The stand offers many advan-tages including unattended use and ita may be placed in any position. Blowguns rotate 360º. The stand is adjustable in height from 9.8 to 72.8 inches and 3.9 to 29.5 inches in width.

Dry-jet Stand only, Order No. 82198

Premium Waterborne Drying System

SATA® dry-jet™ options15.8 inch width extension w/one dry-jet blowgun (82222) ........... Order No. 86140

w/one dry-jet S blowgun (144105) ..... Order No. 144113

47.2 inch height extension ....................... Order No. 84145

SATA dry-jet blowgun filters, pkg of 3 ..... Order No. 82248

Blowgun filter holder ................................ Order No. 81869

SATA dry-jet stand

SATA dry-jet Part No. 82222

SATA dry-jet SPart No. 144105

w/2 dry-jet S gunsOrder No. 144113

w/2 dry-jet gunsOrder No. 82230

SATA® dry-jet™This practical, lightweight hand held blowgun makes quick work of drying waterborne ma-terial. A special nozzle design multiplies air volume from am-bient air using the venturi injec-tion principle. An air intake filter prevents contamination of the paint. The dry-jet blowgun is equipped with a shut-off valve. Air consumption is only 8.2 cfm at 29 psi. Lowest in its class.

Dan-Am Co. Dan-Am Dry-Jet gun stand.This new mobile stand can hold up to three jet-dry guns with its' large 48" horizontal mounting bar, no extension needed. Adjustable gun height from 40" to 88", with 360º swivel or tiIt. Supplied with high flow connections and hoses for maximum performance of the blow gun. It is easily set up and compact for storage, made of corrosion resistant zinc plated tubular steel with an aluminum tripod. The stand will be offered as a package with two guns.

Add-on blow gun SATA dry-jet "S" & hose assm. Part No. 720706 SATA dry-jet, & hose assm. Part No. 720708

SATA dry-jet SPart No. 144105



Dan-Am Jet-Dry StandPart No. 720700

This economical mobile stand holds up to two blow guns, adjustable gun height, with 360º swival or tiIt. Supplied with high flow connections and tubing for maximum performance of the blow gun. It is easily set up and compact for storage. It is fully compatible with SATA’s dry-jet blow gun and the SATA dry-jet “S”. The stand will be offered as a package with two guns. This is a must have tool for drying waterborne paint, as waterborne dries substantially faster with air flow, saving time for more added production.

Dan-Am Co. Econo-Jet blow gun stand.

Econo-Jet Blow Gun Stand



Econo-jet Blow Gun Stand

Econo-Jet Stand onlyPart No. 720580

SATA dry-jet Part No. 82222

Dan-Am dry-jet stand

“Always look for the original and distinctive SATA® design”

NIOSH APPROVED SATA Vision 2000 SUPPLIED AIR RESPIRATORSThe SATAvision™ 2000, part number 36384 (Type C continuous flow supplied air respirator with a full face shield), NIOSH approval number is TC-19C-211. The approval includes the belt unit with charcoal filter (No. 37200) and the full hood breathing respirator (No. 51854).

SATA® vision™ 2000 Full Hood Breathing Set Order No. 36384SATA vision 2000 Hood Only Order No. 51854 SATA vision 2000 Charcoal Filter Belt Unit Only Order No. 37200

SATA top air™ humidifier Order No. 89086SATA Belt Unit Support Straps Order No. 15412SATA Activated Charcoal Filter (Refill) Order No. 13904SATA vision™ 2000 Rep. Visor, 5pk Order No. 35659 25 pk Order No. 35675 50 pk Order No. 35050 100 pk Order No. 35100

Paint Whip Hose 52 inch Order No. 55640

High quality 3/8" Premoflex non-gassing hose in lengths from 25 to 100 feet.

25 feet Order No. 3366-25 35 feet Order No. 3366-35 50 feet Order No. 6633-50 60 feet Order No. 6633-60 75 feet Order No. 6633-75 100 feet Order No. 6633-100

Dan-Am Co. machine washable paint suits with hood, adjustable cuffs, elastic waistband and SATA logo.

X-Small Order No. 510050W Small Order No. 510052W Medium Order No. 510054W Large Order No. 510056W Xlarge Order No. 510058W 2X Large Order No. 510060W 3X Large Order No. 510062W

Dan-Am Paint Suit (white)

Breathing Air Hose

Spring 2010

SUG. LIST $39.95

NIOSH approved respirators must be supplied with Type 1, Grade D air within the approved pressure range at the point of attachment of the respirator to the air delivery system.

Filter Belt Unit

Top Air

Humidifier

Edition limited series spray guns. The attractive packag-ing and stunning orange fin-ish on the Foose Edition spray guns are both very collectible, yet completely functional in theshops. Chip Foose has been a loyal advocate of SATA for years. We continue to work together on upcoming projects, and were again very excited to have him in our booth at SEMA 2009.

If you were at the show, you got to see Chip’s truck that was featured on an episode of Overhaulin’. The other car in our booth is the amazing Stella D’ Oro, “Star of Gold” 33 Ford coupe. It is the finished proj-ect, and belongs to Mitch and Tara Lanzini, of Lanzini Body Works. Mitch has done many such stunning rides over the years, and has been featured on many of the Overhaulin’ episodes. The car’s finish and attention to detail made it an eye-catcher that was easy to see from isles away at SEMA. It was also featured in a previ-ous issue of SATA News, and on the home page of the Paint Body & Equipment section on SEMA’s website in 2009. He has been a long-time friend to SATA, and we were so pleased to have him each day in our booth. Our customers and his fans appreciate the smiles, and time Mitch takes to answer any and all questions. It was also the second year in a row that Mitch and Tara spent their anniversary with us, at SEMA. We couldn’t be happier to have them there.

Award winning bike builder and designer Kris Krome, together with Johnny K of Kris Krome Customs, Inc were also in our booth during the show. On display was their one of a kind board track racer names SATAjet. The bike features SATA gun bodies as foot pegs, and a SATA 1 to 1 Vario-Top diaphragm pump cover as an air cleaner. Also built into the bike were many SATA logos, including the one of a kind SATA logo chain, by Insane Chains of Florida. Kris and Johnny K spent the week signing auto-graphs and visiting with our customers about their work, and how they use only SATA products to produce their award winning results.

For artists this year we had three who spent time turning out amazing art work, and speaking with those who asked questions. We had Leah and Brian Gall of Finishline Designs, Jack Giachino of Giachino Art Studio, and JoAnne Bortles of Crazy Horse Painting showing off their talents throughout the show. Please look to the photos to see all three of our talented art-ists.

Upcoming new products were also unveiled. The new SATA Adam 2 was shown in its prototype form at SEMA. It will be available in May 2010. The new version Adam 2 has some great features. It consists of two components. The Adam 2 dis-play and the Adam dock. The Adam dock will come in two sizes. One to fit the full sized SATA guns, and the other to fit the SATA minijet series. Simply remove the air micrometer knob and replace it with the flat plate of the Adam dock. The new Adam 2 display can then be coupled into either dock, the full sized or mini version. This allows a painter to go digital on all of their SATA guns, and reduces the cost. Adjustment of pressure is now done with ease, and security. On the back side of the Adam dock, there are two places for fingers to press and turn the adjustment knob. This allows the Adam 2 gauge to stay upright and in place on the dock. It is also considerably lighter in weight that the previous version Adam. Now only one Adam 2 will be required, and multiple docks to fit all your SATA guns. It just got a lot easier to go Digital. The new Adam 2 will be available in May 2010.

On display we had mannequins fully suited in SATA Vision 2000 full hoods, and the awesome new Dan-Am Company Pro Series Paint Suits. The new Pro-Series suits have permanent anti-static carbon fiber sewn in, and the flexible back for stretch and comfort. They also include the popular flaming SATA skull design on the back. These new suits, as well as the white and gray suits are all now available.

SEMA 2009 was a great show that allowed us to meet with thousands of customers, and answer a lot of great questions. Hope to see all of you this coming November, for SEMA 2010.

more about what is coming in 2010. Our staff remained constantly busy answering questions primarily about what equipment was needed to spray waterborne materials.

Our booth offered displays showing each of the various tools and equipment that make spraying waterborne easy, and shops more productive. The two SATA filter series including both the 400 Filter series and the 200 filter series were on display. The 3-stage filters were most talked about with their ability to clean air down to 0.01 microns, and remove contaminants down to and including oil vapors. This is a critical part of success when spraying waterborne materials. But not only that, they offer clean air for breathing systems as well. Our displays also showed NIOSH approved sup-plied air respirators, which has become more and more popular in bodyshops across America. Also on display

were the complete RPS SATA single-use cups series. Available in 0.9 liter, 0.6 liter and 0.3 liter, the SATA RPS cups are there for any sized jobs. We had the cups, as well as the SATA RPS depot on display, and demonstrated the cups in our booth, and answered questions for all who had them. At another station, we had the SATA RCS, Rapid Cleaning System in use. This cleaning system makes cleaning a spray gun quickly between colors effortless, and efficient. In only 24 seconds, a painter can clean their spray gun, and be ready for the next color, while never leaving the booth. When spraying multiple bumper covers of various colors, or projects, this effective and efficient cleaner is a must. It is also another way to keep your SATA Spray guns in perfect

working order. During the show, we had a great interview and RCS product demonstration by Bryan Fuller from Two Guys Garage. It is a TV show on Speed Channel.

We also had many other celebrities and artists in our booth during the entire SEMA

show. The popular car designer and Overhaul in’ s tar Chip Foose was in our booth many times during the show. He also spent a few hours signing autographs for hun-dreds of loyal fans and car enthusiasts. On display in the booth was our just introduced SATAJet 3 0 0 0 B F o o s e


Quite a turn-out for Chip Foose's autograph, always a favorite at the SATA Booth,

Chip, showing off the SATA master-piece, SATAjet 3000B Foose Edition.

Mitch Lanzini, pauses for a moment during SEMA 20009. Mitch was gra-cious enough to show his Award Win-ning 1932 Roadster, Stella D'Oro, in the SATA booth at SEMA

Jon Kosmoski from House of Kolor and re-nown painter is always a favorite face at the SATA booth.

Brian Fuller stopped in to see some of SATA's new innovations, and got a demonstration on the new gun cleaner RCS (Rapid Cleaning System). Also had his picture taken with Dan-Am president Knud Jorgensen

Chip having some fun with one of SATA's painted hoods, I think he was the model for this one

Kris Krome, SATA bike designer/builder

Chip is by far one of the most enjoyable people we know to be associated with.Chip is very loyal to his fans and will sign just about any-thing you bring him.

SEMA 2009

SEMA 2009 - continued from page 1


Erik Lamb, Total Sales & Marketing, (pics- Tony Larimer, Erik Lamb, Knud Jorgensen, Albrecht Kruse)

David Voth, Complete Sales & Marketing, (pics- Tony Larimer, David Voth, Knud Jorgensen, Albrecht Kruse)

Advanced Collision Concepts, Mike Polonesi & Charles Lipford (pic- Knud Jorgensen, Tony Larimer, Charles Lipford, Mike Polonesi, Albrecht Kruse)

2009 SATA Agency of the Year, Advanced Collision Concepts, Charles Lipford & Mike Polonesi

Erik Lamb & Pete Carlsen, Total Sales & Marketing (pics- Tony Larimer, Erik Lamb, Knud Jorgensen, Albrecht Kruse)

Paul Patterson, Synergy Marketing Group, (pics- Tony Larimer, Paul Patterson, Knud Jorgensen, Albrecht Kruse)

David Voth, Complete Sales & Marketing, (pics- Tony Larimer, David Voth, Knud Jorgensen, Ablrecht Kruse)

Chris Gjelsten, BC Marketing Illinois & Indiana, (pics- Tony Larimer, Chris Gjelsten, Knud Jorgensen, Albrecht Kruse)

Pete Froehlich, Total Sales & Marketing, accepted by Erik Lamb, (pics- Tony Lairmer, Erik Lamb, Knud Jorgensen, Ablrecht Kruse)

Agency of the Year

Representative of the Year &RPS Salesman of the Year

Top Gun Award for Professional Shop Demonstrations

Substantial Growth Award

GRAPHICS AND AIRBRUSHING

Leah & Brian Gall

www.finishlineinc.com

AIRBRUSH CLASSES & INSTRUCTIONCOMPLETE PAINTING SERVICES763 - 416 - 4371

21725 County Road 10Corcoran, MN 55374

Wesco, Seattle, WA, (pics - Chip Foose, Knud Jorgensen, Bent Jorgensen, Jay White, Jeff Barger, Lloyd White)

Distributor of the Year

Substantial Growth Award

Substantial Growth AwardSubstantial Growth Award

Substantial Growth AwardSubstantial Growth Award

Leah Gall, a very talented painter is always a crowd pleaser.

SATA had the pleasure of some very talented artist showing there talents during SEMA. Shown here is Leah Gall and Jack Giachino, "The Italian", both are very talented airbrush artists and drew quite a crowd also present was JoAnne Bortles.

The Italian

JoAnne

Leah

2009 SATA Award Winners

Jack, “The Italian” Giachino, from Giachino Studios in Green Bay WI offers his talents during the show. See more of his work at www.giachinostudios.com.

JoAnn Bortles, artist and author from Crazy Horse Custom Painting does how-to-airbrush demonstrations in our booth again at SEMA 2009.

See her work at; www.crazyhorsepainting.com


PAINT STRIPPING AND

MISCELLANEOUS SURFACE COATING OPERATIONS

(SUBPART HHHHHH)What Is an Area Source?

• Any source that is not a major source. (A major source is a facility that emits, or has the potential to emit in the absence of controls, at least 10 tons per year (TPY) of individual hazardous air pollutants (HAP) or 25 TPY of combined HAP.)

Who Does This Rule Apply To?• Area sources that engage in any of the following:

ÿPaint stripping operations that use methylene chlo- ride (MeCl)-containing paint stripping formulations;

ÿSpray application of coatings to motor vehicles and mobile equipment;

ÿ Spray application of coatings to a plastic and/or metal substrate where the coatings contain compounds of chromium (Cr), lead (Pb), manganese (Mn), nickel (Ni), or cadmium (Cd).

This rule does not apply to:

• Surface coating or paint stripping performed on site at installations owned or operated by the Armed Forces of the United States.

• Surface coating or paint stripping of military munitions or equipment directly and exclusively used for the purposes of transporting military munitions.

Surface coating or paint stripping performed by individu-als on their personal vehicles, property or possessions, either as a hobby or for maintenance of their personal vehicles, possessions, or property provided they coat no more than two vehicles per year.

• Surface coating or paint stripping that meets the defini-tion of “research and laboratory activities.”

• Surface coating or paint stripping that meets the defini-tion of “quality control activities.”

• Surface coating or paint stripping that meets the defini-tion of “quality control activities.”

• Surface coating or paint stripping activities that are cov-ered under another area source NESHAP

Motor vehicle or mobile equipment surface coating opera-tions may petition the Administrator for an exemption from this subpart if you can demonstrate, to the satisfaction of the Administrator, that you spray apply no coatings that contain compounds of chromium (Cr), lead (Pb), manga-nese (Mn), nickel (Ni), or cadmium (Cd).

What Am I Required To Do?• Paint Stripping Operations—implement management practices that minimize emissions of MeCl.

ÿEvaluate the need for paint stripping (e.g., is it possible to re-coat without stripping?).

ÿ Evaluate each application to identify potential alternative stripping methods.

ÿ Reduce exposure of strippers to air.

ÿ Optimize application conditions.

ÿ Practice proper storage and disposal.

• For each paint stripping operation with > 1 ton MeCl annual usage, develop and implement a written MeCl minimization plan. No implementation plan is needed if

usage is < 1 ton MeCl; however, sources must still utilize work practices to minimize emissions of MeCl. Consult the MSDS sheet to identify the amount of MeCl contained in the paint stripper, but note that annual usage should not exceed 181 gallons of MeCl.

• Maintain records of annual usage of paint strippers con-taining MeCl.

• Motor Vehicle/Mobile Equipment/Miscellaneous Surface Coating Operations.

ÿTrain/certify all painters on spray gun equipment selection, spray techniques, maintenance, and environ- mental compliance (consult 73 FR 1738, pg. 1762, section 63.11173(f )(2)(i)-(iv)).

ÿInstall/operate filter technology on all spray booths/ stations/enclosures to achieve at least 98% capture efficiency.

ÿSpray booths/stations used to refinish complete motor vehicles or mobile equipment must be fully enclosed and ventilated at negative pressure or up to 0.05 inches water gauge positive pressure for booths that have seals on all doors and other open- ings and an automatic pressure balancing system.

ÿSpray booths/stations used to coat miscellaneous parts or products or vehicle subassemblies must have a full roof, at least three complete walls or side curtains, and ventilated so that air is drawn into the booth.

ÿ Spray-applied coatings must be applied with a high volume, low pressure (HVLP) spray gun, electro-static application, airless or air-assisted airless spray gun, or an equivalent technology.

ÿ Paint spray gun cleaning must be done so that an atomized mist or spray of the cleaning solvent is not created outside a container that collects used gun cleaning solvent.

ÿTrain and certify all personnel who spray apply surface coatings no later than 180 days after hiring or by July 7, 2008 (new sources) or by January 10, 2011 (existing sources).

What are the Impacts?• Most paint stripping facilities already comply with the rule requirements. Estimate 1,000 facilities will need to w take action to comply.

ÿReduce 1,000 tons MeCl annually,

ÿ Capital costs = $1.5 million.

ÿ Annual benefit = $0.9 million.

• Most surface coating facilities already comply with the rule requirements. Estimate < 25% of existing facilities will need to take some action to comply.

ÿ Reduce 6,900 tons of HAP annually including 11 tons of metal HAP.

ÿ Capital costs = $20 million; however, initial cost to be offset and recovered over time by cost savings as a result of more efficient use of labor and materials.

What Is The Compliance Date?• Existing Sources: January 10, 2011.

• New Sources: Upon startup after January 9, 2008.

• An affected source is a new source if you commenced construction of the source after September 17, 2007 by installing new paint stripping or surface coating equip-ment at a source not actively engaged in paint stripping and/or miscellaneous surface coating prior to September 17, 2007.

• An affected source is an existing source if it is not a new source or a reconstructed source (An affected source is reconstructed if it meets the definition of reconstruction in section 63.2.).

What are the Permitting Requirements?• Affected facilities are exempt from Title V permit require-

ments provided they are not required to obtain a permit for another reason.

What Reporting\Recordkeeping is Required? Reporting:

• Initial Notification (informs EPA that the facility is subject to the standards and when the source will be in compli-ance).

New Sources: July 7, 2008 or 180 days after startup

Existing Sources: January 11, 2010

• Notification of Compliance (certifies that the source is in compliance with the applicable requirements).

New Sources: As part of the Initial Notification

Existing Sources: March 11, 2011

• Annual notification of changes report—required each calendar year any reportable changes occur.

Recordkeeping (keep these records on file)

• Records to include copies of Notifications submitted to EPA.

• Painter training certifications.

• Spray booth filter efficiency documentation.

• Spray gun transfer efficiency.

• MeCl content information such as MSDS.

• Annual usage of MeCl for paint stripping, and written MeCl minimization plan if annual usage > 1 ton per year.

• Deviation and corrective action documentation.

Records to be maintained in a form suitable and readily available for expeditious review.

Summary of Regulations Controlling Air Emissions from Paint StriPPing and MiScellaneouS Surface coating oPerationS

national eMiSSion StandardS for HazardouS air PollutantS, neSHaP, (SubPart HHHHHH) FINAL RULE

This summary is sourced from; EPA Rule 40 CFR Bro-chure, Office of Air Quality Planning & Standards (EI 43-02), Dated April 2008www.epa.gov/ttw/eparules.html

This is printed as an overview of the EPA ruling part HHHHHH that will effect painters. Please refer to complete ruling at the EPA web site found at the end of the article.

SATA is dedicated to making this a smooth transition, please feel free to contact your local SATA representa-tive if you have questions on the EPA ruling, equipment or training/certifications of painters.

SATA spray gun transfer efficiency document may be downloaded from our website: www.satausa.com

Other documents such as RP approvals in HVLP manded areas and SCQAM regulations are also avail-able for downloading for your recordkeeping as part of this ruling.


RPS 0.3 L Now available!

Spray gun holderWall mount for safe, convenient storage of the spray gun.Order # 9886

Spray gun holderWall or bench mounted spray gun holder for easy refilling.Order # 40188

1 Liter pressure pump spray bottleCost effective means of intermedi-ate cleaning when spraying waterborne. Order # 127860

1 Liter squeeze bottleMade of pliable plastic for quick intermediate cleaning of fluid pas-sages. Order # 127852

RPS DepotStorage rack to hold up to three RPS cup boxes.Order #144840(without RPS boxes)

Cup-carrier basketfor safe transporta-tion of up to 6 RPS cups into the booth.Order # 127845

RPS Shaker Ring adapterSafely holds the RPS cup for use in a paint shakerOrder # 117051

SATA RPS ACCESSORIES

For ProfessionalsSATA RPS (Rapid Preparation System) is the ideal cup system for shops focusing on perfect finishes and high profitability. It makes the painters' work easier, considerably increases productivity and drastically reduces the consumption of cleaning solutions and solvents

0.9 l 0.6 l 0.3 l

118 471 125 062 118 281

118 489

151 720

125 070

151 746

118 406

40 x

40 x

40 xFor professionalsSATA RPS (Rapid Preparation System) is the ideal cup system for shops focusing on per-fect finishes and high profitability. It makes the painters’ work easier, considerably increases productivity and drastically reduces the con-sumption of cleaning solutions and solvents.

0.3 lSATAminijet

118 299**

118 414**

RPSsuitable for

flat sieve

sieve fineness

125 µ*

Order #

plug-in sieve

sieve fineness

200 µ*

Order #

flat sieve

sieve fineness

200 µ*

Order #

60 x

60 x

60 x

60 x57 x

57 x

57 x

SATAjet 3000 B, SATAjet 1000 B, SATAjet 100 B, SATAjet 2000 HVLP, SATAjet RP, SATA LM 2000, SATA KLC, SATAjet 90

*) For selecting the correct sieve fineness please ask your paint manufacturer.**) This variation fits directly on SATAminijet guns without bothersome adaptors.

The 0.3 L cup has two versions, one for the SATAminijet and for SATA full size guns, it attaches directly to SATA paint spray guns with QCC (Quick Cup Connector) or standard thread, no special adapter is required. Spray gun and RPS cup are the perfect match: the spray gun remains well-balanced, is noticeably light-er and cleaning is very simple, as only the short material passages have to be cleaned.

Painters emphasizing perfect color match and even material distribution do appreciate the gravity-flow cup prin-ciple allowing an even material flow.

Due to i ts disposable character, the cleaning of the cup becomes unneces-sary with RPS, thus saving the body shops valuable time and the use of solvents. Further cost savings are possible if sepa-rate mixing cups and sieves are eliminated from the work process.

SATA RPS 0.3L, 0.6L and 0.9L are sup-plied with sieves which are optionally available with 125µm or 200µm mesh size. For the correct type of sieve to be used, please refer to the recommendation of the respective paint manufacturer.

RPS Cups continued from page 1 PBE Big Event

In February 2010 Knud Jorgensen, Dan-Am Co. President, and Steve Treutel, Director of Industry Relations and Training attended the PBE Big Event in Burbank, CA. PBE, a warehouse dis-tributor based in Downey CA sponsors this event each year, and brings in many manufacturers and their customers from across the western and mountain regions of the USA. This year they had over 600 of their jobber distributor customers in attendance at this event. During the event there is a trade show setting where we get to show and discuss what is new.

This year we had the added advantage of sharing booth space next to Mothers. With both companies there is a great rela-tionship with Chip Foose. Having Chip nearby, answering questions, and sign-ing autographs the area around us was packed with interested people throughout the show. He has been a great spokes-person for Mothers products, as well as SATA. This year’s show also highlighted the work of TV and Magazine person-ality Rich Evans of Huntington Beach Bodyworks. Rich was also there sign-ing autographs, and helping us to pro-

mote the SATA line. The attention to our booth gave us great opportunities to talk about all the advantages of our products. With waterborne still being the focus in the west, our product line and marketing phrase H2O = SATA was a great match for this event.

Thank you to PBE for your efforts to make the Big Event a success again in 2010. Also thank you to the guys from Total Sales & Marketing for being great SATA representatives on the entire west coast!


Clean compressed air filtration for perfect finish resultsSATA FILTERS:

SATA Pressure RegulatorUsed with the 200 filter series 72cfm.Part # 47290

SATA 400 Series Filters:The SATA 400 modular filter series is designed to meet the highest standards of quality and performance. The modular system allows the user to adapt to varying shop conditions and requirements. Easy to service and maintain with no desiccant related problems. Dual gauges monitor pressure differential, thus a pressure variation of 10 to 15 psi or more indicate filter maintenance is required.

SATA combination filter systems are especially suitable for use with supplied air respirators providing 100% (technically 99.998%) clean breathing air.

SATA 200 Series:

Along with the 400, the 200 filter series is the most versatile modular filter system currently on the market but at an unbeatable price. The 200 is rated at 72 cfm @ 90 psi, more than adequate for many small shops. It can be connected to compressed air pipes from either the right or left side. When atomized air leaves the spray gun, it must be clean, dry and free of condensation, silicone, oil or any other contamination. Otherwise, the finished result can have a dull finish, fish eyes, water or dust. Clean, pure air is also a must for breathing air.

ThE 200 fIlTER SySTEm fOR SmAll OR InTERmEdIATE ShOPS

SATA 222 Single Stage Filter5 micron filter unit with pres-sure gauge and automatic condensate dis-charger. Without regulator and air module.Use as an unreg-ulated line filter.

Part #43687

SATA 420 Line Pressure Regulator High air volume of 141.3 cfm up to 225 psi inlet pressure Order Number 92288

Filter Outlet Module Standard filter outlet module Part # 59295 with/4 drop man. Part #59295-4

Air Connection Module Manifold for 494 filter only Part # 96743

SATA Air Connector Module200 manifold with two couplings and two nipples. 1/2" connection. Part # 1422244 drop manifold Part # 142224-4

0/400 Filter Service Kit Ongoing filter maintenance is important - especially working with waterborne. The service box with service reminder label includes a fine filter 81810 and a charcoal filter 85373 Part # 138933

Filter Replacement

Filter Accessories

SATA 444 Filter With Portable StandPerfect for use when filtered, com-pressed air is required at a remote workstation. The 444 is ideal for easy on-site filter demonstrations. Rugged heavy-duty tubular construction.Order Number 92833

Portable Filter Stand AloneOrder Number 28076

SATA 424 Single Stage Filter 5 micron oil / water separator unit with automatic condensa-tion discharge, pressure regulator and ball valve air connection module. 1/2 inch internal inlet thread and two 1/4 inch external outlet thread. Order Number 92221

SATA 424 L Single Stage In-Line Filter 5 micron oil / water separator unit with automatic condensation discharge and pres-sure regulator. Does not include ball valve air connection module. 1/2 inch internal inlet/outlet thread. Order Number 92262

SATA 414 Single Stage Filter 5 micron oil / water separator with automatic condensation discharge, with ball valve air connection module but with-out regulator. 1/2 inch internal inlet thread and two 1/4 inch external outlet thread. Order Number 92213

SATA 414 L Single Stage In-Line Filter 5 micron oil / water separator with automatic condensation discharge, without ball valve air connection module and regulator for in-line installa-tion. 1/2 inch internal inlet/ outlet thread. Order Number 92254

SATA 434 Single Stage Fine Filter 0.01 micro-fine filter unit with ball valve air connection module. Provides 99.998% clean

air. Compressed air must be pre-fil-tered when using this unit. 1/2 inch internal inlet thread and two 1/4 inch external outlet thread. Order Number 92239 (illustrated)

SATA 434 L Single Stage In-Line Fine Filter 0.01 micro-fine filter unit without ball valve air connection module. Provides 99.998% clean air. Compressed air must be pre-filtered when using this unit. 1/2 inch internal inlet/outlet thread. Order Number 92270

SATA 494 Triple Stage Fine Filter Same unit as the 484 detailed above except with two air connection modules.

Used in conjunction with the SATA industrial belt valve or spraying water borne paint. Complete with regulator and auto-

matic condensate discharger. 1/2 inch internal inlet threads.Order Number 92338

with/4 drop manifoldOrder Number 92338-4

Add-on unit with fittings without module. Order Number 92247A Line filter unit without fitting and module. Order number 92247L

SATA 444 Double Stage Fine FilterCombination fine filter unit for providing 100% clean (technically 99.998%) compressed air. The

ideal, basic choice for the spray booth for top quality paint jobs and breathing air for supplied air respirators. This system allows precise air pressure setting and filtration to 0.01 micron to remove silicone, oil, water and dust. Complete with automatic condensation discharge and ball

valve air connection module. 1/2 inch internal inlet thread and two 1/4 inch external outlet thread. Order Number 92296

with/4 drop manifold Order Number 92296-4

SATA 464 Activated Charcoal Filter Activated charcoal unit with two-¼ inch ball valve manifold for breathing air. Removes oil vapor and organic odors. Pre-filtering compressed air is required. ½ inch internal inlet thread. Order Number 92247

SATA 484 Triple Stage Fine FilterWhen using the SATA belt valve, breathing air

must be filtered through acti-vated charcoal on the wall-mounted filter. An activated charcoal stage is also an excellent choice when using water borne paint to remove

oil residue. Two ball valves and single air connections module. Order Number 92320

with/4 drop manifoldOrder Number 92320-4

SATA 264 Activated Charcoal Filter

Activated charcoal unit removes oil vapor and organic odors. Pre-filtering compressed air is required. Part # 141226

SATA 244 Dual Stage Filter0.01 micron fine filter unit with two

pressure gauges, automatic conden-sate discharger, air module and pres-sure regulator.

Use to connect regulated air to air tools and breathing air.

Part # 44404 with/4 drop manifoldPart # 44404-4

SATA 284 Triple Stage FilterAn economical three-stage filter unit. Stages include a 5 micron filter with automatic con-

densation discharger, a 0.01 micron fine filter and an activated charcoal filter for breathing air or spraying water borne.

Use with the SATA supplied air respi-rator industrial belt valve or ensuring removal of oil residue when spraying water borne paint.

Part # 141218 with/4 drop manifold Part # 141218-4

Paint Manufacturer Recommended

for Waterborne Material

SATA 242 Dual Stage Filter0.01 micron fine filter unit with two pressure gauges and automatic con-densate discharger. Without regulator and air module. Use as an unregu-lated line filter for very fine particle separation.

Part # 43752

SATA Particle Filter Sintered bronze filter for 100, 200, 300 and 400 series filters. May be cleaned with solvent, how-ever, replacement is recommended. Part # 22160

Micro-Fine filter For 100, 200, 300 and 400 filter series. Non–cleanable filter cartridge separates contamination to 0.01 micron. Part # 81810

Ultra-Fine filter For 300 and 400 filter series only. Non-cleanable special layered polypropylene filters to 0.0004 micron . Part # 85365

Activated charcoal filter cartridge For the wall mounted 364 and 464 filter series units. Removes oil vapor when using supplied air respirators. Part # 85373

SATA 474 Double Stage Fine Filter Add-on unit to existing pre-filter stage and is used for breathing air to supplied air respirators. 0.01 micron filtration consisting of the 434 fine filter and the 464 activated charcoal filter. 1/2 inch internal inlet thread and a two ball valve mani-fold. Order Number 92312

Recommended for Waterborne!



for Waterborne Material

Regulator BracketUsed with 47290 regulatorPart # 47290B


Dan-Am 10 - 40 Liter Pressure TanksDan-Am Company offers a new line of pressure tanks from 10 to 40 liter. These cost-effective tanks are supplied complete with a quality regulator, over-pressure valve, back-check valve and fluid shut-off valve. Dan-Am models include 10 pressure tanks with single or double pressure regulator either plain, with manual stirrer or with pneu-matic stirrer. Other 20 and 40 liter variations are also offered with single or double pressure regulator. Tanks are mounted on wheels for ease of handling and mobility.

Choose the system that fits your operationComplete 10-Liter without Agitator, Single Pressure Regulator Order No. 671100 Sug. List $469.00

Complete 10-Liter without Agitator, Double Pressure Regulator Order No. 681100 Sug. List $548.00

Complete 10-Liter with Manual Agitator, Single Pressure Regulator Order No. 671200 Sug. List $529.00

Complete 10-Liter with Manual Agitator, Double Pressure Regulator Order No. 681200 Sug. List $619.00

Complete 10-Liter with Pneumatic Agitator, Single Pressure Regulator Order No. 671300 Sug. List $889.00

Complete 10-Liter with Pneumatic Agitator, Double Pressure Regulator Order No. 681300 Sug. List $979.00

Complete 20-Liter with Manual Agitator, Single Pressure Regulator Order No. 672200 Sug. List $739.00

Complete 20-Liter with Manual Agitator, Double Pressure Regulator Order No. 682200 Sug. List $839.00

Complete 20-Liter with Pneumatic Agitator, Single Pressure Regulator Order No. 672300 Sug. List $1,039.00

Complete 20-Liter with Pneumatic Agitator, Double Pressure Regulator Order No. 682300 Sug. List $1,139.00

Complete 40-Liter with Pneumatic Agitator, Single Pressure Regulator Order No. 674300 Sug. List $1,149.00

Complete 40-Liter with Pneumatic Agitator, Double Pressure Regulator Order No. 684300 Sug. List $1,239.00

10 Liter

20 Liter 40 Liter

Do you have special system requirements? Call Dan-Am at 800-533-8016 and we will be happy to discuss your needs.

The Dan-Am 2.5 Qt. pressure tank and the SATAminijet 3000 B is a great combination for continuous painting of smaller objects and hard to reach areas. Special dual hose is includ-ed. The minijet is also convertible to a gravity fed spray gun with a gravity cup (incl). Dan-Am 2.5 Qt. Pressure Tank with Minijet 3000 BT and 3m Dan-Am Hose Combination

Dan-Am 2.5 Qt. Pressure Tank Only Complete deck and 2.5 qt. container Order No. 651100

Dan-Am 2.5 Qt. Pressure Tank with SATAminijet BT and 3m Dan-Am Hose Combination

Nozzle Size Part no.0.8 SR 6511901.0 SR 6511911.2 SR 651192

* Includes .125 ccm plastic cup for conversion to gravity

SATAjet® 3000 K™ HVLP & RP™ Pressure feed spray gun available in Digital or standard version

• Digital version adjustable with the adam• Shockproof and gun washer safe• RP (reduced pressure) VOC compliant • Wide fan for fast working speed• Special wear resistant nozzle sets available

*w/adam

Digital* 3000 K HVLP

9328692718

93294

96149

96156

Standard 3000 K HVLP

9338592924

93393

96164

96172

Digital* 3000 K RP

92692

93120

9313893146

9316193179

Standard 3000 K RP

92932

93336

9334493351

9336993377

NozzleSize0.81.01.11.21.31.51.61.72.0

SATAminijet® 3000 BT HVLP

• Special SR wide fan nozzle sets• Nine nozzle sizes to choose from• Fan control adjustable form either side • Features quick change cup and air cap• Air consumption only 4.1 cfm at 29 psi

Pressure feed spray gun convertible to Gravity

Part No.

SATAminijet 3000 BT, includes 90° adapter and 0.125L PVC cup

NozzleSize0.30.50.81.01.1

0.8SR1.0SR1.2SR1.4SR

w/Adapter & PVC Cup

125633PT125641PT152658PT125666PT125674PT125724PT125732PT125740PT125757PT

Spring 2010

Great spray pattern and ergonomics were the focus for the SATAjet 1000 K HVLP and RP. It’s compact, lighter, and painless on the

pocketbook. It features soft trigger pull and large fan similar to the

SATAjet K3 for fast working speed. Fewer air cap

and control threads avoid cross threading and cleaning is easier.

The SATAjet 1000 is polished anodized coating with stain-

less steel needle, fluid tip and material passages, making it ideal for waterborne.

SATAjet 1000K HVLP & 1000K RP™

0.81.01.11.21.31.51.61.72.02.53.04.05.0

Nozzle Size

Jet 1000KHVLP

Jet 1000KRP

SATAjet 1000K HVLP & RP

139196139204

139212

139220

139238

132092

132100

132118132126

132134132142153486153494154336

Call

Sug. List

$559.95

SATAjet 3000 K HVLP & RP

The versatile combination that allows the minijet SATAminijet 3000 B to be used with a pressure tank and convert to a gravity fed spray gun with the 0.125L PVC cup

Special 10' combina-tion minijet air and material hose.Part No. 675510

importance is a stainless steel paint needle and fluid tip that are an integral part of the SATAjet 3000 and SATAminijet 3000 B and corrosion resistant. These features en-sure superb internal and external corrosion protection and have made the SATAjet(s) one of the longest lasting guns on the market.Dry Waterborne fast and efficiently

In general the paint booth of today has been designed for solvent base material. It relies on heat to speed up solvent evapora-tion. On the other hand waterborne requires high airflow volume to speed water evapo-ration. Some drying systems now available are being offered for many thousands of dollars. Investments in expensive water-borne drying systems are not necessary. Cost effective alternatives from SATA are available. We find that even shops that have out fitted their b o o t h s w i t h expensive sta-tionary air dry-ing units are still buying por-table units like the SATA dry-jet and stand.

SATA reacted to demand by developing a simple to use, cost effective waterborne drying system named SATA dry-jet. This convenient blowgun can be hand held or mounted on a stand. The special design multiplies ambient air volume by utilizing the venturi injection principle. The SATA dry-jet has an intake filter to prevent paint contamination. It is equipped with a Teflon ball shut-off valve and air consumption is only 8.2 cfm at 29 psi. The SATA dry-jet @ 8.2 cfm, uses the least amount of air in the industry.

For drying larger surfaces a special stand is available. Up to 3 SATA dry-jet blow-guns can be mounted on the stand and aimed at the surface to be dried. That dou-bles or triples the drying action. Besides increasing the drying area, the stand allows for unattended use. This allows the painter to go about doing other tasks until the sur-face is dry. SATA dry-jet blowguns rotate 360º and may be locked in any position. The stand connects to a standard air hose with a QC and is adjustable from 9.8 to 72.8 inches in height and 3.9 to 29.5 inches in width. Optional height and width exten-sions are available.

The SATA dry-jet blowgun system is a cost effective means of solving the problem for quick drying of waterborne.

Dan-Am now offers three levels of

the dry-jet system, econo, standard and premium models are available today.

The SATA dry-jet stand is the ideal waterborne dry-ing system for large areas. Up to 3 dry-jet blowguns can be mounted and aimed for quick drying.

Waterborne - continued from page 3

SATA dry-jet is a practical, lightweight hand-held blowgun that makes quick work of drying water-borne material.

SATA gun cleaning posters are available in two methods, manual cleaning of the spray and gun washer cleaning. The poster will aid in keeping the cor-rect steps for a clean spray gun for optimum performance.The poster is two sided, 18" x 24", so depending on your method of cleaning, Manual or Gun Washer, we got it covered.

Please order Part #158162P.

The updated digital ver-

sion of the SATA catalog

is available online, visit

www.satausa.com and link

to our on-line catalog

• New Product Updates

• Replacement Parts

• Product Brochure Download

• Tips and Maintenance Advice

Vol. 22 No. 1 Spring 2010 NEWS Dan-Am Co. Headquarters€¦ · • EPA Rule 40 Part HHHHHH • 0.3...

Documents

Transcript of Vol. 22 No. 1 Spring 2010 NEWS Dan-Am Co. Headquarters€¦ · • EPA Rule 40 Part HHHHHH • 0.3...