Vita Needle Master Tubing Chart
1
STAINLESS STEEL TUBING Stock sizing for all Stock Hard Temper, TIG Welded and Drawn 304 Stainless Steel Tubing— sorted by OD. (Sizes marked with an asterisk are also stocked in 316 SS.) 919 Great Plain Avenue | Needham, Massachusetts 02492 Tel: 888-VITANEEDLE | Fax: 888-FAXVITA Email: [email protected] WWW.VITANEEDLE.COM NOMINAL TOLERANCES Gauge OD ID Wall OD ID/Wall 7XX* .180 .173 .0035 ±.001 ±.001 7X* .180 .166 .007 ±.001 ±.002 7TW* .180 .160 .010 ±.001 ±.002 7RW* .180 .150 .015 ±.001 ±.003 7HV .180 .131 .0245 ±.001 ±.003 7 ½* .172 .150 .011 ±.001 ±.003 8XXX .165 .156 .0045 ±.001 ±.002 8XX* .165 .150 .0075 ±.001 ±.0025 8TW* .165 .145 .010 ±.001 ±.002 8RW* .165 .135 .015 ±.001 ±.003 8HV .165 .117 .024 ±.001 ±.003 4.0 X 3.0 MM* .157 .118 .020 ±.0039 ±.0039 4.0 X 3.2 MM* .157 .125 .016 ±.0039 ±.0039 4.0 X 3.5 MM* .157 .137 .010 ±.0039 ±.0039 8 ½* .156 .136 .010 ±.001 ±.003 5/32 OD X .035 .156 .086 .035 +.004/-.002 ±10% WALL 5/32 OD X .028 .156 .100 .028 +.004/-.002 ±10% WALL 5/32 OD X.020 .156 .116 .020 +.004/-.002 ±10% WALL 5/32 OD X .015 .156 .126 .015 +.004/-.002 ±10% WALL 5/32 OD X .010 .156 .136 .010 +.004/-.002 ±10% WALL 5/32 OD X .005 .156 .146 .005 +.004/-.002 ±10% WALL 9XXX .148 .137 .0055 ±.001 ±.002 9XX* .148 .135 .0065 ±.001 ±.002 9TW* .148 .128 .010 ±.001 ±.002 9RW* .148 .118 .015 ±.001 ±.003 9HV .148 .098 .025 ±.001 ±.003 9 ½* .141 .119 .011 ±.001 ±.002 10UT .134 .122 .006 ±.001 ±.002 10XT* .134 .118 .008 ±.001 ±.002 10TW* .134 .114 .010 ±.001 ±.002 10RW* .134 .106 .014 ±.001 ±.002 10HV .134 .100 .017 ±.001 ±.002 10 ½* .126 .106 .010 ±.001 ±.002 1/8 OD X .035 .125 .055 .035 +.004/-.002 ±10% WALL 1/8 OD X .028 .125 .069 .028 +.004/-.002 ±10% WALL 1/8 OD X .020 .125 .085 .020 +.004/-.002 ±10% WALL 1/8 OD X .015 .125 .095 .015 +.004/-.002 ±10% WALL 1/8 OD X .010 .125 .105 .010 +.004/-.002 ±10% WALL 1/8 OD X .005 .125 .115 .005 +.004/-.002 ±10% WALL 11XX* .120 .112 .004 ±.001 ±.002 11X* .120 .106 .007 ±.001 ±.002 11TW* .120 .100 .010 ±.001 ±.002 11RW* .120 .094 .013 ±.001 ±.002 11HV .120 .090 .015 ±.001 ±.002 3.0 X 2.0 MM* .118 .078 .020 ±.0039 ±.0039 3.0 X 2.2 MM* .118 .086 .016 ±.0039 ±.0039 3.0 X 2.5 MM* .118 .098 .010 ±.0039 ±.0039 11 ½* .115 .0945 .0103 ±.001 ±.0015 12XX* .109 .100 .0045 ±.001 ±.001 12XT* .109 .095 .007 ±.001 ±.002 12TW* .109 .091 .009 ±.001 ±.002 12RW* .109 .085 .012 ±.001 ±.002 12H .109 .077 .016 ±.001 ±.002 12 ½* .100 .082 .009 ±.001 ±.002 13XX* .095 .090 .0025 ±.001 ±.001 13X* .095 .085 .005 ±.001 ±.001 13TW* .095 .077 .009 ±.001 ±.002 13RW* .095 .071 .012 ±.001 ±.002 13HV .095 .064 .0155 ±.001 ±.002 3/32 OD X .035 .0938 .0238 .035 ±.002 ±10% WALL 3/32 OD X .028 .0938 .0378 .028 ±.002 ±10% WALL 3/32 OD X .020 .0938 .0538 .020 ±.002 ±10% WALL 3/32 OD X .015 .0938 .0638 .015 ±.002 ±10% WALL 3/32 OD X .010 .0938 .0738 .010 ±.002 ±10% WALL 3/32 OD X .005 .0938 .0838 .005 ±.002 ±10% WALL NOMINAL TOLERANCES Gauge OD ID Wall OD ID/Wall 13 ½* .089 .071 .009 ±.001 ±.002 14XX* .083 .077 .003 ±.001 ±.001 14UT .083 .0745 .0043 ±.001 ±.0015 14XT* .083 .072 .0055 ±.001 ±.001 14TW* .083 .067 .008 ±.001 +.0015/-.001 14RW* .083 .063 .010 ±.001 ±.002 14H .083 .049 .017 ±.001 ±.002 14XH .083 .039 .022 ±.001 ±.002 14 ½* .078 .063 .0075 ±.001 ±.001 2.0 X 1.0 MM* .078 .039 .020 ±.0039 ±.0039 2.0 X 1.2 MM* .078 .047 .016 ±.0039 ±.0039 2.0 X 1.5 MM* .078 .059 .010 ±.0039 ±.0039 15XXX .072 .0695 .0012 ±.0005 ±.0005 15UT .072 .0645 .0038 ±.0005 ±.001 15XTS .072 .063 .0045 ±.0005 ±.001 15TW* .072 .060 .006 ±.0005 +.0015/-.0005 15RW* .072 .054 .009 ±.0005 ±.0015 15H .072 .050 .011 ±.0005 ±.002 15 ½* .068 .054 .007 ±.0005 ±.0015 16XX* .065 .060 .0025 ±.0005 +.001/-.0015 16UT .065 .0575 .0038 ±.0005 ±.001 16XT* .065 .055 .005 ±.0005 +.0015/-.0005 16TW* .065 .053 .006 ±.0005 +.0015/-.0005 16RW* .065 .047 .009 ±.0005 ±.0015 16H .065 .033 .016 ±.0005 ±.002 16 ½* .062 .052 .005 ±.0005 ±.0015 1/16 OD X .026 .0625 .010 .026 ±.001 ±10% WALL 1/16 OD X .025 .0625 .012 .025 ±.001 ±10% WALL 1/16 OD X .024 .0625 .014 .024 ±.001 ±10% WALL 1/16 OD X .023 .0625 .016 .023 ±.001 ±10% WALL 1/16 OD X .022 .0625 .018 .022 ±.001 ±10% WALL 1/16 OD X .021 .0625 .020 .021 ±.001 ±10% WALL 1/16 OD X .020 .0625 .022 .020 ±.001 ±10% WALL 1/16 OD X .019 .0625 .024 .019 ±.001 ±10% WALL 1/16 OD X .018 .0625 .026 .018 ±.001 ±10% WALL 1/16 OD X .017 .0625 .028 .017 ±.001 ±10% WALL 1/16 OD X .016 .0625 .030 .016 ±.001 ±10% WALL 1/16 OD X .015 .0625 .032 .015 ±.001 ±10% WALL 1/16 OD X .014 .0625 .034 .014 ±.001 ±10% WALL 1/16 OD X .013 .0625 .036 .013 ±.001 ±10% WALL 1/16 OD X .012 .0625 .038 .012 ±.001 ±10% WALL 1/16 OD X .011 .0625 .040 .011 ±.001 ±10% WALL 1/16 OD X .010 .0625 .042 .010 ±.001 ±10% WALL 1/16 OD X .009 .0625 .044 .009 ±.001 ±10% WALL 1/16 OD X .008 .0625 .046 .008 ±.001 ±10% WALL 1/16 OD X .007 .0625 .048 .007 ±.001 ±10% WALL 1/16 OD X .006 .0625 .050 .006 ±.001 ±10% WALL 1/16 OD X .005 .0625 .052 .005 ±.001 ±10% WALL 1/16 OD X .004 .0625 .054 .004 ±.001 ±.0005 WALL 1/16 OD X .003 .0625 .056 .003 ±.001 ±.0005 WALL 1/16 OD X .002 .0625 .058 .002 ±.001 ±.0005 WALL 1/16 OD X .001 .0625 .060 .001 ±.001 ±.0005 WALL 17XX* .059 .054 .0025 ±.0005 +.001/-.0005 17SP .059 .041 .009 ±.0005 ±.0015 17H .059 .039 .010 ±.0005 ±.002 17UTS .0585 .052 .0033 +.0005/-.001 ±.001 17XT* .058 .050 .004 ±.0005 ±.001 17TW* .058 .048 .005 ±.0005 +.0005/-.0015 17RW* .058 .042 .008 ±.0005 ±.0015 17 ½* .056 .046 .005 ±.0005 ±.0015 18XX* .050 .045 .0025 ±.0005 ±.001 18UTS .050 .044 .003 +.001/-.0005 +.0015/-.001 18XT* .050 .042 .004 ±.0005 ±.001 18TW* .050 .038 .006 ±.0005 +.0015/-.0005 18RW* .050 .033 .0085 ±.0005 ±.0015 NOMINAL TOLERANCES Gauge OD ID Wall OD ID/Wall 18H .050 .030 .010 ±.0005 ±.002 18 ½* .046 .034 .006 ±.0005 ±.0015 19XX* .0425 .0375 .0025 ±.0005 ±.001 19H .0425 .0225 .010 ±.0005 ±.0015 19XT* .042 .035 .0035 ±.0005 ±.001 19TW* .042 .032 .005 ±.0005 +.0015/-.0005 19RW* .042 .027 .0075 ±.0005 ±.0015 19 ½* .039 .027 .006 ±.0005 ±.0015 1.0 X 0.5 MM* .039 .019 .010 ±.0039 ±.0039 20XX* .0355 .0305 .0025 +.0005/-0 ±.001 20XT* .0355 .0275 .004 +.0005/-0 +.001/-.0005 20TW* .0355 .0255 .005 +.0005/-0 +.0015/-0 20RW* .0355 .0235 .006 +.0005/-0 +.001/-.0005 20HV .0355 .0195 .008 +.0005/-0 ±.0015 20 ½* .034 .0265 .0038 +.0005/-0 ±.001 21XX* .032 .029 .0015 +.0005/-0 +.0005/-.001 21XT* .032 .025 .0035 +.0005/-0 +.001/-.0005 21TW* .032 .023 .0045 +.0005/-0 +.001/-.0005 21RW* .032 .020 .006 +.0005/-0 +.001/-.0005 21H .032 .0165 .0078 +.0005/-0 ±.0015 1/32 OD X .008 .032 .0165 .008 ±.001 ±10% WALL 1/32 OD X .006 .032 .020 .006 ±.001 ±10% WALL 1/32 OD X .0045 .032 .023 .0045 ±.001 ±10% WALL 1/32 OD X .0035 .032 .025 .0035 ±.001 ±10% WALL 1/32 OD X .0015 .032 .029 .0015 ±.001 ±10% WALL 21 ½* .030 .024 .003 +.0005/-0 +.0005/-.001 22S .0285 .006 .0113 ±.0005 +.001/-.0005 22XX* .028 .0235 .0023 +.0005/-0 ±.0005 22XTS .028 .021 .0035 +.0005/-0 +.001/-.0005 22TW* .028 .020 .004 +.0005/-0 +.0005/-.001 22RW* .028 .016 .006 +.0005/-0 +.001/-.0005 22 ½* .026 .0205 .0028 +.0005/-0 +.0005/-.001 23HV .0255 .005 .0103 ±.0005 ±.001 23XX* .025 .020 .0025 +.0005/-0 +.001/-.0005 23TW* .025 .017 .004 +.0005/-0 +.001/-.0005 23RW* .025 .013 .006 +.0005/-0 +.001/-.0005 23 ½* .023 .0175 .0028 +.0005/-0 +.0005/-.001 24HV .0225 .005 .0088 ±.0005 +.001/-.0005 24XX* .022 .016 .003 +.0005/-0 +.001/-.0005 24TW* .022 .014 .004 +.0005/-0 +.001/-.0005 24RW* .022 .012 .005 +.0005/-0 +.001/-.0005 24 ½* .021 .0165 .0023 +.0005/-0 +.0005/-.001 25S .0205 .006 .0073 ±.0005 ±.001 25XX* .020 .016 .002 +.0005/-0 +.001/-.0005 25TW* .020 .012 .004 +.0005/-0 +.001/-.0005 25RW* .020 .010 .005 +.0005/-0 +.001/-.0005 25 ½* .019 .0145 .0023 +.0005/-0 +.0005/-.001 26S .0185 .0045 .007 ±.0005 +.001/-.0005 26XV .018 .0135 .0023 +.0005/-0 +.001/-.0005 26TW* .018 .012 .003 +.0005/-0 +.001/-.0005 26RW* .018 .010 .004 +.0005/-0 +.001/-.0005 27XV .016 .0115 .0023 +.0005/-0 +.001/-.0005 27TW* .016 .010 .003 +.0005/-0 +.001/-.0005 27RW* .016 .008 .004 +.0005/-0 +.001/-.0005 28XV .014 .0105 .0018 +.0005/-0 +.001/-.0005 28TW* .014 .009 .0025 +.0005/-0 +.001/-.0005 28RW* .014 .007 .0035 +.0005/-0 +.001/-.0005 29RW* .013 .007 .003 +.0005/-0 +.001/-.0005 30RW* .012 .006 .003 +.0005/-0 +.001/-.0005 31RW* .010 .005 .0025 +.0005/-0 +.001/-.0005 32RW* .009 .004 .0025 +.0005/-0 +.001/-.0005 33RW* .008 .004 .002 +.0005/-0 +.001/-.0005 34RW* .007 .003 .002 +.0005/-0 +.001/-.0005 35RW* .005 .002 .0015 +.0005/-0 +.001/-.0005 16.0 X 15.0 MM* .629 .591 .020 ±.0039 ±.0039 12.0 X 11.0 MM* .472 .433 .020 ±.0039 ±.0039 10.0 X 9.0 MM* .393 .354 .020 ±.0039 ±.0039 3/8 OD X .035 .375 .305 .035 +.004/-.002 ±10% WALL 3/8 OD X .028 .375 .319 .028 +.004/-.002 ±10% WALL 3/8 OD X .020 .375 .335 .020 +.004/-.002 ±10% WALL 3/8 OD X .015 .375 .345 .015 +.004/-.002 ±10% WALL 3/8 OD X .010 .375 .355 .010 +.004/-.002 ±10% WALL 8.0 X 7.0 MM* .314 .275 .020 ±.0039 ±.0039 8.0 X 7.2 MM* .314 .283 .016 ±.0039 ±.0039 8.0 X 7.5 MM* .314 .295 .010 ±.0039 ±.0039 5/16 OD X .035 .312 .242 .035 +.004/-.002 ±10% WALL 5/16 OD X .028 .312 .256 .028 +.004/-.002 ±10% WALL 5/16 OD X .020 .312 .272 .020 +.004/-.002 ±10% WALL 5/16 OD X .015 .312 .282 .015 +.004/-.002 ±10% WALL 5/16 OD X .010 .312 .292 .010 +.004/-.002 ±10% WALL 9/32 OD X .035 .281 .211 .035 +.004/-.002 ±10% WALL 9/32 OD X .028 .281 .225 .028 +.004/-.002 ±10% WALL 9/32 OD X .020 .281 .241 .020 +.004/-.002 ±10% WALL 9/32 OD X .015 .281 .251 .015 +.004/-.002 ±10% WALL 9/32 OD X .010 .281 .261 .010 +.004/-.002 ±10% WALL 9/32 OD X .005 .281 .271 .005 +.004/-.002 ±10% WALL 7.0 X 6.0 MM* .275 .236 .020 ±.0039 ±.0039 7.0 X 6.2 MM* .275 .244 .016 ±.0039 ±.0039 7.0 X 6.5 MM* .275 .255 .010 ±.0039 ±.0039 3XT* .259 .239 .010 ±.002 ±.002 3TW* .259 .229 .015 ±.002 ±.002 3RW* .259 .219 .020 ±.002 ±.003 1/4 OD X .035 .250 .180 .035 +.004/-.002 ±10% WALL 1/4 OD X .028 .250 .194 .028 +.004/-.002 ±10% WALL 1/4 OD X .020 .250 .210 .020 +.004/-.002 ±10% WALL 1/4 OD X .015 .250 .220 .015 +.004/-.002 ±10% WALL 1/4 OD X .010 .250 .230 .010 +.004/-.002 ±10% WALL 1/4 OD X .005 .250 .240 .005 +.004/-.002 ±10% WALL 3 ½* .249 .219 .015 ±.001 ±.003 4XT* .238 .218 .010 ±.002 ±.002 4TW* .238 .208 .015 ±.002 ±.002 4RW* .238 .198 .020 ±.002 ±.003 6.0 X 5.0 MM* .236 .196 .020 ±.0039 ±.0039 6.0 X 5.2 MM* .236 .204 .016 ±.0039 ±.0039 6.0 X 5.5 MM* .236 .216 .010 ±.0039 ±.0039 4 ½* .228 .198 .015 ±.001 ±.003 5XT* .219 .205 .007 ±.002 ±.002 5TW* .219 .199 .010 ±.002 ±.002 5RW* .219 .189 .015 ±.002 ±.003 7/32 OD X .035 .219 .148 .035 +.004/-.002 ±10% WALL 7/32 OD X .028 .219 .162 .028 +.004/-.002 ±10% WALL 7/32 OD X .020 .219 .178 .020 +.004/-.002 ±10% WALL 7/32 OD X .015 .219 .188 .015 +.004/-.002 ±10% WALL 7/32 OD X .010 .219 .198 .010 +.004/-.002 ±10% WALL 7/32 OD X .005 .219 .208 .005 +.004/-.002 ±10% WALL 5 ½* .211 .189 .011 ±.001 ±.003 6X* .203 .189 .007 ±.001 ±.002 6TW* .203 .183 .010 ±.001 ±.002 6RW* .203 .173 .015 ±.001 ±.003 5.0 X 4.0 MM* .196 .157 .020 ±.0039 ±.0039 5.0 X 4.2 MM* .196 .165 .016 ±.0039 ±.0039 5.0 X 4.5 MM* .196 .177 .010 ±.0039 ±.0039 6 ½* .188 .168 .010 ±.001 ±.003 3/16 OD X .035 .188 .118 .035 +.004/-.002 ±10% WALL 3/16 OD X .028 .188 .132 .028 +.004/-.002 ±10% WALL 3/16 OD X .020 .188 .148 .020 +.004/-.002 ±10% WALL 3/16 OD X .015 .188 .158 .015 +.004/-.002 ±10% WALL 3/16 OD X .010 .188 .168 .010 +.004/-.002 ±10% WALL 3/16 OD X .005 .188 .178 .005 +.004/-.002 ±10% WALL NOMINAL TOLERANCES Gauge OD ID Wall OD ID/Wall Custom sizes, special alloys and tempers are available as well as low carbon (“L” grade), domestic/DFARS compliant tubing. Vita offers short lead times on burr free cut-to-length tubing and a complete array of tubing fabrication options. We have the lowest minimums in the industry and can provide same-day shipping for all stock random lengths. Rapid delivery on most special and custom requests. If you don’t see what you need in this chart, please contact us to discuss your requirements.
-
Upload
jlbarretoa -
Category
Documents
-
view
23 -
download
3
Transcript of Vita Needle Master Tubing Chart
STAINLESS STEEL TUBINGStock sizing for all Stock Hard Temper, TIG Welded and Drawn 304 Stainless Steel Tubing— sorted by OD. (Sizes marked with an asterisk are also stocked in 316 SS.)
919 Great Plain Avenue | Needham, Massachusetts 02492Tel: 888-VITANEEDLE | Fax: 888-FAXVITA Email: [email protected]
WWW.VITANEEDLE.COM
NOMINAL TOLERANCES
Gauge OD ID Wall OD ID/Wall
7XX* .180 .173 .0035 ±.001 ±.001 7X* .180 .166 .007 ±.001 ±.0027TW* .180 .160 .010 ±.001 ±.0027RW* .180 .150 .015 ±.001 ±.0037HV .180 .131 .0245 ±.001 ±.0037 ½* .172 .150 .011 ±.001 ±.0038XXX .165 .156 .0045 ±.001 ±.0028XX* .165 .150 .0075 ±.001 ±.00258TW* .165 .145 .010 ±.001 ±.0028RW* .165 .135 .015 ±.001 ±.0038HV .165 .117 .024 ±.001 ±.0034.0 X 3.0 MM* .157 .118 .020 ±.0039 ±.00394.0 X 3.2 MM* .157 .125 .016 ±.0039 ±.00394.0 X 3.5 MM* .157 .137 .010 ±.0039 ±.00398 ½* .156 .136 .010 ±.001 ±.0035/32 OD X .035 .156 .086 .035 +.004/-.002 ±10% WALL5/32 OD X .028 .156 .100 .028 +.004/-.002 ±10% WALL5/32 OD X.020 .156 .116 .020 +.004/-.002 ±10% WALL5/32 OD X .015 .156 .126 .015 +.004/-.002 ±10% WALL5/32 OD X .010 .156 .136 .010 +.004/-.002 ±10% WALL5/32 OD X .005 .156 .146 .005 +.004/-.002 ±10% WALL9XXX .148 .137 .0055 ±.001 ±.0029XX* .148 .135 .0065 ±.001 ±.0029TW* .148 .128 .010 ±.001 ±.0029RW* .148 .118 .015 ±.001 ±.0039HV .148 .098 .025 ±.001 ±.0039 ½* .141 .119 .011 ±.001 ±.00210UT .134 .122 .006 ±.001 ±.00210XT* .134 .118 .008 ±.001 ±.00210TW* .134 .114 .010 ±.001 ±.00210RW* .134 .106 .014 ±.001 ±.00210HV .134 .100 .017 ±.001 ±.00210 ½* .126 .106 .010 ±.001 ±.0021/8 OD X .035 .125 .055 .035 +.004/-.002 ±10% WALL1/8 OD X .028 .125 .069 .028 +.004/-.002 ±10% WALL1/8 OD X .020 .125 .085 .020 +.004/-.002 ±10% WALL1/8 OD X .015 .125 .095 .015 +.004/-.002 ±10% WALL1/8 OD X .010 .125 .105 .010 +.004/-.002 ±10% WALL1/8 OD X .005 .125 .115 .005 +.004/-.002 ±10% WALL11XX* .120 .112 .004 ±.001 ±.00211X* .120 .106 .007 ±.001 ±.00211TW* .120 .100 .010 ±.001 ±.00211RW* .120 .094 .013 ±.001 ±.00211HV .120 .090 .015 ±.001 ±.0023.0 X 2.0 MM* .118 .078 .020 ±.0039 ±.00393.0 X 2.2 MM* .118 .086 .016 ±.0039 ±.00393.0 X 2.5 MM* .118 .098 .010 ±.0039 ±.003911 ½* .115 .0945 .0103 ±.001 ±.001512XX* .109 .100 .0045 ±.001 ±.00112XT* .109 .095 .007 ±.001 ±.00212TW* .109 .091 .009 ±.001 ±.00212RW* .109 .085 .012 ±.001 ±.00212H .109 .077 .016 ±.001 ±.00212 ½* .100 .082 .009 ±.001 ±.00213XX* .095 .090 .0025 ±.001 ±.00113X* .095 .085 .005 ±.001 ±.00113TW* .095 .077 .009 ±.001 ±.00213RW* .095 .071 .012 ±.001 ±.00213HV .095 .064 .0155 ±.001 ±.0023/32 OD X .035 .0938 .0238 .035 ±.002 ±10% WALL3/32 OD X .028 .0938 .0378 .028 ±.002 ±10% WALL3/32 OD X .020 .0938 .0538 .020 ±.002 ±10% WALL3/32 OD X .015 .0938 .0638 .015 ±.002 ±10% WALL3/32 OD X .010 .0938 .0738 .010 ±.002 ±10% WALL3/32 OD X .005 .0938 .0838 .005 ±.002 ±10% WALL
NOMINAL TOLERANCES
Gauge OD ID Wall OD ID/Wall
13 ½* .089 .071 .009 ±.001 ±.00214XX* .083 .077 .003 ±.001 ±.001 14UT .083 .0745 .0043 ±.001 ±.001514XT* .083 .072 .0055 ±.001 ±.00114TW* .083 .067 .008 ±.001 +.0015/-.00114RW* .083 .063 .010 ±.001 ±.00214H .083 .049 .017 ±.001 ±.00214XH .083 .039 .022 ±.001 ±.00214 ½* .078 .063 .0075 ±.001 ±.0012.0 X 1.0 MM* .078 .039 .020 ±.0039 ±.00392.0 X 1.2 MM* .078 .047 .016 ±.0039 ±.00392.0 X 1.5 MM* .078 .059 .010 ±.0039 ±.003915XXX .072 .0695 .0012 ±.0005 ±.000515UT .072 .0645 .0038 ±.0005 ±.00115XTS .072 .063 .0045 ±.0005 ±.00115TW* .072 .060 .006 ±.0005 +.0015/-.000515RW* .072 .054 .009 ±.0005 ±.001515H .072 .050 .011 ±.0005 ±.00215 ½* .068 .054 .007 ±.0005 ±.001516XX* .065 .060 .0025 ±.0005 +.001/-.001516UT .065 .0575 .0038 ±.0005 ±.00116XT* .065 .055 .005 ±.0005 +.0015/-.000516TW* .065 .053 .006 ±.0005 +.0015/-.000516RW* .065 .047 .009 ±.0005 ±.001516H .065 .033 .016 ±.0005 ±.00216 ½* .062 .052 .005 ±.0005 ±.00151/16 OD X .026 .0625 .010 .026 ±.001 ±10% WALL1/16 OD X .025 .0625 .012 .025 ±.001 ±10% WALL1/16 OD X .024 .0625 .014 .024 ±.001 ±10% WALL1/16 OD X .023 .0625 .016 .023 ±.001 ±10% WALL1/16 OD X .022 .0625 .018 .022 ±.001 ±10% WALL1/16 OD X .021 .0625 .020 .021 ±.001 ±10% WALL1/16 OD X .020 .0625 .022 .020 ±.001 ±10% WALL1/16 OD X .019 .0625 .024 .019 ±.001 ±10% WALL1/16 OD X .018 .0625 .026 .018 ±.001 ±10% WALL1/16 OD X .017 .0625 .028 .017 ±.001 ±10% WALL1/16 OD X .016 .0625 .030 .016 ±.001 ±10% WALL1/16 OD X .015 .0625 .032 .015 ±.001 ±10% WALL1/16 OD X .014 .0625 .034 .014 ±.001 ±10% WALL1/16 OD X .013 .0625 .036 .013 ±.001 ±10% WALL1/16 OD X .012 .0625 .038 .012 ±.001 ±10% WALL1/16 OD X .011 .0625 .040 .011 ±.001 ±10% WALL1/16 OD X .010 .0625 .042 .010 ±.001 ±10% WALL1/16 OD X .009 .0625 .044 .009 ±.001 ±10% WALL1/16 OD X .008 .0625 .046 .008 ±.001 ±10% WALL1/16 OD X .007 .0625 .048 .007 ±.001 ±10% WALL1/16 OD X .006 .0625 .050 .006 ±.001 ±10% WALL1/16 OD X .005 .0625 .052 .005 ±.001 ±10% WALL1/16 OD X .004 .0625 .054 .004 ±.001 ±.0005 WALL1/16 OD X .003 .0625 .056 .003 ±.001 ±.0005 WALL1/16 OD X .002 .0625 .058 .002 ±.001 ±.0005 WALL1/16 OD X .001 .0625 .060 .001 ±.001 ±.0005 WALL17XX* .059 .054 .0025 ±.0005 +.001/-.000517SP .059 .041 .009 ±.0005 ±.001517H .059 .039 .010 ±.0005 ±.00217UTS .0585 .052 .0033 +.0005/-.001 ±.00117XT* .058 .050 .004 ±.0005 ±.00117TW* .058 .048 .005 ±.0005 +.0005/-.001517RW* .058 .042 .008 ±.0005 ±.001517 ½* .056 .046 .005 ±.0005 ±.001518XX* .050 .045 .0025 ±.0005 ±.00118UTS .050 .044 .003 +.001/-.0005 +.0015/-.00118XT* .050 .042 .004 ±.0005 ±.00118TW* .050 .038 .006 ±.0005 +.0015/-.000518RW* .050 .033 .0085 ±.0005 ±.0015
NOMINAL TOLERANCES
Gauge OD ID Wall OD ID/Wall
18H .050 .030 .010 ±.0005 ±.00218 ½* .046 .034 .006 ±.0005 ±.001519XX* .0425 .0375 .0025 ±.0005 ±.001 19H .0425 .0225 .010 ±.0005 ±.001519XT* .042 .035 .0035 ±.0005 ±.00119TW* .042 .032 .005 ±.0005 +.0015/-.000519RW* .042 .027 .0075 ±.0005 ±.001519 ½* .039 .027 .006 ±.0005 ±.00151.0 X 0.5 MM* .039 .019 .010 ±.0039 ±.003920XX* .0355 .0305 .0025 +.0005/-0 ±.00120XT* .0355 .0275 .004 +.0005/-0 +.001/-.000520TW* .0355 .0255 .005 +.0005/-0 +.0015/-020RW* .0355 .0235 .006 +.0005/-0 +.001/-.000520HV .0355 .0195 .008 +.0005/-0 ±.001520 ½* .034 .0265 .0038 +.0005/-0 ±.00121XX* .032 .029 .0015 +.0005/-0 +.0005/-.00121XT* .032 .025 .0035 +.0005/-0 +.001/-.000521TW* .032 .023 .0045 +.0005/-0 +.001/-.000521RW* .032 .020 .006 +.0005/-0 +.001/-.000521H .032 .0165 .0078 +.0005/-0 ±.00151/32 OD X .008 .032 .0165 .008 ±.001 ±10% WALL1/32 OD X .006 .032 .020 .006 ±.001 ±10% WALL1/32 OD X .0045 .032 .023 .0045 ±.001 ±10% WALL1/32 OD X .0035 .032 .025 .0035 ±.001 ±10% WALL1/32 OD X .0015 .032 .029 .0015 ±.001 ±10% WALL21 ½* .030 .024 .003 +.0005/-0 +.0005/-.00122S .0285 .006 .0113 ±.0005 +.001/-.000522XX* .028 .0235 .0023 +.0005/-0 ±.000522XTS .028 .021 .0035 +.0005/-0 +.001/-.000522TW* .028 .020 .004 +.0005/-0 +.0005/-.00122RW* .028 .016 .006 +.0005/-0 +.001/-.000522 ½* .026 .0205 .0028 +.0005/-0 +.0005/-.00123HV .0255 .005 .0103 ±.0005 ±.00123XX* .025 .020 .0025 +.0005/-0 +.001/-.000523TW* .025 .017 .004 +.0005/-0 +.001/-.000523RW* .025 .013 .006 +.0005/-0 +.001/-.000523 ½* .023 .0175 .0028 +.0005/-0 +.0005/-.00124HV .0225 .005 .0088 ±.0005 +.001/-.000524XX* .022 .016 .003 +.0005/-0 +.001/-.000524TW* .022 .014 .004 +.0005/-0 +.001/-.000524RW* .022 .012 .005 +.0005/-0 +.001/-.000524 ½* .021 .0165 .0023 +.0005/-0 +.0005/-.00125S .0205 .006 .0073 ±.0005 ±.00125XX* .020 .016 .002 +.0005/-0 +.001/-.000525TW* .020 .012 .004 +.0005/-0 +.001/-.000525RW* .020 .010 .005 +.0005/-0 +.001/-.000525 ½* .019 .0145 .0023 +.0005/-0 +.0005/-.00126S .0185 .0045 .007 ±.0005 +.001/-.000526XV .018 .0135 .0023 +.0005/-0 +.001/-.000526TW* .018 .012 .003 +.0005/-0 +.001/-.000526RW* .018 .010 .004 +.0005/-0 +.001/-.000527XV .016 .0115 .0023 +.0005/-0 +.001/-.000527TW* .016 .010 .003 +.0005/-0 +.001/-.000527RW* .016 .008 .004 +.0005/-0 +.001/-.000528XV .014 .0105 .0018 +.0005/-0 +.001/-.000528TW* .014 .009 .0025 +.0005/-0 +.001/-.000528RW* .014 .007 .0035 +.0005/-0 +.001/-.000529RW* .013 .007 .003 +.0005/-0 +.001/-.000530RW* .012 .006 .003 +.0005/-0 +.001/-.000531RW* .010 .005 .0025 +.0005/-0 +.001/-.000532RW* .009 .004 .0025 +.0005/-0 +.001/-.000533RW* .008 .004 .002 +.0005/-0 +.001/-.000534RW* .007 .003 .002 +.0005/-0 +.001/-.000535RW* .005 .002 .0015 +.0005/-0 +.001/-.0005
16.0 X 15.0 MM* .629 .591 .020 ±.0039 ±.003912.0 X 11.0 MM* .472 .433 .020 ±.0039 ±.003910.0 X 9.0 MM* .393 .354 .020 ±.0039 ±.00393/8 OD X .035 .375 .305 .035 +.004/-.002 ±10% WALL3/8 OD X .028 .375 .319 .028 +.004/-.002 ±10% WALL3/8 OD X .020 .375 .335 .020 +.004/-.002 ±10% WALL3/8 OD X .015 .375 .345 .015 +.004/-.002 ±10% WALL3/8 OD X .010 .375 .355 .010 +.004/-.002 ±10% WALL8.0 X 7.0 MM* .314 .275 .020 ±.0039 ±.00398.0 X 7.2 MM* .314 .283 .016 ±.0039 ±.00398.0 X 7.5 MM* .314 .295 .010 ±.0039 ±.00395/16 OD X .035 .312 .242 .035 +.004/-.002 ±10% WALL5/16 OD X .028 .312 .256 .028 +.004/-.002 ±10% WALL5/16 OD X .020 .312 .272 .020 +.004/-.002 ±10% WALL5/16 OD X .015 .312 .282 .015 +.004/-.002 ±10% WALL5/16 OD X .010 .312 .292 .010 +.004/-.002 ±10% WALL9/32 OD X .035 .281 .211 .035 +.004/-.002 ±10% WALL9/32 OD X .028 .281 .225 .028 +.004/-.002 ±10% WALL9/32 OD X .020 .281 .241 .020 +.004/-.002 ±10% WALL9/32 OD X .015 .281 .251 .015 +.004/-.002 ±10% WALL9/32 OD X .010 .281 .261 .010 +.004/-.002 ±10% WALL9/32 OD X .005 .281 .271 .005 +.004/-.002 ±10% WALL7.0 X 6.0 MM* .275 .236 .020 ±.0039 ±.00397.0 X 6.2 MM* .275 .244 .016 ±.0039 ±.00397.0 X 6.5 MM* .275 .255 .010 ±.0039 ±.00393XT* .259 .239 .010 ±.002 ±.0023TW* .259 .229 .015 ±.002 ±.0023RW* .259 .219 .020 ±.002 ±.0031/4 OD X .035 .250 .180 .035 +.004/-.002 ±10% WALL1/4 OD X .028 .250 .194 .028 +.004/-.002 ±10% WALL1/4 OD X .020 .250 .210 .020 +.004/-.002 ±10% WALL1/4 OD X .015 .250 .220 .015 +.004/-.002 ±10% WALL1/4 OD X .010 .250 .230 .010 +.004/-.002 ±10% WALL1/4 OD X .005 .250 .240 .005 +.004/-.002 ±10% WALL3 ½* .249 .219 .015 ±.001 ±.0034XT* .238 .218 .010 ±.002 ±.0024TW* .238 .208 .015 ±.002 ±.0024RW* .238 .198 .020 ±.002 ±.0036.0 X 5.0 MM* .236 .196 .020 ±.0039 ±.00396.0 X 5.2 MM* .236 .204 .016 ±.0039 ±.00396.0 X 5.5 MM* .236 .216 .010 ±.0039 ±.00394 ½* .228 .198 .015 ±.001 ±.0035XT* .219 .205 .007 ±.002 ±.0025TW* .219 .199 .010 ±.002 ±.0025RW* .219 .189 .015 ±.002 ±.0037/32 OD X .035 .219 .148 .035 +.004/-.002 ±10% WALL7/32 OD X .028 .219 .162 .028 +.004/-.002 ±10% WALL7/32 OD X .020 .219 .178 .020 +.004/-.002 ±10% WALL7/32 OD X .015 .219 .188 .015 +.004/-.002 ±10% WALL7/32 OD X .010 .219 .198 .010 +.004/-.002 ±10% WALL7/32 OD X .005 .219 .208 .005 +.004/-.002 ±10% WALL5 ½* .211 .189 .011 ±.001 ±.0036X* .203 .189 .007 ±.001 ±.0026TW* .203 .183 .010 ±.001 ±.0026RW* .203 .173 .015 ±.001 ±.0035.0 X 4.0 MM* .196 .157 .020 ±.0039 ±.00395.0 X 4.2 MM* .196 .165 .016 ±.0039 ±.00395.0 X 4.5 MM* .196 .177 .010 ±.0039 ±.00396 ½* .188 .168 .010 ±.001 ±.0033/16 OD X .035 .188 .118 .035 +.004/-.002 ±10% WALL3/16 OD X .028 .188 .132 .028 +.004/-.002 ±10% WALL3/16 OD X .020 .188 .148 .020 +.004/-.002 ±10% WALL3/16 OD X .015 .188 .158 .015 +.004/-.002 ±10% WALL3/16 OD X .010 .188 .168 .010 +.004/-.002 ±10% WALL3/16 OD X .005 .188 .178 .005 +.004/-.002 ±10% WALL
NOMINAL TOLERANCES
Gauge OD ID Wall OD ID/Wall
Custom sizes, special alloys and tempers are available as well as low carbon (“L” grade), domestic/DFARS compliant tubing. Vita offers short lead times on burr free cut-to-length tubing and a complete array of tubing fabrication options.
We have the lowest minimums in the industry and can provide same-day shipping for all stock random lengths. Rapid delivery on most special and custom requests. If you don’t see what you need in this chart, please contact us to discuss your requirements.
