View 9009A Spec Sheet
Transcript of View 9009A Spec Sheet
-
All height-of-cut adjustments on the
9009A can be performed without tools
with an innovative notch system. All it
takes is a simple pull of a lever.
Our unique rear deck design allows
for greater clippings dispersion and
the deeper shell stands grass up for
an even cut.
Passcode-protected TechControl display
lets you precisely set mowing speed,
turning speed, or transport speed for
consistent performance.
The double yoke on the 9009A means
the rotary decks follow the contours
in the most undulating terrain for an
exceptional quality and consistency
of cut.
Its not about mowing wider in the rough. Its about mowing wide better.
Introducing the new 9009A TerrainCut mowerUntil now, using a wide area mower in the rough meant compromising on your quality of cut. But with our new 9009A TerrainCut mower, you can maximize both your productivity and your cut quality.
With a 108-inch/9-foot cutting width, the 9009A is a fve-gang, 27-inch (68.58 cm) independent rotary deck mower. A double-point yoke system on all fve decks increases deck movement fore and aft, allowing for greater contour following and an even cut. And the 9009A has a greater deck overlap for superior side hill mowing.
The 9009A also sports a deeper deck design with a rear discharge for greater dispersion and a cleaner cut. And our exclusive LoadMatch lets you mow in thick, lush conditions. And the 9009A features the same TechControl display found on our A-Model mowers. The TechControl lets you set precise mow, transport, and turn speeds while also allowing for quick and easy diagnostics.
-
Engine
Type Direct Inject Turbocharged Diesel B20 compliant
Compliant emission regulation United States/Canada Tier 4; EU over 37.28 kW
Maximum rated horsepower (kW) 55.1 @ 2800 rpm ISOC hp (41.1 @ 2800 rpm ISOC kW)
Cylinders 4
Displacement 2.091 L 127.60 cu in.
Air cleaner 2-stage dry element
Fuel Diesel
Cooling system Liquid centrifugal pump; forward machine location for optimum cooling
Vehicle
Traction type eHydro servo controlled hydraulic traction pump
Deck drive pump Tandem gear pump
Deck drive Direct-coupled hydraulic gear motor
Hydrostatic system capacity, U.S. gal. (L) 45.4 L 12 U.S. gal.
Fuel tank capacity, U.S. gal. (L) 60.6 L 16 U.S. gal.
Steering Hydraulic power with dual rod, double acting steering cylinder
Steering tires 20x12-10 4PR Turf
Front drive tires 26.5x14-12 6PR Ultra Trac
Ground pressure 12-18 psi
Brakes Internal hydraulic wet disc brakes with dynamic braking through closed loop hydrostatic system
Operating Weight Wet (cutting units raised), lb. (kg) 4000 lb (1,814.37 kg)
Options available Canopy, mulch blade, high lift blade, rear roller scraper
Controls
Throttle No throttle lever; Automatic controls with AutoPedal foot controls; manual control through TechControl display
Forward/reverse 2-pedal
Mower lift One-touch single handle
Parking brake Electric Switch on Command Arm for Internal Wet Disk Brakes
Seat Air Ride Suspension seat with seat belts and arm rest; fore/aft adjustment; weight and lumbar adjustment
PTO Electric Switch on Command Arm for quick and easy transition from mow to transport
Brakes Electric Switch on Command Arm for Internal Wet Disk Brakes
ROPS Standard, meets ISO 21299 standards
Tilt steering Left Foot operated for easy adjustment
Operator display
TechControl Display: Located on Command Arm; displays machine warnings, on-board electrical diagnostics; service
timers on large easy to read screen; quick on the go settings for mow and transport speed; Turn Speed; Loadmatch
and ON/OFF Weight Transfer and Cruise Control Use selection:; Cutting unit drop rate adjustment; all settings are
pass code protected
Dimension
Height with ROPS 87.4 in. (2220 mm)
Length 134 in. (3393 mm)
Transport width 90 in. (2287 mm) @ 4 in. (101.60 mm) height of cut
Mowing width 9 Feet; 108 in. (2.74 m) 6.75 in. (17.15 cm) overlap
Ground speeds ---
Mowing, mph (km/h) 0 to 8.0 mph (0 to 12.8 km/h)
Transport, mph (km/h) 0 to 12.5 mph (0 to 20.12 km/h)
Reverse, mph (km/h) 0 to 5 mph (0 to 6.4 km/h)
Cutting Units
Cutting deck width, in. (cm) 27 in. (68.58 cm)
Height of cut range, in. (cm) .75 - 4 in. (1.91 to 10.2 cm); no tool adjustment
Deck constructionSingle 10-gauge steel stamped deck with front skid plate 1.5 in. (38mm) tall and .5 in. (12.7mm) thick steel stock
welded to the decks edge.Blade tip speed, ft./min. (m/min) 16,097 ft./min. (409 m/min.)
Rear roller diameter, in. (cm) 3 in. (7.62 cm)
Front rollers, in. (cm) 5 in. (12.70 cm)
Fuel Economy
Actual fuel usage will vary depending on course
conditions, operation, turf and fuel quality
25% load 3.63 Liters per hour (.96 GPH) 40% Load 5.64 Liters per hour (1.49 GPH) 50% Load 6.85 liters per hour
(1.81 GPH)
Warranty
Type Two-year limited
Certifcation
Type ANSI B71.4-2012.; CE
Sound Levels
Attachments installed ---
Measuring standard ISO 11201
Operator ear full engine rpm, dB(A) 91 dBA
Operator ear reduced engine rpm (2300 rpm)dB(A) ---
9009A TerrainCut Rough Mower
DSTE63697 (15-12)
Product features are based on published information at the time of publication and are subject to change without notice. All trademarked terms, including John Deere, the leaping deer symbol and the colors green and yellow used herein are the property of Deere & Company, unless otherwise noted. Availability of products, product features, and other content on this site may vary by model and geographic region. Engine horsepower and torque information for non-Deere engines are provided by the engine manufacturer for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer's Web site for additional information.