VIDEO CASSETTE RECORDER HR-VP650U (Hi-Fi) HR...

HR-VP650U (Hi-Fi)

HR-VP450U (Monaural)

VIDEO CASSETTE RECORDER

INSTRUCTIONS

LPT0008-001C

For Customer Use:Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference. Model No. Serial No.

CH

MENUVIDEO (MONO)L–AUDIO–R

STOP/EJECT PAUSEREC

REW FFPLAYPOWER

OKSP

VCR

TV CH +

TV

V

OL –

TV CH –

TVVO

L+

TV

CANCEL TIMER

START STOP DATE

PLAYREW

REC STOP

SHUTTLEPLUS

PAUSE

FF

MENU OK

CH

POWER

TV/VCR

C.RESET

DAILY(M-F)

AUX

WEEKLY

PROGCHECK

PROG SP/EP SKIP SEARCH

DISPLAYENTER/OSD

CABLE/DBS

1 2 3

4 5 6

7 8 9

0

2

4

1

3

EXPRESS PROGRAMMING

MULTI BRANDREMOTE CONTROL UNIT

MBRSETA/B

The VCR illustrations appearing in this instruction manual are of the HR-VP650U.

2 EN

Dear Customer,Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautionscontained in the following pages to ensure safe use of your new VCR.

CAUTIONS

WARNING:TO PREVENT FIRE OR SHOCKHAZARD, DO NOT EXPOSE THISUNIT TO RAIN OR MOISTURE.CAUTION:This video cassette recorder should be used with AC120V`, 60Hz only.To prevent electric shocks and fire hazards, DO NOT useany other power source.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDEBLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRELA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNECORRESPONDANTE DE LA PRISE ET POUSSERJUSQU'AU FOND.

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Failure to heed the following precautions may result indamage to the VCR, remote control or video cassette.1. DO NOT place the VCR . . .

... in an environment prone to extreme temperatures orhumidity.

... in direct sunlight.

... in a dusty environment.

... in an environment where strong magnetic fields aregenerated.

... on a surface that is unstable or subject to vibration.2. DO NOT block the VCR’s ventilation openings.3. DO NOT place heavy objects on the VCR or remote control.4. DO NOT place anything which might spill on top of the

VCR or remote control.5. AVOID violent shocks to the VCR during transport.

**MOISTURE CONDENSATIONMoisture in the air will condense on the VCR when you move itfrom a cold place to a warm place, or under extremely humidconditions—just as water droplets form on the surface of a glassfilled with cold liquid. Moisture condensation on the head drumwill cause damage to the tape. In conditions where condensa-tion may occur, keep the VCR’s power turned on for a fewhours to let the moisture dry before inserting a tape.

**ABOUT HEAD CLEANINGAccumulation of dirt and other particles on the video headsmay cause the playback picture to become blurred or inter-rupted. Be sure to contact your nearest JVC dealer if suchtroubles occur.

Note to CATV system installer:This reminder is provided to call the CATV systeminstaller's attention to Article 820-40 of the NEC thatprovides guidelines for proper grounding and, in particular,specifies that the cable ground shall be connected to thegrounding system of the building, as close to the point ofcable entry as practical.

CAUTION:Changes or modifications not approved by JVC could voiduser's authority to operate the equipment.

n Cassettes marked "VHS" (or "S-VHS") can be used with thisvideo cassette recorder. However, S-VHS recording is notpossible with this model.

n This model is equipped with SQPB (S-VHS QUASI PLAY-BACK) that makes it possible to play back S-VHS recordingswith regular VHS resolution.

n HQ VHS is compatible with existing VHS equipment.n As an ENERGY STAR® Partner, JVC has determined that this

product or product model meets the ENERGY STAR® guidelinesfor energy efficiency.

VCR Plus+ and PlusCode are trademarks of Gemstar DevelopmentCorporation.The VCR Plus+ system is manufactured under license fromGemstar Development Corporation.

DSSTM is an official trademark of DIRECTV, Inc., a unit of GMHughes Electronics. PRIMESTAR is a registered service mark ofPrimestar Partners, L.P. DISH NetworkTM is a trademark ofEchostar Communications Corporation.

MOVIE ADVANCETM is a trademark of SRT, Inc. A Jerry Igguldeninvention licensed in association with Arthur D. Little Enter-prises, Inc. (HR-VP650U only)

EN 3IMPORTANT PRODUCTSAFETY INSTRUCTIONSElectrical energy can perform many useful functions. Butimproper use can result in potential electrical shock or firehazards. This product has been engineered and manufacturedto assure your personal safety. In order not to defeat the built-insafeguards, observe the following basic rules for its installation,use and servicing.

ATTENTION:Follow and obey all warnings and instructions marked on yourproduct and its operating instructions. For your safety, pleaseread all the safety and operating instructions before you operatethis product and keep this booklet for future reference.

INSTALLATION1. Grounding or Polarization(A) Your product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than theother). This plug will fit into the power outlet only one way.This is a safety feature.If you are unable to insert the plug fully into the outlet, tryreversing the plug. If the plug should still fail to fit, contactyour electrician to replace your obsolete outlet. Do notdefeat the safety purpose of the polarized plug.

(B) Your product may be equipped with a 3-wire grounding-typeplug, a plug having a third (grounding) pin. This plug willonly fit into a grounding-type power outlet. This is a safetyfeature.If you are unable to insert the plug into the outlet, contactyour electrician to replace your obsolete outlet. Do notdefeat the safety purpose of the grounding-type plug.

2. Power SourcesOperate your product only from the type of power sourceindicated on the marking label. If you are not sure of the type ofpower supply to your home, consult your product dealer orlocal power company. If your product is intended to operatefrom battery power, or other sources, refer to the operatinginstructions.

3. OverloadingDo not overload wall outlets, extension cords, or integralconvenience receptacles as this can result in a risk of fire orelectric shock.

4. Power Cord ProtectionPower supply cords should be routed so that they are not likelyto be walked on or pinched by items placed upon or againstthem, paying particular attention to cords at plugs, conveniencereceptacles, and the point where they exit from the product.

5. VentilationSlots and openings in the cabinet are provided for ventilation.To ensure reliable operation of the product and to protect itfrom overheating, these openings must not be blocked orcovered.• Do not block the openings by placing the product on a bed,

sofa, rug or other similar surface.• Do not place the product in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or themanufacturer’s instructions have been adhered to.

6. Wall or Ceiling MountingThe product should be mounted to a wall or ceiling only asrecommended by the manufacturer.

ANTENNALEAD IN WIRE

ANTENNADISCHARGE UNIT(NEC SECTION 810-20)

GROUNDING CONDUCTORS(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM(NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC SERVICEEQUIPMENT

EXAMPLE OF ANTENNA GROUNDING AS PERNATIONAL ELECTRICAL CODE, ANSI/NFPA 70

GROUND CLAMP

ANTENNA INSTALLATIONINSTRUCTIONS1. Outdoor Antenna GroundingIf an outside antenna or cable system is connected to theproduct, be sure the antenna or cable system is grounded so asto provide some protection against voltage surges and built-upstatic charges. Article 810 of the National Electrical Code,ANSI/NFPA 70, provides information with regard to propergrounding of the mast and supporting structure, grounding ofthe lead-in wire to an antenna discharge unit, size of groundingconnectors, location of antenna discharge unit, connection togrounding electrodes, and requirements for the groundingelectrode.

2. LightningFor added protection for this product during a lightning storm,or when it is left unattended and unused for long periods oftime, unplug it from the wall outlet and disconnect the antennaor cable system. This will prevent damage to the product due tolightning and power-line surges.

3. Power LinesAn outside antenna system should not be located in the vicinityof overhead power lines or other electric light or power circuits,or where it can fall into such power lines or circuits. Wheninstalling an outside antenna system, extreme care should betaken to keep from touching such power lines or circuits ascontact with them might be fatal.

4 EN

SERVICING1. ServicingIf your product is not operating correctly or exhibits a markedchange in performance and you are unable to restore normaloperation by following the detailed procedure in its operatinginstructions, do not attempt to service it yourself as opening orremoving covers may expose you to dangerous voltage or otherhazards. Refer all servicing to qualified service personnel.

2. Damage Requiring ServiceUnplug this product from the wall outlet and refer servicing toqualified service personnel under the following conditions:a.When the power supply cord or plug is damaged.b.If liquid has been spilled, or objects have fallen into the

product.c. If the product has been exposed to rain or water.d.If the product does not operate normally by following the

operating instructions. Adjust only those controls that arecovered by the operating instructions as an improperadjustment of other controls may result in damage and willoften require extensive work by a qualified technician torestore the product to its normal operation.

e. If the product has been dropped or damaged in any way.f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement PartsWhen replacement parts are required, be sure the servicetechnician has used replacement parts specified by themanufacturer or have the same characteristics as the originalpart. Unauthorized substitutions may result in fire, electricshock or other hazards.

4. Safety CheckUpon completion of any service or repairs to this product, askthe service technician to perform safety checks to determinethat the product is in safe operating condition.

HOW TO USE THIS INSTRUCTIONMANUAL● All major sections and subsections are listed in the Table Of

Contents on page 5. Use this when searching for informationon a specific procedure or feature.

● The Index on pages 48–51 lists frequently-used terms, andthe number of the page on which they are used or explainedin the manual. This section also illustrates the controls andconnections on the front and rear panel, the front displaypanel and the remote control.

● The Z mark signals a reference to another page forinstructions or related information.

● Operation buttons necessary for the various procedures areclearly indicated through the use of illustrations at thebeginning of each major section.

BEFORE YOU INSTALL YOUR NEWVCR . . .. . . please read the sections/literature listed below.● ”Cautions” on page 2● ”Important Products Safety Instructions” on the previous pages

USE1. AccessoriesTo avoid personal injury:• Do not place this product on an unstable cart, stand, tripod,

bracket, or table. It may fall, causing serious injury to a childor adult, and serious damage to the product.

• Use only with a cart, stand, tripod, bracket, or tablerecommended by the manufacturer or sold with the product.

• Use a mounting accessory recommended by themanufacturer and follow the manufacturer’s instructions forany mounting of the product.

• Do not try to roll a cart with small casters across thresholds ordeep-pile carpets.

2. Product and Cart CombinationA product and cart combinationshould be moved with care. Quickstops, excessive force, and unevensurfaces may cause the product andcart combination to overturn.

3. Water and MoistureDo not use this product near water—for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement,or near a swimming pool and the like.

4. Object and Liquid EntryNever push objects of any kind into this product throughopenings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spillliquid of any kind on the product.

5. AttachmentsDo not use attachments not recommended by the manufacturerof this product as they may cause hazards.

6. CleaningUnplug this product from the wall outlet before cleaning. Donot use liquid cleaners or aerosol cleaners. Use a damp clothfor cleaning.

7. HeatThe product should be situated away from heat sources such asradiators, heat registers, stoves, or other products (includingamplifiers) that produce heat.

PORTABLE CART WARNING(Symbol provided by RETAC)

EN 5CONTENTS

EDITING 39Edit To Another VCR ....................................39Edit From A Camcorder Or Another VCR ......40

SPECIAL FEATURES 41TV Multi-Brand Remote Control ..............................41Cable Box Multi-Brand Remote Control ...................42DBS Receiver Multi-Brand Remote Control ..............43Control Two JVC VCRs ............................................44

TROUBLESHOOTING 45Power ........................................................ 45Tape Transport ............................................45Playback .................................................... 45Recording ................................................... 45Timer Recording ..........................................46Other Problems ..........................................46

QUESTIONS AND ANSWERS 47Playback .................................................... 47Recording ................................................... 47Timer Recording ..........................................47

INDEX 48List Of Terms ............................................... 48Front View.................................................. 49Rear View .................................................. 50Front Display Panel .....................................50Remote Control ...........................................51

S PECIFICATIONS 52

FOR SERVICING (Only in U.S.A.) 53

WARRANTY (Only in U.S.A.) 54

INSTALLING YOUR NEW VCR 6Basic Connections ..................................6

INITIAL SETTINGS 8Plug & Play .................................................. 8Language ................................................... 10Clock .......................................................... 11

Preparation .............................................................. 11Semi-Auto................................................................12Manual ....................................................................13

Tuner .......................................................... 14Set Receivable Channels ..........................................14Add Or Delete A Channel ........................................15

SIMPLE PLAYBACK ANDRECORDING 16

Simple Playback ......................................... 16Simple Recording ........................................ 17

PLAYBACK AND RECORDINGFEATURES 18

Playback Features ......................................18Still Picture/Frame-By-Frame Playback.....................18Slow Motion/Reverse Slow Motion ..........................18Variable-Speed Search/Reverse Motion Playback .....18High-Speed Search ..................................................19Skip Search ..............................................................19Index Search ............................................................19Instant ReView .........................................................20Manual Tracking ......................................................20Video Stabilizer .......................................................21Repeat Playback ......................................................22Counter Reset ..........................................................22Tape Position Indicator ............................................22Next-Function Memory............................................22Superimpose ............................................................23Select The Soundtrack (HR-VP650U only) ...............24Movie Advance (HR-VP650U only) .........................25

Auto Picture ................................................26Preparation ..............................................................26Playback ..................................................................27

Recording Features .....................................28Record One Program WhileWatching Another ....................................................28Display Elapsed Recording Time ..............................28Stereo And SAP (Second Audio Program)(HR-VP650U only) ...................................................29To Record SAP Programs (HR-VP650U only) ...........29

TIMER RECORDING 30VCR Plus+ Timer Programming....................30VCR Plus+ Setup ......................................... 32Express Timer Programming .......................34

Check, Cancel And Revise Programs .......................36Auto SP→EP Timer ..................................................37Auto Timer ...............................................................37

Instant Timer Recording (ITR) .......................38

6 EN

ANT. IN

RF OUT

CH3 CH4

OUT

R

L

AUDIO

VIDEO

Basic Connections

INSTALLING YOUR NEW VCR

RF OUT

ANT. IN(Antenna or Cable input)

75 ohm terminal

Back of VCR

Antenna or Cable

Coaxial Cable

Flat Feeder

Matching Transformer(not supplied)

AC PowerCord

Back of VCR

AC Outlet

RF Cable(supplied)

Audio/Video Cable(not supplied)

TV

CH3 CH4

EN 7CHECK CONTENTS

1 Make sure the package contains all of the accessorieslisted in “SPECIFICATIONS” (Z pg. 52).

SITUATE VCR

2 Place the VCR on a stable, horizontal surface.

CONNECT VCR TO TV

3 The connection method you use depends on the type ofTV you have.

RF Connection● To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV antenna from the TV.b– Connect the TV antenna cable to the ANT. IN jack

on the rear of the VCR.c– Connect the supplied RF cable between the RF

OUT jack on the rear of the VCR and the TV’santenna terminal. Set TV on CH3 or CH4corresponding to the CH3 – CH4 switch setting onthe back of the VCR.

AV Connection● To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown inthe illustration.

b– Connect an Audio/Video Cable between the AUDIOOUT and VIDEO OUT jacks on the rear of the VCRand the AV IN jacks on the TV. Set your TV in videoinput mode or A/V input mode. Refer to the TVInstruction Manual.

For HR-VP450U Owners:If your TV has AUDIO IN L and R connectors, connectthe VCR to the L connector.

CONNECT VCR TOPOWER SOURCE

4 Connect the power plug to an AC outlet.

● The clock and tuner channels will automatically beset when the antenna is connected and when the ACis first connected to the VCR (Z pg. 8).(If "Auto" or "CH" is displayed on the front displaypanel before the VCR is powered on, the clock andtuner channels are being set automatically. Wait forthe time to be displayed on the front display panelbefore powering on the VCR.)

FINAL PREPARATION FORUSE

5 Power on the VCR and select the VCR channel (3 or 4)by setting the switch on the rear of the VCR as shown inthe illustration.You can now perform simple playback (Z pg. 16) orsimple recording (Z pg. 17).

NOTES:● The VCR channel is the channel on the TV which will display

the audio and video signals from the VCR. The VCR's CH3-CH4 switch, on the back of the VCR, sets the VCR channel toCH3 or CH4.

● The CH3–CH4 switch is preset to the CH3 position.Set to CH4 if CH3 is used for broadcasting in your area andset the channel on the TV to correspond to the VCR's CH3–CH4 switch setting.

● If RF connection to TV is used, when switching from VCR to TVmode and from TV to VCR it may be necessary to issue a CH UPand then CH DOWN on TV to obtain a good quality picture.

● Even if you are using AV cables to connect your VCR to yourTV, you must also connect it using the RF cable. This willensure that you can record one show while watching another(Z pg. 28).

● For full identification of the VCR's rear panel, refer to theIndex (REAR VIEW Z pg. 50).

8 EN INITIAL SETTINGS

Plug & PlayThe Plug & Play function sets the clock and tuner channelsautomatically when power is first connected to the VCR. Theantenna cable must be connected for the Plug & Play function.

The time and date can be set automatically from clock settingdata that is transmitted by one of the regular TV broadcastchannels. We call this TV channel the “Host Channel” and it isa PBS channel in your area.

PLUG & PLAY SETUP

1 Connect the antenna cable to the VCR (Z pg. 6). Thenconnect the VCR’s power plug to an AC outlet. Do notpower on the VCR. The clock and tuner channels willbe set automatically.

NOTES:● Auto clock set is performed first. The auto clock set

function scans all the channels received by your VCRto find the Host Channel and then sets the clock."Auto" blinks on the front display panel during Autoclock set.

● Auto channel set is performed next. The auto channelset function scans all the channels that are receivableby your VCR. It then automatically assigns eachreceivable channels to the CH5∞ (+/–) buttons. Itskips non-receivable channels. During auto channelset the channel numbers are displayed as they arescanned and set.

● When Plug & Play has been completed successfully thecorrect time is displayed.

● If an incorrect time or "– –:– –" appears on the displaypanel, see "What To Do If Plug & Play Has Failed" onnext page.

Auto Clock Set/Auto Tuner Set

IMPORTANT● Don’t press any buttons on the VCR or remote while

Plug & Play is in progress.● If you perform Plug & Play successfully, there’s no need to

perform the Clock (Z pg. 11) and Tuner (Z pg. 14)procedures. If, however, you want to add or deletechannels, refer to “Add Or Delete A Channel” on page 15.

During Initial Auto Clock Set"Auto" blinks.

During Auto Channel SetThe channel numbers are displayedas they are scanned and set.

Plug & Play CompletedThe current time (includingAM/PM) is displayed.

* If an incorrect time or "– –:– –" appears on the display panel, see "What To Do If Plug & Play Has Failed" on next page.

ATTENTIONIf you use a cable box, Plug & Play will not function; setthe clock and tuner channels manually. (Z pg.11 – 15)

EN 9INFORMATION● If "AUTO CLOCK" is set to "ON" at the Clock Set screen on page 12, the clock will be adjusted automatically by the host

channel every hour on the hour (except for 11:00 PM, midnight, 1:00 AM and 2:00 AM) by the incoming PBS channel clocksetting data. (This automatic clock adjustment can only be performed when the VCR’s power is turned off. The clock will beadjusted on the hour based on the time displayed on the VCR, not on the actual real time.) The default setting of "AUTOCLOCK" is "ON".

● If the memory backup fails, because of a power outage or because the AC was removed from the VCR, Plug & Play will beperformed when power is restored to the VCR.

What To Do If Plug & Play Has Failed● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from

an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semi-Auto (Z pg. 12) orManual Clock Set (Z pg. 13) procedure. Auto channel set has already taken place and it need not be set again.

● If “- -:- -” appears on the display, your antenna cable may not be connected to the VCR or there may not be a Host PBS signalavailable in your area. Ensure that the antenna cable is connected correctly. Then power on and power off the VCR; the Plug &Play function will be automatically reactivated and "Auto" will be displayed on the VCR's front panel. If Plug & Play is notperformed but the antenna cable is connected correctly, perform the Manual Clock Set procedure (Z pg. 13). Auto channelset has not yet taken place, so please also perform the “Set Receivable Channels” procedure (Z pg. 14).

10 EN INITIAL SETTINGS (cont.)

LanguageThis VCR offers you the choice to view on-screen messages inEnglish, Spanish or French (not including messages superimposedon the TV picture). Select the desired language using thisprocedure. The default setting is "ENGLISH".

TURN ON THE VCR

1 Press POWER.

ACCESS MAIN MENUSCREEN

2 Press MENU.

ACCESS INITIAL SETSCREEN

3 At the Main Menu screen,move the highlight bar(arrow) to “INITIAL SET”by pressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS .

SELECT LANGUAGE

4 Move the highlight bar(arrow) to "LANGUAGE"by pressing CH 5∞ orSHUTTLE PLUS %fi, thenpress OK or SHUTTLEPLUS to select thedesired language.

RETURN TO NORMALSCREEN

5 Press MENU.

Turn on the TV and select the VCR channel 3 or 4 (or AVmode).

%

1 2 3

4 5 6

7 8 9

0

2

4

1

3

POWER

MENUOK

MAIN MENU

FUNCTION SETTUNER SET

= INITIAL SET

PRESS (5,∞), THEN (OK)PRESS (MENU) TO END

%

SHUTTLE PLUS

INITIAL SET

CLOCK SET=LANGUAGE ENGLISH

GUIDE CHANNEL SET

SELECT WITH (5,∞) AND (OK)PRESS (MENU) TO END

POW

ER

MEN

U

OKCH

EN 11

ClockPerform clock setting only if the clock has not been set correctlyby the Plug & Play function or you use a cable box. Access theClock Set screen to perform the Semi-Auto or Manual clocksetting procedure. Each procedure starts from step 5.If you use a cable box, set the clock manually. (Z pg. 13)


1 2 3

4 5 6

7 8 9

0

2

4

1

3

POWER

MENUOK

SHUTTLE PLUS

Preparation

TURN ON THE VCR

1 Press POWER.


2 Press MENU.


3 At the Main Menu screen,move the highlight bar(arrow) to “INITIAL SET”by pressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS .

ACCESS CLOCK SETSCREEN

4 Move the highlight bar(arrow) at the Initial Setscreen to “CLOCK SET” bypressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS .

%%

MAIN MENU


= INITIAL SET


INITIAL SET

=CLOCK SETLANGUAGE ENGLISHGUIDE CHANNEL SET


CH

OK

MEN

U

POW

ER

12 EN INITIAL SETTINGS (cont.)

Semi-AutoYou can change the Host Channel/D.S.T. /Time Zone settingmanually.

SET AUTO CLOCK TO ON

5 At the Clock Set screen,press OK or SHUTTLEPLUS to move thehighlight bar to "AUTOCLOCK" and press CH 5∞or SHUTTLE PLUS %fi toset to "ON".a– To select the Host

Channel — go to step 6b– To select the D.S.T. mode — go to step 7c– To select the Time Zone — go to step 8

NOTE:The time that has been set previously will be erasedwhen "AUTO CLOCK", "HOST CH", "D.S.T." or "TIMEZONE" setting is changed.

SELECT HOST CHANNEL

6 You can either select "AUTO" or enter a PBS channelnumber. Move the highlight bar to "HOST CH" bypressing OK or SHUTTLE PLUS , then press CH 5∞or SHUTTLE PLUS %fi to set to "AUTO" or the desiredPBS channel number.

NOTE:There are some PBS channels that do not transmit clocksetting data.

SELECT D.S.T. MODE

7 You have three choices:a– Select "AUTO" and the adjustment to your VCR's

clock will be made according to the incoming signalfrom the host channel.

b– Select "ON" and the adjustment will be made basedon the clock itself.

c– Select "OFF" if Daylight Saving Time does not applyto you.

Move the highlight bar to "D.S.T." by pressing OK orSHUTTLE PLUS , then press CH 5∞ or SHUTTLEPLUS %fi to select the desired mode.

%

1 2 3

4 5 6

7 8 9

0

2

4

1

3

POWER

MENUOK

SHUTTLE PLUS

**AUTO DAYLIGHT SAVING TIMEThis function enables automatic adjustment of the VCR’sclock at the start and end of Daylight Saving Time.With Auto DST activated, . . .. . . on the first Sunday of April at 2:00 AM, the clock is

adjusted to 3:00 AM.. . . on the last Sunday of October at 2:00 AM, the clock is

adjusted to 1:00 AM.

%

%

CLOCK SET

TIME DATE YEAR1:00PM 12/24 98 THU

AUTO CLOCK : ONHOST CH : AUTO (CATV)D.S.T. : AUTOTIME ZONE : AUTOPRESS (5,∞), THEN (OK)PRESS (MENU) TO END

MEN

U

CH

OK

EN 13

SET TIME

5 Press CH 5∞ or SHUTTLEPLUS %fi until the desiredtime appears, then pressOK or SHUTTLE PLUS .

● Press and hold CH 5∞or SHUTTLE PLUS %fito change the time by 30minutes.

● When the time is entered manually, "AUTO CLOCK"will be automatically set to "OFF", and "HOST CH"and "TIME ZONE" will disappear.

SET DATE

6 Press CH 5∞ or SHUTTLE PLUS %fi until the desireddate appears, then press OK or SHUTTLE PLUS .

● Press and hold CH 5∞ or SHUTTLE PLUS %fi tochange the date by 15 days.

SET YEAR

7 Press CH 5∞ or SHUTTLE PLUS %fi until the desiredyear appears, then press OK or SHUTTLE PLUS twice.

SELECT D.S.T. MODE

8 Press CH 5∞ or SHUTTLE PLUS %fi to select thedesired mode.a– Set to "ON" so that the adjustment to your VCR's

clock will be made on the clock itself.b– Set to "OFF" if Daylight Saving Time does not apply

to you.

START CLOCK

9 Press MENU and normal screen appears.

Manual

%

%

To Make CorrectionsPress OK or SHUTTLE PLUS until the item you want tochange blinks, then press CH 5∞ or SHUTTLE PLUS %fi.

%

SELECT TIME ZONE

8 You can select the time zone automatically or manu-ally. Move the highlight bar to "TIME ZONE" bypressing OK or SHUTTLE PLUS , then press CH 5∞or SHUTTLE PLUS %fi to select "AUTO" or the desiredtime zone.

AUTO ATLANTICHAWAII EASTERNALASKA CENTRALPACIFIC MOUNTAIN

NOTE:If an incorrect time is displayed by the Plug & Playfunction, you may be receiving the clock setting data ofa PBS channel from an adjacent time zone or from anincorrect PBS channel from a cable TV system. If youselected "AUTO" for the host channel in step 6, be sureto select the correct time zone manually.


9 Press MENU.

IMPORTANTTurn the VCR off after performing the Semi-Auto Clock Setprocedure. "Auto" will appear on the front display panel whenthe clock is being set. The current time will appearautomatically when the clock is set.

%%

CLOCK SET

TIME DATE YEAR– –:– –AM 1/ 1 98AUTO CLOCK : ONHOST CH : AUTO (CATV)D.S.T. : AUTOTIME ZONE : AUTOPRESS (5,∞), THEN (OK)PRESS (MENU) TO END

14 EN

TunerSet Receivable Channels

TURN ON THE VCR

1 Press POWER.


2 Press MENU.

ACCESS TUNER SETSCREEN

3 Move the highlight bar(arrow) to "TUNER SET" bypressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS .

PERFORM AUTO CHANNELSET

4 Move the highlight bar(arrow) to "AUTOCHANNEL SET" bypressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS .

● Receivable channels inyour area areautomatically assigned tothe CH5∞ (+/–) buttons,and non-receivablechannels are skipped.

NOTES:● At the end of Auto

Channel Set, “SCANCOMPLETED” appears on screen.

● If the scan was unsuccessful, “SCAN COMPLETED–NO SIGNAL” appears on screen. Check theconnections and start again.


5 Press MENU.

INITIAL SETTINGS (cont.)

%%

INFORMATIONThe VCR detects the band (TV or CATV) and selects thecorrect band automatically during Auto Channel Set.The selected band will be displayed on the right side of"BAND" on the Tuner Set screen.

1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENUOK

SHUTTLE PLUS


POWER

CH+/–

MAIN MENU

FUNCTION SET= TUNER SET

INITIAL SET


AUTO CHANNEL SET

SCANNING...

PRESS (MENU) TO END

TUNER SET

BAND CATV=AUTO CHANNEL SET

MANUAL CHANNEL SET


OKCH

MEN

U

POW

ER

EN 15Add Or Delete A Channel


1 Press MENU.

ACCESS TUNER SETSCREEN

2 Move the highlight bar (arrow) to "TUNER SET" bypressing CH5∞ or SHUTTLE PLUS%fi, then press OKor SHUTTLE PLUS .

ACCESS MANUALCHANNEL SET SCREEN

3 Move the highlight bar(arrow) to "MANUALCHANNEL SET" bypressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS .

ADD OR SKIP DESIREDCHANNEL

4 Input the channel numberusing the NUMBER keys orby pressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS to set to "ADD" or"SKIP" as required. Repeatfor each channel you wantto add or skip.


5 Press MENU.

1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENUOK

SHUTTLE PLUS

NUMBER

%

%%

TUNER SET

BAND CATVAUTO CHANNEL SET

=MANUAL CHANNEL SET


MANUAL CHANNEL SET

(CATV)CH 45 ADD

PRESS NUMBER KEY (0–9)OR (5,∞), THEN (OK)

PRESS (MENU) TO END

CH

OK

MEN

U

16 EN SIMPLE PLAYBACK AND RECORDING

SimplePlayback

LOAD A CASSETTE

1 Make sure the window side is up, the rear label side isfacing you and the arrow on the front of the cassette ispointing towards the VCR. Don’t apply too muchpressure when inserting.

● The VCR’s power comes on automatically.● The counter is automatically reset to "0:00:00".● If the cassette's record safety tab has been removed,

playback begins automatically.

FIND PROGRAM STARTPOINT

2 If the tape is advanced past the start point, press REW.To go forward, press FF.

START PLAYBACK

3 Press PLAY. "AUTO PICTURE" appears on the screen(when AUTO PICTURE is set to "ON" Z pg. 26).

STOP PLAYBACK

4 Press STOP or STOP/EJECT. Then press STOP/EJECTto remove the cassette.


1 2 3

4 5 6

7 8 9

0

2

4

1

3

PLA

Y

REW (Rewind)FF (Fast-Forward)

STO

P

STO

P/EJ

ECT

INFORMATIONThis video recorder is equipped with SQPB (S-VHS QUASIPLAYBACK) that lets you watch tapes recorded in the S-VHSformat with regular VHS resolution.● SQPB does not deliver Super VHS resolution.● S-VHS recording is not possible with this video recorder.

Usable cassettes

Full-Size VHST-30 (ST-30**)T-60 (ST-60**)T-90T-120 (ST-120**)T-160 (ST-160**)ST-210**

Compact VHS*TC-20 (ST-C20**)TC-30 (ST-C30**)TC-40 (ST-C40**)

* Compact VHS camcorder recordings can be played onthis video recorder. Simply place the recorded cassetteinto a VHS Cassette Adapter and it can be used just likeany full-sized VHS cassette.

** This video recorder can record on regular VHS andSuper VHS cassettes. However, it will record regularVHS signals only.

FF

PLAY

REW

EN 17

SimpleRecording

LOAD A CASSETTE

1 Make sure the record safety tab is intact. If not, cover thehole with adhesive tape before inserting the cassette.

SELECT RECORDINGCHANNEL

2 Press CH5∞ (+/–). Or press the appropriate NUMBERkeys, then press ENTER. (The channel changes after afew seconds whether you press ENTER or not.)

● If you use the RF connection, by pressing the TV/VCRbutton, select VCR mode to view the program to berecorded.

SET TAPE SPEED

3 Press SP/EP to set the recording speed.

START RECORDING

4 Press and hold REC and press PLAY on the remotecontrol, or press REC on the VCR's front panel.

PAUSE/RESUMERECORDING

5 Press PAUSE. Press PLAY to resume recording.

● During record pause, you can change the recordingchannel by using the CH5∞ (+/–) buttons orNUMBER keys.

STOP RECORDING

6 Press STOP or STOP/EJECT. Then press STOP/EJECT toremove the cassette.


1 2 3

4 5 6

7 8 9

0

2

4

1

3

PAUSE

STO

P

REC

PLAY

SP/EP

CH

TV/VCR ENTE

R

NUMBER

● To prevent accidental recording on a recorded cassette,remove its record safety tab.To record on it later, cover the hole with adhesive tape.

Accidental erasure prevention

Record safety tab

PAU

SE

STO

P/EJ

ECT

REC

PLA

Y

CH

18 EN PLAYBACK AND RECORDING FEATURES

PlaybackFeatures

Reverse search

Reverse

Forward search

Forward

Reverse play

Reverse slow motion Slow motion Play

3 steps 5 steps 5 steps 4 steps

TV CH +

TV

VO

L–

TV CH –

TVVO

L+

SHUTTLEPLUS

1 2 3

4 5 6

7 8 9

0

2

4

1

3

SHUTTLE PLUS

CH

PLAY

PAUSE

Still Picture/Frame-By-Frame Playback

PAUSE DURING PLAYBACK

1 Press PAUSE. If there is vertical jitter, use the CH 5 (+) or∞ (–) button to correct the picture.

ACTIVATE FRAME-BY-FRAME PLAYBACK

2 Press PAUSE repeatedly to advance one frame at a time.

ORPress SHUTTLE PLUS £ repeatedly for forward frame-by-frame playback or SHUTTLE PLUS ™ repeatedlyfor reverse frame-by-frame playback.

To resume normal playback, press PLAY.

NOTE: Refer to the following for the operations describedon this page.

Slow Motion/Reverse SlowMotion

ACTIVATE SLOW-MOTIONPLAYBACK

1 For hands-free slow-motion, press and releaseSHUTTLE PLUS ™ during playback to decreasespeed in the forward direction. Continue to press andrelease SHUTTLE PLUS ™ to select the reverse slowmotion, reverse play and reverse search modes.

ORDuring still picture, press and hold SHUTTLE PLUS £for forward slow motion, or press and hold SHUTTLEPLUS ™ for reverse slow motion. Release to return tostill picture.

ORFor forward slow motion during still picture, press andhold PAUSE for more than 2 seconds. Press PAUSEagain to return to still picture.


CHPA

USE

PLA

Y

ACTIVATE VARIABLE-SPEEDSEARCH

1 During playback, repeatedly press and release SHUTTLEPLUS ™ or £ to select the search speed.

● To increase the speed in the forward direction, pressand release £ repeatedly to select the variousforward search modes.

● To decrease the speed in the forward direction, pressand release ™.

● To play in reverse slow motion, and in reverse playmode, continue to press ™ repeatedly afterselecting all the forward slow motion modes.


Variable-Speed Search/Reverse Motion Playback

EN 19High-Speed Search

ACTIVATE HIGH-SPEEDSEARCH

1 During playback or still, press FF for forward high-speed search, or REW for reverse high-speed search.


NOTE:For short searches, during playback or still, press and hold FF orREW for over 2 seconds. When released, normal playbackresumes.

Index SearchIndex codes are placed on the tape at the start of eachrecording. You can find and automatically play back from thestart of any recording using the Index Search function.

START SEARCH

1 While the tape is stopped, press SHUTTLE PLUS ™or £ ( or ).

ACCESS DISTANT CODE

2 To access a recording 2–9 index codes away, pressSHUTTLE PLUS ™ or £ ( or ) repeatedly untilthe correct number is displayed on screen (only ifSUPERIMPOSE is set to ON (Z pg. 23). Playback beginsautomatically when the desired recording is located.

● If necessary press REW or FF when play starts tosearch visually to find the very beginning of thedesired program.

NOTE:An index code is not placed on the tape when recording ispaused and then resumed.

fi %

SKIP OVER UNWANTEDSECTIONS

1 Press SKIP SEARCH 1 to 4 times during playback. Eachpress initiates a 30-second period of fast-motionplayback. Normal playback resumes automatically.

NOTES:● To return to normal playback during a Skip Search,

press PLAY.● If the Skip Menu screen appears, see page 25.

Skip Search

1 2 3

4 5 6

7 8 9

0

2

4

1

3

SHUTTLE PLUS

FF

PLAY

REW

FF

SKIP SEARCH

REW

PLAY

fi %

20 EN

Instant ReViewAt the press of a button, you can power up your VCR, rewind thetape and begin viewing the most recent timer-recorded program.

ACTIVATE INSTANT REVIEW

1 After ensuring that the Timer mode is disengaged, pressREVIEW.

● The power comes on and the VCR rewinds to the indexcode indicating the start of the last timer-recordedprogram, then begins playback automatically.

● You can access a program 2–9 index codes awayfrom the current position on the tape. If, for example,you have 5 programs recorded and you want towatch the third one, press REVIEW three times.

● If necessary press REW or FF when play starts tosearch visually to find the very beginning of thedesired program.

● If the tape is already rewound when REVIEW ispressed, it will play the tape from the beginning. Itwill not fast forward to an index code.

● The Instant Review function will also operate if theVCR's power is on.

Manual TrackingOnce playback begins, the VCR’s automatic tracking function isengaged. If tracking noise appears in the picture, you canoverride this and make the adjustment manually.

ENGAGE MANUALTRACKING MODE

1 During playback, press the CH5 and ∞ buttons on theVCR's front panel simultaneously to cancel theautomatic tracking mode and enable manual trackingadjust.

ADJUST MANUALTRACKING

2 Press CH 5 (+) or ∞ (–) on the VCR's front panel orremote. Press briefly for fine adjust, or press and hold forcoarse adjust. Watch the screen and continue adjustinguntil optimum picture and sound quality are achieved.

RE-ENGAGE AUTOMATICTRACKING

3 Press the CH5 and ∞ buttons on the VCR's front panelsimultaneously.

● When automatic tracking is re-engaged, Auto Pictureis automatically activated.

NOTES:● To obtain a noiseless still picture it may be necessary to adjust

tracking in slow playback and then engage Pause.● Manual tracking is possible during hands-free slow-motion.

During hands-free slow-motion playback, simply press CH 5(+) or ∞ (–) on the VCR's front panel or remote to adjusttracking.

PLAYBACK AND RECORDING FEATURES (cont.)

1 2 3

4 5 6

7 8 9

0

2

4

1

3

FF

FF REW

REW

CH

REVIEW

CH

EN 21Video StabilizerBy activating the Video Stabilizer you can correct verticalvibrations in the picture when playing back unstable EPrecordings that were made on another VCR. When this functionis set to "ON", vertical vibration will be automatically corrected.*The default setting is "OFF".


1 Press MENU.

ACCESS FUNCTION SETSCREEN

2 Move the highlight bar(arrow) to "FUNCTIONSET" by pressing CH5∞ orSHUTTLE PLUS%fi, thenpress OK or SHUTTLEPLUS .

ACTIVATE VIDEO STABILIZER

3

Move the highlight bar (arrow) to "VIDEO STABILIZER"by pressing CH 5∞ or SHUTTLE PLUS %fi, then pressOK or SHUTTLE PLUS to set to "ON".


4 Press MENU.

%

1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENUOK

SHUTTLE PLUS

MAIN MENU

= FUNCTION SETTUNER SETINITIAL SET


HR-VP450U HR-VP650UFUNCTION

AUTO TIMER OFFSUPERIMPOSE ONAUTO SP=EP TIMER OFF

=VIDEO STABILIZER ONNEXT PAGE


FUNCTION

AUTO TIMER OFFSUPERIMPOSE ONAUTO SP=EP TIMER OFF

=VIDEO STABILIZER ONAUTO PICTURE ON


%

OKCH

MEN

U

NOTES:● The Superimpose mode indications may jitter vertically when

"VIDEO STABILIZER" is set to "ON".● Regardless of the setting, this function has no effect with SP

recordings, during recording and during special-effectsplayback.

● When you finish viewing the tape, be sure to set it back to"OFF".

22 EN PLAYBACK AND RECORDING FEATURES (cont.)

Repeat Playback

1 2 3

4 5 6

7 8 9

0

2

4

1

3

C.RESET

POWER

DISPLAY

TIMER

FF

PAUSEREW

PLAY

STOP

START REPEAT

1 Press and hold PLAY (until " " blinks on the frontdisplay panel) during playback, then release.

● The entire tape is played back 50 times.

STOP REPEAT

2 To stop, press STOP at any time.

NOTE:Pressing PLAY, REW, FF, PAUSE or SHUTTLE PLUS™ or £ also stops Repeat Playback.

SHUTTLE PLUS

Tape Position IndicatorThe Tape position indicatorappears on screen when, from thestop mode, you press FF or REW,or perform an Index Search orInstant ReView. The position of" " in relation to "B" (Beginning)or "E" (End) shows you where youare on the tape.

NOTES:● "SUPERIMPOSE" must be set to "ON", or the indicator will not

appear (Z pg. 23).● It may take a few seconds for the Tape Position Indicator to be

displayed.

COUNT 0:33:27

B E+ + +

Next-Function MemoryThe Next Function Memory “tells” the VCR what to do afterrewinding. Before continuing, ensure that the VCR is in stopmode.a– For Automatic Start Of Playback After Tape Rewind . . .. . . press REW, then press PLAY within 2 seconds.b– For Automatic Power Off After Tape Rewind . . .. . . press REW, then press POWER within 2 seconds.c– For Automatic Timer Standby After Tape Rewind . . .. . . press REW, then press TIMER within 2 seconds.

NOTE:It is not possible to select the Automatic Timer functions if thecassette's record safety tab is removed.

SPVCR

RESET COUNTER TO ZERO

1 Press C.RESET.

NOTE:By pressing the DISPLAY button, you can change thedisplay to show the counter reading, channel numberor clock time. (Channel number is not displayed duringplayback.)

Counter Reset

POW

ER

PAU

SESTOP

FF

PLAY

REW

EN 23SuperimposeThis function, switchable between ON and OFF, determineswhether or not operational indicators will appear on screen.

1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENUOK

SHUTTLE PLUS

OSD

To recall an indication

1 Press OSD.n All indications corresponding to the current status are

displayed for 5 seconds. After that, the counterinformation and RECORD/PAUSE if in the RecordPause mode, are left displayed on the screen.

2 Press OSD again to clear the display.

CH 125 RECORDTHU 12:00 AM PAUSESTEREO ] SPSAP

INDEX-1NORMHI–FI COUNT –1:23:45

B E+ + +

Tuned-in channel or AUX(iliary) modeWhen the channel is changed, the new

channel is displayed on the screen for 5seconds.

Operation modeWhen the operation mode is changed,the new mode is displayed — RECORD(5 sec.), PLAY (5 sec.), FF/REW (5 sec.when engaged from Stop mode),RECORD PAUSE (for as long as Pause isengaged), and ITR *:** (5 sec.).

INDEX indication

Tape speed indication

"Cassette Loaded" markWhen a cassette is loaded, the mark isdisplayed for 5 seconds. It blinks when theVCR's EJECT button is pushed.Audio mode indications (HR-VP650U only) Counter reading


1 Press MENU.


2 Move the highlight bar (arrow) to "FUNCTION SET" bypressing CH5∞ or SHUTTLE PLUS%fi, then press OKor SHUTTLE PLUS .

SELECT SUPERIMPOSE SETMODE

3

Move the highlight bar (arrow) to "SUPERIMPOSE" bypressing CH5∞ or SHUTTLE PLUS%fi, then press OKor SHUTTLE PLUS to select the desired mode:a– Select "ON" if you want the superimposed opera-

tional indications on the TV screen.b– Select "OFF" if you do not want the superimposed

operational indications on the screen.


4 Press MENU.

%%

FUNCTION

AUTO TIMER OFF=SUPERIMPOSE ON

AUTO SP=EP TIMER OFFVIDEO STABILIZER OFFNEXT PAGE



AUTO TIMER OFF=SUPERIMPOSE ON

AUTO SP=EP TIMER OFFVIDEO STABILIZER OFFAUTO PICTURE ON


NOTES:● If you engage the Record Pause mode, RECORD/PAUSE is

displayed regardless of the Superimpose mode setting.● If you select a channel on which no signal is received, the

channel number is displayed regardless of the Superimposemode setting.

Clock time

Stereo program indication(HR-VP650U only)

Second Audio Program indication(HR-VP650U only)

Tape position indicator

The superimposed indication on the TV screen tells you what the VCR is doing.

CH

OK

MEN

U


Select The Soundtrack(HR-VP650U Only)Your VCR can record two soundtracks simultaneously (Normaland Hi-Fi) and play back the selected one, or both together. Or,when viewing a pre-recorded tape that contains two separateHi-Fi audio programs, you can choose to listen to either one byselecting either "Hi-Fi L" or "Hi-Fi R" in step 3.

1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENUOK

SHUTTLE PLUS


1 Press MENU.



SELECT AUDIO MONITORSET MODE

3 Move the highlight bar(arrow) to "AUDIOMONITOR" by pressingCH 5∞ or SHUTTLE PLUS%fi, then press OK orSHUTTLE PLUS toselect the desired mode:a– Hi-Fib– Hi-Fi Lc– Hi-Fi Rd– Normale– Mix


4 Press MENU.

%%

NOTES:● If the tape being played back has no Hi-Fi soundtrack, the

Normal soundtrack will be heard no matter what choice youmake in step 3.

● If RF connection is used for TV, even if Hi-Fi audio monitor isselected the sound will be mono and will be reproduced inboth loudspeakers.

FUNCTION

=AUTO TIMER OFFSUPERIMPOSE ONAUTO SP=EP TIMER OFFVIDEO STABILIZER OFFNEXT PAGE


PREVIOUS PAGE2ND AUDIO RECORD OFF

=AUDIO MONITOR HI–FIAUTO PICTURE ON


OKCH

MEN

U

EN 25Movie Advance(HR-VP650U Only)This feature helps you locate certain parts of prerecorded movies(rented or purchased) and works in two ways.● You can go to the beginning of the movie, skipping over all

previews.● You can fast-motion the tape to the beginning of the next

preview, so you can skip over previews one by one.1 2 3

4 5 6

7 8 9

0

2

4

1

3 OK

SHUTTLE PLUS

SKIP SEARCHPLAY

LOAD A CASSETTE

1 Insert a cassette that has a prerecorded movie (rented orpurchased), with no safety tab, into the VCR. Playbackbegins automatically.

ACCESS SKIP MENUSCREEN

2 Press SKIP SEARCH.

SELECT MODE

3 Press CH5∞ or SHUTTLEPLUS%fi to move thehighlight bar (arrow) toyour choice.a– Select "MOVIE

ADVANCE" if you wantto advance directly tothe beginning of themovie.

b– Select "MOVIE ADVANCE (PREVIEW)" if you wantto advance to the next preview.

c– Select "SKIP SEARCH" if you do not want to performMovie Advance, then press OK to go back to thenormal screen. Pressing SKIP SEARCH activates theSkip Search function (Z pg. 19).

PERFORM MOVIEADVANCE

4 a– If you selected "MOVIE ADVANCE" in step 3 andpress OK, the following screen will appear with ablue background. The VCR will rewind thebeginning of the tape, then will fast-motion to thebeginning of the movie. "READY" will appear andblink when the beginning of the movie is detectedand the Stop mode will be engaged. Press PLAY toview the movie.

b– If you selected "MOVIE ADVANCE (PREVIEW)" instep 3 and press OK, the VCR will fast-motion to thebeginning of the next preview and normal playbackwill resume when it is detected.Each press of SKIP SEARCH fast-motions to thebeginning of the next preview, thereby skipping overone preview each time.

SKIP MENU

= MOVIE ADVANCEMOVIE ADVANCE (PREVIEW)SKIP SEARCH

PRESS (5,∞), THEN (OK)PRESS (SKIP) TO CANCEL

MOVIE ADVANCE

READY

PRESS (PLAY) TO STARTPRESS (STOP) TO CANCEL

MOVIE ADVANCE

SEARCHING FOR BEGINNINGOF MOVIE.

PRESS (STOP) TO CANCEL

ATTENTIONMovie Advance works only on prerecorded cassettes thathave been recorded in the SP mode, and have no safety tab.If the VCR detects the EP mode after you press OK in step 4,the following screen appears.

MOVIE ADVANCE

MOVIE ADVANCE CAN NOTBE SELECTED FOR EPRECORDINGS.

PRESS (SKIP) TO CANCEL

NOTES:● Normally there is a period of black and no audio at the

beginning and end of previews. The Movie Advance featuredetects those parts where the picture fades to black and theaudio fades to silence, and initiates fast-motion to skip overthe detected previews.

● Some previews may not be detected and Movie Advance maynot work properly.

● The setting you selected in step 3 remains in effect until thecassette is ejected.

Patents Pending


Auto PictureAuto Picture compensates for variations in tape characteristicsto ensure the best possible playback picture. It checks andcompensates for the condition of the tape at the beginning ofautomatic tracking when playback is selected. The defaultsetting is "ON".


1 2 3

4 5 6

7 8 9

0

2

4

1

3

POWER

MENUOK

SHUTTLE PLUS

Preparation

TURN ON THE VCR

1 Press POWER.


2 Press MENU.


3 Press CH5∞ or SHUTTLEPLUS %fi to move thehighlight bar (arrow) to“FUNCTION SET”, thenpress OK or SHUTTLEPLUS .

SELECT AUTO PICTURE

4

Press CH 5∞ or SHUTTLEPLUS %fi to move thehighlight bar (arrow) to"AUTO PICTURE", thenpress OK or SHUTTLEPLUS to set to "ON" or"OFF".

NOTE:When using rental tapes,or tapes recorded on other VCRs, select "ON" or "OFF"as desired to give the best picture.


5 Press MENU.

%

MAIN MENU

= FUNCTION SETTUNER SETINITIAL SET


FUNCTION



PREVIOUS PAGE2ND AUDIO RECORD OFFAUDIO MONITOR HI–FI

=AUTO PICTURE ON


%


AUTO TIMER OFFSUPERIMPOSE ONAUTO SP=EP TIMER OFFVIDEO STABILIZER OFF

= AUTO PICTURE ON


POW

ER

MEN

U

OKCH

EN 27PlaybackThe VCR assesses the quality of the tape once you start playback.

Perform steps 1 and 2 on page 16 ("Simple Playback") beforecontinuing.

START PLAYBACK

1 Press PLAY.

● The VCR adjusts theplayback picture qualitybased on the quality ofthe tape in use.

NOTES:● When using rental tapes,

or tapes recorded on other VCRs, set “AUTOPICTURE” in step 4 of the Preparation procedure toeither “ON” or “OFF” as desired to give the bestpicture (Z pg. 26).

● The Auto Picture screen only appears at the begin-ning of automatic tracking. Even though the screendoesn't appear after that, the Auto Picture function isoperative.

● To display the Auto Picture screen, “SUPERIMPOSE”must be set to "ON" or the Auto Picture screen willnot appear (Z pg. 23).

AUTO PICTURE

1 2 3

4 5 6

7 8 9

0

2

4

1

3

PLA

Y

PLA

Y


Record One Program WhileWatching AnotherRecording

Features ENGAGE TV MODE

1 During recording...● Press TV/VCR. The VCR's VCR indicator goes out. (If

you are using the RF connection (Z pg. 6) to viewthe output from your VCR, the TV broadcast beingrecorded disappears.)

● If you are using the AV connection (Z pg. 6) to viewthe output from your VCR, change the TV's inputmode from AV to TV.

SELECT CHANNEL FORVIEWING

2 Use the TV’s channel selector to set the channel youwant to watch.

RESET COUNTER TO ZERO

1 Before recording starts, press C.RESET. The counterresets to zero and displays the exact elapsed time as thetape runs.

DISPLAY ELAPSED TIME ONSCREEN

2 During recording, press OSD at any time to see theelapsed time.All indications corresponding to the current status of theVCR are displayed for 5 seconds. The counter displayremains on the screen indicating the elapsed time.Press OSD again to remove the display.

● Make sure "SUPERIMPOSE" is set to "ON" (Z pg. 23).● The indications are not recorded.

Display Elapsed RecordingTime

1 2 3

4 5 6

7 8 9

0

2

4

1

3

OSDTV/VCR

C.RESET

EN 29Stereo And SAP(Second Audio Program)(HR-VP650U Only)Your VCR’s built-in MTS decoder enables reception of Multi-channel TV Sound broadcasts.When the channel is changed...● The "STEREO" indication appears on the screen for about 5

seconds if the program is a stereo broadcast.● The "SAP" indication appears on the screen for about 5

seconds if the program is an SAP broadcast.● Both indications appear when a stereo program is

accompanied by SAP audio.

To Record Stereo Programs . . .. . . simply follow the basic recording procedure.

To Listen To Stereo Soundtrack During Recording . . .. . . set "AUDIO MONITOR" to "HI-FI" at the Function screen(Z pg. 24).

1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENUOK

SHUTTLE PLUS

To Record SAP Programs . . .ACCESS MAIN MENUSCREEN

1 Press MENU.



SELECT 2ND AUDIORECORD SET MODE

3 Move the highlight bar(arrow) to "2ND AUDIORECORD" by pressing CH5∞ or SHUTTLE PLUS%fi, then press OK orSHUTTLE PLUS to set to"ON".


4 Press MENU.

%

FUNCTION



PREVIOUS PAGE=2ND AUDIO RECORD ON

AUDIO MONITOR HI–FIAUTO PICTURE ON


%

NOTES:● If a SAP program is received and "2ND AUDIO RECORD" is

set to "ON", the SAP audio is recorded on both the Normaland Hi-Fi tracks. The main audio program is not recorded.

● If a non-SAP program is received, the main audio is recordedon both the Hi-Fi and Normal audio tracks.

OKCH

MEN

U

30 EN

VCR Plus+TimerProgramming

TIMER RECORDING

Timer recording allows you to program the VCR to automaticallyrecord a program that will be broadcast at some future time.The timer record function can be programmed using VCR Plus+or Express Timer Programming up to 8 shows as far as a year inadvance. (Z pg. 30 or 34)The VCR Plus+ timer programming system eliminates the needto input channel, date, start and stop time data when setting thetimer record function. Simply key in the PlusCode number forthe TV program you wish to record and the VCR's timer will beautomatically programmed. (The PlusCodes are the numbersnext to the programs in most TV listings.)

LOAD A CASSETTE

1 Make sure the record safety tab is present.

● The VCR’s power comes on automatically.

ACCESS VCR PLUS+ SCREEN

2 Press PROG. on theremote control.

● The clock must be set inorder to access the VCRPlus+ screen. If youhaven’t set the clock, theMain Menu screenappears after an errormessage is displayed.Refer to page 8 for the Plug & Play procedure or page11 for the clock setting procedure.

ENTER PLUSCODE NUMBER

3 Press the appropriateNUMBER keys to enter thePlusCode number printedin the TV listings for theTV program you wish torecord and press OK.If the Guide Channel Setscreen appears, go to step 4.If the VCR Plus+ Programscreen appears, go to step 5.

● To make corrections, press CANCEL and input thecorrect PlusCode number.

INPUT RECEIVING CHANNELNUMBER

4 The Guide ChannelNumber, which is assignedto the TV or cable stationfor the PlusCode numberthat you entered in step 3,will appear automaticallyon the Guide Channel Setscreen. Input the numberof the channel on whichthe broadcast for the PlusCode number is received onthe VCR or cable box using the NUMBER keys, CH 5∞or SHUTTLE PLUS %fi, then press OK.

● The Guide Channel Set screen appears only whenyou input the PlusCode number of a station for whichthe Guide Channel number has not been set already.

VCR PLUS+

PRESS NUMBER KEY (0–9)PRESS (+/–) TO SET

EXPRESS PROGRAMMINGPRESS (PROG.) TO END

VCR PLUS+123

PRESS NUMBER KEY (0–9)THEN (OK)

PRESS (PROG.) TO END

GUIDE CHANNEL SET

GUIDE CH: 12VCR CH : –––

PRESS NUMBER KEY (0–9)OR (5,∞), THEN (OK)

PRESS (PROG.) TO END


1 2 3

4 5 6

7 8 9

0

2

4

1

3

CANCEL

PROG.

OK

SHUTTLE PLUS

NUMBER

EN 31

1 2 3

4 5 6

7 8 9

0

2

4

1

3

PROG.

OK

TIMER

SP/EP

PROGRAM 1(VCR PLUS+ 12345678)

START STOP8:00PM = 10:00PMDATE CH

12/24/98 12 SPTHU

PRESS (8=DAILY, 9=WEEKLYSTOP+/– = STOP TIME, SP/EP)PRESS (OK) TO END

CHECK PROGRAM DATA

5 The PlusCode number youentered and the matchingTimer-Recording informa-tion is displayed on theProgram screen. Check tomake sure it’s accurate.

● To change the stop time,press STOP +/–.

● To timer-record daily or weekly serials, press DAILY(NUMBER “8”) or WEEKLY (NUMBER “9”). “DAILY”or “WEEKLY” appears on the Program screen.Pressing the button again makes each correspondingdisplay disappear.

● If you made a mistake, press CANCEL to access theVCR Plus+ screen again and input the correctPlusCode number.

● If the PlusCode number you inputted is incorrect,"ERROR" may appear on the screen to advise you ofthe error. This happens when the PlusCode number isfor a program which has already passed. "ERROR" isdisplayed for about 5 seconds and the VCR Plus+screen reappears.

SET TAPE SPEED

6 Press SP/EP.


7 Press PROG. or OK. "PROGRAM COMPLETED"appears on the screen for about 5 seconds, then normalscreen appears.

ENGAGE TIMER MODE

8 Press TIMER. The VCR turns off automatically and "‰"is displayed on the display panel.

IMPORTANTIf you have moved to a different area or if a broadcastingstation's channel number has been changed, the wrongVCR or CABLE CH number will be displayed on the VCRPlus+ Program screen in step 5. When this happens, set thecorrect the Guide Channel number for that station.(Z pg. 32, "VCR Plus+ Setup")

NOTES:● To disengage the timer before recording starts, press TIMER

again. Pressing once more re-engages it.● In case of a power failure after programming, the VCR’s

memory backup keeps your selections for approximately10 minutes.

● When timer-recording cable channels received through aCable Box, be sure to keep the Cable Box set to ON.

NUMBER "9"

CANCEL

STOP+/–

NUMBER "8"

10:00 11:00 12:00

ATTENTIONIf there is a conflict in the timer schedule and one programoverlaps with another, only the parts shown below in graywill be recorded.

Pattern 1: The program with the lower program numberwill be recorded.

Pattern 2: The program that is broadcast earlier will berecorded.

Pattern 3: The program that is broadcast earlier will berecorded, followed by the remaining portion ofthe other program.

CH10

CH40 Not recordedProgram 1Program 2

10:00 11:00 12:00CH10

Program 2 Not recordedProgram 1

CH40

10:00 11:00 12:00CH10

CH40Program 1

Program 2

Not recorded

32 EN

VCR Plus+Setup


1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENU

POWER

TIMER RECORDING (cont.)

MEN

U

POW

ER

IMPORTANTIf you have moved to a different area or if a broadcastingstation's channel number has been changed, the wrong VCRor CABLE CH number will be displayed on the VCR Plus+Program screen (Z step 5 on page 31). When this happens,perform the following steps to set the correct the GuideChannel number for that station.

OKCH

OK

SHUTTLE PLUS

To ensure that VCR Plus+Timer Recording operates correctly itis necessary to set the VCR Plus+ "Guide Channel Set " for eachstation. Please read the following information carefully.

VCR Plus+ Guide Channel MatchingVCR Plus+ assigns a VCR Plus+ "Guide Channel" to broadcastand cable TV channels. These Guide Channel numbers are alsocalled the VCR Plus+ Channel Codes. Most TV listings have asection, usually a chart, indicating the "Guide Channel"numbers assigned to each station. For accurate VCR Plus+Programming the VCR Plus+ Guide Channel number for eachstation should match the channel number on which it isreceived in your area.

NOTES:● In many instances the VCR Plus+ Guide Channel numbers for

cable and broadcast TV stations DO NOT match the channelnumber on which it is received by your VCR or cable box.Check your TV listing, or contact your cable supplier fordetails.

● Many broadcast TV stations can be viewed on cable. Checkyour TV listing, or contact your cable supplier for details.

%

MAIN MENU


= INITIAL SET


TURN ON THE VCR

1 Press POWER.


2 Press MENU.


3 Press CH5∞ or SHUTTLEPLUS%fi to move thehighlight bar (arrow) to“INITIAL SET”, then pressOK or SHUTTLE PLUS .

EN 33ACCESS GUIDE CHANNELSET SCREEN

4 Press CH5∞ or SHUTTLEPLUS%fi to move thehighlight bar (arrow) to“GUIDE CHANNEL SET”,then press OK or SHUTTLEPLUS .

INPUT GUIDE CHANNELNUMBER

5 Press CH5∞, SHUTTLEPLUS%fi or theappropriate NUMBERkeys to input the VCRPlus+ Guide Channelnumber as shown in theTV listing. Then press OKor SHUTTLE PLUS .

INPUT RECEIVING CHANNELNUMBER

6 Press CH5∞, SHUTTLEPLUS%fi or theappropriate NUMBER keysto input the number of thechannel on which theGuide Channel’s broad-casts are received. Thenpress OK or SHUTTLEPLUS .

● Repeat steps 5 and 6 foreach instance.


7 Press MENU.

1 2 3

4 5 6

7 8 9

0

2

4

1

3

MENUOK

NUMBER

SHUTTLE PLUS

OKCH

MEN

U

(Ex.) When inputting theGuide Channel number6 for WNJU(Ind.)

%

%

GUIDE CHANNEL SET

GUIDE CH : 6VCR CH : – – –

PRESS NUMBER KEY (0-9)OR (5,∞), THEN (OK)

PRESS (MENU) TO END

INITIAL SET

CLOCK SETLANGUAGE ENGLISH

=GUIDE CHANNEL SET


(Ex.) If WNJU(Ind.) isreceived on channel 47

GUIDE CHANNEL SET=

GUIDE CH : 6VCR CH : 47

PRESS NUMBER KEY (0-9)OR (5,∞), THEN (OK)

PRESS (MENU) TO END

%

ATTENTION CABLE BOX SUBSCRIBERS● In order to set the Guide Channel for a cable program,

you must select your cable box's output channel as theVCR channel in step 6. If the cable box is connected toyour VCR's ANT. IN connector, select the cable box's RFoutput channel. If the cable box is connected to yourVCR's VIDEO IN and AUDIO IN connectors, pressNUMBER key "0" to select "F-1" as the VCR channel.

● It is important that you keep the cable box ON andtuned to the cable station of the program you want torecord until timer recording is completed.

34 EN TIMER RECORDING (cont.)

You can directly program the VCR’s timer to record up to 8shows, as far as a year in advance. Remember, the clock must beset before you can program the timer (Z pg. 8 or 11).Express Timer

ProgrammingTurn on the TV and select the VCR channel 3 or 4 (or AVmode).

1 2 3

4 5 6

7 8 9

0

2

4

1

3

PROG.

START+/–

STO

P+/–

DA

TE+

/–

LOAD A CASSETTE

1 Make sure the record safety tab is intact. If not, coverthe hole with adhesive tape, then load it into the VCR.

● The VCR comes on, and the counter is reset,automatically.

ACCESS VCR PLUS+SCREEN

2 Press PROG.

ACCESS PROGRAMSCREEN

3 Press START +/–. (If you’rejust starting out, “PRO-GRAM 1” appears.)

SET PROGRAM START TIME

4 Press START +/– to enterthe time you wantrecording to start.

● Press and hold START+/– to move in 30-minute increments, orpress and releaserepeatedly to move 1minute at a time.

SET PROGRAM STOP TIME

5 Press STOP +/– to enter the time you want recording tostop.

● Press and hold STOP +/– to move in 30-minuteincrements, or press and release repeatedly to move 1minute at a time.

SET PROGRAM DATE

6 Press DATE +/–. (The current date is displayed onscreen. The date you enter appears in its place.)

PROGRAM 1

START STOP– –:– –AM = – –:– –AMDATE CH

– –/– –/– – – – – SP

PRESS (+/–, SP/EP, 8=DAILY,9=WEEKLY), THEN (0K)PRESS (PROG.) TO END

PROGRAM 1

START STOP8:00 AM = – –:– –AMDATE CH

– –/– –/– – – – – SP

PRESS (+/–, SP/EP, 8=DAILY,9=WEEKLY), THEN (0K)PRESS (PROG.) TO END

EN 35

1 2 3

4 5 6

7 8 9

0

2

4

1

3 OK

NUMBER "9"

NUMBER "8"

TIMER

SP/EP

CH

SET CHANNEL NUMBER

7 Press CH +/–.

● Holding down CH +/– rapidly scans through thechannels.

● If you are using a cable box (or DBS receiver), enterthe cable box (or DBS receiver) channel, not thechannel to be recorded. The channel to be recordedmust be selected on the cable box (or DBS receiver).(The cable box (or DBS receiver) channel is the VCR'schannel that displays the channels received by thecable box (or DBS receiver).)

SET TAPE SPEED

8 Press SP/EP to set the tape speed.


9 Press PROG. or OK. "PROGRAM COMPLETED"appears on the screen for about 5 seconds, then normalscreen appears.

ENGAGE TIMER MODE

10 Press TIMER. The VCR turns off automatically and "‰"is displayed on the display panel.

To Timer-Record Weekly Or Daily Serials . . .. . . anytime during steps 3 through 9, press WEEKLY (NUMBERkey “9”) for weekly serials or DAILY (NUMBER key “8”) fordaily serials (Monday–Friday). Either "WEEKLY" or "DAILY"appears on the screen. Pressing the button again makes thecorresponding indication disappear.

NOTES:● To disengage the timer before recording starts, press TIMER

again. Pressing once more re-engages it.● In case of a power failure after programming, the VCR’s memory

backup keeps your selections for approximately 10 minutes.● Programs that start after midnight must have the next day’s date.● After timer recording is completed, the VCR’s power goes off

automatically.● You can program the timer while a regular recording is in

progress; the on-screen menu will not be recorded.● If the end of tape is reached during timer recording, the

cassette is automatically ejected.● When timer-recording cable or satellite channels through an

external tuner, be sure to keep the cable box or satellitereceiver's power ON.

PROG.

10:00 11:00 12:00

ATTENTIONIf there is a conflict in the timer schedule and one programoverlaps with another, only the parts shown below in graywill be recorded.

Pattern 1: The program with the lower program numberwill be recorded.

Pattern 2: The program that is broadcast earlier will berecorded.

Pattern 3: The program that is broadcast earlier will berecorded, followed by the remaining portion ofthe other program.

CH10

CH40 Not recordedProgram 1Program 2

10:00 11:00 12:00CH10

Program 2 Not recordedProgram 1

CH40

10:00 11:00 12:00CH10

CH40Program 1

Program 2

Not recorded

36 EN TIMER RECORDING (cont.)

Check, Cancel And RevisePrograms

1 2 3

4 5 6

7 8 9

0

2

4

1

3

POWER

TIMER

PROG. C

HECK

CH+/–

CANCEL

START+/–

STO

P+/–

DA

TE+

/–

DISENGAGE TIMER

1 Press TIMER, then press POWER.

ACCESS PROGRAMCHECK SCREEN

2 Press PROG. CHECK.

ACCESS PROGRAMSCREEN

3 Press PROG. CHECK again to check more information.Each time you press PROG. CHECK, the next program'sinformation appears.

PR START STOP CH DATE1 8:00P 10:00 12 12/242 10:00A 10:45 40 12/253 11:30P 01:00 125 12/2545678

PRESS (CHECK) TO NEXT

To Cancel Or Revise A Program...

CANCEL OR REVISE APROGRAM

4 To cancel a program, press CANCEL.To revise a program, press the appropriate button:START+/–, STOP+/–, DATE+/–, CH+/–, SP/EP.


5 Press PROG. CHECK as many times as necessary. Ifthere are still programs remaining, go to step 6.

RE-ENGAGE TIMER

6 Press TIMER.

SP/EP

POW

ER

MEN

U

OK

CH

MENUOK

SHUTTLE PLUS

EN 37


1 Press MENU.



SELECT AUTO TIMER SETMODE

3

Move the highlight bar (arrow) to "AUTO TIMER" bypressing CH5∞ or SHUTTLE PLUS%fi, then press OKor SHUTTLE PLUS to set to "ON" or "OFF".


4 Press MENU.

Auto TimerWhen the Auto Timer is set to ON the timer is automaticallyengaged when the VCR's power is turned off. It is automaticallydisengaged when the VCR is powered back on.

Auto SP→EP TimerIf, when recording in SP mode, there is not enough tape to recordthe entire program, the VCR automatically switches to EP modeto allow complete recording. This feature is especially handywhen recording a program of more than 2 hours in length.

For Example . . .Recording a program of 140 minutes in length onto a 120-minute tape

Make sure you set "AUTO SP→EP TIMER" to “ON” at theFunction screen before the timer recording starts.

%

FUNCTION



Approximately 110 minutes

SP mode

Approximately 30 minutes

EP mode

Total 140 minutes


1 Press MENU.


2 Move the highlight bar (arrow) to "FUNCTION SET" bypressing CH 5∞ or SHUTTLE PLUS %fi, then press OKor SHUTTLE PLUS .

SELECT AUTO SP→EPTIMER SET MODE

3

Move the highlight bar (arrow) to "AUTO SP→EPTIMER" by pressing CH 5∞ or SHUTTLE PLUS %fi,then press OK or SHUTTLE PLUS to set to "ON".


4 Press MENU.

%FUNCTION

AUTO TIMER OFFSUPERIMPOSE ON

= AUTO SP=EP TIMER ONVIDEO STABILIZER OFFNEXT PAGE



AUTO TIMER OFFSUPERIMPOSE ON

=AUTO SP=EP TIMER ONVIDEO STABILIZER OFFAUTO PICTURE ON


%

%


=AUTO TIMER OFFSUPERIMPOSE ONAUTO SP=EP TIMER OFFVIDEO STABILIZER OFFAUTO PICTURE ON


NOTE:For safety, when AUTO TIMER is set to “OFF”, all other VCRfunctions are disabled while the Timer mode is engaged. Todisengage the timer, press TIMER.

NOTES:● If you have programmed the VCR to timer-record 2 or more

programs, the second program and those thereafter may notfit on the tape if you set the Auto SP→EP Timer mode to"ON". In this case, make sure the mode is not engaged, thenset the tape speed manually during timer programming.

● In order to ensure that the recording fits on the tape, this featuremay leave a slight non-recorded section at the end of the tape.

● There may be some noise at the point on the tape where theVCR switches from SP to EP mode.

● The Auto SP→EP Timer feature is not available during ITR(Instant Timer Recording), and the feature will work with thefollowing tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.

38 EN

Instant TimerRecording(ITR)

This easy method lets you record from 30 minutes to 6 hours(selectable in 30-min. increments) and shuts the VCR off afterrecording is finished.

START RECORDING

1 Press REC on the front panel.

ENGAGE ITR MODE

2 Press REC again. " " blinks and 0:30 appears on thefront display panel.

SET RECORDINGDURATION

3 If you want to record for more than 30 minutes, pressREC to extend the time. Each press extends recordingtime by 30 minutes.

NOTES:● You can only perform ITR using the REC button on the VCR's

front panel.● After you set the ITR time, the previous display reappears.● To check the remaining time, press REC once during record-

ing and the remaining time will be displayed for about 5seconds. Be careful not to press REC again within these 5seconds, or you will round the recording time up to the next30 minute increment.

TIMER RECORDING (cont.)

SPVCR

REC

EN 39

Edit ToAnother VCR

You can use your VCR as the player and another VCR as therecorder.

EDITING

MAKE CONNECTIONS

1 Connect an AV cable between your VCR's VIDEO OUTand AUDIO OUT connectors and another VCR’sVIDEO IN and AUDIO IN connectors.

For HR-VP650U owners...● When connecting to a monaural VCR, connect your

VCR's AUDIO OUT L connector to the AUDIO INconnector on the monaural VCR.

For HR-VP450U owners...● When connecting to a Hi-Fi VCR, connect your

VCR's AUDIO OUT connector to the AUDIO IN Lconnector on the Hi-Fi VCR.

LOAD CASSETTES

2 Insert the playback cassette into your VCR and thecassette to be recorded on into the other VCR.

SET RECORDER’S INPUTMODE

3 Set the other VCR's auxiliary (AV) input mode.

START PLAYER

4 Press PLAY on your VCR.

NOTE:If you don't want to record the superimposed indicationon the edited tape, be sure to set "SUPERIMPOSE" toOFF before pressing PLAY (Z pg. 23).

START RECORDER

5 Set the other VCR to its record mode.

VIDEO IN AUDIO IN

AUDIO OUT

Player Your VCR

VIDEO OUT

Audio/Video Cable(not supplied)

Recorder Another VCR

PLA

Y

40 EN EDITING (cont.)

Edit From ACamcorder OrAnother VCR

You can use a camcorder or another VCR as the player and yourVCR as the recorder.

MAKE CONNECTIONS

1 Connect an AV cable between the camcorder’s or theplayback VCR's VIDEO OUT and AUDIO OUTconnectors and your VCR’s VIDEO IN and AUDIO INconnectors.

For HR-VP650U owners...● When using a monaural camcorder or a monaural

VCR, connect its AUDIO OUT connector to theAUDIO IN L connector on your VCR.

For HR-VP450U owners...● When using a Hi-Fi camcorder or a Hi-Fi VCR,

connect its AUDIO OUT L connector to the AUDIOIN connector on your VCR.

LOAD A CASSETTE

2 Insert the cassette to be recorded on into your VCR andthe playback cassette into the camcorder or theplayback VCR.

SET RECORDER’S INPUTMODE

3 Press NUMBER key “0” to set your VCR to F-1.

START PLAYER

4 Set the camcorder or the playback VCR to its playmode.

NOTE:If the camcorder or another VCR is equipped with asuperimpose/OSD disable feature then set its superim-pose or display feature to OFF before pressing play.

START RECORDER

5 Set your VCR to its record mode.

Camcorder

AUDIO IN

1 2 3

4 5 6

7 8 9

0

2

4

1NUMBER

"0"

AV cable (not supplied)

VIDEO OUT

AUDIO OUTor

Player

Another VCR

Player

Recorder Your VCR

VIDEO IN

EN 41SPECIAL FEATURES

1 2 3

4 5 6

7 8 9

0

2

4

1

3

TV Multi-Brand RemoteControlThe VCR's remote control can control several functions on JVCremote control TVs and on the brands of remote control TVslisted below. *The default setting is JVC code 01.

TURN ON THE TV

1 Turn the power on using the TV's remote control.

SET TV BRAND CODE

2 Refer to the chart in the left column. While holding downTV on the VCR's remote control, press MBR SET and enteryour TV’s brand code using the NUMBER keys, then pressSTOP.Follow the example shown below.Check if the TV's power goes off as it should. If it does,try other operations (Z step 3).

● Once you have set the remote control to operate theTV, you don’t have to repeat this step until youreplace your remote control’s batteries.

● PANASONIC has two codes. If the TV does notfunction with one code, try entering the other.

OPERATE TV

3 First, while holding down TV, press the correspondingbutton: POWER, TV CH +/–, TV/VCR, TV VOL +/–,NUMBER keys.

● For some brands of TV, you must press ENTER afterhaving pressed the NUMBER keys.

POWERTV

NUMBER

TV/VCR

MBR SET

ENTE

R

TV VOL +/–

TV BRAND NAME BRAND CODE

JVC 01

MAGNAVOX 02

MITSUBISHI 03

PANASONIC 04, 11

RCA 05

SHARP 06

SONY 07

TOSHIBA 08

ZENITH 09

HITACHI 10

SAMSUNG 12

SANYO 13

SEARS 13

(Ex.) To set remote control to RCA 05:

Press in succession

TVMBRSET

A/B

5 STOP0

Holddown

Release

NOTE:Depending on the type of TV, there may be cases where someor all functions cannot be operated using the remote control.

STOP

TV CH+/–

42 EN SPECIAL FEATURES (cont.)

Cable Box Multi-BrandRemote ControlThe VCR's remote control can control functions on the brandsof cable boxes listed below. Some cable box brands have morethan one code. If your cable box does not function with aspecified code, try other codes.

TURN ON THE CABLE BOX

1 Turn the power on using the cable box’s remote control.

ENTER CABLE BOX BRAND

2 While holding down CABLE/DBS on the VCR's remotecontrol, press MBR SET and use the NUMBER keys toenter the cable box brand number from the chart in theleft column and then press STOP.Follow the example shown below.Check if the cable box's power goes off as it should. If itdoes, try other operations (Z step 3).

● Once you have set the remote control to operate thecable box, you don't have to repeat this step until youreplace the remote control's batteries.

OPERATE CABLE BOX

3 First, while holding down CABLE/DBS, press thecorresponding button: POWER, TV CH +/–, NUMBERkeys.

● For some brands of cable box, you must press ENTERafter having pressed the NUMBER keys.

● To change the cable box's channel, press TV CH +/–or the NUMBER keys. (The CH +/– button can beused to change the VCR's channel only.)

1 2 3

4 5 6

7 8 9

0

2

4

1

3

POWERCABLE/DBS

MBR SET

STOP

ENTE

R NUMBER

CABLE BOX BRAND NAME BRAND CODE

ARCHER 01, 05, 17CABLETENNA 01, 17CABLEVIEW 15, 16, 17, 21, 25CITIZEN 15, 16, 17, 21, 25CURTIS 02DIAMOND 01, 17EASTERN 19GC BRAND 15, 16, 17, 21, 25GEMINI 15GENERAL INSTRUMENTS 01, 04, 06, 11, 12, 15HAMLIN 10, 18, 19, 23JASCO 15JERROLD 01, 04, 06, 11, 12, 15NOVAVISION 02OAK 07PANASONIC 13, 14PULSER 15, 16, 17, 21, 25RCA 13, 14REGAL 10, 18, 19, 23REGENCY 19REMBRANDT 01, 16, 17SAMSUNG 05, 16, 24SCIENTIFIC ATLANTA 02SIGMA 07SL MARX 05, 16, 17, 24, 25SPRUCER 13, 14STARGATE 05, 15, 16, 17, 21, 24, 25TELEVIEW 05, 16, 24TOCOM 01, 04, 16UNIKA 01, 17UNIVERSAL 16, 17, 25VIDEOWAY 03, 09, 22ZENITH 03, 09, 22

NOTES:● Depending on the type of cable box, there may be cases

where some or all functions cannot be operated using theremote control.

● It's not possible to set the remote control for both your cablebox and a DBS receiver at the same time. You can only set theremote control to operate one of these units at a time.

(Ex.) To set remote control to RCA 14:

Holddown

Press in succession

CABLE/DBS

MBRSETA/B

4 STOP1 Release

TV CH+/–

EN 43DBS Receiver Multi-BrandRemote ControlThe VCR's remote control can control functions on the brandsof DBS (Direct Broadcast Satellite) receivers listed below.

1 2 3

4 5 6

7 8 9

0

2

4

1

3

TURN ON THE DBSRECEIVER

1 Turn the power on using the DBS receiver's remotecontrol.

ENTER DBS RECEIVERBRAND

2 While holding down CABLE/DBS on the VCR’s remotecontrol, press MBR SET and use the NUMBER keys toenter the DBS receiver brand number from the chart inthe left column and then press STOP.Follow the example shown below.Check if the DBS receiver's power goes off as it should.If it does, try other operations (Z step 3).

● Once you have set the remote control to operate theDBS receiver, you don't have to repeat this step untilyou replace the remote control's batteries.

OPERATE DBS RECEIVER

3 First, while holding down CABLE/DBS, press thecorresponding button: POWER, TV CH +/–, NUMBERkeys.

● Depending on the DBS receiver you may have topress ENTER after having pressed the NUMBER keys.

● To change the DBS receiver's channel, press TV CH+/– or the NUMBER keys. (The CH +/– button can beused to change the VCR's channel only.)

POWERCABLE/DBS

MBR SET

ENTE

R

STOP

NUMBER

DBS BRAND NAME BRAND CODE

JVC (DISH Network) 51

ECHOSTAR (DISH Network) 51

PRIMESTAR 50SONY (DSS) 41

RCA (DSS) 40

NOTES:● Depending on the type of DBS receiver, there may be cases

where some or all functions cannot be operated using theremote control.

● It's not possible to operate a DBS receiver that is notequipped with a remote control sensor.

● Though ECHOSTAR has a number of different remote codes,this remote control is applicable only to one of those codespreset at the factory.

● It's not possible to set the remote control for both your DBSreceiver and a cable box at the same time. You can only setthe remote control to operate one of these units at a time.

(Ex.) To set remote control to JVC 51:

5

CABLE/DBS

MBRSETA/B

1 STOP Release

Holddown

Press in succession

TV CH+/–

44 EN

1 2 3

4 5 6

7 8 9

0

2

4

1

3

UNPLUG VCR'S POWERCORD

1 Unplug from the AC outlet.

SET REMOTE CONTROLCODE

2 While holding down A/B on the remote control, pressthe NUMBER key "2" and then press STOP.

PLUG IN POWER CORD

3 Plug back in to the AC outlet.

TURN VCR POWER ON

4 Press POWER on the remote.

The VCR will now respond only to B-code commands.To set the VCR back to respond to A code signals, repeat thesame procedure as shown above except pressing NUMBER key"1" instead of "2" in step 2.You can control two VCRs with the same remote control byswitching the remote's code between A and B (Z Step 2).

Control Two JVC VCRsThe remote control is capable of controlling two JVC VCRsindependently; one set to respond to your remote control's Acode control signals and another set to respond to B codecontrol signals. The remote control is preset to send A codesignals because your VCR is initially set to respond to A codesignals. You can easily modify your VCR to respond to B codesignals.

A/B

POWER

NUMBER "1"

STOP

NUMBER "2"

SPECIAL FEATURES (cont.)

EN 45TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easilycorrected, and this can save you the trouble of sending your VCR off for repair.

POSSIBLE CAUSE● The power cord is disconnected.

● The TIMER mode is engaged withAuto Timer set to "OFF" (Z pg. 37).

● The batteries are discharged.

SYMPTOM1. The power won’t come on.

2. The clock works, but the VCR’spower won’t come on.

3. The remote control won’t function.

CORRECTIVE ACTIONConnect the power cord.

Press TIMER to disengage.

Replace the dead batteries with newones.

SYMPTOM1. The cassette gets stuck partway

during loading, and is ejected.

CORRECTIVE ACTIONMake sure the cassette's window isfacing up, the rear label side is facingyou and the arrow on the front of thecassette is pointing towards the VCR.Then insert the cassette.

POSSIBLE CAUSE● The cassette was inserted incorrectly.

SYMPTOM1. The tape is running but the picture

won’t appear.

2. Noise appears during visual search.

3. (HR-VP650U only) Breaks arenoticeable in Hi-Fi soundtrack.

4. The playback picture is blurred orinterrupted, even though TVbroadcasts are clear.

5. (HR-VP650U only) The Hi-Fisoundtrack cannot be heard.

POSSIBLE CAUSE● If you’re using the RF OUT connec-

tion (Z pg. 6), the channel selectoron the TV is set incorrectly.

● If you’re using the AV connection(Z pg. 6), the TV receiver is set tothe wrong mode.

● This is normal.

● Automatic tracking is engaged.

● The video heads may be dirty.

● The AUDIO MONITOR option wasset incorrectly.

CORRECTIVE ACTIONSet the channel selector to channel 3or 4.

Set the TV receiver to its AV mode.

Disengage Auto Tracking and adjustthe tracking manually (Z pg. 20).

The heads must be cleaned. Consultyour JVC dealer.

Set AUDIO MONITOR to "HI-FI"(Z pg. 24).

CORRECTIVE ACTIONInsert a cassette.Remove the cassette and cover thehole with adhesive tape, or load acassette on which the record safetytab is intact.

Set the VCR to the appropriatechannel.

Refer to the directions and theillustration under “Edit To AnotherVCR” (Z pg. 39) or “Edit From ACamcorder Or Another VCR” (Z pg.40) and properly connect the units.Make sure the power to all units is on.

Select the recorder’s appropriateinput mode.

POSSIBLE CAUSE● There’s no cassette loaded.● The loaded cassette has had its

record safety tab removed.

● The VCR has been set to its AUXmode by mistake.

●The VCRs or the camcorder and theVCR have been incorrectly con-nected.

● The power to one or more of theunits has not been turned on.

● The recorder’s input mode has beenset incorrectly.

SYMPTOM1. Recording won’t start.

2. TV broadcasts won’t recordproperly.

3. Tape-to-tape editing won’t work.

RECORDING

PLAYBACK

POWER

TAPE TRANSPORT

CONTINUED ON NEXT PAGE

46 EN TROUBLESHOOTING (cont.)

CORRECTIVE ACTIONSet the clock and/or timer correctly.

Press TIMER and check to make surethat ‰ appears on the front displaypanel.Re-perform the set-up procedures.

Timer programming can’t be performedwhen timer recording is in progress.Wait until it finishes.

Load a cassette with the record safetytab intact, or with the hole coveredwith adhesive tape.

Remove the cassette and cover itshole with adhesive tape, or replace itwith a cassette on which the safetytab is intact.

Check the programmed data and re-program as necessary, then pressTIMER again.

The program may not have beenrecorded in its entirety. Next timemake sure you have enough time onthe tape to record the entire program.

Re-perform the VCR Plus+ setupprocedure (Z pg. 32).

Wait until a space in memory clears,or cancel unnecessary programinformation (Z pg. 36).

SYMPTOM1. Timer recording won’t work.

2. Timer programming won’t work.

3. ‰ and ] on the front displaypanel won’t stop blinking.

4. The cassette is automaticallyejected, and ‰ and ] on thefront display panel won’t stopblinking.

5. ‰ blinks for 10 seconds and thetimer mode is disengaged.

6. The cassette is automaticallyejected, the power shuts off and ‰and ] won’t stop blinking.

7. We moved, and now VCR Plus+doesn’t work properly.

8. “PROGRAM FULL” is displayed onthe screen.

POSSIBLE CAUSE● The clock and/or the timer have

been set incorrectly.● The timer is not engaged.

● The VCR has not been set up properly.

● Timer recording is in progress.

● The timer is engaged but there’s nocassette loaded.

● The loaded cassette has had itsrecord safety tab removed.

● TIMER has been pressed when thereare no programs in memory, or thetimer record program informationhas not been programmed correctly.

● The end of tape was reached duringtimer recording.

● The receivable stations in the new areaare received on different channels thanthose in the previous area.

● All 8 programs of the VCR’s timermemory are used.

TIMER RECORDING

OTHER PROBLEMSCORRECTIVE ACTION

If you need the skipped channels,restore them (Z pg. 15).

Press PAUSE to pause the recording,change channels, then press PLAY toresume recording.

Re-set the remote control to thecorrect brand (Z pg. 41 or 42 or 43).

Select a different Host Channel duringthe Semi-Auto setting procedure(Z pg. 12), or perform the Manualsetting procedure (Z pg. 13).

SYMPTOM1. When scanning channels, some of

them are skipped over.

2. The channel can’t be changed.

3. The remote control won’t operatemy TV or cable box or DBS receiver.

4. Even though Auto or Semi-Autoclock setting has been selected, theclock is incorrect.

POSSIBLE CAUSE● Those channels have been preset to

be skipped.

● Recording is in progress.

● The remote control brand setting isincorrect.

● The clock setting data received fromthe Host Channel is incorrect.

ATTENTION:This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the VCRdoes not operate correctly switch its power off and unplug the power cord from the AC supply. Wait for a while and then plug thepower back in. Eject and check the condition of the cassette. If everything appears normal resume operating the VCR as usual.

EN 47QUESTIONS AND ANSWERS

PLAYBACKQ. What happens if the end of the tape is reached

during playback or search?

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

A. The tape is automatically rewound to the beginning.

Q. Can the VCR indefinitely remain in the still mode?A. No. It stops automatically after 5 minutes to protect

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

the heads.

Q. During search, slow, still and frame-by-frameplayback, I can’t hear any audio. What’s theproblem?

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

A. This is normal.

Q. During search, still and frame-by-frame playback,the picture is intermittent. What’s the cause?

A. Picture loss occurs when these types of playback areattempted with a tape recorded in LP mode. PressingPLAY to return to normal playback will restore the

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

picture.

Q. When returning from multi-speed search to normalplayback, the picture is disturbed. Should I beconcerned about this?

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

A. No, it is normal.

Q. Noise bars appear during multi-speed search. What’sthe problem?

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

A. This is normal.

Q. When playing back programs that have been timer-recorded with consecutive times (such one programfrom 8:00 to 9:00 and another one from 9:00 to10:00), the picture and sound become momentarilydistorted at the point where the first program endsand the second program begins. Is this amalfunction?

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

A. No. This is normal.

Q. Other than preventing further recording, what effectdoes removing the safety tab have?

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

A. It disables marking of index codes.

Q. Sometimes, during Index Search, the VCR can’t findthe program I want to see. Why not?

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

A. There may be index codes too close together.

Q. During playback, on-screen operational indicatorssometimes jitter. Why does this happen?

A. If the condition of the tape being played back is notgood, jittering of the video (including on-screenindicators) may occur.

RECORDINGQ. When I pause and then resume a recording, the end

of the recording before the pause is overlapped bythe new recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

resume points.

Q. Can the VCR indefinitely remain in the Record-Pausemode?

A. No. The VCR automatically goes to its Stop modeafter 5 minutes to protect the heads. When pausedduring Instant Timer Recording (ITR), the VCR shuts

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

off automatically after 5 minutes.

Q. What happens if the tape runs out during recording?A. The VCR automatically rewinds it to the beginning.

TIMER RECORDINGQ. REC and ‰ remain lit on the front display panel. Is

there a problem?A. No. This is a normal condition for a timer recording

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

in progress.

Q. Can I program the timer while I’m watching a tapeor a TV broadcast?

A. Yes, but while you are setting the timer you won't seethe tape's or broadcast program's picture as it isreplaced by the on-screen menu. The audio from thetape or broadcast program will be present during thesetting of the timer.

48 EN INDEX

List Of TermsThis guide serves as a quick way to locate frequently used terms and on-screen display names.

AA/B Code ....................................................................44Add Channel ...............................................................15Audio Monitor ............................................................24Auto Channel Setting ..................................................14Auto Daylight Saving Time ..........................................12Auto Picture ................................................................26Auto SP→EP Timer ......................................................37Auto Timer ..................................................................37Automatic Tracking .....................................................20Aux Input ....................................................................40AV Connection .............................................................6

BBand ...........................................................................14

CCancel Program ..........................................................36Cassette Adapter.................................... ......................16Check Program ...........................................................36Connection to TV ..........................................................6Contents ........................................................................5Counter Reset ..............................................................22

DDelete Channel ...........................................................15

EEditing.........................................................................39Express Timer Programming ........................................34Express Timer Recording .............................................34

FFrame-by-Frame Playback ...........................................18GGuide Channel Setting ................................................33

HHost Channel Selection ...............................................12

IIndex Search ...............................................................19Insert Cassette .............................................................16Instant ReView ............................................................20ITR (Instant Timer Recording) ......................................38

LLanguage Selection .....................................................10

MMain Menu .................................................................10Manual Channel Setting ..............................................15Manual Clock Setting ..................................................13Manual Tracking .........................................................20MBR (Multi-Brand Remote) Code Setting.....................41Movie Advance ...........................................................25

NNext-Function Memory ...............................................22

OOn-Screen Display ......................................................23

PPBS Channel .................................................................8Playback .....................................................................16Plug & Play ...................................................................8

RRecord Safety Tab .......................................................17Recording ...................................................................17Repeat Playback..........................................................22Reverse Motion Playback ............................................18Reverse Slow Motion Playback ...................................18RF Connection ..............................................................6

SSAP (Second Audio Program) ......................................29Second Audio .............................................................29Semi-Auto Clock Setting..............................................12Skip Search .................................................................19Slow Motion Playback ................................................18Specifications ..............................................................52SQPB (S-VHS Quasi Play Back) ...................................16Still Picture Playback...................................................18Superimpose ...............................................................23

TTape Position Indicator ................................................22Tape Speed Setting ......................................................17Time Zone Selection ...................................................13Tuner Setting ...............................................................14

VVariable-Speed Search ................................................18VCR Plus+ Timer Programming ...................................30VCR Plus+ Timer Recording ........................................30Video Stabilizer ...........................................................21

EN 49FRONT VIEW

CH

MENUVIDEO (MONO)L–AUDIO–R

STOP/EJECT PAUSEREC

REW FFPLAYPOWER

OKSP

VCR

1

$#! @87

2 3 4 5

6 9 0

1 Power On/Off Button (Z pg. 10)2 Cassette Loading Slot3 Rewind [REW] Button (Z pg. 16)4 PLAY Button (Z pg. 16)5 Fast-Forward [FF] Button (Z pg. 16)6 VIDEO/AUDIO Input Connectors (Z pg. 40)

* The HR-VP450U has only one AUDIO input connector.7 MENU Button (Z pg. 10)

8 Front Display Panel (Z pg. 50)9 Remote Control Sensor0 Channel [CH] 5∞ Button (Z pg. 17)! OK Button (Z pg. 10)@ Record [REC] Button (Z pg. 17)# STOP/EJECT Button (Z pg. 16)$ PAUSE Button (Z pg. 18)

50 EN INDEX (cont.)

REAR VIEW

FRONT DISPLAY PANEL

SPVCR

4 5 6

1 2 3

ANT. IN

RF OUT

CH3 CH4

OUT

R

L

AUDIO

VIDEO

1

53

2

4

2 Tape Speed Indicators (Z pg. 17)3 Timer Mode Indicator4 VCR Mode Indicator (Z pg. 28)5 “Cassette Loaded” Mark6 Channel Display ["F-1" for AUX mode]

Counter Display (Z pg. 8)Clock Display (Z pg. 8)

1 Symbolic Mode Indicators

STILL:SLOW:

RECORD:

RECORD PAUSE:

PLAY:FF/REW VARIABLESEARCH:

1 Power Cord (Z pg. 6)2 ANT. IN Connector (Z pg. 6)3 Channel 3/4 Switch (Z pg. 6)

4 VIDEO/AUDIO Output Connectors (Z pg. 39)* The HR-VP450U has only one AUDIO output connector.

5 RF OUT Connector (Z pg. 6)

EN 51REMOTE CONTROL 1 CABLE/DBS Button (Z pg. 42, 43)

2 TV Button (Z pg. 41)3 TV/VCR Button (Z pg. 28)4 Instant REVIEW Button (Z pg. 20)5 NUMBER Buttons (Z pg. 17, 30)6 CANCEL Button (Z pg. 36)

Counter [C.] RESET Button (Z pg. 22)7 STOP +/– Button (Z pg. 34)8 START +/– Button (Z pg. 34)9 PROG. Button (Z pg. 30, 34)0 PROG. CHECK Button (Z pg. 36)! Rewind [REW] Button (Z pg. 16)@ Record [REC] Button (Z pg. 17)# STOP Button (Z pg. 16)$ MENU Button (Z pg. 10)% SHUTTLE PLUS %fi Button (Z pg. 10)

TV Channel [CH] +/– Button (Z pg. 41, 42, 43)^ MBR SET Button (Z pg. 41, 42, 43)

A/B Code Button (Z pg. 44)& POWER On/Off Button (Z pg. 10)* ENTER Button (Z pg. 17)

On-Screen Display [OSD] Button (Z pg. 23)( DISPLAY Button (Z pg. 22)) DAILY Timer Recording Button (Z pg. 31, 35)q WEEKLY Timer Recording Button (Z pg. 31, 35)w "AUX" Mode Select Button (Z pg. 40)e TIMER Button (Z pg. 31, 35)r DATE +/– Button (Z pg. 34)t Channel [CH] +/– Button (Z pg. 17, 35)y SKIP SEARCH Button (Z pg. 19, 25)u Recording Speed [SP/EP] Button (Z pg. 17)i PLAY Button (Z pg. 16)o Fast-Foward [FF] Button (Z pg. 16)p PAUSE Button (Z pg. 18)Q OK Button (Z pg. 10)W SHUTTLE PLUS ™£ ( ) Button

(Z pg. 18, 19)TV Volume [VOL.] +/– Button (Z pg. 41)

TV CH +

TV

VO

L–

TV CH –

TVVO

L+

TV

CANCEL TIMER

START STOP DATE

PLAYREW

REC STOP

SHUTTLEPLUS

PAUSE

FF

MENU OK

CH

POWER

TV/VCR

C. RESET

DAILY(M-F)

AUX

WEEKLY

PROGCHECK

PROG SP/EP SKIP SEARCH

DISPLAYENTER/OSD

CABLE/DBS

1 2 3

4 5 6

7 8 9

0

2

4

1

3

EXPRESS PROGRAMMING

MULTI BRANDREMOTE CONTROL UNIT

MBRSETA/B

ui

y

(

Q

1

3

76

2

8

4

9

5

0!@#$

^&*

ewq)

rt

po

%W

Buttons with a small dot on the left side of the name canalso be used to operate your TV while holding down the TVbutton. Z pg. 41

%fi

NOTES:● When inserting the batteries, be sure to insert in the correct

directions as indicated under the battery cover.● This remote control can also operate various brands of TVs,

Cable Boxes and DBS Receivers. For instructions,Z pg. 41 – 43.

● If the remote control doesn't work properly, remove itsbatteries, wait a short time, replace the batteries and thentry again.

How To UseThe remote control can operate most of your VCR'sfunctions.

1 Point the remote control toward the sensor window.2 Press the appropriate operation button.3 The maximum operating distance of the remote control

is about 8 m.

52 EN

GENERALPower requirement : AC 120 V` , 60 HzPower consumption

Power on : 22 W (HR-VP650U): 20 W (HR-VP450U)

Power off : 3 WTemperature

Operating : 5°C to 40°C (41°F to 104°F)Storage : –20°C to 60°C (–4°F to140°F)

Operating position : Horizontal onlyDimensions (W x H x D) : 360 x 94 x 273 mm

(14-3/16" x 3-3/4" x 10-3/4")Weight : 3.0 kg (6.6 lbs)Format : VHS NTSC standardMaximum recording time

SP : 210 min. with ST-210 videocassette

EP : 630 min. with ST-210 videocassette

VIDEO/AUDIOSignal system : NTSC-type color signal and

EIA monochrome signal, 525lines/60 fields

Recording/Playback system : DA-4 (Double Azimuth) head

helical scan systemSignal-to-noise ratio : 45 dBHorizontal resolution : 240 linesFrequency range

Normal audio : 70 Hz to 10,000 HzHi-Fi audio(HR-VP650U only) : 20 Hz to 20,000 Hz

Input/Output : RCA connectors(IN x 1, OUT x 1)

TUNERTuning system : Frequency-synthesized tunerChannel coverage

VHF : Channels 2–13UHF : Channels 14–69CATV : 113 Channels

RF output : Channel 3 or 4 (switchable;preset to Channel 3 whenshipped) 75 ohms,unbalanced

SPECIFICATIONS

TIMERClock reference : QuartzProgram capacity : 1-year programmable timer/

8 programsMemory backup time : Approx. 10 min.

ACCESSORIESProvided accessories : RF cable (F-type),

Infrared remote control unit,“AA” battery x 2

Specifications shown are for SP mode unless otherwise specified.E. & O.E. Design and specifications subject to change withoutnotice.

EN 53HOW TO LOCATE YOUR JVC SERVICE CENTER

TOLL FREE: 1-800-252-5722

JVC SERVICE & ENGINEERINGCOMPANY OF AMERICA

DIVISION OF US JVC CORP.

FACTORY SERVICE CENTER LOCATIONS

If you ship the product...

ACCESSORIES

107 Little Falls Road 1500 Lakes Parkway 705 Enterprise StreetFairfield, NJ 07004-2105 Lawrenceville, GA 30243-5857 Aurora, IL 60504-8135(973) 808-9279 (770) 339-2522 (630) 851-7855

5665 Corporate Avenue 10700 Hammerly Boulevard, Suite 110 2969 Mapunapuna Place, Suite 101Cypress, CA 90630-4727 Houston, TX 77043-2310 Honolulu, HI 96819-2000(714) 229-8011 (713) 935-9331 (808) 833-5828

230 Eliot Street 8192 W State Road 84 890 Dubuque AvenueAshland, MA 01721-2377 Davie, FL 33324-4611 South San Francisco, CA 94080-1804(508) 881-5923 (954) 472-1960 (415) 871-2666

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and productionof the wide array of JVC products, service is the key to maintaining the high level performance for which JVC is world famous. TheJVC service and engineering organization stands behind our products.

NATIONAL HEADQUARTERSJVC SERVICE & ENGINEERING COMPANY OF AMERICA

DIVISION OF US JVC CORP.107 Little Falls Road

Fairfield, NJ 07004-2105

Pack your JVC unit in the original carton or one of equivalentsize and strength. Enclose, with the unit, a letter stating theproblem or symptom that exists and also a copy of the receiptor bill of sale you received when you purchased your JVCunit. Print your home return address on the outside and theinside of the carton. Send to the appropriate JVC FactoryService Center as listed above.

To purchase accessories for your JVC product, you maycontact your local JVC Dealer.Or from the 48 Continental United States call toll free:1-800-882-2345.

Dear customer:In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the eventthat repair is necessary, or for the address nearest your location, please refer to the factory service center list below or within theContinental United States, call 1-800-252-5722 for your authorized servicer. Remember to retain your Bill of Sale for WarrantyService.

— JVC

CAUTIONTo prevent electrical shock, do not open the cabinet. No userserviceable parts inside.Refer servicing to qualified service personnel.

Don't service it yourself.

FOR SERVICING (Only in U.S.A.)

54 EN

LIMITED WARRANTY CONSUMER VIDEO 1-90

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINALPURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retailpurchase for the period as shown below. ("The Warranty Period")

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND INCOMMONWEALTH OF PUERTO RICO.

WHAT WE WILL DO:If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repairand replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Partsused for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may bebrought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches andabove which are covered on an in-home basis.

WHAT YOU MUST DO FOR WARRANTY SERVICE:Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorizedservice center, please call toll free: (800) 252-5722.If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy ofyour bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and locationof which will be given to you by the toll-free number.

If you have any questions concerning your JVC Product, please contact our Customer Relations Department.

WHAT IS NOT COVERED:This limited warranty provided by JVC does not cover:1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty

installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC torender such service, or if affixed to any attachment not provided with the products, or if the model or serial number has beenaltered, tampered with, defaced or removed;

2. Initial installation and installation and removal for repair;3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;4. Damage that occurs in shipment, due to act of God, and cosmetic damage;5. Signal reception problems and failures due to line power surge;6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;7. Accessories;8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase); from the date of purchase);

There are no other express warranties except as listed above.

THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, ISLIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.

JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHERDAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TOTAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACHOF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OFMERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SETFORTH ABOVE.

Some states do not allow the exclusion of incidental or consequential dameges or limitations on how long an implied warrantylasts, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may alsohave other rights which vary from state to state.

JVC COMPANY OF AMERICA 41 Slater DriveDIVISION OF US JVC CORP. Elmwood Park, New Jersey 07407

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OFREFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATIONPACKAGED WITH EACH REFURBISHED PRODUCT.

For customer use:Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information for futurereference.

Model No.: Serial No.:

Purchase date: Name of dealer:

PARTS LABOR1 YR 90 DAYS

WARRANTY (Only in U.S.A.)

EN 55MEMO

HR

-VP

65

0U

/45

0U

COPYRIGHT © 1998 VICTOR COMPANY OF JAPAN, LTD. U/U(C) Printed in Malaysia0198 IYV*UN*PJ

JVC COMPANY OF AMERICADIVISION OF US JVC CORP.

41 Slater Drive, Elmwood Park, N.J. 07407

JVC CANADA INC.21 Finchdene Square, Scarborough Ontario M1X 1A7

VIDEO CASSETTE RECORDER HR-VP650U (Hi-Fi) HR...

Documents

Transcript of VIDEO CASSETTE RECORDER HR-VP650U (Hi-Fi) HR...