Vertically Polarized Panels - WPA-RWA-RWB Series
of 150
-
Upload
hirak-jyoti-mazumdar -
Category
Documents
-
view
358 -
download
4
Transcript of Vertically Polarized Panels - WPA-RWA-RWB Series
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
1/150
Vertically Polarized Directional Panel Antennas
806-900 MHz, 806-960 MHz
Model NumberFrequency Range
(MHz)H-Plane E-Plane
Gain
(dBd)
Fixed Electrical
Downtilt Options
Length x Width x Depth
(in inches)
WPA-80063/2CF _ 806-900 MHz 63 30 10 dBd 0 23.8 x 11.8 x 3.9
WPA-80063/4CF _ 806-960 MHz 63 16 13 dBd 0,2,5 47.4 x 11.8 x 3.9
WPA-80063/6CF _ 806-960 MHz 63 11 14.5 dBd 0,5 71.0 x 11.8 x 3.9
WPA-80063/8CF _ 806-960 MHz 63 7 16.5 dBd 0,2, 5,10 94.7 x 11.8 x 3.9
WPA-80080/2CF _ 806-900 MHz 80 30 9.5 dBd 0 23.8 x 11.2 x 4.5
WPA-80080/4CF _ 806-960 MHz 80 15 12 dBd 0,5 47.4 x 11.2 x 4.5
WPA-80080/6CF _ 806-960 MHz 80 11 13.5 dBd 0,4 71.1 x 11.2 x 4.5
WPA-80080/8CF _ 806-960 MHz 80 7 15 dBd 0,5 94.7 x 11.2 x 4.5
WPA-80090/2CF _ 806-900 MHz 90 30 9 dBd 0 23.8 x 8.1 x 5.7
WPA-80090/4CF _ 806-960 MHz 90 15 11.5 dBd 0,5 47.4 x 8.1 x 5.7
WPA-80090/6CF _ 806-960 MHz 90 11 13 dBd 0,5 71.1 x 8.1 x 5.7
WPA-80090/8CF _ 806-960 MHz 90 7 14.5 dBd 0,5 94.7 x 8.1 x 5.7
WPA-800120/6CF _ 806-960 MHz 120 11 12 dBd 0,5 70.9 x 5.6 x 5.6
WPA-800 Series
The WPA (Wideband Panel Antenna) is a directional antenna operating within the 806-900 MHz and 806-960 MHz frequency range
These vertically polarized panel antennas are light-weight and low-profile and offer excellent upper side lobe suppression and hor
izontal roll-off. WPAs are ideal for sectorized sites in which cost is a factor and tower issues are present. Antennas are availablewith fixed electrical downtilt.
Design and Cons truct ion of the WPA-800 Panel:
WPA antennas are manufactured with our exclusive 3T Technology, featuring single-piece, water-cut brass feedline assemblies fo
consistent performance; a non-collinear system with access to each radiating element for control of the shaping of the vertical pat
tern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even
heat dissipation to minimize plate warping and bending.
Model Number Guide:
Amphenol Antel, Inc.
Models Currently Available:
WPA- 800 63 / 8 CF E-DIN 5
Electrical Downtilt
Connector Type
NE is an elongated N connector
E-DIN is an elongated DIN connector
BF refers to a Bottom-Fed connector
CF refers to a Center-Fed connector
TF refers to a Top-Fed connector
Number of radiating element sets
Also refers to the approx. length in feet
Horizontal Beamwidth
Operating Frequency Range800 = Operates within 806-960 MHz
When ordering replace __ with the connector type (NE or E-DIN).
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
2/150
Vertically Polarized, Panel 63 / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/2CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 604 mm 23.8 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)Weight 3.2 kg 7.0 lbs
Wind Area
Fore/Aft 0.18 m2 1.95 ft2
Side 0.06 m2 0.65 ft2
Rated Wind Velocity (Safety factor 2.0)
>486 km/hr >302 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 257 N 57.8 lbs
Side 88 N 19.7 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-900 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 10 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 301)
Electrical Downtilt 01)
Null Fill 0%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
3/150
Vertically Polarized, Panel 63 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/4CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1205 mm 47.4 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.36 m2 3.9 ft2
Side 0.12 m2 1.3 ft2
Rated Wind Velocity (Safety factor 2.0)
>431 km/hr >267 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 516 N 116.0 lbs
Side 194 N 43.7 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 13 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 161)
Electrical Downtilt 01)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
4/150
Vertically Polarized, Panel 63 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/4CF __ 2
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1205 mm 47.4 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.36 m2 3.9 ft2
Side 0.12 m2 1.3 ft2
Rated Wind Velocity (Safety factor 2.0)
>431 km/hr >267 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 516 N 116.0 lbs
Side 194 N 43.7 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 13 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 161)
Electrical Downtilt 21)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
5/150
Vertically Polarized, Panel 63 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/4CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1205 mm 47.4 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.36 m2 3.9 ft2
Side 0.12 m2 1.3 ft2
Rated Wind Velocity (Safety factor 2.0)
>431 km/hr >267 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 516 N 116.0 lbs
Side 194 N 43.7 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 13 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 161)
Electrical Downtilt 51)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
6/150
Vertically Polarized, Panel 63 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/6CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1804 mm 71.0 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in4)
Weight 6.8 kg 15.0 lbs
Wind Area
Fore/Aft 0.54 m2 5.8 ft2
Side 0.18 m2 1.9 ft2
Rated Wind Velocity (Safety factor 2.0)
>459 km/hr >284 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 791 N 177.9 lbs
Side 322 N 72.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 14.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 111)
Electrical Downtilt 01)
Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
7/150
Vertically Polarized, Panel 63 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/6CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1804 mm 71.0 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in4)
Weight 6.8 kg 15.0 lbs
Wind Area
Fore/Aft 0.54 m2 5.8 ft2
Side 0.18 m2 1.9 ft2
Rated Wind Velocity (Safety factor 2.0)
>459 km/hr >284 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 791 N 177.9 lbs
Side 322 N 72.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 14.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 111)
Electrical Downtilt 51)
Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
8/150
Vertically Polarized, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/8CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m2 7.8 ft2
Side 0.24 m2 2.6 ft2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 16.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 71)
Electrical Downtilt 01)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
9/150
Vertically Polarized, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/8CF __ 2
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m2 7.8 ft2
Side 0.24 m2 2.6 ft2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 16.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 71)
Electrical Downtilt 21)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
10/150
Vertically Polarized, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/8CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m2 7.8 ft2
Side 0.24 m2 2.6 ft2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 16.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 71)
Electrical Downtilt 51)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
11/150
Vertically Polarized, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80063/8CF __ 10
Revision Date: 8/9/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-941 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m2 7.8 ft2
Side 0.24 m2 2.6 ft2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-941 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 16.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 63
E-Plane 71)
Electrical Downtilt 101)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
12/150
Vertically Polarized, Panel 80 / 9.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80080/2CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 604 mm 23.8 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in4)
Weight 2.2 kg 4.9 lbs
Wind Area
Fore/Aft 0.18 m2 1.80 ft2
Side 0.07 m2 0.76 ft2
Rated Wind Velocity (Safety factor 2.0)
>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 248 N 56 lbs
Side 102 N 23 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-900 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 9.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 80
E-Plane 301)
Electrical Downtilt 01)
Null Fill 0%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
13/150
Vertically Polarized, Panel 80 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80080/4CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1205 mm 47.4 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in4)
Weight 4.5 kg 9.9 lbs
Wind Area
Fore/Aft 0.36 m2 3.9 ft2
Side 0.15 m2 1.6 ft2
Rated Wind Velocity (Safety factor 2.0)
>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 522 N 117 lbs
Side 233 N 52 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 12 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 80
E-Plane 151)
Electrical Downtilt 01)
Null Fill 5-10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
14/150
Vertically Polarized, Panel 80 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80080/4CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1205 mm 47.4 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in4)
Weight 4.5 kg 9.9 lbs
Wind Area
Fore/Aft 0.36 m2 3.9 ft2
Side 0.15 m2 1.6 ft2
Rated Wind Velocity (Safety factor 2.0)
>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 522 N 117 lbs
Side 233 N 52 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 12 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 80
E-Plane 151)
Electrical Downtilt 51)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
15/150
Vertically Polarized, Panel 80 / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80080/6CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1804 mm 71.1 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in4)
Weight 6.8 kg 14.9 lbs
Wind Area
Fore/Aft 0.54 m2 5.8 ft2
Side 0.21 m2 2.3 ft2
Rated Wind Velocity (Safety factor 2.0)
>438 km/hr >272 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 790 N 178 lbs
Side 353 N 80 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 13.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 80
E-Plane 111)
Electrical Downtilt 01)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
16/150
Vertically Polarized, Panel 80 / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80080/6CF __ 4
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1804 mm 71.1 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in4)
Weight 6.8 kg 14.9 lbs
Wind Area
Fore/Aft 0.54 m2 5.8 ft2
Side 0.21 m2 2.3 ft2
Rated Wind Velocity (Safety factor 2.0)
>438 km/hr >272 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 790 N 178 lbs
Side 353 N 80 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 13.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 80
E-Plane 111)
Electrical Downtilt 41)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
17/150
Vertically Polarized, Panel 80 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80080/8CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2405 mm 94.7 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in4)
Weight 10.9 kg 24.0 lbs
Wind Area
Fore/Aft 0.70 m2 7.5 ft2
Side 0.28 m2 3.0 ft2
Rated Wind Velocity (Safety factor 2.0)
>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1048 N 236 lbs
Side 510 N 115 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 15 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 80
E-Plane 71)
Electrical Downtilt 01)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
18/150
Vertically Polarized, Panel 80 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80080/8CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2405 mm 94.7 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in4)
Weight 10.9 kg 24.0 lbs
Wind Area
Fore/Aft 0.70 m2 7.5 ft2
Side 0.28 m2 3.0 ft2
Rated Wind Velocity (Safety factor 2.0)
>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1048 N 236 lbs
Side 510 N 115 lbs
Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 15 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 80
E-Plane 71)
Electrical Downtilt 51)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
19/150
Vertically Polarized, Panel 90 / 9 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80090/2CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-900 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 604 mm 23.8 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in4)
Weight 2.1 kg 4.6 lbs
Wind Area
Fore/Aft 0.12 m2 1.33 ft2
Side 0.09 m2 0.92 ft2
Rated Wind Velocity (Safety factor 2.0)
>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 176 N 39.5 lbs
Side 122 N 27.5 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36211102
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-900 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 9 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 90
E-Plane 301)
Electrical Downtilt 01)
Null Fill 0%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
20/150
Vertically Polarized, Panel 90 / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80090/4CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1205 mm 47.4 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in4)
Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.25 m2 2.7 ft2
Side 0.17 m2 1.9 ft2
Rated Wind Velocity (Safety factor 2.0)
>679 km/hr >422 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 362 N 81.4 lbs
Side 264 N 59.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 11.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 90
E-Plane 151)
Electrical Downtilt 01)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
21/150
Vertically Polarized, Panel 90 / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80090/4CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1205 mm 47.4 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in4)
Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.25 m2 2.7 ft2
Side 0.17 m2 1.9 ft2
Rated Wind Velocity (Safety factor 2.0)
>679 km/hr >422 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 362 N 81.4 lbs
Side 264 N 59.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 11.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 90
E-Plane 151)
Electrical Downtilt 51)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
22/150
Vertically Polarized, Panel 90 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80090/6CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1805 mm 71.1 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in4)
Weight 8.2 kg 18.0 lbs
Wind Area
Fore/Aft 0.37 m2 3.9 ft2
Side 0.26 m2 2.8 ft2
Rated Wind Velocity (Safety factor 2.0)
>452 km/hr >281 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 558 N 126.0 lbs
Side 433 N 97.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 13 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 90
E-Plane 111)
Electrical Downtilt 01)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
23/150
Vertically Polarized, Panel 90 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80090/6CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 1805 mm 71.1 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in4)
Weight 8.2 kg 18.0 lbs
Wind Area
Fore/Aft 0.37 m2 3.9 ft2
Side 0.26 m2 2.8 ft2
Rated Wind Velocity (Safety factor 2.0)
>452 km/hr >281 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 558 N 126.0 lbs
Side 433 N 97.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 13 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 90
E-Plane 111)
Electrical Downtilt 51)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
24/150
Vertically Polarized, Panel 90 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80090/8CF __
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2405 mm 94.7 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in4)
Weight 10.4 kg 23.0 lbs
Wind Area
Fore/Aft 0.49 m2 5.3 ft2
Side 0.35 m2 3.8 ft2
Rated Wind Velocity (Safety factor 2.0)
>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 793 N 178.4 lbs
Side 591 N 132.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 14.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 90
E-Plane 71)
Electrical Downtilt 01)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
25/150
Vertically Polarized, Panel 90 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-80090/8CF __ 5
Revision Date: 7/2/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.
Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.
806-960 MHz
Amphenol An tel s
Exclusive 3T (True
Transmission L ine
Technology)
Antenna Des ign:
This Amphenol Antel antenna is under a fiv
year limited warranty for repair or replacemen
Mechanical specificationsLength 2405 mm 94.7 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in4)
Weight 10.4 kg 23.0 lbs
Wind Area
Fore/Aft 0.49 m2 5.3 ft2
Side 0.35 m2 3.8 ft2
Rated Wind Velocity (Safety factor 2.0)
>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 793 N 178.4 lbs
Side 591 N 132.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and DowntiltingMounting brackets attach to a pipe diameter of50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002Downtilt bracket kit #36114003
Electrical specifications
1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 503)
Connector(s) NE or E-DIN
1 port / center1)
VSWR 1.4:1
Polarization Vertical1)
Gain 14.5 dBd2)
Power Rating 500 W1)
Half Power Angle
H-Plane 90
E-Plane 71)
Electrical Downtilt 51)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-FedConnector.
Watercut brass feedline assembly forconsistent performance.
Unique feedline design eliminates the neefor conventional solder joints in the signalpath.
A non-collinear system with access toevery radiating element for broad band-width and superior performance.
Air as insulation for virtually no internalsignal loss.
Antenna avai lable w ith center-fed
connector only.
-
7/27/2019 Vertically Polarized Panels - WPA-RWA-RWB Series
26/150
Vertically Polarized, Panel 120 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 [email protected] www.antelinc.com
WPA-800120/6CF __
Revision Date: 7/12/0
When ordering replace ___ with connector typ
0
10
20
30
40
50
60
70
8090100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110-100 -90 -80
-70
-60
-50
-40
-30
-20
-10
5101520253035
Radiation pattern1)
Horizontal
0
10
20
30
40
5060
708090100
110
120130
140
150
160
170
180
-170
-160
-150
-140
