Versymmetric 2-Pos tLifts

www.challengerlifts.com

Model Number CL9 CL9-1 CL9-2 CL10 CL10-2 CL10-3Lifting Capacity 9,000 lbs. 9,000 lbs. 9,000 lbs. 10,000 lbs. 10,000 lbs. 10,000 lbs.Rise Height* 745/8" 745/8" Adjustable Column Height 11' 8" or 11' 2" 12' 8" or 12' 2" 13' 8" or 13' 2" 11' 8" 13' 8" 14' 8"Cylinder Overall (Full Stroke) 11' 11" 11' 11" Adjustable Width Overall 11' 2" / 10' 8" / 10' 2" 11' 11" / 11' 61/2"Drive-Thru Clearance** 893/8" 105" / 1001/2"Floor to Overhead Switch** 11' 23/8" 12' 23/8" 13' 23/8" 11' 2½" 13' 2½" 14' 2½"Front Arm Reach (Min./Max.) Min. 27" / Max. 41" Min. 27" / Max. 41"Rear Arm Reach (Min./Max.) Min. 381/4" / Max. 59" Min. 42" / Max. 59"Screw Pad Height Adj. 41/8" - 65/8" Adj. 41/8" - 65/8"Inside Columns** 109" 1141/2" / 110"Motor 2HP 2HP Voltage (Single Phase Std.)*** 208v-230v 208v-230v Speed of Rise 48 Sec. 48 Sec. Ceiling Height Required 12' 12' 9" 13' 9" 11' 11" 13' 9" 14' 9"

- ALL MODELS INCLUDE A SINGLE-POINT “MECHANICAL” LOCK RELEASE SYSTEM. - ADJUSTABLE "RUBBER PAD" ARMS STANDARD, 3-POSITION FLIP-UP FRAME CONTACT ARMS ARE AVAILABLE BY ADDING "SP" AFTER PART NUMBER AT TIME OF ORDER (Example CL9SP). * Rise height is measured with adjustable screw pads in highest position. ** Specifications are listed with lift at MAXIMUM width and/or height settings. *** Optional 3 phase electrical also available, please specify at time of order. Standard lift colors are Red and Blue

Versymmetric® 2-Post Lifts(Asymmetric and Symmetric Lifting)

Part#: 10300

Part#: 10264

optional accessories:

Part Number Description10300 Two luxury car adapters.10303 Two 6" slip-on extension pads10304 Two 10" slip-on extension pads

10305 Four 6" slip-on extension pads with organizer kit10306 Organizer kit

10264 Air/electric workstation with filter/lubricator/regulator

10201 Air/electric work station without filter/lubricator/regulator16621 Two 5" Flip-up truck adapters

Part#: 10304Part#: 10303

Model #: CL10Symmetric Application

Model #: CL10Asymmetric application

• Double your service capabilities. Our heavy-duty arms are specially engineered to lift vehicles both “asymmetrically” and “symmetrically” in the same bay to increase servicing flexibility and revenue potential.

• Several adjustable (width and/or height) features make this lift the “perfect fit” for your service bay.

• Our overhead cable equalization system and small base plate provides a clear floor environment so tools can be moved easier and minimizes obstructions.

• Technicians can save valuable time by disengaging both column locks at the same time with our single-point lock release system.

• User friendly arm restraints automatically disengage when lift is fully lowered for easy positioning of arms and securely engage when lift is raised.

TM

Part#: 16621


Model Number 12000 12001 12002 15000 15002 18000 18002 Lifting Capacity 12,000 lbs. 12,000 lbs. 12,000 lbs. 15,000 lbs. 15,000 lbs. 18,000 lbs. 18,000 lbs. Rise Height* 843/4" 851/2" 851/2" Height Overall 13' 8" 14' 8" 15' 8" 14' 6" 16' 6" 14' 6" 16' 6" Width Overall 11' 10" 12' 103/4" 12' 103/4" Drive-Thru Clearance 1041/2" 1063/4" 1063/4" Floor to Overhead Switch 13' 1" 14' 1" 15' 1" 13' 11" 15' 11" 13' 11" 15' 11" Arm Reach (Min.) 37" 381/2" 381/2" Arm Reach (Max.) 54" 62" 62" Screw Pad Height 5" - 63/4" 61/4" - 81/2" Medium Extension 8" - 93/4" 101/4" - 121/2" High Extension 11" - 123/4" 141/4" - 161/2" Inside Columns 1141/2" 120" 120" Air Supply Required 85-115 psi 85-115 psi 85-115 psi Motor 2HP 2HP 2HP Voltage (Single Phase Std.)** 208v-230v 208v-230v 208v-230v Speed of Rise 60 Sec. 80 Sec. 80 Sec. Ceiling Height Required 13' 9" 14' 9" 15' 9" 14' 7" 16' 7" 14' 7" 16' 7"

Heavy Duty 2-Post Lifts(Symmetric Lifting)

Model #: 18000

4 standard adapters

4 medium extensions

2 high extensions

standard accessories:Technicians can

disengage both columns at the same time with

our single-point air actuated lock release.

Our single push button power unit raises lift and a release valve handle lowers it.

Challenger’s arm restraints automatically disengage when lift is fully lowered for easy positioning of arms and securely engage when lift is raised.

Turn your lift into a workstation with our

Optional Air-Electric Service Station. (Part#: 10264)

Our single piece adapter organizer prevents adapters

from being misplaced.

Whether you want to expand your fleet service capabilities, avoid downtimes or just increase your bottom line, Challenger Lift’s 12,000, 15,000, and 18,000 lbs. heavy-duty 2-post lifts are the solutions for your servicing needs.

Not only does our Heavy-Duty Series lift a lot, it’s a lot of lift. With features that you would expect to pay more for, like padded overhead cut-off bar, adapter accessories, etc. In fact no other lift company gives you more.

Lit#: AN1B-1_9/05

* Rise height is measured with adjustable screw pads in highest position. ** Optional 3 phase electrical also available, please specify at time of order. Standard lift colors are Red and Blue


Should liquid ever accumulate in the bottom of your cassette lift, Challenger Lifts’ EnviroVAC – Evacuation System will help protect your investment and minimize expensive service call by giving you the ability to easily remove the unwanted liquid immediately into a 16 gallon container.

• A powerful pump allows quick liquid removal

• Container easily rolls to a quick-connect evacuation hose next to power unit

• Container incorporates a drain valve to conveniently dispose evacuated liquid

• Retrofi ts with other cassette lift models, including competitive brands

Challenger Lifts’ DeTEK - Liquid Detection System informs you should liquid ever accumulate in the bottom of your inground cassette tub.

• Detects liquid as low as 13/4"

• Red detection light system mounts securely to power unit for easy visibility

• Retrofits with other cassette lift models, including competitive brand

Model #: EVAC1

Model #: DTLS1

Model #: CS1020W * Standard models includes an adjustable screw-type rubber pad or 3-position flip-up superstructure. Please specify superstructure preference at time of order.** Rise height is measured with superstructure in highest position.***Optional 3 phase electrical also available, please specify at time of order.

Model Numbers CS1020W* CS1220 CS1520Lifting Capacity 10000 lbs. 12000 lbs. 15000 lbs.Rise Height** 78" 811/4" 843/4"Stroke 68" 68" 68"Width Overall 97" 99" 711/2"Drive-Thru Clearance 87" 88" NAReach (Arm Minimum) 261/2" 32" 261/4"Reach (Arm Maximum) 39" 491/4" 43"Min. Adapter Height 4" NALow Step Height 61/2" NAHigh Step Height 10" NAAdapter Height NA Adj. 5" - 71/4" Adj. 61/2" - 83/4"Adapter Height (w/Med. Ext.) NA Adj. 8" - 101/4" Adj. 101/2" - 12 3/4"Adapter Height (w/High. Ext.) NA Adj. 11" - 131/4" Adj. 141/2" - 163/4"Capacity (Per Arm) 2500 lbs. 3000 lbs. 3750 lbs.Motor 2HP 2HP 2HPVoltage (Single Phase Std.)*** 208v-230v 208v-230v 208v-230vSpeed of Rise 48 Seconds 65 Seconds 80 SecondsAir Required 75 - 125 psi 75 - 125 psi 75 - 125 psiRecommended 79" plus height 82" plus height 85" plus heightCeiling Height of tallest vehicle of tallest vehicle of tallest vehicle

Standard Heavy-Duty

3 position fl ip-ups:

Part#: 10300

Part Number Description10300 Two luxury car adapters.10303 Two 6" slip-on extension pads10304 Two 10" slip-on extension pads10305 Four 6" slip-on extension pads with organizer kit16621 Two 5" Flip-up truck adapters

Part#: 10304

Part#: 10303

Part#: 16621

Three height positions:low, medium, and high.


adjustable screw pads:

Reach ranging between highest and lowest screw positions


Part Number Description24006C Two 6,000 lbs. rolling jacks40230 Internal air-line kit

10500SS Two flush mounted stainless steel turning radius gauges

Alignment Rack Packages Include

Four Post lifts

Model #: 40SFX

Model Number AR40EAO AR40XAO AR40EAX AR40XAXLifting Capacity 12,000 lbs. 12,000 lbs. 12,000 lbs. 12,000 lbs.Max. Wheelbase 1821/2" 210" 1821/2" 210"Max. 2 Wheel Align. 1661/2" 194" 1661/2" 194"4 Wheel Align. 88" - 158" 88" - 158"Rise Height 79" 79" Length Overall 20' 9" 23' 20' 4" 22' 8"Width Overall 11' 10" 10' 11" Inside Columns 120" front - 116" rear 116" Height of Columns 991/2" front - 901/2" rear 901/2" Width of Runways 20" 20" Height of Runways 7" 7" Air Supply Required 85-115 psi 85-115 psi Motor 2HP 2HP Voltage (1 Phase Std.)** 208v-230v 208v-230v Speed of Rise 70 Sec. 70 Sec.

Open-Front Closed-Front

* Maximum wheelbase is based on a tire diameter of 30". ** Optional 3 phase electrical also available. Standard lift colors are Red and Blue.

Model #: AR40XAO

Alignment Rack Packages50" Max.33" Min.

153/8" Max. 33/8" Min.

43" Max.40" Min.

Model Number 40NFX 40SFX 40EFX 40XFX 40EFO 40XFO Lifting Capacity 12,000 lbs. 12,000 lbs. 12,000 lbs. 12,000 lbs. 12,000 lbs. 12,000 lbs. Max. Wheelbase* 1571/2" 1571/2" 1821/2" 210" 182½" 210" Rise Height 79" 79" 79" 79" 79" 79" Length Overall 18' 3" 18' 3" 20' 4" 22' 8" 20' 9" 23' Width Overall 10' 1" 10' 11" 10' 11" 10' 11" 11' 10" 11' 10" Inside Columns 106" 116" 116" 116" 120" front - 116" rear Height of Columns 90½" 90½" 90½" 90½" 99½" front - 90½" rear Width of Runways 20" 20" 20" 20" 20" 20" Height of Runways 7" 7" 7" 7" 7" 7" Air Supply Required 85-115 psi 85-115 psi 85-115 psi 85-115 psi 85-115 psi 85-115 psi Motor 2HP 2HP 2HP 2HP 2HP 2HP Voltage (1 Phase Std.)** 208v-230v 208v-230v 208v-230v 208v-230v 208v-230v 208v-230v Speed of Rise 70 Sec. 70 Sec. 70 Sec. 70 Sec. 70 Sec. 70 Sec.

Narrow Standard Extended XL Extended Open Front Open Front Bay Length Length Length Extended XL Extended


standard accessories:

Part Number Description10266 Drive through ramps24006C 6,000 lbs. rolling jack10267 32 gal. rolling drain pan40230(X)(E)(S) Internal air line kit

40200-3D 3D alignment compatible w/o radius gauges 3D alignment compatible40200-3DBK w/black “powder coat” radius gauges(10500HD) 3D alignment compatible40200-3DSS w/stainless steel radius gauges(10500SS)

Bolt-on Alignment Kits

Part#: 24006C

Lit#: AN1B-2_9/05

* Maximum wheelbase is based on a tire diameter of 30". ** Optional 3 phase electrical also available. Standard lift colors are Red and Blue.

Built in rear slip plates and two multi-position worksteps are also included with the purchase of any Alignment Rack Package


Model Number 67000Lifting Capacity 6,000 lbs.Rise Height 26"Lowered Minimum Height 41/4"Locking Bar Heights 131/2" / 181/2" / 211/2" Width Overall 72"Length Overall 901/4"Rearward Movement 13"Motor 1HPVoltage (Single Phase Std.) 115vSpeed of Rise 45 Sec.

Portable Mid-Rise LiftModel Number 66000 66000ALifting Capacity 6,000 lbs. 6,000 lbs.Rise Height 48" 48"Length Overall 7' 6" 7' 6"Width Overall 3' 33/8" 3' 33/8"Min. Collapsed Height 33/8" 33/8"Pad Height (Min.) 51/2" 51/2Pad Height (Max.) 491/2" 491/2Hydraulic Hose 12' 12'Lock Positions 4 4Electric Motor 1HP NAVoltage (Single Phase) 115v NAAir Supply Required NA 100 psiPneumatic Motor NA 2HPSpeed of Rise 45 Sec. 65 Sec.

Pit Lift

Short-Rise Pad Lift

Model #: 67000

4 spotting blocksPart #: 68005-1

Four 4 1/8" spotter blockauxiliary adapters

Part #: 63100

Model #: 66000

Model #: 68000

Low Ceiling 2-Post(Symmetric Lifting)

Model Number 26000 Lifting Capacity 9,000 lbs. Rise Height 781/2" Column Height 10' 1" Width Overall 10' 101/2" Drive-Thru Clearance 98" Arm Reach (Min.) 28 3/4" Arm Reach (Max.) 44 1/2" Screw Pad Height Adj. 6" - 8" Inside Columns 109" Motor 2HP Voltage (Single Phase Std.) 208v-230v Speed of Rise 45 Sec. Reference Versymmetric page for optional accessories. Standard lift colors are Red and Blue.Model #: 26000

Model Number 68000Lifting Capacity 6,000 lbs.Rise Height 25"Lowered Minimum Height 5"Locking Bar Heights 24" / 19" / 141/2" Width Overall (plus pit width) 37"Length Overall 853/4"Spotting Blocks(4 included) 1½" x 4" x 6¼"Motor 1HPVoltage (Single Phase Std.) 115vSpeed of Rise 40 Sec. Hoses provided by installer. Standard lift color is Blue only.

standard accessories:

4 rubber pad adapters and

height extensions included


standard accessories:The 68000 pit lift is hydraulically equalized allowing for an obstruction free pit.

Standard lift colors are Red and Blue.

Standard lift colors are Red and Blue.

Model Number Q10000Lifting Capacity 10,000 lbs.Rise Height* 781/2"Adjustable Column Height 12' 3½" or 11' 5½"Cylinder Overall (Full Stroke) 12' 4"Width Overall 1353/4"Drive-Thru Clearance 98½"Floor To Overhead Switch 11' 9" or 10' 113/4"Front Arm Reach (Min./Max.) Min. 221/2" / Max. 42"Rear Arm Reach (Min./Max.) Min. 391/2" / Max. 611/2"Screw Pad Height Adj. 5" - 9"Inside Columns 113"Motor 2HPVoltage (Single Phase Std.) 208v-230vSpeed of Rise 50 SecondsCeiling Height Required 12' 5"

Asymmetric/SymmetricCombination Lift

*Rise height is measured with screw pads in highest position.

• BOTH “asymmetric” and “symmetric” lifting capabilities to service a wider variety of vehicles in the same bay.

• Automatic arm restraints

• Overhead shutoff system

• Adjustable height

Model #: Q10000Symmetric Application

Model #: Q10000Asymmetric Application

Heavy Duty Two-Post Lift(symmetric lifting)

6" Truck Adapter PairPart #: TKAE

Buy Quality™

Model Number Q12000Lifting Capacity 12,000 lbs.Rise Height* 80"Adjustable Column Height 14' 7" or 13' 10"Width Overall 137 3/4"Drive-Thru Clearance 101"Floor To Overhead Switch 14' 4" or 13' 7"Front / Rear Arm Reach Min. 3113/16" / Max. 5411/16"Screw Pad Height Adj. 5" - 9"Inside Columns 114 9/16"Motor 2HPVoltage (Single Phase Std.) 208v-230vSpeed of Rise 65 SecondsCeiling Height Required 14' 8" * Rise height is measured with screw pads in highest position.

5" Slip-on TruckAdapter PairPart #: TKA5

Optional Accessory:

Optional Accessory:

Model #: Q12000

Lit#: AN1B-3_9/05

DUAL PENDANT CONTROL

Handheld pendant control tethered to both columns. Activates the raise and lowering functions of the power unit.

Single point mechanical lock release operates from both sides of the lift.

Allows the technician the ability to raise and lower the lift from both sides while spotting the arms, when small adjustments can matter most!

Each magnetic backed pendant can be located on its’ column anywhere above 18½.

Installation friendly for New CL9 and CL10 Versymmetric® 2-Post Lift Models.

Simply order Part # CL9DPC or CL10DPC

At Challenger, We listen to what the “Customer Wants”


Shown:Model 40EFX (12,000 lbs. capacity)with optional 24006C ling jacks (6,000 lbs. lifting capacity each)

Challenger Lift’s 12,000 lbs. four-post liftsare a great way to increase your serviceoffering and revenue potential.

Our 40 Series have features that youwould expect to pay more for, like solidpiece column construction, automaticwheel o s, wheel curbs and anti-skidcoating on runways to minimize slipping, etc.

With optional ling jacks, bolt-on alignment kit, oil drain pan, etc., you’ll beable to accommodate just about anythingthat comes in for service.

Call us at 800-648-5438, our nationalnetwork of authorized distributors andinstallers will be glad to show you how toraise your service to full capacity.

We don’t just stand behind our products, we stand under them!TM

IDEAL FOR SERVICING:Tires & BrakesMufflersFront-EndsShocks & StrutsAlignmentTransmissionsFast LubesInspectionsand much more!

22063_Part1d.qxd 3/25/2004 7:57 AM Page 1

st p

lor

lro

* Optional 3 phase electrical also available. Standard lift colors are Red (as shown) and Blue.

Challenger Lifts, Inc. reserves the right to make changes without notice and without making changes retroactive.Unloading, installation and oil not included.

Attractive Lease Programs Available. GSA CONTRACT # GS-O7F-8950D • CAGE CODE 0KD44SIN#'s 253-23, 253-23A, 253-38 • DUNS# 79-435-3680

Lit# 40E 4/04©2004, Challenger Lifts, Inc.

CHALLENGER LIFTS, INC.200 Cabel StreetLouisville, Kentucky 40206Phone Toll-Free: 800-648-5438

502-625-0700Fax: 502-625-0711

E-mail: [email protected] Credit and Debit Cards Accepted

Technicians candisengage all fourcolumns at thesame time withour single-pointair actuated lockrelease.

Increase your services and revenue potential with a set ofjacks for wheel freeing capabilities (# 24006C). Ideal for brake, tire,alignment, suspension work and much more. Add our internal airlinekit (# 40230) and you can save valuable time by using both jacks without changing air supply.

Four-Post Surface Lifts -12,000 lbs. Capacity

Optional Accessories:

Power Unit Features:

For more information, contact your authorized Challenger Lift Distributor:The Automotive Lift Institute (ALI) certifiesthat the 40 Series 4-post lifts described hereincomply with the applicable provisions of theAmerican National Standards ANSI/ALI ALCTV-1998 and are Third Party Validated bythe ETL Testing Laboratory.

Convenient single push button power unit raises lift and a release valve handle lowers it.

Turn your lift into a workstation

with our column mounted

Air-Electric Service

Station.(# 10310)

Filter/lubricator/regulatorincluded

Rubber pad adapters protect a vehicle’s

delicate undercoating.

MODEL DESCRIPTION

24006C - Jack 6000 lbs. (2722 kg) lifting capacity with 40270 side members

40230 - Internal Airline Kit for operating dualair jacks

402003D - Bolt-on Alignment Conversion Kit includes front radius gages, rear slip plates and hardware

10267 - Oil Drain Pan Kit 32 gallon (132 liters) capacity

10266 - Drive-thru Ramp Kit for convenient drive-on/drive-off operation

10310 - 4-Post Lift Air-Electric Service Station with filter/lubricator/regulator

SPECIFICATIONS Model: 40NFX Model: 40SFX Model: 40EFX Model: 40XFXMaximum Wheelbase 1571/2" (4001mm) 1571/2" (4001mm) 1821/2" (4636mm) 210" (5334mm)

A. Rise 7 " ( 702 mm) " ( mm) " ( mm) " ( mm)

B. Length Overall 18' 3" (5563mm) 18' 3" (5563mm) 20' 4" (6198mm) 22' 8" (6909mm)

C. Width Overall 10' 1" (3073mm) 10' 11" (3327mm) 10' 11" (3327mm) 10' 11" (3327mm)

D. Inside of Columns 106" (2692mm) 116" (2946mm) 116" (2946mm) 116" (2946mm)

E. Between Columns 1701/2" (4331mm) 1701/2" (4331mm) 1951/2" (4966mm) 223" (5664mm)

F. Height of Columns " ( 99mm) " ( mm) " ( mm) " ( mm)

G. Width of Runways 20" (508mm) 20" (508mm) 20" (508mm) 20" (508mm)

H. Height of Runways 7" (178mm) 7" (178mm) 7" (178mm) 7" (178mm)

I. Width Between Runways (Minimum)

40" (1016mm) 40" (1016mm) 40" (1016mm) 40" (1016mm)

J. Width Between Runways (Maximum)

43" (1092mm) 43" (1092mm) 43" (1092mm) 43" (1092mm)

Lifting Capacity 12000 lbs. (5443kg)12000 lbs. (5443kg)12000 lbs. (5443kg) 12000 lbs. (5443kg)

Air Supply Required 85-115 psi 85-115 psi 85-115 psi 85-115 psiMotor 2HP 2HP 2HP 2HPVoltage (Single Phase Std.)* 208v - 230v 208v - 230v 208v - 230v 208v - 230vSpeed of Rise Seconds Seconds Seconds SecondsMin. Recommended 11' x 22' 12' x 22' 12' x 24' 12' x 24'Bay Size (3353mm x 6706mm) (3658mm x 6706mm) (3658mm x 7315mm) (3658mm x 7315mm)

33/8" Min.15 3/8" Max.

40" Min.43" Max.

33" Min.50" Max.

22063_Part1d.qxd 3/25/2004 7:58 AM Page 2


9 79 79 790 7020 7020 7020

901/2 901/2 901/2 901/222 9922 9922 9922

70 70 70 70

or lling

or lling

R linlo g

or lling

Looking for a complete Alignment Package?

Challenger Lifts’ New 12,000 lbs. “Open-Front”and “Closed-Front” Alignment Rack Packagesare a great way to increase your service offering and revenue potential.

With our AR40 Series, you'll easily be able tosupport “roll-back” compensation. Otherfeatures include flush mount stainless steelturning radius gauges and rear slip plates, aninternal air line system for your dual slidingjacks, multi-position work-steps, automaticwheel stops, etc.

With our alignment packages, you’ll be able toaccommodate just about anything that comesin for service. Call us at 800-648-5438, ournational network of authorized distributorsand installers will be glad to show you how toraise your service to full capacity.

We don’t just stand behind our products, westand under them!TM


INCLUDES:Recessed Radius GaugesRecessed Rear Slip PlatesDual Sliding Air Jacks Internal Air Line Systemand much more!

Shown: Model AR40EAO (12,000 lbs. capacity) with sliding jacks(6,000 lbs. lifting capacity each)

"Closed-Front"Alignment Packagesalso available!(See back for details)

Both our “Open-Front” and “Closed-Front” AlignmentPackages include dual 6,000 lbs. sliding jacks (24006C) thatutilize an internal air line system, flush mount 45o stainlesssteel radius gauges and a multi-position work-steps. Ourinternal airline kit saves you valuable time by using bothsliding jacks without changing air supply.

ALIGNMENT PACKAGE ACCESSORIES ARE ALSO AVAILABLE INDIVIDUALLY. Please contact factory for details.

Optional Accessory:

For more information, contact your authorized Challenger Lift Distributor:

Turn your lift into aworkstation with ourcolumn mounted Air-Electric Service Station(#10310).

Open-Front / Closed-Front Alignment Racks 12,000 lbs. Capacity

* Maximum wheelbase is based on a tire diameter of 30".** Optional 3 phase electrical also available. Standard lift color are Red (as shown) and Blue.

Also available in a “Open-Front” General Service 4-Post Lift configuration (Model # 40EFO and 40XFO).

Challenger Lifts, Inc. reserves the right to make changes without notice and without making changes retroactive.Unloading, installation and oil not included.


Lit# AR40 10/04©2004, Challenger Lifts, Inc.


502-625-0700Fax: 502-625-0711



When you get our Alignment System......You get the Complete Package!

Multi-Position Work Step

Filter, Lubricator, Regulator on each Sliding Jack

Air Operated Safety Lock System

Other Features:

SPECIFICATIONS AR40EAO AR40XAO AR40EAX AR40XAX

Maximum Wheelbase* 1821/2" 210" 1821/2" 210"(4636mm) (5334mm) (4636mm) (5334mm)

Max. 2 Wheel Alignment* 1661/2" 194" 1661/2" 194"(4229mm) (4927mm) (4229mm) (4927mm)

4 Wheel Alignment 88" - 158" 88" - 158"(2235mm - 4013mm) (2235mm - 4013mm)

A. Rise Height 79" 79" 79" 79"(2007mm) (2007mm) (2007mm) (2007mm)

B. Length Overall 20' 9" 23' 20' 4" 22' 8"(6325mm) (7010mm) (6198mm) (6909mm)

C. Width Overall 11' 10" 11' 10" 10' 11" 10' 11"(3607mm) (3607mm) (3327mm) (3327mm)

D. Inside of Columns 120" front - 116" rear 116"(3048mm) - (2946mm) (2946mm)

E. Between Columns 195" 2221/2" 195" 2221/2"(4953mm) (5652mm) (4953mm) (5652mm)

F. Height of Columns 991/2" front - 901/2" rear 901/2"(2527mm) - (2299mm) (2299mm)

G. Width of Runways 20" 20" 20" 20"(508mm) (508mm) (508mm) (508mm)

H. Height of Runways 7" 7" 7" 7"(178mm) (178mm) (178mm) (178mm)

I. Width Between Runways 43" 43" 40" - 43"(1092mm) (1092mm) (1016mm - 1092)

Lifting Capacity 12,000 lbs. 12,000 lbs. 12,000 lbs. 12,000 lbs.(5443 kg) (5443 kg) (5443 kg) (5443 kg)

Air Supply Required 85-115 psi 85-115 psi 85-115 psi 85-115 psi

Motor 2HP 2HP 2HP 2HPVoltage (Single Phase Std.)** 208v-230v 208v-230v 208v-230v 208v-230vSpeed of Rise 70 Sec. 70 Sec. 70 Sec. 70 Sec.

Min. Recommended Bay Size 12' x 24' 12' x 26' 12' x 24' 12' x 26'(3658x7315mm) (3658x7925mm) (3658x7315mm) (3658x7925mm)

OPEN-FRONT* CLOSED-FRONT

The Automotive Lift Institute (ALI) certifies that the AR40 Series Alignment Racks describedherein comply with the applicable provisions of the American National Standards ANSI/ALI ALCTV-1998 and are Third Party Validated by theETL Testing Laboratory.

Two 6,000 lbs Sliding Jacks Included:

Filter/lubricator/regulatorincluded

Rubber pad adapters protect a vehicle’s

delicate undercoating.

31/4" Min.12 7/16" Max.

04 " .niM34 " .xaM

33 " .niM05 " .xaM


Shown: Model 1500215,000 lbs. lifting capacity

Whether you want to expand your fleetservice capabilities, avoid downtime or justincrease your bottom line, Challenger Lift’s12,000, 15,000 and 18,000 lbs. 2-post lifts arethe solutions for your servicing needs.

Not only does our Heavy-Duty Series lift alot, it’s a lot of lift. With features that youwould expect to pay more for, like lowprofile arms, padded overhead cut-off bar,adapter accessories, etc. In fact, no otherlift company gives you more.



Challenger Lifts, Inc. reserves the right to make changes to specifications without notice and without making changes retroactive.Unloading, installation and oil not included.


Lit# HD2POST 5/03©2003, Challenger Lifts, Inc.


502-625-0700Fax: 502-625-0711


SPECIFICATIONS 12000 12001 12002 15000 15002 18000 18002A. Rise Height* 843/4" 843/4" 843/4" 851/2" 851/2" 851/2" 851/2"

(2153mm) (2153mm) (2153mm) (2172mm) (2172mm) (2172mm) (2172mm)

B. Height Overall 13' 8" 14' 8" 15' 8" 14' 6" 16' 6" 14' 6" 16' 6"(4166mm) (4470mm) (4775mm) (4420mm) (5030mm) (4420mm) (5030mm)

C. Width Overall 11' 10" 11' 10" 11' 10" 12' 103/4" 12' 103/4" 12' 103/4" 12' 103/4"(3607mm) (3607mm) (3607mm) (3931mm) (3931mm) (3931mm) (3931mm)

D. Drive-Thru Clearance 1041/2" 1041/2" 1041/2" 1063/4" 1063/4" 1063/4" 1063/4"(2654mm) (2654mm) (2654mm) (2712mm) (2712mm) (2712mm) (2712mm)

E. Floor To Overhead Switch 13' 1" 14' 1" 15' 1" 13' 11" 15' 11" 13' 11" 15' 11"(3988mm) (4293mm) (4597mm) (4242mm) (4852mm) (4242mm) (4852mm)

F. Arm Reach (Min.) 37" 37" 37" 381/2" 381/2" 381/2" 381/2"(940mm) (940mm) (940mm) (978mm) (978mm) (978mm) (978mm)

G. Arm Reach (Max.) 54" 54" 54" 62" 62" 62" 62"(1372mm) (1372mm) (1372mm) (1575mm) (1575mm) (1575mm) (1575mm)

H. Adapter Height Screw Pad Adj. 5" - 63/4" Screw Pad Adj.61/4" - 81/2"(127mm - 171mm) (159mm - 216mm)

I. Adapter Height (w/Med. Ext.)** Screw Pad Adj. 8" - 93/4" Screw Pad Adj.101/4" - 121/2"(203mm - 248mm) (261mm - 318mm)

J. Adapter Height (w/High Ext.)** Screw Pad Adj. 11" - 123/4" Screw Pad Adj.141/4" - 161/2"(279mm - 324mm) (362mm - 420mm)

K. Inside Columns 1141/2" 1141/2" 1141/2" 120" 120" 120" 120"(2908mm) (2908mm) (2908mm) (3048mm) (3048mm) (3048mm) (3048mm)

Lifting Capacity 12,000 lbs. 12,000 lbs. 12,000 lbs. 15,000 lbs. 15,000 lbs. 18,000 lbs. 18,000 lbs.(5443 kg) (5443 kg) (5443 kg) (6804 kg) (6804 kg) (8165 kg) (8165 kg)

Air Supply Required 85-115 psi 85-115 psi 85-115 psi 85-115 psi 85-115 psi 85-115 psi 85-115 psi

Motor 2HP 2HP 2HP 2HP 2HP 2HP 2HPVoltage (Single Phase Std.)*** 208v-230v 208v-230v 208v-230v 208v-230v 208v-230v 208v-230v 208v-230vSpeed of Rise 60 Sec. 60 Sec. 60 Sec. 80 Sec. 80 Sec. 80 Sec. 80 Sec.

Ceiling Height Required 13' 9" 14' 9" 15' 9" 14' 7" 16' 7" 14' 7" 16' 7"(4191mm) (4496mm) (4801mm) (4445mm) (5055mm) (4445mm) (5055mm)

Maximum Load Per Arm 3,000 lbs. 3,000 lbs. 3,000 lbs. 3,750 lbs. 3,750 lbs. 4,500 lbs. 4,500 lbs.(1360 kg) (1360 kg) (1360 kg) (1700 kg) (1700 kg) (2041 kg) (2041 kg)

* Rise height is measured with screw pads in high position.** Medium and high auxiliary adapter extension are standard.

*** Optional 3 phase electrical also available. Standard lift colors are Red and Blue.

Technicians can disengage both columns at the same time with our

single-point air actuated lock release

MediumExtension

To accommodate a wide variety of vehicles, screw-up truckadapters and extensions are standard equipment. Standardequipment includes: four screw-up adapters, four mediumextensions and two high extensions. Screw-up adapters andextensions are conveniently located on column mountedadapter organizer.

Heavy-Duty 2-Post Surface Lifts Capacity

Standard Adapter Accessories:

Features:


The Automotive Lift Institute (ALI) certifies that the Heavy-Duty 2-Post Lifts (12000, 15000,and 18000 Series) described herein complywith the applicable provisions of the AmericanNational Standards ANSI/ALI ALCTV-1998 andare Third Party Validated by the ETL TestingLaboratory.

Convenient single push button power unit raises lift and a release valve handle lowers it.

User friendly arm restraints automaticallydisengage when lift is fully lowered for easypositioning of arms and securely engagewhen lift is raised.

Turn your lift into a workstation with our OPTIONAL Air-

Electric Service Station. (# 10264)

Single piece adapter organizerprevents adapters from being misplaced .

.

HighExtensionScrew

Adapter

Model Number 44025 44025-AR 44025E 44025E-AR 44025X 44025X-AR 44030 44030-AR 44030E 44030E-AR 44030X 44030X-AR

Lift Capacity 25,000 lbs 25,000 lbs 25,000 lbs 30,000 lbs. 30,000 lbs. 30,000 lbs.

Maximum Wheelbase 230˝ 290˝ 350˝ 230˝ 290˝ 350˝

Max. 2 Wheel Alignment N/A 220˝ N/A 280˝ N/A 340˝ N/A 220˝ N/A 280˝ N/A 340˝

Rise 68˝ 68˝ 68˝ 68˝ 68˝ 68˝

Overall Length 24´ 7½˝ 29´ 7½˝ 34´ 7½˝ 24´ 7½˝ 29´ 7½˝ 34´ 7½˝

Overall Width 12´ 5½˝ 12´ 5½˝ 12´ 5½˝ 12´ 5½˝ 12´ 5½˝ 12´ 5½˝

Overall Height 92˝ 92˝ 92˝ 92˝ 92˝ 92˝

Inside of Columns 132½˝ 132½˝ 132½˝ 132½˝ 132½˝ 132½˝

Between Columns 233¾˝ 293¾˝ 353¾˝ 233¾˝ 293¾˝ 353¾˝

Width of Runways 24˝ 24˝ 24˝ 24˝ 24˝ 24˝

Height of Runways 9˝ 9˝ 9˝ 9˝ 9˝ 9˝

Width Between Runways 54˝ - 75˝ 54˝ - 75˝ 54˝ - 75˝ 54˝ - 75˝ 54˝ - 75˝ 54˝ - 75˝

Motor 2HP 2HP 2HP 2HP 2HP 2HP

Voltage - Single Phase 208-230v 208-230v 208-230v 208-230v 208-230v 208-230v

Speed of Rise 105 sec. 105 sec. 105 sec. 105 sec. 105 sec. 105 sec.

Amps 30 30 30 30 30 30

Model#: 44025

44025series - 44030seriesHeavy Duty 4 -Post Surface Mounted Lifts

Challenger Lifts, Inc. reserves the right to make changes without notice and without making changes retroactive. Unloading, installation and oil not included. www.challengerlifts.com

Challenger Lifts, Inc.200 Cabel StreetLouisville, KY 40206

Lit# 44025-30-6/05©2005, Challenger Lifts, Inc.

toll free: 800.648.5438phone: 502.625.0700fax: 502.625.0711

Features:

• Superior lifting system features tensile lift chain and sealed roller bearings for maximum reliability

• Heavy-duty cylinder provides optimum lifting with minimum maintenance

• Single point air actuated lock release

• Internal track to accommodate rolling jacks or oil pan

• Alignment models feature turning radius gauge cut outs for flush mounted 10500HD gauges

Part # DescriptionSAJ9S 9,000 lbs. rolling jack, adj. width 36˝-52˝SAJ12 12,000 lbs. rolling jack, adj. width 36˝-52˝SAJ15 15,000 lbs. rolling jack adj. width 36˝- 52˝

10267 Oil drain pan kit, adjustable width, 32 gallon

10500HD Heavy duty powder coated turning radius gauges

44RK25 Ramp kit, pivoting, 36˝ long for drive thru operation

44RKE25 Ramp kit, pivoting, 72˝ long for drive thru operation


email: [email protected]

Model#: 44018

44018seriesHeavy Duty 4 Post Surface Mounted Lifts

Features:

• Superior lifting system features oversized lift chain and sealed roller bearings for maximum reliability

• Mechanically operated lock is continuously engaged

• Heavy-duty cylinder provides optimum lifting with minimum maintenance

• Internal track to accommodate rolling jacks or oil pan

• Alignment models feature double radius gauge cut outs, dual rear slip plates, internal airline kit, and single point air actuated lock release with 17 level working alignment heights

Model Number 44018 44018E 44018-AR 44018X-AR

Lift Capacity 18,000 lbs. 18,000 lbs. 18,000 lbs. 18,000 lbs.

Maximum Wheelbase 194˝ 230˝ 236˝ 272˝

Min. - Max. - 4 Wheel Align N/A 98˝ - 206˝

Max. 2 Wheel Align N/A 220˝ 256˝

Rise 78¾˝ 833/8˝

Overall Length 21´ 4˝ 24´ 4˝ 25´ 11½˝ 28´ 11½˝

Overall Width 11´ 61/8˝ 11´ 9½˝

Overall Height 8´ 6½˝

Inside of Columns 121˝ 122˝

Between Columns 204˝ 240˝ 204˝ 240˝

Width of Runways 22˝

Height of Runways 7¼˝ 117/8˝

Width Between Runways 36˝ - 54˝

Motor 2HP

Voltage - Single Phase 208 - 230v

Speed of Rise 60 sec.

Amps 30

Challenger Lifts, Inc. reserves the right to make changes without notice and without making changes retroactive. Unloading, installation and oil not included.



toll free: 800.648.5438phone: 502.625.0700fax: 502.625.0711email: [email protected]

Lit# 44018-6/05©2005, Challenger Lifts, Inc.

Part#: SAJ-9

• 9,000 lbs. lifting capacity

• Extended lift height 11˝

• Adjustable width 36˝- 52˝

• SAJ-9A for alignment racks

Part#: 10267

Part # Description Air Hydraulic rolling jackSAJ9S adjustable width 36̋ - 52̋ for 44018 and 44018E

Air Hydraulic rolling jackSAJ9A adjustable width 36̋ - 52̋ for 44018AR and 44018X-AR10500 Powder coat turning radius gauges10500SS Stainless Steel turning radius gauges44RK18 Ramp kit, pivoting, 39̋ long44RKE18 Ramp kit, pivoting, 52̋ long for AR’s

10267 Oil drain pan kit,

adjustable width, 32 gallon


• 32 gallon rolling oil drain pan

• Baffl ed for splash reduction

• 1¼˝ gate valve standard with 5´ evacuation hose

44040series - 44060seriesHeavy Duty 4-Post Surface Mounted Lifts

Features:

• Single point, air actuated lock release system

• Velocity fused redundant hydraulic safety system

• Superior lifting system features tensile leaf chain and sealed roller bearings for maximum reliability

• Dual cylinders provide stability while raising uneven loads

• Independent control console Model#: 44060

Model Number 44040 44040E 44040X 44050 44050E 44050X 44060 44060E 44060X

Lift Capacity 40,000 lbs 40,000 lbs 40,000 lbs 50,000 lbs 50,000 lbs 50,000 lbs. 60,000 lbs. 60,000 lbs. 60,000 lbs.

Maximum Wheelbase 310˝ 370˝ 430˝ 310˝ 370˝ 430˝ 310˝ 370˝ 430˝

Min. - Max. - 4 Wheel Align N/A N/A N/A

Max. 2 Wheel Align N/A N/A N/A

Rise 73˝ 73˝ 73˝

Overall Length 36´ 41´ 46´ 36´ 41´ 46´ 36´ 41´ 46´

Overall Width 17´ 1¼˝ 17´ 1¼˝ 17´ 1¼˝

Overall Height 92˝ 92˝ 92˝

Inside of Columns 144˝ 144˝ 144˝

Between Columns 290˝ 350˝ 410˝ 290˝ 350˝ 410˝ 290˝ 350˝ 410˝

Width of Runways 32˝ 32˝ 32˝

Height of Runways 14˝ 14˝ 14˝

Width Between Runways 36˝- 58˝ 36˝- 58˝ 36˝- 58˝

Motor 10HP 15HP 15HP

Voltage -3 Phase 230-460v 230-460v 230-4600v

Speed of Rise 70 sec. 75 sec. 75 sec.

Amps 30 30 30

Challenger Lifts, Inc. reserves the right to make changes without notice and without making changes retroactive. Unloading, installation and oil not included.




Lit# 44040-60-6/05©2005, Challenger Lifts, Inc.

Part # Description

SAJ15 15,000 lbs. air hydraulic rolling jack

adj. width 36˝- 52̋


adj. width 36̋ - 52̋


adj. width 36̋ - 52̋

44RK40 Ramp kit, fixed

96´ long for drive thru operation10267 Oil drain pan kit, adj. width, 32 gallon

10500HD Heavy duty powder coated

turning radius gauges



Shown:Model CS122012,000 lbs. lifting capacity

“Introducing the newest members of our EnviroLiftTM Family!”

Challenger Lift’s New Heavy-Duty Cassette-Style Electric Inground Lifts are a great way to add or expand your fleet service capabilities and increase your bottom line.With lifting capacities of 12,000 and15,000 lbs., they are the solutions foralmost any servicing need.

Unlike traditional inground lifts, all of our EnviroLiftTM products are contained in a sealed container to protect yourinvestment and the environment. They are ideal for maximizing valuable bay spaceand are relocatable and leasable.

Call us at 800-648-5438! Our nationalnetwork of authorized distributors andinstallers will be glad to show you how toraise your service to full capacity.


“IT’S THE BEST OF SURFACE AND INGROUND

LIFTS COMBINED!”

12,000 & 15,000 lbs. Capacity!


502-625-0700Fax: 502-625-0711

E-mail: [email protected]


EnviroLift Cassette Lifts -12,000/15,000 lbs. Capacity



Lit# CS1220 12/02©2002, Challenger Lifts, Inc.

For more information, contact your authorizedChallenger Lift Distributor:

Major Credit and Debit Cards Accepted

TM

Features & Benefits:• Maximize the number of bays in your shop and

generate more revenue potential (requires less shop space than surface mounted lifts).

• Eliminate the risk of vehicle door damage (no columns or overhead obstructions).

• Low-profile arms and superstructure for easy drive-over clearance.

• Unlike traditional inground lifts, the EnviroLifts are removable, relocatable and leasable.

• Convenient 3" incremental air actuated lock system to raise vehicle at technician’sergonomic working height to minimize fatigue and increase productivity.

MODEL DESCRIPTION

CSPK - Universal Pre-Kit for all EnviroLift Models (CS0920, CS1220 and CS1520 Series)

CS1220CK - Completion Kit for 12,000 lbs. EnviroLift

CS1520CK - Completion Kit for 15,000 lbs. EnviroLift

Optional Adapter Accessories:To accommodate a wider variety ofvehicles, our optional slip-on luxurycar adapters give you the flexibility tosafely raise just about any vehicle thatcomes in for service. (For use withCS1220 EnviroLift only)

Slip-On Luxury Car Adapters (# 10300)

8 1/2" Piston Diameter

Container Assembly (L x W x H)72 11/16" x 217/16" x 102 1/2"

CS1520 Plan View (above)15,000lbs. Lifting Capacity

CS1220 Plan View (below)12,000lbs. Lifting Capacity

1 1/2”

* Rise height is measured with superstructure in highest position.** Medium and high auxiliary adapter extensions are standard.

*** Optional 3 phase electrical also available, please specify at time of order.

MediumExtension

To accommodate a wide variety of vehicles, adjustablescrew-type truck adapters and extensions are standardequipment. Standard equipment includes: four adjustablescrew-type adapters, four medium extensions and fourhigh extensions.

Standard Adapter Accessories:

HighExtensionScrew

Adapter

SPECIFICATIONS Model: CS1220 Model: CS1520A. Rise Height* 811/4" (2064mm) 843/4" (2153mm)

Stroke 68" (1727mm) 68" (1727mm)

B. Width Overall 99" (2515mm) 711/2" (1816mm)

C. Drive-Thru Clearance 88" (2235mm) NAD. Reach (Arm Min.) 32" (813mm) 261/4" (667mm)

E. Reach (Arm Max.) 491/4" (1251mm) 43" (1092mm)

F. Adj. Adapter Height** 5"- 71/4" 61/2"- 83/4"(127 - 184mm) (165 - 222mm)

G. Adj. Adapter Height** 8"- 101/4" 101/2"- 123/4"(w/Medium Extensions) (203 - 260mm) (267 - 324mm)

H. Adj. Adapter Height** 11"- 131/4" 141/2"- 163/4"(w/High Extensions) (279 - 337mm) (368 - 425mm)

Lifting Capacity 12,000 lbs. (5445kg) 15,000 lbs. (6806kg)

Capacity (Per Arm) 3,000 lbs. (1361kg) 3,750 lbs. (1701kg)

Motor 2HP 2HPVoltage (1 Phase Std.)*** 208v-230v 208v-230vSpeed of Rise 65 Seconds 80 SecondsAir Required 75 - 125 psi 75 - 125 psiRecommended Ceiling 82" plus height 85" plus heightHeight of tallest vehicle of tallest vehicle

The Automotive Lift Institute (ALI) certifies that the CS1220 and CS1520 described hereincomply with the applicable provisions of theAmerican National Standards ANSI/ALI ALCTV-1998 and are Third Party Validated by the ETLTesting Laboratory.


Shown: Model CS1020W10,000 lbs. lifting capacity

“Eliminate environmental concerns associated with traditional inground lifts!”

Challenger Lifts’ New EnviroLiftTM

Cassette-Style Electric Inground Lifts are fully contained in a sealed container to protect your investment and the environment.

Maximize the bays in your shop to increase your revenue potential with our leasable and relocatable EnviroLiftTM.

Call us at 800-648-5438! Our national network of authorized distributors and installers will be glad to show you how to raise your service to full capacity.


TM

Uses only 12 qts of hydraulic fluid

CHALLENGER LIFTS, INC.200 Cabel StreetLouisville, Kentucky 40206 Phone Toll-Free: 800-648-5438 502-625-0700 Fax: 502-625-0711 E-mail: [email protected]


EnviroLift Cassette Lifts - 10,000 lbs. Capacity

Challenger Lifts, Inc. reserves the right to make changes to specifications without notice and without making changes retroactive. Unloading, installation and oil not included.


Lit# CS1020W 07/05©2005, Challenger Lifts, Inc.


The Automotive Lift Institute (ALI) certifies that the CS1020W Series described hereincomply with the applicable provisions of the American National Standards ANSI/ALI ALCTV1998 and are Third Party Validated by the ETL Testing Laboratory.

Major Credit and Debit Cards Accepted

TM

Features & Benefits: Maximize the number of bays in your shop and generate more revenue potential (requires less shop space than surface mounted lifts).

Eliminate the risk of vehicle door damage (no columns or overhead obstructions).

Widest drive-thru in the industry.

Low stress structural design for longer life and better reliability.

EnviroLifts are removable and relocatable.

Convenient 3" incremental air actuated lock system to raise vehicle at technician’s ergonomic working height to minimize fatigue and increase productivity.

MODEL DESCRIPTION

CSPK - Universal Pre-Kit for all EnviroLift Models (CS1020W, CS1220 and CS1520 Series) CS1020WCK - Completion Kit for EnviroLift CS1020LS - EnviroLift Less Superstructure - for alignment purposes CS1020WSSA - Asymmetric Superstructure Only - 3-position “flip-up” CS1020WSSAR - Asymmetric Superstructure Only - “screw-type” rubber pad CS1020WSSFP - Symmetric Superstructure Only - 3-position “flip-up” CS1020WSSRP - Symmetric Superstructure Only - “screw-type” rubber pad CS1020WSSE - European Superstructure Only - 3-position “flip-up”CS1020WSSER - European Superstructure Only - “screw-type” rubber pad

* Standard models include a 3-position “flip-up” superstructure. “Screw-type” rubber pad superstructure models also available at NO EXTRA COST, please specify superstructure preference at time of order (see below). ** Rise height is measured with “flip-up” superstructure in highest position. *** Optional 3 phase electrical also available, please specify at time of order.

Adj. Screw Type:Reach ranging between highest and lowest screw positions

3 Position Flip-Ups:Three height positions:low, medium, and high.

Optional Adapter Accessories:

Slip-On Luxury Car Adapter Pair (# 10300)

SPECIFICATIONS Model: CS1020W* A. Rise Height** 78˝ (1981mm)

B. Width Overall 97˝ (2464mm)

C.Drive-Thru Clearance 87̋ (2210mm)

D. Reach (Long Arm Min.) 261/2˝ (673mm)

E. Reach (Long Arm Max.) 39˝ (991mm)

F. Reach (Asym. Arm Min.) 24 3/8˝ (619mm)

G. Reach (Asym. Arm Max.) 35 13/16˝ (910mm)

H. Min. Adapter Height 4˝ (102mm)

I. Low Step Height 61/2˝ (165mm)

J. High Step Height 10 ˝ (254mm)

Lifting Capacity 10,000 lbs. (4535kg)

Capacity (Per Arm) 2,500 lbs. (1134kg)

Motor 2HP Voltage (Single Phase Std.)*** 208v-230v Speed of Rise 48 Seconds Air Required 75 - 125 psi Min. Recommended 10´ x 20´ Bay Size (3048mm x 6096mm)

Recommended 79˝ plus height Ceiling Height of tallest vehicle

5˝ Flip-Up Truck Adapter Kit Pair(# 16621)

6˝ Screw type Truck Adapter Pair (# 10303)

Arm Design Configurations:

10˝ Screw type Truck Adapter Pair (# 10304)


Shown: Model 66000 6,000 lbs. lifting capacity

Challenger Lift’s Portable Mid-Rise Liftsare a great way to increase the productivityin your shop. It’s like having a service bayanywhere you want...indoors or out!

Our 66000 Series Mid-Rise Lifts are availablewith either an electric or pneumatic motor to accommodate specialized service environments, like body shops. Motor isconveniently mounted to a heavy-duty towdolly, making it easy to move and operate on almost any solid surface.

Features include a sliding/rotating armdesign with rubber pads, low drive-overclearance, and much more.



IDEAL FOR SERVICING:Tires & BrakesDetailingBody RepairInspectionsCustomizingEstimatingRefinishingand much more!

It’s like having a

lift in any bay!

Standard lift colors are Red (as shown) and Blue.



Lit# 66000 9/02©2002, Challenger Lifts, Inc.


502-625-0700Fax: 502-625-0711



Portable Mid-Rise Lifts -6,000 lbs. Capacity

Optional Accessories:


Convenient single push button powerunit raises lift and a releasevalve handle lowers it.

66100 - Includesfour (4) Adjustable“Screw-Type”Adapters for higherframe vehicles.Adapters incorporaterubber pads to protecta vehicle’s delicateundercoating.

Four (4) “Frame-Engaging” AdapterCovers also included.

SPECIFICATIONS Model: 66000 Model: 66000AA. Rise 48" (1219mm) 48" (1219mm)

B. Length Overall 7' 6" (2286mm) 7' 6" (2286mm)

C. Width Overall 3' 33/8" (1000mm) 3' 33/8" (1000mm)

D. Min. Collapsed Height 33/8" (98mm) 33/8" (98mm)

E. Pad Height (Minimum) 51/2" (140mm) 51/2" (140mm)

F. Pad Height (Maximum) 491/2" (1257mm) 491/2" (1257mm)

Lifting Capacity 6,000 lbs. (2722kg) 6,000 lbs. (2722kg)

Hydraulic Hose 12' (3658mm) 12' (3658mm)

Safety Lock Positions 4 4Electric Motor 1 HP naVoltage (Single Phase) 115v naPneumatic Motor na 2 HPAir Supply Required na 100 psiSpeed of Rise 45 Seconds 65 SecondsMin. Recommended 10' x 22' 10' x 22'Bay Size (3048mm x 6706mm) (3048mm x 6706mm)

43/4" to7"

Challenger Lifts is a member of theAutomotive Lift Institute (ALI). This symbolrepresents over 50 years of dedication to liftsafety by providing rigorous safety standardsand training.

21/4"

Frame-EngagingAdapter CoverAll Portable Mid-Rise

Lifts come with four(4) Rubber Pad Adapters and “Height Extension”.

Portable Mid-Rise Lift comes with either electric or pneumatic powerunit conveniently mounted to heavy-duty tow dolly for easy movement around the shop (see front cover).

Other Features:

Power Unit Features:

Slip-On Adapter Kit Included:

Model#: 50050stand position

Challenger Lifts’ original tailgate support stand is designed to support the tailgate of sanitation trucks while conducting preventative maintenance and repairs to the hydraulic systems.

Features:

• 12,000 lbs. capacity per stand

• 30˝ triangular base

• Stabilizing brake to ensure accurate and safe placement

• 5 position secondary load holding pin

• Infi nitely adjustable height from 7´ - 10´

• Universal round head

• New 5½˝ round contact pad adapter with replaceable rubber insert swivels 360˚

• 2½˝ diameter Square thread double lead screw give 1˝ height adjustment for each revolution of the nut

• 4 rubber 6˝ wheels with greaseable roller bearings ( 2 fixed and 2 swivel casters)

• Stand may be moved like a dolly, using the 2 fixed wheels for short distances or position the double swivel wheeled “drop-leg” to move the like a cart for longer distances




Challenger Lifts, Inc. reserves the right to make changes without notice and without making changes retroactive. Unloading, installation not included.

Lit# 50050-6/05©2005, Challenger Lifts, Inc.

Model#: 50050cart position

also available:

model#: 5002417,000 lbs. capacityadj. 36˝-56˝

model#: 5001817,000 lbs. capacityadj. 60˝-80˝

Retrofittable brake for 50040 (part #: 50040-60)

Universal round head(part #: 50040-50)

Portable Tailgate

Support Stand

Versymmetric 2-Pos tLifts

Documents

Transcript of Versymmetric 2-Pos tLifts