Versus Gas USA System Promotional · PDF fileVersus Gas USA System Promotional Catalog ... 5a...
Transcript of Versus Gas USA System Promotional · PDF fileVersus Gas USA System Promotional Catalog ... 5a...
Versus Gas CNG ECU
Processor: DSP with efficiency up to 70MIPS
Housing: Aluminum
Dimensions: 13.8 x 13.35 x 3.8 cm
Connector: 2x24 PIN
Safety: original Leak Detection System "LDS"
Calibration: Self-Calibration System "SCS" supporting automatic correction adjustments
OBD Communication available
Integrated short circuit protection system
The self-diagnosis and troubleshooting system
Supports engines up to 8 cylinders depending on the type of controller
"V" Controllers
“V” group of controllers contain the most advanced technology, starting from the selection of proven,
high-performance components through production technology, quality control and use of unique system
solutions.
All “V” controllers are equipped with a powerful microprocessor which supports the built-in automatic
correction and calibration system. This automatic calibration system is very user friendly allowing the
installer to easily tune the vehicles CNG system at the push of a button.
Key features that are integrated into each “V” version controller: Leakage Detection System (LDS) and
Self-Calibration System (SCS).
"VOBD" Controllers
"VOBD" controllers use is recommended in cars equipped with the most modern engines equipped with
electronic components that are sensitive to interference factory parameters that require continuous
monitoring of engine parameters and composition of the mixture. Precisely selected injection time,
depending on the gasoline computer display makes the controller "VOBD" one of the best and most
versatile controllers existing on the market.
CNG Regulator (VR-C Standard):
Type of GAS: CNG
Body: Aluminum die cast
Gas Working Pressure: 23.2 psi (1,6 bar)
Maximum Power: 241 HP (180 KW)
Working Temperature Range (°C): -30 /+120
Gas Outlet External Diameter: 12 mm or 14 mm
Engine Cooling liquid Outlet/Inlet: 10 mm or 16 mm
Low Pressure Shut-off Valve: integrated
Solenoid Valve Nominal Voltage: +12V
Overall dimension: 15/16.5/14.5 cm
Body Diameter: 10 cm
Weight: 3.75 lbs
Approvals: ECE110R00, ISO 1550099
VR-C is a pressure regulator designed by FHT and dedicated to CNG Sequential Gas Injection
Systems.
It can be installed in most types of cars. The reducer is supplied with sensitive 1st stage reduction
system that warrants stable pressure value in spite of pressure variation coming from the tank.
Thanks to its highly efficient two stage Gas flow control system it ensures the most optimal CNG
dosage in any drive conditions.
CNG/ LPG Injectors FH02:
Body: aluminum
Fuel: CNG/LPG
Voltage: 12V
Working Pressure: 7.25-36.25 psi (0.5-2.5 bar)
Maximum working pressure: 65.5 psi (4.5 bar) Opening/closing time: 3.0 msec/2.5 msec
Resistance of the coil: 3 Ohm ±4%, other upon request
T. range (°C): -30 /+120
GAS Inlet (external): 12 mm, other upon request
Standard Valve seat diameter: 4 mm
Calibration nozzle sizes available: 1.5 – 3.5 mm (0,25 mm step)
Body composition available: 2-cyl, 3-cyl, 4-cyl
Normally: closed
Approvals: ECE 67R01, ECE110R00
The most popular solution for most engines with easy access to the inlet manifold. The FH02
injectors are some of the most advanced, durable injectors on the market. These injectors have
long life expectancies while also being fully serviceable. The FH02 injectors have a noise
reduction feature that will illuminate a lot of injector noise.
CNG/LPG Injectors
FH02-1:
Body: brass
Fuel: CNG/LPG
Voltage: 12V
Working Pressure: 7.25-36.25 psi (0.5-2.5 bar)
Maximum working pressure: 65.5 psi (4.5 bar)
Opening/closing time: 3.0 msec/2.5 msec
Resistance of the coil: 3 Ohm ±4%, other upon request
T. range (°C): -30 /+120
GAS Inlet (external): 12 mm, other upon request
Standard Valve seat diameter: 4 mm
Calibration nozzle sizes available: 1,5 - 3,5 mm (0,25 mm step)
Normally: closed
Approvals: ECE 67R01, ECE110R00
These injectors can be installed very close to the inlet manifold nozzles when final length of
CNG hose installed between inlet manifold nozzles and calibration nozzles can be short enough.
These injectors are ideal for vehicles in which Injector FH02-4cyl cannot be installed correctly or
there is no space to install Injector FH02-4. These allow for an easier installation.
Injector Adapters
These injector inserts allow the installation time to be reduced
dramatically. The installer simply raises the injector rail and slips these
inserts into place. NO MORE DRILLING THE MANIFOLD! This is a new
age of CNG system installation and these allow for the cleanest,
quickest, best quality installation. The items are available by request.
3 Different Styles available to fit your needs!
Plug & Play
The Versus Gas System has a variety of
plug and play components that come standard with all kits to ensure the ease of the
installation. Although there is still wire spicing that will occur during installation, these plug and
play components will help cut down on installation time.
CNG Injector
Wire Harness
CNG Pressure Gauge
MAP Sensor Water Temp Sensor
Plug & Play Injector Wiring
NO MORE SPLICING OEM INJECTOR WIRES! Now you do not need to
waste time and effort splicing injector wires but instead get the Plug &
Play injector harness. This harness will come with a male and female
end on your CNG wiring harness that will match your OEM injector
harness. You will simply unplug your OEM injector harness; plug it into
the male connector on the CNG harness, then plug the female connector
from the CNG harness into your OEM injector. These are available by
request.
Regardless of your vehicle we have the correct solution
CNG 8-Cyl. Conversion System (over 250 HP) with FH02-1 Injectors
Number Name
1a ECU V8 8-cyl
1b Harness P8 CNG 8-cyl
1c MAP-Sensor XFP1
1d Reducers Temp Sensor
1e Gas Temp Sensor “T”
1f Fuse Case
1g Fuse 10A
1h Change-over Switch
1i Horn (Buzzer)
1J Female Electrical Connector
1k Electrical Connector
1l Electrical Connector box
1m T-fitting for vacuum
2a Reducer VR-C (x2)
2b VR-C Inlet connection set
3a Injector FH02-1 (x8)
3b Inlet manifold nozzle (x10)
3c Anti-vibration dumper FH02 (x4)
3d Injector Calibration nozzle (x8)
4a Filter 1-4 (x2)
4b Gas Y Fitting
5a Manometer VR-C01 set
6a Water Hose (6.5 FT)
6b CNG Hose (8.2 FT)
6c CNG Hose (10.5 FT)
6d Vacuum hose (5 FT)
6e Water T-fitting (x2)
6f Metal Clamps (x14)
6g Metal Clamps (4)
6h Pressure Hose clamps (x18)
6i Vacuum Clamps (x6)
6j Tubing Support(x10)
Description
Kit is for 8 cylinder vehicles over 250 horse power
Kit includes everything for a complete under hood installation (shown in picture)
Catalogue Code: 8C4/32/9/24/2/79Z
Number Name
1a ECU V8 8-cyl
1b Harness P8 CNG 8-cyl
1c MAP-Sensor XFP1
1d Reducers Temp Sensor
1e Gas Temp Sensor “T”
1f Fuse Case
1g Fuse 10A
1h Change-over Switch
1i Horn (Buzzer)
1J Female Electrical Connector
1k Electrical Connector
1l Electrical Connector box
1m T-fitting for vacuum
2a Reducer VR-C (x2)
2b VR-C Inlet connection set
3a Injector FH02-2 (x4)
3b Inlet manifold nozzle (x10)
3c Anti-vibration dumper FH02 (x4)
3d Injector Calibration nozzle (x8)
4a Filter 1-1 (x2)
4b Gas Y Fitting
5a Manometer VR-C01 set
6a Water Hose (6.5 FT)
6b CNG Hose (8.2 FT)
6c CNG Hose (10.5 FT)
6d Vacuum hose (5 FT)
6e Water T-fitting (x2)
6f Metal Clamps (x14)
6g Metal Clamps (4)
6h Pressure Hose clamps (x18)
6i Vacuum Clamps (x6)
6j Tubing Support(x10)
Description
Kit is for 8 cylinder vehicles over 250 horse power
Kit includes everything for a complete under hood installation (shown in picture)
Catalogue Code: 8C5/32/7/21/2/79Y
CNG 8-Cyl. Conversion System (over 250 HP) with FH02-2 Injectors
CNG 8-Cyl. Conversion System (over 250 HP) with FH02-4 Injectors
Number Name
1a ECU V8 8-cyl
1b Harness P8 CNG 8-cyl
1c MAP-Sensor XFP1
1d Reducers Temp Sensor
1e Gas Temp Sensor “T”
1f Fuse Case
1g Fuse 10A
1h Change-over Switch
1i Horn (Buzzer)
1J Female Electrical Connector
1k Electrical Connector
1l Electrical Connector box
1m T-fitting for vacuum
2a Reducer VR-C (x2)
2b VR-C Inlet connection set
3a Injector FH02-4 (x2)
3b Inlet manifold nozzle (x10)
3c Anti-vibration dumper FH02 (x4)
3d Injector Calibration nozzle (x8)
4a Filter 1-1 (x2)
5a Manometer VR-C01 set
6a Water Hose (6.5 FT)
6b CNG Hose (8.2 FT)
6c CNG Hose (10.5 FT)
6d Vacuum hose (5 FT)
6e Water T-fitting (x2)
6f Metal Clamps (x14)
6g Metal Clamps (4)
6h Pressure Hose clamps (x18)
6i Vacuum Clamps (x6)
6j Tubing Support(x10)
Description
Kit is for 8 cylinder vehicles over 250 horse power
Kit includes everything for a complete under hood installation (shown in picture)
Catalogue Code: 8C4/32/5/21/2/79
CNG 8-Cylinder Conversion System (under 250 HP)
Number Name
1a ECU V8 8-cyl
1b Harness P8 CNG 8-cyl
1c MAP-Sensor XFP1
1d Reducers Temp Sensor
1e Gas Temp Sensor STD
1f Fuse Case
1g Fuse 10A
1h Change-over Switch
1i Horn (Buzzer)
1J Female Electrical Connector
1k Electrical Connector
1l Electrical Connector box
1m T-fitting for vacuum
2a Reducer VR-C
2b VR-C Inlet connection set
3a Injector FH02-4 (x2)
3b Inlet manifold nozzle (x10)
3c Anti-vibration dumper FH02 (x4)
3d Injector Calibration nozzle (x8)
4a Filter 1-1 (x2)
5a Manometer VR-C01 set
6a Water Hose (6.5 FT)
6b CNG Hose (6 FT)
6c CNG Hose (10.5 FT)
6d Vacuum hose (5 FT)
6e Water T-fitting (x2)
6f Metal Clamps (x14)
6g Metal Clamps (4)
6h Pressure Hose clamps (x18)
6i Vacuum Clamps (x6)
6j Tubing Support(x10)
Description
Kit is for 8 cylinder vehicles up to 250 horse power
Kit includes everything for a complete under hood installation (shown in picture)
Catalogue Code: 8C/3/5/11/2/78
Number Name
1a ECU V6 6-cyl
1b Harness P6 CNG 6-cyl
1c MAP-Sensor XFP1
1d Reducers Temp Sensor
1e Gas Temp Sensor “T”
1f Fuse Case
1g Fuse 10A
1h Change-over Switch
1i Horn (Buzzer)
1J Female Electrical Connector
1k Electrical Connector
1l Electrical Connector box
1m T-fitting for vacuum
2a Reducer VR-C
2b VR-C Inlet connection set
3a Injector FH02-1 (x6)
3b Inlet manifold nozzle (x7)
3c Anti-vibration dumper FH02 (x4)
3d Injector Calibration nozzle (x6)
4a Filter 1-3 (x2)
5a Manometer VR-C01 set
6a Water Hose (6.5 FT)
6b CNG Hose (5 FT)
6c CNG Hose (9 FT)
6d Vacuum hose (5 FT)
6e Water T-fitting (x2)
6f Metal Clamps (x14)
6g Metal Clamps (x4)
6h Pressure Hose clamps (x14)
6i Vacuum Clamps (x6)
6j Tubing Support(x10)
Description
Kit is for 6 cylinder vehicles up to 250 HP
Kit includes everything for a complete under hood installation (shown in picture)
CNG 6-Cylinder Conversion System with FH02-1 Injectors
Catalogue Code: 6C1/3/8/23/2/75U
CNG 6-Cylinder Conversion System
Number Name
1a ECU V6 6-cyl
1b Harness P6 CNG 6-cyl
1c MAP-Sensor XFP1
1d Reducers Temp Sensor
1e Gas Temp Sensor STD
1f Fuse Case
1g Fuse 10A
1h Change-over Switch
1i Horn (Buzzer)
1J Female Electrical Connector
1k Electrical Connector
1l Electrical Connector box
1m T-fitting for vacuum
2a Reducer VR-C
2b VR-C Inlet connection set
3a Injector FH02-3 (x2)
3b Inlet manifold nozzle (x7)
3c Anti-vibration dumper FH02 (x4)
3d Injector Calibration nozzle (x6)
4a Filter 1-1 (x2)
5a Manometer VR-C01 set
6a Water Hose (6.5 FT)
6b CNG Hose (5 FT)
6c CNG Hose (9 FT)
6d Vacuum hose (5 FT)
6e Water T-fitting (x2)
6f Metal Clamps (x14)
6g Metal Clamps (x4)
6h Pressure Hose clamps (x14)
6i Vacuum Clamps (x6)
6j Tubing Support(x10)
Description
Kit is for 6 cylinder vehicles up to 250 HP
Kit includes everything for a complete under hood installation (shown in picture)
Catalogue Code: 6C/3/4/11/2/77T
CNG 4-Cylinder Conversion System
Number Name
1a ECU V4 4-cyl
1b Harness P4 CNG 4-cyl
1c MAP-Sensor XFP1
1d Reducers Temp Sensor
1e Gas Temp Sensor “T”
1f Fuse Case
1g Fuse 10A
1h Change-over Switch
1i Horn (Buzzer)
1J Female Electrical Connector
1k Electrical Connector
1l Electrical Connector box
1m T-fitting for vacuum
2a Reducer VR-C
2b VR-C Inlet connection set
3a Injector FH02-1 (x4)
3b Inlet manifold nozzle (x5)
3c Anti-vibration dumper FH02 (x4)
3d Injector Calibration nozzle (x4)
4a Filter 1-4 (x1)
5a Manometer VR-C01 set
6a Water Hose (5.25 FT)
6b CNG Hose (5 FT)
6c CNG Hose (6 FT)
6d Vacuum hose (5 FT)
6e Water T-fitting (x2)
6f Metal Clamps (x8)
6g Metal Clamps (x4)
6h Pressure Hose clamps (x18)
6i Vacuum Clamps (x6)
6j Tubing Support(x10)
Description
Kit is for 4 cylinder vehicles up to 200 HP
Kit includes everything for a complete under hood installation (shown in picture)
This kit comes with optional injector patterns. FH02-4 (x1), FH02-2(x2), or FH02-1(x4) injector
patterns available for this kit.
Catalogue Code: 1C1/3/2/4/2/74O
Benefits of Purchasing
Purchase through Versus Gas USA or one of our authorized distributors to receive these
benefits!
Visit the technical support page of our website at www.versusgasusa.com to view:
Printable detailed installation manuals
Vacuum routing diagram
All wiring diagrams
common problems
Technical support link
Warranty part link
And much more all at your finger tips 24/7!
Versus Gas USA and has the ability to disperse warranty parts from our USA warehouse.
Versus Gas USA also has kits and parts in stock for quickest shipping. With every kit you will
receive FREE TECHNICAL SUPPORT to aid you in the installation process.
To find your VERSUS GAS USA authorized distributor please visit www.versusgasusa.com or
email [email protected].
[email protected] www.versusgasusa.com PHONE: 918-236-3983