Valve_Cast_Steel_Gate_Globe.pdf

AUSTRALIAN PIPELINE VALVE

Cast Steel ValvesGate, Globe, Check

Facsimile:

+61-(0)8-8285 0035

Email:

[email protected]

Website:

www.australianpipelinevalve.com.au

™®

© Australian Pipeline Valve 2011

This page is deliberately left blank.

ContentsFigure Number System

Material Combinations/FeaturesPhysical & Chemical Properties

General Design SpecificationsValve Selection Criteria

Bolted Bonnet Gate Valves OverviewBolted Bonnet Globe Valves OverviewBolted Bonnet Check Valves OverviewPressure Seal Bonnet Valves Overview

Gate Valve - Class 150Gate Valve - Class 300Gate Valve - Class 600Gate Valve - Class 900

Gate Valve - Class 1500Gate Valve (PSB) - Class 900

Gate Valve (PSB) - Class 1500Globe Valve - Class 150Globe Valve - Class 300Globe Valve - Class 600Globe Valve - Class 900

Globe Valve - Class 1500Globe Valve (PSB) - Class 900

Globe Valve (PSB) - Class 1500Swing Check Valve - Class 150Swing Check Valve - Class 300Swing Check Valve - Class 600Swing Check Valve - Class 900

Swing Check Valve - Class 1500Swing Check Valve (PSB) - Class 900

Swing Check Valve (PSB) - Class 1500Stainless Steel Gate Valve - Class 150Stainless Steel Gate Valve - Gate 300

Stainless Steel Globe Valve - Class 150/300Stainless Steel Check Valve - Class 150/300

By-Pass & DrainsSteamco Parallel Slide - Class 150-1500

Steamco Stop Check - Class 150-600Steamco Right Angle Globe - Class 150-600

Steamco Non Return Lift - Class 150-600Flowturn Check Cast Iron - Class 125/250

Flowturn Gate Cast Iron - Class 125/250Flowturn Globe Cast Iron - Class 125/250

Technical Considerations

Page 4-5Page 6-8Page 9Page 10Page 11-12Page 13Page 14Page 15Page 16-19Page 20Page 21Page 22Page 23Page 24Page 25Page 26Page 27Page 28Page 290Page 31Page 32Page 33Page 34Page 35Page 36Page 37Page 38Page 39Page 40Page 41Page 42Page 43Page 44Page 45Page 46-49Page 50Page 51Page 52Page 53Page 54-55Page 56Page 57

AUSTRALIAN PIPELINE VALVE™®

page 3

Consistent product quality and availability of substantial stocks, makes Australian Pipeline Valve a dependablechoice for cast gate, globe and check valves, where total reliability is the number one concern.

EXAMPLE

Figure Number System

Trim Types

paRt NUmBeR SyStem

AUSTRALIAN PIPELINE VALVE

TRIM CODE

BODY SEAT SURFACE

DISCSURFACE

STEM BACK SEAT(STUFFING BOX)

X F6 F6 F6 F6

U Stellite Stellite F6 F6

XU Stellite F6 F6 F6

P* F304* F304* F304 F304

L* F316* F316* F316 F316

A* Monel* Monel* Monel Monel

N* Alloy 20* Alloy 20* Alloy 20 Alloy 20

H* Hastelloy B* Hastelloy B* Hastelloy B Hastelloy B

Z* Special Special Special Special

B Bronze Bronze Bronze Bronze

* Note if stellite seat then add XU modifier to end, if stellite seat and disc then add U modifier, if PTFE seat add TF modifier.

Suffix denoting operator g = Gear, Blank = Handwheel or N/A

Suffix denoting end connection (Blank is RF, RJ is RTJ, BW is Buttweld, Sp is special drilling, FF = Flat Face)

Suffix denoting bonnet (p is Pressure Seal, W is Welded, Blank is Bolted)

Suffix denoting valve body material (see page 5)

N denotes NACE, Blank is Non NACE

Blank is standard configuration (example solid wedge) F denotes flexible disc Gate p denotes full opening check (API6D) S denotes Parallel Slide D denotes Globe-Stop Check Z denotes C/W Spring R denotes Right Angle

Denotes trim (see below)

Basic model number (As shown in catalogue)

Valve Size (mm)

150 p47 U F N 9 p BW g -

™®

page 4

Figure Number Codes

Comparative Valve Figure Numbers

BODY MATERIAL CODE • BODY/BONNET AND OR CAP MATERIALSSuffix aStm Spec. material

None A216 Gr. WCB Carbon Steel 1 A216 WCC Carbon Steel2 A352 LCC Low Carbon Steel2B A352 LCB Low Carbon Steel 3 A352 LC3 Low Carbon Steel3M A351 CF3M Stainless with Molybdenum (low carbon)4 A217 WC1 Carbon Moly 1/2% Mo4L A352 LC1 Carbon Moly 1/2% Mo5 A217 Gr. C5 5% Cr, 1/2% Mo6 A217 Gr. WC6 1-1/4% Cr, 1/2% Mo8 A351 CF8 Stainless 18% Cr, 8% Ni8C A351 CF8C Stainless 18% Cr, 10% Ni & Cb8M A351 CF8M Stainless with Molybdenum9 A217 Gr. WC9 2-1/4% CR, 1% Mo12 A217 Gr. C12 Chrome Moly 9% Cr, 1% Mo 19 Bronze Bronze B62/LG2/B14820 AL-Bronze Aluminium Bronze0 SPECIAL

VaLVe type CLaSS apV KItZ WaLWORtH CRaNe VeLaN pOWeLL

gate

VaLVeS

150 P47 150SCL 5202F 47 F-0064C 1503

300 P33 300SCL 5206F 33 F-1064C 3003

600 P76 600SCL 5232F 76 F-2064C 6003

900 P83 900SCL 5247F 83 F-7064C 9003

1500 P87 1500SCL 5262F 87 F-3064C 1303

2500 P25 2500SCL 25003

gLOBe

VaLVeS

150 P143 150SCJ 5275F 143 F-0074C 1531

300 P151 300SCJ 5281F 151 F-1074C 3031

600 P171 600SCJ 5295F 171 F-2074C 6031

900 P183 900SCJ 5301F 183 F-7074C 9031

1500 P189 1500SCJ 5308F 189 F-3074C 1311

2500 P25 2500SCJ

SWINg

CHeCK

VaLVeS

150 P147 150SCO 5341F 147 F-0114C 1561

300 P159 300SCO 5344F 159 F-1114C 3061

600 P175 600SCO 5350F 175 F-2114C 6061

900 P187 900SCO 5353F 187 F-7114C 9061

1500 P199 1500SCO 5356F 199 F-3114C 1361

2500 P25 2500SCO

™®

page 5

CAST STEEL GATE VALVES ANSI CLASS 150 ~ 2500

FEATURES

• Bolted bonnet, OS&Y, Flexible wedge.

• On smaller size valves, the yoke is cast integral withbonnet. Larger size valves have two piece yoke, referto individual drawing.

• Stem nut is mounted with ball bearings toreduce operating torque for ease of manualoperation in larger sizes and higher classes.

• Self aligning two piece gland.

AppLICAbLE STANdARdS

• Valves designed to API Std. 600 andBS 1414

• Valves tested to API Std. 598

• Face-to-face to ANSI B16.10

• Flanged ends to ANSI B16.5

• Butt-welding ends to ANSI B16.25

• Trim and seating surface as per API 600 standard.

Material Combinations/Features

MATERIAL LIST

*1 Lantern Ring where applicable

No.part Name

Carbon Steel alloy Steel Stainless Steel

WCB WCC LCB LCC C5 WC6 WC9 CF8 CF8m CF3 CF3m

apV Suffix Code 1 2B 2 5 6 9 8 8m 0 3m

1 Body A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

2 Seat Ring A105 A105 A350 LF2 A350 LF2 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

3 Wedge A216 WCB A216 WCC A352 LCB A217 CF8 A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

4 Stem A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

5 Bonnet Bolt A193 B7 A320 L7 A193 B16 A320 B8 A193 B8M

6 Bonnet Nut A194 2H A194 4 A194 7 A194 8

7 Gasket Solid metal serrated gasket Stainless Steel & Graphite wound Non-metallic gasket Stainless Steel or Soft Iron Ring Gasket

8 Bonnet A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A217 CF8 A351 CF8M A351 CF3 A351 CF3M

9 Back Seat Bushing A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

10 Stem Packing Braided/Flexible Graphite or PTFE

11 Lantern*1 A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 304L A182 F316L

12 Pin Carbon Steel Stainless Steel Alloy Steel

13 Gland A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

14 Gland Flange A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

15 Gland Eyebolt A307 B A307 L7 A193 B7 A193 B8 A193 B8M

16 Gland Nut A194 2H A194 4 A194 8

17 Stem Nut A439D2 (Austenitic DI) ZCuA110Fe3 (AL-Bronze)

18 Retaining Nut Carbon Steel or Alloy Steel

19 Hand Wheel Ductile Iron or Carbon Steel

20 H.W. Lock Nut Carbon Steel Stainless Steel Alloy Steel

21 Yoke A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

22 Nipple Copper Alloy or Carbon Steel or Stainless Steel

23 Seat/Wedge Facing 13Cr or 16Cr-8Ni or HF(Co-CrA) or 316 or 304

™®

page 6

C

B (Open)

A

NPS

CAST STEEL GLObE VALVES ANSI CLASS 150 ~ 2500

FEATURES

• Bolted bonnet, OS&Y, Swivel Disc.

• Plug type disc (Ball type also available).

• On smaller sizes, the yoke is cast integral with bonnet. Larger sizes have two piece yoke, refer to individual drawing.

• Stem nut is mounted with ball bearingsto reduce operating torque for easeof manual operation in larger sizesand higher classes.

AppLICAbLE STANdARdS

• Valves designed to API Std. 600 and BS 1873






MATERIAL LIST

*1 Lantern Ring where applicable.

No.part Name






3 Disc A105 A216 WCC A350 LF2 A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

4 Stem A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

5 Disc Nut A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

6 Gasket Solid metal serrated gasket Stainless Steel & Graphite spiral wound Non-metallic gasket Stainless Steel or Soft Iron Ring Gasket

7 Bonnet A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

8 Bonnet Bolt A193 B7 A320 L7 A193 B16 A320 B8 A193 B8M

9 Bonnet Nut A194 2H A194 4 A194 7 A194 8

10 Back Seat Bushing A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 304L A182 F316L

11 Stem Packing Braided/Flexible Graphite or PTFE

12 Lantern*1 A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

13 Pin Carbon Steel Stainless Steel Alloy Steel

14 Gland Flange A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

15 Gland A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

16 Gland Eyebolt A307 B A307 L7 A193 B7 A193 B8 A193 B8M

17 Gland Nut A194 2H A194 4 A194 8

18 Stem Nut A439D2 (Austentic DI) ZCuA110Fe3 (AL-Bronze)

19 Handwheel Ductile Iron or Steel

20 H.W. Lock Nut Carbon Steel Stainless Steel Alloy Steel

21 Seat/Disc Facing 13Cr or 16Cr-8Ni or HF(Co-CrA) ST#6 or 316 or 304

™®

page 7

B

(Open)

A

NPS

C

CAST STEEL ChECk VALVESANSI CLASS 150 ~ 2500

FEATURES

• Bolted cover

• Swing disc

AppLIC AbLE STANdARdS

• Valves designed to API Std. 600 6D and BS 1868





• Trim and seating surface as per API 600 standard.


MATERIAL LIST

The material is according to ASTM standard.* Eye bolt supplied in larger sizes & higher classes.

No.part Name






3 Disc A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

4 Disc Nut A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

5 Hinge A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

6 Hinge Pin A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L

7 Gasket Solid metal serrated gasket Stainless Steel & Graphite spiral wound Non-metallic gasket Stainless Steel or CAD Plated Soft Iron Ring Gasket

8 Cover A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M

9 Cover Bolt A193 B7 A320 L7 A193 B16 A193 B8 A193 B8M

10 Cover Nut A194 2H A194 4 A194 7 A194 8

11 Washer Carbon Steel or Alloy Steel or Stainless Steel

12 Seat/Disc Facing 13Cr or 16Cr-8Ni or HF(Co-CrA) ST#6 or 316 or 304

13 Eye Bolt* A193 B7 A320 L7

™®

page 8

A

BN

PS

Physical & Chemical Properties

mateRIaLS

FeRRItIC SteeLSCHemICaL ReQUIRemeNtS (%) meCHaNICaL pROpeRtIeS

Carbon manganese phos- Sulphur Silicon Nickel Chromium molyb- tensile yield elongation Reduction

phorous denum Strength Strength 2” (50mm) of area

N/mm2 N/mm2

CaSt CaRBON SteeL aStm a216, grade WCB

Min - - - - - - - - 485 205 22% 35%

Max 0.35 1.00 0.040 0.045 0.60 - - - 655 - - -

FORgeD CaRBON SteeL aStm a105

Min - 0.60 - - - - - - 485 250 22% 30%

Max 0.35 1.05 0.040 0.05 0.35 - - - - - - -

CaSt CaRBON SteeL FOR LOW tempeRatUReS aStm a352, grade LCB*

Min - - - - - - - - 450 240 24% 35%

Max 0.30 1.00 0.040 0.045 0.60 - - - 620 - - -

CaSt CaRBON mOLy SteeL FOR LOW tempeRatUReS aStm a352, grade LC1*

Min - 0.50 - - - - - 0.45 450 240 24% 35%

Max 0.25 0.80 0.040 0.045 0.60 - - 0.65 620 - - -

CaSt 21⁄2% NICKeL SteeL FOR LOW tempeRatUReS aStm a352, grade LC2*

Min - 0.50 - - - 2.0 - - 485 275 24% 35%

Max 0.25 0.80 0.040 0.045 0.60 3.0 - - 655 - - -

CaSt 31⁄2% NICKeL SteeL FOR LOW tempeRatUReS aStm a352, grade LC3*

Min - 0.50 - - - 3.0 - - 485 275 24% 35%

Max 0.15 0.80 0.040 0.045 0.60 4.0 - - 655 - - -

CaSt CaRBON mOLy SteeL aStm a217, grade WCI

Min - - - - - - - 0.45 450 240 24% 35%

Max 0.25 0.80 0.040 0.045 0.60 - - 0.65 620 - - -

CaSt 11⁄4% CR - 1⁄2% mO aLLOy SteeL aStm a217, grade WC6

Min - 0.50 - - - - 1.0 0.45 485 275 20% 35%

Max 0.20 0.80 0.040 0.045 0.60 - 1.50 0.65 655 - - -

CaSt 21⁄4% CR - 1% mO aLLOy SteeL aStm a217, grade WC9

Min - 0.40 - - - - 2.0 0.9 485 275 20% 35%

Max 0.18 0.70 0.040 0.045 0.60 - 2.75 1.20 655 - - -

CaSt 1 - 6% CR aLLOy SteeL aStm a217, grade C5

Min - 0.40 - - - - 4.0 0.45 620 415 18% 35%

Max 0.20 0.70 0.040 0.045 0.75 - 6.50 0.65 795 - - -

CaSt 9% CR - 1% mO aLLOy SteeL aStm a217, grade C12

M in - 0.35 - - - - 8.0 0.9 620 415 18% 35%

M ax 0.20 0.65 0.040 0.045 1.00 - 10.00 1.20 795 - - -

CaSt 12 - 14% CR aLLOy SteeL aStm a217, grade Ca15

Min - - - - - - 11.5 - 620 450 18% 30%

M ax 0.15 1.00 0.040 0.030 1.50 1.0 14.0 0.50 795 - - -

FORgeD/ROLLeD 12 - 14% CR aLLOy SteeL aStm a182, grade F6a

Min - - - - - - 11.5 - 760 585 15% 35%

Max 0.15 1.00 0.040 0.030 1.00 0.50 13.5 - - - - -

*Usual minimum service temperature : LCB at -46°C (-50°F), LCI at -60°C (-75°F), LC2 at -75°C (100°F), LC3 at -100°C (-150°F)

aUSteNtIC SteeLS

CHemICaL ReQUIRemeNtS (%) meCHaNICaL pROpeRtIeS

Carbon manganese phos- Sulphur Silicon Nickel Chromium molyb- tensile yield elongation Reduction

phorous denum Strength Strength 2” (50mm) of area

N/mm2 N/mm2

CaSt StaINLeSS SteeL WItH mOLyBDeNUm (LOW CaRBON) aStm a351, grade CF3m

Min - - - - - 9.0 17.0 2.0 485 205 30% -

Max 0.03 1.50 0.040 0.040 1.50 13.0 21.0 3.0 - - - -

CaSt StaINLeSS SteeL WItH mOLyBDeNUm aStm a351, grade CF8m

Min - - - - - 9.0 18.0 2.0 485 205 30% -

Max 0.08 1.50 0.040 0.040 1.50 12.0 21.0 3.0 - - - -

CaSt StaINLeSS SteeL WItH COLUmBIUm (NIOBIUm) aStm a351, grade CF8C

Min - - - - - 9.0 18.0 - 485 205 30% -

Max 0.08 1.50 0.040 0.040 2.00 12.0 21.0 0.50 - - - -

ASTM A351-CF8C shall have a columbium content of not less than 8 times the carbon content but not over 1.00%

™®

page 9

API 600 Cast Steel Valves

General Design Specifications

Cast steel valves are designed and manufactured to conform with API, ASTM,ANSI and other applicable internationally recognised standards, to possess all the qualities to meet with stringent requirement criteria of petroleum, petro-chemical and general industrial applications.

Valves are tested in accordance with applicable API standards. Full traceability is maintained.

Valves offer the option of hard facing on the wedge (disc) and seating areas.Lantern rings are furnished as a standard on gate valves of class 300 and above inlarger sizes.

Gate Valves are optionally available with lantern rings. Alongside are illustrations of lantern rings as well as disc connection.

ameRICaN StD. BRItISH StD.

BS1414 (Gate Valve) BS1873 (Globe Valve) BS1868 (Check Valve)

Shell wall thickness and general valve design specifications API 600

Pressure-temperature ratings ANSI B16.34 BS1560

Face-to-face dimensions ANSI B16.10 BS2080 End-to-end dimensions

End flange dimensions ANSI B16.5* BS1560 Gasket contact facing

BS1414 (Gate Valve) BS1873 (Globe Valve) BS1868 (Check Valve)

Welding end dimensions ANSI B16.25

*Valves 28” and larger according to MSS SP-44 or API 605 are available.

™®

page 10

Valve Selection Criteria

Gate Valves

Gate valves are used for bi-directional shut off applications where minimum

pressure drop is required. They are not designed for throttling service.

Gear operators, actuators, by-passes, actuators etc, can be fitted on request.

Parallel slide style also available.

Globe Valves

Globe valves are ideal for throttling and shut off. They can be used for shut

off service, but do have a higher pressure drop than gate valves. Globe

valves should not be used for prolonged throttling at less than 10% open.

Gearboxes, actuators, bypasses etc, can be fitted.

Ratings

Valves must only be used in operating conditions within the correct ANSI

pressure-temperature ratings for valve class rating and body/bonnet

material.

Temperature Limitations

Only use valves within the correct temperature limitations of their con-

struction. Temperature limitations of body/bonnet materials, trim, bolting,

packing and gaskets must all be considered.

™®

page 11

Valve Selection Criteria

Stop Check Valves

Stop check valves are combination globe and check valves. In the open

position, they function as a lift check valve valve. In the closed position, they

are seated by manually closing the stem like a globe valve. Stop check

valves must be installed vertically (in a horizontal pipeline). They provide

positive shutoff in either direction when the stem is in the closed position.

Right angle style are also available.

Swing Check Valves

Swing check valves are used to prevent flow reversal. They are suitable for

service in horizontal or upwards vertical. They have low pressure drop and

are best suited for moderate velocity applications. Either too low a line

velocity or too high a velocity can damage valve internals and shorten valve

life hence correct size selection is important. Service in systems involving

rapid and frequent flow reversals, pulsation or turbulent flow should be

avoided. Also API6D full opening (piggable) type available on request.

™®

page 12

Bolted Bonnet Gate Valves

Features

Full body wedge guides allow correct wedge alignment. Yoke sleeve with

bearings reduce torque for easy operation. Seat rings allow easy access for

maintenance and packing replacement is simple.

Soft seated trim option

All gate valves are available with optional PTFE seat rings. The molded PTFE

ring is bonded into a seat ring groove in the face for maximum service life.

This design is excellent for lower temperature service where tight shutoff is

required.

Parallel slide style also available, see page 46 - 49. 1. handw heel

2. Ris ing Stem - provides open-close indication

3. Grease Fitt ing - to minimise wear and operating torque

4. Yoke Sleeve - furnished in ductile Ni-resist or aluminum-bronze for low torque operation

5. Swing bolt - easier maintenance and packing replacement

6. Gland - flange is self-aligning to eliminate stem damage

7. Stuf fing b ox

8. Stem - upset forge T-head stems to eliminate possibility of abent stem jamming the valve

9. backseat - provides back-up stem seal.

10. bonnet Joint

11. body - full ported, heavy wall body API 600 wall thickness

12. Wedge - heavy pattern. Available in solid & flex wedge

13. Seat Ring - full ported rings for easy maintenance.

14. End Connections - flanged or butt weld ends

Grease injector and lantern ring option

Soft seated “ST” trim option

2

1

3

5

7

9

11

13

4

6

8

10

12

14

™®

page 13

Bolted Bonnet Globe Valves

Operation

Seat rings are easily accessible for repair or replacement. Packing bolts on

most valves simplify packing replacement. Australian Pipeline Valve globe

valves are for services requiring frequent operation and throttling where

pressure drop across the valve is about 20%. Closer throttling, can result in

higher pressure drops which may cause excessive velocities or cavitation

and could cause vibration or high noise levels resulting in damage to the

valve or adjacent components/structure.

Life

Heavy construction provides years of reliable service.

design

Available in bolted and pressure seal bonnet, outside screw and yoke, rising

stem with ball or plug type disc, and have flanged or butt weld ends.

Standards

BS 1873 and ANSI B16.34. Dimensions to ANSI B16.10, BS 2080 and ISO

5752. Wall thickness complies with API 600. 1. Yoke Sleeve - furnished in aluminum-bronze to

reduce torque. Larger sizes furnished with bearings.

2. handwheel

3. Swing bolts - easier maintenance

4. Gland - self-aligning to eliminate stem damage

5. Stuf fing box

6. Stem - heavy duty

7. backseat - provides back-up stem seal

8. bonnet Joint - ring joint or spiral according to ANSIclass

9. Seat Rings - separate heavy duty, full ported rings foreasy maintenance.

10. disc - heavy duty disc plug design

11. End Connections - flanged or butt weld ends

12. body - full ported, with API 600 heavy wall thickness

2

1

3

5

7

9

11

4

6

8

10

12

™®

page 14

Bolted Bonnet Check Valves

Australian Pipeline Valve valves are designed to provide fast valve action and

maximum life. All valves are full ported, have full API 600 wall thickness, and

meet the requirements of ANSI B16.34. Full opening API6D (piggable) type

also available on request.

Features

Valves are designed to close quickly in either horizontal or vertical (flow

up) pipe runs. The body seat ring is installed on a 3o angle. This allows our

check valve to close even when installed in horizontal pipe run with no

pressure.

1. disc Stop - provides positive stop in open position

2. bonnet Joint - (ring or spiral according to class)

3. hinge pin - solid pin for maximum strength

4. Securing Lugs - allow disc to seat freely and preventdisc spinning

5. hinge - designed to withstand shock and load of quickclosing

6. disc - disc is bolted and pinned to hinge; ground seat-ing surface is mated to seat ring for positive shutoff.

7. Seat Ring - Full port seal welded or screwed

8. End Connections - flanged or buttweld

2

1

3

5

7

4

6

8

™®

page 15

Pressure Seal Bonnet Valves

Flexible Wedge Gate Valve

The wedge is a one piece, fully guided wedge. Available in flex wedge and

solid wedge. (Flexible wedge allows the seating faces to move to compen-

sate for thermal expansion). Wedging actions allows a tight seal even in low

differential pressure services. Flexible wedge construction resists wedge

sticking in service where the valve may be closed when hot and opened

when cold. Seating surfaces are hardfaced for long life.

Parallel slide also available, see page 17 and 46 - 49.

1. Yoke Sleeve - aluminum-bronze yoke sleeve has thrustbearings to minimise torque.

2. hand Wheel - (or gear in larger sizes)

3. Yoke - offering ease of maintenance

4. Stem - The design allows the wedge to self-align, eliminatingthe possibility of jamming the wedge.

5. Gland - two piece, self-aligning gland eliminates cocking.Swing out bolting facilitates maintenance.

6. back Seat - Integral, hardfaced

7. pressure Seal - retaining ring and mild steel silver platedgasket to aid disassembly and provide maximum seal.

8. Seat Ring - hardfaced seat rings are welded to body.Tapered design provides clear flow path.

9. Wedge - one-piece, fully guided. Parallel seat also available.

10. body - streamlined flow path minimises pressure drop. API 600 wall thickness.

2

1

3

5

7

9

4

6

8

10

11. Segment RIng

12. Thrust RIng

13. Gasket

14. body

15. bonnet

Flexible Wedge

Exploded View

See E xploded v iew

™®

page 16


parallel Sl ide Gate Valves

Normally utilised for shut off service but are not recommended for

throttling. Gate valves are normally installed in horizontal pipe runs with

the valve stem vertically up. They can be installed in horizontal or vertical

pipe runs. After closing with sufficient force, the stem should be backed off

slightly (1/8 turn) to relieve stem load. Parallel Slide Valves have self aligning

discs with no wedging force and react freely to thermal changes. The design

also ensures uniform seat wear and ease of maintenance. Parallel Slide Gate

Valves are ideal where high differential pressure or thermal expansion may

cause sticking of wedge to gate in traditional gate valves.

2

1

3

5

7

9

4

6

8

10

1. Yoke Sleeve - aluminum-bronze yoke sleeve with thrust bearings for ease of opening.

2. Actuation - Low torque seating design reduces actuationcosts.

3. Yoke - designed to offer ease of maintenance

4. Stem - Threaded into disc housing and also pinned.

5. Gland - two piece, self-aligning gland eliminates cocking. Swingout bolting facilitates maintenance.


7. pressure Seal - retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum seal.

8. Seat Ring - hardfaced seat rings are welded to body and aredesigned for ease of maintenance.

9. discs - Spring loaded discs are self-aligning and reduce actuator torque requirements.

10. Integral Stop - Integral stop positions for reliable seating.

™®

page 17


Globe & SdNR Check Valves

Australian Pipeline Valve Globe valves are installed with pressure and flow

under the disc. Globe valves are suitable for most throttling applications;

they should not be used for throttling at less than 10% open. Stop Check

Valves have a guided loose disc allowing the valve to act as a combination

globe valve and check valve.

2

1

3

5

7

9

4

6

8

10

1. Yoke Sleeve - aluminum-bronze yoke sleeve minimizesoperating torque. Larger sizes have needle bearing typethrust bearings.

2. Actuation - Manual handwheel gear operator or actuated.

3. Yoke - designed to offer ease of maintenance.

4. Stem - precision-ground stem has upset tee-head for reliable stem/wedge connection.

5. Gland - two piece, self-aligning gland eliminates cocking.Swing out bolting facilitates maintenance.


7. pressure Seal - uncomplicated design has segmentedretaining ring and mild steel silver plated gasket to aid disas-sembly and provide maximum bonnet seal.

8. hardened Seating Surfaces - both disc and body seatingsurfaces are hard faced for maximum service life.

9. d isc - fully body guided for positive seating.

10. body - Full port ‘s’ pattern design available to minimisepressure drop.

™®

page 18


Tilt & piston Check Valves

Australian Pipeline Valve Check valves are installed with pressure and flow

under the disc.

2

1

3

4

1. pressure seal design - with retaining ring.

2. Guided disc - for positive seating.

3. Welded in - hardfaced seat ring.

4. Ful l port - S pattern flow path available to minimisepressure drop.

™®

page 19

Gate ValveCat P47Class 150

dIMENSIONS (MM)

dIMENSIONS (MM)

Description material Specs.

Body Carbon Steel A216 Gr. WCB

Bonnet Carbon Steel A216 Gr. WCB

Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF

Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13

Hand Wheel Ductile Iron A536 Gr. 65-45-12

Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF

Back Seat Ring Stainless Steel A276 Gr. 410 or A182 Gr. F6a

Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62

Sleeve Gland Carbon Steel A216 Gr. WCB

Gland Flange Carbon Steel A105

Gland Ring Stainless Steel A182 Gr. F6a

Wheel Nut Carbon Steel A105

Bonnet Bolt Carbon Steel A193 Gr. B7/B7M

Bonnet Nut Carbon Steel A194 Gr. 2H/2HM

Gland Bolt Carbon Steel A193 Gr. B7

Gland Nut Carbon Steel A194 Gr. 2H

Gland Bolt Pin Carbon Steel A108 Gr. 1020

Bearing - Thrust Ball

Grease Nipple Carbon Steel A307 Gr. B

Set Screw Carbon Steel A307 Gr. B

Name Plate Stainless Steel 304/AL

Packing Asbestos Free Reinforced Graphite

Gasket Spiral Wound 304/316 Graphite filled

Standards

Face to Face/End to End ANSI B16.10

Flange Dimensions ANSI B16.5/26” & larger MSS SP-44

Basic Design API 600

Testing API 598

Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 165 178 190 203 229 268 292 330 356 381 406

A. End to End BW 165 216 241 283 305 403 419 457 502 571 610

B. Valve Open 365 390 435 511 610 765 978 1146 1372 1587 1759

C. Hand Wheel Dia 229 229 229 254 305 356 406 457 508 559 559

Weight (Kg) RF * 20 24 28 30 50 85 127 195 283 450 560

For 1⁄2” to 1” dimensions see page 41 and detailed overview brochure.

Size (in) 18” 20” 22” 24” 26” 28” 30” 32” 36” 42” 48”

A. Face to Face RF 432 457 508 508 559 610 610 660 711 787 914

A. End to End BW 660 711 762 813 864 914 914 965 1016 1092 -

B. Valve Open 1930 2156 2346 2515 2721 2896 3130 3264 3588 4610 4842

C. Hand Wheel Dia 559 610 660 660 813 813 813 815 813 813 -

Weight (Kg) RF * 700 900 1050 1350 2000 2400 2800 3400 3820 5900 7300

For 1⁄2” to 1” dimensions see page 41 and detailed overview brochure.For CF8/CF8M 150lb gate see page 41.* For Buttweld weights see detailed overview brochure.

Full Port Design

™®

page 20

A

C

B


dIMENSIONS (MM)

dIMENSIONS (MM)

























Standards


Flange Dimensions ANSI B16.5


Testing API 598

Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 190 216 241 283 305 403 419 457 502 762 838

A. End to End BW 190 216 241 283 305 403 419 457 502 762 838

B. Valve Open 365 429 457 527 619 829 1025 1213 1473 1289 1784

C. Hand Wheel Dia 229 229 229 254 305 406 457 508 559 559 559

Weight (Kg) RF * 20 24 44 50 74 137 217 337 580 715 1050

For 1⁄2” to 1” dimensions see page 42 and detailed overview brochure.

Size (in) 18” 20” 24”

A. Face to Face RF 914 991 1143

A. End to End BW 914 991 1143

B. Valve Open 1965 2194 2578

C. Hand Wheel Dia 610 660 660

Weight (Kg) RF * 1235 1655 2320

For RTJ & 5” dimensions see detailed overview brochure.For CF8/CF8M 300Lb gate see page 42.* For Buttweld weights see detailed overview brochure.

Full Port Design

™®

page 21

A

B

C


dIMENSIONS (MM)

dIMENSIONS (MM)
























Gasket Metal Ring Joint or Spiral Wound SS Graphite filled

Standards




Testing API 598

Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 241 292 330 356 432 559 660 787 838 889 991

A. Face to Face RTJ 241 390 333 359 435 562 664 790 841 892 994

A. End to End BW 241 292 330 356 432 559 660 787 838 889 991

B. Valve Open 362 387 457 514 638 838 1029 1270 1486 1667 1832

C. Hand Wheel Dia 229 229 254 305 406 508 559 559 610 660 660

Weight (Kg) RF 35 48 60 85 135 325 515 840 1100 1360 1910

Weight (Kg) BW 22 38 45 70 105 265 380 700 925 1240 1580

Size (in) 18” 20” 24”

A. Face to Face RF 1092 1194 1397

A. Face to Face RTJ 1095 1197 1400

A. End to End BW 1092 1194 1397

B. Valve Open 2013 2331 2610

C. Hand Wheel Dia 813 813 813

Weight (Kg) RF 2335 2750 4450

Weight (Kg) BW 1900 2150 3660

For 5” and 26” to 36” dimensions see detailed overview brochure.

Full Port Design

™®

page 22

A

B

C


dIMENSIONS (MM)

dIMENSIONS (MM)







Seat Ring Carbon Steel A106 + Stellite/HF

Back Seat Ring Stainless Steel A182 Gr. F6a








Gland Bolt Carbon Steel A193 Gr. B7/B7M

Gland Nut Carbon Steel A194 Gr. 2H.2HM







Gasket Metal Ring Joint or Spiral Wound SS, Graphite filled

Standards



Basic Design* API 600, ANSI B16.34

Testing API 598

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”

A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130 1219

A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232

B. Valve Open 660 702 800 902 1121 1470 1571 1715 1880 2067 2267

C. Hand Wheel Dia 356 406 356 559 610 813 610 610 610 760 -

Weight (Kg) RF 100 140 120 190 460 860 1050 1600 2220 3000 3870

Weight (Kg) BW 80 120 110 180 400 710 830 1350 1890 2565 3300

Size (in) 20”

A. Face to Face RF 1321

A. Face to Face RTJ 1333

B. Valve Open 2440

C. Hand Wheel Dia 760

Weight (Kg) RF 4860

Weight (Kg) BW 4050

For 5” and 24” dimensions & weights see detailed overview brochure.

*10” and over sizes are according to ANSI B16.34

Note: 900LB 2” & 21⁄2“ are the same as 1500LB 2” & 21⁄2”

Full Port Design

™®

page 23

A

B

C


dIMENSIONS (MM)

dIMENSIONS (MM)








Back Seat Ring Stainless Steel A182 Gr. F6a





Wheel Nut Carbon Steel A105 Zn. Plating




Gland Nut Carbon Steel A194 Gr. 2H/2HM







Gasket Metal Ring Joint or Sprial Wound SS Graphite filled

Standards




Testing API 598

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”


A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559

B. Valve Open 590 702 781 879 1181 1343 1511 1711 1880 2067 2267

C. Hand Wheel Dia 356 406 406 559 610 813 915 915 915 - -

Weight (Kg) RF 100 140 180 340 700 1211 2092 2951 4382 6950 9000

Weight (Kg) BW 90 130 160 240 590 986 1765 2586 3659 6000 7740

Size (in) 20”

A. Face to Face RF 1664


A. Short Pattern End to End BW 1473

B. Valve Open 2440

C. Hand Wheel Dia -

Weight (Kg) RF 11130

Weight (Kg)Short PatternBW -

Long Pattern BW 9560

For 5” and 24” dimensions & weights see detailed overview brochure.

*10” and over sizes are according to ANSI B16.34

Full Port Design

™®

page 24

A

B

C

Gate Valve (Pressure Seal)Cat P83Class 900

dIMENSIONS (MM)

dIMENSIONS (MM)













Bonnet Bolt Carbon Steel A193Gr. B7/B7M










Gasket Soft Metal Ring CAD Plated

Standards




Testing API 598

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”


A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232

A. Short Pattern End to End BW 216 254 305 356 508 660 787 914 991 1092 -

B. Valve Open 660 702 690 902 1121 1470 1571 1715 1880 2067 2267

C. Hand Wheel Dia 356 406 356 457 610 610 610 610 610 760 -

Weight (Kg) Short Pattern BW 60 90 80 130 340 590 690 1150 1590 2290 3200

Weight (Kg) Long Pattern BW 66 102 100 150 364 621 739 1295 1790 2465 3200

Weight (Kg) Long Pattern RF 110 140 120 190 460 800 1000 1545 2100 2900 3700

Size (in) 20”

A. Face to Face RF/BW 1321


A. Short Pattern End to End BW -

B. Valve Open 760

C. Hand Wheel Dia -

Weight (Kg)Short PatternBW 3636

Weight (Kg)Long PatternBW 4050

Weight (Kg) RF 4860

For 5” and 24” (Long Pattern) dimensions see detailed overview brochure.

*Note: 10” and over sizes are according to ANSI B16.34

Note: 900LB 2” & 21⁄2“ are the same as 1500LB 2” & 21⁄2”

Full Port Design

™®

page 25

A

C

B

Gate Valve (Pressure Seal)Cat P87Class 1500

dIMENSIONS (MM)

dIMENSIONS (MM)












Wheel Nut Carbon Steel A105 Zn. Plating












Standards




Testing API 598

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”


A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559

A. Short Pattern End to End BW 216 254 305 406 559 711 864 991 1167 1194 1346

B. Valve Open 590 702 781 879 1181 1343 1511 1711 1880 2067 2267

C. Hand Wheel Dia 356 406 457 559 610 760 813 813 - - -




Size (in) 20”



A. Short Pattern End to End BW 1473

B. Valve Open 2440

C. Hand Wheel Dia -

Weight (Kg)Short PatternBW 7980

Weight (Kg)Long PatternBW 9560

Weight (Kg) RF 11130

For 5” and 24” (Long Pattern) dimensions see detailed overview brochure.

*Note: 10” and over sizes are according to ANSI B16.34

™®

page 26

Full Port Design

A

C

B

Globe ValveCat P143Class 150

Full Port Design

dIMENSIONS (MM)





Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a



Back Seat Ring Stainless Steel A276 Gr.410 or A182 Gr. F6a



Disc Gland Stainless Steel A217 Gr. CA-15

Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62



Gland Bolt Carbon Steel A193 Gr.B7



Wheel Nut Stainless Steel A192 Gr. 8/A105




Standards



Basic Design API 600*

Testing API 598

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 203 216 241 292 406 495 622 698.5 787 914

A. End to End BW 203 216 241 292 406 495 622 698.5 787 914

B. Valve Open 330 365 413 463 536 616 746 832 1375 1569

C. Hand Wheel Dia 203 229 254 305 356 406 559 559 600 600

Weight (Kg) RF 20 26 35 65 113 190 238 410 560 890

Weight (Kg) BW 18 22 28 55 93 170 215 370 500 795

For RTJ dimensions and 5” dimensions, see detailed overview brochure.For 1/2” to 1 1/2” see page 43 and detailed overview brochure.For CF8/CF8M Globe 150Lb see page 43.

*Stem is Based on B.S 1873

™®

page 27

A

B

C


Full Port Design

dIMENSIONS (MM)





Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a










Gland Bolt Carbon Steel A193 Gr.B7/2HM







Standards




Testing API 598

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 267 292 317 356 444 559 622 711 838 863

A. End to End BW 267 292 317 356 444 559 622 711 838 863

B. Valve Open 356 400 448 537 625 800 990 1170 1380 1480

C. Hand Wheel Dia 205 229 254 305 406 559 559 559 700 -

Weight (Kg) RF 30 37 60 90 176 333 340 550 765 1100

Weight (Kg) BW 25 30 52 75 150 320 280 520 - -

For RTJ dimensions 2” - 16” and 5” RF/RTJ dimensions, see detailed overview brochure.For 1⁄2” to 11⁄2” see page 43 and detailed overview brochure. For CF8/CF8M Globe 300# see page 43.


™®

page 28

A

B

C


Full Port Design






















Standards




Testing API 598

dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 292 330 356 432 559 660 787 838 889 991

A. Face to Face RTJ 295 333 359 435 562 663 790 841 892 994

A. End to End BW 292 330 356 432 559 660 787 838 892 994

B. Valve Open 425 438 546 663 889 997 865 1101 1426 1431

C. Hand Wheel Dia 254 305 356 457 559 660 610 660 - -

Weight (Kg) RF 39 56 68 121 280 450 720 950 1750 2260

Weight (Kg) BW 35 44 59 97 230 380 580 830 - -

For 1⁄2” to 11⁄2” see detailed overview brochure.


™®

page 29

A

B

C


Full Port Design






















Standards




Testing API 598

dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130

A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140

A. Short Pattern End to End BW 216 254 305 256 508 660

B. Valve Open 597 648 724 832 1019 1181 1540 1840 2135 2380

C. Hand Wheel Dia 406 457 457 559 750 750 750 - - -

Weight (Kg) Short Pattern BW 60 85 80 130 229 1110

Weight (Kg) Long Pattern BW 73 110 95 150 310 1225 1345 1900 2130 2860

Weight (Kg) Long Pattern RF 98 130 110 180 440 1346 1400 2220 2650 3300

Note:- 900LB 2” & 21⁄2” are the same as 1500LB 2” & 21⁄2”Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.


™®

page 30

A

B

C

Globe Valve Cat P189Class 1500

Full Port Design








Back Seat Ring Carbon Steel A276 Gr.410 or A182 Gr. F6a













Gasket Metal Joint or Spiral Wound SS Graphite filled

Standards




Testing API 598

dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12”

A. Face to Face RF/BW 368 419 470 546 705 832 991 1130

A. Face to Face RTJ 371 422 473 549 708 835 1000 1146


B. Valve Open 597 648 724 816 1019 1181 1610 1950

C. Hand Wheel Dia 406 457 559 610 813 - - -


Weight (Kg) Long Pattern BW 98 130 170 255 590 1290 1700 2600

Weight (Kg) Long Pattern RF 73 110 140 230 540 1190 1480 2300

Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.

*Stem is based on B.S. 1873

™®

page 31

A

B

C

Globe Valve(Pressure Seal Bonnet)Cat P183Class 900

Full Port Design






















Standards




Testing API 598

dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130

A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140


B. Valve Open 597 648 724 832 1019 1181 1540 1840 2135 2380

C. Hand Wheel Dia 406 457 559 610 813 813 - - - -


Weight (Kg) Long Pattern BW 70 120 90 150 320 1225 1325 1900 2130 2860

Weight (Kg) Long Pattern RF 90 140 100 170 480 1346 1400 2200 2650 3300

Note 900LB 2” & 21⁄2” are the same as 1500LB 2” & 21⁄2”Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.


™®

page 32

A

B

C

Globe Valve(Pressure Seal Bonnet)Cat P189Class 1500

Full Port Design






















Standards




Testing API 598

dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12”

A. Face to Face RF/BW 368 419 470 546 785 832 991 1130

A. Face to Face RTJ 371 422 473 549 708 835 1000 1146


B. Valve Open 597 648 724 832 1019 1181 1600 1950

C. Hand Wheel Dia 406 457 559 610 813 813 - -




Note 900LB 2” & 21⁄2” are the same as 1500LB 2” & 21⁄2”Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.


™®

page 33

A

B

C

Swing Check ValveCat P147Class 150



Cover Carbon Steel A216 Gr. WCB


Hinge Carbon Steel A276 Gr. 410 or A182 Gr. F6a/CR13

Hinge Pin Stainless Steel A182 Gr. F6a/CR13


Plug Carbon Steel A108 Gr. 1045

Cover Bolt Carbon Steel A193 Gr. B7/B7M

Cover Nut Stainless Steel A194 Gr. 2H/2HM

Disc Nut Stainless Steel A563 Gr. B

Washer Stainless Steel A276 Gr. 410

Eye Bolt Carbon Steel A105

Name Plate Stainless Steel 304 AL


Standards




Testing API 598

dIMENSIONS (MM)

dIMENSIONS (MM)

Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 165 203 216 237 292 356 495 622 698 787 864

A. End to End BW 165 203 216 237 292 356 495 622 698 787 864

B. Valve Open 114 140 140 156 184 292 353 371 416 489 521

Weight (Kg) RF 11 15 23 33 44 78 137 207 279 428 555

Weight (Kg) BW 8.5 12 16 24 34 63 122 175 229 368 483

Size (in) 18” 20” 24” 28” 30”

A. Face to Face RF 978 978 1295 1448 1524

A. End to End BW 978 978 1295 1448 1524

B. Valve Open 559 590 702 710 870

Weight (Kg) RF 775 835 1300 1450 1620

Weight (Kg) BW 685 720 1150 1300 1450

For RTJ dimensions see detailed overview brochure.For 5” dimensions see page 44 and detailed overview brochure.For 1⁄2” to 1” dimensions see page 44 and detailed overview brochure..For CF8/CF8M 150Lb see page 44.

*Also meets design requirements for ANSI B16.34

Full Port Design

™®

page 34

A

B






Hinge Carbon Steel A216 Gr WCB



Plug Carbon Steel A108 Gr.1045


Cover Nut Carbon Steel A194 Gr. 2H/2HM

Disc Nut Carbon Steel A563 Gr. B

Washer Stainless Steel A276 Type 410

Eye Bolt Carbon Steel A307 Gr. B



Standards




Testing API 598

dIMENSIONS (MM)

dIMENSIONS (MM)

Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”

A. Face to Face RF 241 267 292 317 356 444 533 622 711 838 864

A. End to End BW 241 267 292 317 356 444 533 622 711 838 864

B. Valve Open 140 149 165 184 209 305 368 410 457 514 565

Weight (Kg) RF 12 21 24 39 60 90 175 210 300 700 774

Weight (Kg) BW 10 15 17 30 50 68 145 180 260 490 640

Size (in) 18” 20” 24” 28” 30”

A. Face to Face RF 978 1016 1346 1499 1595

A. End to End BW 978 1016 1346 1499 1595

B. Valve Open 714 746 780 790 820

Weight (Kg) RF 1000 1273 1650 1725 1819

Weight (Kg) BW 850 1100 1400 1570 1700

For RTJ dimensions see detailed overview brochure.For 5” dimensions see page 44 and detailed overview brochure.For 1⁄2” to 1” dimensions see page 44 and detailed overview brochure.For CF8/CF8M 300Lb see page 44.


Full Port Design

™®

page 35

A

B

















Standards



Basic Design* API 600

Testing API 598

dIMENSIONS (MM)

dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”

A. Face to Face RF 292 330 356 432 559 660 787 838 889 991 1092

A. Face to Face RTJ 295 333 359 435 562 664 791 841 8912 994 1095

A. End to End BW 292 330 356 432 559 660 787 838 991 991 1092

B. Valve Open 159 184 197 292 352 397 492 556 737 650 771

Weight (Kg) RF 28 38 55 87 207 354 580 790 892 1200 1600

Weight (Kg) BW 20 30 42 65 155 280 490 670 750 1020 1350

Size (in) 20” 24”

A. Face to Face RF 1194 1397

A. Face to Face RTJ 1200 1407

A. End to End BW 1194 1397

B. Valve Open 800 900

Weight (Kg) RF 2420 3150

Weight (Kg) BW 2050 2720


Full Port Design

™®

page 36

A

B

















Standards




Testing API 598

*10” and over sizes are according to ANSI B16.34All sizes meet the design requirements for ANSI B16.34

dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”


A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232

A. Face to Face Short Pattern BW 216 254 305 356 508 660 757 914 991 1092

B. Valve Height 340 371 302 333 413 495 571 535 686 757 819




dIMENSIONS (MM)

Size (in) 20”



B. Valve Height 867

Weight (Kg) Long Pattern BW 3100

Weight (Kg) Long Pattern RF 3500

Full Port Design

™®

page 37

A

B

















Standards




Testing API 598


dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”


A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559


B. Valve Height 260 271 302 333 413 495 571 635 686 756 819




dIMENSIONS (MM)

Size (in) 20”




B. Valve Height 2600

Weight (Kg) Short Pattern BW 4809

Full Port Design

™®

page 38

A

B

Swing Check Valve(Pressure Seal Bonnet)Cat P187Class 900
















Standards




Testing API 598


dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”


A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232


B. Valve Height 260 271 302 333 413 495 571 535 686 757 819




dIMENSIONS (MM)

Size (in) 20”



B. Valve Height 867

Weight (Kg) BW 3103

Weight (Kg) Long Pattern RF 3500

Full Port Design

™®

page 39

A

B

Swing Check Valve(Pressure Seal Bonnet)Cat P199Class 1500
















Standards




Testing API 598


dIMENSIONS (MM)

Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”


A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559


B. Valve Height 260 271 302 333 413 495 571 635 686 756 819




dIMENSIONS (MM)

Size (in) 20”




B. Valve Height 2600

Weight (Kg) Short Pattern RF 4809

Full Port Design

™®

page 40

A

B

Stainless Steel Gate ValveCat P47Class 150

Features• Investment cast to 300NB (12”)• Self aligning gland flange• Larger sizes fitted with thrust bearings for ease of operation• Yoke sleeve made from AL-Bronze or Austenitic DI for corrosion & wear resistance.


Body Stainless Steel A351 Gr. CF8/CF8M

Bonnet Stainless Steel A351 Gr. CF8/CF8M

Disc Stainless Steel A351 Gr. CF8/CF8M

Stem Stainless Steel A182 Gr. F304/F316

Hand Wheel Malleable Iron A197

Yoke Sleeve Austenitic DI A439 Gr. D2C or NR Bronze

Gland Flange Stainless Steel A351 Gr. CF8/CF8M

Gland Ring Stainless Steel A182 Gr. F304/F316

Wheel Nut Stainless Steel A351 Gr. CF8/CF8M

Bonnet Bolt Stainless Steel A193 Gr. B8

Bonnet Nut Stainless Steel A194 Gr. 8

Gland Bolt Stainless Steel A193 Gr. B8

Gland Nut Stainless Steel A194 Gr. 8

Gland Bolt Pin Stainless Steel A182 Gr. F304


Grease Nipple Bronze B62 Cr. Plating

Set Screw Stainless Steel A193 Gr. B8

Name Plate Stainless Steel A240 Type 304

Packing Asbestos Free PTFE/Graphite

Bonnet Gasket PTFE or Graphite Sheet or 316 + Graphite SPW

Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M or ST #6

Back Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M

Standards



Basic Design ANSI B16.34, API 600/API603

Testing API 598

dIMENSIONS (MM)

Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10”

Size (mm) 15 20 25 40 50 65 80 100 150 200 250

A. Face to Face RF 108 117.5 127 165 178 190.5 203 229 267 292 330

A. End to End BW 114 117.5 127 165 216 241 282.5 305 403 419 457

B. Valve Open 178 200 210 250 300 356 406 583 660 813 991

C. Hand Wheel Dia 102 102 127 152 178 179 203 229 254 305 356

Weight (Kg) RF * 4.2 5.2 7.1 11.1 16.1 18.2 22.7 39.1 64.1 101.4 150.9

150 CLASS

*Weights are for API603. For API600 weights see Page 20. For Buttweld weights and RTJ dimensons seedetailed overview brochure.

dIMENSIONS (MM)

Size (in) 12” 14” 16” 18” 20” 24”

Size (mm) 300 350 400 450 500 600

A. Face to Face RF 356 381 406 432 457 508

A. End to End BW 502 571.5 609.6 660 711 813

B. Valve Open 1194 1346 1524 1651 1829 2184

C. Hand Wheel Dia 406 508 559 559 609.6 660

Weight (Kg) RF * 218.1 288.6 341 659 841 1105

150 CLASS

Full Port Design

™®

page 41

A

C

B

Stainless Steel Gate ValveCat P33Class 300







Yoke Sleeve Austenitic DI A439 Gr. D2C or NR Bronze



Wheel Nut Stainless Steel A351 Gr. CF8/CF8M







Grease Nipple Bronze B62 Cr. Plating

Set Screw Stainless Steel A193 Gr. B8


Packing Asbestos Free PTFE/Graphite




Standards



Basic Design ANSI B16.34, API 600 or API603

Testing API 598

dIMENSIONS (MM)

Size (in) 10” 12” 14” 16” 18” 20” 24”

Size (mm) 250 300 350 400 450 500 600

A. Face to Face RF 457 502 762 838 914 991 1143

A. End to End BW 457 502 762 838 914 991 1143

B. Valve Open 1016 1219 1372 1549 1956 2184 2565

C. Hand Wheel Dia 457 508 559 559 609.6 609.6 762

Weight (Kg) RF * 284 409 614 773 1250 1364 2614

300 CLASS

dIMENSIONS (MM)

Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10”

Size (mm) 15 20 25 40 50 65 80 100 150 200 250

A. Face to Face RF 140 152 165 190 216 241 282.5 305 403 419 457

A. End to End BW 140 152 165 190 216 241 282.5 305 403 419 457

B. Valve Open 200 200 210 250 300 381 432 508 686 864 1016

C. Hand Wheel Dia 100 100 140 203 203 203 229 254 356 406 457

Weight (Kg) RF * 6.1 7.9 9.7 15 19.5 30 40.9 60 111 184.5 284

300 CLASS

*Weights are for API603. For API600 weights see Page 21. For Buttweld weights and RTJ dimensons seedetailed overview brochure.

Full Port Design


™®

page 42

A

C

B

Stainless Steel Globe ValveCat P143/P151Class 150-300









Disc Gland Stainless Steel A351 Gr. CF8/CF8M

Yoke Bush Austentic DI A439 Gr. D2C or NR Bronze






Wheel Nut Stainless Steel A194 Gr. 8


Packing Asbestos Free PTFE or Graphite




Standards



Basic Design ANSI B16.34/BS1873/API603

Testing API 598

dIMENSIONS (MM)

Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12”

Size (mm) 15 20 25 40 50 65 80 100 150 200 250 300

A. Face to Face RF 108 117.5 127 165 178 190.5 203 229 267 292 330 356

A. End to End BW 114 117.5 127 165 216 241 282.5 305 403 419 457 502

B. Valve Open 178 200 210 250 300 356 406 583 660 813 991 1194

C. Hand Wheel Dia 102 102 127 152 178 179 203 229 254 305 356 406

Weight (Kg) RF * 4.2 5.2 7.1 11.1 16.1 18.2 22.7 39.1 64.1 101.4 150.9 218.1

dIMENSIONS (MM)

Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12”

Size (mm) 15 20 25 40 50 65 80 100 150 200 250 300

A. Face to Face RF 140 152 165 190 216 241 282.5 305 403 419 457 502

A. End to End BW 140 152 165 190 216 241 282.5 305 403 419 457 502

B. Valve Open 200 200 210 250 300 381 432 508 686 864 1016 1219

C. Hand Wheel Dia 100 100 140 203 203 203 229 254 356 406 457 508

Weight (Kg) RF * 6.1 7.9 9.7 15 19.5 30 40.9 60 111 184.5 284 409

300 CLASS

150 CLASS

*Weights are for ANSI B16.34. For API600 weights see Page 27. For 14” to 16” dimensions see detailed overview brochure. For Buttweld weights and RTJ dimensions see detailed overview brochure.

Full Port Design


™®

page 43

A

B

C

Stainless Steel Check ValveCat P147/P159Class 150-300

*For API600 weights see page 34, 35.For Buttweld dimensons and weights see detailed overview brochure. For RTJ dimensions see detailed overview brochure.For 16” to 30” see detailed overview brochure.

parts Name materials

Body ASTM A351 Gr. CF8/CF8M

Bonnet ASTM A351 Gr. CF8/CF8M

Disc ASTM A351 Gr. CF8/CF8M

Arm ASTM A276 Gr. CF8/CF8M

Hinge Pin ASTM A276 Gr. 304/316

Split Pin AISI 304/316

Disc Nut AISI 304/316

Disc Washer AISI 304/316

Bonnet Bolt / Nut ASTM A193 Gr. B7/A194 Gr. 8/B8M

Gasket Teflon or Graphite or 316/GRP SPW

Plug ASTM A276 Gr. 304/316

Plug Gasket Teflon

Eye Bolt* ASTM A193 B8

Seat (Integral) ASTM A351 Gr. CF8/CF8M or ST #6

* Larger sizes only

dIMENSIONS (MM)

Size (in) 10” 12” 14”

Size (mm) 250 300 350

A. Face to Face 622 698 787

B. Centre Top 318 357 420

Weight (Kg) RF* 190 260 400

dIMENSIONS (MM)

Size (in) 1⁄2” 3⁄4” 1” 11⁄4” 11⁄2” 2” 21⁄2” 3” 4” 5” 6” 8”

Size (mm) 15 20 25 32 40 50 65 80 100 125 150 200

A. Face to Face 152 178 203 229 241 267 292 318 356 400 444 533

B. Centre Top 76 78 83 89 16 129 143 164 177 217 249 312

Weight (Kg) RF* 7 8 10 10 11 18 21 35 50 70 80 160

300 CLASS

150 CLASS

dIMENSIONS (MM)

Size (in) 1⁄2” 3⁄4” 1” 11⁄4” 11⁄2” 2” 21⁄2” 3” 4” 5” 6” 8”

Size (mm) 15 20 25 32 40 50 65 80 100 125 150 200

A. Face to Face 108 117 127 140 165 203 216 241 292 330 356 495

B. Centre Top 73 75 80 86 111 123 134 148 158 192 223 283

Weight (Kg) RF* 6 7 8 8 10 13 20 30 40 60 70 120

150 CLASS

dIMENSIONS (MM)

Size (in) 10” 12” 14”

Size (mm) 250 300 350

A. Face to Face 622 711 838

B. Centre Top 359 394 474

Weight (Kg) RF* 200 270 660

300 CLASS

Full Port Design

Features• Investment cast to 300NB (12”)• Larger sizes fitted with thrust bearings• Wall thickness ANSI B16.34

Standards



Basic Design ANSI B16.34/BS186873/API603

Testing API 598

™®

page 44

A

B

By-Pass & Drains

Gate Valve

Globe Valve

Check Valve

ball Valve

Valve Size 2” - 4” 5” - 8” 10”-24”

Drain and By-Pass Size

1⁄2” 3⁄4” 1”

Valve Size 2” - 4” 5” - 8” 10”-24”

Drain and By-Pass Size

11⁄2” 13⁄4” 21⁄8”

™®

page 45

STANDARDS COMPLIANCE:Basic Design: API 600, ANSI B16.34, BS 5157Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or AS/BS2129 Table D to RPressure/Temperature ratings to ANSI B16.5/BS 1560

For installation in applications such as industrial, mining and mechanicalservices. Suitable for super-heated steam, H.T.H.W steam condensate andwater.

This design consists of two discs, kept in contact with parallel body seats,using the line pressure and seating action to effect tight closure.

Temperature changes in the line are accommodated by the expanding discand do not affect the action of the valve. When being opened or closed,the discs slide across the seat faces, dislodging any foreign matter. Thevalve operating stem is outside screw rising through the handwheel.

These valves are suitable for full bore steam use, where a low pressuredrop across the valve is required. Also suitable for water, oil, gas, etc.

O.S. & Y. Rising Stem Full Port, Expanded ParallelSlide Gate Valve, Double Disc, Pressure Seal orBolted Bonnet, Welded-in or Threaded Seat Rings.Mechanically loaded seating for low and highpressure sealing.

Parallel slide dual loaded discs ensure superiorshut off and allow by-pass/bleed fitment (doubleblock and bleed requires soft seat inserts).

Pressure/temperature charts available on request.

Buttweld ends

(Spring loaded DoubleDisc Style)

™®™®

pReSSURe/ tempeRatURe WCB BODy

For superheated steam etc. consult chart. WC6 chrome-moly available body for high temperature applications.

Parallel Slide Gate ValveCat P316SClass 150-1500 (BS/AS Table D to T)

StaNDaRD mateRIaL SpeCIFICatIONS

Class Cat No.

Test Pressure to API598 (PSIG) Working Pressure

Shell(Hydro)

Seat(Hydro)

Seat(Air)

CWPWOG

Saturated Steam(at 260°C)*

150(BST D to F)

150-P316SXU-S 450 315 80 280 170

300(BST H to J)

300-P316SXU-S 1125 815 80 720 600

600(BST K to R)

600-P316SXU-S 2225 1628 80 1440 1200

900(BST S)

900-P316SXU-S 3350 2442 80 2190 1800

1500(BST T)

1500-P136SXU-S 5626 4078 80 3600 3000

Part Material

1 Body ASTM A216 Gr. WCB

2 Spreader ASTM A182 Gr. F6

3 Seat Ring ASTM A105 + HF

4 Parallel Disc ASTM A216 Gr. WCB + F6/HF

5 Stem ASTM A182 Gr. F6

6 Bolt ASTM A193 Gr. B7

7 Nut ASTM A194 Gr. 2H

8 Gasket Stainless Steel/Graphite

9 Bonnet ASTM A216 Gr. WCB

10 Back Seat ASTM A182 Gr. F6

11 Packing Braided Graphite

12 Packing Flexible Graphite

13 Gland ASTM A182 Gr. F6

14 Gland Flange ASTM A216 Gr. WCB

15 Eye-Bolt ASTM A193 Gr. B7

16 Nut ASTM A194 Gr. 2H

17 Stem Nut ASTM A439 Gr. D2

18 Retaining Nut ASTM A105

19 Handwheel ASTM A395

20 Handwheel Nut Steel

21 Pin ASTM A182 Gr. F6

22 Spring Inconel X750

22

4

™®

page 46

C

B

A

Parallel Slide Gate ValveCat P316SClass 150-1500 (BS/AS Table D to T)

SeatingCode

Body SeatSurface Part

No. 3

Double DiscSurface Part

No. 4

StemPart No. 5

Back Seat(Stuffing Box)Part No. 10

X F6 F6 F6 F6



P* F304 F304 F304 F304

R* F316 F316 F316 F316

M* Monel Monel Monel Monel

N* Alloy 20 Alloy 20 Alloy 20 Alloy 20

H* Hastelloy B Hastelloy B Hastelloy B Hastelloy B

tRIm mateRIaL CODeS (tO apI 600)

Body Material Codes

None A216 WCB

0 Special

5 A217 C5

6 A217 WC6

8 A351 CF8

8M A351 CF8M

9 A217 WC9

VALVE SIZE(NPS)

inch 2 21⁄2 3 4 5 6 8 10 12 14 16 18 20 24

mm 50 65 80 100 125 150 200 250 300 350 400 450 500 600

CLASS150

(BST D to F)

D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591

A mm 178 190 203 229 254 267 292 330 356 381 406 432 457 508

B (Open) mm 409 472 490 612 720 806 990 1186 1415 1583 1771 1955 2210 2698

C mm 200 200 250 250 350 350 350 450 500 560 640 720 800 900

Weight (kg) RF 20 25 38 55 75 85 134 198 320 400 524 690 900 1350

CLASS300

(BST F to J)

D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591

A-A1 mm 216 241 283 305 354 403 419 457 502 760 838 914 991 1143

B (Open) mm 428 477 543 650 720 850 1037 1276 1438 1585 1960 2155 2350 2720

C mm 200 250 250 300 300 350 450 500 560 640 720 800 900 1118

Weight (kg) RF 25 44 50 74 124 137 217 337 580 715 1050 1235 1655 2320

CLASS600

(BST J to R)

D mm 51 64 76 102 125 152 203 254 305 337 387 438 489

A-A1 mm 292 330 356 432 508 559 660 787 838 889 991 1092 1192

B (Open) mm 474 553 593 654 857 970 1122 1330 1519 1716 2110 2400 2461

C mm 250 250 300 350 400 500 560 720 720 720 900 1000 1000

Weight (kg) RF 50 60 85 135 260 345 515 845 1120 1360 1910 2335 2700

CLASS900

(BST S to T)

D mm 51 60 76 102 120 152 203 254 305 324 375 438

A-A1 mm 372 419 384 460 559 613 740 841 968 1039 1140 1219

B (Open) mm 590 702 740 870 1051 1078 1318 1581 1867 2004 2178 2526

C mm 250 300 300 350 450 560 640 800 800 900 900 900

Weight (kg) RF 110 140 150 220 355 460 800 1050 1600 2220 3000 3870

OVeRaLL DImeNSIONS (mm) & WeIgHt (kg)

* Add XU modifier to end of model suffix if stellite seat, if stellite seat & disc add Umodifier to end.

Note: 15mm to 40mm NB also available refer to individual drawings.

™®

page 47

pReSSURe/ tempeRatURe WCB BODy

™®™®

Parallel Slide Gate ValveCat P316HClass 150-1500 (BS/AS Table D to T)

The P316H style parallel slide is the same dimensions as the P316S except haspillar type top works. The P316H also has spring energised discs.

For installation in applications such as industrial, mining and mechanical services. Suitable for super-heated steam, H.T.H.W steam condensate andwater.

This design consists of two discs, kept in contact with parallel body seats, usingthe tension spring to effect tight closure.

Temperature changes in the line are accommodated by the energised discs anddo not affect the action of the valve. When being opened or closed, the discsslide across the seat faces, dislodging any foreign matter. The valve operatingstem is outside screw rising through the handwheel (OSY).

These valves are suitable for full bore steam use, where a low pressure dropacross the valve is required. Also suitable for water, oil, gas, etc.

STANDARDS COMPLIANCE:Basic Design: API 600/BS EN 1984/S 5157/ANSI B16.34Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or BS/AS2129 Table D to RPressure/Temperature Ratings to ANSI B16.34/BS 1560

O.S. & Y. Rising Stem, Full Port, Expanded ParallelSlide Gate Valve, Double Spring energised Discs,Pressure Seal or Bolted Bonnet, Welded-in or ThreadedSeat Rings. Spring energised loaded seating for lowand high pressure sealing.

Parallel slide dual loaded discs ensure superior shut offand allow by pass/bleed fitment (double block andbleed requires soft seat inserts).

Buttweld ends


3/4

C

B

A

D R P O

For superheated steam etc. consult chart. * WC6 chrome-moly available body for high temperature applications.

Class Cat No.

Test Pressure to API598 (PSIG) Working Pressure

Shell(Hydro)

Seat(Hydro)

Seat(Air)

CWPWOG

Saturated Steam(at 260°C)*

150(BST D to F)

150-P316HXU-S 450 315 80 280 170

300(BST H to J)

300-P316HXU-S 1125 815 80 720 600

600(BST K to R)

600-P316HXU-S 2225 1628 80 1440 1200

900(BST S)

900-P316HXU-S 3350 2442 80 2190 1800

1500(BST T)

1500-P136HXU-S 5626 4078 80 3600 3000

Z-d

C 1.6

™®

page 48

part material

1 Body ASTM A216 Gr. WCB2 Seat Ring ASTM A105 + HF3 Spring Inconel X 7504 Spring Coil AISI 4105 Parallel Disc ASTM A216 Gr. WCB + F6/HF6 Bushing AISI 4107 Pin AISI 4108 Stem ASTM A182 Gr. F69 Gasket Stainless Steel/Graphite10 Bolt ASTM A193 Gr. B711 Nut ASTM A194 Gr. 2H12 Back Seat Ring ASTM A182 Gr. F613 Packing Flexible Graphite14 Packing Braided Graphite15 Gland ASTM A182 Gr. F616 Gland Flange ASTM A216 Gr. WCB17 Bolt ASTM A193 Gr. B718 Nut ASTM A194 Gr. 2H19 Bonnet ASTM A216 Gr. WCB20 Bolt ASTM A194 Gr. 2H21 Supporting Pole 104522 Guide Pole 104523 Yoke Plate 102524 Bolt ASTM A194 Gr. 2H25 Supporting Disc 102526 Stem Nut D-227 Retaining Nut 103528 Handwheel A4729 Handwheel Nut 1035


Parallel Slide Gate ValveCat P316HClass 150-1500 (BS/AS Table D to T)

Note:- 15NB to 40NB also available. Refer to drawings

SeatingCode

Body SeatSurface Part

No. 2

Double DiscSurface Part

No. 5

StemPart No. 8

Back Seat(Stuffing Box)Part No. 12

X F6 F6 F6 F6



P* F304 F304 F304 F304

R* F316 F316 F316 F316

M* Monel Monel Monel Monel

N* Alloy 20 Alloy 20 Alloy 20 Alloy 20

H* Hastelloy B Hastelloy B Hastelloy B Hastelloy B

tRIm mateRIaL CODeS (tO apI 600)

* Add XU modifier to end of model suffix if stellite seat, if stellite seat & disc add U

modifier to end.

VALVE SIZE(NPS)

inch 2 21⁄2 3 4 5 6 8 10 12 14 16 18 20 24

mm 50 65 80 100 125 150 200 250 300 350 400 450 500 600

CLASS150

(BST D to F)

D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591

A mm 178 190 203 229 254 267 292 330 356 381 406 432 457 508

B (Open) mm 409 472 490 612 720 806 990 1186 1415 1583 1771 1955 2210 2698

C mm 200 200 250 250 350 350 350 450 500 560 640 720 800 900

Weight (kg) RF 20 25 38 55 75 85 134 198 320 400 524 690 900 1350

CLASS300

(BST F to J)

D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591

A-A1 mm 216 241 283 305 381 403 419 457 502 760 838 914 991 1143

B (Open) mm 428 477 543 650 720 850 1037 1276 1438 1585 1960 2155 2350 2720

C mm 200 250 250 300 300 350 450 500 560 640 720 800 900 1118

Weight (kg) RF 25 44 50 74 124 137 217 337 580 715 1050 1235 1655 2320

CLASS600

(BST J to R)

D mm 51 64 76 102 125 152 203 254 305 337 387 438 489

A-A1 mm 292 330 356 432 508 559 660 787 838 889 991 1092 1192

B (Open) mm 474 553 593 654 857 970 1122 1330 1519 1716 2110 2400 2461

C mm 250 250 300 350 400 500 560 720 720 720 900 1000 1000

Weight (kg) RF 50 60 85 135 260 345 515 845 1120 1360 1910 2335 2700

CLASS900

(BST S to T)

D mm 51 60 76 102 120 152 203 254 305 324 375 438

A-A1 mm 372 419 384 460 559 613 740 841 968 1039 1140 1219

B (Open) mm 590 702 740 870 1051 1078 1318 1581 1867 2004 2178 2526

C mm 250 300 300 350 450 560 640 800 800 900 900 900

Weight (kg) RF 110 140 150 220 355 460 800 1050 1600 2220 3000 3870

™®

page 49

Body Material Codes

None A216 WCB

0 Special

5 A217 C5

6 A217 WC6

8 A351 CF8

8M A351 CF8M

9 A217 WC9

p143XU-D 150 CLaSS (to BSt-F)280 PSI CWP (WOG)170 PSI Saturated Steam (at 260ºC)

p151XU-D 300 CLaSS (to BSt-J)

720 PSI CWP (WOG)600 PSI Saturated Steam (at 260ºC)For superheated steam consult pressure/temp chart

p171XU-D 600 CLaSS (to BSt-R)1440 PSI CWP (WOG) 1100 psi at 260°C, 825 psi at 400°C. For other temperatures consult chart.

Screw Down Non Return“Stop Check” Globe ValveCat P143-D/P151-D/P171-DClass 150-600 (BS/AS Table D to R)

For horizontal installations in applications such as industrial, miningand mechanical services. Suitable for super-heated steam, H.T.H.W.,steam, condensate and water.

FEATURES:Screw-Down Non-Return Globe ValveGuided loose disc for combination checkand stop.Bolted Bonnet, O.S. & Y., Swivel Disc .25% maximum carbon content on WCB.

STANDARDS COMPLIANCE:Basic Design: API 600/AS1873 and ANSIB16.34Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or BS/AS2129 Table D to RPressure/Temperature Ratings to ANSIB16.34.

* Fitted on larger sizes & higher classes. Other Body and Trim materials available such as WC6, bronze, etc. See detailed overview brochure.

Buttweld ends

WORKINg pReSSURe

Overall Dimensions (mm & in) & Weight (kg)


™®™®

*Available in undrilled to accommodate BS table drilling. ANSI flanges can also be machined to BStable thickness to allow face to face dimension alteration. 1⁄2” to 11⁄2” see page 48.

Part Name Materials

1 Body ASTM A216 Gr. WCB*

2 Seat Ring ASTM A105 with HF overlay

3 Disc ASTM A105 with F6 overlay


5 Gasket Spiral Wound 316/GRP

6 Gasket Ring Joint CAD Plated

7 Bonnet ASTM A216 Gr. WCB (or WC6)

8 Bonnet Bolt ASTM A193 Gr. B7

9 Bonnet Nut ASTM A194 Gr. 2H

10 Back Seat Bushing ASTM A182 Gr. F6

11 Stem Packing Braided graphite (top & Bottom)

12 Stem Packing Flexible graphite

13 Lantern Ring*1 ASTM A182 Gr. F6



16 Gland Flange ASTM A216 Gr. WCB

17 Gland Bolt ASTM A193 Gr. B7

18 Gland Nut ASTM A194 Gr. 2H

19 Yoke Bush Gr. D2C or Bronze B62

20 Handwheel A536/A197

21 Wheelnut ASTM A105

VALVE SIZE (NPS)

inch 2 21⁄2 3 4 5 6 8 10 12mm 50 65 80 100 125 150 200 250 300

CLASS 150*(BST D TO F)

A-A1

(RF-BW)inch 8 81⁄2 91⁄2 111⁄2 14 16 191⁄2 241⁄2 271⁄2mm 203 216 241 292 356 406 495 622 698.5

B (Open)inch 133⁄4 147⁄8 16 177⁄8 223⁄8 221⁄2 247⁄8 291⁄8 393⁄8mm 349 378 407 454 569 573 632 740 1000

Cinch 8 10 10 12 15 16 18 20 20mm 200 250 250 300 390 400 450 500 500

Weight(kg)

inch 22 31 37 58 103 111 179 240 410mm 19 25 26 50 95 101 159 215 370

CLASS 300*(BST F TO J)

A-A1

(RF-BW)inch 101⁄2 111⁄2 121⁄2 14 153⁄4 171⁄2 22 241⁄2 28mm 267 292 318 356 400 444.5 559 622 711

B (Open)inch 141⁄4 151⁄2 167⁄8 19 263⁄8 265⁄8 301⁄2 407⁄8 541⁄8mm 362 394 429 482 669 676 774 1040 1375

Cinch 8 10 12 14 16.9 18 20 20 20mm 200 250 300 350 430 450 500 500 500

Weight(kg)

inch 28 47 54 76 150 162 270 340 550mm 22 40 43 61 130 136 232 280 520

CLASS 600*(BST J TO R)

A-A1

(RF-BW)inch 111⁄2 13 14 17 22 26 31 33mm 292 330 356 432 559 660 787 838

A (RTJ)inch 115⁄8 131⁄8 141⁄8 171⁄8 221⁄8 261⁄8 311⁄8 331⁄8mm 295 333 359 435 562 664 791 841

B (Open)inch 191⁄2 211⁄8 231⁄4 281⁄8 385⁄8 443⁄4 503⁄32 582⁄3mm 495 537 590 714 981 1136 1276 1490

Cinch 10 12 14 16 22 24 24 267⁄8mm 250 300 350 400 550 600 600 680

Weight(kg)

inch 51 62 85 143 340 520 720 950mm 42 51 72 120 284 465 580 830

™®

page 50

C

B

A

Screw-Down Non-Return Globe Valve (combination globeand check valve), Bolted Bonnet, O.S. & Y., Swivel Disc(guided loose disc for combination check and stop). Orcan be supplied as standard globe stop valve. Drilling toANSI and table D to R AS/BS2129.

WORKING PRESSUREp143R 150 CLaSS (to BSt-F)

280 PSI CWP (WOG)170 PSI Saturated Steam (at 260ºC)p151R 300 CLaSS (to BSt-J)

720 PSI CWP (WOG)600 PSI Saturated Steam (at 260ºC)For superheated steam consult pressure/temp chartp171R 600 CLaSS (to BSt-R)

1440 PSI CWP (WOG) for high temperature, consult chart

WC6 body is available for high temperature applications.

Buttweld ends

™®™®

*On larger sizes and higher classes.Note: Other trim materials are available upon request, such as bronze.

For installations in application such as industrial, mining and mechanical services. Suitable for super-heated steam, H.T.H.W, steam, condensate and water.Stem is guided for smooth operation.Also available in Bronze, Iron, chrome-moly etc.

“Right Angle StyleScrew Down Non ReturnStop Check” Globe Valve

Cat P143-R/P151-R/P171-RClass 150-600 (BS/AS Table D to R)

No Part Material

1 Body ASTM A216 Gr. WCB or WC6


3 Disc ASTM A105 with F6 overlay


5 Gasket S/S Spiral Wound Graphite filled

6 Bonnet ASTM A216 Gr. WCB or WC6



9 Back Seat Bushing ASTM A182 Gr. F6

10 Stem Packing Braided graphite (top & bottom)

11 Stem Packing Flexible graphite

12 Lantern Ring* ASTM A182 Gr. F6



15 Gland Flange ASTM A216 Gr. WCB or WC6

16 Gland Eyebolt ASTM A193 Gr. B7

17 Gland Nut ASTM A194 Gr. 2H

18 Stem Nut ASTM A439 Gr. D2

19 Handwheel ASTM A395

20 H.W. Lock Nut Steel


VALVE SIZE(NPS)

inch 2 21⁄2 3 4 5 6 8 10 12

mm 50 65 80 100 125 150 200 250 300

CLASS 150

(BST D TO F)

L* (RF-BW) mm 102 ⁄114 146 ⁄108 121 ⁄159 152 ⁄165 178 203 ⁄216 241 ⁄248 305 ⁄311 305 ⁄349

B (Open) mm 373 390 420 500 550 565 670 770 880

C mm 200 250 250 300 390 390 450 550 600

O mm 152 178 191 229 254 279 343 406 483

Weight (kg)RF 22 31 377 58 103 111 179 240

BW 19 25 26 50 95 101 159 215 35

CLASS300

(BST F TO J)

L* (RF-BW) mm 133 117 ⁄127 140 ⁄159 146 ⁄178 178 ⁄191 222 279 311 349 ⁄355

B (Open) mm 390 425 485 580 700 770 900 1020 700

C mm 200 250 300 350 430 450 500 600 600

O mm 165 191 210 254 279 318 381 445 520

Weight (kg)RF 28 47 54 76 150 162 270

BW 22 40 43 61 130 136 232 394

CLASS600

(BST J TO R)

L* (RF-BW) mm 146 165 178 216 279 330 1450 419

B (Open) mm 423 498 575 750 1030 1290 1300 1504

C mm 250 300 350 450 600 650 650 650

O mm 165 191 210 273 356 419 510 560

Weight (kg)RF 51 62 85 143 340 520

BW 42 51 72 120 284 465


* Two patterns are available hence 2 dimensions have been shown.Up to 400NB also available.

STANDARDS COMPLIANCE:Basic Design: BS1873/ANSI B16.34Test: API Standard 598 Flanged Ends: ANSI B16.5B.W. Ends: ANSI B16.25Face to Face Dimension: BS2820 or ANSI B16.10Pressure/Temperature Ratings to ANSI B16.34.

™®

page 51

C

B

O

Od

L*

L*

Non Return - Lift TypeCat SLCLClass 150-600 (BS/AS Table D to R)

Non return valve, lift type, bolted bonnet, guided disc. Flangedrilling ANSI 150 to 600 and AS2129 table D to R.For horizontal installations in applications such as industrial,mining and mechanical services. Suitable for super-heatedsteam, H.T.H.W., steam, condensate and water.Guiding of stem assures smooth operation.Other body materials like Bronze and WC6 also available.

SLCL-SSpring Activated

SLCLXU-Z 150 CLaSS (to BSt-F)

280 PSI CWP (WOG)170 PSI Saturated Steam (at 260°C)SLCLXU-Z 300 CLaSS (to BSt-J)

720 PSI CWP (WOG)600 PSI Saturated Steam (at 260°C)For superheated steam consult pressure/temp chartSLCLXU-Z 600 CLaSS (to BSt-R)

1440 PSI CWP (WOG)1100 PSI at 260°C, 825 psi at 400°C. Consult chart for other temperaturesWC6 body is available for high temperature applications

*1 Spring Optional.*2 Drain Optional.

Buttweld ends

WORKING PRESSURE

OVeRaLL DImeNSIONS (mm & inches) & WeIgHt (kg)


™®™®

VALVE SIZE (NPS)inch 2 21⁄2 3 4 5 6 8 10 12

mm 50 65 80 100 125 150 200 250 300

CLASS 150(BST D to F)

A-A1

(RF-BW)

inch 8 81⁄2 91⁄2 111⁄2 14 16 191⁄2 241⁄2 271⁄2

mm 203 216 241 292 356 406 495 622 698.5

Binch 67⁄8 7 71⁄2 85⁄8 91⁄4 123⁄4 151⁄8 175⁄8 211⁄4

mm 175 178 191 219 235 324 384 448 540

Weight(kg)

inch 20 24 35 55 84 96 160 245 345

mm 14 17 26 37 52 80 133 213 294

CLASS 300(BST F to J)

A-A1

(RF-BW)

inch 101⁄2 111⁄2 121⁄2 14 153⁄4 171⁄2 21 241⁄2 28

mm 267 292 318 356 400 444 533 622 711

Binch 73⁄4 8 83⁄4 107⁄8 115⁄8 131⁄4 161⁄4 181⁄4 221⁄8

mm 197 203 222 276 295 337 413 464 562

Weight(kg)

inch 35 37 60 82 110 155 268 380 495

mm 32 35 50 65 70 128 230 270 460

CLASS 600(BST J to R)

A-A1

(RF-BW)

inch 111⁄2 13 14 17 20 22 26 31 33

mm 292 330 356 432 508 559 660 787 838

Binch 81⁄4 85⁄8 101⁄2 113⁄4 131⁄4 15 183⁄4 215⁄8 225⁄8

mm 210 219 267 299 337 381 476 549 670

Weight(kg)

inch 40 55 72 120 175 270 420 620 810

mm 31 45 60 85 125 225 365 500 715

Part Name Materials

1 Body ASTM A216 Gr. WCB


3/4 Disc/Stem ASTM A105 with F6 overlay

5 Gasket Stainless Steel/Graphite

6 Bonnet ASTM A216 Gr. WCB



9*1 Spring Inconel X750

10 Gasket Graphite

11*2 Drain Plug A105N

STANDARDS COMPLIANCE:Basic Design: API 600/BS1873 and ANSI B16.34Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or BS/AS2129 Table D to R

™®

page 52

A

B

Check Cast Iron BodyANSI Class 125-250 • SL404-SL404F

MATERIAL LIST

* Ductile Iron Body for 250 Class/and PN16 in larger sizes.*2 Bronze or stainless trim

dIMENSIONS & WEIGhTS

ASA125 cold working pressure:-200 PSI to 300NB, 150 PSI 350NB to 600NB.PN16 also available 1600 kpa C.W.P (232 PSI)ANSI 250 Class available to 12 inch (whichcan be drilled BS Table F)(Ductile Iron Body)

Swing checkConforming to MSS SP-71End Flange Dimensions: ANSI B16.5 or PN16/BS/ASFace to Face Dimensions: ANSI B16.10, BS5153, MSS-SP71Maximum temperature 210 ºCDrilled to suit ANSI Class 125 or PN10, PN16, JIS and AS/BS2129Table D to F. ANSI 250 Class and PN16 also available up to 300NB

™®

Part Name Material

1 Cover Bolt & Nut Steel

2 Cover* ASTM A126 Class B

3 Gasket Graphite

4 Hanger Pin Stainless Steel or F6

5 Hanger ASTM A126 Class B

6 Disc Ring ASTM B62 or F6

7 Disc ASTM A126 Class B

8 Disc Washer Steel

9 Disc Bolt Steel

10 Seat Ring*2 ASTM B62 or F6

11 Body* ASTM A126 Class B

Class Size (in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24”

125

A 203 216 241 292 330 356 495 622 699 787 864 978 978 1295

A1 508

B 131 146 157 182 330 237 278 313 353 434 470 535 570 679

Weight 11 15 20 34 47 58 104 252 313 396 560 725 881 1276

250

A 267 292 318 356 445 533

A1 133 152 159 184 229 279

Weight 21 29 41 60 114 186

MM & kG

1

2

3

4

5

6

7

8

9

10

11 A/A1

B

™®

page 53

Gate Cast Iron BodyANSI Class 125/250/PN16 • SL600 - SL600F

™®1000 Kpa rated SL600-10

1600 Kpa rated SL600-16

Drilled to suit class 125 or AS/BS2129 Table C to F, PN10, PN16, JIS.Inside screw & yoke, solid wedge disc, bolted bonnet, non rising stemConforming to MSS SP-70/BS5150/5163End Flange Dimensions: ANSI B16.5/PN16/BS/ASFace to Face: ANSI B16.10, BS5150/BS5163/MSS-SP70 (PN16)Ductile Iron Body for ANSI 150 Class and PN16 in larger sizes.

MATERIAL LIST

NOTE: *Bronze B16 or stainless steel CR13/304/316 on request.Maximum temperature 210°C

NOTE: NPS above 600NB (24") can be furnished on request

dIMENSIONS & WEIGhTS MM & kG

Part Name Material

1 Body ASTM A126 Class B

2 Seat Ring ASTM B62 (bronze*)

3 Wedge Face Ring ASTM B62 (bronze*)

4 Wedge ASTM A126 Class B

5 Stem* Bronze/Brass/F6

6 Body Gasket Graphite

7 Bolt Steel B7

8 Nut Steel 2H

9 Bonnet ASTM A126 Class B

10 Back Seat Bushing Cast Brass

11 Packing Graphite

12 Packing Gland Cast Brass/410SS

13 Packing Gland Bolt Alloy Steel B7

14 Gland Flange Nut Alloy Steel 2H

15 Gland Flange Cast Brass/410SS

16 Yoke Bushing Nut ASTM A126 Class B

17 Handwheel ASTM A126 Class B

18 Identification Plate Aluminium

19 Handwheel Nut Ductile Iron

Class Size(mm) 50 65 80 100 125 150 200 250 300 350 375 400 450 500 600 700 750

(in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 15” 16” 18” 20” 24” 28” 30”

125

A (mm) 178 191 203 229 254 267 292 330 356 381/441 406/476 406/476 432/505 457/510 508/575 610

B (mm) 313 334 370 430 454 550 678 750 880 940 950 1080 1180 1380 1480 1670

C (mm) 203 203 203 254 254 305 356 406 457 508 560 559 610 610 762 910

Weight 15 21 26 44 61 74 127 216 283 375 638 550 600 840 1170

250

A (mm) 216 241 282 305 403 419 457 502

B (mm) 315 340 390 440 460 560 678 798 895

C (mm) 203 229 254 305 406 508 559 610

Weight 23 41 54 84 166 272 418 636

Z-ød

ASA125: 200 PSI max cold working pressure 50NB to 300NB, 150 PSI350NB to 600NB, PN16 (232 PSI) also available.ANSI 150 rating also available in ductile iron body

C

B

A

™®

page 54

Gate Cast Iron BodyANSI Class 125-250 • SL601 - SL601F

NOTE: Special face to face dimensions also available.

dIMENSION & WEIGhTS MM & kG

MATERIAL LIST

™®

Part Name Material

1 Body ASTM A126 Class B*1

2 Seat Ring ASTM B62 or F6*2

3 Wedge Face Ring ASTM B62 or F6*2

4 Wedge ASTM A126 Class B

5 Stem Bronze/410SS


7 Bolt Steel

8 Nut Steel


10 Back Seat Bushing Cast Brass/410SS

11 Packing Graphite

12 Packing Gland Cast Brass/410SS

13 Packing Gland Bolt Steel

14 Gland Flange Nut Steel

15 Yoke Bushing Ductile Iron

16 Gland Flange Cast Brass/410SS

17 Yoke Bushing Nut ASTM A126 Class B

18 Screw Steel

19 Handwheel*3 ASTM A126 Class B

20 Identification Plate Aluminium

21 Handwheel Nut Ductile Iron or B62

Class Size (in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24”

125

A 178 191 203 229 254 267 292 330 356 381 406 432 457 508

B 375 408 441 545 656 770 959 1260 1486 1689 1860 2106 2295 2768

C 203 203 203 254 254 305 356 406 457 508 559 610 610 762

Weight 15 21 26 44 61 74 127 216 315 409 640 726 782 1353

250

A 216 241 282 205 403 419 457 502

B 368 445 521 629 876 1092 1340 1524

C 203 229 254 305 406 508 559 610

Weight 23 41 54 84 166 272 418 636

ANSI Class 125 or AS/BS2129 Table C to F as well as PN10,PN16, JIS etc. Also 250 Class & PN16 available up to 300NBOutside screw & Yoke, solid wedge disc, bolted bonnet.Conforming to MSS SP-70/BS5163/MSS-SP70End Flange Dimensions: ANSI B16.5/PN16/AS/BSFace to Face: ANSI B16.10/BS5150/BS5163/MSS-SP70210°C Maximum TemperatureANSI 150 & PN16 rating also available in Ductile Iron Body

*1 250 Class is Ductile Iron Body.

*2 Available in 304, 316, 410, Bronze or Brass trim

*3 For Gear Operated version refer to drawing.

ASA 125: 200 PSI max cold working pressure 50NB to 300NB, 150 PSI 350Nbto 600Nb, PN16 (232 PSI) also available.150 and 250 Class also available to 300NB (12 inch) Ductile Iron Body.

C

B

A

™®

page 55

Globe Cast Iron BodyANSI Class 125-250 • SL201 - SL201F

MATERIAL LIST

* 150 & 250 Class in Ductile Iron Body.Bronze or stainless steel stem on request.Maximum temperature 210oC

ASA 125: 150 PSI max cold working pressure 350NB to 600NB, 200 PSI 50NB to 300NB. PN16 (232PSI) also available.150 Class also available to 12 inch.

™®

dIMENSION & WEIGhTS MM & kG

Class Size (in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24”

125

A 203 216 241 292 330 356 495 622 699 787 864 978 978 1295

B 335 356 392 446 489 516 663 832 1270 1430 1430

C 203 203 229 254 305 305 406 508 600 600 600

Weight 23 27 34 54 71 95 180 325 340 396 560 725 881 1276

250

A 267 292 318 356 445 533

B 349 375 419 470 591 724

C 229 254 254 305 406 508

Weight 28 37 54 73 145 259

Part Name Material

1 Body ASTM A126 Class B

2 Seat Ring ASTM B62 or F6

3 Disc ASTM A126 Class B

4 Disc Stem Ring ASTM B62 or F6

5 Back Seat Bushing Cast Brass or F6


7 Nut Steel

8 Bolt Steel

9 Packing Graphite

10 Packing Gland Cast Brass or F6

11 Gland Flange Ductile Iron


13 Yoke Bushing Cast Brass or F6

14 Stem ASTM B16 or F6A

15 Handwheel ASTM B126 Class B

16 Handwheel Nut Ductile Iron

Class 125 cold working pressure:- 200 PSI to 200NB, 150 PSI200NB to 400NB (PN16-232 PSI also available). ANSI 150 and250 Class also available to 300NB in Ductile Iron Body

Conforming to MSS SP-85/BS5152End Flange Dimensions: ANSI B16.1/PN16Face to Face: ANSI B16.10/MSS-SP85/BS5152Drilled to suit ANSI 125 (ASA150) and BS table D to F, PN10,PN16 etc

C

B

A

™®

page 56

Australian Pipeline Valve don’t consider in our design the following factors of risk:

1. Australian Pipeline Valve “Standard” valves can be used in a temperature range between -29/+490°C. (Note, pressure limitations apply above 38°C refer to Pressure/Temperature charts.) For service temperatures below -29°C valves construction materials shall be submitted to an impact test at the minimum servicetemperature. For temperatures above and below the standard range, special seals need to be specified bythe client.

2. The onus is on the customer to specify all materials of construction and service conditions. Australian Pipeline Valve shall assume standard materials and conditions if not otherwise specified.

3. Australian Pipeline Valve “Standard” valves are not equipped with devices suitable to avoid internal over-pressures caused by incorrect operations of process or by fluids & liquids subjected to an increase of volume and/or pressure (these devices, such as the over pressure hole into the gate or safety seats are available upon request).

4. Australian Pipeline Valve “Standard” valves are not designed with special devices to withstand a sudden thermal jump (thermal shock).

5. In general Australian Pipeline Valve “Standard” valves are not mechanically designed to bear overloads due to exceptional atmospheric or natural phenomenon’s (such as earthquakes).

6. In general Australian Pipeline Valve “Standard” valves are not designed to bear loads on flanges, on pipe connections or pipe-line.

7. In general Australian Pipeline Valve “Standard” valves can’t withstand ice inside their bodies (in this case user has to consider the optional stem extension for insulating, avoiding the presence of residual product inside the valve).

8. Australian Pipeline Valve “Standard” valves are not suitable for low temperature service below - 46°C (-51°F) unless supplied (in suitable body material) with cryogenic stem extension and other modifications, (available on request).

9. Australian Pipeline Valve “Standard” valves are suitable for “industrial” oxygen (not medical) service when supplied degreased and packed in polyethylene bags only.

10. The compatibility between the valves construction materials and medium is selected by the user. The user is ultimately responsible for verifying the compatibility between medium and materials.

11. Abrasive or dirty service applications need to be considered and stated at time of order.

VALVE START-UP

Before installing the valve onto the pipe-line it is mandatory, for the user, to verify the compatibility of the valve with serv-ice conditions (medium, temperature and pressure). With reference to standard valves held in stock, the reseller and enduser will have to assure themselves of the compatibility between the valve and the conditions required by the customer.Australian Pipeline Valve gate valves must be only used for on-off (fully open/fully closed) service.

Before using the valve in a potential explosive atmosphere it’s necessary for the customer to: -

• To verify the correct type of valve and operator is specified.• To verify the compatibility between the valve and the zone in which the valve should be installed• To foresee the pipe-line ground condition on which the valve should be installed• To check that the temperature if the valve surface is not higher than the flammable point of the atmosphere

in which the valve is installed (in this case specify an insulating cover device for the valve and an extensionfor the operator)

• To avoid mechanical knocks during the installation that may cause sparks.

Australian Pipeline Valve cannot be held responsible for damage caused by use of the product for any reason, especiallyif it is improper use or modified.

CONSIDERATIONS OF TECHNICAL RISK / LIMIT OFLIABILITY FOR APV GATE, GLOBE, CHECK VALVES

™®

page 57

Local distributor

QUALITY

ASSURANCE

We are continually improving all facets of quality assurance. Full metalurgical and test certificates are always supplied for all pressure retaining parts, we also provide it on all majortrim components.

We have endeavoured to provide a broad outline of our range and capabilities. Because weare continually developing new products for our customers the brochure will, to some extent beincomplete. This catalogue is a general overview only, individual drawings and data sheets relevant to valve supplies can be furnished on request. Therefore if you have any requirementsin the field of valves please contact us for a prompt response. Continuous development ofAustralian Pipeline Valve products may necessitate changes in the design or manufacturingprocesses. Australian Pipeline Valve reserves the right to affect any such changes withoutprior notice.

CERTIFICATIONCERTIFICATION

™®

Valve_Cast_Steel_Gate_Globe.pdf

Documents

Transcript of Valve_Cast_Steel_Gate_Globe.pdf