VALENTINO ROSSI’S - US website · 2019. 4. 15. · VALENTINO ROSSI’S Pack 15. Editorial and...
Transcript of VALENTINO ROSSI’S - US website · 2019. 4. 15. · VALENTINO ROSSI’S Pack 15. Editorial and...
VALENTINO ROSSI’S
Pack 15
Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE. Published in the USA by De Agostini Publishing USA, Inc.,121 E. Calhoun Street, Woodstock, IL 60098.All rights reserved © 2019
Warning: Not suitable for children under the age of 14. This product is not a toy and is not designed or intended for use in play. Items may vary from those shown.
STAGE PAGE
55 Gear lever assembly 193
56 The airbox duct 196
57 The subframe 199
58 The subframe air intake 202
VALENTINO ROSSI’S
IN COLLABORAZIONE CON
IN COLLABORATION with
193BUILD THE YAMAHA YZR -M1
A
STAGE 55
Your parts
GEAR LEVER ASSEMBLY
B
C
D
E
F
A
A. Upper plate
B. Gear lever
C. Linkage
D. Type K screws x 3
E. Type X screws x 3
F. Type G screws x 2
194 STEP BY STEP
STEP 03 Secure the lever to the bracket with a type X screw. Don’t overtighten the screw, so the lever can move freely.
STEP 01 Retrieve the footpeg bracket and the left footpeg from Stage 54. Fit the footpeg to the bracket, as shown.
STEP 02 Fit the gear lever to the indicated hole in the bracket.
STEP 04 Fix the linkage to the gear lever with a type X screw. Make sure the parts are positioned correctly, as shown.
STEP 05 Fit the two pins on the inside of the top plate into the corresponding holes in the top of the bracket.
01
05
03
02
04
Pin
Type X screw
195BUILD THE YAMAHA YZR -M1
STEP 08Fit the free end of the tube onto the linkage pin.
STEP 09 Fix the free end of the linkage to the arm at the side of the engine block with a type G screw. Check that when you press on the left footpeg, that the linkage and the arm move back.
STEP 06 Take the left footpeg assembly and fit the two holes at the front over the corresponding holes in the rear of the frame.
STEP 07 Secure the footpeg assembly to the frame with two type K screws. Locate the indicated tube.
STAGE COMPLETEThis is how the assembly should look at the end of this stage.
09
07
08
06
COMPLETE
Tube
Type G screw
196 STEP BY STEP
A
STAGE 56
Your parts
THE AIRBOX DUCT
B
C
A
A. Upper duct half
B. Lower duct half
C. Type C screws x 3
197BUILD THE YAMAHA YZR -M1
STEP 02 Join the two halves of the duct together, as shown.
STEP 04 Place the airbox into position, to match the one shown here.
STEP 01 Locate the posts and matching holes in the two halves of the duct.
STEP 03 Retrieve the airbox assembled in Stage 37. The holes in the bottom of the airbox match with those in the throttle bodies.
01
03
04
02
198 STEP BY STEP
STEP 05 Take the duct and insert it into the front of the airbox, as shown.
STEP 07 Tighten a type C screw into the aligned holes to secure the right side of the duct.
STEP 06 Align the holes in the underside of the duct with the corresponding holes in the frame.
STEP 08 Tighten another type C screw into the aligned holes on the left side of the duct.
STAGE COMPLETEThis is how the assembly should look at the end of this stage.
08
06
05
07
COMPLETE
199BUILD THE YAMAHA YZR -M1
A
STAGE 57
Your parts
THE SUBFRAME
BC
D
E
A
A. Subframe
B. Fairlead
C. Connector
D. 40mm tube
E. 165mm tube
200 STEP BY STEP
STEP 01 Locate the two holes in the left side of the subframe.
STEP 02 Push the pins in the fairlead into the two holes in
the side of the subframe.
STEP 03 Fit the 165mm tube to the straight end of the connector, as shown.
STEP 04 Fit the 40mm tube to the rounded end of the connector.
01
0403
02
165mm40mm
201BUILD THE YAMAHA YZR -M1
STEP 05 Bend the 40mm tube as shown, and fit it onto the indicated pin.
STEP 06 Clip the 165mm tube into the circled fairlead on the side
of the frame.
STAGE COMPLETE This is how the assembly should look at the end of this stage.
06
05
COMPLETE
165mm
202 STEP BY STEP
A
STAGE 58
Your parts
THE SUBFRAME AIR INTAKE
B
C
D
A
A. Lower air intake half
B. Upper air intake half
C. Plate
D. Type I screws x 3
203BUILD THE YAMAHA YZR -M1
STEP 02 Place the lower air intake half into position on the subframe, as shown.
STEP 01 Take the subframe
(Stage 57) and align the holes
in the lower air intake
half with the indicated
posts.
STEP 03 Fix the lower air intake half to the subframe with two type I screws.
02
01
03
204 STEP BY STEP
STEP 04 Join the upper air intake half to the lower half, as shown.
STAGE COMPLETEThis is how the assembly should look at the end of this stage.
STEP 05 Insert the pins of the plate into the indicated holes in the air intake, with the tab (blue arrow) facing forward.
STEP 06 Here you can see the plate in the correct position.
06
04
05
COMPLETE