UZIN NC 150 - Montclair State University · Project Plus Self Leveling Compound ... adhesive...

UZIN NC 150Self-drying leveling compound. Provides smooth fi nish for resilient fl oor coverings.

Project Plus Self Leveling Compound

Description:UZIN NC 150 is a cementitious, self leveling and smoothing compound formulated for use at depths up to 1" (25 mm). It works well for producing level, flat surfaces with high absorbency for standard preparation and cost effective installations in areas with normal wear demands. For interior use only.

Suitable for/on:3 Producing level, fl at, smooth substrates with high absorbency,

for the application of carpet and all types of resilient fl oor covering

3 Producing fl at surfaces for installing ceramic tile, natural stone and engineered wood fl ooring

3 Existing substrates, including thin and dense non-water-soluble adhesive residues on concrete, including cutback adhesive residues (see “Important Notes”)

3 Effi cient and economical standard leveling work for residential and commercial projects with normal wear requirements

3 Radiant fl oor heating systems, (hydronic or electric)

Product Properties:UZIN NC 150 is a modifi ed dry powder mortar. When mixed with water it produces a cement leveling compound with excellent fl ow properties providing a cost effective, highly productive product for standard leveling work which sets to accept foot traffi c after 2 – 3 hours.

Composition: Special cements, mineral aggregates, polyvinyl acetate copolymers, fl ow agents and additives.

Features• Pumpable• Fast setting

• Smooth surface• Low stress• High compressive

and tensile strengths• Significantly longer

working time• Meets strict EMICODE

EC 1 R PLUS criteria• Compliant with California

Sect. 01350 specifi cation

Benefi ts• Minimizes time and effort• Accepts most floor coverings

after 24 hours*• Improves adhesive coverage rate• Ability to cover difficult substrates• Exceeds most flooring requirements

for suitable surface• Greater jobsite flexibility

• Healthy indoor air quality

• LEED V4 contributing product

Technical Data:Packaging: 50 lb. (22.7 kg) paper bag

Storage: minimum 6 months

Water ratio: refer to product packaging

Color: light grey

Coverage rate: 29 sq. ft. at 1/4" depth per 50 lb. bag(approx.) (2.69 m² at 6 mm depth per 22.7 kg bag)

actual coverage may vary depending on substrate conditions

Working temperature: min. 60 °F (16 °C) at floor level

Working time: 20 – 40 minutes*

Set to foot traffi c: after approx. 2 – 3 hours *

Ready for covering: after approx. 24 hours*

Compressive strength: 4150 psi after 28 days (ASTM C109M-12)

Flexural strength: 900 psi after 28 days (ASTM C348-08)* At 70 °F (21 °C) and 65% relative humidity.Depth of application and surface porosity will affect dry time.

UZIN. YOUR FLOOR. OUR PROMISE.

Ideal for Most

Floor Coverings

UFLOOR Systems Inc. | toll free 866-505-4810 | 720-374-481014509 E. 33rd Place, Unit G, Aurora CO 80011 | ufloorsystems.com

LEED®

contributingproduct

UZIN NC 150

Substrate Preparation:The subfloor must be structurally sound, solid, dry, free from active cracks, clean and free of all contaminants such as grease, oil, paint, wax, curing and sealing compounds that would impair adhesion. Test the substrate in accordance with applicable standards relative to moisture content. Any weakly bonded or soft surface material such as loose adhesive residues, leveling compounds, floor coverings or coatings must be removed by shot blasting, abrading, grinding or wet scraping. Thoroughly vacuum off all loose material or dust. CAUTION: Do not sand or grind adhesive residue, as harmful dust may result. Inhalation of asbestos dust may cause asbestosis or other serious bodily harm. Refer to the Resilient Floor Covering Institute’s publication “Recommended Work Practices for Removal of Resilient Floor Coverings” for instructions. Select a suitable primer from the UZIN Product Guide according to surface type and condition or seek technical assistance. Allow primers to dry thoroughly. As with all polymer modified cements, it is always recommended to test for moisture content of the existing substrate to ensure that it meets the floor covering manufacturer’s requirements. Cement based products are not designed to be used as moisture barriers. Moisture mitigation must be addressed prior to the application of UZIN NC 150. Select a suitable UZIN moisture vapor retarder.For solid wood flooring installations use UZIN NC 170 LevelStar.Before applying UZIN NC 150 over plywood / OSB flooring, the use of UZIN RR 201 substrate reinforcing mesh is required on top of the primed surface. UZIN NC 150 must be installed to a minimum 1/4" (6 mm) depth over UZIN RR 201 (please see UZIN RR 201 product data sheet for additional installation instructions). Excessive movement within the subfloor may lead to hairline cracks at plywood joints.For additional information regarding subfloor preparation, please refer to the UZIN “Substrate Preparation Guide”.

Application:1. Pour required amount of cold, clean water into a clean container (refer to

product packaging for water ratio). Slowly pour in the powder whilst stirring vigorously for 60 seconds or until blended to a viscous lump free consistency. Use a heavy-duty drill with the UZIN leveling compound mixer attachment (minimum 650 rpm). Do not overwater.

2. Pour the mix onto the primed substrate and distribute evenly with an UZIN Smoothing Trowel or the UZIN Gauge Rake. For thicker coats or when using a smoothing trowel, flow and surface finish can be improved by using the UZIN Spike Roller. Where possible, apply to the desired depth in one application. A minimum depth of 1/8" (3 mm) is required for exposure to castor wheels and on non absorbent surfaces. When applying over UZIN 1-component polyurethane or 2-component epoxy moisture vapor retarder, always prime surface with UZIN PE 280 or grit bind with sand.

Refer to the floor covering manufacturer regarding the maximum allowable substrate moisture content and qualify the substrate prior to installing UZIN NC 150.

Always install adequate test areas including the finish flooring, to determine the suitability for the intended use. As floor coverings vary, always contact and rely upon the floor covering manufacturer for specific directives, such as maximum allowable moisture content, adhesive selection and intended end use of the product.

NOTE: UZIN NC 150 will accept foot traffic after approx. 2 – 3 hours* and is ready for installation of carpet, resilient and stone coverings after approx. 24 hours up to a depth of 1/4" (6 mm). Ready for installation of ceramic tile after approx. 24 hours* (with a max. depth of 1" / 25 mm).*At 70 °F (21 °C) and 65% relative humidity.

Important Notes:3 Storage: minimum 6 months in original packaging when stored in dry conditions.

Tightly reseal opened packaging and use the contents as quickly as possible.

3 UZIN NC 150 contains Portland Cement. See: “Protection of the Workplace and the Environment”.

3 Optimum application conditions are 60 – 77 °F (16 – 25 °C) and relative humi dity below 65%. Low temperature, high humidity and greater pour depths will delay drying. High temperatures and low humidity will accelerate the setting, drying and readiness for covering. In summer, store in cool conditions and use cold water.

3 Expansion, movement and wall connection joints must be honored through the floor covering. Where necessary, fit UZIN Expansion Strips to any structures to prevent the mix from flowing into connection joints. For depths greater than 1/4" (6 mm) expansion strips are highly recommended.

3 Pumpable using continuous feed mixer pumps.

3 For information regarding sand extension with UZIN NC 150, please call the UZIN Technical Dept.

3 Minimum 1/8" (3 mm) depth is required for exposure to castor wheels.

3 If pouring multiple layers of leveling compound, allow product to completely dry. Apply UZIN PE 260 diluted 1:3 as an intermediate primer between applications. Allow UZIN PE 260 to dry to a clear, transparent, almost tack free film (refer to the UZIN PE 260 product data sheet for dry times). Once primer has dried, apply next layer of UZIN NC 150. Each subsequent layer should not exceed the depth of the previous layer.

3 For depths between 1/4" (6 mm) and 1" (25 mm) on moisture sensitive or weak substrates (old adhesive residues), first apply a suitable UZIN 2-component epoxy moisture vapor retarder gritted with a broadcast of sand.

3 Do not use in exterior or wet areas.

3 On substrates with old cutback adhesive residues, it is recommended to remove as much residue as possible by mechanical means before coating with a suitable UZIN Primer. Call the UZIN Technical Dept. for assistance.

3 NOTE: Complete mechanical removal of cutback adhesive such as shot blasting, grinding or sanding can be hazardous as old adhesive may contain asbestos. Do not sand or grind adhesive residues. Harmful dust may result. Inhalation of asbestos dust may cause asbestosis or other serious bodily harm. Please consult applicable government agencies for rules and regulations concerning removal of flooring or adhesives containing asbestos. The use of solvents or adhesive removers are never recommended.

3 Protect freshly applied leveling compounds from drafts, direct sunlight and direct sources of heat.

3 The following standards, regulations and notices are applicable and especially recommended:

• ASTM F710-11 “Standard Practice for Preparing Concrete Floors To Receive Resilient Flooring”

• ASTM C 109 modified “Test method for compressive strength of hydraulic cement mortars”

• ASTM F1869-11 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride”

• ASTM F2170-11 “Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes”

Protection of the Workplace and the Environment:PRECAUTIONS:CAUTION: Irritant. Contains cement. Keep out of reach of children. Cement produces strong alkaline on reaction with water. Avoid contact with skin and eyes. When mixing wear a protective dust-mask. Use protective gloves and wear safety glasses or goggles.FIRST AID: In case of skin or eye contact, rinse thoroughly and immediately with water. In the event of skin or eye irritation, obtain medical treatment. Observe safety information on product label as well as MATERIAL SAFETY DATA SHEET (MSDS). Presents no physiological or ecological risk when fully cured. EMICODE EC 1 R PLUS – very low emission – healthy indoor air quality.WARNING: This product contains chemicals (crystalline silica) known to the state of California to cause cancer and birth defects, or other reproductive harm .DOT UN-Number: Not regulated Hazard Class /PG: Not regulated

Disposal:Dispose of empty packaging according to local, state and federal regulations. Hardened product residues are considered construction waste. Therefore collect waste material, mix with water and allow to harden, then dispose of as construction waste. Empty paper bags are recyclable.

The above information is based on our experience and testing. UFLOOR Systems is not responsible for the variety of associated materials and variable construction and working conditions that occur on jobsites. The quality of your work depends on your own professional judgment and product usage. If in doubt of any application recommendation or instruction, conduct a small test or obtain technical advice. Observe the installation recommendations of the floor covering manufacturer. The publication of this Product Data Sheet invalidates all previous product information.

All items also sold separately.

UZIN Water Bucket: (2.4 gal.)

Item # 10412

UZIN Spike Roller:Item # 13638

(Only sold separately)

UZIN Smoothing Trowel: Item # 59361

UZIN Telescoping Extension Pole: Item # 12503

UZIN Gauge Rake:Item # 59771

UZIN Oval Mixing Paddle:

Item # 59597

UZIN Mixing Drum: (16 gal.)Item # 59267

UZIN Drum Kit (includes Drum, Rake, Trowel, Bucket, Paddle, and Pole): Item # 59973

Leveling Application Tools:


08

.15

| msl

/8

Safety Data Sheetacc. to OSHA HCS

Printing date 03/31/2015 Reviewed on 03/31/2015Version No. 3

40.0

1 Identification

· Trade name: UZIN NC 150

· Relevant identified uses of the substance or mixture and uses advised againstNo further relevant information available.

· Application of the substance / the mixture Leveling Compound

· Details of the supplier of the safety data sheet· Manufacturer/Supplier:

Manufacturer:

UZIN UTZ AG

Dieselstrasse 3

D-89079 Ulm

Germany

Tel.: +49 (0)731 4097-0

Fax: +49 (0)731 4097-110

Supplier:

UFLOOR Systems Inc.

14509 E. 33rd. Place, Unit G

Aurora, CO 80011

Phone: +720-374-4810

Toll-Free: +1 866-505-4810

Fax: +1 720-374-2113

· Information department:Product safety department

email: [email protected]

· Emergency telephone number:For Chemical Emergency Spill Leak Fire Exposure or Accident

Call CHEMTREC Day or Night: DOMESTIC NORTH AMERICA 800-424-9300

International, call +49 621 60 43 333

* 2 Hazard(s) identification

· Classification of the substance or mixture

GHS05 Corrosion

Eye Dam. 1 H318 Causes serious eye damage.

· Information concerning particular hazards for human and environment:The product has to be labeled due to the calculation procedure of international guidelines.

· Label elements· GHS label elements

The product is classified and labeled according to the Globally Harmonized System (GHS).

· Hazard pictograms GHS05

· Signal word Danger

· Hazard-determining components of labeling:Portland cement

· Hazard statementsCauses serious eye damage.

· Precautionary statementsKeep out of reach of children.

Avoid breathing dust.

Wear protective gloves / eye protection.

If on skin: Wash with plenty of soap and water.

If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.

Continue rinsing.(Contd. on page 2)

USA

/8



Trade name: UZIN NC 150

(Contd. of page 1)

40.0

If eye irritation persists: Get medical advice/attention.

· NFPA ratings (scale 0 - 4)

20

0

Health = 2

Fire = 0

Reactivity = 0

· HMIS-ratings (scale 0 - 4)

HEALTH

FIRE

REACTIVITY

2

0

0

Health = 2

Fire = 0

Reactivity = 0

· Other hazardsNFPA Rating Scale: 0 = Minimal; 1 = Slight; 2 = Moderate; 3 = Serious; 4 = Severe.

NFPA is the National Fire Protection Association.

HMIS Rating Scale: 0 = Minimal; 1 = Slight; 2 = Moderate; 3 = Serious; 4 = Severe.

HMIS®, the Hazardous Materials Identification System, is a registered mark of the National Paint and

Coatings Association (NPCA).

· Results of PBT and vPvB assessment· PBT: Not applicable.

· vPvB: Not applicable.

* 3 Composition/information on ingredients

· Chemical characterization: Mixtures

· Description: Mixture of the substances listed below with nonhazardous additions.

· Dangerous components:

14808-60-7 Quartz (SiO2)

Carc. 1A, H350

25-50%

65997-15-1 Portland cement

Xi R37/38-41

Eye Dam. 1, H318; Skin Irrit. 2, H315; STOT SE 3, H335

5 - <10%

· Additional information:For the wording of the listed risk phrases refer to section 16.

The amount of respirable cristalline silica is less than 0.1 %.

4 First-aid measures

· Description of first aid measures· After inhalation: Supply fresh air; consult doctor in case of complaints.

· After skin contact: Immediately wash with water and soap and rinse thoroughly.

· After eye contact:Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.

· After swallowing: Do not induce vomiting; immediately call for medical help.

· Most important symptoms and effects, both acute and delayed No further relevant information available.

· Indication of any immediate medical attention and special treatment neededNo further relevant information available.

* 5 Fire-fighting measures

· Extinguishing media· Suitable extinguishing agents:

CO₂, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.(Contd. on page 3)

USA

/8




(Contd. of page 2)

40.0

· For safety reasons unsuitable extinguishing agents: Water with full jet

· Special hazards arising from the substance or mixture No further relevant information available.

· Advice for firefighters· Protective equipment: No special measures required.

6 Accidental release measures

· Personal precautions, protective equipment and emergency procedures Wear dust mask.

· Environmental precautions: Do not allow to enter sewers/ surface or ground water.

· Methods and material for containment and cleaning up: Pick up mechanically.

· Reference to other sectionsSee Section 7 for information on safe handling.

See Section 8 for information on personal protection equipment.

See Section 13 for disposal information.

7 Handling and storage

· Precautions for safe handlingPrevent formation of dust.

Wear suitable protective clothing, gloves and eye/face protection.

Avoid contact with the eyes and skin.

Wash hands before breaks and at the end of work.

· Information about protection against explosions and fires: No special measures required.

· Conditions for safe storage, including any incompatibilities· Storage:· Requirements to be met by storerooms and receptacles: No special requirements.

· Information about storage in one common storage facility: Not required.

· Further information about storage conditions:Store in dry conditions.

Protect from humidity and water.

· Specific end use(s) No further relevant information available.

* 8 Exposure controls/personal protection

· Additional information about design of technical systems: No further data; see item 7.

· Control parameters

· Components with limit values that require monitoring at the workplace:

14808-60-7 Quartz (SiO2)

PEL see Quartz listing

REL Long-term value: 0.05* mg/m³

*respirable dust; See Pocket Guide App. A

TLV Long-term value: 0.025* mg/m³

*as respirable fraction


PEL Long-term value: 50 mppcf or 15* 5** mg/m³

*total dust **respirable fraction

REL Long-term value: 10* 5** mg/m³


TLV Long-term value: 1* mg/m³

E; *as respirable fraction

(Contd. on page 4)

USA

/8




(Contd. of page 3)

40.0

· Exposure controls· Personal protective equipment:· General protective and hygienic measures:

Prevent formation of dust.




· Breathing equipment: When mixing wear suitable NIOSH-approved dust respirator.

· Protection of hands:

Use nitrile impregnated cotton-gloves

· Material of gloves Nitrile impregnated cotton-gloves

· Penetration time of glove materialThe exact break trough time has to be found out by the manufacturer of the protective gloves and has to be

observed.

· Eye protection:

Tightly sealed goggles

9 Physical and chemical properties

· Information on basic physical and chemical properties· General Information· Appearance:

Form: Solid

Color: Grey

· Odor: Light

· Odour threshold: Not determined.

· pH-value at 20 °C (68 °F): 11

· Change in conditionMelting point/Melting range: Undetermined.

Boiling point/Boiling range: Undetermined.

· Flash point: Not applicable.

· Flammability (solid, gaseous): Not determined.

· Ignition temperature:

Decomposition temperature: Not determined.

· Auto igniting: Product is not selfigniting.

· Danger of explosion: Product does not present an explosion hazard.

· Explosion limits:Lower: Not determined.

Upper: Not determined.

· Vapor pressure: Not applicable.

· Density: Not determined.

· Relative density Not determined.

· Vapour density Not applicable.

(Contd. on page 5)

USA

/8




(Contd. of page 4)

40.0

· Evaporation rate Not applicable.

· Solubility in / Miscibility withWater: Insoluble.

Sets with water.

· Partition coefficient (n-octanol/water): Not determined.

· Viscosity:Dynamic: Not applicable.

Kinematic: Not applicable.

· Other information No further relevant information available.

10 Stability and reactivity

· Reactivity· Chemical stability· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.

· Possibility of hazardous reactions No dangerous reactions known.

· Conditions to avoid No further relevant information available.

· Incompatible materials: No further relevant information available.

· Hazardous decomposition products: No dangerous decomposition products known.

* 11 Toxicological information

· Information on toxicological effects· Acute toxicity:· Specific symptoms in biological assay:· Primary route(s) of entry: Inhalation, skin contact, eye contact.

· Primary irritant effect:· on the skin: Slightly irritant effect may occur.

· on the eye: Strong irritant with the danger of severe eye injury.

· Sensitization:No sensitizing effects known.

Low in Chromate (< 2 ppm) acc. Regulation (EC) No 1907/2006 (REACH).

· Subacute to chronic toxicity:The amount of respirable cristalline silica is less than 0.1 %.

Respirable crystalline silica (quartz) may cause a severe lung desease named silicosis. Symptoms of silicosis

may be a shortness of breath, fever or cough. Silicosis is reported to increase the risk of carcinogenicity

caused by continuous inhalation of respirable crystalline silica. Though the product itself does not contain

respirable crystalline silica, respirable silica may be generated from working procedures such as grinding

e.g. In general, inhalation of silica dust should be avoided. Therefore, for your own safety wear a suitable

NIOSH-approved respirator in all occasions when handling of the product generates dust.

· Additional toxicological information:The product shows the following dangers according to internally approved calculation methods for

preparations:

Corrosive

· Carcinogenic categories

· IARC (International Agency for Research on Cancer)

14808-60-7 Quartz (SiO2) 1

· NTP (National Toxicology Program)

14808-60-7 Quartz (SiO2) K

(Contd. on page 6)

USA

/8




(Contd. of page 5)

40.0

· OSHA-Ca (Occupational Safety & Health Administration)

None of the ingredients is listed.

12 Ecological information

· Toxicity· Aquatic toxicity: No further relevant information available.

· Persistence and degradability No further relevant information available.

· Bioaccumulative potential No further relevant information available.

· Mobility in soil No further relevant information available.

· Additional ecological information:· General notes: Do not allow product to reach ground water, water course or sewage system.



· Other adverse effects No further relevant information available.

13 Disposal considerations

· Waste treatment methods· Recommendation:

Do not allow product to reach sewage system.

Mix product residues with water, allow to harden, then dispose of as construction waste.

· Uncleaned packagings:· Recommendation: Empty paper packaging is recyclable.

14 Transport information

· DOT, ADR, ADN, IMDG, IATA Void

· UN proper shipping name· DOT, ADR, ADN, IMDG, IATA Void

· DOT, ADN, IMDG, IATA· Class Void

· DOT, IMDG, IATA Void

· Environmental hazards:· Marine pollutant: No

· Special precautions for user Not applicable.

· Transport/Additional information: Not regulated as hazardous material according to the above

specifications.

· UN "Model Regulation": -

* 15 Regulatory information

· Safety, health and environmental regulations/legislation specific for the substance or mixture· SARA (Superfund Amendments and Reauthorization Act)

· Section 355 (extremely hazardous substances):

None of the ingredient is listed.

(Contd. on page 7)

USA

/8




(Contd. of page 6)

40.0

· Section 313 (Specific toxic chemical listings):


· TSCA (Toxic Substances Control Act):

All ingredients are listed.

· Proposition 65 (California)

· Chemicals known to cause cancer:

14808-60-7 Quartz (SiO2)

· Chemicals known to cause reproductive toxicity for females:


· Chemicals known to cause reproductive toxicity for males:


· Chemicals known to cause developmental toxicity:


· Cancerogenity categories

· EPA (Environmental Protection Agency)


· TLV (Threshold Limit Value established by ACGIH)

14808-60-7 Quartz (SiO2) A2

· NIOSH-Ca (National Institute for Occupational Safety and Health)

14808-60-7 Quartz (SiO2)

· GHS label elementsThe product is classified and labeled according to the Globally Harmonized System (GHS).










Continue rinsing.


16 Other information

This information is based on our present knowledge. However, this shall not constitute a guarantee for any

specific product features and shall not establish a legally valid contractual relationship.

· Department issuing SDS: Product safety department

· Contact:USA: Daniel Gill, phone + 1 720-374-4810

Germany: Dr. Zieger, phone +49 731.409.7207

· Date of preparation / last revision 03/31/2015 / 2

· Abbreviations and acronyms:RID: Règlement international concernant le transport des marchandises dangereuses par chemin de fer (Regulations Concerning the

International Transport of Dangerous Goods by Rail)

ICAO: International Civil Aviation Organisation

(Contd. on page 8)

USA

/8




(Contd. of page 7)

40.0

ADR: Accord européen sur le transport des marchandises dangereuses par Route (European Agreement concerning the International

Carriage of Dangerous Goods by Road)

IMDG: International Maritime Code for Dangerous Goods

DOT: US Department of Transportation

IATA: International Air Transport Association

ACGIH: American Conference of Governmental Industrial Hygienists

EINECS: European Inventory of Existing Commercial Chemical Substances

ELINCS: European List of Notified Chemical Substances

CAS: Chemical Abstracts Service (division of the American Chemical Society)

NFPA: National Fire Protection Association (USA)

HMIS: Hazardous Materials Identification System (USA)

Skin Irrit. 2: Skin corrosion/irritation, Hazard Category 2

Eye Dam. 1: Serious eye damage/eye irritation, Hazard Category 1

Carc. 1A: Carcinogenicity, Hazard Category 1A

STOT SE 3: Specific target organ toxicity - Single exposure, Hazard Category 3

· * Data compared to the previous version altered. USA

Use of US Green Building Council Member logo does not imply that USGBC has approved this confirmation or any mentioned product. Use of that logo just states that Eurofins Product Testing A/S is member of US Green Building Council.

Eurofins Product Testing A/S Smedeskovvej 38 DK 8464 Galten / Denmark

Tel +45 70 22 42 76 Fax +45 70 22 42 75

www.product-testing.eurofins.com

CCoonnffiirrmmaattiioonn Eurofins Product Testing A/S confirms that a sample of a cement based leveling compound with the name

UUZZIINN NNCC 115500 supplied by

UUzziinn UUttzz AAGG showed low VOC emissions in a test in accordance with the “Standard Method for the Testing and Evaluation of VOC Emissions from Indoor Sources using Environmental Chambers, version 1.1 of February 2010 by the California Department of Public Health”, as specified in indoor air emission criteria of Collaborative for High Performance Schools (CHPS), Indoor Advantage Gold TN certification, Floorscore and LEED credit 4.3 (flooring systems). Emissions were below all limit values specified in that standard practice. The test has been performed in November 2013, see test report no. 392-2013-00081201. The testing methodology is covered by independent ISO 17025 accreditation, issued by DANAK (# 522). With this confirmation, use of product may qualify for fulfillment of LEED credit IEQ 4.3 (flooring systems).

11 December 2013

_____________________ Pascal Ge Analytical Service Manager

UZIN NC 170 LevelStarSelf-drying cementitious leveling compound. Provides extremely smooth fi nish without depth limitations.

Premium Self Leveling Compound

Description:Premium low stress, self leveling underlayment and smoothing compound for all types of interior floor covering work. May be used as a topping provided a suitable wear surface sealer or coating is applied. For interior use only.

Suitable for/on: 3 Producing level, absorbent, fl at and smooth surfaces for virtually all types

of fl oor coverings including wood, carpet, sheet vinyl, VCT, PVC, linoleum, cork, rubber, polyolefi n, ceramic tile and natural stone

3 A smoothing layer over structurally sound concrete above, on or below grade, in new construction or renovation projects. May be used over cast in place or precast concrete

3 A smoothing layer over existing hard surface fl ooring such as well bonded terrazzo, ceramic tile, stone and well bonded epoxy coatings

3 New, structurally sound, OSB underlayment or equally rated subfl oor materials

3 Existing substrates, including thin and dense non water soluble adhesive residues on concrete including cutback adhesive residues (see “Important Notes”)

3 High stress loads in residential, commercial and industrial locations, such as hospitals, shopping centers and industrial facilities

3 Radiant fl oor heating systems, (hydronic or electric)

Product Properties:Highly modifi ed polymer premium leveling compound with special raw material technology known as the Level Plus Effect. The Level Plus Effect with super condensers provides exceptional fl ow characteristics and a very smooth, uniform surface appearance promoting an increased adhesive coverage rate. The special advantage of UZIN NC 170 LevelStar is the ideal combination of multipurpose use, the best application properties, highest strength development and load bearing capacity.UZIN ÖkoLine® is a system of tested and approved installation materials based on the principles of neutral odor and clean indoor air (see “Protection of the Workplace and the Environment”).

Composition: Special cements, mineral fi llers, polyvinyl acetate copoly mers, fl ow agents and additives.

Features• Level Plus Effect• No depth limitation• Pumpable• Fast setting• Very smooth surface• Low stress• Shear resistant under wood

fl ooring• Very high compressive and

tensile strengths• Exceptionally fi ne

aggregates• Signifi cantly longer

working time• Meets strict EMICODE

EC 1 R PLUS criteria• Compliant with California

Sect. 01350 specifi cation

Benefi ts• Superior fl ow characteristics• Very versatile• Minimizes time and effort• Accelerates fl oor covering installation• Improves adhesive coverage rate• Ability to cover diffi cult substrates• Suitable for all glue down wood applications

• Exceeds most fl ooring requirements for suitable surface

• Allows NC 170 LevelStar to obtain a true feather edge and can be used as a skim coat

• Greater jobsite fl exibility

• Healthy indoor air quality

• LEED V4 contributing product

Technical DataPackaging: 50 lb. (22.7 kg) paper bag

Storage: minimum 6 months

Water ratio: refer to product packaging

Color: grey

Coverage rate: 30 sq. ft. at 1/4" depth per 50 lb. bag(approx.) (2.78 m² at 6 mm depth per 22.7 kg bag)

actual coverage may vary depending on substrate conditions

Working temperature: min. 60 °F (16 °C) at fl oor level

Working time: 20 – 30 minutes*

Set to foot traffi c: after approx. 2 hours*

Ready for covering: after approx. 15 hours*

Compressive strength 5300 psi after 28 days (ASTM C109M-12)

Flexural strength 1100 psi after 28 days (ASTM C348-08)

* At 70 °F (21 °C) and 65% relative humidity. Depth of application and surface porosity will affect dry time.


Part of Uzin Primary“Decks Covering”


LEED®

contributingproduct

UZIN NC 170 LevelStar

Substrate Preparation:The subfloor must be structurally sound, solid, dry, free from active cracks, clean and free of all contaminants such as grease, oil, paint, wax, curing and sealing compounds that would impair adhesion. Test the substrate in accordance with applicable standards relative to moisture content. Any weakly bonded or soft surface material such as loose adhesive residues, leveling compounds, floor coverings or coatings must be removed by shot blasting, abrading, grinding or wet scraping. Thoroughly vacuum off all loose material or dust. CAUTION: Do not sand or grind adhesive residue, as harmful dust may result. Inhalation of asbestos dust may cause asbestosis or other serious bodily harm. Refer to the Resilient Floor Covering Institute’s publication “Recommended Work Practices for Removal of Resilient Floor Coverings” for instructions. Select a suitable primer from the UZIN Product Guide according to surface type and condition or seek technical assistance. Allow primers to dry thoroughly. As with all polymer modified cements, it is always recommended to test for moisture content of the existing substrate to ensure that it meets the floor covering manufacturer’s requirements. Cement based products are not designed to be used as moisture barriers. Moisture mitigation must be addressed prior to the application of UZIN NC 170. Select a suitable UZIN moisture vapor retarder.

Before applying UZIN NC 170 over plywood / OSB flooring, the use of UZIN RR 201 substrate reinforcing mesh is required on top of the primed surface. UZIN NC 170 must be installed to a minimum 1/4" (6 mm) depth over UZIN RR 201 (please see UZIN RR 201 product data sheet for additional installation instructions). Excessive movement within the subfloor may lead to hairline cracks at plywood joints.

For additional information regarding subfloor preparation, please refer to the UZIN “Substrate Preparation Guide”.

Application:1. Pour required amount of cold, clean water into a clean container

(refer to product packaging for water ratio). Slowly pour in the powder whilst stirring vigorously for 60 seconds or until blended to a viscous lump free consistency. Use a heavy-duty drill with the UZIN leveling compound mixer attachment (minimum 650 rpm). Do not overwater.

2. Pour the mix onto the primed substrate and distribute evenly with an UZIN Smoothing Trowel or the UZIN Gauge Rake. For thicker coats or when using a smoothing trowel, flow and surface finish can be improved by using the UZIN Spike Roller. Where possible, apply to the desired depth in one application. A minimum depth of 1/8" (3 mm) is required for exposure to castor wheels and on non absorbent surfaces. When applying over UZIN 1-component polyurethane or 2-component epoxy moisture vapor retarder, always prime surface with UZIN PE 280 or grit bind with sand.

Refer to the floor covering manufacturer regarding the maximum allowable substrate moisture content and qualify the substrate prior to installing UZIN NC 170 LevelStar.

Always install adequate test areas including the finish flooring, to determine the suitability for the intended use. As floor coverings vary, always contact and rely upon the floor covering manufacturer for specific directives, such as maximum allowable moisture content, adhesive selection and intended end use of the product.

Important Notes:3 Storage: minimum 6 months in original packaging when stored in dry conditions.

Tightly reseal opened packaging and use the contents as quickly as possible.3 UZIN NC 170 LevelStar contains Portland Cement. See: “Protection of the Workplace

and the Environment”.3 Optimum application conditions are 60 – 77 °F (16 – 25 °C) and relative humidity

below 65 %. Low temperatures, high humidity and greater depth will delay, while high temperatures and low humidity will accelerate the setting, drying and readiness for installation of finish floor covering. In summer, store in cool conditions and mix with cold water.

3 Expansion, movement and wall connection joints must be honored through the floor covering. Where necessary, fit UZIN Expansion Strips to any structures to prevent the mix from flowing into connection joints. For depths greater than 1/4" (6 mm) expansion strips are highly recommended.

3 Pumpable using continuous feed mixer pumps.3 For information regarding sand extension with UZIN NC 170 LevelStar, please call

the UZIN Technical Dept.3 Minimum 1/8" (3 mm) depth is required for exposure to castor wheels. 3 If pouring multiple layers of leveling compound, allow product to completely dry.

Apply UZIN PE 260 diluted 1 : 3 as an intermediate primer between applications. Allow UZIN PE 260 to dry to a clear, transparent, almost tack free film (refer to the UZIN PE 260 product data sheet for dry times). Once primer has dried, apply next layer of UZIN NC 170 LevelStar. Each subsequent layer should not exceed the depth of the previous layer.

3 For depths greater than 1/2" (12.5 mm) on surfaces that are moisture sensitive or weak (old adhesive residues), first apply a suitable UZIN 2-component epoxy moisture vapor retarder gritted with a broadcast of sand.

3 Do not use in exterior or wet areas.3 On substrates with old cutback adhesive residues, it is recommended to remove

as much residue as possible by mechanical means before coating with an UZIN Primer. Call the UZIN Technical Dept. for assistance.

3 NOTE: Complete mechanical removal of cutback adhesive such as shot blasting, grinding or sanding can be hazardous as old adhesive may contain asbestos. Do not sand or grind adhesive residues. Harmful dust may result. Inhalation of asbestos dust may cause asbestosis or other serious bodily harm. Please consult applicable government agencies for rules and regulations concerning removal of flooring or adhesives containing asbestos. The use of solvents or adhesive removers are never recommended.

3 Protect freshly applied leveling compounds from drafts, direct sunlight and direct sources of heat.

3 The following standards, regulations and notices are applicable and especially recommended:

• ASTM F710-11 “Standard Practice for Preparing Concrete Floors To Receive Resilient Flooring”.

• ASTM C109M-12 “Test method for compressive strength of hydraulic cement mortars”

• ASTM F1869-11 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride”

• ASTM F2170-11 “Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes”

Protection of the Workplace and the Environment: PRECAUTIONS:CAUTION: Irritant. Contains cement. Keep out of reach of children. Cement produces strong alkaline on reaction with water. Avoid contact with skin and eyes. When mixing wear a protective dust-mask. Use protective gloves and wear safety glasses or goggles .

FIRST AID: In case of skin or eye contact, rinse thoroughly and immediately with water. In the event of skin or eye irritation, obtain medical treatment. Observe safety information on product label as well as MATERIAL SAFETY DATA SHEET (MSDS). Presents no physiological or ecological risk when fully cured. EMICODE EC 1 R PLUS – very low emission – healthy indoor air quality.

WARNING: This product contains chemicals (crystalline silica) known to the state of California to cause cancer and birth defects, or other reproductive harm .

DOT UN-Number: Not regulated Hazard Class /PG: Not regulated

Disposal:Dispose of empty packaging according to local, state and federal regulations. Hardened pro duct residues are considered construction waste. Therefore collect waste material, mix with water and allow to harden, then dispose of as construction waste. Empty paper bags are recyclable.

The above information is based on our experience and testing. UFLOOR Systems is not responsible for the variety of associated materials and variable construction and working conditions that occur on jobsites. The quality of your work depends on your own professional judgment and product usage. If in doubt of any application recommendation or instruction, conduct a small test or obtain technical advice. Observe the installation recommendations of the floor covering manufacturer. The publication of this Product Data Sheet invalidates all previous product information.


08

.15

| msl

All items also sold separately.

UZIN Water Bucket: (2.4 gal.)

Item # 10412

UZIN Spike Roller:Item # 13638

(Only sold separately)

UZIN Smoothing Trowel: Item # 59361

UZIN Telescoping Extension Pole: Item # 12503

UZIN Gauge Rake:Item # 59771

UZIN Oval Mixing Paddle:

Item # 59597

UZIN Mixing Drum: (16 gal.)Item # 59267

UZIN Drum Kit (includes Drum, Rake, Trowel, Bucket, Paddle, and Pole): Item # 59973

Leveling Application Tools:

/8



40.0

1 Identification

· Trade name: UZIN NC 170 LevelStar

· Relevant identified uses of the substance or mixture and uses advised againstNo further relevant information available.

· Application of the substance / the mixture Levelling Compound

· Details of the supplier of the safety data sheet· Manufacturer/Supplier:

Manufacturer:

UZIN UTZ AG

Dieselstrasse 3

D-89079 Ulm

Germany

Tel.: +49 (0)731 4097-0

Fax: +49 (0)731 4097-110

Supplier:

UFLOOR Systems Inc.

14509 E. 33rd. Place, Unit G

Aurora, CO 80011

Phone: +720-374-4810

Toll-Free: +1 866-505-4810

Fax: +1 720-374-2113

· Information department:Product safety department

email: [email protected]

· Emergency telephone number:For Chemical Emergency Spill Leak Fire Exposure or Accident

Call CHEMTREC Day or Night: DOMESTIC NORTH AMERICA 800-424-9300

International, call +49 621 60 43 333

* 2 Hazard(s) identification

· Classification of the substance or mixture

GHS05 Corrosion

Eye Dam. 1 H318 Causes serious eye damage.

· Information concerning particular hazards for human and environment:The product has to be labeled due to the calculation procedure of international guidelines.

· Label elements· GHS label elements

The product is classified and labeled according to the Globally Harmonized System (GHS).










Continue rinsing.(Contd. on page 2)

USA

/8



Trade name: UZIN NC 170 LevelStar

(Contd. of page 1)

40.0


· NFPA ratings (scale 0 - 4)

20

0

Health = 2

Fire = 0

Reactivity = 0

· HMIS-ratings (scale 0 - 4)

HEALTH

FIRE

REACTIVITY

2

0

0

Health = 2

Fire = 0

Reactivity = 0

· Other hazardsNFPA Rating Scale: 0 = Minimal; 1 = Slight; 2 = Moderate; 3 = Serious; 4 = Severe.

NFPA is the National Fire Protection Association.

HMIS Rating Scale: 0 = Minimal; 1 = Slight; 2 = Moderate; 3 = Serious; 4 = Severe.

HMIS®, the Hazardous Materials Identification System, is a registered mark of the National Paint and

Coatings Association (NPCA).



* 3 Composition/information on ingredients

· Chemical characterization: Mixtures

· Description: Mixture of the substances listed below with nonhazardous additions.

· Dangerous components:

14808-60-7 Quartz (SiO2)

Carc. 1A, H350

25-50%


Xi R37/38-41

Eye Dam. 1, H318; Skin Irrit. 2, H315; STOT SE 3, H335

5 - <10%

· Additional information:For the wording of the listed risk phrases refer to section 16.

The amount of respirable cristalline silica is less than 0.1 %.

* 4 First-aid measures

· Description of first aid measures· After inhalation: Supply fresh air; consult doctor in case of complaints.

· After skin contact: Immediately wash with water and soap and rinse thoroughly.

· After eye contact: Rinse opened eye for several minutes under running water. Then consult a doctor.

· After swallowing: Do not induce vomiting; immediately call for medical help.

· Most important symptoms and effects, both acute and delayed No further relevant information available.

· Indication of any immediate medical attention and special treatment neededNo further relevant information available.

* 5 Fire-fighting measures

· Extinguishing media· Suitable extinguishing agents:

CO₂, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.

· For safety reasons unsuitable extinguishing agents: Water with full jet(Contd. on page 3)

USA

/8




(Contd. of page 2)

40.0

· Special hazards arising from the substance or mixture No further relevant information available.

· Advice for firefighters· Protective equipment: No special measures required.

* 6 Accidental release measures

· Personal precautions, protective equipment and emergency procedures Wear dust mask.

· Environmental precautions: Do not allow to enter sewers/ surface or ground water.

· Methods and material for containment and cleaning up: Pick up mechanically.

· Reference to other sectionsSee Section 7 for information on safe handling.

See Section 8 for information on personal protection equipment.

See Section 13 for disposal information.

* 7 Handling and storage

· Precautions for safe handlingPrevent formation of dust.


Keep away from foodstuffs, beverages and feed.



· Information about protection against explosions and fires: No special measures required.

· Conditions for safe storage, including any incompatibilities· Storage:· Requirements to be met by storerooms and receptacles: No special requirements.

· Information about storage in one common storage facility: Not required.

· Further information about storage conditions:Store in dry conditions.

Protect from humidity and water.

· Specific end use(s) No further relevant information available.

* 8 Exposure controls/personal protection

· Additional information about design of technical systems: No further data; see item 7.

· Control parameters

· Components with limit values that require monitoring at the workplace:

14808-60-7 Quartz (SiO2)

PEL see Quartz listing

REL Long-term value: 0.05* mg/m³

*respirable dust; See Pocket Guide App. A

TLV Long-term value: 0.025* mg/m³

*as respirable fraction


PEL Long-term value: 50 mppcf or 15* 5** mg/m³


REL Long-term value: 10* 5** mg/m³


TLV Long-term value: 1* mg/m³

E; *as respirable fraction

(Contd. on page 4)

USA

/8




(Contd. of page 3)

40.0

· Exposure controls· Personal protective equipment:· General protective and hygienic measures:

Prevent formation of dust.


Keep away from foodstuffs, beverages and feed.



· Breathing equipment:Not required.

When mixing wear suitable NIOSH-approved dust respirator.

· Protection of hands:

Use nitrile impregnated cotton-gloves

· Material of gloves Nitrile impregnated cotton-gloves

· Penetration time of glove materialThe exact break trough time has to be found out by the manufacturer of the protective gloves and has to be

observed.

· Eye protection: Safety glasses

9 Physical and chemical properties

· Information on basic physical and chemical properties· General Information· Appearance:

Form: Solid

Color: Grey

· Odor: Light

· Odour threshold: Not determined.

· pH-value at 20 °C (68 °F): 11

· Change in conditionMelting point/Melting range: Undetermined.

Boiling point/Boiling range: Undetermined.

· Flash point: Not applicable.

· Flammability (solid, gaseous): Not determined.

· Ignition temperature:

Decomposition temperature: Not determined.

· Auto igniting: Product is not selfigniting.

· Danger of explosion: Product does not present an explosion hazard.

· Explosion limits:Lower: Not determined.

Upper: Not determined.

· Vapor pressure: Not applicable.

· Density: Not determined.

· Relative density Not determined.

· Vapour density Not applicable.

· Evaporation rate Not applicable.

(Contd. on page 5)

USA

/8




(Contd. of page 4)

40.0

· Solubility in / Miscibility withWater: Insoluble.

Sets with water.

· Partition coefficient (n-octanol/water): Not determined.

· Viscosity:Dynamic: Not applicable.

Kinematic: Not applicable.

· Other information No further relevant information available.

* 10 Stability and reactivity

· Reactivity· Chemical stability· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.

· Possibility of hazardous reactions No dangerous reactions known.

· Conditions to avoid No further relevant information available.

· Incompatible materials: No further relevant information available.

· Hazardous decomposition products: No dangerous decomposition products known.

* 11 Toxicological information

· Information on toxicological effects· Acute toxicity:· Specific symptoms in biological assay:· Primary route(s) of entry: Inhalation, skin contact, eye contact.

· Primary irritant effect:· on the skin: Slightly irritant effect may occur.

· on the eye: Strong irritant with the danger of severe eye injury.

· Sensitization:No sensitizing effects known.

Low in Chromate (< 2 ppm) acc. Regulation (EC) No 1907/2006 (REACH).

· Subacute to chronic toxicity:The amount of respirable cristalline silica is less than 0.1 %.

Respirable crystalline silica (quartz) may cause a severe lung desease named silicosis. Symptoms of silicosis

may be a shortness of breath, fever or cough. Silicosis is reported to increase the risk of carcinogenicity

caused by continuous inhalation of respirable crystalline silica. Though the product itself does not contain

respirable crystalline silica, respirable silica may be generated from working procedures such as grinding

e.g. In general, inhalation of silica dust should be avoided. Therefore, for your own safety wear a suitable

NIOSH-approved respirator in all occasions when handling of the product generates dust.

· Additional toxicological information:The product shows the following dangers according to internally approved calculation methods for

preparations:

Corrosive

· Carcinogenic categories

· IARC (International Agency for Research on Cancer)

14808-60-7 Quartz (SiO2) 1

· NTP (National Toxicology Program)

14808-60-7 Quartz (SiO2) K

(Contd. on page 6)

USA

/8




(Contd. of page 5)

40.0

· OSHA-Ca (Occupational Safety & Health Administration)


* 12 Ecological information

· Toxicity· Aquatic toxicity: No further relevant information available.

· Persistence and degradability No further relevant information available.

· Bioaccumulative potential No further relevant information available.

· Mobility in soil No further relevant information available.

· Additional ecological information:· General notes: Do not allow product to reach ground water, water course or sewage system.



· Other adverse effects No further relevant information available.

* 13 Disposal considerations

· Waste treatment methods· Recommendation:

Do not allow product to reach sewage system.

Mix product residues with water, allow to harden, then dispose of as construction waste.

· Uncleaned packagings:· Recommendation: Empty paper packaging is recyclable.

* 14 Transport information

· DOT, ADR, ADN, IMDG, IATA Void

· UN proper shipping name· DOT, ADR, ADN, IMDG, IATA Void

· DOT, ADN, IMDG, IATA· Class Void

· DOT, IMDG, IATA Void

· Environmental hazards:· Marine pollutant: No

· Special precautions for user Not applicable.

· Transport/Additional information: Not regulated as hazardous material according to the above

specifications.

· UN "Model Regulation": -

* 15 Regulatory information

· Safety, health and environmental regulations/legislation specific for the substance or mixture· SARA (Superfund Amendments and Reauthorization Act)

· Section 355 (extremely hazardous substances):

None of the ingredient is listed.

(Contd. on page 7)

USA

/8




(Contd. of page 6)

40.0

· Section 313 (Specific toxic chemical listings):


· TSCA (Toxic Substances Control Act):

All ingredients are listed.

· Proposition 65 (California)

· Chemicals known to cause cancer:

14808-60-7 Quartz (SiO2)

· Chemicals known to cause reproductive toxicity for females:


· Chemicals known to cause reproductive toxicity for males:


· Chemicals known to cause developmental toxicity:


· Cancerogenity categories

· EPA (Environmental Protection Agency)


· TLV (Threshold Limit Value established by ACGIH)

14808-60-7 Quartz (SiO2) A2

· NIOSH-Ca (National Institute for Occupational Safety and Health)

14808-60-7 Quartz (SiO2)

· GHS label elementsThe product is classified and labeled according to the Globally Harmonized System (GHS).










Continue rinsing.


* 16 Other information

This information is based on our present knowledge. However, this shall not constitute a guarantee for any

specific product features and shall not establish a legally valid contractual relationship.

· Department issuing SDS: Product safety department

· Contact:USA: Daniel Gill, phone + 1 720-374-4810

Germany: Dr. Zieger, phone +49 731.409.7207

· Date of preparation / last revision 03/31/2015 / 3

· Abbreviations and acronyms:RID: Règlement international concernant le transport des marchandises dangereuses par chemin de fer (Regulations Concerning the

International Transport of Dangerous Goods by Rail)

ICAO: International Civil Aviation Organisation

(Contd. on page 8)

USA

/8




(Contd. of page 7)

40.0

ADR: Accord européen sur le transport des marchandises dangereuses par Route (European Agreement concerning the International

Carriage of Dangerous Goods by Road)

IMDG: International Maritime Code for Dangerous Goods

DOT: US Department of Transportation

IATA: International Air Transport Association

ACGIH: American Conference of Governmental Industrial Hygienists

EINECS: European Inventory of Existing Commercial Chemical Substances

ELINCS: European List of Notified Chemical Substances

CAS: Chemical Abstracts Service (division of the American Chemical Society)

NFPA: National Fire Protection Association (USA)

HMIS: Hazardous Materials Identification System (USA)

Skin Irrit. 2: Skin corrosion/irritation, Hazard Category 2

Eye Dam. 1: Serious eye damage/eye irritation, Hazard Category 1

Carc. 1A: Carcinogenicity, Hazard Category 1A

STOT SE 3: Specific target organ toxicity - Single exposure, Hazard Category 3

· * Data compared to the previous version altered. USA


Cementitious leveling and smoothing compounds for all applications.

THE WORLD IS FLAT.

Level Plus

Effect Level Plus

Effect

Item # 55837 Item # 7269155 lb. (25 kg) 50 lb. (22.7 kg)

● Ready for covering in as little as 1 hour● Very smooth surface – increased adhesive coverage rate● Exceptional flow properties ● Very high strength and low stress● Pumpable● Very low emissions / EMICODE EC 1 R PLUS

Premium Plus

UZIN NC 172 BiTurboExceptionaly fast drying, smooth finish with no depth limitation

Premium

UZIN NC 170 LevelStarExtremely smooth finish without depth limitations

● Fast setting● Suitable for all types of floor coverings● Exceptionally fine aggregates● Significantly longer working time● Very low emissions / EMICODE EC 1 R PLUS

YOUR FLOORS DESERVE THE BEST.

Item # 72690 Item # 7253650 lb. (22.7 kg) 50 lb. (22.7 kg)

● For depths up to 1"● Quick drying● Low stress – ability to cover difficult substrates● Very low emissions / EMICODE EC 1 R PLUS

● High coverage● For depths up to 2"● Very low emissions / EMICODE EC 1 R PLUS

Project Plus

UZIN NC 150Smooth finish for resilient floor coverings

Project

UZIN NC 157Economical surface preparation

The flooring industry is constantly changing and at UZIN we are leading the way by developing products that adapt to those changes.With over 100 years experience, we have earned an outstanding reputation for innovative product development and technical expertise but more importantly by listening to you, our customers.On every project you face, we will be there with you, offering you the right solutions and the highest technical support to ensure that you meet your requirements.UZIN. YOUR FLOOR. OUR PROMISE.

Level Plus

Effect

“ The UZIN products are formulated to set us up for success and their technical and field support enhances the professional execution of each project.” Sheila McGovern, Cavalier Flooring Systems

UZIN | A brand of UFLOOR Systems Inc. | 14509 E. 33rd Place, Unit G | Aurora, CO 80011 | USAPhone +1 720 374 4810 | Fax +1 720 374 2113 | [email protected] | www.uzin.us

PROVEN UZIN QUALITY.

● Reduced adhesive consumption ● Uniform surface appearance● Significantly reduces preparation costs

09.2014 | MSL

LEVEL PLUS EFFECT:

READY FOR COVERING

30

25

20

15

10

5

HRS NC 157 NC 150 NC 170 NC 172FLEXURAL STRENGTH*

*AFTER 28 DAYS2000

1500

1000

500

PSI NC 157 NC 150 NC 170 NC 172COMPRESSIVE STRENGTH*

*AFTER 28 DAYS8000

7000

6000

5000

4000

3000

2000

1000

PSI NC 157 NC 150 NC 170 NC 172COVERAGE RATE*

*AT ¼" DEPTH35

30

25

20

15

10

5

FT2 NC 157 NC 150 NC 170 NC 172● Extremely smooth surface ● Outstanding flow properties ● Excellent and increased absorption

UZIN NC 150 - Montclair State University · Project Plus Self Leveling Compound ... adhesive...

Documents

Transcript of UZIN NC 150 - Montclair State University · Project Plus Self Leveling Compound ... adhesive...