USER’S GUIDE GUÍA DEL USUARIO - Support | Home …USER’S GUIDE GUÍA DEL USUARIO 662A-E-002A...
40
LK100ES1A ES USER’S GUIDE GUÍA DEL USUARIO
Transcript of USER’S GUIDE GUÍA DEL USUARIO - Support | Home …USER’S GUIDE GUÍA DEL USUARIO 662A-E-002A...
LK100ES1A
ES
USER’S GUIDEGUÍA DEL USUARIO
662A-E-002A
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas).
NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment.
Important!Please note the following important information before using this product.
• Before using the optional AD-5 Adaptor to power the unit, be sure to check the AC Adaptorfor any damage first. Carefully check the power cord for breakage, cuts, exposed wire andother serious damage. Never let children use an AC adaptor that is seriously damaged.
• Never attempt to recharge batteries.• Do not use rechargeable batteries.• Never mix old batteries with new ones.• Use recommended batteries or equivalent types.• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated
near the battery compartment.• Replace batteries as soon as possible after any sign they are getting weak.• Do not short-circuit the battery terminals.• The product is not intended for children under 3 years.• Use only CASIO AD-5 adaptor.• The AC adaptor is not a toy.• Be sure to disconnect the AC adaptor before cleaning the product.
CASIO Europe GmbHBornbarch 10, 22848 Norderstedt, Germany
This mark applies in EU countries only.
E-1
Safety Precautions
Congratulations on your selection of theCASIO electronic musical instrument.• Before using the instrument, be sure to
carefully read through the instructionscontained in this manual.
• Be sure to keep all user documentationhandy for future reference.
SymbolsVarious symbols are used in this user’s guideand on the product itself to ensure that theproduct is used safely and correctly, and toprevent injury to the user and other personsas well as damage to property. Thosesymbols along with their meanings areshown below.
DANGER
This symbol indicates information that, ifignored or applied incorrectly, creates thedanger of death or serious personal injury.
WARNING
This indication stipulates matters that havethe risk of causing death or serious injuryif the product is operated incorrectly whileignoring this indication.
CAUTION
This indication stipulates matters that havethe risk of causing injury as well as mattersfor which there is the likelihood ofoccurrence of physical damage only if theproduct is operated incorrectly whileignoring this indication.
Symbol Examples
This triangle symbol ( ) meansthat the user should be careful.(The example at left indicateselectrical shock caution.)
This circle with a line through it( ) means that the indicatedaction must not be performed.Indications within or nearby thissymbol are specificallyprohibited. (The example at leftindicates that disassembly isprohibited.)
The black dot ( ) means that theindicated action must beperformed. Indications withinthis symbol are actions that arespecifically instructed to beperformed. (The example at leftindicates that the power plug mustbe unplugged from the electricalsocket.)
662A-E-003A
E-2 662A-E-004A
Misuse of the AC adaptor’selectric cord can damage or breakit, creating the risk of fire andelectric shock. Always make sureyou observe the followingprecautions.• Never place heavy objects on
the cord or subject it to heat.• Never try to modify the cord
or subject it to excessivebending.
• Never twist or stretch the cord.• Should the electric cord or plug
become damaged, contact youroriginal retailer or authorizedCASIO Service Provider.
Never touch the AC adaptorwhile your hands are wet.Doing so creates the risk ofelectric shock.• Use the AC adaptor where it
will not be splashed with water.Water creates the risk of fireand electric shock.
• Do not place a vase or any othercontainer filled with liquid ontop of the AC adaptor. Watercreates the risk of fire andelectric shock.
BatteriesMisuse of batteries can cause themto leak, resulting in damage tonearby objects, or to explode,creating the risk of fire and personalinjury. Always make sure youobserve the following precautions.• Never try to take batteries apart
or allow them to become shorted.• Never expose batteries to heat or
dispose of them by incineration.• Never mix old batteries with new
ones.• Never mix batteries of different
types.• Do not charge the batteries.• Make sure the positive (+) and
negative (–) ends of the batteriesare facing correctly.
DANGER
Alkaline BatteriesPerform the following stepsimmediately if fluid leaking fromalkaline batteries ever gets into youreyes.1. Do not rub your eyes! Rinse them
with water.2. Contact your physician
immediately.Leaving alkaline battery fluid inyour eyes can lead to loss of sight.
WARNING
Smoke, Strange Odor, OverheatingContinued use of the product whileit is emitting smoke, a strange odor,or heat creates the risk of fire andelectric shock. Take the followingsteps immediately.1. Turn off power.2. If you are using the AC adaptor
for power, unplug it from the walloutlet.
3. Contact your original retailer oran authorized CASIO ServiceProvider.
AC Adaptor Misuse of the AC adaptor creates
the risk of fire and electric shock.Always make sure you observethe following precautions.• Be sure to use only the AC
adaptor that is specified for thisproduct.
• Use only a power source whosevoltage is within the ratingmarked on the AC adaptor.
• Do not overload electricaloutlets and extension cords.
E-3
Plastic BagsNever place the plastic bag theproduct comes in over your head orin your mouth. Doing so creates therisk of suffocation.Particular care concerning thisprecaution is required where smallchildren are present.
Keep off of the product and stand.*Climbing onto the product or standcan cause it to tip over or becomedamaged. Particular careconcerning this precaution isrequired where small children arepresent.
LocationAvoid locating the product on anunstable stand, on an unevensurface, or any other unstablelocation. An unstable location cancause the product to fall over,creating the risk of personal injury.
Do not incinerate the product.Never throw the product into fire.Doing so can cause it to explode,creating the risk of fire and personalinjury.
Water and Foreign MatterWater, other liquids, and foreignmatter (such as pieces of metal)getting into the product create therisk of fire and electric shock. Takethe following steps immediately.1. Turn off power.2. If you are using the AC adaptor
for power, unplug it from the walloutlet.
3. Contact your original retailer oran authorized CASIO ServiceProvider.
Disassembly and ModificationNever try to take this product apartor modify it in any way. Doing socreates the risk of electric shock,burn injury, or other personal injury.Leave all internal inspection,adjustment, and maintenance up toyour original retailer or authorizedCASIO Service Provider.
Dropping and ImpactContinued use of this product afterit has been damaged by droppingor subjecting it to strong impactcreates the risk of fire and electricshock. Take the following stepsimmediately.1. Turn off power.2. If you are using the AC adaptor
for power, unplug it from the walloutlet.
3. Contact your original retailer oran authorized CASIO ServiceProvider.
662A-E-005A
E-4 662A-E-006A
CleaningBefore cleaning the product, alwaysunplug the AC adaptor from thewall outlet first. Leaving the ACadaptor plugged in creates the riskof damage to the AC adaptor, fire,and electric shock.
BatteriesMisuse of batteries can cause themto leak resulting in damage tonearby objects, or to explode,creating the risk of fire and personalinjury. Always make sure youobserve the following precautions.• Use only batteries that are
specified for use with thisproduct.
• Remove batteries from theproduct if you do not plan to useit for a long time.
ConnectorsConnect only the specified devicesand equipment to the product’sconnectors. Connection of a non-specified device or equipmentcreates the risk of fire and electricshock.
LocationAvoid the following locations forthis product. Such locations createthe risk of fire and electric shock.• Areas subject to high humidity
or large amounts of dust.• In food preparation areas or other
areas subject to oil smoke.• Near air conditioning equipment,
on a heated carpet, in areasexposed to direct sunlight, insideof a vehicle parked in the sun, orany other area that subjects theproduct to high temperatures.
CAUTION
AC Adaptor Misuse of the AC adaptor creates
the risk of fire and electric shock.Always make sure you observethe following precautions.• Do not locate the electric cord
near a stove or other sources ofheat.
• Never pull on the cord whenunplugging from the electricaloutlet. Always grasp the ACadaptor when unplugging.
Misuse of the AC adaptor createsthe risk of fire and electric shock.Always make sure you observethe following precautions.• Insert the AC adaptor into the
wall outlet as far as it will go.• Unplug the AC adaptor from
the wall outlet duringlightening storms or beforeleaving on a trip or other long-term absence.
• At least once a year, unplugthe AC adaptor from the walloutlet and wipe away any dustthat is built up in the areaaround the prongs of the plug.
Relocating the ProductBefore relocating the product,always unplug the AC adaptor fromthe wall outlet and disconnect allother cables and connecting cords.Leaving cords connected creates therisk of damage to the cords, fire,and electric shock.
E-5
Heavy ObjectsNever place heavy object on top ofthe product.Doing so can make the product topheavy, causing the product to tipover or the object to fall from it,creating the risk of personal injury.
Correct Stand* AssemblyAn incorrectly assembled stand cantip over, causing the product to falland creating the risk of personalinjury.Make sure you assemble the standcorrectly, following the assemblyinstructions that come with it. Makesure you mount the product on thestand correctly.
* Stand is available as an option.
IMPORTANT!When using batteries, be sure to replace them or shift to oneof the alternate power sources whenever you notice any ofthe following symptoms.
• Dim power indicator• Instrument does not turn on• Display that is flickering, dim, or difficult to read• Abnormally low speaker/headphone volume• Distortion of sound output• Occasional interruption of sound when playing at high
volume• Sudden power failure when playing at high volume• Flickering or dimming of the display when playing at high
volume• Continued sound output even after you release a key• A tone that is totally different from the one that is selected• Abnormal rhythm pattern and Song Bank play• Loss of power, sound distortion, or low volume when
playing from a connected computer or MIDI device• Abnormally low microphone volume• Distortion of microphone input• Dim power supply indicator when a microphone is used
Display Screen• Never push on the display
screen’s LCD panel or subject itto strong impact. Doing so cancause the LCD panel’s glass tocrack, creating the risk of personalinjury.
• Should the LCD panel ever crackor break, never touch the liquidinside of the panel. LCD panelliquid can cause skin irritation.
• Should LCD panel liquid ever getinside your mouth, immediatelywash out your mouth with waterand contact your physician.
• Should LCD panel liquid ever getinto your eyes or onto your skin,rinse with clear water for at least15 minutes, and then contact aphysician.
Sound VolumeDo not listen to music at very loudvolumes for long periods. Particularcare concerning this precaution isrequired when using headphones.High volume settings can damageyour hearing.
Health PrecautionIn extremely rare cases, exposure tostrong sudden light or flashing lightcan cause momentary musclespasms, loss of consciousness, orother physical problems with someindividuals.• If you suspect that you might be
susceptible to any condition suchas this, be sure to consult withyour physician before using thisproduct.
• Use this product in an area that iswell illuminated.
• Should you ever feel anysymptoms similar to thosedescribed above when using thisproduct, stop using it immediatelyand contact your physician.
662A-E-007A
E-6 662A-E-008A
On-screen fingering and timing indicators• Easy-to-understand on-screen indicators help to simplify keyboard play, even for novices.
100 amazingly realistic tones
Enhanced auto-accompaniment function for greater versatility• 50 built in auto-accompaniment patterns.
100 Built-in Song Bank tunes• A total of 100 built-in Song Bank tunes comes built in for playback enjoyment or play-along practice.
3-Step Lesson System• Develop your musical skills by following the keys as they light. First you become familiar with the
timing of the notes by watching the keys light as you playback one of the 100 built-in Song Banktunes. Next, practice playing along at a pace that’s comfortable for you. Finally, try playing along at thenormal tempo for the Song Bank tune.
• A simulated human voice is used during Step 1 or Step 2 play to call out the fingers you should use toplay the required notes (Voice Fingering). The timing of notes is also indicated on the display screen.
Auto Accompaniment• Simply specify a chord and the keyboard automatically produces the matching rhythm, bass, and
chord patterns. One-touch fill-ins make accompaniments sound interesting and natural.
Transpose Function• An easy operation instantly changes the key of the keyboard.
MIDI compatibility• Connecting to another MIDI device lets you sound notes on both this keyboard and the connected
device by playing on this keyboard.
Microphone jack• Connect a commercially available microphone and you can sing along with Song Bank tunes.
Main Features
E-7662A-E-009A
Contents
Safety Precautions ................E-1
Main Features ........................E-6
General Guide ........................E-8
Attachment of Score Stand ........................E-9
Quick Reference ..................E-10
Power Supply....................... E-11
Using batteries ......................................... E-11
Using the AC Adaptor .............................. E-11
Auto Power Off .........................................E-12
Power On Alert .........................................E-12
Care of Your Keyboard .......E-12
Connections.........................E-13
Phones/Output Jack ................................E-13
Sustain Jack ............................................E-13
Using the Microphone Jack .....................E-13
Accessories and Options .........................E-14
Basic Operations .................E-15
To switch power on and off ......................E-15
To change tones ......................................E-15
Other Useful Functions ............................E-16
Playing the demo tunes ...........................E-17
Playing rhythms .......................................E-18
Using auto-accompaniment .....................E-18
Improvising with the preset patterns ........E-20
3-Step Lesson System ........E-21
Using 3-Step Lesson System ..................E-21
Voice Fingering Guide .............................E-23
Timing Indicator .......................................E-23
Step 1: Master the timing .........................E-24
Step 2: Master the melody .......................E-25
Step 3: Play at normal speed ..................E-25
To practice the left hand part ...................E-26
MIDI .......................................E-27
What is MIDI? ..........................................E-27
General MIDI ...........................................E-27
Technical Reference............E-29
Troubleshooting .......................................E-29
Specifications ...........................................E-31
Appendix ............................... A-1
GM Tone Map List ......................................A-1
Rhythm List ................................................A-2
Fingered Chord Charts ..............................A-3
MIDI Implementation Chart
E-8
General Guide
662A-E-010A
E
J
EDC F H I***** G
M N O P Q R
1 23
7 8 0 A B9
4 65
LK
E-9662A-E-011A
1 MIC VOLUME slider
2 POWER/MODE selector
3 Power indicator
4 MAIN VOLUME slider
5 DEMO button
6 KEY LIGHT button
RHYTHM CONTROLLER7 SYNCHRO/FILL-IN button
8 START/STOP button
9 TEMPO buttons
0 SONG BANK button
A RHYTHM button
B TONE button
C Percussion instrument list
D CHORD root names
E Speakers
F 100 SONG BANK list
G Display
H 50 RHYTHMS listSee “Rhythm List” on page A-2 for details.
I 100 TONES listSee “GM Tone Map List” on page A-1 for details.
J Voice 1 to 5
K TRANSPOSE/TUNE/LOCAL CONTROL operationguide
L Number buttons
3-STEP LESSONM STEP 1 button
N STEP 2 button
O STEP 3 button
P PART SELECT button
Q ONE KEY PLAY buttons
R SPEAK button
** Attachment of Score StandInsert both ends of the music stand providedwith the keyboard into the two holes on thetop surface.
* Rear Panel
U VTS W X S MIDI OUT terminal
T MIDI IN terminal
U SUSTAIN jack
V DC 9V jack
W PHONES/OUTPUT jackFor connection of commercially availableheadphones. Output from the speakers isautomatically cut when headphones areconnected.
X MIC IN jack
E-10
1 Set the POWER/MODE selector to NORMAL.
2 Press the SONG BANK button.
3 Find the tune you want to play in the Song Banklist, and then use the number buttons to input itstwo-digit number.• To select “13 TWINKLE TWINKLE LITTLE STAR”,
input 1 and then 3.
4 Press the STEP 1 button or STEP 2 button.• When you do, the STEP 1 indicator or STEP 2 indicator
appears.• The keyboard sounds a count beat and waits for you
to play something on the keyboard. The keys that youneed to press first flash.
• Play in accordance with the fingerings that appear onthe display.
Quick Reference
662A-E-012A
This section provides a quick overview of keyboard operation using steps one and two of the 3-step lesson feature. See page E-21for detailed explanations of these steps.
5 Play the melody part on the keyboard.
<If you pressed the STEP 1 button in 4 ...>Play the notes with the ONE KEY PLAY buttons.• The accompaniment tempo automatically adjusts to
play along with your melody.
Play the notes on the keyboard.• A sub-melody (obbligato) plays in time with the
melody.• With Step 1, the correct melody note is played no
matter which keyboard key you press.
<If you pressed the STEP 2 button in 4 ...>Play the notes on the keyboard, pressing keys asthey light.• Keep the key depressed as long as it stays lit.• If you selected any song from number 84 through 99,
the lit key goes out as soon as you press it.• The key that corresponds to the next note you need
to play will flash.• After you press the correct melody key,
accompaniment proceeds to the next note.
T w i n k l e
1 3
4 52 5
kT w i n l e
Fingering
SONG BANKindicator appears
E-11
Power Supply
662A-E-013A
This keyboard can be powered by current from a standardhousehold wall outlet (using the specified AC adaptor) or bybatteries. Always make sure you turn the keyboard offwhenever you are not using it.
Using batteriesAlways make sure you turn off the keyboard before loadingor replacing batteries.
To load batteries
1. Remove the batterycompartment cover.
2. Load 6 AA-size batteriesinto the batterycompartment.• Make sure that the positive (+) and negative (–) ends
are facing correctly.
3. Insert the tabs on the battery compartment coverinto the holes provided and close the cover.
NOTE• The keyboard may not function correctly if you load or replace
batteries with power turned on. If this happens, turning thekeyboard off and then back on again should return functionsback to normal.
Important Battery Information The following shows the approximate battery life.
Alkaline batteries .................................. 4 hoursManganese batteries .............................. 1 hourThe above value is standard battery life at normaltemperature, with the keyboard volume at mediumsetting. Temperature extremes or playing at very loudvolume settings can shorten battery life.
WARNINGMisuse of batteries can cause them to leak, resulting in damageto nearby objects, or to explode, creating the risk of fire andpersonal injury. Always make sure you observe the followingprecautions.• Never try to take batteries apart or allow them to become
shorted.• Never expose batteries to heat or dispose of them by
incineration.• Never mix old batteries with new ones.• Never mix batteries of different types.• Do not charge the batteries.• Make sure the positive (+) and negative (–) ends of the
batteries are facing correctly.
CAUTIONMisuse of batteries can cause them to leak resulting in damageto nearby objects, or to explode, creating the risk of fire andpersonal injury. Always make sure you observe the followingprecautions.• Use only batteries that are specified for use with this
product.• Remove batteries from the product if you do not plan to
use it for a long time.
Using the AC AdaptorMake sure that you use only the AC adaptor specified forthis keyboard.
Specified AC Adaptor: AD-5
Note the following important precautions to avoid damageto the power cord.
During Use• Never pull on the cord with excessive force.• Never repeatedly pull on the cord.• Never twist the cord at the base of the plug or connector.• The power cord should not be stretched tight while it is
in use.
During Movement• Before moving the keyboard, be sure to unplug the AC
adaptor from the power outlet.
During Storage• Loop and bundle the power cord, but never wind it
around the AC adaptor.
AC adaptor AD-5
AC outlet
DC 9V jack
E-12 662A-E-014A
IMPORTANT!• Make sure that the keyboard is turned off before connecting or
disconnecting the AC adaptor.• Using the AC adaptor for a long time can cause it to become
warm to the touch. This is normal and does not indicatemalfunction.
Auto Power OffWhen you are using battery power, keyboard power turnsoff automatically whenever you leave it on withoutperforming any operation for about 6 minutes. When thishappens, move the POWER/MODE selector to the OFFposition and then back to NORMAL, CASIO CHORD, orFINGERED to turn power back on.
NOTE• Auto Power Off is disabled (it does not function) when you are
using the AC adaptor to power the keyboard.
Power On AlertKeyboard keys light to alert you if you leave power on anddo not perform any operation for about 6 minutes. Note thatkeys light only, and no sound is produced. When thishappens, press any button or keyboard key to clear the poweron alert.
NOTE• Power on alert operates only when you are powering the
keyboard using the AC adaptor. It does not operate when youare using batteries.
To disable Auto Power Off and power on
alertHold down the TONE button while turning on the keyboardto disable Auto Power Off and power on alert.
NOTE• When these functions are turned off, the keyboard does not
turn off automatically and no alert is performed no matter howlong it is left with no operation being performed.
• Auto Power Off and power on alert are enabled again whenyou manually turn off power and then turn it back on again.
Avoid heat, humidity or direct sunlight.Do not overexpose the instrument to direct sunlight, or placeit near an air conditioner, or in any extremely hot place.
Do not use near a TV or radio.This instrument can cause video or audio interference withTV and radio reception. If this happens, move the instrumentaway from the TV or radio.
Do not use lacquer, thinner or similar chemicalsfor cleaning.Clean the keyboard with a soft cloth dampened in a weaksolution of water and a neutral detergent. Soak the cloth inthe solution and squeeze until it is almost dry.
NOTE• You may notice lines in the finish of the case of this keyboard.
These lines are a result of the molding process used to shapethe plastic of the case. They are not cracks or breaks in theplastic, and are no cause for concern.
Care of YourKeyboard
E-13
White Red PIN plug
Stereo standard plug
Audio connection
PHONES/OUTPUT Jack
Keyboard amp, guitar amp, etc.
1
LEFT RIGHTAUX IN or similar terminal
of audio amplifier
2
3
Connections
Phones/Output JackBefore connecting headphones or other external equipment,be sure to first turn down the volume settings of the keyboardand the connected equipment. You can then adjust volumeto the desired level after connections are complete.
[Rear Panel]
Connecting Headphones (Figure 1)
Connecting headphones cuts off output from the keyboard’sbuilt-in speakers, so you can play even late at night withoutdisturbing anyone.
Audio Equipment (Figure 2)Connect the keyboard to an audio equipment using acommercially available connecting cord with a standard plugon one end and two PIN plugs on the other end. In thisconfiguration, you normally set the input selector of the audioequipment to the terminal (usually marked AUX IN orsomething similar) where the cord from the keyboard isconnected. See the user documentation that comes with youraudio equipment for full details.
Musical Instrument Amplifier (Figure 3)Use a commercially available connecting cord to connect thekeyboard to a musical instrument amplifier.
NOTE• Be sure to use a connecting cord that has standard plugs on
the ends you connect to the keyboard and amplifier.
[Connection Example]
Keyboard or guitar amp
To keyboard’s PHONES/OUTPUT jack
Standard plug
INPUT
662A-E-015A
Sustain JackYou can connect an optional sustain pedal (SP-3 or SP-20) tothe SUSTAIN jack to enable the capabilities described below.
Sustain Pedal
• With piano tones, depressing the pedal causes notes tolinger, much like a piano’s damper pedal.
• With organ tones, depressing the pedal causes notes tocontinue to sound until the pedal is released.
Using the Microphone JackConnecting a commercially available microphone to the MICIN jack makes it possible to sing along with the keyboard’sbuilt-in tunes or with output from a MIDI device. Whenconnecting a microphone, be sure to first adjust the MICVOLUME to a relatively low setting, and then adjust to thelevel you want after connecting.
1. Set the MIC VOLUME slider setting so it is onthe “MIN” side.
2. Turn on the microphone’s on/off switch.
3. Use the MIC VOLUME slider to adjustmicrophone volume to the level you want.
[Rear Panel]
MIC VOLUME slider
Microphone
Microphone on/off switch
SUSTAIN jack
SP-20
E-14 662A-E-016A
IMPORTANT!• Be sure to use the microphone’s on/off switch to turn off
the microphone and to disconnect the microphone fromthe keyboard whenever you are not using it.
Recommended Microphone Type• Dynamic microphone (standard plug)
IMPORTANT!• Be sure to disconnect the microphone from the keyboard
whenever you are not using it.
Howling (Feedback Noise)Any of the following conditions can cause howling (feedbacknoise).
• Covering the head of the microphone with your hand• Positioning the microphone too near to a speaker
Should howling occur, try grasping the microphone furtheraway from the head, and move away from any nearbyspeaker.
Static NoiseFluorescent lighting can cause static noise in the microphonesignal. When this happens, move away from the lighting yoususpect may be causing the static.
Accessories and OptionsUse only the accessories and options specified for thiskeyboard. Use of non-authorized items creates the danger offire, electrical shock, and personal injury.
E-15
BASS PIANO
PERCUSSION (No.99)• PERCUSSION (Tone 99) assigns 35 percussion sounds and
five voice sounds to the keyboard as shown below. Thesounds assigned to each key are indicated above thekeyboard.
662A-E-017A
NOTE• Always enter two digits for the tone number. If you enter only
one digit, the display will automatically return to the previoustone number setting after a few seconds.
• If you change the tone setting while a keyboard key isdepressed, the tone does not change until you release the keyand press a keyboard key again.
• With certain tones (such as percussion sounds and soundeffects), there may be very little or no change at all in the pitch,no matter which keyboard key you press.
• If you input the wrong first digit for a tone number, you canreturn to the previous setting by pressing the TONE button.
Keyboard split tonesSome of the preset tones split the keyboard and assign twoor more sounds. With such a preset tone, the sound produceddepends on what position of the keyboard you play. Forexample, BASS/PIANO (tone 90) puts BASS on the left andPIANO on the right of the keyboard.
<Example>
BASS/PIANO (No.90)
Basic Operations
TEMPO
DEMOMAIN VOLUMETONE
RHYTHM
SONG BANK
Number buttonsPOWER/MODE
START/STOPSYNCHRO/FILL-IN
This part of the manual provides you with the basicinformation you need to use your keyboard.
To switch power on and off
1. Set the POWER/MODE selector to NORMAL.
2. Press the keyboard keys.
3. Use the MAIN VOLUME slider to set the volumeto a relatively low level.
4. To switch power off, set the POWER/MODEselector to OFF position.
To change tones
1. Look at the tone list* printed on the keyboard’sconsole and find the one you want.* See “GM Tone Map List” on page A-1 for details.
2. Press the TONE button.
3. Use the number buttons to input the 2-digitnumber that identifies the tone you want toselect.Example: To select “26 ACOUSTIC BASS”, input 2 and
then 6.
G r a n d P n o
Indicator appears
A c o . B a s s
E-16
Other Useful FunctionsTo change the key of the keyboardThe transpose feature of this keyboard lets you raise or lowerits key in semitone increments. This means you can easilymatch to suit someone’s voice, and you can eliminate sharpsand flats from music making it easier to play.
1. While in any mode besides the Song Bank Mode(indicated when the SONG BANK indicator islit), hold down the TONE button and press theRHYTHM button.• Perform step 2 within five seconds after performing
step 1.
2. Use the TEMPO buttons to change the key ofthe keyboard.Example: To change the tuning to B (indicated by -1
since it is one tone below C, which is thenormal tuning of the keyboard).
T r a n s
T r a n s ( – )
F# G A B C D E FA B C# E Key :
: Pressing: Pressing
Display :
Trans (–) Trans (+)
<Keys and their indicators>
<Note Names>
B (-1) tuningNormal tuning
D F G A
B
C
B
C
EC D E F G A B C
B
C D E F G A C
662A-E-018A
BASS DRUM
SIDE STICK
ACOUSTIC SNARE
HAND CLAP
ELECTRIC SNARE
LOW FLOOR TOM
CLOSED HI-HAT
HIGH FLOOR TOM
PEDAL HI-HAT
LOW TOM
OPEN HI-HAT
LOW MID TOM
HIGH MID TOM
CRASH CYMBAL 1
HIGH TOM
RIDE CYMBAL 1
CHINESE CYMBAL
RIDE BELL
TAMBOURINE
SPLASH CYMBAL
COWBELL
CRASH CYMBAL 2
CLAVES
RIDE CYMBAL 2
HIGH BONGO
LOW BONGO
MUTE HIGH CONGA
OPEN HIGH CONGA
LOW CONGA
HIGH TIMBALES
LOW TIMBALES
HIGH AGOGO
LOW AGOGO
CABASA
MARACAS
VOICE 1
VOICE 2
VOICE 3
VOICE 4
VOICE 5
PolyphonyThe term polyphony refers to the maximum number of notesyou can play at the same time. This keyboard has 12-notepolyphony, which includes the notes you play as well as therhythms and auto-accompaniment patterns that are playedby the keyboard. This means that when a rhythm or auto-accompaniment pattern is being played by the keyboard, thenumber of notes (polyphony) available for keyboard play isreduced. Also note that some of the tones offer only 6-notepolyphony.
• When rhythm or auto accompaniment is playing, thenumber of sounds simultaneously played is reduced.
• Though you can sound up to 12 notes at one time, only thelast four keyboard keys pressed light up.
E-17
NOTE• If you leave the tuning screen on the display for about five
seconds without doing anything, the screen is automaticallycleared.
• In step 2 of the above procedure, you could also use the numberbuttons to input a value from 00 to 50.
• Pressing both of the TEMPO buttons ( / ) at the same timereturns the tuning setting to 00.
• Pressing the SONG BANK button changes the tuning settingto 00.
• The tuning setting does not affect any of Song Bank tunes.• You can tune the keyboard within a range of approximately
±50 cents (100 cents = 1 semitone).• The tuning setting is automatically set to 00 whenever you turn
the keyboard on.• Pressing the DEMO button changes the tuning setting to 00.• The tuning operation does not affect rhythm (99 PERCUSSION).
Playing the demo tunesYou can set up the keyboard to continually play its 100 built-in Song Bank tunes.Keyboard keys light to indicate the melody notes of the demotune as it plays.
To start demo tune play
1. Switch power on and adjust the volume level.
2. Press the DEMO button.• Demo tune play continues in a sequential endless loop
until you switch it off.• The number and name of the demo tune currently
playing are shown on the display.• You can play along on the keyboard while a demo
tune is playing back.
3. You can change the demo tune play being playedby pressing the number buttons.• The Song Bank tunes play back in tune number
sequence, starting from the one you select.
To stop demo tune playPress the DEMO button or START/STOP button again to stopdemo tune play.
662A-E-019A
NOTE• If you leave the transpose screen on the display for about five
seconds without doing anything, the screen is automaticallycleared.
• You cannot change the transpose setting while the keyboard isin the Song Bank Mode.
• In step 2 of the above operation, you could also use the numberbuttons 0 to 5 to specify C through F.
• Pressing both of the TEMPO buttons ( / ) at the same timereturns the transpose setting to C(0).
• The transpose setting is automatically set to C(0) wheneveryou turn keyboard power on.
• The transpose setting is automatically set to C(0) wheneveryou press the SONG BANK button.
• The pitch of a transposed note depends on the tone you areusing. If the transpose operation causes a note to exceed therange of the tone you are using, the same note in the highestoctave of the tone’s range is substituted.
• The transpose operation does not affect tone number 99(PERCUSSION) or auto-accompaniment rhythms.
• Transposing tones 75 through 79 and 90 through 96 changesthe range of keys to which each of the tones is assigned.
• The transpose setting is automatically set to C(0) wheneveryou press the DEMO button.
To tune the keyboardA simple operation lets you tune the keyboard to anothermusical instrument.
1. While in any mode besides the Song Bank Mode(indicated when the SONG BANK indicator islit), hold down the TONE button and press theSONG BANK button.• Perform step 2 within five seconds after performing
step 1.
2. Use the TEMPO buttons to change the tuning ofthe keyboard.Example: To lower tuning by 20
T u n e
T u n e ( – )
E-18
6. Use the TEMPO buttons to adjust the tempo ofthe rhythm.
• Each time you press one of the TEMPO buttons whilethe tempo value is displayed, the tempo settingchanges one step, within the range of 040 to 255.
• The initial default tempo setting when you turn onpower is 120.
• After displaying the current tempo setting by pressingthe TEMPO button in step 6, you can also input thetempo setting you want by inputting a three-digitvalue with the number buttons.
• Holding down either of the TEMPO buttons changesthe tempo setting at high speed.
• To reset the tempo to the standard value of eachrhythm, press both TEMPO buttons.
7. To stop rhythm play, press the START/STOPbutton again.
Using auto-accompanimentThis keyboard features 50 accompaniment patterns that letyou add full accompaniments to your performancesautomatically. With auto-accompaniment, part of thekeyboard is reserved as an accompaniment keyboard. As youplay your chords on the accompaniment keyboard, theaccompaniment pattern adjusts automatically to follow theprogression you play.You get a choice between two different methods for chordplay. FINGERED lets you play chords as you normally do,while CASIO CHORD makes it possible to play fully formedchords with one finger.
About the accompaniment keyboardThe lower (left) 1.5 octaves are reserved for use as anaccompaniment keyboard whenever you select CASIOCHORD or FINGERED with the POWER/MODE selector.The panel above the accompaniment keyboard keys is markedwith the names of the notes they play. The remainder of thekeyboard (the part that is not included in the accompanimentkeyboard) is called the melody keyboard. Please be sure toremember these terms, because they will be used throughoutthe rest of this manual.
Accompanimentkeyboard
Melody keyboard
662A-E-020A
The entire keyboard can be used for melody play whilethe POWER/MODE selector is set to NORMAL.( )
NOTE• Only the following buttons are enabled while a Song Bank tune
is being played.• MAIN VOLUME slider• Number buttons• START/STOP button• POWER/MODE selector (OFF)• DEMO button• KEY LIGHT button• SPEAK button
• You cannot change the tone being used for the melody of aSong Bank tune.
Playing rhythmsThis keyboard features a collection of 50 exciting built-inrhythm patterns. Each pattern provides percussion back upfor all your performances.
To select and play a rhythm
1. Set the POWER/MODE selector to NORMAL.
2. Find the rhythm you want to use in the “RhythmList” (page A-2) and note its rhythm number.
3. Press the RHYTHM button.• When you do, the RHYTHM indicator appears.• The number and name that appear on the display
indicate the currently selected rhythm.
4. Use the number buttons to input the 2-digitrhythm number for the rhythm you want to use.Example: To select “37 SAMBA”, input 3 and then 7.
• Be sure to always specify a 2-digit number.• If you discover a mistake before you input the second
digit, press the RHYTHM button to return to thepreviously set rhythm number.
• You can change to another rhythm even while thecurrent rhythm is sounding.
5. Press the START/STOP button to start play of therhythm.• When you do, the selected rhythm starts to sound.
S amb a
E-19
C
Caug (*1)
Cm7
C75 (*1)
Cmadd9
Cm
Csus4
CM7
C7sus4
CmM7
Cdim
C7
Cm75
Cadd9
Cdim7 (*1)
*1 With this chords, the lowest note in your fingering isalways used as the root. Make sure that your fingeringcorrectly identifies the root you want to use.
662A-E-021A
5. Continue pressing different keys on theaccompaniment keyboard to play your chordprogression.
6. To stop auto-accompaniment play, press theSTART/STOP button again.
Using standard fingeringsThe FINGERED mode lets you play a wider variety of chords.In this mode, you can start play of an accompaniment patternby pressing three or four of the accompaniment keyboardkeys.This keyboard is capable of recognizing 15 different chords.The following shows the fingerings of these chords with aroot of C. Note that you can omit the fifth notes (which areshown inside parentheses in the illustrations below) toproduce 7, m7, M7, add9, madd9, and mM7 chords.
Using the CASIO CHORD systemThe CASIO CHORD system lets you easily play the four maintypes of chords. Play of chords is simplified as shown in thechart below.
Example
C(C MajorChord)
Cm(C MinorChord)
C7(C SeventhChord)
Cm7(C MinorSeventhChord)
Keys
Pressing oneaccompanimentkey
Pressing twoaccompanimentkeys
Pressingthreeaccompanimentkeys
Pressing fouraccompanimentkeys
Type
Majorchord
Minorchord
Seventhchord
Minorseventhchord
CC DE FFE GA
A BB
CC DE FE
CC DE FFE GA
A BB
CC DE FE
CC DE FFE GA
A BB
CC DE FE
CC DE FFE GA
A BB
CC DE FE
NOTE• The bottom (leftmost) note that you play determines the name
of the chord. If the bottom note is a C for example, the keyboardproduces a C chord.
• When pressing more than one accompaniment key, it makesno difference whether the keys to the right of the bottom noteare white or black.
To play a CASIO CHORD auto-accompaniment
1. Use the POWER/MODE selector to select CASIOCHORD.
2. Select an auto-rhythm as described under “Toselect and play a rhythm” on page E-18.
3. Start play of the rhythm.• If you want to start play of the normal rhythm pattern,
press START/STOP.• You can also use synchro start (page E-20) to start
rhythm play.
4. Press either one or up to four keys on theaccompaniment keyboard, and thecorresponding accompaniment starts to playautomatically.
Chord name
E-20
Improvising with the preset patternsPressing the START/STOP button to start rhythm play causesthe normal version of the pattern to be played. You can alsoplay a variation of the rhythm using the operation describedbelow.
Using fill-in rhythmYou can insert a fill-in rhythm by pressing the SYNCHRO/FILL-IN button while an auto-rhythm plays.
Using Synchro startYou can start the rhythm and accompaniment pattern at thesame time, with your play of the accompaniment keyboard.To do this, follow the steps below.
1. Set the POWER/MODE selector to the CASIOCHORD or FINGERED position.
2. Select an auto-rhythm.
3. Press the SYNCHRO/FILL-IN button.
4. Press the accompaniment keys to play the firstchord. As soon as you do, the auto-accompaniment pattern begins to play.
5. To stop the auto-accompaniment pattern play,press the START/STOP button.
NOTE• If you set the POWER/MODE selector to NORMAL in step 1 on
page E-18, the operation in step 4 starts play of the rhythm(percussion instruments) only.
662A-E-022A
IMPORTANT!• If you play one or two notes only in the left hand, or three
notes that do not make up a recognizable chord formation,no sound will be produced. The FINGERED mode requiresa conventional three or four-note chord formation toproduce an auto-accompaniment. Also, note that auto-chords only work in conjunction with rhythm patterns, andnot independently of them.
NOTE• The above examples show only one of the possible fingerings
for each chord. Note that you can play the notes that form achord in any combination. Each of the following fingerings forexample, produces the same C chord.
Accompanimentkeyboard
• See the “Fingered Chord Charts” on page A-3 forinformation on the fingerings of chords for all roots.
To play a FINGERED auto-accompaniment
1. Use the POWER/MODE selector to selectFINGERED.
2. Select an auto-rhythm as described under “Toselect and play a rhythm” on page E-18.
3. Start play of the rhythm.• If you want to start play of the normal rhythm pattern,
press START/STOP.• You can also use synchro start (on this page) to start
rhythm play.
4. Play a chord on the accompaniment keyboardto start play of the auto-accompaniment.
5. Continue pressing keys on the accompanimentkeyboard to play your chord progression.
6. To stop auto-accompaniment play, press theSTART/STOP button again.
Chord name
E-21
3-Step Lesson System
662A-E-023A
Using 3-Step Lesson SystemEven individuals who cannot play the keyboard at all canfollow along with the 100 built-in Song Bank tunes with theONE KEY PLAY buttons. You can also use the 3-Step LessonSystem to learn at your own pace. Play slowly at first untilyou are able to play along at normal speed.Of the 100 built-in tunes, numbers 00 through 83 feature auto-accompaniment (auto-accompaniment tunes), while 84through 99 are played using both hands (two-hand tunes).
The 3-Step Lesson System can be used with the following 3-step lesson plan to master keyboard play.
Step 1: Master the timingPressing the ONE KEY PLAY buttons plays themelody for an auto-accompaniment tune or the righthand part for two-hand tunes. In both cases, the auto-accompaniment (the left hand part in the case of two-hand tunes) is played automatically by the keyboard.In place of the ONE KEY PLAY buttons, you can alsopress any key of the keyboard to play the melody orright hand part. The purpose of this step is tofamiliarize yourself with the timing required to playmelody notes.
Step 2: Master the melodyIn this step, you use the display to learn which fingersyou should use to play, and the key light system tolearn which keyboard keys to press. You can play atthe pace you want, because the auto-accompanimentor left hand part waits until you press the correct key.
Step 3: Play at normal speedAt this level, the keyboard’s keys still light to indicatewhich notes to play, but they no longer wait for youto press the correct key. The auto-accompaniment orleft hand part is played at normal speed.
NOTE• You may not be able to see the keyboard keys light under direct
sunlight or in other brightly lit areas.• You can press the ONE KEY PLAY, STEP 1, STEP 2, and STEP
3 buttons at any time, except while a demo tune is playing. Toreturn the keyboard to its normal mode, press the SONG BANKbutton.
3-Step Lesson System Tempo SettingYou can use the procedure in step 6 of the procedure on pageE-19 to set the tempo of the left-hand part for Song Bank and3-Step Lesson System play (Step 1 through 3).This means you can use a slower tempo at the beginning,and then increase it as you learn. Press both of the TEMPObuttons ( and ) at the same time to return the tempo toits initial preset setting.
To play a built-in Song Bank tune
1. Look up the number of the tune you want to playin the Song Bank list.
2. Press the SONG BANK button until the SONGBANK indicator appears.• This causes the number and name of the currently
selected Song Bank tune to appear on the display.
3. Input the two digit number for the tune you wantto play.Example: To select “13 TWINKLE TWINKLE LITTLE
STAR”, input 1 and then 3.
T w i n k l e 4. Press the START/STOP button to start play of the
selected tune.• The tune you select plays repeatedly, with the
keyboard keys lighting to indicate the melody notes.
STEP 1STEP 2 STEP 3
TONE
PART SELECT
SONG BANKKEY LIGHTSPEAK
ONE KEY PLAY
START/STOP
E-22
5. To stop Song Bank tune play, press the START/STOP button again.
6. To exit the Song Bank Mode, press the SONGBANK button again.• When you do, the SONG BANK indicator goes out.
NOTE• Always enter two digits for the Song Bank number.• You can input a Song Bank tune number even while another
Song Bank tune is playing.• If you input the wrong first digit for a Song Bank tune number,
you can return to the previous setting by pressing the SONGBANK button.
• The RHYTHM button is disabled in the Song Bank Mode. Ifyou want to play a rhythm, press the SONG BANK button toreturn to the normal mode first.
Key Lighting System Operation and
Display Contents During Song Bank PlayKeyboard keys light to show the keys that should be pressedto play along with Song Bank tunes as they play back. At thesame time, the display shows fingerings, chord names, tempoand other information.
kT w i n l e
FingeringChord nameTempo value
Crossed Finger IndicationsThe display also shows when you have to cross fingers toplay notes, and in which direction your fingers should cross.
Example: Display for playing the notes below with the righthand
C EDA B3 31 12
C EDA B
Using the Song BankCrossed finger display
• B and C indicate that the index finger should cross overthe thumb.
• C and D indicate that the thumb should cross under theindex finger.
Key Lighting During Song Bank PlayWhen you play back a Song Bank tune, keyboard keys lightto show you the notes that are being played.
Auto-accompaniment Song Bank TuneChord and melody part keys light.
NOTE• Some Song Bank tunes use chords (such as C6) that cannot
be played with the FINGERED setting (page E-19). In theFINGERED mode, chords may sound different from the onesproduced by Song Bank tune playback, even if you finger thechords as indicated by the lit keys.
Two-hand Song Bank TuneLeft hand and right hand part keys light.
662A-E-024A
Melody note lights.Chord
The root (the C-note ofa C-chord) and othernotes that make up thechord alternately light.
Left hand part Right hand part
E-23
Key Lighting System Operation and Display
Contents During 3-step Lesson PlayWhenever you select an Auto Accompaniment tune (00 to83) for 3-step lesson play, the key lighting system shows youwhich keys to press, while the display shows you thefingerings.
Note PitchThe keyboard key that should be pressed lights. The fingersyou should use to play the notes are also shown on the display.
Note LengthKeyboard keys stay lit for as long as the note should beplayed. The fingerings also remain on the display for thelength of the note.
Next NoteThe keyboard key for the next note to be played flashes, whilea number appears on the display near the finger you shoulduse to play the next note.
Series of Same Pitch NotesThe keyboard key light turns off momentarily between thenotes and lights again for each successive note. The fingeringsalso turn off and back on again.
Flash
Next noteCurrent note
Lit Flash Lit Flash
1st Note 2nd Note 3rd Note
Lit
Key light
Example: When play requires pressing keys with fingers3, 2, and then 1
662A-E-025A
Voice Fingering GuideVoice fingering guide uses a simulated human voice to callout fingering numbers during Step 1 and Step 2 one-handpart practice. If you need to press a key with your thumb, forexample, voice fingering guide says, “One!” In the case of achord to be played with your thumb, middle and little finger,voice fingering guide says, “One, three, five!”Voice Fingering Guide calls out fingerings only when you donot press the proper key when you should.
To turn voice fingering guide on and offUse the SPEAK button to turn voice fingering guide on andoff.
Timing IndicatorThe timing indicator helps you become familiar with tunesyou are playing for the first time by indicating the timing ofnotes you play on the keyboard. Timing is easier to see whenyou use a slow tempo during lesson play.
Using the Timing IndicatorThe timing indicator shows the timing of notes contained inthe currently selected part (R or L). Notes are indicated astwo-segment blocks that scroll from the top of the display,down to the bottom. A note is played when its block reachesthe bottom of the display.
• Each two-segment block can indicate one or more notes,depending on the tune you are playing.
NOTE• The Timing Indicator shows note timing whenever you play back
a Song Bank tune and during a 3-Step Lesson.• Note that the Timing Indicator shows approximate timing only.
During a tune, the indicated timing can be anywhere from aneight note to a 32nd off of actual timing.
Voice fingering guide indicator
NOTE• Note length is not indicated when you are using two-hand tunes
(84 to 99) with 3-Step Lesson Steps 1 and 2. As soon as youpress a lit key, it goes out and the next key to be played startsto flash.
• Note length is indicated by the key light system when you usea two-hand tune with Step 3. In this case, the next key to bepressed does not flash when you press a lit key and the nextfinger number does not appear on the display. Only the currentfinger number is shown.
Upcoming notetiming
Note playedhere
E-24
Turning Off Key Lighting
1. Press the KEY LIGHT button.• The KEY LIGHT indicator disappears when the key
light system is turned off.• Press the KEY LIGHT button again to turn key lighting
back on.
NOTEKey lighting turns on automatically in any of the following cases:• When keyboard power is turned on.• When demo tune play is started.• When the SONG BANK button is pressed in the normal mode
(page E-21).• When the power on alert function operates (page E-12).
Number of Simultaneously Lit KeysUp to four keyboard keys can be lit at the same time.
To change the tone used for the melody
of a Song Bank tune
1. Following step 3 of the procedure on page E-21,press the TONE button.• Both the SONG BANK indicator and TONE indicator
appear, along with the tone number and name of thetone that is currently assigned to the keyboard.
2. Input a value to select the tone you want to use.
NOTE• Selecting another Song Bank tune switches the tone setting to
the newly selected tune’s preset melody tone.• The tone assigned to the keyboard is the same one specified
for the melody of the Song Bank tune.• The above procedure can be used to change the Song Bank
melody tone before starting play or while play is already inprogress.
• You can also change the tone of two-hand tunes (tune numbers84 to 99). Note however, that selecting a sustainable tone (likean organ tone) when using 3-Step Lesson Step 1 or Step 2 (inwhich accompaniment waits for correct input from you beforeproceeding), can cause notes of the auto accompaniment tobe sustained while the keyboard is waiting for your input. If thishappens, play something on the keyboard to stop the sustainednote.
662A-E-026A
Step 1: Master the timing
1. Press the STEP 1 button.• When you do, the STEP 1 indicator appears.• After a count sounds, the keyboard stands by and
waits for you to play the first note of the tune. If thetune includes intro measures, the keyboard entersstandby after the intro measures are complete.
2. Press the ONE KEY PLAY buttons to play eachnote of the tune.• The accompaniment (left hand) part of the tune
follows along as you play the melody (right hand)part.
• The keyboard key that corresponds to the next noteto be played flashes, and lights when you play thenote.
• The rhythm (percussion) part does not sound.
3. Try pressing any one of the keyboard keys inplace of the ONE KEY PLAY buttons.• Pressing any keyboard key plays the correct melody
(right hand part) note.• Pressing more than one key at the same time counts
as a single melody note. Pressing a key while anotherkey is held down is counted as two melody notes.
4. To stop play at any time, press the START/STOPbutton.• When you do, the STEP 1 indicator goes out.
kT w i n l e
Fingering
The correct note is played even if you donot press the key that is lit.
KEY LIGHT indicator
E-25
Step 3: Play at normal speed
1. Press the STEP 3 button.• When you do, the STEP 3 indicator appears.• Play starts after a count sounds.
2. Play along on the keyboard, following the keysas they light.• The accompaniment (left hand) part of the tune plays
at normal speed, regardless of what you play on thekeyboard.
• With an auto-accompaniment tune, the keyboard keythat corresponds to the next note to be played flashes,and lights when the note should be played.
• With a two-hand tune, the applicable keyboard keyremains lit as long as its note plays. In this case,however, the key for the next note to be played doesnot flash. Keys light when their notes start to play.
3. To stop play at any time, press the START/STOPbutton.• When you do, the STEP 3 indicator goes out.
662A-E-027A
Step 2: Master the melody
1. Press the STEP 2 button.• When you do, the STEP 2 indicator appears.• After a count sounds, the keyboard stands by and
waits for you to play the first note of the tune. If thetune includes intro measures, the keyboard entersstandby after the intro measures are complete.
2. Play the notes indicated by the 3-Step LessonSystem.• The accompaniment (left hand) part of the tune
follows along as you play the melody (right hand)part.
• The keyboard key that corresponds to the next noteto be played flashes, and lights when you play thenote.
• The rhythm (percussion) part does not sound.
3. To stop play at any time, press the START/STOPbutton.• When you do, the STEP 2 indicator goes out.
Press keyboard keys as they light. More than onekey may light when you are playing a two-hand tune.Press all keys that light.
Fingering
kT w i n l e
Fingering
kT w i n l e
E-26
To practice the left hand partOnce you master right hand part play, you can use the two-hand tunes (numbers 84 through 99) to practice left hand part.
1. Press the SONG BANK button until the SONGBANK indicator appears.• This causes the number and name of the currently
selected Song Bank tune to appear on the display.
2. Input the two digit number for the tune you wantto play.
3. Press the PART SELECT button to switch the lefthand play.
4. Press the STEP 1, STEP 2, or STEP 3 button.• When you do, the STEP 1, STEP 2, or STEP 3 indicator
appears.• After a count beat sounds, the right-hand part starts
to play and the keys for the left-hand part notes flash.
5. Press the PART SELECT button to return the partselection to its previous setting.
6. To interrupt play of the melody, press the START/STOP button.• When you do, the STEP 1, STEP 2, or STEP 3 indicator
disappears.
662A-E-028A
Lit
E-27
MIDI
What is MIDI?The letters MIDI stand for Musical Instrument DigitalInterface, which is the name of a worldwide standard fordigital signals and connectors that makes it possible toexchange musical data between musical instruments andcomputers (machines) produced by different manufacturers.
MIDI Connections
General MIDIGeneral MIDI standardizes MIDI data for all sound sourcetypes, regardless of manufacturer. General MIDI specifiessuch factors as tone numbering, drum sounds, and availableMIDI channels for all sound sources. This standard makes itpossible for all MIDI equipment to reproduce the samenuances when playing General MIDI data, regardless of themanufacturer of the sound source.Though the sound source of this keyboard is not GeneralMIDI compatible, you can still connect the keyboard to acomputer or other MIDI equipment to playback General MIDIdata that is widely available in stores, over computernetworks, and from other sources.
NOTE• General MIDI data made up of a large number of parts may not
play correctly on this keyboard.• You will have most success playing back General MIDI data
that has few parts and is made up of parts on channels 1, 2, 3,4, and 10.
MessagesThere is a wide variety of messages defined under the MIDIstandard, and this section details the particular messages thatcan be sent and received by this keyboard.
NOTE ON/OFFThis message sends data when a key is pressed (NOTE ON)or released (NOTE OFF).A NOTE ON/OFF message includes a note number (toindicate note whose key is being pressed or released) andvelocity (velocity=100 when the volume value of this unit is9 to 2, and velocity=75 when the volume value is 1 or 0).NOTE ON velocity is always used to determine the relativevolume of the note. This keyboard does not receive NOTEOFF velocity data.Whenever you press or release a key on this keyboard, thecorresponding NOTE ON or NOTE OFF message is sent byconstant velocity from the MIDI OUT terminal.
PROGRAM CHANGEThis is the tone selection message. PROGRAM CHANGE cancontain tone data within the range of 0 to 127.A PROGRAM CHANGE message (0 to 99) is sent out throughthis keyboard’s MIDI OUT terminal whenever you manuallychange its tone number. Receipt of a PROGRAM CHANGEmessage from an external machine changes the tone settingof this keyboard.This keyboard can send tone data within the range of 00 to99 and receive tone data within the range of 0 to 127*. Eachof the 128 General MIDI tones is automatically assigned toone of the keyboard’s 100 built-in tones as shown on page A-1. Select this setting when you want to listen to General MIDIdata from a computer or other external equipment.
* When GM mapping is turned on (page E-28). When turnedoff, tone data is received in the range of 0 to 99.
NOTE• Channel 10 is for the drum part only, and it does not receive
Program Change messages. When receiving MIDI data, itsounds percussion sounds produced by this keyboard.
PITCH BENDThis message carries pitch bend information for smoothlysliding the pitch upwards or downwards during keyboardplay. This keyboard does not send pitch bend data, but it canreceive such data.
CONTROL CHANGEThis message adds effects such as vibrato and volume changesapplied during keyboard play. CONTROL CHANGE dataincludes a control number (to identify the effect type) and acontrol value (to specify the on/off status and depth of theeffect).The following is a list of data that can be received usingCONTROL CHANGE.
662A-E-029A
MIDI IN MIDI OUTMIDI IN MIDI OUT
Computer etc.
Effect Control Number
VOLUME 7
HOLD1 64
MODULATION 1
E-28 662A-E-030A
TEMPORHYTHM
SONG BANK
To turn on LOCAL CONTROL/To turn off GMmapping
1. While in any mode besides the Song Bank Mode(indicated when the SONG BANK indicator islit), hold down the RHYTHM button and pressthe SONG BANK button.• Perform step 2 within five seconds after performing
step 1.
2. Use the TEMPO button ( ) to turn on localcontrol.• This also turns off GM mapping.
L o c a l NOTE• Note that LOCAL CONTROL is also turned on automatically
whenever you turn on power, or when you press any of thefollowing buttons.• START/STOP (to start rhythm or Song Bank tune play)• ONE-KEY PLAY• STEP 1• STEP 2• STEP 3• DEMO (to start demo tune play)
• See the GM Tone Map List at the back of this manual forinformation about tone assignments while GM mapping is turnedon.
LOCAL CONTROL (Default: on) /GM mapping(Default: off)This setting determines whether or not the keyboard andsound source of this keyboard are connected internally. Whenrecording to a computer or other external device connectedto this keyboard’s MIDI IN/OUT terminal, it helps if youturn LOCAL CONTROL off.
on: Anything played on the keyboard is sounded by theinternal sound source and simultaneously output as aMIDI message from the MIDI OUT terminal.
oFF: Anything played on the keyboard is output as a MIDImessage from the MIDI OUT terminal, without beingsounded by the internal sound source. Turn LOCALCONTROL off whenever you are using the MIDI THRUfunction of a computer or other external device. Alsonote that no sound is produced by the keyboard ifLOCAL CONTROL is turned off and no external deviceis connected.
NOTE• When you are using this keyboard in a stand-alone
configuration, keyboard keys do not light while local control isturned off.
To turn off LOCAL CONTROL/To turn on GMmapping
1. While in any mode besides the Song Bank Mode(indicated when the SONG BANK indicator islit), hold down the RHYTHM button and pressthe SONG BANK button.• Perform step 2 within five seconds after performing
step 1.
2. Use the TEMPO button ( ) to turn off localcontrol.• This also turns on GM mapping.
L o c a l
E-29
Technical Reference
TroubleshootingBe sure to check the following table whenever you experience problems with keyboard operation.
CauseSymptom Action
• No sound when keyboard keysare pressed.
• Any of the following symptomswhile using battery power.
• Key light stays on.
• Keyboard keys light but nosound is produced.
1. Power supply problem.
2. Volume setting is too low.
3. Headphones are plugged intothe keyboard.
4. The POWER/MODE selector isin the CASIO CHORD orFINGERED position.
5. Tone “99 PERCUSSION” isselected and you are pressingkeys that are not assigned tones.
6. LOCAL CONTROL is off.
• Low battery power
• Keyboard is waiting for play ofthe correct note during Step 1or Step 2 play.
• Power on alert is telling you thatpower is left on.
1. Correctly attach the ACadaptor, make sure thatbatteries (+/–) are facingcorrectly, and check to makesure that batteries are not dead.
2. Use the MAIN VOLUME sliderto increase volume.
3. Unplug the headphones fromthe PHONES/OUTPUT jack.
4. Normal play is not possible onthe accompaniment keyboardwhile the POWER/MODEselector is set to CASIOCHORD or FINGERED.Change the POWER/MODEselector setting to NORMAL.
5. While “99 PERCUSSION” isselected, you can use only keysthat are marked on the consolewith illustrations of percussioninstruments.
6. Turn on LOCAL CONTROL.
• Replace the batteries with a setof new ones or use the ACadaptor.
1. Press the lit key to continue withStep 1 or Step 2 play.
2. Press the START/STOP buttonto quit Step 1 or Step 2 play.
• Press any button or keyboardkey to resume normaloperation with the keyboard inits initial power on setting.
662A-E-031A
See Page
Page E-11
Page E-15
Page E-13
Page E-18
Page E-15
Page E-28
Page E-11
PagesE-24, 25PagesE-24, 25
Page E-12
• Dim power indicator• Instrument does not turn on• Display that is flickering, dim, or difficult to read• Abnormally low speaker/headphone volume• Distortion of sound output• Occasional interruption of sound when playing at high volume• Sudden power failure when playing at high volume• Flickering or dimming of the display when playing at high volume• Continued sound output even after you release a key• A tone that is totally different from the one that is selected• Abnormal rhythm pattern and Song Bank play• Loss of power, sound distortion, or low volume when playing from a connected computer or MIDI
device• Abnormally low microphone volume• Distortion of microphone input• Dim power supply indicator when a microphone is used
E-30
CauseSymptom Action
• Keyboard is in the Song BankMode.
• Keyboard is in the Song BankMode.
• Demo tune play is in progress.
• MIDI cables are not connectedproperly.
• The computer’s MIDI THRUfunction is turned on.
1. Use of a microphone that is adifferent from the type that isrecommended.
2. Use of the microphone in thevicinity of fluorescent lighting.
1. Microphone volume setting istoo low.
2. Microphone on/off switch is setto off.
• Press the SONG BANK buttonto return to the normal mode.
• Press the SONG BANK buttonto return to the normal mode.
• Stop demo tune play.
• Connect MIDI cables properly.
• Turn off the MIDI THRUfunction on the computer orturn off LOCAL CONTROL onthe keyboard.
1. Use a full metal shieldedCannon type microphone.
2. Move the microphone awayfrom source of the static.
1. Increase the microphonevolume setting.
2. Change the microphone on/offswitch setting to on.
662A-E-032A
Page E-21
Page E-21
Page E-17
Page E-27
Page E-28
Page E-13
Page E-13
Page E-13
Page E-13
See Page
• RHYTHM button does notwork.
• Cannot change TRANSPOSE/TUNE/LOCAL CONTROLsettings.
• No sound is produced whenplaying MIDI data from acomputer.
• Playing on the keyboardproduces an unnatural soundwhen connected to a computer.
• Static noise when a microphoneis connected.
• No microphone sound.
This is an unavoidable result of the digital sampling process,* and does not indicatemalfunction.* Multiple digital samples are taken for the low range, middle range, and high range of
the original musical instrument. Because of this, there may be a very slight differencein tonal quality and volume between sample ranges.
A tone’s quality and volumesounds slightly differentdepending where it is played onthe keyboard.
E-31
Model: LK-100
Keyboard: 61 standard-size keys; 5 octaves
Key Light System: Can be turned on and off (up to 4 keys can be lit at the same time)
Tones: 100 presets
Polyphony: 12 notes maximum
3-Step Lesson System: Number of simultaneosly lit keys; 43-Steps
Playback: 1 tune repeat playbackVoice Fingering Guide: On/Off
Auto-accompanimentRhythm patterns: 50 presetsTempo: Adjustable, (216 steps, = 40 to 255), initial value; 120Chords: Two systems; CASIO CHORD, FINGEREDOther: Fill-in pattern, Synchro start
Song Bank tunes: 100 tunes
Musical Information Function: Tone, Auto Accompaniment, Song Bank numbers and names; tempo, 3 steplesson display, chord name, fingering, timing indicator, key lighting, voicefingering
Other FunctionsTranspose: F# to C to F: half-noteTuning: Adjustable A4 = Approx. 440 Hz ±50 cents, Initial value: A4 = Approx. 440 Hz
MIDI: 5 multi-timbre receive
Speakers: 10 cm diameter × 2 (Output: 2W+2W)
I/O TerminalsMIDI Terminals: IN, OUTSustain: Standard jackPower Supply: DC 9V jackHeadphones/Output: Stereo standard jack (Output is monaural.)
[output impedance: 78Ω, output voltage: 4V (RMS) MAX]Microphone In: Standard jack (with microphone volume slider)
Input impedance: 2KΩInput sensitivity: 10mV
Power Supply: 2-wayBatteries: 6 AA-sizeBattery life: Approximately 4 hours continuous operation on alkaline batteries
Approximately 1 hour continuous operation on manganese batteriesAC adaptor : AD-5Auto Power Off: Approximately 6 minutes after the last operation
(Operates during battery use only)
Power Consumption: 9 V 7.7 W
Dimensions: 94.5 × 37.3 × 13.5 cm (37 1/4" × 14 11/16" × 5 5/16")
Weight: Approximately 4.7 kg (10.4 lbs) (without batteries)
Specifications
662A-E-033A
* Designs and specifications are subject to change without notice.
Appendix/Apéndice
00 GRAND PIANO01 BRIGHT PIANO02 HONKY-TONK03 E GRAND PIANO04 ELEC PIANO 105 ELEC PIANO 206 ELEC PIANO 307 ELEC PIANO 408 HARPSICHORD09 CLAVI10 ELEC ORGAN 111 ELEC ORGAN 212 ELEC ORGAN 313 ELEC ORGAN 414 CHURCH ORGAN15 PIPE ORGAN16 REED ORGAN17 ACCORDION18 BANDONEON19 HARMONICA20 NYLON STR GT21 STEEL STR GT22 JAZZ GUITAR23 CLEAN GUITAR24 MUTE GUITAR25 DIST GUITAR26 ACOUSTIC BASS27 ELEC BASS28 SLAP BASS29 BANJO30 VIOLIN31 CELLO32 HARP33 STRINGS 134 STRINGS 235 STRINGS 336 SYNTH-STR 137 SYNTH-STR 238 CHOIR AAHS39 SYNTH-VOICE40 TRUMPET41 TUBA42 BRASS SECTION43 FRENCH HORN 144 FRENCH HORN 245 BRASS 146 BRASS 247 SYNTH-BRASS 148 SYNTH-BRASS 249 SYNTH-BRASS 3
Tone No./Tone NameNo de sonido/Nombre de sonido
Tone No./Tone NameNo de sonido/Nombre de sonido
50 SOPRANO SAX51 ALTO SAX52 TENOR SAX53 OBOE54 CLARINET55 PICCOLO56 FLUTE57 RECORDER58 FLUTE ENSEMBLE59 WHISTLE60 SYNTH-LEAD 161 SYNTH-LEAD 262 SYNTH-LEAD 363 CALLIOPE64 SYNTH-PAD 165 SYNTH-PAD 266 SYNTH-PAD 367 BOWED GLASS68 HALO PAD69 SYNTH-BASS70 RAIN DROP71 SF72 SOUNDTRACK73 SPACE PAD74 SYNTH-SFX75 VEHICLE76 TELEPHONE77 SPACE78 INVADER79 FUNNY80 STRINGS PIANO81 STRINGS EP82 CHOIR EP83 CHOIR ORGAN84 STRINGS GUITAR85 STRINGS HARP86 BRASS STRINGS87 VIB PAD88 12STR GUITAR89 CHOIR STRINGS90 BASS/PIANO91 BASS/E PIANO92 BASS/VIB93 BASS/NYLON STR GT94 BASS/DIST GUITAR95 STRINGS/PIANO96 STRINGS/TRUMPET97 VIBRAPHONE98 MARIMBA99 PERCUSSION
662A-E-066AA-1
GM Tone Map List
Lista de asignaciones de sonido GM
GM No.No GM
0132458967
1617181519
10420212322242526272829 30 31 843233 34 3536 37
10540 4142 4345 46 4748 554944505152 9153 85565857605961696263 8370
GM No.No GM
646566 676871727374 7975 76 77788781 86808289909592 93 9854 9438 3996
10397
101102125124126127123106
88 107108109
99 110111112113114115100 116117118119120121122
10 11 1412 13
POPS
00 CLUB POP
01 FUNKY POP
02 SOUL BALLAD
03 POP BALLAD
04 LITE POP
05 16 BEAT FUNK
06 8 BEAT POP
07 POP ROCK
08 DANCE POP
09 POP FUSION
10 FOLKIE POP
ROCK
11 ROCK WALTZ
12 SLOW ROCK
13 SOFT ROCK
14 50’S ROCK
15 60’S SOUL
16 4 BEAT ROCK
17 ROCK
18 TWIST
19 NEW ORLNS R&R
20 R&B
JAZZ/FUSION
21 BIG BAND
22 SWING
23 FOX TROT
24 JAZZ WALTZ
25 LATIN FUSION
DANCE/FUNK
26 TECHNO
27 TRANCE
28 DISCO
29 FUNK
30 RAP
EUROPEAN
31 POLKA
32 MARCH
33 WALTZ
34 SLOW WALTZ
35 TANGO
LATIN/VARIOUS I
36 BOSSA NOVA
37 SAMBA
38 MAMBO
39 REGGAE
40 SKA
41 SALSA
42 FOLKLORE
43 RUMBA CATALANA
VARIOUS II
44 COUNTRY
45 TOWNSHIP
46 SLOW GOSPEL
47 BALADI
48 BAROQUE
49 NEW AGE
Rhythm List
Lista de ritmos
662A-E-067A A-2
662A-E-068AA-3
1234
5: Left hand finger
numbers
: Números de losdedos de la manoizquierda
Fingered Chord Charts
Cuadros de acordes digitadosThis table shows the left-hand fingerings (including inverted forms) for a number ofoften-used chords.
Esta tabla muestra las digitaciones (incluyendo las formas invertidas) para varios delos acordes más a menudo usados.
* Cannot be specified in FINGERED setting because of accompaniment keyboard limitations, but augmentedand diminished (seventh) chords made up of the same component notes (with different base note) can be usedinstead.
Chords with same component notes as B aug ........... D aug, F augChords with same component notes as B aug ............ E aug, G augChords with same component notes as A dim7 ......... C dim7, E dim7, F dim7Chords with same component notes as B dim7 ........ C dim7, E dim7, G dim7Chords with same component notes as B dim7 .......... D dim7, F dim7, A dim7
* No puede especificarse en el ajuste FINGERED debido a las limitaciones del teclado de acompañamiento, peroen su lugar pueden usarse los acordes aumentados y disminuídos (séptima) compuestos por las mismas notascomponentes (con diferente nota básica).
Acordes con las mismas notas componentes como B aumentada ........ D aumentada, F aumentada.Acordes con las mismas notas componentes como B aumentada ......... E aumentada, G aumentada.Acordes con las mismas notas componentes como A dim7 .................... C dim7, E dim7, F dim7.Acordes con las mismas notas componentes como B dim7 ................... C dim7, E dim7, G dim7.Acordes con las mismas notas componentes como B dim7 .................... D dim7, F dim7, A dim7.
662A-E-069A A-4
662A-E-070A
Fu
nct
ion
...
Tra
nsm
itte
dR
eco
gn
ized
Rem
arks
Bas
icD
efau
ltC
han
nel
Ch
ang
ed
Def
ault
Mo
de
Mes
sag
esA
lter
ed
No
teN
um
ber
Tru
e vo
ice
Vel
oci
tyN
ote
ON
No
te O
FF
Aft
erK
ey’s
To
uch
Ch
’s
Pit
ch B
end
er
1C
on
tro
l6,
38
Ch
ang
e7 10 11 64
1 1
Mod
e 3
X
36-9
6
X 9
nH V
= 1
00
X 9
nH V
= 0
X X X X X X X X O
*1: D
epen
ds o
n to
ne*1
: Dep
ende
en
el s
onid
o
*2 =
no
rela
tion
*2 =
sin
rel
ació
n
Mod
ulat
ion
Dat
a en
try
Vol
ume
Pan
Exp
ress
ion
Hol
d1
1-4,
10
1-4,
10
Mod
e 3
X
0-12
736
-96
*1
O 9
nH V
= 1
-127
X 9
nH V
= 0
,8nH
V =
*2
X X O O X O X X O
Ver
sion
: 1.0
Mod
el L
K-1
00M
IDI I
mp
lem
enta
tio
n C
har
t
662A-E-071A
Mod
e 1
: OM
NI O
N, P
OLY
Mod
e 2
: OM
NI O
N, M
ON
OO
: Yes
Mod
e 3
: OM
NI O
FF
, PO
LYM
ode
4 : O
MN
I OF
F, M
ON
OX
: No
100,
101 12
012
1
Pro
gra
mC
han
ge
:Tru
e #
Sys
tem
Exc
lusi
ve
Sys
tem
: S
on
g P
os
Co
mm
on
: S
on
g S
el:
Tu
ne
Sys
tem
: C
lock
Rea
l Tim
e:
Co
mm
and
s
Au
x:
Lo
cal O
N/O
FF
: A
ll n
ote
s O
FF
Mes
sag
es:
Act
ive
Sen
se:
Res
et
Rem
arks
X X X
O 0
-99
X X X X X X X X X X
RP
N L
SB
, MS
BA
ll so
und
off
Res
et a
ll co
ntro
ller
*3: D
epen
ds o
n G
M M
ap s
ettin
g
*3: D
epen
de e
n el
aju
ste
de m
apa
GM
X X X
O 0
-127
, 0-9
9 * 3
X X X X X X X X X X
This recycle mark indicates that the packaging conforms to the environmental protection legislation in Germany.
Esta marca de reciclaje indica que el empaquetado conforma a la legislación de protección ambiental en Alemania.
CASIO COMPUTER CO.,LTD.6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, JapanMA0603-A Printed in China
LK100ES1A
C
