USER’S GUIDE GUÍA DEL USUARIO - Support | Home | CASIO · K T1/L T2/R button L SONG MEMORY...

PX310ES1C

ES

USER’S GUIDEGUÍA DEL USUARIOPlease keep all information for future reference.Guarde toda información para tener como referencia futura.

Safety Precautions Before trying to use the piano, be sure to read the separate “Safety Precautions”.

Precauciones de seguridadAntes de intentar usar el piano, asegúrese de leer las “Precauciones de seguridad” separadas.

407A-E-002A

CASIO Europe GmbHBornbarch 10, 22848 Norderstedt, Germany

Important!Please note the following important information before using this product.

• Before using the AD-12 Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefullycheck the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptorthat is seriously damaged.

• The product is not intended for children under 3 years.• Use only CASIO AD-12 adaptor.• The AC adaptor is not a toy.• Be sure to disconnect the AC adaptor before cleaning the product.

IMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade orthe third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electricianfor replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and thepoint where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatuscombination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into theapparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,shall be placed on the apparatus.

The power indicator being unlit does not mean the apparatus is completely disconnected from the MAINS.When you need to have the apparatus completely disconnected from the MAINS, you must unplug the power cord.For that purpose, locate the apparatus in a way that secures easy access to the power cord.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This mark applies in EU countries only.

NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user’s author-ity to operate the equipment.

E-1

Contents

Company and product names used in thismanual may be registered trademarks of others.

407A-E-003A

General Guide ..........................E-2Attachment of the Score Stand .................. E-2

About the FUNCTION button...................... E-3

Numeric Input Keys and +/– Keys .............. E-4

Playing Back All the demo Tunes ............... E-4

Power Supply ...........................E-4Using the AC Adaptor ................................. E-4

Connections .............................E-5Connecting Headphones ............................ E-5

Connecting an audio or musicalinstrument amplifier .................................... E-5

Connecting to a PEDAL Jack ..................... E-6

Playing with Different Tones .....E-7Selecting and Playing a Tone ..................... E-7

Selecting Main Tones and Variation Tones ... E-7

Selecting an Advanced Tone, GM Tone,or Drum Set ................................................ E-7

Adjusting the Brilliance of a Tone ............... E-8

Layering Two Tones .................................... E-8

Assigning Different Tones to the Left andRight Sides of the Keyboard ....................... E-9

Using Tone Effects .................................... E-10

Using the Piano’s Pedals .......................... E-11

Playing Rhythms ....................E-12Using Auto Accompaniment ...................... E-13

Playing Tunes YouDownload from the Internet ....E-16

Practicing a Tune ...................................... E-17

Using Registration Memory ....E-18What is registration memory? ................... E-18

Recording to and Playing Backfrom Song Memory .................E-20

Recording Your Keyboard Play................. E-21

Playing Back from Song Memory ............. E-22

Deleting Song Memory Data .................... E-23

Other Settings ........................E-24Adjusting Accompaniment Volume ........... E-24

Changing the Keyboard Touch ................. E-24

Changing the Piano Key ........................... E-25

Changing the Pitch of the Piano toMatch Another Instrument ........................ E-25

Using Digital Piano Setup Memory ........... E-25

Using MIDI ................................................ E-25

Saving the Song Data You Downloadfrom the Internet ....................................... E-26

Troubleshooting.....................E-28

Specifications.........................E-29

Operational Precautions .......E-30Locating the Unit ....................................... E-30

Care of the Unit ......................................... E-30

Lithium Battery .......................................... E-30

Setting Control Key Chart .....E-31

Appendix ..................................A-1Tone List ..................................................... A-1

Rhythm List ................................................. A-2

Drum Assignment List ................................. A-3

Fingered Chord Chart ................................. A-4

MIDI Implementation Chart

E-2

General Guide

Bottom

Attachment of the Score StandInsert the score stand into the slot at the top of thedigital piano as shown in the illustration.

Left Side Panel

407A-E-004A

6 7 8 9

1

E F GHIJKL M T V WQ RS UN O P

0 A B DC

2 3 4 5

NOTE• Each chapter of this manual starts with an illustration

of the piano’s console, which shows the buttons andother controllers you need to operate.

FUNCTION

VOLUME

Back Panel

E-3

1 PEDAL connector

2 DAMPER PEDAL jack

3 SOFT/SOSTENUTO PEDAL jack

4 LINE OUT R, L/MONO jacks

5 LINE IN R, L/MONO jacks

6 POWER button

7 DC 12V jack

8 MIDI THRU/OUT/IN terminals

9 PHONES jacks

0 RHYTHM/SONG SELECT buttons

A TEMPO buttons

B TONE buttons

C TONE SELECT buttons

D REGISTRATION buttons

E VOLUME knob

F FUNCTION button

G INTRO/ENDING button

General Guide

H SYNCHRO/FILL-IN button

I START/STOP, DEMO button

J RHYTHM, USER SONG button

K T1/L T2/R button

L SONG MEMORY button

M Display screen

N TRANSPOSE buttons

O TUNE buttons

P BRILLIANCE buttons

Q ADVANCED TONES/GM TONES button

R VARIATION button

S SPLIT button

T REVERB, REVERB TYPE button

U CHORUS, CHORUS TYPE button

V BANK button

W STORE button

407A-E-005A

NOTE• Key, button, and other names are indicated in the text of this manual using bold type.

About the FUNCTION buttonThe FUNCTION button makes it possible to perform a variety of useful functions. Note the following generalinformation about using the FUNCTION button.

An indicator lamp above the FUNCTION button flashes while it is depressed. The lamp goes out when yourelease the FUNCTION button.

The FUNCTION button is always used in combination with another button or keyboard key. You hold downthe FUNCTION button as you press another button or keyboard key.• The indicator lamp above the button flashes for a few seconds at high speed to let you know that the setting is complete.

Example: “Adjusting the Brilliance of a Tone” on page E-8

For details about all the keyboard key functions you can perform with the FUNCTION button, see “SettingControl Key Chart” on page E-31.

Flashing Unlit

E-4 407A-E-006A

General Guide

Numeric Input Keys and +/–Keys

For a moment after you hold down the FUNCTIONbutton and then press another button to activate afunction, you can use certain keyboard keys to inputnumbers or to increase (+) and decrease (–) settingvalues.

Since the keyboard keys operate as switches at thistime, notes do not sound when you press keyboardkeys.

See “To adjust the tempo” on page E-12 for an actualexample.

Playing Back All the demo TunesThe following procedure plays back the demo tunesin sequence.

1 While holding down the FUNCTIONbutton, press the DEMO button at the sametime. • This starts sequential playback of the demo

tunes. • You can play along with the demo tunes on the

keyboard, if you want. Tone assigned to thekeyboard is the one that is preset for the demotune that is playing.

2 Press the DEMO button again to stop demotune play.

Power SupplyYou can power this digital piano by plugging it into astandard household power outlet.Be sure you turn off power and unplug the power cordfrom the electrical outlet whenever the digital pianois not in use.

Using the AC AdaptorMake sure that you use only the AC adaptor specifiedfor this digital piano.

Specified AC Adaptor: AD-12

[Left Side Panel]

DC 12V jack

AC adaptor AD-12

AC outlet

Note the following important precautions to avoiddamage to the power cord.

During Use• Never pull on the cord with excessive force.• Never repeatedly pull on the cord.• Never twist the cord at the base of the plug or

connector.• The power cord should not be stretched tight

while it is in use.

During Movement• Before moving the keyboard, be sure to unplug

the AC adaptor from the power outlet.

During Storage• Loop and bundle the power cord, but never wind

it around the AC adaptor.

IMPORTANT!• Make sure that the product is turned off before connecting

or disconnecting the AC adaptor.• Using the AC adaptor for a long time can cause it to

become warm to touch. This is normal and does notindicate malfunction.

E-5

Connections

407A-E-007A

IMPORTANT!• Whenever connecting external equipment, first set the

VOLUME knob of the digital piano and the volumecontroller of the external equipment to relatively lowvolume settings. You can later adjust volume to the levelyou want after connections are complete.

• Be sure also to refer to the documentation that comes withthe external equipment for its proper connectionprocedures.

Connecting HeadphonesConnect commercially available headphones to thedigital piano’s PHONES jacks. This cuts off the built-in speakers, which means you can practice even lateat night without disturbing others. To protect yourhearing, make sure that you do not set the volumelevel too high when using headphones.

[Left Side Panel]

Connecting an audio ormusical instrument amplifier

Connecting to an audio or musical instrumentamplifier provides even clearer, more powerful soundthrough external speakers.

Headphones

PHONES jacks

Playing Output from ExternalEquipment through the Piano’sSpeakers 1LINE IN R jack input sounds through the piano’s rightspeaker, while LINE IN L/MONO jack input soundsthrough the left speaker. Connecting to the LINE INL/MONO jack only causes the same output to beproduced from both speakers. It is up to you topurchase connecting cables that are compatible withthe equipment you are connecting.

Connecting to Audio Equipment 2Use commercially available cables to connect theexternal audio equipment to the piano’s LINE OUTjacks as shown in Figure 2. LINE OUT R jack outputis right channel sound, while LINE OUT L/MONOjack output is left channel sound. It is up to you topurchase connecting cables like the ones shown in theillustration for connection of audio equipment.Normally in this configuration you must set the audioequipment’s input selector to the setting that specifiesthe terminal (such as AUX IN) to which the piano isconnected. Use the piano’s VOLUME knob to adjustthe volume level.

Connecting to a Musical InstrumentAmplifier 3Use commercially available cables to connect theamplifier to the piano’s LINE OUT jacks as shown inFigure 3. LINE OUT R jack output is right channelsound, while LINE OUT L/MONO jack output is leftchannel sound. Connecting to the LINE OUT L/MONO jack only outputs a mixture of both channels.It is up to you to purchase connecting cable like theone shown in the illustration for connection of theamplifier. Use the piano’s VOLUME knob to adjustthe volume level.

Audio amplifier AUX IN, etc.

PIN plugsRIGHT(Red)

LEFT(White)

Guitar amplifier, keyboard amplifier, etc.

INPUT 1

INPUT 2

Standard jacks

Standard plug

Tape recorder, MIDI sound source

E-6

Connecting to a PEDAL JackDepending on the type of operation you want thepedal (SP-3) to perform, connect the pedal’s cable tothe digital piano’s PEDAL DAMPER jack or PEDALSOFT/SOSTENUTO jack. If you want to use bothjacks at the same time, you need to purchase anotheroptionally available pedal.See “Using the Piano’s Pedals” on page E-11 forinformation about using a pedal.

[Back Panel]

PEDAL connectorYou can connect the optionally available Pedal Unit(SP-30) to the PEDAL connector. You can then use thepedals for expression that is similar to that availableon an acoustic piano.

[Bottom]

Accessories and OptionsUse only the accessories and options specified for thisdigital piano. Use of non-authorized items creates thedanger of fire, electric shock, and personal injury.

Connections

SP-3

PEDAL jacks

PEDAL connector

407A-E-008A

E-7

Playing with Different Tones

407A-E-009B

FUNCTION

VOLUME

REVERBVARIATION

CHORUSSPLIT

TONE SELECT

TONE ADVANCED TONES/GM TONES

BRILLIANCE

Selecting and Playing a ToneYour piano has the following types of tones built in.

Main Tones 12

Variation Tones 12

Advanced Tones 40

GM Tones 128

Drum Sets 10

Selecting Main Tones andVariation Tones

1 Press the POWER button.

2 Use the VOLUME knob to adjust thevolume level.

3 Press one of the 12 TONE buttons to selectthe tone you want.• The names of the main tones are marked above

the TONE buttons.Example: To select JAZZ ORGAN

POWER button

4 Press the VARIATION button so theindicator lamp above it is lit.• This selects the variation tone assigned to each

TONE button. Example: CLAVI• For information about variation tone assigned

to each button, see the Tone List on page A-1.

5 To toggle between the main tone(VARIATION indicator lamp off) and variationtone (VARIATION indicator lamp on), pressthe VARIATION button or the TONE button.

NOTE• Changing the main tone, variation tone or

advanced tone selection causes DSP* to switchautomatically to the default setting for the newlyselected tone. This causes any notes that aresounding at the time of the change to be interruptedmomentarily. The DSP* will be set to the defaultsetting for the newly selected tone when the noteresumes. (*See page E-10)

Selecting an Advanced Tone,GM Tone, or Drum Set

You can use the following procedure to assign one ofthe piano’s 40 Advanced Tones, 128 GM tones, or 10drum sets to the ADVANCED TONES/GM TONESbutton.

1 Press the ADVANCED TONES/GM TONESbutton.• This selects the tone that is currently assigned

to the ADVANCED TONES/GM TONESbutton.

• The display continues to display the tune orrhythm number.

2 Use the Tone List on page A-1 to find theadvanced tone, GM tone, or drum setnumber you want.Example: 008 (MARIMBA)

E-8


3 While holding down the FUNCTIONbutton, press the ADVANCED TONES/GMTONES button. Remember to keep theFUNCTION button depressed.• This causes the tone number of the tone that is

currently assigned to the ADVANCED TONES/GM TONES button to appear on the display.

Example: 080 (GM VIOLIN)

4 While holding down the FUNCTIONbutton, use the keyboard keys shown belowto input the tone number of the tone youwant to assign to the ADVANCED TONES/GM TONES button.Example: 008 (MARIMBA)

5 After inputting the tone number you want,release the FUNCTION button to exit theGM tone setting screen.

NOTE• You can also select a tone by holding down the

ADVANCED TONES/GM TONES button as youuse the TONE SELECT [ ] and [ ] buttons toscroll through tone numbers on the display.

• The tone that you assign to the ADVANCEDTONES/GM TONES button is retained until youturn off the keyboard.

• If a drum set is assigned to the ADVANCEDTONES/GM TONES button, keyboard keys sounddrum sounds when you press them. See page A-3for information about the drum sounds that areassigned to each of the keyboard keys.

• This displays the number of the assigned tone.

Selecting the ADVANCED TONES/GMTONES Button Variation ToneTo assign a variation tone to the ADVANCED TONES/GM TONES button, perform the steps under“Selecting an Advanced tone, GM Tone, or Drum Set”on page E-7. After step 1, however, press theVARIATION button so the indicator lamp above it islit.• After you assign a tone as the variation tone, you

can select it by pressing the ADVANCED TONES/GM TONES button.

Adjusting the Brilliance of a ToneYou can adjust the clarity and sharpness of a tone tosuit your music and personal preferences.

1 Holding down the FUNCTION button,press the BRILLIANCE buttons to adjust thebrilliance of a tone to the level that youwant.

[ ] : produces a more mellow sound[ ] : produces a brighter sound

• To return the brilliance setting to its initialdefault, hold down the FUNCTION button andpress both of the BRILLIANCE buttons at thesame time.

Layering Two TonesUse the following procedure to layer to two tones, sothey sound at the same time.Of the two TONE buttons you press to layer two tones,the one on the left is the main tone, while the one onthe right is the layered tone.

PREPARATION• If you plan to use a variation tone, perform the procedure

on page E-7 to select the variation tone for the applicableTONE button(s) before starting this procedure.

407A-E-010A

E-9


407A-E-011A

1 Simultaneously press the TONE buttons ofthe two tones that you want to layer.Example: Press GRAND PIANO 1 button and

STRINGS button at the same time.

• If the layer tone is a variation tone, the indicatorlamp above the VARIATION button will light.

• The tones are now layered.

2 After you are finished using the layeredtones, press the one of the TONE buttonsagain to unlayer them.

NOTE• Note that you cannot layer the main tone and

variation tone assigned to the same TONE button.

Adjusting the Volume Balance betweenTwo Layered Tones

1 While holding down the FUNCTIONbutton, use the keyboard keys shown belowto adjust the volume of the layered tones.

• To return the volume setting to its initial default,hold down the FUNCTION button and pressboth of the keys at the same time.

GRAND PIANO 1

STRINGS

C1

C2

C3

C4

C5

C6

C7

C8

Assigning Different Tones to the Leftand Right Sides of the Keyboard

You can assign different tones to keys on the left sideand the right side of the keyboard.

1 Press the TONE button of the tone you wantto select for the high (right) range.Example: GRAND PIANO 1

2 Press the SPLIT button. • This causes the SPLIT indicator lamp to light.

3 Press the TONE button of the tone you wantto select for the low (left) range. • The keyboard is now split between the two

tones.Example: STRINGS

4 After you are finished using the splitkeyboard, press the SPLIT button again tounsplit it.• This causes the SPLIT indicator lamp to go out.

Specifying the Keyboard Tone Split Point

1 While holding down the SPLIT button,press the keyboard key where you want theleft limit of the high range (right) tone tobe.

NOTE• The split point setting also controls the point where

the keyboard splits between the accompanimentkeyboard (pages E-14, 15) and the melodykeyboard. Moving the split point also affects thesizes of the accompaniment keyboard and themelody keyboard.

Low rangeFlash

Left limit of the high range

High range

Split PointLow Range High Range

STRINGS GRAND PIANO 1

Volume of the main toneVolume of the layered tone

Initial default (Center)

¥£

E-10


407A-E-012B

Using Tone EffectsReverb: Makes your notes resonateChorus: Adds more breadth to your notes

Turning Effects On and Off

1 Each press of the REVERB or CHORUSbutton toggles the setting as shown below.• You can determine the status of the effects by

checking the REVERB and CHORUS indicatorlamps.

Changing the Effect TypeThere are four reverb and four chorus types.

1 Turn on the effect you want to change.

2 While holding down the FUNCTIONbutton, press the REVERB or CHORUSbutton to cycle through the effect typesettings as shown below.

[Reverb]

0: Room 1 1: Room 2 2: Hall 1 3: Hall 2

[Chorus]

About DSPDSP makes it possible to digitally produce complexacoustic effects.The DSP is assigned to each tone whenever you turnon digital piano power.

Turning DSP On and Off

1 While holding down the FUNCTIONbutton, press one of the keyboard keysshown below to turn DSP on or off.

Off:

On:

C1

C2

C3

C4

C5

C6

C7

C8

0: Chorus 1 1: Chorus 2 2: Chorus 3 3: Chorus 4

Lit

Unlit

On

Off

E-11407A-E-013A


NOTE• Under initial default settings, DSP is on for the main

tone, and layer and split are turned off. DSP can beapplied to only one part as shown below.

• You can turn chorus on or off for each main tone,layer tone, and split tone part.

• You cannot turn reverb on or off for each main tone,layer tone, and split tone part.

Using the Piano’s PedalsThe digital piano is equipped with two pedal jacks, onefor a damper pedal and one for a soft/sostenuto pedal.

Pedal functions• Damper Pedal

Pressing the damper pedal while playing will causethe notes you play to reverberate for a very longtime. When GRAND PIANO 1 is selected as thetone, using this pedal causes note to reverberate justlike the pedal on an acoustic grand piano.

• Soft PedalPressing this pedal while playing weakens notesplayed on the keyboard after the pedal was pressed,and makes them sound softer.

• Sostenuto PedalOnly the notes of the keys that are depressed whenthis pedal is pressed are sustained until the pedalis released.

Initial DefaultsLayer Tone DSP OnSplit Tone DSP On

MainToneOnOffOff

LayerToneOffOnOff

SplitToneOffOffOn

SP-3

Selecting the Pedal FunctionA pedal connected to the piano’s PEDAL jack canoperate as either a soft pedal or a sostenuto pedal.When you turn on the keyboard, the pedal is initiallyconfigured for soft pedal operation. You can performthe following operation to select either soft orsostenuto for the pedal operation.

1 While holding down the FUNCTIONbutton, use the keyboard keys shown belowto select either soft or sostenuto.

Adjusting the Effect Applied when theDamper Pedal is Pressed Half Way(With optional SP-30 only)You can specify to what extent the damper effectshould be applied when you press the damper pedalhalf way. A setting in the range of 0 (no effect) to 42(same effect as full press) can be specified.

1 While holding down the FUNCTIONbutton, press one of the keyboard keysshown below to specify the setting youwant.

: Decreases the effect : Increases the effect

• To return the volume setting to its initial default,hold down the FUNCTION button and pressboth of the keys at the same time.

C1C2

C3

C4

C5

C6

C7

C8

C1C2

C3

C4

C5

C6

C7

C8

Sostenuto:

Soft:

E-12

You can select from among 120 built-in rhythms.Rhythms 0 through 109 include percussion instrumentsounds, but rhythms 110 through 119 do not. See thenext page for information about how to use rhythms110 through 119.

1 Press the RHYTHM button so the RHYTHMindicator lamp (above the button) is lit.• Each press of the button toggles between the

upper indicator lamp and lower indicator lamp.

2 While holding down the FUNCTIONbutton, use the keyboard keys shown belowto input a rhythm number.• If you want your accompaniment rhythm to

include percussion instrument sounds, select arhythm in the range of 0 through 109.

3 Press the START/STOP button.• This starts the rhythm.

4 Press the START/STOP button again to stopthe rhythm.

Playing RhythmsNOTE• You can also cycle through the available rhythms

in step 2 by holding down the FUNCTION buttonand pressing the RHYTHM/SONG SELECT [ ]or [ ] button.

• Pressing the two RHYTHM/SONG SELECTbuttons at the same time selects rhythm 0.

To adjust the tempo

1 While holding down the FUNCTIONbutton, use the TEMPO [ ] and [ ]buttons to change the tempo (speed).• To return to its standard tempo setting, press

the TEMPO [ ] and [ ] buttons at the sametime.

NOTE• You can also use keyboard keys to change the tempo

setting.(1) While holding down the FUNCTION button,

press the TEMPO button.(2) While keeping the FUNCTION button

depressed, use the keyboard keys shown belowto input a number.

* Tempo Range: 30 to 255

407A-E-014A

FUNCTIONINTRO/ENDING

START/STOP

TEMPORHYTHM/SONGSELECT

SYNCHRO/FILL-IN

RHYTHM

E-13

Playing Rhythms

407A-E-015A

Using Auto AccompanimentWith auto accompaniment, the keyboardautomatically plays rhythm, bass, and chord parts inaccordance with chords you select using simplifiedkeyboard fingerings, or chords you play. Autoaccompaniment makes it feel like you have your ownprivate backup group with you all the time.

NOTE• Rhythms 110 through 119 consist of chord

accompaniments only, without any drums or otherpercussion instruments. These rhythms do notsound unless CASIO CHORD, FINGERED, orFULL RANGE CHORD is selected as theaccompaniment mode. With such rhythms, makesure that CASIO CHORD, FINGERED, or FULLRANGE CHORD is selected before you try playingchords.

To play with auto accompaniment

PREPARATION• Select the rhythm you want to use and adjust the tempo.

1 Select one of the three chord modes(MODE).

• Here we will select the CASIO CHORD mode.• See page E-14 for information about how to use

the chord modes.

2 Press the SYNCHRO/FILL-IN button.• This configures the piano so rhythm and chord

accompaniment will start automatically whenyou press any keys within the accompanimentkeyboard range.

3 Press the INTRO/ENDING button.• This configures the piano so accompaniment

starts with an intro pattern.

4 Use a CASIO CHORD fingering to play thefirst chord within the accompanimentkeyboard range.• This will cause the intro pattern for the selected

rhythm to play, followed by the autoaccompaniment rhythm and chord pattern.

5 Use CASIO CHORD fingerings to playother chords.• See “How to Play Chords” on page E-14 for

information about how to finger chords withthe various chord modes.

• You can insert a fill-in pattern while an autoaccompaniment is playing by pressing theSYNCHRO/FILL-IN button. A fill-in helps tochange the mood of the auto accompanimentpattern.

6 To stop auto accompaniment play, press theINTRO/ENDING button.• This will play an ending pattern for the selected

rhythm before stopping auto accompanimentplay.

NOTE• You can start or stop auto accompaniment play

without an intro or ending pattern by pressing theSTART/STOP button in steps 3 and 6.

• You can adjust the volume of auto accompaniment.For more information see “AdjustingAccompaniment Volume” on page E-24.

FULL RANGE CHORD:FINGERED:

NORMAL:CASIO CHORD:

E-14

Chord Types

Major chordsPress one accompaniment key.Note that the chord producedwhen you press anaccompaniment keyboard keydoes not change octave,regardless of which key you useto play it.

Minor chords (m)To play a minor chord, keep themajor chord key depressed andpress any other accompanimentkeyboard key located to the rightof the major chord key.

Seventh chords (7)To play a seventh chord, keep themajor chord key depressed andpress any other twoaccompaniment keyboard keyslocated to the right of the majorchord key.

Minor seventh chords (m7)To play a minor seventh chord,keep the major chord keydepressed and press any otherthree accompaniment keyboardkeys located to the right of themajor chord key.

Example

C Major (C)C C DE F# # E F GAA BB C C DE FE#

C minor (Cm)C C DE F# # E F GAA BB C C DE FE#

C seventh (C7)C C DE F# # E F GAA BB C C DE FE#

C minor seventh(Cm7)

C C DE F# # E F GAA BB C C DE FE#

Playing Rhythms

407A-E-016A

NOTE• It makes no difference whether you press black or

white keys to the right of a major chord key whenplaying minor and seventh chords.

FINGEREDIn this mode, you specify chords by playing them as youwould on a piano, inside the accompaniment keyboardrange. To specify a C-chord, you would play C-E-G.

FINGERED Accompaniment Keyboard and MelodyKeyboard

How to Play ChordsThe way you finger chords depends on the currentchord mode.

NormalIn this mode there is no auto accompaniment, so youcan play all of piano’s keys for standard-fingeringchords or melody notes.

CASIO CHORDThis method of chord play makes it possible foranyone to easily play chords, regardless of previousmusical knowledge and experience. The followingdescribes the CASIO CHORD “Accompanimentkeyboard” and “Melody keyboard”, and tells you howto play CASIO CHORDs.

CASIO CHORD Accompaniment Keyboard andMelody Keyboard

IMPORTANT!• The accompaniment keyboard can be used for playing

chords only. No sound will be produced if you try playingsingle melody notes on the accompaniment keyboard.

• The split point (page E-9) is the point that separates theAuto Accompaniment area and the melody area of thekeyboard. You can change the location of the split point,which also changes the sizes of the keyboard areas.

Accompanimentkeyboard Melody keyboard

Chord TypesCASIO CHORD accompaniment lets you play fourtypes of chords with minimal fingering.

Accompanimentkeyboard Melody keyboard

E-15

Playing Rhythms

NOTE• See the “Fingered Chord Chart” on page A-4 for

details on playing chords with other roots.

*1: Inverted fingerings cannot be used. The lowestnote is the root.

*2: The same chord can be played without pressingthe 5th G.

NOTE• Except for the chords specified in note*1 above,

inverted fingerings (i.e. playing E-G-C or G-C-Einstead of C-E-G) will produce the same chords asthe standard fingering.

• Except for the exception specified in note*2 above,all of the keys that make up a chord must bepressed. Failure to press even a single key will notplay the desired FINGERED chord.

FULL RANGE CHORDThis accompaniment method makes it possible to playa total of 38 chord variations: the 15 available withFINGERED plus 23 additional variations. Thekeyboard interprets any input of three or more keysthat matches a FULL RANGE CHORD pattern to be achord. Any multi-key input that is not a FULL RANGECHORD pattern is interpreted as melody play. Becauseof this, there is no need for a separate accompanimentkeyboard, and the entire keyboard from end-to-endcan be used for both melody and chords.

FULL RANGE CHORD Accompaniment Keyboardand Melody Keyboard

Accompaniment keyboard/Melody keyboard

Chords Recognized by This PianoThe following table identifies patterns that arerecognized as chords by FULL RANGE CHORD.

Pattern Type

FINGERED

StandardFingerings

Number of Chord Variations

The 15 chord patterns shown under“FINGERED” on page E-14.

23 standard chord fingerings. Thefollowing are examples of the 23chords available with C as the bassnote.

407A-E-017A

E

E G C

G C

2

1

1 ..... Chord C

2 ..... Chord CCE

Example: To play the chord C major and .

NOTE• If there are more than six semitones between the

lowest note and the next note to the right, the lowestnote is interpreted as a bass note.

CE

IMPORTANT!• The accompaniment keyboard can be used for playing

chords only. No sound will be produced if you try playingsingle melody notes on the accompaniment keyboard.

• The split point (page E-9) is the point that separates theAuto Accompaniment area and the melody area of thekeyboard. You can change the location of the split point,which also changes the sizes of the keyboard areas.

C Cm Cdim

Caug *1 Csus4 C7 *2

Cm7 *2 Cmaj7 *2 Cm7 5

C7 5 *1 C7sus4 Cadd9

Cmadd9 CmM7 *2 Cdim7 *1

C6 • Cm6 • C69

DC

EC

FC

GC

A C

BC

• • • • • • D C

BC

D mC

DmC

FmC

GmC

AmC

BmC

• • • • • •

DdimC

A7C

F7

CFm7

CGm7

C Aadd9

C• • • • •

E-16

You can save music data for up to 10 tunes youdownload from the Internet to the digital piano’s usersong area (No. 0 through 9). Once you store a song indigital piano memory, you can play it back using thefollowing procedure.

1 Press the USER SONG button so the USERSONG indicator lamp (below the button)is lit.• Each press of the button toggles between the

upper indicator lamp and lower indicator lamp.

2 While holding down the FUNCTIONbutton, press the keyboard keys shownbelow to input a tune number.

3 Press the START/STOP button.• This starts the playback of the tune.

4 Press the START/STOP button again to stoptune playback.

Playing Tunes You Download from the InternetNOTE • You can also cycle through the available tunes in

step 2 by holding down the FUNCTION button andpressing the RHYTHM/SONG SELECT [ ] or[ ] button.

• Pressing the two RHYTHM/SONG SELECTbuttons at the same time selects tune 0.

• You cannot use layer or split while playing a tune.

FUNCTION

USER SONG

T1/L T2/RSTART/STOP

RHYTHM/SONG SELECT

407A-E-018A

E-17

Playing Tunes You Download from the Internet

Practicing a TuneYou can turn off the left hand part or right hand partof the user song* and play along on the digital piano.* With song data, the left-hand part is assigned to

MIDI Channel 3, while the right-hand part isassigned to MIDI Channel 4.

PREPARATION• Select the tune you want to practice and adjust the tempo

(See “To adjust the tempo” on page E-12).• The maximum tempo setting for each tune is double the

initial default tempo of the tune.• A number of tunes have tempo changes part way through

in order to produce specific musical effects.

1 Use the T1/L T2/R button to turn parts onor off.• The indicator lamps above the button show the

current on/off status of the parts.

2 Press the START/STOP button.• This starts playback of the tune, without the

part you selected in step 1.

3 Play the missing part on the piano’skeyboard.

4 Press the START/STOP button again to stopsong playback.

407A-E-019A

E-18

Using Registration Memory

What is registration memory?Registration memory lets you save up to 32 (4 areas ×8 banks) digital piano setups (tone, rhythm, tempo,etc.) for instant recall whenever you need them.

Registration Memory Setup DataThe following are the settings that can be saved foreach registration memory setup.

• Tone• Rhythm• Tempo• Layer setting• Split setting• Split point• Effect setting• DSP setting• Brilliance setting• Accompaniment Volume• Transpose setting• Pedal function setting• Damper pedal setting• SYNCHRO/FILL-IN button setting• MODE setting

NOTE• All of the registration memory banks are preset

with default data.• Registration memory functions are disabled while

you are using the User Song, Song Memory ordemo tune function.

How registration memory organizesits dataRegistration memory has four banks, and each bankcontains four areas. Use the BANK button to select abank, and the REGISTRATION buttons to select anarea.

1Each press of the BANK button cycles through thebank numbers, from 1 to 8.

2Pressing a REGISTRATION button (1 to 4) selectsthe corresponding area in the currently selectedbank.

NOTE• Storing a new setup to a registration memory area

replaces the setup that was previous stored there.

21

1-1Bank 1 1-2 1-3 1-4

2-1Bank 2 2-2 2-3 2-4

4-1Bank 4 4-2 4-3 4-4

5-1Bank 5 5-2 5-3 5-4

6-1Bank 6 6-2 6-3 6-4

7-1Bank 7 7-2 7-3 7-4

8-1Bank 8 8-2 8-3 8-4

3-1Bank 3 3-2 3-3 3-4

1 2 3 4

STORE

BANK REGISTRATION

407A-E-020A

E-19

Using Registration Memory

To store a setup in registrationmemory

1 On the digital piano, configure the tone,rhythm, and other settings you want to saveas your setup.• See “Registration Memory Setup Data” (page

E-18) for more information.

2 Use the BANK button to select theregistration memory bank where you wantto save the setup.• This causes the number of the selected bank to

appear on the display for about two seconds. Ifyou do not perform the following step withinthat time, the bank selection screen willdisappear.

Example: Bank 1 selected

WARNING• The following step will replace the setup currently in the

area you select with the new setup. Make sure you do notneed the current setup before performing the next step.

3 While holding down the STORE button,press the REGISTRATION button (1 to 4)that corresponds to the area where youwant to store the setup.• You can also change the bank selection at this

time by pressing the BANK button whileholding down the STORE button.

Example: After button 2 is pressed

4 Release the REGISTRATION and STOREbuttons.

To recall a setup from registrationmemory

1 Use the BANK button to select theregistration memory bank that contains thesetup you want to recall.• This causes the number of the selected bank to

appear on the display for about two seconds. Ifyou do not perform the following step withinthat time, the bank selection screen willdisappear.

2 Press the REGISTRATION button (1 to 4)for the area that contains setup you wantto recall.

NOTE• If you press a REGISTRATION button without

selecting a bank first, the digital piano will recallthe setup from the applicable area in the bank youpreviously last selected.

Registration memory contents are retained evenwhen you turn off digital piano power (pageE-25).

407A-E-021A

E-20

You can store the notes you play in Song Memory forlater playback.

NOTE• You cannot use layer or split with Song Memory

record operation.

TracksThe song memory of this piano records and plays backnotes much like a standard tape recorder. There aretwo tracks, each of which can be recorded separately.Besides notes, each track can be assigned its own tonenumber. During playback you can adjust the tempoto change the speed of playback.

Song Memory Capacity• You can store a total of up to about 10,000 notes

(Track 1 + Track 2) in Song Memory.• Recording stops automatically if the number of

notes in Song Memory exceeds the maximum whileyou are recording. This is indicated by the RECindicator lamp turning off.

Other Song Memory DataThe following data is included when recording to SongMemory: keyboard play, selected tone, tempo setting(Track 1 only), pedal operations, reverb and chorussettings, DSP on/off setting, brilliance setting,accompaniment volume setting, selected rhythm(Track 1 only), chord mode (Track 1 only), and intro/fill-in/ending control (Track 1 only).

Recording to and Playing Back from Song Memory

T1/L T2/R

SONG MEMORYSTART/STOP

INTRO/ENDING

SYNCHRO/FILL-IN

Recorded Data StorageThis digital piano has a lithium battery to supplypower to retain memory contents even while poweris off.* The life of the lithium battery is five years afterthe date of manufacture of the digital piano. Be sureto contact your CASIO service provider about havingthe lithium battery replaced every five years.

* Never turn off piano power while a recordoperation is in progress.

IMPORTANT!• If the data recorded in a single track uses up all the

available Song Memory capacity, you will not be able torecord anything in the other track.

• Recording new data to a track automatically deletes anydata previously stored in that track.

• Turning off power while a record operation is in progressdeletes anything recorded up to that point.

• CASIO COMPUTER CO., LTD. shall not be heldresponsible for any losses by you or any third party dueto loss of data caused by malfunction or repair of thisdigital piano, or by battery replacement.

SONG MEMORY Button OperationEach press of the SONG MEMORY button cyclesthrough the functions shown below.

407A-E-022A

Track 1

Start End

Track 2

Auto Accompaniment(rhythm, bass, chords), melody

Melody

Data recorded in track

PlaybackStandby

RecordStandby Normal

Lit Flash Unlit

E-21


Recording Your Keyboard PlayYou can record to either track with or without playbackof the other track.

To record to one track without playingback the otherWhen recording a different tune to Track 2 afterrecording to Track 1, make sure you carefully read thenotes under steps 1 and 2 before actually performingthe steps.

1 Press the SONG MEMORY button so thePLAY indicator lamp is lit.

• Select the tone and effects you want to use inyour recording, and configure the temposettings.

NOTE• If you are recording a different tune to Track 2 after

recording to Track 1, press the T1/L T2/R buttonto turn off the TRACK 1/ LEFT indicator lamp.

2 Press the SONG MEMORY button so theREC indicator lamp is flashing.

• At this time the TRACK 1/ LEFT indicatorlamp should also be flashing. This indicates thatthe piano is standing by for recording to Track1.

NOTE• If you want to record to Track 2, press the T1/L

T2/R button here. This will cause the TRACK2/RIGHT indicator lamp to flash, which indicates thatthe piano is standing by for recording to Track 2.

• If you want to use a rhythm and/or autoaccompaniment during recording (to Track 1only), select the rhythm and chord mode.

3 Start playing something on the keyboard.• This will automatically start recording.• Actually, there are a variety of different ways

to start the record operation. See “Starting theRecord Operation” below for more information.

4 When you are finished, press the START/STOP button to stop recording.• If you are using a rhythm, you can stop

recording with an ending pattern by pressingthe INTRO/ENDING button.

• Stopping recording causes the REC indicatorlamp to go out, and indicator lamp above thebutton of the track to which you recorded tolight.

• To play back the track you just recorded, pressthe START/STOP button again.

5 After you are finished recording or playingback, press the SONG MEMORY button sothe PLAY lamp or REC lamp turns off.

Starting the Record OperationYou can use any of the following methods to start arecord operation in step 2 of the above procedure.

When recording to Track 1 with rhythm or autoaccompaniment• Press the START/STOP button to start recording.• Press the SYNCHRO/FILL-IN button to put the

piano into synchro start standby. Recording willstart when you finger a chord in theaccompaniment range of the keyboard.

• Press the INTRO/ENDING button to put thepiano into synchro start standby. Recording willstart and an intro pattern will play when youfinger a chord in the accompaniment range of thekeyboard.

407A-E-023C

Unlit Lit

E-22


When recording to Track 1 without rhythm orauto accompaniment• Recording will start as soon as you play anything

on the keyboard.

When recording to Track 2• Press the START/STOP button or play something

on the keyboard to start recording.

To record to a track while playingback from the otherAfter you finish recording, you can play back Track 1and Track 2 at the same time.

Example: To record to Track 2 while playing back thecontents of Track 1


• Select the tone and effects you want to use whilerecording.

2 Press the T1/L T2/R button so TRACK 1/LEFT indicator is lit.

3 Press the SONG MEMORY button again.• This causes the TRACK 1/LEFT indicator lamp

to flash. Press the T1/L T2/R button, so itcauses the TRACK 2/RIGHT indicator lamp toflash, which indicates that the piano is standingby for recording to Track 2.

4 Press the START/STOP button or playsomething on the keyboard to startsimultaneous playback from Track 1 andrecording to Track 2.

5 When you are finished, press the START/STOP button again to stop recording.

Playing Back from Song Memory


2 Use the T1/L T2/R button to select the trackyou want to play back. The indicator lamps above the button show the

currently selected track.• To play back Track 1, the TRACK 1/LEFT

indicator lamp should be lit.• To play back Track 2, the TRACK 2/RIGHT

indicator lamp should be lit.• To play back Track 1 and Track 2, both the

indicator lamps should be lit.

3 Press the START/STOP button.• This starts playback of the track you selected.• You can change the tempo setting as a track is

playing.• You cannot change the tone setting during

playback.• Press the START/STOP button again to stop

playback.

407A-E-024C

E-23


Deleting Song Memory Data

IMPORTANT!• The procedure below deletes all of the data from the

selected track. Note that the delete operation cannot beundone. Check to make sure you really do not need thedata in Song Memory before you perform the followingsteps.

1 Press the SONG MEMORY button so theREC indicator lamp is flashing.

2 Use the T1/L T2/R button to select the trackyou want to delete.• The indicator lamps above the button show the

currently selected track.• To delete Track 1, the TRACK 1/LEFT indicator

lamp should be flashing.• To delete Track 2, the TRACK 2/RIGHT

indicator lamp should be flashing.

3 Hold down the SONG MEMORY buttonuntil the REC indicator lamp stops flashingand remains lit.

4 Press the T1/L T2/R button.• This deletes the selected track and enters the

standby state.

407A-E-025A

E-24

Other Settings

Adjusting AccompanimentVolume

Perform the following operation to change the volumelevel of the rhythm and chord accompaniment.

1 While holding down the FUNCTIONbutton, use the keyboard keys shown belowto raise () or lower () theaccompaniment volume.

: Raises the accompaniment volume : Lowers the accompaniment volume

FUNCTION TRANSPOSE

TUNE

407A-E-026A

C1

C2

C3

C4

C5

C6

C7

C8

Changing the Keyboard TouchThis setting changes the relative touch of the keyboardkeys.

1 While holding down the FUNCTIONbutton, press one of the keyboard keysshown below.

OffWeak (Strong sound is produced even when

relatively light pressure is applied.)NormalStrong (Normal sound is produced even when

relatively strong pressure is applied.)

£C1

£C2

£C3

£C4

£C5

£C6

£C7

£C8

Off:

Weak: Strong:

Normal:

E-25

Other Settings

Changing the Piano KeyUse this setting to raise or lower the overall key of thekeyboard in semitone steps.

1 Holding down the FUNCTION button,press the TRANSPOSE buttons to raise orlower the overall key of the keyboard.

NOTE• To return the piano key to C, hold down the

FUNCTION button and press the TRANSPOSE[ ] and [ ] buttons at the same time.

• After using Transpose to raise the keyboard to ahigh key, notes played at the highest range of thekeyboard may not sound properly for certain tones.

Changing the Pitch of the Pianoto Match Another Instrument

Use this setting to raise or lower the overall pitch ofthe piano. The setting range is plus or minus 50 cents(100 cents = 1 semitone) from the standard pitch ofA4 = 440.0Hz.

1 Holding down the FUNCTION button,press the TUNE buttons to raise or lowerthe overall pitch of the piano.

* Each press of the button changes the current setting byapproximately 1 cents (1/100 semitone).

NOTE• Holding down the FUNCTION button and pressing

the TUNE buttons [ ] and [ ] at the same timereturns tuning to the standard A4 = 440.0Hz.

407A-E-027B

Using Digital Piano SetupMemory

When setup memory is turned on, the digital pianowill remember its setup* whenever you turn it off. Ifyou turn off setup memory, settings will be clearedwhen you turn off the digital piano.

1 While holding down the FUNCTIONbutton, press one of the keyboard buttonsshown below to turn setup memory on oroff.

Using MIDI

What is MIDI?The letters MIDI stand for Musical Instrument DigitalInterface, which is the name of a worldwide standardfor digital signals and connectors that makes it possibleto exchange musical data between musicalinstruments and computers (machines) produced bydifferent manufacturers.

NOTE• For detailed information about MIDI Implementation,

visit the CASIO website at: http://world.casio.com/.

On:

Off:

C1

C2

C3

C4

C5

C6

C7

C8

[ ] : Raise[ ] : Lower

[ ] : Raise[ ] : Lower

Turning off the digital piano while in the rhythmmodeThe next time you turn on the digital piano, non-localcontrol setting (see “Using MIDI” below) will beconfigured in accordance with setup memory.

Turning off the digital piano while in the user songmodeThe next time you turn on the digital piano, thefollowing settings will be configured in accordancewith setup memory.

Rhythm selection, accompaniment volume, keyboardtouch, pedal type, damper pedal setting, layered tonevolume balance, split point, send channel, accompMIDI out

E-26

Other Settings

407A-E-028A

MIDI ConnectionsTo use a computer or other MIDI device to record andplayback the MIDI data produced by this keyboard,you must connect the MIDI IN and MIDI OUTterminals of both devices in order to send and receivedata.There is a third MIDI terminal named MIDI THRU,which passes any MIDI messages received by theMIDI IN terminal on to another device.

MIDI Settings

1Send ChannelUse this setting to specify one of the MIDI channels(1 through 16) as the Send Channel for sendingMIDI messages to an external device.

2Accomp/Song MIDI OutUse this setting to specify whether or not MIDImessages for the piano’s auto accompaniment andsong memory playback should be sent.

3MIDI IN Chord JudgeSpecifies whether chord judge should be performedon accompaniment range MIDI Note On messagesreceived from an external device.

4Local ControlThis setting controls whether or not power is cut offinternally from the piano’s keyboard and soundsource. Turning off Local Control cuts off power tothe keyboard and source, which means that the pianodoes not produce any sound when played. Thiscomes in handy when you want to turn off the piano’skeyboard and use its auto accompaniment feature toaccompany an external sequencer or other device.

MIDI OUT MIDI IN

MIDI IN Otherdevice

Computer etc.

MIDI cable: MK-5

1 While holding down the FUNCTIONbutton, press one the keyboard keys shownbelow to configure the setting you want.

1Send Channel– : Decreases value+: Increases value

2Accomp/Song MIDI OutOffOn

3MIDI IN Chord JudgeOffOn

4Local ControlOffOn

Saving the Song Data YouDownload from the Internet

You can transfer song data from your computer to thedigital piano. You can store up to 10 tunes as user songs0-9. For SMF data you purchase or create, you need touse an SMF Converter to convert it to SMF 0 formatbefore transferring it to the digital piano.

C1

C2

C3

C4

C5

C6

C7

C8

3 On:

Off:

1 +

–

42 On:

Off:

On:

Off:

E-27

To connect to a computerBe sure to turn off the digital piano and your computerbefore connecting them. You should also set thevolume controller of the digital piano to a relativelylow volume.

1 Connect the digital piano’s MIDI interfaceto your computer’s MIDI interface.

2 Turn on the digital piano, and then turn onyour computer or other connected device.

3 Start up the software you want to use onyour computer.

NOTE• Performing a digital piano operation while

transferring data between it and a computer mayinterrupt the data transfer. Do not perform anydigital piano operations while data transfer is inprogress.

Other Settings

CASIO MUSIC SITE

MIDI INMIDI Interface

INOUT

MIDI OUT

InternetServiceProvider

407A-E-029A

To install the SMF Converter

1 On the computer to which you plan toconnect, install the SMF Converter thatcomes on the CD-ROM that comesbundled with the digital piano.• On the CD-ROM, double-click “SMFConv-

e.exe”, and then follow the instructions thatappear on your computer screen to install SMFConverter.

* Before installing SMF Converter, be sure to read thecontents of the “smfreadme.txt” file in each languagefolder on the CD-ROM.

For information about using SMF Converter, double-click “index.html” in the [help] folder, which wascreated when you installed SMF Converter. You canalso access user documentation from the Windows[Start] menu by clicking [Programs] - [CASIO] - [SMFConverter] - [manual].

* A browser that supports frames (like Internet Explorer 4or Netscape Navigator 4.04 or higher) is required to viewthe SMF Converter manual.

Minimum Computer System Requirements* Operating System:Windows 98SEWindows MeWindows XP

* StorageAt least 10MB free HDD space

* MIDI interface

• You can also obtain a copy of the SMF Converterby downloading it at the Web page shown below.After downloading, install the software on yourcomputer.

CASIO MUSIC SITE

http://music.casio.com/

• In addition to the software itself, the CASIO MUSICSITE will also provide you with information aboutits installation and use. You can also find out aboutthe latest news about your digital piano and otherCASIO musical instruments, and much more.

E-28

Troubleshooting

Symptom

No sound produced whenkeyboard keys are pressed.

Keyboard out of tune.

No sound produced by demo tuneplay.

Memory contents deleted.

No sound produced by connectedexternal MIDI sound source whenthe digital piano keys are pressed.

A tone’s quality and volumesounds slightly differentdepending where it is played onthe keyboard.

Possible Cause

1. VOLUME knob set to MIN.

2. Headphones connected to thedigital piano.

3. Local Control turned off.4. Check the current

accompaniment mode setting.Normally, the accompanimentkeyboard will not produce anynote while CASIO CHORD orFINGERED is selected as theaccompaniment mode.

1. The piano key is set to a valueother than C.

2. Incorrect pitch setting of thepiano.

1. VOLUME knob set to MIN.

2. Headphones connected to thedigital piano.

Lithium battery is dead.

1. The digital piano Send Channeldoes not match the SendChannel of the MIDI soundsource.

2. Volume or expression setting ofthe external sound source is setto 0.

Action

1. Move the VOLUME knob moretowards MAX.

2. Disconnect the headphonesfrom the digital piano.

3. Turn on Local control.4. Change the accompaniment

mode to NORMAL.

1. Change the piano key setting toC, or turn the digital pianopower off and then back onagain.

2. Correct the pitch setting, or turnthe digital piano power off andthen back on again.

1. Move the VOLUME knob moretowards MAX.

2. Disconnect the headphonesfrom the digital piano.

Contact your CASIO ServiceProvider for replacement of thelithium battery.

1. Change the Send Channelsettings so they are identical.

2. Change the volume orexpression setting of theexternal sound source to anappropriate value.

Reference

Page E-7

Page E-5

Page E-26Page E-14

Page E-25

Page E-25

Page E-7

Page E-5

Page E-30

Page E-26

See thedocumentationthat comes withthe externalsound source.

407A-E-030B

This is an unavoidable result of the digital sampling process,* and does not indicatemalfunction.* Multiple digital samples are taken for the low range, middle range, and high range of

the original musical instrument. Because of this, there may be a very slight differencein tonal quality and volume between sample ranges.

E-29

SpecificationsModel: PX-310

Keyboard: 88 piano keys (with touch response)

Polyphony: 32 notes, maximum

Tones: 12 panel tones + 12 variation tones + 40 advanced tones + 128 GM tones + 10 drumsets; with layer, split

Digital Effects: Reverb (4 types), Chorus (4 types), DSP, Brilliance

Demo Tunes: Sequential looping of all 3 tunes (Original)

Auto Accompaniment: • Number of Rhythms: 120

• Tempo Range: 30 to 255

• Controllers: START/STOP, INTRO/ENDING, SYNCHRO/FILL-IN

• Modes: Normal, CASIO CHORD, FINGERED, FULL RANGE CHORD

• Accompaniment Volume: Adjustable

User Songs: • Number of Tunes: 10 tunes maximum (Approximately 145 KB*)* Based on 1 KB = 1024 bytes

• Part On/Off: Left hand, right hand

Song Memory: • Operations: Real-time recording, playback

• Capacity: Approximately 10,000 notes (2 tracks total)

• Memory Backup: Built-in lithium battery (Battery Life: 5 years)

Registration Memory: Number of Memory Areas: 32 (4 sets × 8 banks)

Pedals: Damper, Soft/Sostenuto (Selectable)

Other Functions: • Touch: 3 types, off

• Transpose: 1 octave (F to C to F)

• Tuning: A4 = 440.0Hz ±50 cents (adjustable)

MIDI: 16 multi-timbre receive

Input/Output: • Headphones: Stereo mini jacks × 2• Pedal: Standard jacks × 2• LINE OUT (R)(L/MONO): Standard jacks × 2

Output impedance: 2.3kΩOutput voltage: 1.0V (RMS) MAX

• LINE IN (R)(L/MONO): Standard jacks × 2Input impedance: 9.0kΩInput voltage: 200mV

• Power: 12V DC

• MIDI (THRU) (OUT) (IN)

• Pedal connector (for optional SP-30 only)

Speakers: (12cm × 6cm OVAL) × 2 + φ 5cm × 2 (Output: 8.0W + 8.0W)

Power Supply: AC Adaptor: AD-12

Power Consumption: 12V 18W

Dimensions: 132.3 × 27.8 × 13.2cm (52 1/16 × 10 15/16 × 5 3/16 inch)

Weight: Approximately 11.9 kg (26.2 lbs)

• Design and specifications are subject to change without notice.

407A-E-031B

E-30

Operational Precautions

Locating the UnitAvoid the following locations.• Areas exposed to direct sunlight and high humidity• Areas subjected to very low temperatures• Near a radio, TV, video deck, or tuner (unit can

cause interference with audio or video signals)

Care of the Unit• Never use benzene, alcohol, thinner or other such

chemicals to clean the exterior of the unit.• To clean the keyboard, use a soft cloth dampened

with a weak solution of a mild neutral detergentand water. Wring out all excess moisture from thecloth before wiping.

Lithium BatteryThis unit is equipped with a lithium battery to providepower needed to retain memory contents while unitpower is turned off. Should the lithium battery godead, all memory contents will be lost whenever youturn unit power off. The normal life of the lithiumbattery is five years from the time that the battery wasinstalled. Be sure to periodically contact your retaileror authorized service provider to have the lithiumbattery replaced. Note that you will be chargedseparately for lithium battery replacement.

• Note that CASIO COMPUTER CO., LTD. shall notbe held liable for any damages or losses or anyclaims by third parties arising from corruption orloss of data caused by malfunction or repair of theunit, or from battery replacement.

You may notice lines in the finish of the case ofthis product. These lines are the result of themolding process used to shape the plastic of thecase. They are not cracks or breaks in the plastic,and are no cause for concern.

NOTE• Unauthorized reproduction of this manual in its

entirety or in part is expressly forbidden. All rightsreserved.

• CASIO COMPUTER CO., LTD. shall not be heldliable for any damages or losses or any claims bythird parties arising from use of this product or thismanual.

• The contents of this manual are subject to changewithout notice.

407A-E-032A

E-31407A-E-033A

Setting Control Key ChartW

hile

the

FUN

CT

ION

bu

tton

is d

epre

ssed

, the

key

boar

d k

eys

can

be u

sed

to p

erfo

rm a

var

iety

of d

iffe

rent

set

ting

func

tion

s.

•A

val

ue

next

to a

not

e na

me

ind

icat

es th

e re

lati

ve p

osit

ion

of th

e no

te o

n th

e ke

yboa

rd a

s sh

own

belo

w.

C1

C2

C3

C4

C5

C6

C7

C8

Off

Norm

al

Wea

k

Soft

Soste

nuto

Dampe

r Ped

al Sett

ing

Accom

panim

ent V

olum

e

Keybo

ard T

ouch

Pedal

Functi

on

Strong

Norm

al

FINGERED

CASIO C

HORD

0

+

–

1

2

3

4

5

6

7

8

9

Chord

Mod

e

+/–,

Num

ber I

nput

Key

s

+

–

On

Off

On

Off

On

Off

On

Off

On

Off

Accom

p/Son

g MID

I Out

Send

Chann

el

Laye

red

tone

vo

lume

balan

ce

DSP

* Th

e no

tes

of th

e ke

ys s

ound

whe

n pr

esse

d, e

ven

if th

e FU

NC

TIO

N b

utto

n is

dep

ress

ed.

MID

I IN C

hord

Judg

e

Loca

l Con

trol Setu

p Mem

ory

FULL-R

ANGE

C

HORD

*

A-1

Appendix/Apéndice

GM PIANO 1GM PIANO 2GM PIANO 3GM HONKY-TONKGM E.PIANO 1GM E.PIANO 2GM HARPSICHORDGM CLAVIGM CELESTAGM GLOCKENSPIELGM MUSIC BOXGM VIBRAPHONEGM MARIMBAGM XYLOPHONEGM TUBULAR BELLGM DULCIMERGM ORGAN 1GM ORGAN 2GM ORGAN 3GM PIPE ORGANGM REED ORGANGM ACCORDIONGM HARMONICAGM BANDONEONGM NYLON STR.GUITARGM STEEL STR.GUITARGM JAZZ GUITARGM CLEAN GUITARGM MUTE GUITARGM OVERDRIVE GTGM DISTORTION GTGM GT HARMONICSGM ACOUSTIC BASSGM FINGERED BASSGM PICKED BASSGM FRETLESS BASSGM SLAP BASS 1GM SLAP BASS 2GM SYNTH-BASS 1GM SYNTH-BASS 2GM VIOLINGM VIOLAGM CELLOGM CONTRABASSGM TREMOLO STRINGSGM PIZZICATOGM HARPGM TIMPANI

NYLON STR.GUITARSTEEL STR.GUITARJAZZ GUITARCHORUS CLEAN GUITAROVERDRIVE GUITARACOUSTIC BASSRIDE BASSFINGERED BASSANALOG SYNTH-BASSVIOLINHARPSTRING ENSEMBLE80’S SYNTH-STRTRUMPET

Panel Tones/Sonidos de panel55555444443333322222 55555444443333366666

GRAND PIANO 1ROCK PIANOE.GRAND 80ELEC.PIANO 1ELEC.PIANO 260’S ELEC.PIANOROCK ORGANJAZZ ORGANSTRINGSSYNTH-VOICESYNTH-BRASSFANTASY

161632321632321632321616

042454

161749546288

10010048484952515048484948

GRAND PIANO 2DANCE PIANOPIANO PADDYNO ELEC.PIANOFM ELEC.PIANOVIBRAPHONEDRAWBAR ORGANCLAVISYNTH-STRINGSCHOIRSYNTH-PADNEW AGE

321616321632163232161616

1674511167

50529088

100100100494849494848494849

Advanced Tones/Sonidos avanzados11111 55555444443333322222

0123456789

10111213

LA PIANOMELLOW PIANOMODERN PIANOHONKY-TONKOCTAVE PIANOPOP ELEC.PIANOSYNTH-STR E.PIANOHARPSICHORDMARIMBAROTARY DRAWBARROTARY PERC.ORGANOVD ROTARY ORGANCHURCH ORGANCHAPEL ORGAN

3216161616161632323216321632

32589446

121617161919

100100100100100505349485049524950

GM Tones/Sonidos GM11111 55555444443333322222

404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687

323232163216323232321632323232163216161632163216323232323216163232323232323216323232323232323232

0123456789

1011121314151617181920212223242526272829303132333435363738394041424344454647

000000000000000000000000000000000000000000000000

11111 55555444443333322222 11111 555554444433333222221415161718192021222324252627

282930313233343536373839

TROMBONESTEREO BRASSBREATHY ALTO SAXALTO SAXTENOR SAXCLARINETFLUTESAWTOOTH LEADSQUARE LEADWARM PADSPACE VOICESTAR VOICE

3232323232321632323232161632

161616321616321616321616

2425262727323233384046485056

576165656671738180899191

4848484851495048524848495048

494950494949484848484849

888990919293949596979899

100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135

GM STRINGS 1GM STRINGS 2GM SYNTH-STRINGS 1GM SYNTH-STRINGS 2GM CHOIR AAHSGM VOICE DOOGM SYNTH-VOICEGM ORCHESTRA HITGM TRUMPETGM TROMBONEGM TUBAGM MUTE TRUMPETGM FRENCH HORNGM BRASSGM SYNTH-BRASS 1GM SYNTH-BRASS 2GM SOPRANO SAXGM ALTO SAXGM TENOR SAXGM BARITONE SAXGM OBOEGM ENGLISH HORNGM BASSOONGM CLARINETGM PICCOLOGM FLUTEGM RECORDERGM PAN FLUTEGM BOTTLE BLOWGM SHAKUHACHIGM WHISTLEGM OCARINAGM SQUARE LEADGM SAWTOOTH LEADGM CALLIOPEGM CHIFF LEADGM CHARANGGM VOICE LEADGM FIFTH LEADGM BASS+LEADGM FANTASYGM WARM PADGM POLYSYNTHGM SPACE CHOIRGM BOWED GLASSGM METAL PADGM HALO PADGM SWEEP PAD

323232323232321632323232163232163232323232323232323232323216323216161616161616161632161616161632

1616161616163216163232323216323232321632323232323232161632321632

GM RAIN DROPGM SOUND TRACKGM CRYSTALGM ATMOSPHEREGM BRIGHTNESSGM GOBLINSGM ECHOESGM SFGM SITARGM BANJOGM SHAMISENGM KOTOGM THUMB PIANOGM BAGPIPEGM FIDDLEGM SHANAIGM TINKLE BELLGM AGOGOGM STEEL DRUMSGM WOOD BLOCKGM TAIKOGM MELODIC TOMGM SYNTH-DRUMGM REVERSE CYMBALGM GT FRET NOISEGM BREATH NOISEGM SEASHOREGM BIRDGM TELEPHONEGM HELICOPTERGM APPLAUSEGM GUNSHOT

484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495

96979899

100101102103104105106107108109110111112113114115116117118119120121122123124125126127

000000000000000000000000000000000000000000000000

00000000000000000000000000000000

11111 55555444443333322222 11111 55555444443333322222

136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167

Drum Sets/Ajustes de batería

168169170171172173174175176177

11111 555554444422222018

16242530324048

120120120120120120120120120120

STANDARD SET 1STANDARD SET 2ROOM SETPOWER SETELECTRONIC SETSYNTH SET 1SYNTH SET 2JAZZ SETBRUSH SETORCHESTRA SET

Tone List/Lista de sonidos

1 No./No

2 Tone Name/Nombre de sonidos

3 Maximum Polyphony/Polifonía máxima

4 Program Change/Cambio de programa

5 Bank Select MSB/MSB de selección de banco

6 Variation Tones/Sonidos de variación

407A-E-067A

33333––––––––––

A-2 407A-E-068C

Appendix/Apéndice

11111 22222 11111 22222

8 BEAT000 8 BEAT 1001 8 BEAT 2002 8 BEAT 3003 8 BEAT POP 1004 8 BEAT POP 2005 60’S SOUL006 8 BEAT DANCE007 POP ROCK

16 BEAT008 16 BEAT 1009 16 BEAT 2010 16 BEAT 3011 SLOW 16 BEAT012 16 BEAT SHUFFLE 1013 16 BEAT SHUFFLE 2014 FUNK015 LATIN FUSION

POPS016 POP 1017 POP 2018 GUITAR POP019 SOUL020 POP SHUFFLE021 SOUL POP022 WORLD POP023 MELLOW R&B024 60’S POP025 OLDIES POP026 POP WALTZ

BALLAD027 8 BEAT BALLAD 1028 8 BEAT BALLAD 2029 16 BEAT BALLAD 1030 16 BEAT BALLAD 2031 16 BEAT BALLAD 3032 6/8 BALLAD033 ROCK BALLAD034 POP BALLAD035 OLDIES BALLAD036 SERENADE

ROCK037 ROCK 1038 ROCK 2039 R&B040 SHUFFLE ROCK041 60’S ROCK042 SHUFFLE BOOGIE043 BLUES044 TWIST

DANCE045 TRANCE046 RAVE047 TECHNO048 HOUSE049 LATIN HOUSE050 DANCE051 MODERN R&B052 HIP-HOP053 DANCE POP 1054 DANCE POP 2055 DISCO SOUL

JAZZ056 FAST BIG BAND057 MIDDLE BIG BAND058 JAZZ COMBO 1059 SWING060 SLOW SWING061 MODERN JAZZ062 FOX TROT063 QUICKSTEP064 JAZZ WALTZ

EUROPIAN065 POLKA066 POLKA FOX067 POP POLKA068 MARCH 1069 GERMAN MARCH070 WALTZ 1071 WALTZ 2072 VIENNESE WALTZ073 FRENCH WALTZ

LATIN/VARIOUS074 BOSSA NOVA075 SAMBA076 MERENGUE077 CUMBIA078 CHA-CHA-CHA079 BEGUINE080 BOLERO081 MAMBO082 RHUMBA083 TANGO084 REGGAE085 SKA086 LATIN DISCO087 BLUEGRASS088 COUNTRY089 COUNTRY SHUFFLE090 COUNTRY WALTZ091 FAST GOSPEL092 SLOW GOSPEL093 BROADWAY094 DIXIE095 PASODOBLE096 HAWAIIAN097 ADANI098 BALADI099 SYMPHONY

FOR PIANO100 PIANO BALLAD 1101 PIANO BALLAD 2102 PIANO BALLAD 3103 EP BALLAD 1104 EP BALLAD 2105 BLUES BALLAD106 MELLOW JAZZ107 JAZZ COMBO 2108 RAGTIME109 BOOGIE-WOOGIE110 ARPEGGIO 1111 ARPEGGIO 2112 ARPEGGIO 3113 PIANO BALLAD 4114 6/8 MARCH115 MARCH 2116 2 BEAT117 WALTZ 3118 WALTZ 4119 WALTZ 5

Rhythm List/Lista de ritmos1 No./No 2 Rhythm Name/Nombre de ritmo

NOTE• Rhythms 110 through 119 consist of chord accompaniments

only, without any drums or other percussion instruments.These rhythms do not sound unless CASIO CHORD,FINGERED, or FULL RANGE CHORD is selected as theaccompaniment mode. With such rhythms, make sure thatCASIO CHORD, FINGERED, or FULL RANGE CHORDis selected before you try playing chords.

NOTA• Los ritmos 110 al 119 consisten solamente de

acompañamientos de acordes, sin ninguna batería ni otrosinstrumentos de percusión. Estos ritmos no suenan amenos que CASIO CHORD, FINGERED o FULL RANGECHORD sean seleccionados como el modo deacompañamiento. Con tales ritmos, asegúrese de que seselecciona CASIO CHORD, FINGERED o FULL RANGECHORD, antes de tratar de ejecutar los acordes.

A-3407A-E-069A

Appendix/Apéndice

STANDARD SET 1 STANDARD SET 2 ROOM SET—————ROOM KICK 2ROOM KICK 1ROOM SNARE 1ROOM SNARE 2ROOM LOW TOM 2ROOM LOW TOM 1ROOM MID TOM 2ROOM MID TOM 1ROOM HI TOM 2ROOM HI TOM 1——————————————————————————————

C-1

D-1

E-1

F-1

G-1

A-1

B-1

C0

D0

E0

F0

G0

A0

B0

C1

D1

E1

F1

G1

A1

B1

C2

D2

E2

F2

G2

A2

B2

C3

D3

E3

F3

G3

A3

B3

C4

D4

E4

F4

G4

A4

B4

C5

D5

E5

F5

G5

A5

B5

C6

D6

E6

F6

G6

A6

B6

C7

D7

E7

F7

G7

A7

B7

C8

D8

E8

F8

G8

A8

B8

C9

D9

E9

F9

G9

0

2

4

5

7

9

11

12

14

16

17

19

21

23

24

26

28

29

31

33

35

36

38

40

41

43

45

47

48

50

52

53

55

57

59

60

62

64

65

67

69

71

72

74

76

77

79

81

83

84

86

88

89

91

93

95

96

98

100

101

103

105

107

108

110

112

113

115

117

119

120

122

124

125

127

C#-1

E -1

F#-1

A -1

B -1

C#0

E 0

F#0

A 0

B 0

C#1

E 1

F#1

A 1

B 1

C#2

E 2

F#2

A 2

B 2

C#3

E 3

F#3

A 3

B 3

C#4

E 4

F#4

A 4

B 4

C#5

E 5

F#5

A 5

B 5

C#6

E 6

F#6

A 6

B 6

C#7

E 7

F#7

A 7

B 7

C#8

E 8

F#8

A 8

B 8

C#9

E 9

F#9

1

3

6

8

10

13

15

18

20

22

25

27

30

32

34

37

39

42

44

46

49

51

54

56

58

61

63

66

68

70

73

75

78

80

82

85

87

90

92

94

97

99

102

104

106

109

111

114

116

118

121

123

126

ELEC. SET SYNTH SET 1 SYNTH SET 2 JAZZ SET BRUSH SET ORCHESTRA SETPOWER SET—————SYNTH 1 KICK 2SYNTH 1 KICK 1SYNTH 1 RIM SHOTSYNTH 1 SNARE 1SYNTH HAND CLAPSYNTH 1 SNARE 2SYNTH 1 LOW TOM 2SYNTH 1 CHHSYNTH 1 LOW TOM 1SYNTH 1 PHHSYNTH 1 MID TOM 2SYNTH 1 OHHSYNTH 1 MID TOM 1SYNTH 1 HI TOM 2SYNTH 1 CYMBALSYNTH 1 HI TOM 1SYNTH 1 RIDESYNTH 1 TAMBOURINESYNTH 1 COWBELLSYNTH 1 HIGH CONGASYNTH 1 MID CONGASYNTH 1 LOW CONGASYNTH 1 MARACASSYNTH 1 CLAVES——————————————————————————————

—————SYNTH 2 KICK 2SYNTH 2 KICK 1SYNTH 2 SNARE 1SYNTH 2 SNARE 2SYNTH 2 LOW TOM 2SYNTH 2 CHHSYNTH 2 LOW TOM 1SYNTH 2 PHHSYNTH 2 MID TOM 2SYNTH 2 OHHSYNTH 2 MID TOM 1SYNTH 2 HI TOM 2SYNTH 2 CYMBAL 1SYNTH 2 HI TOM 1SYNTH 2 RIDE 1SYNTH 2 CYMBAL 2SYNTH 2 RIDE 2——————————————————————————————

—————ELEC KICK 2ELEC KICK 1ELEC SNARE 1ELEC SNARE 2ELEC LOW TOM 2ELEC LOW TOM 1ELEC MID TOM 2ELEC MID TOM 1ELEC HI TOM 2ELEC HI TOM 1REVERSE CYMBAL——————————————————————————————

Key/ Note number

DRUMS SET LIST

METRONOME CLICKMETRONOME BELLMETRONOME CLICKMETRONOME BELL——LOW TOM 2bLOW TOM 1bMID TOM 2bMID TOM 1bHIGH TOM 2bHIGH TOM 1bCRASH CYMBAL 1aCRASH CYMBAL 1bCRASH CYMBAL 1cCRASH CYMBAL 2aCRASH CYMBAL 2bCRASH CYMBAL 2cRIDE CYMBAL 1aRIDE CYMBAL 1bRIDE CYMBAL 1cRIDE CYMBAL 2aRIDE CYMBAL 2bRIDE CYMBAL 2c———HIGH QSLAPSCRATCH PUSHSCRATCH PULLSTICKSSQUARE CLICKMETRONOME CLICKMETRONOME BELLSTANDARD1 KICK 2STANDARD1 KICK 1SIDE STICKSTANDARD1 SNARE 1HAND CLAP 1STANDARD1 SNARE 2LOW TOM 2CLOSED HI-HATLOW TOM 1PEDAL HI-HATMID TOM 2OPEN HI-HATMID TOM 1HIGH TOM 2CRASH CYMBAL 1HIGH TOM 1RIDE CYMBAL 1CHINESE CYMBALRIDE BELL TAMBOURINESPLASH CYMBALCOWBELLCRASH CYMBAL 2VIBRA-SLAPRIDE CYMBAL 2HIGH BONGOLOW BONGO MUTE HIGH CONGAOPEN HIGH CONGALOW CONGA HIGH TIMBALELOW TIMBALEHIGH AGOGOLOW AGOGO CABASAMARACASSHORT HI WHISTLELONG LOW WHISTLESHORT GUIROLONG GUIROCLAVESHIGH WOOD BLOCKLOW WOOD BLOCKMUTE CUICAOPEN CUICAMUTE TRIANGLEOPEN TRIANGLESHAKERJINGLE BELLBELL TREE CASTANETS MUTE SURDOOPEN SURDOAPPLAUSEAPPLAUSE2——————————————————STANDARD KICK 1aSTANDARD KICK 1bSTANDARD KICK 1cSTANDARD KICK 1dSTANDARD KICK 2aSTANDARD KICK 2bSTANDARD KICK 2cSTANDARD KICK 2dSTANDARD1 SNARE aSTANDARD1 SNARE bSTANDARD1 SNARE cSTANDARD1 SNARE dCLOSED HI-HAT aCLOSED HI-HAT bCLOSED HI-HAT cCLOSED HI-HAT dPEDAL HI-HAT aPEDAL HI-HAT bOPEN HI-HAT aOPEN HI-HAT b

—————STANDARD2 KICK 2STANDARD2 KICK 1STANDARD2 SNARE 1STANDARD2 SNARE 2——————————————————————————————

—————POWER KICK 2POWER KICK 1POWER SNARE 1POWER SNARE 2POWER LOW TOM 2POWER LOW TOM 1POWER MID TOM 2POWER MID TOM 1POWER HI TOM 2POWER HI TOM 1——————————————————————————————

—————BRUSH KICK 2BRUSH KICK 1BRUSH TAPBRUSH SLAPBRUSH SWIRL——————————————————————————————

—————CLOSED HI-HATPEDAL HI-HATOPEN HI-HATRIDE CYMBAL 1JAZZ KICK 1CONCERT BASS DRUMCONCERT SNARECASTANETSCONCERT SNARETIMPANI FTIMPANI F

TIMPANI GTIMPANI ATIMPANI ATIMPANI BTIMPANI BTIMPANI cTIMPANI c

TIMPANI dTIMPANI eTIMPANI eTIMPANI fCONCERT CYMBAL 2CONCERT CYMBAL 1——————————————————————————————

—————JAZZ KICK 2JAZZ KICK 1JAZZ SNARE 1HAND CLAP 2JAZZ SNARE 2——————————————————————————————

Drum Assignment List/Lista de asignación de batería” ” Indicates the same sound as STANDARD SET 1./” ” Indica el mismo sonido que STANDARD SET 1.

A-4

Appendix/Apéndice

407A-E-070A

Fin

ger

ed C

ho

rd C

har

t

Cu

adro

de

aco

rdes

dig

itad

os

(Fin

ger

ed)

dim

m7 5

M7

Mm

7m

7d

im7

Cho

rdTy

peRo

ot C D E F G A B

C /

(D )

(D )

/E

F /(

G )

(G )

/A

(A )

/B

aug

sus4

C D E F G A B

C /

(D )

(D )

/E

F /(

G )

(G )

/A

(A )

/B

m a

dd

97s

us4

mM

77 5

ad

d9

Cho

rdTy

peRo

ot

407A-E-071B

Model PX-310 MIDI Implementation Chart Version: 1.0

Mode 1 : OMNI ON, POLY Mode 2 : OMNI ON, MONO O : YesMode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO X : No

Function ... Transmitted Recognized Remarks

Basic DefaultChannel Changed

DefaultMode Messages

Altered

NoteNumber True voice

Velocity Note ONNote OFF

After Key’sTouch Ch’s

Pitch Bender

ControlChange

ProgramChange :True #

System Exclusive

System : Song PosCommon : Song Sel

: Tune

System : ClockReal Time : Commands

Aux : Local ON/OFF: All notes OFF

Messages : Active Sense: Reset

Remarks

1-161-16

Mode 3X

21-108

O 9nH V = 1-127X 9nH V = 0

XX

X

O 0-127

O

XXX

OO

XXXX

*1: Depends on tone *1: Depende del tono.

**: no relation **: sin relación

1-161-16

Mode 3X

0-1270-127 *1

O 9nH V = 1-127X 9nH V = 0, 8nH V = **

XO

O

O 0-127

O

XXX

XX

XOOX

*2 In accordance with pedal*2 De acuerdo al pedal.

0,321

6,387

10111617181964666771727374767778808182839193

98,99100,101

120121

OXOXXXXXXXO

O*2 O*2

XXXXXXXXXXXXXXOXO

OOOOOOOOOOOOOOOOOOOOOOOOOOOOOO

Bank selectModulationData entryVolumePanExpressionDSP Parameter0DSP Parameter1DSP Parameter2DSP Parameter3DamperSostenutoSoft pedalResonanceRelease TimeAttack TimeBrightnessVibrato rateVibrato depthVibrato delayDSP Parameter4DSP Parameter5DSP Parameter6DSP Parameter7Reverb sendChorus sendNRPN LSB, MSBRPN LSB, MSBAll sound offReset all controller

This recycle mark indicates that the packaging conforms to the environmental protection legislation in Germany.

Esta marca de reciclaje indica que el empaquetado se ajusta a la legislación de protección ambiental en Alemania.

MA0603-C Printed in China PX310ES1C

P

CASIO COMPUTER CO.,LTD.6-2, Hon-machi 1-chome

Shibuya-ku, Tokyo 151-8543, Japan

USER’S GUIDE GUÍA DEL USUARIO - Support | Home | CASIO · K T1/L T2/R button L SONG MEMORY...

Documents

Transcript of USER’S GUIDE GUÍA DEL USUARIO - Support | Home | CASIO · K T1/L T2/R button L SONG MEMORY...