USER’S GUIDE GUÍA DEL USUARIO · 2013. 7. 17. · authorized CASIO Service Provider. AC Adaptor...

45
CTK496/700ES1A ES USER’S GUIDE GUÍA DEL USUARIO

Transcript of USER’S GUIDE GUÍA DEL USUARIO · 2013. 7. 17. · authorized CASIO Service Provider. AC Adaptor...

  • CTK496/700ES1A

    ES

    USER’S GUIDEGUÍA DEL USUARIO

  • 627A-E-002B

    GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas).

    NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.

    FCC WARNINGChanges or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment.

    Important!Please note the following important information before using this product.

    • Before using the optional AD-5 Adaptor to power the unit, be sure to check the AC Adaptorfor any damage first. Carefully check the power cord for breakage, cuts, exposed wire andother serious damage. Never let children use an AC adaptor that is seriously damaged.

    • Never attempt to recharge batteries.• Do not use rechargeable batteries.• Never mix old batteries with new ones.• Use recommended batteries or equivalent types.• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated

    near the battery compartment.• Replace batteries as soon as possible after any sign they are getting weak.• Do not short-circuit the battery terminals.• The product is not intended for children under 3 years.• Use only CASIO AD-5 adaptor.• The AC adaptor is not a toy.• Be sure to disconnect the AC adaptor before cleaning the product.

    CASIO Europe GmbHBornbarch 10, 22848 Norderstedt, Germany

    This mark applies in EU countries only.

  • E-1627A-E-003A

    Safety Precautions

    Congratulations on your selection of the CASIOelectronic musical instrument.• Before using the instrument, be sure to carefully

    read through the instructions contained in thismanual.

    • Please keep all information for future reference.

    SymbolsVarious symbols are used in this user’s guide and onthe product itself to ensure that the product is usedsafely and correctly, and to prevent injury to the userand other persons as well as damage to property.Those symbols along with their meanings are shownbelow.

    DANGERThis symbol indicates information that, if ignoredor applied incorrectly, creates the danger of deathor serious personal injury.

    WARNINGThis indication stipulates matters that have the riskof causing death or serious injury if the product isoperated incorrectly while ignoring this indication.

    CAUTIONThis indication stipulates matters that have the riskof causing injury as well as matters for which thereis the likelihood of occurrence of physical damageonly if the product is operated incorrectly whileignoring this indication.

    Symbol ExamplesThis triangle symbol ( ) means that theuser should be careful. (The example atleft indicates electrical shock caution.)

    This circle with a line through it ( )means that the indicated action must notbe performed. Indications within ornearby this symbol are specificallyprohibited. (The example at left indicatesthat disassembly is prohibited.)

    The black dot ( ) means that theindicated action must be performed.Indications within this symbol are actionsthat are specifically instructed to beperformed. (The example at left indicatesthat the power plug must be unpluggedfrom the electrical socket.)

  • E-2

    DANGER

    Alkaline BatteriesPerform the following steps immediately iffluid leaking from alkaline batteries evergets into your eyes.1. Do not rub your eyes! Rinse them with

    water.2. Contact your physician immediately.Leaving alkaline battery fluid in your eyescan lead to loss of sight.

    WARNING

    Smoke, Strange Odor, OverheatingContinued use of the product while it isemitting smoke, a strange odor, or heatcreates the risk of fire and electric shock.Take the following steps immediately.1. Turn off power.2. If you are using the AC adaptor for

    power, unplug it from the wall outlet.3. Contact your original retailer or an

    authorized CASIO Service Provider.

    AC Adaptor� Misuse of the AC adaptor creates the

    risk of fire and electric shock. Alwaysmake sure you observe the followingprecautions.• Be sure to use only the AC adaptor

    that is specified for this product.• Use only a power source whose

    voltage is within the rating marked onthe AC adaptor.

    • Do not overload electrical outlets andextension cords.

    � Misuse of the AC adaptor’s electric cordcan damage or break it, creating the riskof fire and electric shock. Always makesure you observe the followingprecautions.• Never place heavy objects on the cord

    or subject it to heat.• Never try to modify the cord or subject

    it to excessive bending.• Never twist or stretch the cord.• Should the electric cord or plug

    become damaged, contact youroriginal retailer or authorized CASIOService Provider.

    � Never touch the AC adaptor while yourhands are wet.Doing so creates the risk of electric shock.

    � Use the AC adaptor where it will not besplashed with water. Water creates therisk of fire and electric shock.

    � Do not place a vase or any other containerfilled with liquid on top of the ACadaptor. Water creates the risk of fireand electric shock.

    BatteriesMisuse of batteries can cause them to leak,resulting in damage to nearby objects, or toexplode, creating the risk of fire andpersonal injury. Always make sure youobserve the following precautions.• Never try to take batteries apart or allow

    them to become shorted.• Never expose batteries to heat or dispose

    of them by incineration.• Never mix old batteries with new ones.• Never mix batteries of different types.• Do not charge the batteries.• Make sure the positive (+) and negative

    (–) ends of the batteries are facingcorrectly.

    Do not incinerate the product.Never throw the product into fire.Doing so can cause it to explode, creatingthe risk of fire and personal injury.

    Water and Foreign MatterWater, other liquids, and foreign matter(such as pieces of metal) getting into theproduct create the risk of fire and electricshock. Take the following stepsimmediately.1. Turn off power.2. If you are using the AC adaptor for

    power, unplug it from the wall outlet.3. Contact your original retailer or an

    authorized CASIO Service Provider.

    Disassembly and ModificationNever try to take this product apart ormodify it in any way. Doing so creates therisk of electric shock, burn injury, or otherpersonal injury. Leave all internalinspection, adjustment, and maintenance upto your original retailer or authorizedCASIO Service Provider.

    Safety Precautions

    627A-E-004A

  • E-3

    Dropping and ImpactContinued use of this product after it hasbeen damaged by dropping or subjecting itto strong impact creates the risk of fire andelectric shock. Take the following stepsimmediately.1. Turn off power.2. If you are using the AC adaptor for

    power, unplug it from the wall outlet.3. Contact your original retailer or an

    authorized CASIO Service Provider.

    Plastic BagsNever place the plastic bag the productcomes in over your head or in your mouth.Doing so creates the risk of suffocation.Particular care concerning this precautionis required where small children arepresent.

    Keep off of the product and stand.*Climbing onto the product or stand cancause it to tip over or become damaged.Particular care concerning this precautionis required where small children arepresent.

    LocationAvoid locating the product on an unstablestand, on an uneven surface, or any otherunstable location. An unstable location cancause the product to fall over, creating therisk of personal injury.

    CAUTION

    AC Adaptor� Misuse of the AC adaptor creates the

    risk of fire and electric shock. Alwaysmake sure you observe the followingprecautions.• Do not locate the electric cord near a

    stove or other sources of heat.• Never pull on the cord when

    unplugging from the electrical outlet.Always grasp the AC adaptor whenunplugging.

    � Misuse of the AC adaptor creates therisk of fire and electric shock. Alwaysmake sure you observe the followingprecautions.• Insert the AC adaptor into the wall

    outlet as far as it will go.• Unplug the AC adaptor from the wall

    outlet during lightening storms orbefore leaving on a trip or other long-term absence.

    • At least once a year, unplug the ACadaptor from the wall outlet and wipeaway any dust that is built up in thearea around the prongs of the plug.

    Relocating the ProductBefore relocating the product, alwaysunplug the AC adaptor from the wall outletand disconnect all other cables andconnecting cords. Leaving cords connectedcreates the risk of damage to the cords, fire,and electric shock.

    CleaningBefore cleaning the product, always unplugthe AC adaptor from the wall outlet first.Leaving the AC adaptor plugged in createsthe risk of damage to the AC adaptor, fire,and electric shock.

    BatteriesMisuse of batteries can cause them to leakresulting in damage to nearby objects, or toexplode, creating the risk of fire andpersonal injury. Always make sure youobserve the following precautions.• Use only batteries that are specified for

    use with this product.• Remove batteries from the product if you

    do not plan to use it for a long time.

    Safety Precautions

    627A-E-005B

  • E-4

    ConnectorsConnect only the specified devices andequipment to the product’s connectors.Connection of a non-specified device orequipment creates the risk of fire andelectric shock.

    LocationAvoid the following locations for thisproduct. Such locations create the risk offire and electric shock.• Areas subject to high humidity or large

    amounts of dust.• In food preparation areas or other areas

    subject to oil smoke.• Near air conditioning equipment, on a

    heated carpet, in areas exposed to directsunlight, inside of a vehicle parked inthe sun, or any other area that subjectsthe product to high temperatures.

    Display Screen• Never push on the display screen’s LCD

    panel or subject it to strong impact. Doingso can cause the LCD panel’s glass tocrack, creating the risk of personal injury.

    • Should the LCD panel ever crack orbreak, never touch the liquid inside ofthe panel. LCD panel liquid can causeskin irritation.

    • Should LCD panel liquid ever get insideyour mouth, immediately wash out yourmouth with water and contact yourphysician.

    • Should LCD panel liquid ever get intoyour eyes or onto your skin, rinse withclear water for at least 15 minutes, andthen contact a physician.

    Sound VolumeDo not listen to music at very loud volumesfor long periods. Particular care concerningthis precaution is required when usingheadphones. High volume settings candamage your hearing.

    Heavy ObjectsNever place heavy object on top of theproduct.Doing so can make the product top heavy,causing the product to tip over or the objectto fall from it, creating the risk of personalinjury.

    Safety Precautions

    627A-E-006A

    Correct Stand* AssemblyAn incorrectly assembled stand can tip over,causing the product to fall and creating therisk of personal injury.Make sure you assemble the stand correctly,following the assembly instructions thatcome with it. Make sure you mount theproduct on the stand correctly.

    * Stand is available as an option.

    IMPORTANT!When using batteries, be sure to replace them or shift toone of the alternate power sources whenever you noticeany of the following symptoms.

    • Dim power indicator• Instrument does not turn on• Display that is flickering, dim, or difficult to read• Abnormally low speaker/headphone volume• Distortion of sound output• Occasional interruption of sound when playing at high

    volume• Sudden power failure when playing at high volume• Flickering or dimming of the display when playing at high

    volume• Continued sound output even after you release a key• A tone that is totally different from the one that is selected• Abnormal rhythm pattern and Song Bank play• Loss of power, sound distortion, or low volume when

    playing from a connected computer or MIDI device• Abnormally low microphone volume• Distortion of microphone input• Dim power supply indicator when a microphone is used• Sudden power failure when using the microphone

  • E-5

    Congratulations upon your selection of this CASIO musical instrument. This keyboard provides you with the following featuresand functions.

    ❐ 100 tones• Choose from among orchestral sounds, synthesized sounds, and more.

    ❐ 100 rhythms• 100 versatile rhythms help to add plenty of life to all your keyboard performances.

    ❐ Auto Accompaniment• Simply play a chord and the corresponding rhythm, bass and chord parts play automatically.

    ❐ 100-tune Song Bank• A wide selection of favorites including “ODE TO JOY” and “JINGLE BELLS” is yours for your listening enjoyment or play

    along fun. A simple operation cuts out the melody part or accompaniment part of the tune, allowing you to play along on thekeyboard.

    ❐ Musical Information System• A big LCD screen graphically shows you fingerings, keyboard keys to be pressed, and notes, making keyboard play more

    informative and enjoyable than ever before.

    ❐ MIDI compatibility• Connecting to another MIDI device lets you sound notes on both this keyboard and the connected device by playing on this

    keyboard. You can even playback commercially available pre-recorded MIDI data.

    Introduction

    627A-E-007A

    Avoid heat, humidity or direct sunlight.Do not overexpose the instrument to direct sunlight, or place it near an air conditioner, or in any extremely hot place.

    Do not use near a TV or radio.This instrument can cause video or audio interference with TV and radio reception. If this happens, move the instrument awayfrom the TV or radio.

    Do not use lacquer, thinner or similar chemicals for cleaning.Clean the keyboard with a soft cloth dampened in a weak solution of water and a neutral detergent. Soak the cloth in the solutionand squeeze until it is almost dry.

    Avoid use in areas subjected to temperature extremes.Extreme heat can cause figures on the LCD screen to become dim and difficult to read. This condition should correct itself whenthe keyboard is brought back to normal temperature.

    NOTE• You may notice lines in the finish of the case of this keyboard. These lines are a result of the molding process used to shape

    the plastic of the case. They are not cracks or breaks in the plastic, and are no cause for concern.

    Care of your keyboard

  • E-6 627A-E-008A

    Contents

    Safety Precautions ................ E-1

    Introduction ........................... E-5

    Care of your keyboard .......... E-5

    Contents................................. E-6

    General Guide........................ E-8

    Using the Display ................................... E-10

    Song Bank QuickReference ............................. E-11

    Playing Back a Song Bank Tune ............ E-11

    Power Supply ...................... E-13

    Using batteries ....................................... E-13

    Using the AC Adaptor ............................. E-14

    Auto Power Off ....................................... E-14

    Settings .................................................. E-14

    Connections ........................ E-15

    Phones/Output Terminal ......................... E-15

    Sustain jack Terminal ............................. E-15

    Accessories and Options ....................... E-15

    Basic Operations................. E-16

    Playing the Keyboard ............................. E-16

    Selecting a Tone..................................... E-16

    Using the Microphone Jack .................... E-17

    Auto Accompaniment ......... E-18

    Selecting a Rhythm ................................ E-18

    Playing a Rhythm ................................... E-18

    Adjusting the Tempo............................... E-19

    Using Auto Accompaniment ................... E-19

    Using a Fill-in Pattern ............................. E-21

    Synchro Starting Accompaniment with

    Rhythm Play ........................................... E-21

    Adjusting the Accompaniment Volume ... E-21

    Using the Song Bank .......... E-22

    Playing Back a Song Bank Tune ............ E-22

    Song Bank Mode Display ....................... E-23

    Adjusting the Tempo of a Song Bank

    Tune ....................................................... E-23

    Changing the Tone of a Song Bank

    Tune’s Melody ........................................ E-24

    Playing Along with a Song Bank Tune ... E-24

    Applause Sound ..................................... E-25

    Playing Back All Song Bank Tunes in

    Succession ............................................. E-25

    Using the Chord Book ........ E-26

    Looking Up a Chord Using the Chord

    Book ....................................................... E-27

    Keyboard Settings .............. E-29

    Transposing the Keyboard ..................... E-29

    Tuning the Keyboard .............................. E-29

  • E-7

    Contents

    MIDI ....................................... E-30

    What is MIDI? ........................................ E-30

    General MIDI .......................................... E-30

    Changing MIDI Settings ......................... E-31

    Troubleshooting .................. E-32

    Specifications ...................... E-33

    Appendix ................................ A-1

    Tone List ................................................... A-1

    Note Table ................................................ A-2

    Fingered Chord Chart .............................. A-4

    Percussion Instrument List ....................... A-6

    Rhythm List .............................................. A-7

    MIDI Implementation Chart

    627A-E-009A

  • E-8 627A-E-010A

    CB BA0 D E F *G

    MLKJ

    1 2

    6 84 5 7

    3

    H I

    9

    N O P SQ R

    General Guide

  • E-9

    General Guide

    1 MIC VOLUME knob

    2 Power indicator

    3 MAIN VOLUME buttons

    4 SYNCHRO/FILL-IN button

    5 START/STOP button

    6 POWER/MODE switch

    7 TEMPO buttons

    8 ACCOMP VOLUME button

    9 TRANSPOSE/TUNE/MIDI button

    0 Percussion instrument list

    A CHORD root names

    B Speaker

    C MIC IN jack

    D Rhythm list

    E Tone list

    F Song Bank list

    G Display

    *Attachment of the Score StandInsert both ends of the music stand providedwith the keyboard into the two holes on thetop surface.

    627A-E-011B

    Rear Panel

    T MIDI OUT terminal

    U MIDI IN terminal

    V SUSTAIN jack terminal

    W DC 9V terminal

    X PHONES/OUTPUT terminal

    H [+]/[–] buttons• Negative values can be changed only by using [+] and

    [–] to increase and decrease the displayed value.I Number buttons/Chord specification buttons

    • For input of numbers to change displayed settings.• For input of chord specification data when using the

    Chord Book.

    J TONE button

    K RHYTHM button

    L SONG BANK button

    M STOP button

    N PLAY/PAUSE button

    O REW button

    P FF button

    Q LEFT ON/OFF button

    R RIGHT ON/OFF button

    S CHORD BOOK button

    T U XV W

    • Illustrations in this User ’s Guide shows the CTK-496.

  • E-10 627A-E-012A

    Using the Display

    1. An indicator appears next to the type of setting you are currently performing (TONE, RHYTHM, SONG BANK).

    2. Tone number, rhythm number, song number, keyboard settings value

    3. Rhythm, auto-accompaniment, Song Bank tune beats

    4. Tone name, rhythm name, song name, mode name, keyboard settings name

    5. Musical staff representation of notes and chords you play on the keyboard. A pedal indicator ( ) appears when the keyboard’spedal is depressed. An octave indicator ( ) appears when you play notes in the range from C�6 to C7 to indicate that theiractual notation is one octave higher than that shown on display.

    6. Uses a graphic keyboard to show notes and chords played on the keyboard or played during Song Bank tune playback

    7. Auto-accompaniment, Song Bank, chord book chord names

    8. Dots indicate fingerings during Song Bank playback. “L” and “R” indicate left-hand and right-hand parts.

    9. Rhythm, auto-accompaniment, Song Bank tune tempo

    10. Rhythm, auto-accompaniment, Song Bank tune tempo; volume setting

    11. Song Bank controller indicators

    NOTE• Display examples shown in this User’s Guide are intended for illustrative purposes only. The actual text and values that

    appear on the display may differ from the examples shown in this User’s Guide.

    4

    1

    2 5

    11

    3

    789

    6

    10

    • This is how the display appearswhile the Song Bank is in use.

    General Guide

  • E-11

    Song Bank Quick Reference

    A selection of 100 Song Bank tunes comes built-in for yourlistening pleasure or play along fun. A simple operation cutsout the melody part or accompaniment part of the tune,allowing you to play along on the keyboard. See “Using theSong Bank” on page E-22 for details on playing along withSong Bank tunes.

    Playing Back a Song Bank Tune

    To play back a Song Bank tune

    1 Set the POWER/MODE switch to NORMAL.

    2 Use the MAIN VOLUME buttons to lower thekeyboard volume to a relatively low level.

    3 Press the SONG BANK button to enter the SongBank Mode.

    4 Use the Song Bank list to find the tune you want toplay back, and then use the number buttons to inputthe tune’s two-digit number.Example: To select “68 ODE TO JOY”, input 6 and then 8.

    5 Press the PLAY/PAUSE button to start play of thetune.• The tune plays in an endless loop, re-starting after it

    reaches the end.• The display shows the keyboard keys (on the graphic

    keyboard), fingerings (with the fingering indicators),musical notes (on the staff), and chord names.

    627A-E-013A

    PLAY/PAUSE

    SONG BANKMAIN VOLUME

    POWER/MODE

    Number buttons

    Appears when SONG BANK button is pressed

    Keyboard key used

    Fingers used

    Chord name Staff display

  • E-12 627A-E-014A

    6 Press the RIGHT ON/OFF button to turn off theright-hand melody part and try playing along onthe keyboard.• The display’s graphic keyboard and fingering

    indicators show you the melody notes to play.

    7 Press the RIGHT ON/OFF button again to turn themelody part back on.• You can also turn the accompaniment part on and off

    by pressing the LEFT ON/OFF button.

    8 Press the STOP button to stop playback of the SongBank tune.

    9 Press the TONE button to exit the Song Bank Modeand return to the tone and rhythm selection screen.

    NOTE• You can also perform the following operations during

    play of a Song Bank tune.

    • Pause: Press the PLAY/PAUSE button.• Fast Forward: Press the FF (fast forward) button.• Rewind: Press the REW (rewind) button.

    Song bank Quick Reference

    RIGHT ON/OFFSTOP

    TONE

    indicator turns off

  • E-13

    Power Supply

    This keyboard can be powered by current from a standardhousehold wall outlet (using the specified AC adaptor) or bybatteries. Always make sure you turn the keyboard offwhenever you are not using it.

    Using batteriesAlways make sure you turn off the keyboard before loadingor replacing batteries.

    To load batteries

    1 Remove the battery compartment cover.

    2 Load 6 AA-size batteries into the batterycompartment.• Make sure that the positive (+) and negative (–) ends

    are facing correctly.

    3 Insert the tabs on the battery compartment coverinto the holes provided and close the cover.

    The keyboard may not function correctly if you load or replacebatteries with power turned on. If this happens, turning thekeyboard off and then back on again should return functionsback to normal.

    Important Battery Information

    � The following shows the approximate battery life.Alkaline batteries .................................... 4 hours*Manganese batteries ............................... 2 hours** The above value is standard battery life at normal

    temperature, with the keyboard volume at mediumsetting. Temperature extremes or playing at very loudvolume settings can shorten battery life.

    � Any of the following symptoms indicate low battery power.Replace batteries as soon as possible whenever any ofthe following occurs.• Dim power indicator• Instrument does not turn on• Display that is flickering, dim, or difficult to read• Abnormally low speaker/headphone volume• Distortion of sound output• Occasional interruption of sound when playing at high

    volume• Sudden power failure when playing at high volume• Flickering or dimming of the display when playing at

    high volume• Continued sound output even after you release a key• A tone that is totally different from the one that is

    selected• Abnormal rhythm pattern and Song Bank play• Loss of power, sound distortion, or low volume when

    playing from a connected computer or MIDI device• Abnormally low microphone volume• Distortion of microphone input• Dim power supply indicator when a microphone is used• Sudden power failure when using the microphone

    WARNING

    Misuse of batteries can cause them to leak, resulting indamage to nearby objects, or to explode, creating the risk offire and personal injury. Always make sure you observe thefollowing precautions.• Never try to take batteries apart or allow them to

    become shorted.• Never expose batteries to heat or dispose of them by

    incineration.• Never mix old batteries with new ones.• Never mix batteries of different types.• Do not charge the batteries.• Make sure the positive (+) and negative (–) ends of

    the batteries are facing correctly.

    CAUTION

    Misuse of batteries can cause them to leak resulting indamage to nearby objects, or to explode, creating the risk offire and personal injury. Always make sure you observe thefollowing precautions.• Use only batteries that are specified for use with this

    product.• Remove batteries from the product if you do not plan

    to use it for a long time.

    Tab

    627A-E-015A

  • E-14

    Power Supply

    627A-E-016A

    Using the AC AdaptorMake sure that you use only the AC adaptor specified forthis keyboard.

    Specified AC Adaptor: AD-5

    [Rear Panel]

    Also note the following important warnings and precautionswhen using the AC adaptor.

    WARNING

    Misuse of the AC adaptor creates the risk of fire and electricshock. Always make sure you observe the followingprecautions.• Be sure to use only the AC adaptor that is specified

    for this product.• Use only a power source whose voltage is within the

    rating marked on the AC adaptor.• Do not overload electrical outlets and extension cords.

    • Never place heavy objects on the cord or subject it toheat.

    • Never try to modify the cord or subject it to excessivebending.

    • Never twist or stretch the cord.• Should the electric cord or plug become damaged,

    contact your original retailer or authorized CASIOService Provider.

    • Never touch the AC adaptor while your hands are wet.Doing so creates the risk of electric shock.

    • Use the AC adaptor where it will not be splashed withwater. Water creates the risk of fire and electric shock.

    • Do not place a vase or any other container filled withliquid on top of the AC adaptor. Water creates the riskof fire and electric shock.

    CAUTION

    Misuse of the AC adaptor creates the risk of fire and electricshock. Always make sure you observe the followingprecautions.• Do not locate the electric cord near a stove or other

    sources of heat.

    DC 9V jack

    • Never pull on the cord when unplugging from theelectrical outlet. Always grasp the AC adaptor whenunplugging.

    • Insert the AC adaptor into the wall outlet as far as itwill go.

    • Unplug the AC adaptor from the wall outlet duringlightening storms or before leaving on a trip or otherlong-term absence.

    • At least once a year, unplug the AC adaptor from thewall outlet and wipe away any dust that is built up inthe area around the prongs of the plug.

    IMPORTANT!• Make sure that the keyboard is turned off before

    connecting or disconnecting the AC adaptor.• Using the AC adaptor for a long time can cause it to

    become warm to touch. This is normal and does notindicate malfunction.

    Auto Power OffWhen you are using battery power, keyboard power turnsoff automatically whenever you leave it on withoutperforming any operation for about 6 minutes. When thishappens, use the POWER/MODE switch to turn power backon.

    NOTE• Auto Power Off is disabled (it does not function) when

    you are using the AC adaptor to power the keyboard.

    To disable Auto Power OffHold down the TONE button while turning on the keyboardto disable Auto Power Off.

    NOTE• When Auto Power Off is disabled, the keyboard does

    not turn off automatically no matter how long it is leftwith no operation being performed.

    • Auto Power Off is automatically enabled whenever youturn on keyboard power.

    SettingsAll keyboard settings are returned to their initial defaultswhenever keyboard power is turned back on after beingturned off by operation of the POWER/MODE switch or AutoPower Off.

    AC adapter AD-5

    AC outlet

  • E-15627A-E-017A

    Connections

    Phones/Output TerminalBefore connecting phones or other external equipment, besure to first turn down the volume settings of the keyboardand the connected equipment. You can then adjust volumeto the desired level after connections are complete.

    [Rear Panel]

    White Red PIN plug

    Stereo standard plug

    Audio connection

    PHONES/OUTPUT terminal

    Keyboard amp, guitar amp, etc.

    1

    LEFT RIGHT

    AUX IN or similar terminalof audio amplifier

    2

    3

    Connecting Phones (Figure 1)

    Connecting phones cuts off output from the keyboard’s built-in speakers, so you can play even late at night withoutdisturbing anyone.

    Audio Equipment (Figure 2)

    Connect the keyboard to a audio equipment using acommercially available connecting cord with a standard plugon one end and two PIN plugs on the other end. Note thatthe standard plug you connect to the keyboard must be astereo plug, otherwise you will be able to output only one ofstereo channels. In this configuration, you normally set theinput selector of the audio equipment to the terminal (usuallymarked AUX IN or something similar) where the cord fromthe keyboard is connected. See the user documentation thatcomes with your audio equipment for full details.

    Musical Instrument Amplifier (Figure 3)

    Use a commercially available connecting cord* to connect thekeyboard to a musical instrument amplifier.

    * Be sure to use a connecting cord that has a stereo standardplug on the end you connect to the keyboard, and aconnector that provides dual channel (left and right) inputto the amplifier to which you are connecting. The wrongtype of connector at either end can cause one of the stereochannels to be lost.

    When connected to a musical instrument amplifier, set thevolume of the keyboard to a relatively low level and makeoutput volume adjustments using the amplifier’s controls.

    INPUT 1

    INPUT 2

    PIN jackPIN plug (red)

    PIN plug (white)Stereo standard plug Keyboard or

    guitar amp

    To keyboard’s PHONES/OUTPUT terminal

    Standard plug

    [Connection Example]

    NOTE• You can also connect the keyboard’s MIDI terminal to a

    computer or sequencer. See “MIDI” on page E-30 fordetails.

    Sustain jack TerminalYou can connect an optional sustain pedal (SP-3 or SP-20) tothe SUSTAIN jack terminal to enable the capabilitiesdescribed below.

    Sustain Pedal

    • With piano tones, depressing the pedal causes notes tolinger, much like a piano’s damper pedal.

    • With organ tones, depressing the pedal causes notes tocontinue to sound until the pedal is released.

    Accessories and OptionsUse only the accessories and options specified for thiskeyboard. Use of non-authorized items creates the danger offire, electrical shock, and personal injury.

    SUSTAIN jack Terminal

    SP-20

  • E-16 627A-E-018A

    Basic Operations

    This section provides information on performing basickeyboard operations.

    Playing the Keyboard

    To play the keyboard

    1 Set the POWER/MODE switch to NORMAL.

    2 Use the MAIN VOLUME buttons to lower thekeyboard volume.• It’s always a good idea to set the keyboard volume at

    a relatively low level before playing.• Pressing [�] or [�] causes the current volume setting

    to appear on the display. Press [�] or [�] again tochange the setting.

    3 Play something on the keyboard.

    Selecting a ToneThis keyboard comes with 100 built-in tones. Use thefollowing procedure to select the tone you want to use.

    To select a tone

    1 Find the tone you want to use in the TONE List andnote its tone number.• Not all of the available tones are shown on the tone

    list printed on the keyboard console. For a completelist, see the “Tone List” on page A-1.

    2 Press the TONE button.

    3 Use the number buttons to input the two digit tonenumber for the tone you want to select.Example: To select “26 WOOD BASS”, input 2 and then 6 .

    • Now notes played on the keyboard will be playedusing an acoustical wood bass sound.

    NOTE• Always input both digits for the tone number, including

    a leading zero (if any). If you input one digit and stop,the display will automatically clear your input after a fewseconds.

    • You can also increment the displayed tone number bypressing [+] and decrement it by pressing [–].

    • Sound effect tones such as 77 VEHICLE sound bestwhen you keep a keyboard key depressed.

    Combination tonesThe following describes the two types of combination tonesthat are available.

    Layered Tones (Tone Numbers: 80 through 89)Example: 80 STR PIANO

    This tone layers a strings tone with a piano tone so they bothsound when a keyboard key is pressed.

    Split Tones (Tone Numbers: 90 through 96)Example: 90 BASS/PIANO

    This tone splits the keyboard so one range is assigned a basstone and another range is assigned a piano tone.

    BASS PIANO

    MAIN VOLUMEMIC VOLUME

    POWER/MODE

    TONE Number buttons

    Appears when TONE button is pressed

  • E-17

    Basic Operations

    627A-E-019A

    Percussion soundsExample: 99 PERCUSSION

    This tone assigns various percussion sounds to the keyboard.See the “Percussion Instrument List” on page A-6 for fulldetails.

    Sound Effect TonesWith sound effect tones 77 through 79, the type of soundproduced depends on the octave where the key you press islocated. When 78 PHONE is selected available sound typesare PUSH TONE 1, PUSH TONE 2, RING 1, RING 2, andBUSY SIGNAL.

    PolyphonyThe term polyphony refers to the maximum number of notesyou can play at the same time. The keyboard has 12-notepolyphony, which includes the notes you play as well as therhythms and auto-accompaniment patterns that are playedby the keyboard. This means that when a rhythm or auto-accompaniment pattern is being played by the keyboard, thenumber of notes (polyphony) available for keyboard play isreduced. Also note that some of the tones offer only 6-notepolyphony.

    NOTE• When rhythm or auto accompaniment is playing, the

    number of sounds simultaneously played is reduced.

    Digital SamplingA number of the tones that are available with this keyboardhave been recorded and processed using a technique calleddigital sampling. To ensure a high level of tonal quality,samples are taken in the low, mid, and high ranges and thencombined to provide you with sounds that are amazinglyclose to the originals. You may notice very slight differencesin volume or sound quality for some tones when you playthem at different positions on the keyboard. This is anunavoidable result of multiple sampling, and it is not a signof malfunction.

    Using the Microphone JackConnecting a commercially available microphone to the MICIN jack makes it possible to sing along with the keyboard’sbuilt-in tunes or with output from a MIDI device. Whenconnecting a microphone, be sure to first adjust the MICVOLUME to a relatively low setting, and then adjust to thelevel you want after connecting.

    1 Set the MIC VOLUME knob setting so it is on the“MIN” side.

    2 Turn on the microphone’s ON/OFF switch.

    3 Use the MIC VOLUME knob to adjust microphonevolume to the level you want.

    IMPORTANT!• Be sure to use the microphone’s ON/OFF switch to turn

    off the microphone and to disconnect the microphonefrom the keyboard whenever you are not using it.

    Recommended Microphone Type

    • Dynamic microphone (standard plug)

    IMPORTANT!• Be sure to disconnect the microphone from the keyboard

    whenever you are not using it.

    Howling (Feedback Noise)Any of the following conditions can cause howling (feedbacknoise).

    • Covering the head of the microphone with your hand• Positioning the microphone too near to a speaker

    Should howling occur, try grasping the microphone furtheraway from the head, and move away from any nearbyspeaker.

    Static NoiseFluorescent lighting can cause static noise in the microphonesignal. When this happens, move away from the lighting yoususpect may be causing the static.

    Microphone

    Microphone ON/OFF switch

    MIC VOLUME knob

  • E-18

    Auto Accompaniment

    This keyboard automatically plays bass and chord parts inaccordance with the chords you finger. The bass and chordparts are played using sounds and tones that areautomatically selected to select the rhythm you are using.All of this means that you get full, realistic accompanimentsfor the melody notes you play with your right hand, creatingthe mood of an one-person ensemble.

    Selecting a RhythmThis keyboard provides you with 100 exciting rhythms thatyou can select using the following procedure.

    To select a rhythm

    1 Find the rhythm you want to use in the RHYTHMList and note its rhythm number.• Not all of the available rhythms are shown on the

    rhythm list printed on the keyboard console. For acomplete list, see the “Rhythm List” on page A-7.

    2 Press the RHYTHM button.

    3 Use the number buttons to input the two digitrhythm number for the rhythm you want to select.Example: To select “64 WALTZ”, input 6 and then 4.

    NOTE• “00 CLUB POP” is the initial default rhythm setting

    whenever you turn on keyboard power.• You can also increment the displayed rhythm number

    by pressing [+] and decrement it by pressing [–].

    Playing a RhythmUse the following procedure to start and stop rhythm play.

    To play a rhythm

    1 Set the POWER/MODE switch to NORMAL.

    2 Press the START/STOP button to start play of thecurrently selected rhythm.

    3 To stop rhythm play, press the START/STOP buttonagain.

    NOTE• All of the keyboard keys are melody keys while the

    POWER/MODE switch is set to NORMAL.

    627A-E-020A

    START/STOP TEMPO

    POWER/MODE RHYTHM Number buttons

    Appears when RHYTHM button is pressed

  • E-19

    Auto Accompaniment

    627A-E-021A

    Adjusting the TempoYou can adjust the tempo of rhythm play within a range of20 to 255 beats per minute. The tempo setting is applied toAuto Accompaniment chord play, and song bank operations.

    To adjust the tempo

    1 Use the TEMPO buttons (� / �) to adjust the tempo.� : Increases the tempo value.� : Decreases the tempo value.Example: Hold down the � button until the tempo value

    110 is on the display.

    NOTE• Pressing both TEMPO buttons (� and �) at the same

    time resets the tempo to the default value of the currentlyselected rhythm.

    About the Graphic MetronomeThe graphic metronome appears on the display along withthe tempo value and beat of a rhythm or built-in tune. Thegraphic metronome helps you keep in time as you play alongwith a rhythm or built-in tune.

    Using Auto AccompanimentThe following procedure describes how to use the keyboard’sAuto Accompaniment feature. Before starting, you shouldfirst select the rhythm you want to use and set the tempo ofthe rhythm to the value you want.

    To use Auto Accompaniment

    1 Set the POWER/MODE switch to CASIO CHORDor FINGERED.

    2 Press the START/STOP button to start play of thecurrently selected rhythm.

    3 Play a chord.• The actual procedure you should use to play a chord

    depends on the current POWER/MODE switchposition. Refer to the following pages for details onchord play.

    CASIO CHORD ...............This pageFINGERED ....................... Page E-20

    4 To stop Auto Accompaniment play, press theSTART/STOP button again.

    CASIO CHORDThis method of chord play makes it possible for anyone toeasily play chords, regardless of previous musical knowledgeand experience. The following describes the CASIO CHORD“Accompaniment keyboard” and “Melody keyboard”, andtells you how to play CASIO CHORDs.

    CASIO CHORD Accompaniment Keyboard and MelodyKeyboard

    NOTE• The accompaniment keyboard can be used for playing

    chords only.No sound will be produced if you try playing singlemelody notes on the accompaniment keyboard.

    Basic fingering of current chord(May be different from chord actuallybeing played on the keyboard.)

    Chord name

    Melody keyboardAccompaniment

    keyboardTempo value

    Beat

    Graphic metronome

  • E-20 627A-E-022A

    Auto Accompaniment

    Chord TypesCASIO CHORD accompaniment lets you play four types ofchords with minimal fingering.

    Major chordsMajor chord names are markedabove the keys of theaccompaniment keyboard. Notethat the chord produced when youpress an accompaniment keyboarddoes not change octave, regardlessof which key you use to play it.

    Minor chords (m)To play a minor chord, keep themajor chord key depressed andpress any other accompanimentkeyboard key located to the rightof the major chord key.

    Seventh chords (7)To play a seventh chord, keep themajor chord key depressed andpress any other twoaccompaniment keyboard keyslocated to the right of the majorchord key.

    Minor seventh chords (m7)To play a minor seventh chord,keep the major chord keydepressed and press any otherthree accompaniment keyboardkeys located to the right of themajor chord key.

    CC DE FF# � E #GA�A BB� CC DE FE# �

    CC DE FF# � E #GA�A BB� CC DE FE# �

    CC DE FF# � E #GA�A BB� CC DE FE# �

    CC DE FF# � E #GA�A BB� CC DE FE# �

    C Major (C)

    C minor (Cm)

    C seventh (C7)

    C minor seventh (Cm7)

    NOTE• It makes no difference whether you press black or white

    keys to the right of a major chord key when playing minorand seventh chords.

    FINGEREDFINGERED provides you with a total of 15 different chordtypes. The following describes the FINGERED“Accompaniment keyboard” and “Melody keyboard”, andtells you how to play a C-root chord using FINGERED.

    FINGERED Accompaniment Keyboard and MelodyKeyboard

    Melody keyboardAccompaniment

    keyboard

    NOTE• The accompaniment keyboard can be used for playing

    chords only. No sound will be produced if you try playingsingle melody notes on the accompaniment keyboard.

    C

    Caug *1

    Cm7 *2

    C7�5 *1

    Cmadd9 *2

    Cm

    Csus4

    Cmaj7 *2

    C7sus4

    CmM7 *2

    Cdim

    C7 *2

    Cm7�5

    Cadd9 *2

    Cdim7 *1

    See the “Fingered Chord Chart” on page A-4 for details onplaying chords with other roots.

    *1: Inverted fingerings cannot be used. The lowest note is theroot.

    *2: The same chord can be played without pressing the 5th G.

    NOTE• Except for the chords specified in note*1 above, inverted

    fingerings (i.e. playing E-G-C or G-C-E instead of C-E-G) will produce the same chords as the standardfingering.

    • Except for the exception specified in note*2 above, all ofthe keys that make up a chord must be pressed. Failureto press even a single key will not play the desiredFINGERED chord.

    Chord types Example

  • E-21627A-E-023A

    Auto Accompaniment

    Using a Fill-in PatternFill-in patterns let you momentarily change the rhythmpattern to add some interesting variation to yourperformances.

    The following procedure describes how to use the Fill-infeature.

    To insert a fill-in

    1 Press the START/STOP button to start rhythm play.

    2 Press the SYNCHRO/FILL-IN button to insert a fill-in pattern for the rhythm you are using.

    Synchro Starting Accompanimentwith Rhythm PlayYou can set up the keyboard to start rhythm play at the sametime you play the accompaniment on the keyboard.

    The following procedure describes how to use synchro start.Before starting, you should first select the rhythm you wantto use, set the tempo, and use the POWER/MODE switch toselect the chord play method you want to use (CASIOCHORD, FINGERED).

    To use synchro start

    1 Press the SYNCHRO/FILL-IN button to put thekeyboard into synchro start standby.

    2 Play a chord on the accompaniment keyboard andthe rhythm pattern starts to play automatically.

    NOTE• If the POWER/MODE switch is set to NORMAL, only

    the rhythm plays (without a chord) when you play on theaccompaniment keyboard.

    • To cancel synchro start standby, press the SYNCHRO/FILL-IN button one more time.

    Adjusting the AccompanimentVolumeYou can adjust the volume of the accompaniment parts as avalue in the range of 0 (minimum) to 9.

    1 Press the ACCOMP VOLUME button.

    2 Use the number buttons or the [+]/[–] buttons tochange the current volume setting value.Example: 5

    NOTE• The current accompaniment volume value that appears

    in Step 1 automatically clears from the display if you donot input anything within about five seconds.

    • Pressing [+] and [–] buttons at the same timeautomatically sets an accompaniment volume of 7.

    Flash

    Current accompaniment volume setting

    SYNCHRO/FILL-IN

    ACCOMP VOLUME [+]/[-]

    START/STOP

    Number buttons

  • E-22 627A-E-024A

    Using the Song Bank

    A selection of 100 Song Bank tunes comes built-in for yourlistening enjoyment or play along fun. You can turn off theleft-hand or right-hand part to practice with the remainingpart, and the display even shows you what keys to press andwhich fingers you should use.

    Playing Back a Song Bank Tune

    To play back a Song Bank tune

    1 Set the POWER/MODE switch to NORMAL,FINGERED, or CASIO CHORD.

    2 Adjust the main volume and accomp volume.

    3 Press the SONG BANK button to enter the SongBank Mode.

    4 Use the Song Bank list to find the tune you want toplay back, and then use the number buttons to inputthe tune’s two-digit number.Example: To select “50 ALOHA OE”, input 5 and

    then 0.

    NOTE• “00 MY HEART WILL GO ON (“TITANIC” THEME)” is

    the initial default Song Bank tune setting whenever youturn on keyboard power.

    • You can also increment the displayed tune number bypressing [+] and decrement is by pressing [–].

    • Before advancing to the next step, which actually startsplayback, you can adjust the tempo (page E-19), selecta tone (page E-16) for the melody part, or turn off theleft-hand or right-hand part (page E-24).

    5 Press the PLAY/PAUSE button to start play of thetune.

    6 Press the STOP button to stop playback of the SongBank tune.

    Song NameSong Number

    A l o h a Oe

    Appears when SONG BANK button is pressed

    Appears when PLAY/PAUSE button is pressed

    Keyboard keys used

    Fingers used

    Staff displayChord name

    PLAY/PAUSESTOP

    REWFF

    TEMPO

    SONG BANKPOWER/MODE Number buttons

  • E-23

    Using the Song Bank

    627A-E-025A

    To pause Song Bank tune play

    1 While a Song Bank tune is playing, press the PLAY/PAUSE button to pause it.

    2 To resume play, press PLAY/PAUSE again.

    To fast reverse during playback

    1 While playback is in progress, hold down the REWbutton.

    • Beeps sound during fast reverse to give you an ideaof where you are located in the tune.1 beep: indicates a change to anther measure.2 beeps: indicates the beginning of the tune.

    2 To resume normal playback, release the REWbutton.

    To fast forward during playback

    1 While playback is in progress, hold down the FFbutton.

    • Beeps sound during fast forward to give you an ideaof where you are located in the tune.1 beep: indicates a change to anther measure.3 beeps: indicates the ending of the tune.

    2 To resume normal playback, release the FF button.

    NOTE• Each time you select a new Song Bank tune, the tone,

    tempo, and rhythm that is programmed for the tune areautomatically selected. You can change a tune’s toneand tempo during playback, but you cannot change therhythm.

    • You can also adjust the accompaniment volume(page E-21) for tunes 00 through 80.

    Song Bank Mode DisplayIn the Song Bank Mode, the display shows a variety ofinformation about the tune being played.

    [Playback Display]

    NOTE• Chord names are not displayed for Songs 81 through

    99.

    Adjusting the Tempo of a SongBank Tune

    To change the tempo of a Song Banktune

    The tempo can be set within a range of 20 to 255 beats perminute. The tempo setting can be adjusted while the tune isstopped, playing back, or paused.

    1 Use the TEMPO buttons [�/�] to adjust the tempo.� : each press increases the value� : each press decreases the value

    The indicator “ II ” appears while atune play is paused.

    The indicator “��” appears while afast reverse operation is in progress.

    The indicator “��” appears while afast forward operation is in progress.

    Tune tempo

    Notes played Fingers used

    Keyboard keys used Chord name

    Staff display

  • E-24

    Using the Song Bank

    627A-E-026A

    NOTE• Pressing both the [�] and [�] TEMPO buttons at the

    same time returns the tempo setting to the preset valuefor the currently selected tune.

    • Song Bank tunes 81 through 99 are arranged so theirtempos change part way through the tunes. If you usethe above procedure to change the tempo setting whileone of these tunes is playing, however, the tempo youset is used for the entire tune without any change partway through.

    Changing the Tone of a Song BankTune’s MelodyYou can select any one of the keyboard’s 100 tones to be usedto play the melody part of a Song Bank tune. The tone settingcan be changed while the tune is stopped or playing back.

    1 While a song is playing back, press the TONEbutton.

    2 Find the tone you want in the Tone List, and thenuse the number buttons or the [+] and [–] buttonsto specify the tone number.Example: To select “30 VIOLIN”, input 3 and then 0.

    NOTE• Pressing both the [+] and [–] buttons at the same time

    selects “00 PIANO 1”.• With two-hand tunes (81 to 99), you can select tones

    for both the left hand part and right hand part.• To return a Song Bank tune to its original settings, simply

    select that tune again.

    Playing Along with a Song BankTuneEach Song Bank tune has a left-hand (accompaniment) partand a right-hand (melody) part. You can turn off the left-handpart or right-hand part of a Song Bank tune and play alongwith the remaining part on the keyboard.

    To play along with a Song Bank tune

    1 Perform steps 1 through 4 under “To play back aSong Bank tune” on page E-22 to select the songyou want to play along with.

    2 Press the RIGHT ON/OFF or LEFT ON/OFF buttonfor the part you want to turn off.• Press the RIGHT ON/OFF button to turn off the right

    hand (melody) part, or the LEFT ON/OFF button toturn off the left hand (accompaniment) part.

    • The on/off status of each part is indicated by letters(L and R) that appear inside the hand graphics on thedisplay. A part is turned on when its letter isdisplayed, and turned off when its letter is notdisplayed.

    Melody

    Left-hand notes

    Auto-accompaniment

    Auto-accompaniment

    (percussion, bass,chords)

    TuneNumbers

    AccompanimentType

    Left-handPart

    Right-handPart

    00 to 80

    Piano Solo

    81 to 99

    Right-hand notes

    LEFT ON/OFFRIGHT ON/OFF

    RHYTHM

    PLAY/PAUSESTOP

    [+]/[-]

    Number buttonsTONE

  • E-25

    Using the Song Bank

    627A-E-027A

    Applause SoundWhenever you turn off the left hand or right hand part of aSong Bank tune and play it back, an applause sound isproduced when the tune reaches the end.

    To turn off the applause sound

    1 Press the STOP button and the LEFT ON/OFF orRIGHT ON/OFF button at the same time.

    • Pressing the STOP button and the LEFT ON/OFF orRIGHT ON/OFF button at the same time again turnsthe applause sound back on.

    Playing Back All Song Bank Tunesin Succession

    1 Use the TONE or RHYTHM button to change toany mode other than the Song Bank Mode.• Make sure a dot is not on the display next to the SONG

    BANK indicator.

    2 Press the PLAY/PAUSE button to start playback ofthe Song Bank tunes starting from tune 00.

    3 To stop Song Bank tune playback, press the STOPbutton.• Pausing playback automatically cancels consecutive

    playback of all Song Bank tunes. Re-starting playbackcauses repeat playback of the current tune only.

    3 Press the PLAY/PAUSE button to start play of theSong Bank Tune.• Only the part (melody or accompaniment) that is

    turned on is played, so you can play the other part onthe keyboard.

    • The keys you should press are indicated on thedisplay’s graphic keyboard.

    • You can press the RIGHT ON/OFF and LEFT ON/OFF buttons to turn parts on and off while playbackis in progress.

    4 To end playback, press the STOP button.

    Auto-accompaniment Tunes (Tune Numbers 00 to 80)During playback of these tunes in the Song Bank Mode, thechord specification method for the left hand is alwaysFINGERED for these tunes, regardless of the POWER/MODEswitch setting.

    Two-hand Tunes (Tune Numbers 81 to 99)During playback of these tunes in the Song Bank Mode, theentire keyboard functions as a melody, regardless of thePOWER/MODE switch setting.

    NOTE• With two-hand tunes (81 to 99), you cannot turn off both

    the left-hand and right-hand parts at the same time.Turning off a part causes the other part to turn onautomatically.

    • The selected Song Bank tune continues to repeat untilyou stop playback by pressing the STOP button.

    • The accompaniment volume setting (page E-21) affectsauto-accompaniment tunes (00 to 80) only.

    • Chord names are not displayed during playback of two-hand tunes (81 to 99).

    • Turning off both the left-hand and right-hand parts ofthe auto-accompaniment tunes (00 to 80) results inobbligato accompaniment being played.

    Indicator turns off.

  • E-26

    Using the Chord Book

    627A-E-028A

    The Chord Book feature of this keyboard makes it possiblefor you to look up information about chords quickly andeasily. Simply input the name of the chord and the keyboardkeys you should press, the fingers you should use, and thenotes that make up the chord appear on the display alongwith the chord name.

    What is a chord?A chord is made up of a root note, upon which is stacked anumber of other notes. A variety of different chords can becreated by changing the notes stacked onto a root.

    Chord NamesChords are named using upper-case letters from A throughG, which indicate the root note of the chord. If the root noteis a sharp or flat, the chord itself is sharp or flat. A chordname may also be followed by a degree number or othersymbols that indicate certain characteristics about the chord.

    ���� ��� Stacked notesRoot

    Major seventh Sus fourthSeventh

    RootRoot Degree

    Degree

    Root Root Root Root Root

    Root

    Sharp Flat MinorSharp

    Diminished

    Inverted FormsThere are a number of different ways to play the same chord.A form that is different from the basic form but still producesthe same chord is called an “inverted form.”

    All of the following are C chords.

    Black keys

    White keysB

    ���������� � � � � � � � �C

    C (D )

    E (D )

    F (G ) A (G ) B (A )

    D E F G A C

    � � � ���� � � �

    Sharps and flats can be referred to using either ofthe names shown here. The names in the upperrow of this illustration are used by this keyboard,because they are the names that are mostcommonly used in musical notation.

    ����� ��������� ���

    CLEAR CHORD BOOK

    Chord specification buttons

  • E-27

    Using the Chord Book

    627A-E-029A

    Looking Up a Chord Using theChord Book

    1 Press the CHORD BOOK button to enter the ChordBook mode.

    2 Press the CLEAR button.• This step is necessary to clear any previously input

    chord name.

    3 If the chord name you plan to input is a non-majorchord, use the chord specification buttons to specifythe chord type.• Chord types are indicated by the small letters above

    the chord specifications buttons.• Non-major chords include minor, seventh, sustained,

    etc. chords.• See page E-28 for details on the chord specification

    buttons.• Skip step 3 if you want to input a major chord name.

    4 Press the accompaniment keyboard key thatcorresponds to the root note of the chord.• A dash appears in place of the chord name if the chord

    cannot be recognized by the keyboard.• To specify F�, for example, press the F� key.• The key you press is indicated on the graphic

    keyboard and the corresponding chord sounds.

    5 Check to make sure that the chord name on thedisplay is the one you want. If it isn’t, repeat theabove from step 2.

    6 If the chord is correct, you can see its fingering onthe graphic keyboard. Try playing the chord on thekeyboard.

    NOTE• The fingering that appears on the display is one standard

    fingering. You can also use other fingerings to matchthe size of your hands or to make it easier to progressfrom or to neighboring chords.

    • You can also use the [+] and [–] buttons to change thedisplayed chord name.

    • The tone used to sound chords you play on theaccompaniment keyboard while using the Chord Bookis the same tone used by the accompaniment part ofthe rhythm that was selected before you entered theChord Book mode. Depending on the rhythm that wasselected, some of the notes that make up a chord maybe omitted when you play the chord on theaccompaniment keyboard in the Chord Book Mode. Thisis due to the internal chord conversion function,arrangements, and polyphony limitations. Because ofthis, you should always play the chords indicated on thedisplay on the melody keyboard (the range that doesnot have chord names printed above the keys).

    C D E F G A B C D E FC�E � F �A � B � C� E �

    Keyboard keys used

    Chord name

    Staff display

    Fingers used

  • E-28 627A-E-030A

    Using the Chord Book

    Chord Name Modifier Keys

    ChordType

    Symboland

    NameReference

    ModifierKey

    major

    minor

    aug

    sus 4

    dim

    7th

    M7

    minor 7

    minor M7

    minor 7-5

    C(C major)

    Cm(C minor)

    Caug(C augmened)

    Csus4(C sustainedforth)

    Cdim(C diminished)

    C7(C seventh)

    CM7(C majorseventh)

    Cm7(C minorseventh)

    CmM7(C minorMajorseventh)

    Cm7-5(C minorseventh flatfive)

    C+5

    Cmaj7 C∆7

    ChordType

    Symboland

    NameReference

    ModifierKey

    7sus 4

    add 9

    m add 9

    7th-5

    dim7

    C7sus4(C seventhsus fourth)

    Cadd9(C add ninth)

    Cm add9(C minor addninth)

    Cs7-5(C seventhflat five)

    Cdim7(C diminishedseventh)

    C7�5

    NOTE• Since the chord fingerings that appear on the display

    are selected to allow chord play within theaccompaniment keyboard, inverted chord forms (pageE-26) are often suggested. Inverted chord forms areuseful to help you learn how to play chord variationsthat make it possible to move from one chord to anotherwith minimal hand movement. These forms come inhandy when using FINGERED Auto Accompanimentplay.

    • While a chord name is on the display, you can presskeys on the accompaniment keyboard to find out thefingerings of the same chord with a different root.

    • You can also scroll through chord names using the [+]and [–] buttons.

    • Chord fingerings that appear on the display are formedusing only the keys within the range of theaccompaniment keyboard (leftmost 18 keys). Chordsthat cannot be formed using the keys within this rangeare not displayed.

  • E-29627A-E-031B

    Keyboard Settings

    Transposing the KeyboardTranspose lets you raise and lower the overall key of thekeyboard in semitone units. If you want to play anaccompaniment for a vocalist who sings in a key that’sdifferent from the keyboard, for example, simply usetranspose to change the key of the keyboard.

    To transpose the keyboard

    1 Press the TRANSPOSE/TUNE/MIDI button until thetranspose screen appears on the display.

    2 Use [+] and [–] to change the transpose setting ofthe keyboard.Example: To transpose the keyboard five semitones

    upwards.

    NOTE• The keyboard can be transposed within a range of –6 to +5.• The default transpose setting is “0” when keyboard

    power is turned on.• If you leave the transpose screen on the display for about

    five seconds without doing anything, the screen isautomatically cleared.

    • The transpose setting also affects Auto Accompaniment.• Playing back a Song Bank tune automatically returns

    the transpose setting to its standard default of “0”.• The allowable pitch range you can transpose within

    depends on the tone you are using. If a transposeoperation causes a note to be outside of the pitch rangefor the tone being used, the keyboard automatically playsthe same note in the nearest octave that falls within thepitch range of the tone you are using.

    TRANSPOSE/TUNE/MIDI [+]/[-]

    Tuning the KeyboardThe tuning feature lets you fine tune the keyboard to matchthe tuning of another musical instrument.

    To tune the keyboard

    1 Press the TRANSPOSE/TUNE/MIDI button twice todisplay the tuning screen.

    2 Use [+] and [–] to change the tuning setting of thekeyboard.Example: To lower the tuning by 20.

    NOTE• The keyboard can be tuned within a range of –50 cents

    to +50 cents.*100 cents is equivalent to one semitone.

    • The default tuning setting is “00” when keyboard poweris turned on.

    • If you leave the tuning screen on the display for aboutfive seconds without doing anything, the screen isautomatically cleared.

    • The tuning setting also affects Auto Accompaniment.• Playing back a Song Bank tune automatically returns

    the tuning setting to its standard default of “00”.

  • E-30 627A-E-032A

    What is MIDI?The letters MIDI stand for Musical Instrument DigitalInterface, which is the name of a worldwide standard fordigital signals and connectors that makes it possible toexchange musical data between musical instruments andcomputers (machines) produced by different manufacturers.

    MIDI Connections

    General MIDIGeneral MIDI standardizes MIDI data for all sound sourcetypes, regardless of manufacturer. General MIDI specifiessuch factors as tone numbering, drum sounds, and availableMIDI channels for all sound sources. This standard makes itpossible for all MIDI equipment to reproduce the samenuances when playing General MIDI data, regardless of themanufacturer of the sound source.Though the sound source of this keyboard is not GeneralMIDI compatible, you can still connect the keyboard to acomputer or other MIDI equipment to playback General MIDIdata that is widely available in stores, over computernetworks, and from other sources.

    NOTE• General MIDI data made up of a large number of parts

    may not play correctly on this keyboard.• You will have most success playing back General MIDI

    data that has few parts and is made up of data onchannels 1, 2, 3, 4, and 10.

    MessagesThere is a wide variety of messages defined under the MIDIstandard, and this section details the particular messages thatcan be sent and received by this keyboard.

    MIDI

    NOTE ON/OFFThis message sends data when a key is pressed (NOTE ON)or released (NOTE OFF).A NOTE ON/OFF message include a note number (to indicatenote whose key is being pressed or released) and velocity(keyboard pressure as a value from 1 to 127).NOTE ON velocity is always used to determine the relativevolume of the note. This keyboard does not receive NOTEOFF velocity data.Whenever you press or release a key on this keyboard, thecorresponding NOTE ON or NOTE OFF message is sent byconstant velocity from the MIDI OUT terminal.

    NOTE• The pitch of a note depends on the tone that is being

    used, as shown in the Note Table on page A-2. Wheneverthis keyboard receives a note number that is outside itsrange for that tone, the same tone in the nearestavailable octave is substituted.

    MIDI IN MIDI OUT MIDI IN MIDI OUT

    Computer or other MIDI device

    PROGRAM CHANGEThis is the tone selection message. PROGRAM CHANGE cancontain tone data within the range of 0 to 127.A PROGRAM CHANGE message (0 to 99) is sent out throughthis keyboard’s MIDI OUT terminal whenever you manuallychange its tone number. Receipt of a PROGRAM CHANGEmessage from an external machine changes the tone settingof this keyboard (this page).This keyboard can send tone data within the range of 00 to99 and receive tone data within the range of 0 to 127.

    PITCH BENDThis message carries pitch bend information for smoothlysliding the pitch upwards or downwards during keyboardplay. This keyboard does not send pitch bend data, but is canreceive such data.

    CONTROL CHANGEThis message adds effects such as vibrato and volume changesapplied during keyboard play.CONTROL CHANGE data includes a control number (toidentify the effect type) and a control value (to specify theon/off status and depth of the effect).The following is a list of data that can be received usingCONTROL CHANGE.

    Effect Control Number

    VOLUME 7

    HOLD1 * 64

    MODULATION 1

    * Pressing the foot pedal causes the sustain effect (HOLD1)to be sent (control number 64).

  • E-31

    MIDI

    Changing MIDI SettingsThis keyboard lets you change the settings of two MIDIparameters: TONE MAP and KEYBOARD CHANNEL.

    To change MIDI parameters

    1 Press the TRANSPOSE/TUNE/MIDI button eitherthree or four times to select the parameter you want.

    Press the TRANSPOSE/TUNE/MIDI button threetimes: KEYBOARD CHANNEL.Press the TRANSPOSE/TUNE/MIDI button four times:TONE MAP.Example: To select the TONE MAP parameter.

    2 Use [+] and [–] to change the setting of theparameter.Example: To change the TONE MAP parameter value to

    “G” (GM).

    • If you accidentally go past parameter you want, keeppressing the TRANSPOSE/TUNE/MIDI button untilparameter you want reappears on the display.

    • If you leave the parameter selection screen on thedisplay for about five seconds without doinganything, the parameter selection screen isautomatically cleared.

    627A-E-033A

    TRANSPOSE/TUNE/MIDI [+]/[-]

    Parameters and Their Displays� KEYBOARD CHANNEL (Basic Channel) (Default: 01)This parameter specifies the keyboard MIDI message sendchannel.

    � TONE MAP G/N (Default: N)N: This setting specifies the normal tone map, which allows

    receipt of a program change value in the range of 0 to 99.Only tones that correspond to the 100 built-in tones of thiskeyboard can be played, and tone numbers outside thisrange are ignored.

    G: This setting specifies the General MIDI tone map, whichallows receipt of a program change value in the range of 0to 127. Each of the 128 General MIDI tones is automaticallyassigned to one of the keyboard’s 100 built-in tones asshown on page A-2. Select this setting when you want tolisten to General MIDI data from a computer or otherexternal equipment.

    NOTE• Playing a Song Bank tune causes all MIDI parameters

    to revert to their default settings.• Song Bank data cannot be sent as MIDI data.• MIDI messages cannot be received while the keyboard

    is in the Song Bank Mode.

  • E-32

    Problem Possible Cause See pageAction

    No keyboard Sound

    Any of the following symptoms whileusing battery power.

    Auto Accompaniment does not sound.

    The key or tuning does not matchwhen playing along with anotherinstrument.

    Missing Song Bank tune.

    No sound is produced when playingMIDI data from a computer.

    The bass notes of General MIDI databeing played back by a computer areone octave too low.

    Playing on the keyboard produces anunnatural sound when connected to acomputer.

    Static noise when a microphone isconnected.

    No microphone sound

    1. Power supply problem.

    2. Power is not turned on.

    3. Volume setting is too low.

    4. The POWER/MODE switch is inthe CASIO CHORD or FINGEREDposition.

    Low battery power

    Auto accompaniment volume is set to0.

    The tuning or transpose parameter isset to a value other than 0 or 00.

    1. Left-hand or right-hand part isturned off.

    2. Accompaniment volume is set to 0.

    MIDI cables are not connectedproperly.

    TONE MAP is turned “N”.

    The computer’s MIDI THRU functionis turned on.

    1. Use of a microphone that is adifferent from the type that isrecommended.

    2. Use of the microphone in thevicinity of fluorescent lighting.

    1. Microphone volume setting is toolow.

    2. Microphone on/off switch is set toOFF.

    PagesE-13, 14

    Page E-16

    Page E-16

    Page E-16

    PagesE-13, 14

    Page E-21

    Page E-29

    Page E-24

    Page E-21

    Page E-30

    Page E-31

    See thedocumentationthat comeswith yourcomputer orsequencer.

    Page E-17

    Page E-17

    Page E-17

    Page E-17

    Troubleshooting

    1. Correctly attach the AC adaptor,make sure that batteries poles (+/–)are facing correctly, and check tomake sure that batteries are notdead.

    2. Set the POWER/MODE switch tothe NORMAL position.

    3. Use the MAIN VOLUME buttons toincrease volume.

    4. Normal play is not possible on theaccompaniment keyboard while thePOWER/MODE switch is set toCASIO CHORD or FINGERED.Change the POWER/MODE switchsetting to NORMAL.

    Replace the batteries with a set of newones or use the AC adaptor.

    Use the ACCOMP VOLUME button toincrease the volume.

    Change the transpose or tuningparameter value to 0 or 00.

    1. Check the display to see if theindicator for one of the parts is notdisplayed. If so, press the part’sbutton (LEFT ON/OFF, RIGHTON/OFF) to turn it on.

    2. Adjust accompaniment volume.

    Connect MIDI cables properly.

    Change TONE MAP parameter to “G”.

    Turn off the MIDI THRU function onthe computer or turn off LOCALCONTROL on the keyboard.

    1. Use a recommended typemicrophone.

    2. Move the microphone away fromsource of the static.

    1. Increase the microphone volumesetting.

    2. Change the microphone on/offswitch setting to ON.

    627A-E-034A

    • Dim power indicator• Instrument does not turn on• Display that is flickering, dim, or difficult to read• Abnormally low speaker/headphone volume• Distortion of sound output• Occasional interruption of sound when playing at high

    volume• Sudden power failure when playing at high volume• Flickering or dimming of the display when playing at

    high volume• Continued sound output even after you release a key

    • A tone that is totally different from the one that isselected

    • Abnormal rhythm pattern and Song Bank play• Loss of power, sound distortion, or low volume when

    playing from a connected computer or MIDI device• Abnormally low microphone volume• Distortion of microphone input• Dim power supply indicator when a microphone is

    used• Sudden power failure when using the microphone

  • E-33

    Specifications

    Model: CTK-496/CTK-700

    Keyboard: 61 standard-size keys, 5 octaves

    Tones: 100

    Polyphony: 12 notes maximum (6 for certain tones)

    Auto AccompanimentRhythm Patterns: 100Tempo: Variable (236 steps, = 20 to 255)Chords: 2 fingering methods (CASIO CHORD, FINGERED)Rhythm Controller: START/STOP, SYNCHRO/FILL-INAccomp Volume: 0 to 9 (10 steps)

    Song BankTunes: 100Controllers: PLAY/PAUSE, STOP, REW, FF, LEFT ON/OFF (ACCOMP), RIGHT ON/OFF

    (MELODY)

    DisplayName display: TONE, RHYTHM, SONG BANK name/number, keyboard settings name/valueTempo: Tempo value, metronome, synchro standby, beat indicator, volume settingChord: Chord name, Chord formFingering: Fingering indicators, partsSong Bank Status: PLAY, PAUSE, REW, FFStaff: 5 octaves with sharp and flat indications, pedal symbol, octave symbolKeyboard: 5 octaves

    MIDI: 5 multi-timbre receive

    Other FunctionsTranspose: 12 steps (–6 semitones to +5 semitones)Tuning: Variable (A4 = approximately 440Hz ±50 cents)Volume: 0 to 9 (10 steps)

    TerminalsMIDI Terminals: IN, OUTSustain Terminal: Standard jackPhones/Output Terminal: Stereo standard jack (Output is monaural.)

    Output Impedance: 78ΩOutput Voltage: 4V (RMS) MAX

    Power Supply Terminal: 9V DCMicrophone In: Standard jack (with microphone volume knob)

    Input impedance: 40kΩInput sensitivity: 10mV

    Power Supply: Dual power supply systemBatteries: 6 AA-size batteriesBattery Life: Approximately 4 hours continuous operation on alkaline batteries

    Approximately 2 hours continuous operation on manganese batteriesAC Adaptor: AD-5Auto Power Off: Turns power off approximately 6 minutes after last key operation. Enabled

    under battery power only, can be disabled manually.

    Speaker Output: 2.0W + 2.0W

    Power Consumption: 9V 7.7W

    Dimensions: 95.6 x 35.4 x 13.2 cm (37 11/16 × 13 15/16 × 5

    3/16 inch)

    Weight: Approximately 3.8kg (8.4lbs) (without batteries)

    627A-E-035B

  • A-1

    Appendix/Apéndice

    627A-E-071A

    Tone ListLista de sonidos

    PIANO00 PIANO 101 PIANO 202 HONKY-TONK03 STUDIO PIANO04 ELEC PIANO 105 ELEC PIANO 206 ELEC PIANO 307 ELEC PIANO 408 HARPSICHORD09 CLAVELECTROORGAN10 ELEC ORGAN 111 ELEC ORGAN 212 ELEC ORGAN 313 ELEC ORGAN 414 CHURCH ORGAN15 PIPE ORGAN16 REED ORGAN17 ACCORDION18 BANDONEON19 HARMONICAGUITAR/BASS20 GUT GUITAR21 ACOUS GUITAR22 JAZZ GUITAR23 ELEC GUITAR24 MUTE GUITAR25 DIST GUITAR26 WOOD BASS27 ELEC BASS28 SLAP BASS29 BANJOSTRINGS/ENSEMBLE30 VIOLIN31 CELLO32 HARP33 STRINGS 134 STRINGS 235 STRINGS 336 SYNTH-STR 137 SYNTH-STR 238 CHOIR39 VOICE OOH

    BRASS40 TRUMPET41 TUBA42 BRASS ENS43 FR.HORN 144 FR.HORN 245 BRASS 146 BRASS 247 SYN-BRASS 148 SYN-BRASS 249 SYN-BRASS 3REED/PIPE50 SOPRANO SAX51 ALTO SAX52 TENOR SAX53 OBOE54 CLARINET55 PICCOLO56 FLUTE57 RECORDER58 PAN FLUTE59 WHISTLESYNTH-SOUND I60 SYN-LEAD 161 SYN-LEAD 262 SYN-LEAD 363 SYN-CALLIOPE64 SYN-PAD 165 SYN-PAD 266 SYN-PAD 367 GLASS HMCA68 COUNTRY FARM69 SYN-BASSSYNTH-SOUND II70 PEARL DROP71 COSMIC SOUND72 SOUNDTRACK73 SPACE PAD74 VOICE BASS75 APPLAUSE76 SYNTH-SFX77 VEHICLE78 PHONE79 FUNNY

    LAYER80 STR PIANO81 STR E.PIANO82 CHOIR E.P83 CHOIR ORGAN84 STR GUITAR85 STR HARP86 BRASS STR87 VIB PAD88 12 STR GTR89 CHOIR STRSPLIT/PERCUSSION90 BASS/PIANO91 BASS/E.PIANO92 BASS/VIB93 BASS/GUT GTR94 V.BASS/OOH95 STR/PIANO96 STR/TRUMPET97 VIBRAPHONE98 MARIMBA99 PERCUSSION

  • A-2

    Appendix/Apéndice

    627A-E-072A

    Note TableTabla de notas

    00 12 A 00001 12 A 00102 6 A 00303 6 A 00204 12 A 00405 12 A 00506 6 A 00807 6 A 00908 12 A 00609 12 A 007

    (1) (2) (3) (4)

    10 12 A 01611 12 A 01712 12 A 01813 6 A 01514 12 A 01915 6 A 10416 12 A 02017 6 A 02118 12 A 02319 12 A 022

    (1) (2) (3) (4)

    20 12 A 02421 12 A 02522 12 A 02623 12 A 02724 12 A 02825 12 A 029, 030, 031, 08426 12 B 03227 12 B 033, 034, 03528 12 B 036, 03729 12 A 105

    (1) (2) (3) (4)

    30 12 A 040, 04131 12 B 042, 04332 12 A 045, 046, 04733 12 A 048, 05534 12 A 04935 6 A 04436 12 A 05037 6 A 05138 12 A 091, 05239 12 A 053

    (1) (2) (3) (4)

    40 12 A 05641 12 B 05842 6 A 05743 12 B 06044 6 B 05945 12 B 06146 6 B 06947 12 B 06248 6 B 063, 08349 6 B 070

    (1) (2) (3) (4)

    50 12 A 06451 12 A 06552 12 A 066, 06753 12 A 06854 12 A 07155 12 C 07256 12 A 07357 12 A 074, 07958 12 A 075, 076, 07759 12 A 078

    (1) (2) (3) (4)

    60 12 A 08761 6 A 081, 08662 12 A 08063 6 A 08264 6 A 08965 6 A 09066 6 A 09567 6 A 092, 093, 09868 6 A 054, 085, 09469 12 B 038

    (1) (2) (3) (4)

    70 6 A 09671 6 A 10372 6 A 09773 6 A 10174 12 B 03975 12 D 126, 12776 6 A 10277 6 D 12578 12 D 12479 6 D 123

    (1) (2) (3) (4)

    80 6 A 10681 6 A 088, 10782 6 A 10883 6 A 10984 6 A 099, 11085 6 A 11186 6 B 11287 6 A 11388 6 A 11489 6 A 115

    (1) (2) (3) (4)

    90 12 E 100, 11691 6 E 11792 12 E 11893 12 E 11994 12 E 12095 12 E 12196 12 E 12297 12 A 010, 011, 01498 12 A 012, 01399 12 D

    (1) (2) (3) (4)

    (1): Tone number(2): Maximum polyphony(3): Range type(4): Corresponding General MIDI Number

    (1): Número de sonido(2): Polifonía máxima(3): Tipo de gama(4): Correspondiente al número de la MIDI general

  • A-3

    Appendix/Apéndice

    627A-E-073B

    • See the illustration below for a description of range types (A through E).• Corresponding General MIDI numbers are General MIDI numbers in effect when the tone map setting is “G”.

    • Vea la ilustración siguiente para una descripción de los tipos de gama (A a E).• Los números de la MIDI general correspondiente son los números de la MIDI general que se encuentran en efecto cuando el

    ajuste del mapa de sonidos es “G”.

    ........Range in which same note is played in nearest octave as a result of transpose and MIDI data receive operation.

    ........Gama en la que la misma nota se ejecuta en la octava más cercana como un resultado de la transposición y operación de recepción de datos MIDI.

    ........Range of keyboard play

    ........Gama de ejecución de teclado*1 With received MIDI data, notes are played one octave lower.*1 Con los datos MIDI recibidos, las notas se ejecutan en una octava inferior.

    *2 With received MIDI data, notes are played one octave higher.*2 Con los datos MIDI recibidos, las notas se ejecutan en una octava más alta.

    ........Playable range(using transpose or MIDI receive)

    ........Gama ejecutable (usando la transposición o recepción MIDI)

    Range TypeTipo de gama C-1

    A(Standard type)(Tipo estándar)

    E(SPLIT)

    (División)

    D(Sound Effect)

    (Efecto de sonido)

    C9C8C7C6C5C4C3C2C1C0 A0 A1 A2 G9

    C*2

    �� �� �

    ��

    ���

    A=440Hz

    No scale for tones.Sin escala para los sonidos.

    Scale changes in accordance with tone.La escala cambia de acuerdo con el sonido.

    “55 PICCOLO”only

    Solamente“55 PICCOLO”

    B*1Low pitch

    instrumentsInstrumentos

    de alturatonal baja

  • A-4

    Appendix/Apéndice

    627A-E-074A

    Fingered Chord ChartCuadros de acordes FingeredThis table shows the left-hand fingerings (including inverted forms) for a number ofoften-used chords. These fingering indications also appear on the keyboard’s display.Chords marked with asterisk (*) cannot be played in the Fingered Mode on thiskeyboard.

    Esta tabla muestra las digitaciones (incluyendo las formas invertidas) para varios delos acordes más a menudo usados. Estas indicaciones de digitación también aparecensobre la presentación del teclado.En este teclado, los acordes marcados con asterisco (*) no pueden ejecutarse en elmodo de digitación.

    1234

    5

    : Left hand fingernumbers

    : Números de losdedos de la manoizquierda

    M m 7 m7 dim7

    C

    D

    E

    F

    G

    A

    B

    C (D )

    ��

    F (G )

    ��

    E (D )

    ��

    A (G )

    ��

    B (A )

    ��

    Chord Type

    Root

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 2, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 3, 2, 1]

    *

    *

    *

    M7 m7-5 dim[5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

    [5, 3, 2]

  • A-5

    Appendix/Apéndice

    627A-E-075A

    aug sus4

    C

    D

    E

    F

    G

    A

    B

    C (D )

    ��

    F (G )

    ��

    E (D )

    ��

    A (G )

    ��

    B (A )

    ��

    Chord TypeRoot

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 3, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    [5, 3, 1] [5, 2, 1]

    [5, 2, 1]

    [5, 2, 1]

    *

    *

    7 sus4 m add9 m M7 7-5 add9[5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 4, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [4, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 3, 2, 1]

    [5, 4, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [4, 3, 2, 1]

    [5, 4, 2, 1] [4, 3, 2, 1]

    [4, 3, 2, 1]

    [5, 3, 2, 1]

  • A-6 627A-E-076A

    Appendix/Apéndice

    Percussion Instrument ListLista de instrumentos de percusión• PERCUSSION (tone 99) assigns 39 percussion sound to the keyboard as illustrated below.

    The sound assigned to each key are indicated above the keyboard.

    • PERCUSSION (sonido 99) asigna 39 sonidos de percusión al teclado como se ilustra debajo.Los sonidos asignados a cada tecla se indican sobre el teclado.

    *

    * No sound is produced when the keys in this range arepressed.

    * Cuando se presionan las teclas en esta gama no se produceningún sonido.

    LOW TIMBALE

    HIGH AGOGO

    LOW AGOGO

    CABASA

    MARACAS

    V VOICE BASS DRUM

    V VOICE SNARE

    V VOICE CLOSED HI-HAT

    V VOICE OPEN HI-HAT

    COWBELL

    CRASH CYMBAL 2

    CLAVES

    RIDE CYMBAL 2

    HIGH BONGO

    LOW BONGO

    MUTE HIGH CONGA

    OPEN HIGH CONGA

    LOW CONGA

    HIGH TIMBALE

    OPEN HI-HATLM

    LOW-MID TOMHM

    HIGH-MID TOM

    CRASH CYMBAL 1H

    HIGH TOM

    RIDE CYMBAL 1

    CHINESE CYMBAL

    RIDE BELL

    TAMBOURINE

    SPLASH CYMBAL

    BASS DRUM

    SIDE STICK

    ACOUSTIC SNARE

    HAND CLAP

    ELECTRIC SNAREL

    LOW FLOOR TOM

    CLOSED HI-HATH

    HIGH FLOOR TOM

    PEDAL HI-HATL

    LOW TOM

  • A-7

    Appendix/Apéndice

    627A-E-077A

    POPS I00 CLUB POP01 VOCAL POP02 RAP POP03 FUNKY POP 104 SOUL BALLAD05 POP BALLAD06 LOVE BALLAD07 FUNKY POP 208 EPIC BALLAD09 LITE POPPOPS II10 16 BEAT SHFL11 16 BEAT POP12 16 BEAT FUNK13 8 BEAT POP14 8 BEAT SOUL15 8 BEAT SHFL16 DANCE POP 117 DANCE POP 218 POP FUSION19 FOLKIE POPROCK I20 ROCK WALTZ21 SLOW ROCK 122 SLOW ROCK 223 SOFT ROCK 124 SOFT ROCK 225 SOFT ROCK 326 POP ROCK 127 POP ROCK 228 50’S ROCK29 60’S SOULROCK II30 4 BEAT ROCK31 ROCK32 HEAVY ROCK33 8 BEAT ROCK34 STRAIGHT ROCK35 HEAVY METAL36 TWIST37 NEW ORLNS R&R38 CHICAGO BLUES39 R&B

    Rhythm ListLista de ritmos

    JAZZ/FUSION40 BIG BAND41 SLOW SWING42 SWING43 FOX TROT44 JAZZ WALTZ45 MODERN JAZZ46 COOL47 HARD BOP48 ACID JAZZ49 LATIN FUSIONDANCE/FUNK50 VOCAL GROOVE51 RAVE52 CLUB GROOVE53 TECHNO54 TRANCE55 HOUSE56 GROOVE SOUL57 DISCO58 RAP59 FUNKEUROPEAN60 POLKA 161 POLKA 262 MARCH 163 MARCH 264 WALTZ65 VIENNESE WALTZ66 FRENCH WALTZ67 SLOW WALTZ68 SERENADE69 TANGO 1LATIN I70 BOSSA NOVA71 SAMBA72 MAMBO73 RHUMBA74 CHA-CHA-CHA75 MERENGUE76 REGGAE77 BOLERO78 TANGO 279 LAM