User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA...

10
Waterproof GPS Tracker User Manual Please read this manual carefully before attempting installation and online activation. Pictures are for indication and illustration purposes only.

Transcript of User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA...

Page 1: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

Waterproof GPS TrackerUser Manual

Please read this manual carefully before attempting installation and online activation. Pictures are for indication and illustration purposes only.

Page 2: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

1.Product Functions1.1 Functions

Geo-fence Power-off alert Vibration alert

Movement alert GPS tracking History playback

1.2 Specifications

01 02

GSM 850/900/1800/1900 MHz

GPRS Class 12, TCP/IP

Memory

Location accuracy

Battery

Standby time

Dimension

32+32MB

<10 meters

Cold start≤35sec

450mAh/3.7V Li-Polymer battery

80hr standby time; 7hr working time

87.0(L)*74.0(W)*18.7(H)mm

GPS

TTFF (open sky)

Dust-waterproof level

Working voltage/current

Operating temperature

Weight

MTK high sensitivity chip

Hot start≤1sec

Ip65

9-90VDC/7mA(60VDC)

-20℃-70℃

93.5g

2.Interface descriptions

GSM indicator

Power/Status indicator

GPS indicator

SIM card slot

2.1 Functions

2.2 Accessories

Pictures are for indication and illustration purposes only.

NOTE: After opening the packing box, please check if the accessories are complete. If there is anything missing, please contact your distributor.

Page 3: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

2.3 LED indicator

03 04

Status

Quick flashing

Slow flashing

Dark

Fully charged

No battery/troubleshoot

Solid Red Charging

3.Installation3.1 Placement

The terminal should be placed under cover. It is recommended to ask professionals to install the terminal for you.

2.3.1 Red LED(Power/status indicator)

Definition

Low battery

Status

Quick flashing

Slow flashing

Dark

GPS is fixed successfully

GPS stops working

2.3.2 Blue LED(GPS signal indicator)

Definition

Searching GPS signal

Status

Quick flashing

Slow flashing

Dark

GSM/GPRS online

No GSM signal or no SIM card installed

2.3.3 Green LED(GSM signal indicator)

Definition

GSM initializing

2.4 Arm status

When red/green/blue 3 LED lights are flashing in cycle, it means the terminal is in arm mode.

NOTE:

(1) The terminal should be placed under cover;

(2) protect it from water;

(3) Use bandage or foam tape to keep the terminal

stable;

(4) Please make sure that the front side of the terminal

should be facing up without any metal cover.

Under front windshield

Under rear windshield

Around dashboard

Page 4: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

05 06

3.2 Wiring

NOTE:

The GPS signal will be weaken if the device is installed

under the driver seat.

Page 5: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

07 08

1

5 7

2 3 4

6

/SOS button

(1) Black wire(negative): Use multimeter to find out the

battery negative.

(2) Orange wire(ACC): Use multimeter red pen to

connect with the ACC wire at ignition switch, while

the black pen connects with the ground wire. In this

condition, when the ignition switch is off, the voltage

is 0V; when the ignition lock is ON, the current

voltage will be shown.

(3) Red wire (positive): connect to the positive pole of

the battery.

(4) When the terminal is connected to external power,

insert the SIM and the red indicator (power indicator)

should be normally on. When the ignition switch is off,

the red indicator should be flashing slowly.

(5) The yellow wire of the relay control line should be

connected to 86 as the picture shows.

4.Power ON/OFFNOTE:

SIM should active GPRS, Caller ID and SMS service.

1.When you insert the SIM card,

the device will be on

automatically. (Mind the

direction of the SIM).

4.1 Power ON

Page 6: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

SIM cover

2.Restore the SIM cover.

09 10

3.Lock the SIM cover with two screws, connect with

external power.

Remark:

1. LED flashing when device is on.

2. Green LED quick flashing – searching GSM signal.

3. Blue LED quick flashing – searching GPS signal.

4. Green LED slow flashing – login server success.

5. Blue LED slow flashing - GPS is located.

1.Disconnect external power, take out the screws on

SIM cover.

4.2 Power OFF

screws

screws

screws

screws

2.Unlock the SIM cover.

SIM cover

Page 7: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

3.Pull out the SIM card,

the terminal will be off automatically.

Press the SIM down it

will be pushed out

5.Main Functions5.1 SOS(Optional)

In emergent case, press SOS for 3s to activate SOS alarm. Then the device will send SOS SMS to preset SOS numbers and then dial the numbers in 3 circles until the call is picked up. Alarm message will also send to platform.

11 12

5.2 Power cut-off alarm

When the electricity supply of device is cut off, it will activate cut-off alarm.

5.3 Low battery alarm

When battery is low, the device will activate low battery alarm.

5.4 Movement alarm (Default OFF)

Device will send movement alarm when vehicle moves out the pre-set distance (when ACC is off and GPS is fixed).

5.5 Vibration alarm (Default ON)

When vehicle vibrates several times, the vibration alarm will be triggered. If no ignition after 3 minutes (ACC OFF), the device will send vibration alarm message immediately.

5.7 Oil/Electricity cut-off

When vehicle is stolen, oil/electricity cut-off command can be sent by platform, APP or SMS.

Notice:

1. Make sure ACC is correctly connected.

2. When ACC is OFF, command will be executed

immediately.

3. When ACC is ON, but GPS is not fixed, command will

be postponed.

4. When ACC is ON, GPS is fixed, command will be

executed when vehicle speed is less than 20km/h.

5.8 Restore oil/electricity

When alarm is cancelled, user can send restore oil/electricity command by platform, APP or SMS and restore vehicle power.

Page 8: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

5.9 Restart device

13 14

If GPRS is abnormal (device is offline), user can send SMS command(RESET#)to restart the device. Device will reboot after 20 seconds after receive the command.

6.Platform Operation

Get registered on the designated service platform by authorized dealer, then you can start the tracking service and settings.

6.1 Login service platform

Please login the designated service platform to set and operate the device.

6.2 Download APP

Please download and install the APP in designated website, APP store or Google Play store.

iOS Android

7.Frequently Used Command List

STATUS#Check device status

WHERE#Get device GPS latitude/longitude

1, URL#2, POSITION

Check device location in Google Map link

1, Add SOS number: SOS,A,number 1,number 2,number 3# Example: SOS,A,12342***, 134533***,135432***#2, Delete subjected sequence of SOS number: SOS,D,number sequence 1,number sequence 2, number sequence 3# Example: SOS,D,1,2#3, Delete the SOS number: SOS,D,phone number#4, Query SOS number: SOS#

SOS number setting

TIMER,T1,T2# T1=5~18000 seconds;ACC ON upload interval;default value:10 T2=5~18000 seconds;ACC OFF upload interval;default value:20 (when GPS is on) Example: TIMER,20,20#

GPS data upload time interval

DISTANCE,D# D=0、50~10000 meter;Distance interval;default value:300, unit:meter;

GPS data upload distance interval

Page 9: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

DEFENSE,A# A:1~60 minutes,set delayed defense,default value:10 minutes

Delayed defense setting

1, SENALM,ON#2, SENALM,OFF#

Vibration alarm(Default ON)

1, MOVING,ON,R,# R=100~1000; Movement radius, unit: meterExample: MOVING,ON,200,#2, MOVING,OFF#

Movement alarm (Default OFF)

RELAY,A# A=0/1; 0: Restore petrol,1: cut off petrol;default value:0Example: RELAY,1# means: Cut off petrol

Petrol/electricity control

RESET#Device restart 20 seconds after receiving this command

Restart

15 16

8.Trouble shooting

If you are having trouble with your device, try these troubleshooting procedures before contact ing a service professional.

SolutionsProblems Causes

Poor signal

The signal waves unable to transmit when use the GPS tracker in the places that have poor signal reception, such as: tall building around or basement.

Using the GPS tracker in the places that have good signal condition.

Charge the device battery

Unable to boot

Low battery

Using the GPS tracker in the places that have good signal condition.

Unable to connect to the network

Poor signal

Change the installation place

Unable to locate

Signal shielded or Poor signal

Turn it onNo power off alarm

Built-in battery is off

Restore power/Check ACC

Fail to start the car

Power cutoff /ACC abnormal

Connect the device negative electrode to constant power

Car stops driving

Abnormal power supply

Check power supply/Press side key to activate indicators

Offline/Indicators off

Abnormal power supply/Indicators sleep

Change installation place and run the device again in open air.

No update of vehicle's location

No GPS positioning

Page 10: User Manual - Tienda Senix...2016/01/08  · 7.Frequently Used Command List Check device status STA U # WHERE# Get device GPS latitude/longitude 1, URL# 2, POSITION Check device location

17

Maintenance Record

Date Serviced by

Product Model

IMEI Number

Fault Descriptions

Comments