1 1

User manual

lo/med/hi speed

4CH

3DAutomatic Trimming

Camera attached

Please recycle this packaging responsibly.

All trademarks are acknowledged as the property of their respective owners. Unless otherwise stated their use does not imply that the trademark owner

is affiliated with Kondor or endorses the products herein.

Contents may vary to image shown.

JB. 4010 / DROCAM4 / Made in China © Kondor Ltd 2015. Christchurch, Dorset, BH23 4FL, UK

2

Contents

Box contents 4

Preparing to use the drone 4

Flying safety precautions 4

Battery installation and charging 4

Battery protection 5

Controller 5

Installing the camera 10

Saving photos and videos 10

Flips and rolls 11

Maintenance 12

Replacing damaged blades 12

Remote controlled aircraft 13

Safety information 14

Care for your Orbit CAMXL Drone 14

Specifications 15

Troubleshooting 15

Arcade Drone

The Arcade drone offers you the chance to ignore the boundaries and play in a totally new way. With an operational range of 80 metres, there is nothing stopping

you from taking your drone wherever you go. Unleash your creativity with the radicalflipsandrollsthatyoucanperformwithyourdone.

Please note: Line drawings used are generic, but this manual has been written specifically for your drone.

4 5

Drone Remove the battery from the drone. Once the battery is fully disconnected, insert the connector of the battery into the USB charge cable and insert into a PC/Mac, laptop or USB mains adaptor. The red LED on the USB will appear whilst charging and will turn off once it is fully charged and ready to use.

Please read this manual carefully before use.Box contents– Drone + Camera– Controller – User manual – Battery– Spare blades – USB charging cable– Camera transfer cable – 4 GB SD card

Preparing to use the drone1. Fully charge the battery and insert it into the drone. Then insert the required batteries into the controller.

See Battery installation and charging.2. Make sure the take off/flight area is clear of people or other obstacles. 3. Press the power button on the controller (one beep), push the left stick up and back down (double beep)

and once the LED lights stop flashing, it is then ready to use.4. Push the left stick (throttle) slowly forward, the drone will take off.

Flying safety precautions– To avoid choking, keep small parts out of reach from children– Make sure to carefully push upwards with the throttle when taking off, to avoid anyone getting hit with the drone– Disconnect the battery from the drone after use and then turn off the controller– Do not put the battery in high temperatures or near a heat source– To avoid injury or damage, make sure the drone is flown at least 2 metres away from people or obstacles– When used by a child, make sure an adult is supervising. Make sure the drone is kept in clear view at all times– Always turn the power of the controller off and drone when not in use

Battery installation and chargingControllerA – Battery cover B – Battery details (4 x AA)

Battery protectionThe Arcade drone is equipped with low-voltage protection, meaning that when the battery reaches a low capacity, the programmed control system will stop the electrical supply to the rotors. Once this happens, recharge the battery fully before using the drone. When the blades are jammed, to prevent damage, the control system will stop electricity to the rotors.

Controller a) Speed selectb) Left stick/Throttlec) Trim slider B d) Trim slider A e) Power switch f) Trim slider D g) Capture photo h) Capture video i) Trim slider C j) Right stick/Rudder k) LED on/off

ka

b

c

d

e

i

hgf

j

A

B

To install batteries into the controller: Carefully remove the screw from the above section of the battery cover, remove the cover and insert 4 x 1.5 V AA batteries, according to indicated polarity.Note: Batteries are not included.Make sure the batteries (AA) are correctly installed under the supervision of an adult. Refrain from mixing old and new batteries as well as different types.

6 7

Controller overview The Arcade drone controller can be used in 2 modes:Mode 1 (default) The left stick controls pivotal turning, the right stick controls lateral flight. Mode 2 The left stick controls lateralflight, the right stick controls pivotal turning. To toggle between the two controller modes, press and hold the Control Mode Switch until you hear a beep sound.

The Arcade drone has three different programmed speeds. Toggle through these three speed settings using the Speed Select button. Press to hear 1 beep for speed 1 (slow), 2 beeps for speed 2 (medium) and 3 beeps for speed 3 (fast). Speed 3 is required for the flips and rolls manoeuvres (see Flips and rolls). The Arcade drone has an auto-trim function (fine-tunes all rotors balance). Use this function if your Arcade drone is not hovering in a balanced position. To auto-trim all the rotors, turn on the drone, place it on a flat surface, and power the controller (push the power button upwards) whilst holding down the Auto-trim button.

Throttle/Left stick: While in mode 1, up/down, left/right pivot turn. While in mode 2, up/down, left/right side fly.

Rudder/Right stick: While in mode 1, up/down, left/right side fly. While in mode 2, up/down, left/right pivot turn.

Trim slider A: Adjust throttle positionTrim slider B: While in mode 1, used for left/right pivot turning, manual fine-tuning.

While in mode 2, used for left/right side flight, manual fine-tuning.Trim slider C: While in mode 1, used for left/right side flight, manual fine-tuning.

While in mode 2, used for left/right pivot turning, manual fine-tuning.Trim slider D: Used for forward/reverse flight, manual fine-tuning in modes 1 and 2.

LED controls / Control mode switch:– Press once for LED lights on/off toggle function. – Press and hold until beep sounds to toggle between Controller modes.Note: taking photos and recording video features are explained in Installing the camera.

Forward and backward

Forward and backward

Left spin and right spin

Left spin and right spin

Left side and right side

Left side and right side

Up and down

Up and down

ControllerflightsticksMode 1:

Note: When the drone is facing backwards, the controls are reversed.

Left spin

Leftside fly

Leftside fly

Left spin

Right spin

Rightside fly

Rightside fly

Right spin

Mode 2:

Note: Please ensure you have fully read and understand the operating flight sticks for both mode 1 and 2. It is advised to learn both layouts to avoid damage whilst flying, and for user satisfaction.

Rise

Drop

Rise

Drop

Forward

Forward

Backward

Backward

8 9

Trimming:

Downward trim

Upward trim

Backward trim

Forward trim

Left side trim

Right side trim

Left spin trim

Right spin trim

Upward

Downward

Forward

Backward

Downward trimmer

Upward trimmer

Backward trimmer

Forward trimmer

Leftside trimmer

Rightside trimmer

Left spin trimmer

Right spin trimmer

Trimming:

Downward trim

Upward trim

Backward trim

Forward trim

Left side trim

Right side trim

Left spin trim

Right spin trim

Upward

Downward

Forward

Backward

Downward trimmer

Upward trimmer

Backward trimmer

Forward trimmer

Leftside trimmer

Rightside trimmer

Left spin trimmer

Right spin trimmer

Controller functions – trim tuning Mode 1:

a) Upward/Downward fine tuning b) Left/Right spin fine tuning c) Forward/Backward fine tuning d) Left side/Right side fine tuning

a

b

c

d

Mode 2:

a) Upward/Downward fine tuning b) Left side/Right side fine tuningc) Forward/Backward fine tuning d) Left/Right spin fine tuning

a

b

c

d

Note: it is best to manual trim the Arcade drone while it is hovering. Note: it is best to manual trim the Arcade drone while it is hovering.

10 11

Flips and rollsNow you have the basics of flying, you are now ready to put your skills to the test. Select the third speed mode and start learning to flip and roll your drone, and master full aerial acrobatics. To do this select the highest speed mode; see Controller functions for details. The top left trigger controls the speed modes, and pressing this changes the level of speed of the drone: speed 1 (default), speed 2 (two beeps) and speed 3 (three beeps). To perform a flip or roll, press the top trigger twice, make sure the drone is at least 3 metres off the ground, and quickly push the right flight stick (Rudder) in either direction to make the drone flip or roll. Once the manoeuvre is completed, steady the drone. It is recommended to press the trigger once more to set it back to speed mode 1. Note: The flips and rolls directional functions can be different, depending on which Control mode was set on the controller (Mode 1 and 2). Refer back to Controller overview for these instructions.

Right flipMode 1: Left flip

Forward flip Backward flip

Right flipMode 2: Left flip

Forward flip Backward flip

A

B

Saving photos and video Step 1: Use the camera transfer USB cable supplied in the box, connecting the camera to PC/Laptop. Step 2: Once connecting this may either trigger an automatic shortcut message or you will need to open

it through “My Computer”. Step 3: Opening the device will produce two folders “Photos” and “Videos”, the photos will be in JPEG format

and the video in AVI format. Note: if the files do not play, you may need to convert them or download alternative software. Any additional software installed is at your own risk.

Installing the camera Step 1: Insert a micro SD card into the port on the side of the camera. Make sure it is up-right and push it fully

in to secure it. Step 2: Find the small (black, green and white) cable and insert it to white port on top of the camera. Step 3: Position the camera at the rear of the drone and push the two connectors into the holders.

Taking photos and video• To take photos press the button (A) once and the red light will indicate the photo has been taken• To capture video press the button (B) once and the red light will flash, indicating the camera has started filming • To stop filming, press the button once again and when the red light turns off this means it’s stopped

12 13

A

A

B

B

Maintenance 1. Wipe the drone with clean, dry soft cloth. 2. Avoid irreparable damage by not using the drone in the rain or near water.3. Check the drone and accessories for damage. If damage is found, do not use the drone until you have replaced

the damaged parts.

Replacing damaged bladesYour drone comes with four replacement blades. The four blades are divided into two different forms. These are set A and set B, each are visibly differentiated by the icons on the underneath of each blade. Before applying a replacement blade, check for the A or B icon beneath both the damaged and replacement blades to make sure they match. To replace a blade, carefully remove the screw and pull it upwards and it will come away from the motor. Next exchange the damaged blade with the new one, by placing it over the motor, push downwards and replacing the screw. Make sure it is fully in place by giving it a final push and manually spin it with your finger, to check it turns correctly.

Remotecontrolledaircraft:responsibleflyingThis drone is a toy, but that does not mean that you should not take care when you are flying it, both inside and outside. If your drone has a camera attached, or it is being flown for a commercial reason, the UK law states that your drone will be treated like any other aircraft. This means that there are certain laws that you need to follow when you are playing with your drone – for your own safety, and the safety of others:1. When you play with the drone, you are completely responsible for it.2. You should always be able to see your drone when you are flying it.3. As you are in control of the drone, it is up to you to ensure that it does not crash into other people, or other objects.4. Residential streets and town centres are examples of congested areas. Drones must stay away from congested

areas by at least 150 metres.5. Your drone must be at least 50 metres away from any vehicles, buildings or structures, or any person whether

alone or in a group – irrespective of the height of your drone.6. The Civil Aviation Authority (CAA) must be informed if you intend to use any camera footage from your drone to

earn money.7. You should not fly your drone near any airfield or airport, or near any power installations such as pylons.

Remember: UK Aviation Law is there to protect you and everyone else, and there are severe repercussions if you break these laws, including the potential of criminal prosecution.For more details on this, and information about how to fly your drone safely, visit: www.caa.co.uk/uasYour drone has a camera, which means that you also need to be aware of the Data Protection legislation that exists in the UK.In accordance with Data Protection legislation (Data Protection Act 1998) consent should be obtained from any individual who is the focus of a video recording in order to process his/her personal data fairly. Where a recording involves individuals other than the main players, then, in some circumstances, the images of other individuals may constitute personal data and the data protection regime may come into play, particularly where the video conveys information of biographical significance to the individual concerned. However, where filming takes place in a public place, the fact that a passer-by is captured in the film in the background and is able to be identified by individuals who know him/her does not in itself make the image personal data and consent is unlikely to be required to put the video on YouTube or incorporate it in an Open Educational Resource (OER).If you want to read more about the Data Protection Act, or you want to learn more about how this affects you, go to www.legislation.gov.uk/ukpga/1998/29/contentsPlease check the local regulations and legislations before you fly your drone.

14 15

Cable length 600 mm

Battery capacity 580 mAh

Charging time up to 1.5 hours

Play time up to 7 minutes

Frequency 2.4 GHz

Batteries 4 x AA

Drone size H80 x W330 x D330 (mm)

Drone weight 118 g

Specifications

We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product improvement and development.

Troubleshooting If you experience any unusual issues with your Arcade drone, bring it down safely, turn off the controller and carefully disconnect the battery.The use and operation of this Drone is beyond our control. Warranty of the Drone is limited to defects caused by faulty manufacture or defects in materials only. Please ensure you operate this product with total care and attention at all times. We cannot be held responsible for any damage whatsoever that may be caused to you or anyone else.This does not affect your statutory rights. We hope you’ve now got all the information you need to get started, but if you’re having problems with anything, please feel free to contact us at: support@kondor.co.uk

Please do not attempt to open this product. There are no user serviceable parts inside, in particular if your product has an embedded, non-replaceable battery, do not attempt to access or remove the battery as this may cause personal injury and will damage the product.

Making any attempt to open the product or carry out repair voids any and all warranties.

Safety information– The control distance will be reduced if the Arcade drone or controller is not fully charged– If the drone becomes damaged, stop using it immediately– Remove the batteries from the controller, when not using it for more than a few days– Do not touch the drone whilst flying, to avoid damage to yourself– Do not touch the motor during or straight after use, to avoid burning yourself– Ensure the surrounding area is free of people and obstacles before flying the drone– Not suitable for children under 14 years old. Children should be supervised at all times by an adult– Ensure replacement blades are attached correctly to avoid damage to the user or property– Do not dispose of the parts of the product in a normal recycling bin. All parts should be taken to your local

recycling centre

Care for your Orbit CAMXL DronePlease DON’T

– Get the Orbit CAMXL Drone wet– Drop the Orbit CAMXL as this will invalidate your warranty – Open up the Orbit CAMXL as there are no user serviceable parts inside– Use any other mains adaptor than the one supplied– Expose the Orbit CAMXL to extreme temperatures or rapid changes of hot to cold or vice versa

Please DO

– Clean the Orbit CAMXL with a soft dry cloth and no detergents