User Manual ICS-W0837B V1
description
Transcript of User Manual ICS-W0837B V1
ICS-W0837B
User Manual <Interference Cancellation System for WCDMA 5 Watt>
2010. 7
RF Window Co., Ltd. | 2
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[ Table of Contents ] 1. System Overview................................................................................................. 10
2. System Network Configuration ............................................................................ 11
2.1. Service for Network.............................................................................................. 11
2.2. NMS Network....................................................................................................... 12
3. System Specification............................................................................................ 13
3.1. System................................................................................................................. 13
3.1.1. WCDMA System Specification ........................................................................ 13
3.2. System Configuration........................................................................................... 15
3.3. Environment Specification.................................................................................... 16
3.4. Mechanical Specification...................................................................................... 16
4. Housing................................................................................................................ 17
4.1. Housing Configuration ......................................................................................... 17
4.1.1. System ............................................................................................................ 17
4.1.2. System Block Plan .......................................................................................... 18
4.1.3. System External Connector Plan .................................................................... 19
5. Main Module Configuration.................................................................................. 20
5.1. ICM (Interference Cancellation Module) .............................................................. 20
5.1.1. ICM ................................................................................................................. 20
5.2. Filter ..................................................................................................................... 21
5.2.1. Donor & Service Duplexer............................................................................... 21
5.3. Dual HPA ............................................................................................................. 22
5.3.1. Dual HPA......................................................................................................... 22
RF Window Co., Ltd. | 3
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5.4. Power Supply....................................................................................................... 23
5.4.1. Power Supply .................................................................................................. 23
5.5. INTERFACE......................................................................................................... 24
5.5.1. INTERFACE.................................................................................................... 24
5.5.2. VFD ................................................................................................................. 26
5.5.3. KEY-PAD......................................................................................................... 29
6. Main features of system operation and monitoring program............................. 30
6.1. Download Feature................................................................................................ 30
6.1.1. Objective ......................................................................................................... 30
6.1.2. Procedure........................................................................................................ 30
6.2. ICS Gain Setup Feature....................................................................................... 30
6.2.1. Objective ......................................................................................................... 30
6.2.2. Procedure........................................................................................................ 30
6.2.3. Others ............................................................................................................. 31
6.3. Total Power Limit.................................................................................................. 31
6.3.1. Objective ......................................................................................................... 31
6.3.2. Procedure........................................................................................................ 31
6.4. Auto Recovery ..................................................................................................... 32
6.4.1. Objective ......................................................................................................... 32
6.4.2. Procedure........................................................................................................ 32
6.5. Up Link Auto Shutdown Mode.............................................................................. 32
6.5.1. Objective ......................................................................................................... 32
6.5.2. Procedure........................................................................................................ 32
6.6. NMS Operation .................................................................................................... 33
RF Window Co., Ltd. | 4
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
6.6.1. Alarm Monitoring feature................................................................................. 33
6.6.2. LED Feature.................................................................................................... 33
7. GUI ...................................................................................................................... 34
7.1. Program Overview ............................................................................................... 34
7.2. PC Requirement .................................................................................................. 34
7.3. How to Use .......................................................................................................... 34
7.3.1. Program Installation ........................................................................................ 34
7.3.2. Program Start .................................................................................................. 34
7.3.3. Window description ......................................................................................... 35
7.3.4. Communication Setup..................................................................................... 36
7.3.5. Repeater Status .............................................................................................. 37
7.3.6. Repeater Monitoring........................................................................................ 37
7.3.7. Repeater Control............................................................................................. 42
7.3.8. Control Item..................................................................................................... 45
7.3.9. Firmware Download ........................................................................................ 46
7.3.10. Data Debugging....................................................................................... 48
7.3.11. Feedback Signal Status Check................................................................ 48
8. System Installation and Setup ............................................................................. 51
8.1. Installation............................................................................................................ 51
8.1.1. Configuration................................................................................................... 51
8.1.2. Installation ....................................................................................................... 51
8.1.3. Check List before operation ............................................................................ 52
8.1.4. RF Monitor Port............................................................................................... 52
8.2. Process of ICS Repeater setup and installation .................................................. 53
RF Window Co., Ltd. | 5
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
8.3. Fault / Alarm Handling.......................................................................................... 54
8.3.1. Down Link / Up Link ALARM Handling............................................................ 54
8.3.2. Environment Alarm.......................................................................................... 55
9. Manufacturer Information..................................................................................... 56
RF Window Co., Ltd. | 6
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[List of Figures] [FIGURE - 1] SYSTEM NETWORK CONFIGURATION 1................................................... 11
[FIGURE - 2] SYSTEM NETWORK CONFIGURATION 2................................................... 11
[FIGURE - 3] NMS NETWORK CONFIGURATION.............................................................12
[FIGURE - 4] FRONT AND SIDE VIEW...............................................................................17
[FIGURE - 5] REAR VIEW...................................................................................................17
[FIGURE - 6] SYSTEM BLOCK PLAN.................................................................................18
[FIGURE - 7] SYSTEM EXTERNAL CONNECTORS..........................................................19
[FIGURE - 8] DOWN LINK/UP LINK ICM ............................................................................20
[FIGURE - 9] DONOR & SERVICE DUPLEXER .................................................................21
[FIGURE - 10] DOWN LINK PAU ........................................................................................22
[FIGURE - 12] POWER SUPPLY ........................................................................................23
[FIGURE - 13] INTERFACE.................................................................................................24
[FIGURE - 14] RCU VFD MENU TREE...............................................................................26
[FIGURE - 15] KEY-PAD......................................................................................................29
[FIGURE - 16] GUI MAIN WINDOW....................................................................................35
[FIGURE - 18] GUI COMMUNICATION SETUP..................................................................36
[FIGURE - 19] GUI COMMUNICATION STATUS WINDOW ...............................................36
[FIGURE - 20] GUI SYSTEM STATUS ................................................................................38
[FIGURE - 21] GUI PSU STATUS........................................................................................39
[FIGURE - 23] GUI DOWN LINK SETUP STATUS..............................................................40
[FIGURE - 24] GUI UP LINK SETTING STATUS ................................................................42
[FIGURE - 25] GUI WCDMA (3G) CONTROL WINDOW ....................................................43
[FIGURE - 26] FIRMWARE DOWNLOAD WINDOW...........................................................47
RF Window Co., Ltd. | 7
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[FIGURE - 27] GUI DEBUG WINDOW................................................................................48
[FIGURE - 28] SIGNAL STATUS WINDOW ........................................................................48
[FIGURE - 29] PROCESS OF ICS REPEATER SETUP AND INSTALLATION...................53
RF Window Co., Ltd. | 8
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[ List of Tables ] [TABLE - 1] RF SYSTEM SPECIFICATION.........................................................................14
[TABLE - 2] SYSTEM CONFIGURATION............................................................................16
[TABLE - 3] ENVIRONMENT SPECIFICATION...................................................................16
[TABLE - 4] MECHANICAL SPECIFICATION......................................................................16
[TABLE - 5] MODULES........................................................................................................18
[TABLE - 6] SYSTEM EXTERNAL CONNECTORS ............................................................19
[TABLE - 7] MECHANICAL SPECIFICATION......................................................................19
[TABLE - 8] INTERFACE FEATURES .................................................................................25
[TABLE - 9] RCU STATUS CONTROL DETAILS.................................................................29
[TABLE - 10] KEY FEATURE...............................................................................................29
[TABLE - 11] GUI PC REQUIREMENT................................................................................34
[TABLE - 12] REPEATER STATUS DETAILS......................................................................37
[TABLE - 13] SYSTEM MONITORING ................................................................................38
[TABLE - 14] PSU MONITORING........................................................................................39
[TABLE - 16] DOWN LINK MONITORING...........................................................................40
[TABLE - 17] UP LINK MONITORING .................................................................................41
[TABLE - 18] SYSTEM CONTROL ITEM.............................................................................45
[TABLE - 20] DOWN LINK CONTROL ITEM .......................................................................46
[TABLE - 21] UP LINK CONTROL ITEM .............................................................................46
[TABLE - 20] SYSTEM CONFIGURATION..........................................................................51
[TABLE - 21] DC IN CONNECTOR PIN ASSIGN ................................................................51
[TABLE - 22] AC IN CONNECTOR PIN ASSIGN.................................................................51
[TABLE - 25] SYSTEM CONNECTION PORT.....................................................................52
RF Window Co., Ltd. | 9
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[TABLE - 26] RF MONITOR PORT......................................................................................52
[TABLE - 27] DOWN LINK / UP LINK ALARM HANDLING .................................................55
[TABLE - 28] ENVIRONMENT ALARM................................................................................55
RF Window Co., Ltd. | 10
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
1. System Overview
ICS-W0837B is a digital repeater that provides optimized service with ICS (Interference
Cancellation System) to make the most efficient way to enhance WCDMA network. ICS-W0837B consists of the same construction as normal RF repeater except DSP
(Digital Signal Processing) part and it can overcome oscillation problem caused by lack of the isolation level between donor and coverage antennas.
ICS-W0837B can automatically compensate rapidly-changing input signals including echo feedback signals caused by multi-path environment and it has various advantages for operation and maintenance. ICS-W0837B consists of ICM (Interference Cancellation Module) that cancels feedback signals, RF signal amplifier, MCU (Main Control Unit), and modem (optional) to operate with NMS(Network Management System).
RF Window Co., Ltd. | 11
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
2. Network Configuration 2.1. Service for Network
ICS-W0837B can provide Cell Coverage to a Node-B with using PAU and it is for
expansion of WCDMA Cell Coverage. The System Network Configuration of ICS-W0837B is shown as below
α
β
γα
T1/E1
Wireless
Repeater Cell
Repeaterα
β
γ α
β
γα
T1/E1
Wireless
Repeater Cell
Repeater
[Figure - 1] System Network Configuration 1
α
β
γ α
T1/E1
Optic Fiber
Repeater Cell
Repeater
WirelessRepeater
α
β
γ α
β
γ α
T1/E1
Optic Fiber
Repeater Cell
Repeater
WirelessRepeater
[Figure - 2] System Network Configuration 2
RF Window Co., Ltd. | 12
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
Input level of ICS-W0837B is air interfaced with RF signal of WCDMA transferred from
Node-B and mobile through Donor and Service Antenna. The system consists of ICM that cancels feedback signals, RF signal amplifier, monitoring and control processor, and modem to operate with NMS (Optional).
The system has features that the Node-B RF signal through the donor antenna, ICM and
amplified by PAU of down link to pass the signals to service antenna. Also, it takes the mobile input signal through service antenna, ICM and amplifier to pass the signals to donor antenna. ICM consists of two parts, RF part and Digital part and ICM cancels feedback signals for DL and UL. DL HPA consists of AMP block that amplifies RF signals and Controller block that monitor and controls Amp block.
2.2. NMS Network ICS-W0837B can be connected with WRCS which has been already operating. The Connection of between WRCS and ICS-W0837B meets the standard of service
provider.
[Figure - 3] NMS Network Configuration
RF Window Co., Ltd. | 13
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
3. System Specification 3.1. System 3.1.1. WCDMA System Specification
Parameter Down Link Up Link Remark
1 Carrier B1H, B1L Number of Carrier
2 Carrier B2
885MHz ~ 890MHz
(Center: 887.5MHz)
840MHz ~ 845MHz
(Center: 842.5MHz) B1H
880MHz ~ 885MHz
(Center: 882.5MHz)
835MHz ~ 840MHz
(Center: 837.5MHz) B1L Frequency Range
880MHz ~ 890MHz
(Center: 885MHz)
835MHz ~ 845MHz
(Center: 840MHz) B2
3.84MHz (3.84MHz/Carrier) B1H, B1L Band Width
8.84MHz (3.84MHz/Carrier) B2
Flatness 3dB p-p
Input Power Range -63dBm ~
-33dBm/Total -50dBm/Total(Under) @ Max Power
Output Power +37dBm/Total +27dBm/Total
System Gain 70dB~100dB 70dB~100dB
Gain Control Range 30dB @1dB/Step
System Delay < 8㎲
Waveform Quality EVM ≤ 12.5% With 10 multi-path
feedback signal
PCDE < -35dB
Frequency Stability < 0.01ppm
VSWR < 1.5 : 1
RF Window Co., Ltd. | 14
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
Parameter Down Link Up Link Remark
TX/RX Isolation > 110dBc
Noise Figure - < 7dB @Max. Gain
Out-Band ACLR ≥ 45dBc @Fc±5MHz
≥ 50dBc @Fc±10MHz
2nd Harmonics > 80dBc
Impedance 50ohm
[Table - 1] RF System Specification
RF Window Co., Ltd. | 15
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
3.2. System Configuration
Parameter Specification Remark
Donor Antenna Duplexer Filter Type
Service Antenna Duplexer
Power Supply AC Input Voltage : 90VAC ~ 264VAC(50Hz/60Hz)
DC Input Voltage : +24VDC(+21VDC ~ 29.5VDC)
RF Connector Type Antenna : 7/8 Inch Din Type Female
Power Connector Type
AC
- MS3102A22S-2P(3Hole male)_MIL-C-5015
TYPE
DC
- MS310A20-8P(6Hole male)_MIL-C-5015 TYPE
Size 305mm(W) X 565mm(H) X 162mm(D) With bracket
weight 30Kg (Under)
Power Consumption 190W (Under)
Chasing level IP56
Operation Temperature -20°C ~ +55°C(95%RH) NEBS GR-63-
CORE Section4.1.2
Storage Temperature -40°C ~ +80°C(95%RH) NEBS GR-63-
CORE Section4.1.2
OMC Include Monitoring-Control-Alarm NEBS GR-63-
CORESection4.1.1
Box panel for security of
repeater Proportional
Local/Remote Control USB Port at local, Modem(Option)
Optional (Mute be) Remote Access
RF Window Co., Ltd. | 16
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
Software Setting Under Windows
Modem for remote Include / one package
[Table - 2] System Configuration
3.3. Environment Specification
Item Specification Remark
AC Power AC 90 ~ 264V
Consumption power Under 190W
Operating Temperature -20°C ~ +55°C
Operating Humidity 5% ~ 95%
Storage temperature -40 ~ +80°C(5~95% RH)
Ingress protection IP65
[Table - 3] Environment Specification
3.4. Mechanical Specification
Item Details
Size 305(W) X 565(H) X 162(D)
Weight Under 30Kg
Convection type Natural convection
Mounting Wall & poll (modified based on user request)
Cabinet type Outdoor (compliant with IP 65)
[Table - 4] Mechanical Specification
RF Window Co., Ltd. | 17
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
4. Housing 4.1. Housing Configuration 4.1.1. System
[Figure - 4] Front and Side View
[Figure - 5] Rear View
RF Window Co., Ltd. | 18
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
4.1.2. System Block Plan
[Figure - 6] System Block Plan
No. Module Name
1 ICM
2 INTERFACE (with Modem)
3 DUPLEXER (TOP)
4 DUAL HPA (BOTTOM)
5 PSU
[Table - 5] Modules
①
②
③
④
⑤
RF Window Co., Ltd. | 19
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
4.1.3. System External Connector Plan
[Figure - 7] System External Connectors
No. Name
1 AC 100~260V Input Port
2 Bluetooth Modem port
3 Donor Antenna Port
4 Service Antenna Port
[Table - 6] System External Connectors
Item Specification
Size 305mm(W) X 565mm(H) X 162mm(D)
Material Aluminum(AL5052, AL6063) for rust protection
Cooling Natural Convection with Heat Sink
Locks 2 EA on the side of cabinet
Antenna
Port
1. Location : 2 Ports at the under of housing
2. Connector Type : DIN Type
Modem
Port
1. Location : 1 Port at the lower of housing
2. Connector Type : SMA Type
Ground M5 2Hole
Environmental
Condition
1. Water proof : outdoor type
2. ∆T : within 20℃
3.Vibration : 1G, 10~150Hz, 0.1oct/min, XYZ
[Table - 7] Mechanical Specification
①
② ③ ④
RF Window Co., Ltd. | 20
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5. Main Module Configuration 5.1. ICM (Interference Cancellation Module)
ICM is located between Antenna connector and Dual HPA. It is designed to resolve the problems caused by near-far among operators and LNA built-in to amplify a low noise and make satisfied stop band rejection. It operates to transmit signals to Dual HPA and to maintain signal regularly input to final amplifier after determining gain to need for system after conversing signal processed from DSP to frequency. It is also operated the function of Remote Control Unit through INTERFACE.
5.1.1. ICM
[Figure - 8] Down Link/Up Link ICM
RF Window Co., Ltd. | 21
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5.2. Filter It is 10MHz Band Pass Filter and consists of Service and Donor. Service Duplexer has
40dB Coupler to monitor Output power and Donor Duplexer has 30dB Coupler to monitor Input power. Hence it can enable to measure the signal level and to observe its specification.
5.2.1. Donor & Service Duplexer
[Figure - 9] Donor & Service Duplexer
RF Window Co., Ltd. | 22
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5.3. Dual HPA Down link PAU receives the signal from ICM and amplifies it finally. This is designed to
keep up the stable output power of system in order to satisfy electrical specification of system output power. It is a Linear Amp with output power 8W in down link, 1W in up link (@WCDMA 2FA) and
executes Drive Amp feature simultaneously while Gain is 47dB in Down Link, 33dB in Up Link. Input Voltage is 27VDC and has alarm feature for over power, over temperature, and
VSWR. It has the same mount hole which can be applied for the same specification and configuration according to output power amount (8W/1W) and HPA manufacturer.
5.3.1. Dual HPA
[Figure - 10] Down Link PAU
RF Window Co., Ltd. | 23
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5.4. Power Supply PSU is designed to input AC 90~264V and to output DC +27V and +12V. +27V and Battery is designed for the Pin short protection by inferior and can provide a
stable power supply. It also has Back-Up Battery terminals so that the service can be provided even if there is power shortage.
5.4.1. Power Supply
[Figure - 11] Power Supply
RF Window Co., Ltd. | 24
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5.5. INTERFACE User can monitor and control the repeater by VFD and Keypad. Interface board consists
of 40Pin connector for communication with ICM, 16pin connector for communication with Dual HPA, 24pin connector for communication with Interface board receives electrical power from PSU and distributed the power to all of active module except Dual HPA. It also can communicate with all of active module. Debug port is designed based on USB connection
5.5.1. INTERFACE
[Figure - 12] INTERFACE
Term Feature
VFD Monitor and check the status
KEY-PAD Check and control the status
LED Check the status of Module
Modem Ant. Modem Antenna connection Port
Bluetooth Ant. Bluetooth Modem Antenna connection Port
USB GUI Port, System check with USB, PC
Power Supply ICM, INTERFACE, reverse Dual HPA power
PSU Status Status information of Power Supply Unit
VFD
KEY-PAD
LED MODEM ANTENNA
PORT
BLUETOOTH ANTENNA
PORT
USB
ICM
INTERFACE
POWER
INTERFACE
HPA
INTERFACE
RF Window Co., Ltd. | 25
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
Module Interface ICM, Dual HPA, Modem
Power supply/ Data Interface
[Table - 8] INTERFACE Features
RF Window Co., Ltd. | 26
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5.5.2. VFD 5.5.2.1. RCU VFD Menu Tree
[Figure - 13] RCU VFD Menu Tree
RF Window Co., Ltd. | 27
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
5.5.2.2. RCU status control menu
RCU status control menu
Item Details Remark
“ Fwd Status “
” ICS : [Normal] “
“ Fwd Status “
“ OUTPWR : 000dBm”
“ Fwd Status “
“ INPWR : -000dBm”
“ Fwd Status “
“ ISO. : 000dB”
“ Fwd Status “
“ GAINMODE : [GAIN]dB>”
Down Link GAIN setup Mode
[OFF]/[GAIN]
“ Fwd Status “
“ GAIN : 000dB>” Down Link GAIN Setup Mode
“ Fwd Status “
“ATTN : 000dB>” Down Link Attenuator Setup Mode
“ Fwd Status “
“ HIGH : [Normal]”
“FWD Status”
“ Fwd Status “
“ LOW : [Normal]”
“ Rvs Status “
” ICS : [Normal] “
“ Rvs Status “
“ OUTPWR : 000dBm”
“ Rvs Status “
“ INPWR : -000dBm”
“ Rvs Status “
“ ISO. : 000dB”
“ Rvs Status “
“ GAINMODE : [GAIN]dB>”
Up Link GAIN Setup Mode
[OFF]/[GAIN]/[BAL]
“RVS Status”
“ Rvs Status “
“ GAIN : 000dB>” Up Link GAIN Setup Mode
RF Window Co., Ltd. | 28
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
“ Rvs Status “
“ ATTN : 000dB>” Up Link Attenuator Setup Mode
“ Rvs Status “
“ BAL : 000dB>” Up Link Balance Setup Mode
“ Rvs Status “
“ HIGH : [Normal]”
“ Fwd AMP Status “
“ OVERPWR : [NORMAL] ”
“ Fwd AMP Status “
“ HI. TEMP : [NORMAL]”
“ Fwd AMP Status “
“ VSWR : [NORMAL]”
“ Fwd AMP Status “
“ DC : [NORMAL]”
“ Fwd AMP Status “
“ Device : [NORMAL]”
“FWD AMP Status”
“ Fwd AMP Status “
“ Amp : [ ON ]>”
Down Link Amplifier On/Off Setup
Mode
“RVS AMP Status” “ Rvs AMP Status “
“Amp : [ON]>” Up Link Amplifier On/Off Setup Mode
“ Environment ”
“ DOOR : [OPEN]”
“ Environment ”
“ TEMP : 000 ℃”
“ Environment ”
“ AC : [NORMAL]”
“ Environment ”
“ DC : [NORMAL]”
“ Environment ”
“ BATT : [NOTUSE]>”
Battery Use Setup Mode
(Uninstall, 29V embedded)
“ Environment ”
“ FAMODE : [MANUAL]>”
FA Mode Setup Mode
Manual (FA1~FA4), Auto
“Environment”
“ Environment ”
“ FAN : [MANUAL]>”
RF Window Co., Ltd. | 29
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
“ Environment ”
“ SLANT : [RESET]>” Slop Sensor Setup Reset
“ Environment ”
“ SLANT : [NORMAL]>”
[Table - 9] RCU Status Control Details
5.5.3. KEY-PAD
Menu Up Down Enter ESC
[Figure - 14] KEY-PAD
KEY-PAD uses 5 keys as above. Each meaning and operation is as below. The setup
Mode is only in P#02 and it can change a mode by setup. In P#02, a menu which can be setup is displayed as ‘>’
Key Step Status Mode Setup Mode
P#00 Move to P#01 N/A
P#01 Move to P#00 N/A Menu
P#02 Move to P#00 Move to P#00
P#00 N/A N/A
P#01 Upper menu of P#01 N/A Up
P#02 Upper menu of P#02 On or Increase
P#00 N/A N/A
P#01 Lower menu of P#01 N/A Down
P#02 Lower menu of P#02 Off or Decrease
P#00 Password window if press for 2 sec N/A
P#01 Move to P#02 N/A Enter
P#02 switch over to MoPe on setting menu Setting Value
P#00 N/A N/A
P#01 Move to P#00 N/A Esc
P#02 Move to P#01 Cancel setiting
[Table - 10] Key Feature
RF Window Co., Ltd. | 30
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
6. Main features of system operation and monitoring program 6.1. Download Feature 6.1.1. Objective To changed and updated features of system operation and monitoring program.
6.1.2. Procedure CPU (in ICM) performs download remotely through TCP/IP function of modem installed in
a repeater.
6.2. ICS Gain Setup Feature 6.2.1. Objective To keep up the fixed value of Gain desired by users for Down Link Path and Up Link Path
6.2.2. Procedure 1. Gain setup mode
1) User can set up Gain within a certain range.
① Down Link : 70B ~ 100B ② Up Link : 70dB ~ 100dB
2) Gain should be set up according to ICS repeater input condition. (ex) When input is -40dBm, Gain can be over Max. 67 dB because ICS repeater output cannot be over 37dBm)
3) When the Gain is less compared to Isolation, ICM set Attenuator. to optimized value in order to protect the system, and CPU occurs alarm and displays “Isolation deficient”
When Isolation is back to normal, Gain return to the previous set-up and “Isolation deficient” alarm is removed
2. OFF Mode 1) This can be established at the initial set-up or special occasion. When OFF mode,
Attenuator is set up to Maximum in order to protect the system
3. Gain Balance Mode 1) Up Link Gain is set up automatically as low as “Gain Balance set-up value
compared to Down Link current Gain
RF Window Co., Ltd. | 31
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
2) Gain Balance set-up range is 0 ~ 10dB and this mode can be set up at the Up
Link
6.2.3. Others At the initial execution, if Gain set-up is not executed normally, it is notified to the user and
holds the default Attenuator value
6.3. Total Power Limit 6.3.1. Objective To give out Total Power to be less than the output power value which user wants and to
operate output power limit feature when output power is more than max. Output power set-up
6.3.2. Procedure 1. Total Power Limit does not have additional operation Mode and it works based on
“max. output power value’ set up by user 1) Down Link Output Power set-up Range : ~ 38dBm/Total 2) Up Link Output Power set-up Range : ~ 28dBm/Total
2. Total Power Limit operating point: monitored value ≥ “max. output power set-up value 3. Total Power Limit Attenuator operating: After Down Link Attenuator change, turn down
Attenuator. To be 1 dB less than “max. output power set-up value” 1) The changed Attenuator. value should be stored in the system 2) When the changed Attenuator. value is reset
① RCU Reset ② Change User Attenuator. Value before changed Attenuator. value restored
4. Total Power Limit Restoration Point: Down Link Attenuator restoration condition is to restore by 1 dB Step from 3 dB less than “max. output power set-up value”
5. Total Power Limit Restoration Attenuator operation: restore Attenuator. up to the value
of “max. output power set-up value: 2” 6. Restore preferentially the changed Attenuator. value
RF Window Co., Ltd. | 32
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7. Once Attenuator. is restored, this routine ends .
6.4. Auto Recovery 6.4.1. Objective To restore Dual HPA when the down link path of Dual HPA is shutdown (S/W based Recovery feature).
6.4.2. Procedure 1. When Dual HPA is shutdown caused by over power until Down Link Path is in service
normally, CPU (in ICM) detects HPA shutdown and checks Down Link input level as well as the gain right before the shutdown.
2. Dual HPA(in Down Link Path) Shutdown condition on Re-Check 1. When “Down Link Input Level” + “Gain right before Shutdown” ≥ System output
power + 1dBm “Over Power” Alarm on
Recovery Condition 2. When “Down Link Input Level” + “Gain right before Shutdown” ≤ System output
power Over Power Alarm off
6.5. Up Link Auto Shutdown Mode 6.5.1. Objective To reduce unnecessary Up Link output power so that it minimizes influence to Base Station
6.5.2. Procedure 1. It is operated by Auto Shutdown mode 2. If Down Link output power is OFF, then it turns off Up Link output power (except
turning off by user) 3. When Up Link output power is OFF, it executes Amp Off alarm and reports Reason 4. If Down Link output power is ON by Auto Recovery feature, then Up Link output
power is ON as well
RF Window Co., Ltd. | 33
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
6.6. NMS Operation 6.6.1. Alarm Monitoring feature
1. Alarm occurs when alarm situation keeps on 10 sec continuously 2. Recovery is applied when alarm situation is not occurred for 10 sec continuously 3. Threshold Alarm : over and under each threshold is occurred and restored
6.6.2. LED Feature 1. POWER LED: Red LED is on when AC/DC Fail alarm occurred (Normal : Green) 2. DL ICM LED : Red LED is on when Down Link ICM alarm occurred (Normal : Green) 3. UL ICM LED : Green LED is on when Up Link ICM alarm occurred (Normal : Green) 4. RF LED : Red LED is on when RF module alarm occurred (Normal: Green) 5. Green LED is on when all is normal
RF Window Co., Ltd. | 34
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7. GUI 7.1. Program Overview This software provides status, control, download, and cancellation of ICS repeater. It is
easy to use with PC or laptop to install this program and to check a status of repeater for users.
7.2. PC Requirement
Item Minimal Requirement Recommended
Requirement
CPU Pentium-3 500Mhz Pentium-3 500Mhz ≤
Memory 128 MB 128MB ≤
Operating System Windows 2000 Windows 2000 ≤
USB essential essential
Resolution 800X600 1024X768
Program Size 1M 1M ≤
[Table - 11] GUI PC Requirement
7.3. How to Use 7.3.1. Program Installation
The file can be just copied and pasted to run the “ICS_REPEATER_VX.XX.EXE” File at any folder.
7.3.2. Program Start Double click or “Enter” key, “ICS_REPEATER_VX.XX.EXE”
RF Window Co., Ltd. | 35
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7.3.3. Window description
[Figure - 15] GUI Main Window
RF Window Co., Ltd. | 36
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7.3.3.1. Set up To setup Communication, repeater control, download, packet check, signal search and
communication cycle
[Figure - 16] GUI Communication setup
7.3.3.2. Status check It monitors the status of a repeater and it is placed the middle of program
7.3.3.3. Communication Status Status of Communication and connection
[Figure - 17] GUI Communication status window
7.3.4. Communication Setup 7.3.4.1. Connection
① Click on Connect Button.
② If the connection is normal, Status Bar that located bottom of main window will be displayed as below.
③ If the port is already occupied and can not be used, it gives Warning Windows with warning and error message.
7.3.4.2. Disconnection
① Click on Connect Button when communication connected.
② If communication connected, it will disconnect the communication and if communication
RF Window Co., Ltd. | 37
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
disconnected, it will connect the communication.
③ After Disconnection completed, Disconnect window will be display.
④ If communication disconnected completely, the status bar will be displayed as below.
7.3.5. Repeater Status 7.3.5.1. Repeater status run
① If “ICS_REPEATER_VX.XX.EXE” File is running and connected, the status window will be displayed
② Repeater Status
Item Status Remark
Red Alarm status
Green Normal status
Gray Initial Status
Values The Values display
On/Off Repeater on/off display
[Table - 12] Repeater Status details
7.3.6. Repeater Monitoring 7.3.6.1. System
Item Details Remark
ICS Maker Repeater manufacturer
Supplier Repeater supplier
Modem Maker Modem manufacturer
Amp Maker Down Link PAU manufacturer
Version Repeater System Version
Temperature Repeater Temperature
Over Temp Threshold value and status Alarm/Normal
Door Open Door status Alarm/Normal
RF Window Co., Ltd. | 38
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
In Power Mode In Power Mode On/Off status
Auto Shutdown Auto Shutdown On/Off status
Auto Recovery Auto Recovery On/Off status
[Table - 13] System Monitoring
The figure-20 shows the status of system
[Figure - 18] GUI System Status
RF Window Co., Ltd. | 39
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7.3.6.2. PSU
Item Status Remark
AC Fail AC status of Power Supply Alarm/Normal
DC Fail DC status of Power Supply Alarm/Normal
Battery S/W Battery Switch status Alarm/Normal
UPS Status When display shows a fault condition, alarm is activated Alarm/Normal
Low Battery When battery level is lower than 44 volts, alarm is activated Alarm/Normal
On Battery UPS is operating on battery power, alarm is activated Alarm/Normal
[Table - 14] PSU Monitoring
The figure-21 shows the status of PSU
[Figure - 19] GUI PSU Status
7.3.6.3. Down Link
Item Description Remark
Over Temp Amp Over Heat Alarm/Normal
DC Fail Amp DC on/off Alarm/Normal
VSWR Amp VSWR Alarm/Normal
Loop Fail Amp Loop Alarm/Normal
Device Fail Amp Device Alarm/Normal
Over Power Amp over output power Alarm/Normal
Amp On/Off Amp On/Off
Amp Temp Amp current temperature
Output Power Current output power
Input Power Current input power
Output Upper Output Upper limit Threshold and Output Power Status Alarm/Normal
Output Lower Output Lower limit Threshold and Output Power Status Alarm/Normal
Input Upper Input Upper limit Threshold and Input Power Status Alarm/Normal
Input Lower Input Lower limit Threshold and Input Power Status Alarm/Normal
RF Device RF PLL and LNA Status
Attenuation Attenuation Status
RF Window Co., Ltd. | 40
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
DSP Link DSP Connection Status Alarm/Normal
ICS Status Cancellation Status Alarm/Normal
Isolation Lack Isolation lack Alarm/Normal
Sys Isolation System Isolation Level
System Gain Current Gain Value
ICS Mode ICS Mode Control
Target Gain Target Gain Mode Setup Value
Total Power Limit Total Power Limit On/Off
[Table - 15] Down Link Monitoring
Following window shows setting parameter and input/output variation value in
downlink/uplink.
[Figure - 20] GUI Down Link setup status
RF Window Co., Ltd. | 41
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7.3.6.4. Up Link
Item Description Remark
VSWR Amp VSWR Status Alarm/Normal
Device Fail Amp Device Status Alarm/Normal
Over Power Amp Over Output power limit Alarm/Normal
Amp On/Off Amp On/Off Control status
Output Power Current Output power value
Input Power Current Input power value
Output Upper Output power upper limit value and output power
status
Alarm/Normal
Input Upper Input power upper limit value and input power status Alarm/Normal
RF Device RF PLL & LNA Status
Attenuation Attenuation Control status
DSP Link DSP Connection status Alarm/Normal
ICS Status Cancellation Status Alarm/Normal
Isolation Lack Isolation deficient Status Alarm/Normal
Sys Isolation Repeater Isolation Value
System Gain Current Gain Value
ICS Mode ICS Mode Control status
Target Gain Output power value of Target Gain Mode
Balance Offset Offset control status when ICS Mode sets to Gain
Balance Mode
Total Power Limit Total Power Limit On/Off setup status
[Table - 16] Up Link Monitoring
Following window shows setting parameter and input/output variation value in
downlink/uplink.
RF Window Co., Ltd. | 42
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[Figure - 21] GUI Up Link Setting Status
7.3.7. Repeater Control 7.3.7.1. Control Mode
① Select Control Icon in Function Setup
② Control Mode will be displayed
RF Window Co., Ltd. | 43
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[Figure - 22] GUI WCDMA (3G) Control Window
7.3.7.2. System Control
① By checking the Auto Shutdown, In Power Mode, Auto Recovery to turn on each function and un-checking the items to turn off.
② Input the value and press the enter key to setup Temp upper. ③ To make sure, information window will be displayed before the command is executed.
④ Click OK to setup. ⑤ Click Cancel to cancel setup. 7.3.7.3. Band Selection ① Check the box “FA (Carrier)”. ② FA (Carrier) is set up when select each FA
RF Window Co., Ltd. | 44
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
③ To make sure, information window will be displayed before the command is executed.
. ④ Click OK to setup.
⑤ Click Cancel to cancel setup.
7.3.7.4. FA Control ⑥ Check the box to ON and uncheck the box to OFF for FA and after finish checking, click
Apply to setup.
⑦ FA Allocation is set up when select Manual or Auto. ⑧ To make sure, information window will be displayed before the command is executed.
.
⑨ Click OK to setup. ⑩ Click Cancel to cancel setup.
7.3.7.5. Down Link Control ① By checking the box, Amp On/Off, Total Power Limit items will be ON and by un-
checking the box the items will be off.
② Output Upper, Output Lower, Input Upper, Input Lower, Attenuation, Gain Level input the value and press the Enter key to setup.
③ I For the ICS mode, simply select the item and will be set up. ④ To make sure, information window will be displayed before the command is executed.
RF Window Co., Ltd. | 45
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
⑤ Click OK to set up. ⑥ Click Cancel to cancel setup.
7.3.7.6. Up Link Control ① By checking the box, Amp On/Off, Total Power Limit items will be ON and by un-
checking the box the items will be off.
② Output Upper, Input Upper, Attenuation, Gain Level, Gain Balance Offset input the value and press Enter key to setup.
③ Select the item to setup ICS Mode. ④ To make sure, information window will be displayed before the command is executed.
⑤ Click OK to setup. ⑥ Click Cancel to cancel setup.
7.3.8. Control Item 7.3.8.1. System
Item Description Remark
Temp High Temp. Upper Threshold Value
Auto Shutdown Auto system report On/Off
In Power Mode Auto input power checking On/Off
Auto Recovery Auto Recovery On/Off
[Table - 17] System Control Item
RF Window Co., Ltd. | 46
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7.3.8.2. Down Link
Item Description Remark
Amp On/Off Amp On/Off
Output Upper Output Upper limit Threshold value
Output Lower Output Lower limit Threshold value
Input Upper Input Upper limit Threshold value
Input Lower Input Lower limit Threshold value
Attenuation Attenuation value for output power control
ICS Mode None, Target Gain Mode setting function
Gain Level output power value (Gain Mode)
Total Power Limit Output power limit On/Off
[Table - 18] Down Link Control Item
7.3.8.3. Up link
Item Description Remark
Amp On/Off Amp On/Off
Output Upper Output Upper limit Threshold value
Input Upper Input Upper limit Threshold value
Attenuation Attenuation value for output power control
ICS Mode None, Target Gain Mode, AGC setting function
Gain Level Output power value of Target Gain Mode
Balance Offset Value for Gain Balance Mode
Total Power Limit Output power limit On/Off
[Table - 19] Up link Control Item
7.3.9. Firmware Download 7.3.9.1. Download
① Select Firmware Download Icon.
② Firmware Download will be displayed
RF Window Co., Ltd. | 47
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
[Figure - 23] Firmware Download Window
7.3.9.2. How to Download ① Select ‘Open’ Button and the window will be displayed .
② Find the download file .
③ Select the download file and open it. ④ File name and file size will be displayed.. ⑤ When the file is selected and” Apply” is clicked, the processing bar will be displayed ⑥ When the bar is filled with the colors, the download is completed.
RF Window Co., Ltd. | 48
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7.3.10. Data Debugging 7.3.10.1. Debugging
① Select debugging icon in function setup
② Debugging window will be displayed. ③ Debug is to verify data transmitted via repeater.
[Figure - 24] GUI Debug Window
7.3.10.2. How to Debugging
① Check “on” in the on/off display window to set data display on. ② Clear button is to clear the collected data.
7.3.11. Feedback Signal Status Check 7.3.11.1. Run Feedback Signal Status Check
① Select firmware icon in function setup.
② Feedback signal status window will be displayed
[Figure - 25] Signal Status Window
RF Window Co., Ltd. | 49
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
7.3.11.2. Manual Request ① Click on request button to check feedback signal status once. ② Requested feedback signal status will be displayed the same as below.
③ Click on clear button to clear the display. ④ Feedback signal request for Down Link and Up Link is the same
7.3.11.3. Automatic Request ① Check on automatic poll to request the feedback signal status repeatedly. ② According to request, feedback signal status will be displayed
③ Click on clear button to clear the display ④ Feedback signal request for Down Link and Up Link are the same.
RF Window Co., Ltd. | 50
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
RF Window Co., Ltd. | 51
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
8. System Installation and Setup 8.1. Installation 8.1.1. Configuration
Item Specification
Repeater Cabinet ICS-W2137
DC IN Connector MS310A20-8P(6Pin male)
AC IN Connector MS3102A22S-2P(3Pin male)
Quick manual User Manual
[Table - 20] System Configuration
DC IN Connector MS310A20-8P(6Pin male)
Pin A : +27V
Pin B : EXT_+5V(Not use)
Pin C : EXT_GND(Not use)
Pin D : GND
Pin E : EXT_RX(Not use)
Pin F : EXT_TX(Not use)
[Table - 21] DC IN Connector Pin Assign
AC IN Connector MS3102A22S-2P(3Pin male)
Pin A : HOT
Pin B : NUT
Pin C : GND
[Table - 22] AC IN Connector Pin Assign
8.1.2. Installation - Locate repeater at necessary place and fix the bracket - Connector both antennas to Antenna Port
(DIN - Type Female Connector)
- Ground repeater - Supply the Electrical Power (AC100~260V) - Verify if Main Power LED if the connection is correct (Extension code can be used if
RF Window Co., Ltd. | 52
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
necessary, not included)
- Port Connection to Repeater is as follows
Item Function
DC IN
A: +27V D: GND
AC IN
A : AC 100V~260V+ B : AC 110V~260V- C : GND
Modem Port WCDMA Tx/Rx
Donor Port TX Input / RX Output
Service Port TX Output / RX Input
[Table - 23] System Connection Port
8.1.3. Check List before operation - Verify if all the connections are correct including Power Cable, RF Cables, Ground
and so on.
- Verify if Power Box (100~260V) is connected correctly. - Verify if RF Cables have correct connection regarding block diagram. - Verify if each module power and data cable have correct connection - Verify if Connection with Antennas is correct.
8.1.4. RF Monitor Port Donor Antenna Service Antenna
TX(To BTS) RX(from BTS) TX(To Mobile) RX(From Mobile)
15 dB Coupling 30 dB Coupling 40 dB Coupling -
[Table - 24] RF Monitor Port
RF Window Co., Ltd. | 53
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
8.2. Process of ICS Repeater setup and installation
[Figure - 26] Process of ICS Repeater setup and installation
RF Window Co., Ltd. | 54
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
8.3. Fault / Alarm Handling 8.3.1. Down Link / Up Link ALARM Handling
Module
Name Alarm Alarm Status Symptom and Action
Verify Donor Antenna Input Level High Input
Power
( DL / UL )
Alarm : Red
Normal : GreenAdd Fix Attenuator,
Use LNA Attenuator (RF Window)
Verify Donor Antenna Cable,
Antenna Direction,
RF Cables in Repeater,
Input level to ICS module
Low Input
Power
( DL )
Alarm : Red
Normal : Green
Replace cables, adjust ANT direction
Verify Gain and real output power using CPL
port
High Output
Power
( DL / UL )
Alarm : Red
Normal : GreenAdjust Gain
Verify Gain and real output power using CPL
port, Verify Each module In/Output
RF
Power
Low Output
Power
( DL )
Alarm : Red
Normal : GreenAdjust Gain, Replace the Module
Verify Isolation, Verify ICS Module defected.
ICS ICS (DSP)
( DL / UL )
Alarm : Red
Normal : GreenAdjust ANT Direction and GAIN. Replace ICS
Module
Verify PAU Input Level, Output Level using
CPL Port Over Power
( DL )
Alarm : Red
Normal : GreenAdjust GAIN
Verify if PAU not fixed, Verify if dust on a Heat
Sink . Verify if PAU defected. High Temp.
( DL )
Alarm : Red
Normal : GreenFix PAU, Replace PAU
Verify Output cable status, Verify if antenna
defected. Verify if PAU defected
DL
PAU
VSWR
( DL )
Alarm : Red
Normal : GreenReplace the defected Part
Verify if the Module defected RF
Device
RF Device
( DL / UL )
Alarm : Red
Normal : Green Replace the Module
RF Window Co., Ltd. | 55
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
UL
PAU
PAU
( UL )
Alarm : Red
Normal : Green
Verify if PAU defected.
Cable Connection Status
Replace the Module
[Table - 25] Down Link / Up link Alarm Handling
8.3.2. Environment Alarm Item Alarm Status Symptoms and Actions Remark
DOOR Status, DOOR SW operation
Check Door Open
Alarm
Alarm : Red
Normal : Green DOOR Lock and Updating SW
Verify AC Voltage AC Alarm
Alarm : Red
Normal : Green Re-construct AC Power
Verify if PSU output is 27V DC Alarm
Alarm : Red
Normal : Green Replace PSU
Verify Housing Temp. Housing
Temp
Alarm
Alarm : Red
Normal : Green
[Table - 26] Environment Alarm
RF Window Co., Ltd. | 56
ICS Repeater ICS-W0837B User Manual
ICS-W0837B User manual/Confidential & Proprietary
9. Manufacturer Information
RF Window co. ltd. Maker : RF Window Co., Ltd
Address: 14F, Daerung Posttower3, 182-4, Guro-3dong, Guro-gu, Seoul, 152-847, South Korea
TEL: +82 –2- 2082-1250