User Manual for V3_0_SDVR

8/2/2019 User Manual for V3_0_SDVR

1/141

0

Embedded Digital Video Recorder

User Manual


2/141

1

Preface

Thank you for selecting our products, we will offer the highest-quality services to you wholeheartedly.

This user manual will take the type of channel 16 as the model, to give the introduction on the using of the

machine and the processing of the problem.

The contents of this user manual is only for reference, please forgive that we won t separately provide any

information about the updating. The contents of updating will add to the newly edition and we will offer the

newest manual in the download center of our company's website at the same time. The user manual may include

the inaccuracy or misprint on technology, we sincerely hope you can give the feedback to us in time and we will

substantiate or improve in the subsequent editions.


3/141

2

The Front Panel


4/141

3

Page number Page number

1. Trademark 19 .Cl ear 34

2. SATA disk port 36 20 .E xi t 34

3. Login/Lock 36 21.Up 35

4. Scene format 35 22.D own 35

5. Scene switch 35 23.Left 35

6. Infrared remote control receiver 36 24. Righ t 35

8. Record 34 25. Ent e r 35

9. P layback 34 2 6 3 4 . Da t a k e y 1 9 33

10.Menu 34 35. 0 33

11.Backup 34 36. . / : 33

12. Informat ion 34 37.PIP 33

13.P lay/p ause 35 38. Power 36

14.Fast backward 35 3 9 . P o w e r L E D P W R 3 2

15.Fas t forward 35 40. Hard disk LED HD D 33

16.Frame 35 49. Record LED RE C 33

17.Page up 34 5 0 . In f r a re d LED I R 33

18.Page down 34 52. Upda te LED Update 11 4


5/141

4

The Back Panel


6/141

5

Page number Page number

1.Video input port 26 8. RS-485 port 32

2.Video output port 26 9. 12V power 28

3.Audio input port 27 10. RJ45 Ethernet port 27

4.Audio output port 27 11. LINK 27

5. Alarm input port 28 12.ACT 27

6.VGA output prot 27 13. Port to earth

7. Alarm input port 28


7/141

6

Base operation instruction

1Turn on

Press the power button on the back panel, the front panel boots up first, and the system stands by. Press the button on the front panel or the

remote controller for 2 seconds, the system will run.

2Turn off

Press the button on the front panel or the remote controller then input the power password (default: 000000) and press Enter. When you

hear a beep, the system has shut off and stands by.

3Update

When the system is standing by, press the button on either the front panel or the remote controller for about 6 seconds. When you hear a

beep, input the right update code (default: 666666) and after pressing the Enter key, system will turn to update condition. (On 4.13 update by

software , you can find the detailed process of update.)


8/141

7

Catalog

Charpter1 Brief Introduction about the DVR .................................................................................................. 11

1.1 Summarization.......... .................................. ................................. .................................. ................................. ........11 1.2 Application Scopes..................................................................................................................................................12

Charpter2 Specifications and Main Functions .................................................................................................13

2.1 Specifications..........................................................................................................................................................13 2.2 Main Functions ............................. ................................. .................................. ................................. ......................15

Charpter3 Equipment Installation and Illustration........................................................................................... 23

3.1 Installation Environment and Cautions...................................................................................................................23 3.2 Package Checking...................................................................................................................................................25 3.3 The Back Panel instructions....................................................................................................................................26

3.3.1 Video Connection............................................................................................................................................................... 26

3.3.2 Audio Connection ..............................................................................................................................................................27

3.3.3 VGA Connection................................................................................................................................................................27

3.3.4 Ethernet Connection........................................................................................................................................................... 27

3.3.5 Alarm Input/Output Connection......................................................................................................................................... 28


9/141

8

3.3.6 RS-485 Connection ............................................................................................................................................................32

3.4 Details of the Front Panel .............................. ................................. .................................. ................................. .....32 3.5 Infrared Remote Controller (IRC) ............................. .................................. ................................. .......................... 37

3.5.1 IRC Layout.........................................................................................................................................................................38

3.5.2 Details of IRC.....................................................................................................................................................................40

Chapter4 System Operation .............................................................................................................................44

4.1 Login and Lock.......................................................................................................................................................44

4.1.1Keystroke Lock/Unlock.......................................................................................................................................................44

4.1.2 System Login......................................................................................................................................................................45

4.1.3 System Lock.......................................................................................................................................................................46

4.2 Video Parameter Setup............................................................................................................................................46

4.2.1 Channel Video Parameter Adjusting...................................................................................................................................46

4.2.2 Picture in Picture ................................................................................................................................................................47

4.3 User Setting .............................. .................................. ................................. .................................. ......................... 47

4.3.1 Add User.............................................................................................................................................................................48

4.3.2 Modify and Delete User .....................................................................................................................................................50 4.4 Record and Alarm schedule ................................. .................................. ................................. ................................ 50

4.4.1 Record Parameter Setting ...................................................................................................................................................51


10/141

9

4.4.2 Manual Record...................................................................................................................................................................55

4.4.3 Time Record....................................................................................................................................................................... 56

4.4.4 Motion Detect (MD) Record..............................................................................................................................................59

4.4.5 Alarm Record.....................................................................................................................................................................61

4.5 Playback Operation.................................................................................................................................................64

4.5.1 Playback by Time...............................................................................................................................................................64

4.5.2 Playback by File.................................................................................................................................................................65

4.6 Backup Operation .............................. .................................. ................................. .................................. ................66

4.6.1 Data Backup....................................................................................................................................................................... 67

4.6.2 Playback the Data............................................................................................................................................................... 69

4.7 PTZ and Channel Setting ............................. ................................. ................................. .................................. .......69

4.7.1 PTZ Setting ........................................................................................................................................................................ 70

4.7.2 Channel Setting..................................................................................................................................................................71

4.8 System Parameter Setting .............................. .................................. ................................. ................................. .....72

4.8.1 System Time.......................................................................................................................................................................72

4.8.2 System Password................................................................................................................................................................ 73 4.8.3 Default Setting ................................................................................................................................................................... 76


11/141

10

4.9 Information...... .................................. ................................. .................................. ................................. ................. 78

4.9.1 Current Alarm Information.................................................................................................................................................79

4.9.2 System Information ............................................................................................................................................................80

4.9.3 Disk Information ................................................................................................................................................................81

4.9.4 Recording Status.................................................................................................................................................................83

4.9.5 System Logbook.................................................................................................................................................................85

4.10 Disk Management.................................................................................................................................................87 4.11 Network Setting ................................ ................................. .................................. ................................. ................ 88

4.11.1 Simple Network Setting....................................................................................................................................................89

4.11.2 WAN Setting.....................................................................................................................................................................91

4.12 IE Operation Instructions......................................................................................................................................94

4.12.1 LAN operation Instructions ..............................................................................................................................................94

4.12.2 WAN operation Instructions ...........................................................................................................................................102

4.13 Software update ................................. ................................. .................................. ................................. ............. 112 4.14 Cut Out to Resume................................ .................................. ................................. .................................. ......... 115

Appendix 1: FAQ & Answers for DVR ......................................................................................................... 116


12/141

11

Charpter1 Brief Introduction about the DVR

1.1 Summarization

Digital Video Recorder (DVR) is a combination of VCR, video switcher, quad, video controller, video server and remote data transmission

system, it can connect alarm sensor and alarm buzzer to build up an alarm system, it also can use for image motion detection, PTZ controlling through

decoder, network video transmission and signals controlling. Compared with the traditional analog monitor system, DVR has much more powerful

functions, conveniently monitor network. Digital video recorder is the new trend of the development in safety; it will soon replace the traditional

analog monitor system.

DVR is a kind of special embedded digital video recorder that is professionally designed for multi-media digital monitor system. They are

especially used in environment when long-time audio and video recording, remote monitor and controlling needed. It adopts the integrated design and

integrates many functions such as: video and audio frequency capturecompressstorenetwork transmissionmultiple PTZ controlalarm system

in a single PCB board to ensure the high integrated level and stability of the system. It offers many kinds of network port, uses the TCP/IP protocol to

connect the LAN and WAN to make you can monitor and record the image anywhere. The operation is simple and the application is wide.


13/141

12

1.2 Application Scopes

The main application of the DVR is as follow:

The digital video storing (Replace the simulative recorder) Network monitor system of bankATMfactory Traffic monitoring system on freewaybridge and tunnel. Monitoring management system of intellectualized high-rise and community Unmanned guarding system of electric power station and telecom station Intellectualized access guarding system (motion record) Monitoring the pipelining of manufacture and warehouse Providing the long-distance service for school, nursing place and kindergarten Out-of-doors equipment monitoring system Availably monitoring and recording traffic vehicle to ensure the public safety Playback pre-recorded VCDDVD and other TV programs on traffic vehicle


14/141

13

Charpter2 Specifications and Main Functions

2.1 Specifications

Parameters of videoVideo inputPAL625 L/F, 25F/S NTSC525 L/F, 30F/S

compound video inputBNC port1VP-P,75

Video outputPAL625 L/F, 25F/SNTSC525 L/F, 30F/S

A composite video outputBNC port1VP-P,75

A VGA output (frequency60HZresolution rate1024*768)

Parameters of audioAudio input lotus20-100mv, 10K

Audio outputan audio outputlotus20-100mv, 1K

Compression Formatvideo compressionH.264audio compressionG.722


15/141

14

Image resolution rate: real-time display (704*576), VGA output 1024*768Video compression CIF352*288Half-D1(704*288)

Audio sampling rate: 8K sampling point per second16 bit per sampling point Record definition: HD1CIFl

Image quality: There are six in all, from high to low (1, 2, 3, 4, 5, 6) Record video file size as follows (only for reference):

Half-D1: quality 1-350M/H2-250M/H3-200M/H4-160M/H5-130M/H6-100M/H

CIF: quality 1-150M/H2-100M/H3-80M/H4-70M/H5-50M/H6-40M/H

Operating system: Embedded real-time operating system (RTOS) Port of the hard disk: PATA, SATA Port of I/O: RS485, alarm input/output Port of the network: Adaptive Ethernet port of 10M/100M Power supply: 220 30% V, 50 3% HZ

11020% V603% HZ optional


16/141

15

Consumption of the machine (without hard disk):30W8 Channels: definition is HD116 Channels

20W4 Channels

25W8 Channels: definition is CIF

Dimensions: Width 440mm, depth 436mm, height 96.2mm2.2 Main Functions

This series embedded digital video recorder adopts high performance the embedded real-time multiple operating system (RTOS) and embedded

processor, so setup a monitor system perfectly. All the codes are embedded in FLASH that the system is steadier and will not be interfered by the

external factors such as virus etc. it also can work steadily for a long time under the abominable environment and under the situation with no guard.

Compress Function1. Support PAL/NTSC4. 43/NTSC3. 58 video signals;2. The video compression is H. 264, supporting VBR as well as VFR;3. Setup video picture quality and compression yard;


17/141

16

4. Separately compress each audio signal stream, the compressed audio standard adopts G.. 722, the sampled point is: 8K sampled point / second,16bit / sampled point;

5. Compound H.264 data stream is formed after compressing video and audio signal, the video and audio keep moving simultaneously and can set upno audio record when playback;

6.

Support double data stream technology;

7. CIF/Half _ D1/D1: there are lowmiddlehigh three kinds of definition available;8. 6 kinds of record image quality for choosing, users can select video quality according to the need that specifically, so as to ensure for enough longvideo time.

Network Function1. Support TCP/IP agreement (support ARP, RARP, IP, TCP, PPPOE, DHCP, etc.)2. Support PPPOE and dialing automatically (PPPOE) again at the same time and support domain name mapping3. Complete network end with controlling instructions (users can take control of the DVR from Internet)4. Can use the special software or Internet Explorer browser to set up parameter through the network, look around monitored scenes of any or morethan No. 16 video and audio signals in real time, and PTZ as well


18/141

17

5. Embedded multiple communication protocols, can control PTZ in the end of the host computer and control PTZ and scene through network6. Update through network and achieve long-distance safeguard to help user upgrading for the future maintain and expanding the functions Record Function1. Support: Manual video, timing video, motion detection and warning video2. Support the categorized search of manual video, timing video, motion detect and warning video contents3. Motion detection function: Each video can set up multiple dynamic measuring areas and offer 10 sensitivity grade 4. Full screen shielding switch, can achieve the whole shielding of real-time picture and record wont be shielded when the whole shielding video5. Warning record video supports single way or multi-way record individually6. Client PC can record compressed data stream, support record audio and video signals into the computer directly by Internet7. Support No.1 to 16 recording on videotape real-timely, each video parameter can setup alone8. Support the titles, recording times and dates adding9. Support record modes (manual videotiming videomotion detection video and warning video) checking Playback Function1. Current playback: accurate time playback, searched playback the contents of manual videotiming videomotion detection video and warning


19/141

18

video

2. Support picture in picture playback3. Support monitoring and showing pictures at the same time and make no influence to the video content in real time4. Support the playback modes of 4 ranks of speeding, slowing, playback, pausing, forwarding5. Can reach 8 channels video playback modes through using client manager and make no influence on the real-time picture and video result. Monitor in Real Time Function1. Support the local monitor and VGA;2. Support the regulation of each video parameter (luminance, contrast rate, color, degree of saturation);3. Show the mode (1 / 4 / 9 / 16 channels) switch rapidly, no delaying;4. Embedded multiple communication protocols, can control PTZ and scene through the frontal board or remoter;5. The function of detection to the dynamic video, each video can setup 64 dynamic measuring area (Each video of H6016A8H6108H6008A4 cansetup 560 dynamic measuring area), offering 10 sensitivity grade

6. Offer full screen shielding switch, can achieve the whole shielding of real-time picture, record wont be shielded when in full screen shielding;7. Support the video playback and real-time monitoring at the same time;


20/141

19

8. Support the picture poll, can setup poll and poll spacing interval freely according to the need;9. Possess WEB SERVER function, support dynamic IP and domain name parse;10.Can use client software or Internet Explorer browser to look through each channel or 16 channels video and audio signals in real time at most;11.Support talkback between managing host computer (control center) and network hard disk video recorder (front);12.Support TV wall function. Storing and Backup Function1. 8/16 channels host computer equip 4 IDE ports separately, can drive 8 IDE hard disks at the same time, the hard disk supports 48bit LBA workpattern (namely great hard disk work pattern)(Annotate4 channels host computer equip 4 SATA ports, can drive 4 SATA ports hard disks working)

2. 4/8/16 channels host computer offer a special port of SATA for backuping, support hot insert and drawing the hard disk under starting state;3. Possess powerful functions of management to hard disk, support automatically dormancy;4. Support formatting the hard disk under normal running state;5. Support the dormancy of the hard disk. The number of the working hard disk cant exceed 2 at most at one time;6. Recycling and non-recycling mode available;7. Standard FAT32 file format, the video file can be discerned in PC system and broadcasted after installing the random CD;


21/141

20

8. Local backup: backup into the embedded video recorder directly, support hot backup by SATA port when switch on the DVR(support hot insertand draw the hard disk)

9. Remote backup: backup all HDD files by client manager softwarebackup HDD files in special time periods backup specific cameras HDDfiles in specific time periods.

Alarm Measure Function1. Local alarm: video loss alarm, motion detection alarm, sensor alarm, HDD space lacking alarm, video abnormal check and HDD error detect2. Remote alarm: video loss alarm, motion detection alarm, sensor alarm, which can transmitted to client through remote internet, can achieve toautomatically open motion detection video

3. Video loss alarm, motion detection alarm and sensor alarm signals can connect to mobile telephone, beep-pager or normal phone (e.g.: 110)4. Remote PC buzzer alarm (the alarm signal is uploaded), can achieve the picture of warning channel is maximized automatically Security Guarantee1. Adopting 32-bit embedded microprocessors and embedded real-time operating systems, which ensures high real-time security, dependability andstability features

2. Complete video data inquiring function (sensor alarm log, motion detection log, remote login log, record parameter changing log, update log,


22/141

21

playback log, system start log and backup log)

3. System lockup, password examining, multiple users authorize (support 16 users)4. Video loss alarmmotion detection alarmsensor alarm can connect to mobile telephone, beep-pager or normal phone (eg:110)5. The Internet alarm linkage (the alarm signal is uploaded)6. Encrypt the code of user name, password and code transmission7. Watchdog function, system can automatically self-check when there is disorder and restart automatically at once to initiate the working state. Complete Input/Output Port1. Internet port of RJ45 in common use2. SATA port at a high speed, more convenient to connect. The transmission speed of data is faster than USB port3. Control the panel button to operate easily4. Remote controller controls multiple host computers or single one5. Complete remote controlling commands by client manager software, and PTZ controlling6. Support two kinds of output ways: Composite signal output and VGA output7. Available Input/output rule (PAL/NTSC4. 43/NTSC3. 58), support switching over the Chinese/ English menu


23/141

22

8. RS-485 ports, PC can control the serial equipment through the transparent channel of Internet hard disk video recorder9. Support serial port HDD10.4/8/16 channels host computer offer 4/8/9 channels alarm input separately, 2/2/4 channels alarm output. Development SupportOffer SDK development package for client managing device.


24/141

23

Charpter3 Equipment Installation and Illustration

3.1 Installation Environment and Cautions

Installation Environment

Normal working temperature is -10C--55C, storing temperature is -10C--70C; The equipment must keep horizontal either on installing or on using; Avoid installing in high temperature or humidity conditions; Heat release fans are placed for cool down, so you should put the device on ventilated place. The back of DVR should be placed 6cm away from the other device or wall when intallatin; Moving the DVR between two places with high difference in temperature will shorten the using life; Please install the lightning conductor when the machine is used in frequent thunder areas.


25/141

24

Cautions

Avoid wet touching the power switch or the DVR; Make sure the machine and its case are grounded (There is an earth port on the back panel of the machine);

Be sure the stabilization of electric power and pressure, avoid cutting off the chief switch;

Avoid dropping liquid or metal into machine that may cause short circuit or fire; You cant record or playback until you install at least one HDD correctly; Short circuit would happen when the dust on the board is affected with damp, so you have to brush the board and other accessories termly tomake the machine to work normally for a long time;

There are 3 IDE ports on one hard disk cable, the longer one should be inserted on the main board and the others on the hard disks; If you want put two disks on one disk cable, you have to set a master disk and a slave one; After installing, machine can automatically detect hard disk. If an unformatted hard disk is detected, system will prompt you whether to formatthe disk (System supports formatting hard disk, no need of PC). If the disk is used before, please delete the partition with PC, or there will be error.

The system only supports the FAT32 file format;


26/141

25

When hot plugging the SATA hard disk, please plug in/out the data line and power cable together; Dont make hot plugging to any other hardware except the ones that support hot plugging; The ports of audio and video and the RS-485 cant insert or draw when the power is still on, or the equipment will be damaged easily; Please use the button on the front panel instead of switching off the power directly when turn off the DVR, so that the hard disk won t bedamaged.

In order to keep the integrality of the records, you should change the damaged disks. (There are informations about the error of the disk in thelogbook.)

3.2 Package Checking

After unpack, please check the machine whether it has out of shape or other damages. If something is wrong, please stop using it and get in touch

with your suppliers. Please read and keep the informations carefully.

The accessories are as follows:

User manual *1 Infrared remote controller*1 Batteries*2


27/141

26

Quality certificate*1 Product maintenance card*1 Connecting wires of hard disk (8/16 channels DVR with 4 IDE cables, 4 channels DVR with 4 SATA cables) Power cable*1 Installation accessories*1 Client manager software CD*1 47K resistance (The quality of the resistance is corresponding with the alarm inputs of the machine.)

3.3 The Back Panel instructions

3.3.1 Video Connection

The video inputs are corresponding with the model of DVR. And there is a video output. All the video ports are normal BNC connectors and the

sigals are normal composite video signals. Each channel has its corresponding silk-screen on the back panel.


28/141

27

3.3.2 Audio Connection

The audio inputs are corresponding with the model of DVR. And there is an audio output. All the audio ports are normal lotus connectors. Each

channel has its corresponding silk-screen on the back panel. The input impedance of audio is 10K and the output one is 1K.

3.3.3 VGA Connection

There is a VGA output on the back panel, which is used in the occasion of high definition. Its resolution rate is 1024*768 and refresh frequency

is 60 HZ.

3.3.4 Ethernet Connection

There is a 10M/100M adaptive Ethernet port which is used to connect the PC and the DVR, the indicator lights ACT and LINK are used to

indicate current network status.

LINK (Network speed indicator) On100M off10M

ACT (Send/Receive data indicator) BlinkSending/Receiving data


29/141

28

3.3.5 Alarm Input/Output Connection

Alarm inputInput resistance 22K, window compare voltage (3.0 V~4.18 V)

(annotatethere will be alarm when the voltage between 0V-3V or 4.18V-12V, and no alarm when the voltage between 3V-4.18V )

Alarm output: Relay node output is 120 VAC/1A, the largest diversion voltage is 250VAC/30VDC, and the largest diversion electric current is

7A. Normal (relay open), Alarm (relay close)

Sensor power: The machine provides a +12V DC power output port.

The connection of sensor for alarm: (It is a sketch map only)

1. Normal close connection

In this situation, resistance and the inductor should be in series connection (resistance, the positive pole of the DVR power, DVR alarm input

port, the positive pole of the inductor should be in series with the alarm output of the inductor, and the circuitry inside the inductor is close in the

status.) The voltage between GND and the alarm input is 3V 4.18V. When receiving induction from outside, the circuitry open, alarm is on. Then

the circuitry close immediately and waiting for the next induction.


30/141

29

2. Normal open connection

In this situation, resistance and the inductor should be in parallel connection. The resistance, the positive pole of the DVR power and the alarm

input are connected directly, and power input port of the inductor, alarm output of the inductor are in series with the positive pole of power and alarm


31/141

30

input port of the DVR. In the case, circuitry inside the inductor is open, the voltage between GND and the alarm input port is 3V 4.18V. When

receiving induction from outside, the inductor close, alarm is on. Then the circuitry open immediately and waiting for the next induction.


32/141

31

The connection of alarm output:

Take 12V sensor connection for example.


33/141

32

3.3.6 RS-485 Connection

There is a standard RS-485 port on the back panel, which is used to control the PTZ decoder and the PTZ camera.

Support multiple communication protocols of PTZ decoder or PTZ camera. One piece of DVR can be connected to many PTZ decorders or PTZ cameras, each channel with a PTZ decorder or camera The default address is corresponding with the channel number, channel 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16s address is1, 2, 3, 4, 5, 6, 7, 8, 9,10, 11, 12,13, 14, 15, 16

Please set use RS485 device which you can find in the Network interface on when you want several pieces of DVR to control a PTZ at onetime

3.4 Details of the Front Panel

1. LED area Power LED PWR:

When the system is running, it is on, otherwise off.


34/141

33

Infrared LED IR:When infrared signal is receiving, it is on, otherwise off.

Hard disk LED HD/HDD:When the hard disk is working, it is on, otherwise off.

Record LED REC/Rec9:When it is recording, it is on, otherwise off.

2. Keystroke areaThere are 34 buttons on the front panel.

Digital area 12ABC3DEF4GHI5JKL6MNO7PQR8TUV9WXYZ0 ./: PIP 09Used to input digit/character or switch the scene by keyboard shortcuts. When the menu is not visible, 1~9 digit button switches the

output scene to the channel 1-9. 16 channels machine switch to channel 1016 route by . /: and number key.

. /: Used to input .orwhen inputting IP or time, and switch the two images of the PIP. Besides, it can input number key 10 in the 16channels machine.

PIPUsed to switch between Chinese/English input modes when you set the channel option or change the image to picture in picture.


35/141

34

Menu areaRECPLAYSETCOPYINFO

RECManual record menu

PLAYPlayback menu

SETSetup menu

COPYBackup menu

INFOInformation menu

Menu operation area-+

-figure subtractmenu turn over.

+figure addmenu turn over..

: Delete

Exit.

Cursor moves, PTZ control.


36/141

35




Menu enters.

Scene display area

Switch 1/4/8/9/16 scenes format whether the video is real-time or playbacking.

Switch current channel.

Playback area

Play or pause playback.

Fast forward.

Fast backward.

frame by frame.


37/141

36

Power swichUsed to start or shut off the system.

LockUsed to login or lock up system.

3. SATA hard disk port areaAttention when hot-plugging the SATA disk: do plug the data line and power cable at the same time. Commend the order of hot-plug SATA hard

disk: when insert the disk, insert the power line first, and then the data cable; when pull out the disk, pull out the data cable first, and then the power

line.

4. Infrared receiving areaPlease face the remote controller directly to this area while you use the remote controller so that the signal could be well received.


38/141

37

3.5 Infrared Remote Controller (IRC)


39/141

38

3.5.1 IRC Layout

1. Login/Lock 25. Up2. Power 26. Down3. Record 27. Left4. Playback 28. Right5. Setup 29. Return6. Backup 30. Enter7. Scene format 31. Zoom-8. Scene switch 32. Zoom+9. DN 33. Focus+10.PIP 34. Focus-11.One 35. Iris+12.Two/ABC 36. Iris-


40/141

39

13.Three/DEF 37. Reset14.Four/GHI 38. Call15.Five/JKL 39. Auto16.Six/MNO 40. Mute17.Seven/PQRS 41. Clear alarm18.Eight/TUV 42. Play\pause19.Nine/WXYZ 43. Fast backward20. ./: 44. Fast forward21.Zero 45. Frame22.Delete 46. Information23.Page up 47. F124.Page down 48. F2


41/141

40

3.5.2 Details of IRC

Digit area 12ABC3DEF4GHI5JKL6MNO7PQR8TUV9WXYZ0 ./: PIP 09Used to input digit/character or switch the scene by keyboard shortcuts. When the menu is not visible, 1~9 digit button switches the output

scene to the channel 1-9. 16 channels machine switch to channel 10-16 by . /: and number key.

. /: Used to input .orwhen inputting IP or time. It can input number key 10 on the 16 channels machine. PIPUsed to switch between Chinese/English input modes when you set the channel option or change the image to picture in picture. Menu function area

RECPLAYSETCOPYINFO

RECManual record menu

PLAYPlayback menu

SETSetup menu

COPYBackup menu

INFOInformation menu


42/141


43/141

42

Switch current channel.

Playback function area

Play or pause record.

Fast forward.

Fast backward.

: Playback frame by frame.

PTZ and camera control areaZOOM-ZOOM+FOCUS-FOCUS+IRIS-IRIS+RESETCALLAUTOF1 F2

ZOOMAdjust camera zoom.

OCUSAdjust camera focus.

IRISAdjust camera iris.

RESET

Save the current location of the PTZ.

CALLLoad reset of PTZ.


44/141

43

AUTOLet the PTZ rotate automatically.

F1Light control.

F2Brush control.

CLEARCLEAR: Clear alarms.

MUTEMUTETurn on/off system audio.

Power swichStart up or shut down the system.

LOGIN/LOCKLOGIN/LOCKLogin or lock system.


45/141

44

Chapter4 System Operation

4.1 Login and Lock

In order to discern every user's authority, prevent users from going beyond one's commissionusing some functions and influencing the normal

work of the system, we specially set up the login and lock function for system.

4.1.1Keystroke Lock/Unlock

The option Keylock is under the network interface. After making the option on and storing the change, press the DN on the remote controller

to lock the keystroke. In this situation, all of the keystroke on the remote controller and front board are locked but the power key.

The method of releasing the keylock is to press the DN key on the remote controller, input the corresponding DN (DN can be set by yourself,

the range is 099,and the primary DN is 33. When you forget the device number, you can reset the code operation, because this operation will make

the Keylock unavailable. Code reset operation meet the 4.9.2the on/off code set), and press enter key, so all of the keystroke on the remote

controller and the front panel are released and can be used normally. When you dont set the Keylock, the remote controller and the front panel can


46/141

45

be used normally.

4.1.2 System Login

When the system is in the state of locking, press the button on the front panel or the LOGIN/LOCK button on the remote controller for

about 1 second, the interface of login will appear as follows

Input user name and password on the login interface (distribute in authority in advance), after you input correct user name and password and

press ENTER, the sign on the lower left corner will switch to User automatically, and show the user name of current user nearby. Then

you can carry on the operations in your own authority.


47/141

46

About the input:some keys of number can input characters when edit,for example: press the key 2 for 7 times, the display will be 2,A,B,C,a,b,c.

4.1.3 System Lock

When the system is in the state of loginif there is no operation in 5 minutes or you press the button of the front panel or the

LOGIN/LOCK button on the remote controller for about 1 second, the sign User on the lower left corner will switch to automatically.

You can only do the operations such as loginset DN and switch scene format and so on at the moment.

4.2 Video Parameter Setup

4.2.1 Channel Video Parameter Adjusting

The video parameter of each channel can be adjusted in order to adapt to different environments. The adjustable parameter is: brightness,

contrast, saturation and hue.

Method: After login, choose the channel you want to situation, the current channel is on the upper left corner. In the situation of PIP, it is the

greater one. You can press the on the front panel or the remote controller to turn on the video parameter state bar. And through the , you


48/141

47

can switch the four parameters. The regulation of the parameter state is through the and the buttons, the anterior one is to add, and the

posterior one is to subtract. The ENTER button is used to resume to default setting. (Pay attention: The system will keep the setting automatically

after 8 seconds, and it would not influence any other operations.)

4.2.2 Picture in Picture

This function is transferred by the PIP button. The key ./: is used to switch the two pictures. And the is used to switch the place of the

small picture.

4.3 User Setting

The way to enter the user account interface: After login, through SETUPSystem Code continuous button operations to enter the user

account interface, the interface is as follows:


49/141

48

If you select the User list at login, you can use the -+buttons to select the user name without inputting character by character.

4.3.1 Add User

Only the administrator (admin) has the right to add account. When system is at the User Account interface, focus on the Add Icon and

press ENTER to enter the Account add/modify interface. The interface is as follows:


50/141

49

Then you can input the user namepassword and corresponding permission you want the user to have. The method of endowing permission:

Move the cursor to the icon and press ENTER, you can see a red appear in the round button, which means you have chosen the function. After

finishing setting up, focus on the Modify...icon and press ENTER. (Its important, if you dont follow this step, you wouldnt add the user

successfully.) And when you exit the setup menu, system would prompt you to save the changes, press ENTER, and you have succeeded in adding


51/141

50

the new account. (Attention: System allows 16 accounts at most.)

4.3.2 Modify and Delete User

What should first explain is that: Only the administrator (username is admin) can modify users' authority and delete users. Users can only modify

their own password. The method of modifying or deleting users is to move the cursor on the account name to be dealt with on User account

interface, press ENTER once to choose the user. If you want to modify the user's authority, press ENTER once again to enter the Account

add/modify interface to modify user's authority (Attention: After finishing modification, focus on the Modify...icon and press ENTER.)Return to

save changs after finishingIf you want to delete a user, choose the users name in User account interface, focus on Delete...and press ENTER

to delete the user.

4.4 Record and Alarm schedule

Explanations for controlling record:

The system has 4 record trigger ways: Manual record Time record Motion record Alarm record. The priority of the 4 ways is from

low to high. Whether a certain channel is at the state of recording is synthetically based on the 4 record ways. System will open the channels record


52/141

51

as long as any of the 4 ways is on.

4.4.1 Record Parameter Setting

Record parameter will not change along with the way of record. So its important to set the record parameters before recording, for it concerns

with the definition of record and the disk space that the record would use. After login, through SETUPParam continuous button operations to

enter the record parameters interface. The interface is as follows (Take the 16 channels machine for example):


53/141

52

Over Write modeIts used to select the over write mode of HD: Auto or Manual, and it would simultaneously affect all the channels.

1Auto: When the hard disk is recorded fully, this mode will automatically overlay the oldest record files.

2Manual: When the hard disk is recorded fully, this mode will automatically prompt you whether to overlay the oldest record files or change

the HD (Note: there will be no records during the period that from flipping cue to pressing ENTER. So in order to prevent record losing, we dont


54/141

53

commend you to choose Manual.)

LanguageSystem provides two languagesyou can choose the language according to your personal need.

After you change the language, system will prompt you to reboot. The setup wouldnt take effect until the system has rebooted.

Color SystemThere are three color-systems. You can select the suitable one according to the nation where you are.

1PAL (Chinese/Britain) The upper limit of the frame rate is 25 F/S.

2NTSC4.43 (USA) The upper limit of the frame rate is 30 F/S.

3NTSC3.58 (Taiwan) The upper limit of the frame rate is 30 F/S.

After you have set the color system, system will prompt you to reboot. The setup wouldnt take effect until the system has rebooted.

Date SuperposesIts used to whether to superpose date on the video while recording or not. The superposed position is: When the time and the date are selected to

superpose at the same time, the date is in the lower right corner (occupies the left ) of the imageAs only date superposes, it is in the middle of the

botton of the image.


55/141

54

Time SuperposesIts used to whether to superpose time on the video while recording or not. The superposed position is: When the time and the date are selected to

superpose at the same time, the time is in the lower right corner (occupies the right ) of the imageAs only time superposes, it is in the middle of the

botton of the image.

Image PollIts used to whether to use image poll or not while it is at the state of real-time video. And you can set the polling intervals after you select this

option.

ResolutionThe resolution is divided into two grades.

(1) High: It means the grade of level is Half-D1 and the resolution rate is 704*288.

(2) Low: It means the grade of level is CIF and the resolution rate is 352*288.

QualityIts used to choose the video quality (123456 ) of the r ecord, and the quality would decrease according to the increase of the figure.

Frame rate


56/141

55

Its used to set the video frame rate of each channel: When it is PAL, 2 to 25 is availableWhen it is NTSC, 2 to 30 are available.

AudioIt is a switch that whether to record with audio or not. (With red hook means on, without red hook means off.)

4.4.2 Manual Record

The way to enter the record interface: After login, press REC key to enter the record interface, the interface is as follows (take the 16 channels

machine for example):


57/141

56

Move cursor on the icon that you want to operate, press ENTER to choose or reject the icon. As the icon turn yellow, the state of manual

record is open. Otherwise, the state is close. The setup wouldnt take effect until you move the cursor to the OK icon and press ENTER button of

the remote controller or the front panel.The button between OK and Cancel is for selecting all channels.

You can directly control the manual record through the record menu. Once the manual record of any channel is started, the channel will be in

state of recording immediately, and it has no concern with the settings of other record ways (Time/Motion/Alarm).

4.4.3 Time Record

The way to enter the time record interface: After login, through SETUPTimeRec continuous button operations to enter the time record

interface, the interface is as follows (take the 16 channels machine for example):


58/141

57

Move the cursor on the On icon corresponding with the channel you want to operate, press ENTER to enter the time record schedule

interface. And the interface is as follows:


59/141

58

You can set two time periods for time record of every day, or set up two different periods for time record of every day in a week. Attention: The

period wouldnt take effect until the corresponding day is selected. For example: If you want to select Everyday, move the cursor to the

corresponding icon and press ENTER. (Play red hook means openOtherwise close)


60/141

59

4.4.4 Motion Detect (MD) Record

The way to enter the motion record interface: After login, through SETUPMotion continuous button operations to enter the motion record

interface, the interface is as follows(take the 16 channels machine for example):


61/141

60

Motion Alarm ScheduleYou can set different motion alarm periods for each channel. The everyday record period of a week can be set independently, and there are two

periods of every day. Focus on the On icon and press ENTER button; you can enter the schedule interface to set the periods for the corresponding

channel.

Motion record timeIt means the time period of recording, which is triggered by the motion alarm. The scope is 199 seconds.(Attention: Whether system would

stop recording or not based on the last motion detect alarm happened. For example: If the motion detect time is 5 seconds and the period is an hour,

the corresponding channel will be recording all the time as the motion interval is less than 5 seconds.)

Audio AlarmWhen you select this option, the audio device, which is connected to the machine, would ring when the system detects the motion.

Sensitivity (1~10)The sensitivity of the motion detection is adjustable (1~10), and it goes up in proper order from 1 to 10.

Motion areaEach channel has 560 motion detection areas in all (20 lines, 28 rows). Annotate: 4 channels machine has 140 motion detection areas in all (10


62/141

61

lines, 14 rows). Press ENTER key on the pink frame, and when the color of the f rame turns yellow, you can choose the detecting area throughUp

DownRightLeft keys, then press ENTER to make it available. Now, the chosen areas are transparent, and other areas are green. The green area

will glitter in red when video motion is detected. You can test the actual effect on the motion detect area interface. When the detection of a certain

area is open and there is motion in this area, the video of the area would turn red.

Sensor outputIt's used to set the linkage output of the motion alarm. (The 4 channels machine supports two-alarm outputs, and others support four alarm outputs.)

4.4.5 Alarm Record

The way to enter the alarm record interface: After login, through SETUPAlarmRec continuous button operations to enter the alarm record

interface, the interface is as follows (take 16 channels machine for example):


63/141

62

Each mode has its corresponding alarm inputs and outputs. The 4 channels supports four alarm inputs and two alarm outputs; the 8 channels

supports eight alarm inputs and four alarm outputs; the 16 channels supports nine alarm inputs and four alarm outputs. You can set the detecting

periodthe linkage record channelthe record time and the linkage alarm output of each alarm input according to your need.

Sensor Alarm ScheduleYou can set different sensor alarm periods for each channel. The everyday record period of a week can be set independently, and there are two


64/141

63

periods of every day. Focus on the On icon and press ENTER button; you can enter the schedule interface to set the periods for corresponding

channel.

Alarm Record TimeIt means the time period of recording, which is triggered by the sensor alarm. The scope is 199 seconds. (Attention: Whether system would

stop recording or not based on the last sensor alarm happened. For example: If the alarm record time is 5 seconds and the period is an hour, the

corresponding channel will be recording all the time as the alarm interval is less than 5 seconds. The record will continue forever if you don t reset

system after the sensor alarm has been triggered.)

Record channelIt means once the sensor has been triggered, the corresponding channel would begin to record. You can set one or several channels for a sensor.

Audio AlarmWhether output the alarm voice from the DVR audio output when there is a sensor alarm.

Sensor outIt's used to set the linkage output of a sensor. (4 channels supports two alarm outputs, others support four alarm outputs.)


65/141

64

4.5 Playback Operation

There are two ways of playback: (1) time retrieval playback; (2) file retrieval playback.

Several explanations: (1) the system can only playback one channel and it wont influence recording. (2) You can switch the record of different

channel by pressing corresponding digital key. ./: is used in 16 channels DVR as No.10. (3) When playback, you can press PIP keystroke torealize the picture in picture function. And the ./: keystroke is used to switch the two pictures.4.5.1 Playback by Time

The way to enter the Playback interface: After login, press PLAY key to enter the Playback interface. And the interface is as follows:


66/141

65

Input the channel number and the preliminary time that you want to retrieval, and then move the cursor on OK icon and press ENTER button,

system will automatically playback the record you set. If you dont know whether there are records during the period, you can focus the cursor on the

File info and press ENTER to check it in the File info interface.

4.5.2 Playback by File

The way to enter the File info interface: After login, through INFOFile info continuous button operations to enter the File info interface.

And the interface is as follows:


67/141

66

You can look for the record information such as when and how it recorded in the File info. For example: input 2006-4-12, channel 1 firstly,

then press the ENTER to refresh, then you can gain the corresponding information.

4.6 Backup Operation

There are two ways for backup: Backup the file to remote computer through network. Backup the file directly to the local hard disk. The


68/141

67

explanation of the last one would be shown as follows.

There are two kinds of disk for backup: the ordinary IDE hard disk and the SATA disk. System only supports a backup area; the surplus backup

areas are unavailable. If you use the IDE disk, be sure there is a partition for backup before you backup the file. If you use the SATA disk, you can

connect the disk directly to the machine by the SATA port which is on the front panel (without shutting off the machine). After the system prompts

you that the installation has already finished, you can backup the file to it. (Note: data in the backup area cant be backuped again)4.6.1 Data Backup

The way to enter the backup interface: After login, press the BACKUP key to enter the backup interface. And the interface is as follows:


69/141

68

One backup operation can backup the file of the channel and the period that you want to operate. Input the channel number and period, and then

focus on the Backup icon and press ENTER, system would automatically start to backup. (Annotate: the backup operation is available to therecord of 15 minutes before. For example: its 11:00 now, you can just backup the records before 10:45)

Date: Show the dates with backup files in current partition. Move the cursor on a certain date and press ENTER, the file list at the right side


70/141

69

would show you the file information of the date you chose.

Files: Show backup file information of a certain date.4.6.2 Playback the Data

If you want to playback the file that has been backuped, you have to enter the backup interface. Focus on the file that you want to operate and

press ENTER to playback the file.

4.7 PTZ and Channel Setting

PTZ and channel setting are placed in one interface, named the Channel interface. The way to enter the channel interface is as follows: After

login, through SETUP, Channel continuous button operations to enter the interface, and the interface is showed as following (take the 16

channels machine for example):


71/141

70

4.7.1 PTZ Setting

You have to correspond the PTZbaudrate and address of each channel with the PTZ before controlling. Method to set up: Place the cursor on

the choice frame or the input frame (the choice frame is for PTZ and baud rate, the input frame is for address). You can choose corresponding PTZ

and baud rate through -+ buttons. And set the address of the decoder by input digits.


72/141

71

The way to control the motor: Choose the camera to be controlled (single picture of the real-time videothe upper left corner one of the

multi-picture and the greater one of the picture in picture). Through the direction keys on the front panel, the keys for motor on the remote controller

or the customer end, you can control the motor.

Instruction of preset and call function: after focusing the PTZ on one position, press the preset keystroke on the remote controller, and there

will be a blue small square on the inferior right corner of the screen. Input a number, for example: 16. Then, move the PTZ by direction keys. Press

the call button on the remote controller, there will be a blue square on the inferior right corner of the screen, the PTZ will back to the preset position

after inputting 16.

4.7.2 Channel Setting

The channel setting is used to modify the channel parameters, such as: channel captionvideo lost alarm and video mask.

(1) Caption Setting

You can input 8 Chinese characters or 16 English figures at most for each channel caption. The caption is superposed regularly on upper left corner of the video. You can use the PIP key of the remote controller or the front panel to switch over the Chinese and English input mode.


73/141

72

When you input Chinese,you have to refer to the area-location code table(2) Video Lost Alarm Setting

When the Video Lost alarm corresponding with the channel is turned on (Play the red hook), once the video lost takes place, the machine will

warn (The sound for warning would last about 3 minutes). You can press the information key to see concrete warning contents.

(3) Video Mask Setting

Full mask for real-time videoWhen the state of this option is open (play ), the whole real-time video of the channel will be shielded, but it wouldnt influence the record and

the playback.

4.8 System Parameter Setting

4.8.1 System Time

The way to enter the system time interface: After login, through SETUPSysTime continuous button operation to enter the system time

interface, the interface is as follows:


74/141

73

This function is used to set or modify current system time. After finishing setting, system will reboot automatically. (Attention: Because system

time is in close relation with video record, try not to adjust system time on general occasion.)

4.8.2 System Password

The way to enter the power password interface: After login, through SETUPSysCodePower password continuous button operations to

enter the power password interface, the interface is as follows:


75/141

74

There are two passwords in the power password interface. Be sure that you press the ENTER button when focusing on the Save...icon after

modifying the password. The explanation is as follows:

1. Power password (Default value: 000000)Be used to verify the password when you startshut off the system.

2. Update password (Default value: 666666)Be used to verify the password when you update the system software.


76/141

75

Password restoration

Before saying the operation of restoring the password, there is another password should be mentionedadmin password (namely admin users'

password, default value: 12345678)The password restoration will restore three passwords: the power password, the update password, the admin

password and the keylock and its DN.

When you have forgotten system password or admin password or you cant unchain the keylock, you can comply with the following steps to

resume the default password.

Shut off the machine, and cut off the power supply.

1. Unload the cover screw, and remove the case lid from the machine.2. Find J4 (labels Password clear or Password reset) next to the SCM of the front panel.3. With jumping thread piece to put the legs 12 (next to the resistance R5) of J4 to the state of short circuit.4. Connect the power supply, and start machine.5. You can hear buzzers brief sound from the front panel; it indicates that the passwords have been set to the default value at the moment.6. Shut off the machine again, and cut off the machine power supply.7. Let the jumper to its old position.


77/141

76

8. Replace the case lid.4.8.3 Default Setting

The way to restore default setting: After login, through SETUPDefault continuous button operations to enter the interface whether to

restore system default setting. The interface is as follows:

System will prompt user whether to restore to default setting. Focus on the OK icon and press the ENTER button, then all the system

parameters would be set to default state.


78/141

77

Attention 1: After restoring default setting, all the record ways will be closed.

Attention 2: System languageColor SystemChannel captionSystem codeSystem timeUser account and Hard disk management wouldnt be

influenced.

The state of system default setting is as follows:

Record parameters: Over Write mode (Auto)

Date superposes (open)

Time superposes (open)

Image Poll (open) Polling intervals: 15 sec

Resolution (CIF)

Quality (3)

Frame rate 25 (the NTSC is 30)

Audio (open)

Time recordClose

Motion Detect recordClose


79/141

78

Alarm recordClose

ChannelPTZ (unknown)

Video Lost Alarm (close)

Video Mask (close)

Baudrate (default)

Address (corresponding with the channel number)

Video parameter: Brightness (64)

Contrast (64)

Saturation (64)

Hue (0)

4.9 Information

The information for inquiring is: alarm information, system information, hard disk information, file information, system status and system

logbook. About the file information, please refer to the File retrieval playback.


80/141

79

4.9.1 Current Alarm Information

Alarm information takes place as the present system warns. When the alarm is raised, you can look over the alarm information by pressing

INFO key to look over present alarm information. The alarm status interface is shown as follows:

It shows the warning information of three kinds of warning types on each channel: Sensor Alarm, Motion Alarm and Video Lost Alarm. You can

clear the alarm through the CLEAR button of the remote controller.


81/141

80

4.9.2 System Information

The way to enter the system information interface: After login, press INFO button to enter the system information interface, the interface is as

follows:

It displays software version, board sn, time, IP address, physical address of network card, the using partition and free space. And there are 4

submenus on the interface, such as: disk informationfile informationsystem status and logbook.


82/141

81

4.9.3 Disk Information

The way to enter the disk information interface: After login, through INFODisk info continuous keystroke operations to enter the disk

information interface, the interface is as follows:

It shows the detailed information of the hard disks that are connected to current system.

1.Disk list


83/141

82

It shows the partitions and the volume labels of the disks connected to current system.

2.Partition informationIt shows the detailed information of selected disk partition, including the following information:

IDE channelThere are 4 IDE channels at most (each channel can connect 2 IDE disks) , and a SATA port. Annotate: 4 channels DVR is 4 SATA ports (One port is

a special port for backup).

File systemThe system uses standard FAT32 file format.(It can be identified by PC directly)

Free spaceIt shows the free space of current partition.

Total spaceIt shows the total capacity of current partition.

3.Total disk information Total disk


84/141

83

Quantity of hard disks, which connect to the system, the upper limit is 8. (Annotate: 4 channels DVR can link 4 SATA disks at most.)

Total free spaceIt shows the free space of current system.

Total spaceIt shows the capacity of all disks connected to current system.

(Special explanation: the system only supports FAT32 file format.)

4.9.4 Recording Status

The way to enter the system status interface: After login, through INFOSys status continuous button operations to enter the system status

interface, the interface is as follows (take the 16 channels DVR for example):


85/141

84

It shows current record setting and current record status of the system.

Record settingIt shows the on/off status of each channels manual recordtime recordmotion record and alarm record.

Record statusIt shows the record status of each channels video type and quality, resolution and audio (on or off). If in the state of recording, the Type bar


86/141

85

would show the type of current record (There are 4 types: MN (manual)TM (timer)MT (motion)AM (alarm)). The position of audio: Gray means

off, and red means on.

4.9.5 System Logbook

The way to enter the system logbook interface: After login, through INFOLogbook continuous button operations to enter the logbook

interface, the interface is as follows:


87/141

86

Input the date you want to inquire at the button of the interface, press ENTER, and the system will show you the operation list of the date you

input. Move the cursor on the concrete log, the amplificatory log will be shown on top of the log frame. (Attention: The figure next to the Logbook

means the quantity of all logs on the daySystem can store 512 logs for a day at mostThe log file can't be discerned on PC)

The logbook includes some information as follow: system start-up and change version logalarm logcontrol PTZ loguser login log and log of

changing system parametersplayback log and backup log.


88/141


89/141

88

disk: data partition (DATA) or backup partition (BACKUP).

Format: Focus on the partition icon and press OK, system will prompt you whether to format the hard disk. You can set the type of the hard

disk(DATA or BACK) through -+before formatting. Data in the hard disk will be deleted completely after 4 seconds.

Attention: System supports only one partition for backup. The surplus ones would be useless (cant be used as backup partition or data partition).

If the hard disk has been partitioned before connecting to the DVR, the operation that formats any partition of the disk will format the disk to one

partition; the capability of hard disk that would be used on the DVR is 40G at least.

4.11 Network Setting


90/141

89

4.11.1 Simple Network Setting

The way to enter the Network interface: After login, through SETUPNetwork continuous button operations to enter the Network

interface. And the interface is as follows:

It is used to set the network parameters of system. With this function, you can visit the machine through network.

User name


91/141

90

Its used to identify the backup resource in backup partition. You can inquire the backup file according to the host name after you connect the

disk to PC.

Auto configIf the server in the LAN where the machine located has the DHCP service and you can select theAuto config option to gain the IP from server

automatically. You can only edit the standby config option at the time. The Standby config option would take effect while the auto config cut no

ice.

Use these configIf there is no DHCP service in the LAN, you can choose this option to designate the static IP address.

Command port and HTTP portThe numbers of ports can be modified by Page UpPage Down keystroke or data keys. The command port is the TCP monitor of all

communication ports of DVR. The HTTP monitor is used as IE browsing port. (Annotate: The setting of mapping refers to 4.12.2)

WAN enhanceWhen you want to visit the machine through WAN or Router, you should select this option.

Keylock


92/141

91

This function refers to 4.1.1

Use RS485 deviceThe function should be open when connects to the serial keyboard. The address code can be modified by Page UpPage Up key or data keys;

If you want to control a camera or PTZ coder through several pieces of DVR, all pieces of dvr must open the Use RS485 device option.

4.11.2 WAN Setting

1. Internet config


93/141

92

Its a kind of connection to the WAN. You can connect the WAN directly through dialing adsl at this interface.

User nameADSL account. PasswordADSL password. ConnectAfter you input the correct ADSL account and password, focus the cursor on the Connect icon and press ENTER to connect theWAN.


94/141

93

Auto connectIf you select this option, system will automatically connect the WAN after disconnection. Save the passwordIf you select this option, system will automatically save the ADSL password. The frameIt shows the network information of the pubic network after the connection has finished.2. Dynamic domain name server

It is the function that you can access the machine by domain name through Internet.It can parse the address that dial directly to internet or be


95/141

94

mapped to internet. After you have connected the machine to internet, input user namepassword and domain name ,and then focus on Login and

press ENTER to parse the domain name. (Annotate: The user name and password here refer to the peanut passport name and password that apply in

peanut shell websites). After parsing the domain name successfully, IP address will show the address with which the machine connects to

internet.Then you can access the machine with inputting the domain name directly in IE address or IP address of Client manager.You can go the

website www.oray.net to download the software of peanut with which you can apply the free domain name.

4.12 IE Operation Instructions

Notice: Set the safe rank of firewall to low or middle.

Forbid or unload the software such as network assistant, otherwise the software cant run.

Please make sure that the PC has installed DirectX 9.0 of Microsoft.and the Internet Explorer edition is 6.0 or above.

4.12.1 LAN operation Instructions

Set the parameters according to the following steps:

u Step1: Right click the IE icon on the desktop and choose the property on the pop-up menu.Select the Security bookmark and choose the
http://www.oray.net/http://www.oray.net/


96/141

95

Internet option. Click the Custom level icon, enable all the options concerned wih ActiveX and set the Reset to to medium-low on the Security

Setting window. The pictures are as follows:

u Step2: Do the same set to the Local internet option as the step1. The pictures are as follows:


97/141

96

u Step3: Ping the DVRs IP to make sure that the connection is ok.


98/141

97

u Step4: Input the IP to the address of IE and press Enter to connect.Input the user name and password of DVR to login, and there will be aprompt with login ok after the connection has succeeded. The picture is as follows:


99/141

98

u Step5: Right click the window and choose the channel you want to open.


100/141

99

If you want to close an image, you can right click the image and choose the close. If you want to maximize an image, just double click the image. If you want to control the PTZ, choose an image that can control PTZ and click the controlling keys (The condition that you control the PTZ is


101/141

100

that the PTZ, the baudrate and the address has been set correctly on DVR.)

It is a sample that the image has been opened:


102/141

101

If you want to playback, you can enter VOD interface by clicking the VOD button. As the picture shows down, input the same user name andpassword as step 4, then you can see the records that have been required. Double click the file to playback the corresponding record, and there are

some playing keys at the botton of the image.


103/141

102

4.12.2 WAN operation Instructions

WAN service setting

If you have regular WAN IP address, you can link DVR directly to WAN. Then you can visit the machine normally after setting IP, subnet maskand default gateway and enable the option WAN enhance.

Otherwise, you have to dial ADSL to connect to WAN.And the concret operation refers to 4.11.2.If you want several pieces of DVR connect to WAN with a wideband line, you can refer to the following steps:

At first, set up the IPsubnet maskdefault gateway and enable the option WAN enhance on the machine. Notice: the default gateway should be the

same with the gateway of the network sever which is for mapping. After setting, connect the DVR to LAN.Then you can use two methods to map to

WAN: Acarry on the mapping on the network server which connects to WAN directlyBcarry on the mapping through the router. (Attention: the

mapping instruction is only for TCP protocols).

A: Mapping through the network server

Take the situation that the servers OS is Windows XP and dials ADSL for example:


104/141

103

The interface of network setting is as follows:

Attention: The default command port and http port are 8101 and 80. You can set the values according to your needs, when you have set the them and

save the change, system will reboot to make the change be effectual.

A1Right click the My Network Places icon on the desktop and select the Properties.


105/141

104

A2Right click the ADSL icon and select the Properties.


106/141

105

A3Click the Advanced bookmark and enable the option Allow other network users to connect through this computers internet

connection ,the click the Settings button to enter the Advanced settings.


107/141

106

A4Click the Add button to enter the Service settings.


108/141

107

A5Add the following information separately in Service settings: You can input the Description of service according to your need. The address


109/141

108

is IP address of DVR that you want to map, for example: 192. 168. 0. 6. And you should add the ports which are same as the command port and http

port to the IP. (Attention: there must be no conflict to ports.) We illustrate the default ports and custom ports for mapping, and the pictures are shown

as follows.Picture 1 and 2 are for the default pots, and the picture 3 and 4 are for the custom ports.

Picture 1 picture 2


110/141

109

Picture 3 picture 4

A6After the network server dials ADSL successfully, run the cmd to enter DOS. Then run ipconfig /all to look over the internet IP and write

down the IP for interviewing.


111/141

110

A7Now we can use any computer that can get on internet to interview the mapped DVR.

1. Access the DVR with default ports: a, To DVR client manager: you only need to input the internet IP on the IP address and correct username andpassword and login to connect the DVR; b, To IE, you input the internet IP on IP address to download the ActiveX, when you have downloaded


112/141

111

successfully, input the correct usename and password to login and open the images.

2. Access the DVR with custom ports: a, To DVR client manager: you need to input the internet IP with the command port on the IP address (e.g.219.134.28.150:6666) and correct username and password and login to connect the DVR; b, To IE, you input the internet IP with http port on IP

address (e.g. http://219.134.28.150:66) to download the ActiveX, when you have downloaded successfully, input the correct usename with command

port (e.g. admin:6666) and password to login and open the images.

Attention: the symbol : between IP address and port or user name and port should be input in English type.

BMapping through the router

Network interface is as following picture:
http://219.134.28.150:66/http://219.134.28.150:66/


113/141

112

Attention: The default command port and http port are 8101 and 80. You can set the values according to your needs, when you have set the them and

save the change, system will reboot to make the change be effectual.

You can look over the instruction of router for the detailed steps of mapping.

4.13 Software update


114/141

113

Instructions before update: please read it carefully.

Please confirm the edition of the present software, preventing having no method to degrade when update fails. We dont suggest you update if youdont need the new function or dont have any other questions. Please store the important record before updating.

You must guarantee the stability of power and network, or the update process will be failing. If there is no prompt after 6 miutes since you clickthe download, you have to cut off the power and then electrify. When the system starts successfully, please check whether the update succeeds.

Before update, you must confirm the file for update, whether the file is fit for the DVR.Otherwise, the update will fail. Worsely, DVR can

t start

normally. (In this situation, you have to send the machine to us for maintenance)

Please access our website to download the instructions of new functions after updating.Do not rename all the files we supply, specially the flash. Otherwise, we wont offer free service for all the concerned problems.The DVR updater will be installed automatically when you install the DVR client manager. (The program is in the CD that comes along with theDVR)

The concrete operations are as follows:

1. Connect the machine with PC through coherent network line or LAN. (Pay attention to preventing IP conflict)

2. You should shut off the machine through front panel or remote controller at first. (Make sure you know the IP of DVR before shutting off).


115/141

114

3. The state of update: a. the front panel with VFD: press the power, input the update password (default: 666666) and press the enter, meanwhile,

the VFD would display UPDATE, you can now update the machine from PC; b. the front panel without VFD: press the power until you hear a

beep, input the password (default: 666666) and press the enter, meanwhile, the indicator light for update would be on, you can now update the

machine from PC.

4. Run the DVR updater on PC, and choose the file to be updated.


116/141

115

5. Input the IP of the machine you want to update and clickping button to make sure that the join succeed.

6. Click the button download, and the update begins.

7. It probably takes 3 minutes to update.

8. When a window that contains the information of updating successfully pops up, it means that the update has ended.

9. Then the machine would restart automatically.

10. After updating, the admin password, the power password, the update password would change to default.

PS: the default password-admin:12345678, power password:000000,update password: 666666.

4.14 Cut Out to Resume

If the power cuts off unexpectedly when the system is at the state of standing by or running, system would start automatically and return to the

state before cutting out after the power returns.Its function is to maintain the continuity of system work when the power supply is out of the way.


117/141

116

Appendix 1: FAQ & Answers for DVR

Thank you for choosing our products. We will always be at your services. In case you have any difficultieson using the products, please refer to

the below frequently questions & answers. If you cannot find solution here, or the solution offered here still fails, please feel free to contact us by our

hotline or technical support E-mail box. We will make most timely reply to your questions.

Detect method in common use:

1Replacing Replace the power of DVR or the hard disk

2The least loadingTake off the hard diskI/O of video/audio/alarm

3UpdatingSolve the no compatibility between the DVR and external equipments

Attention: some problems maybe take place on improper operations, when you are uncertain about this, please set the paramet

User Manual for V3_0_SDVR

Documents

Transcript of User Manual for V3_0_SDVR