User Guide LuxHome User Wireless System Guide System 2 - User Guide.pdf · 12. Alarm Installation...

LuxHome Wireless Alarm System

User Guide

User Guide

21st Century Alarms & CCTV Solutions 2017 Contents: Page

01. Using the Control Panel Keypad…………………………….. 01 02. Using the Remote Control……………………………………… 02 03. Using the Remote Keypad……………………………………… 02 04. Auto Dialler Call Acknowledgement………………………. 03 05. Changing The User Code………………………………………… 03 06. LED Meanings………………………………………………………… 04 07. Low Battery…………………………………………………………….04 08. Changing Batteries………………………………………………….05 09. Testing the Alarm System………………………………………. 06 10. Removing Detectors for Decorating………………………. 07 11. Trouble Shooting…………………………………………………….08 12. Alarm Installation Details………………………………………. 09

LuxHome Wireless Alarm System – User Guide

21st Century Alarm & CCTV Solutions

www.21stcenturyalarms.co.uk

Page | 1

01. Using the Control Panel Keypad Key:

Full Arm (all detectors) –Day Mode or (Away)

Part Arm (selected detector disabled) – Night Mode or (Home)

Disarm (system off)

During the Arming Sequence, the alarm will emit a Beeping Tone that gets faster towards the end of the sequence, and a flashing LED will highlight the ARM mode used. Arming – Flashing or Blinking Armed - Solid

Flashing LED System Arming in Full Arm

Flashing LED System Arming in Part Arm

Solid LED System Armed in Full Arm

Solid LED System Armed in Part Arm

Full Arm Part Arm Disarm

Enter Escape (Quit Menu)

Programming (Engineer Mode)

Panic (press for 5 Sec)




Page | 2

02. Using the Remote Control

Side Button – Slide up to activate “PANIC”

Press Disarm from outside your property, the Bell Box will Strobe Twice with Two beeps to signify “Disarmed” 03. Using the Remote Keypad

Full Arm

Part Arm

Disarm Panic

Key:

Full Arm Part Arm Not used Disarm (Except for Panic)

The “LOW BATTERY” indicator on the front of the Keypad will not flash until the Keypad is used for ARM/DISARM or Panic, (Battery Saving Feature).




Page | 3

04. Auto Dialler Call Acknowledgement Once the Call from the Alarm’s Auto Dialler has been received:

During or after the message is played, Press “*” on your phones keypad to acknowledge the call and stop the Auto Dialler dialling numbers 2 and 3. The Auto-dialler with respond with a Tone and then hang up. Reset Alarm Following Activation Following an Activation of the Alarm, Disarm as normal, the control Panel will display the Zone that has been triggered. (Flashing LED over the Zone Number). Press:

To reset Alarm and Clear Display (display reverts to normal after 5 minutes)

05. Changing the User Code 1. Enter Programming mode, as detailed below.

The Arm and Part-Arm LEDs will illuminate and all Zone, Fire and tamper LEDs will flash. The system is now in Programme Mode. 2. Zone LEDs 1-4 will illuminate. 3. Enter a new 4 digit User Access code. As each digit is entered an illuminated zone LED

will be turned OFF.

4.




Page | 4

06. LED Meanings Solid LED

Solid LED : Power OK Flashing LED : Mains or Panel Battery Failure

Solid LED System in Part Arm

Solid LED System in Full Arm

Solid LED /Flashing LED Low Battery

Flashing LED Meanings

LED over Zone Alarm was triggered by detector on Zone 1-6 Fire Panic Button on Remote was used Tamper Control Panel/PIR/Door Contact/Bell Box has been Tampered with or Opened. All LEDS Flashing Panic Button on Control Panel was used

07. Low Battery Once Low Battery is indicated, alarm works as normal, change battery’s with 2 weeks. Solid LED: check your Door/Window Contacts for low battery indication (RED LED) Door/Window Contact

Normal Mode, No LED Indication (Battery OK) Low Battery, Flashing LED on Open/Close.

Flashing LED: Check your PIR’s for low battery indication (RED Flashing LED) Passive Infra-RED

Normal Mode, No LED Indication (Battery OK) Low Battery, Flashing LED when movement detected.




Page | 5

Low Battery Indication (RED LED)

08. Changing Batteries 1, Put the Alarm in Test Mode, this will disable the Tamper Activation of the System. With the system in Standby Mode with the Power LED ON, press:

2, Change the Detector Battery(s), when finished Press to leave Test mode and return to Standby. Remote Control When the Remote Control is operated under low battery conditions the transmit LED will continue to flash after the button has been released.

Under normal battery conditions the LED will extinguish when the button is released.

Remote Keypad

1. Enter the user code “Twice” will flash for 20 seconds and disable Tamper activation.

2. Undo the fixing screw at bottom of Keypad and remove from the wall mounting plate.

3. Undo the two fixing screws in the rear cover and remove the battery cover.

4. Replace battery with a new 9V PP3 Alkaline battery 5. Replace and fix the rear battery cover and then refit and secure the

Keypad onto the wall plate.

1 x 9V PP3 Alkaline Battery

1 x 3V CR2032 Lithium Battery

Disarm Enter




Page | 6

09. Testing the Alarm System Put the Alarm in Test Mode, With the system in Standby Mode with the Power LED ON, press:

The Arm and Part-Arm LEDs will flash; the system is now in Test Mode Detector Test Before commencing testing please ensure that there is no movement in any PIR protected area for at least 2minutes, all doors/windows protected by Magnetic Contact Detectors are closed and that all battery covers are correctly fitted. Press and Zone LED 1 will illuminate. Trigger each Detector on the system by either walking into a PIR Detector protected area or by opening a door/ window protected by a Magnetic Contact Detector. As each Detector is triggered the Control Panel will beep and the LED of the zone which the Detector is set for will be illuminated. Press to exit Detector Test Solar Siren Test Press Zone LED 3 will be illuminated during the test. The Control Panel alarm and the External Solar Siren will be operated for a period of approximately 5 seconds with the external Solar Siren switching ON and OFF a few seconds after the Control Panel. Voice Dialler Test Press Zone LED 6 will illuminate The voice dialler will call each active number in the dialling sequence in turn. When a call is answered the pre-recorded alarm message will be replayed. If the call is unanswered or an acknowledgement signal is not received from the number called, (i.e. by pressing the * button on the telephone keypad) the next number in the sequence will be called. Press to leave Voice Dialler Test. Press to leave Test mode and return to Standby.

Disarm Enter




Page | 7

10. Removing Detectors for Decorating The LuxHome Wireless Alarm System is Fully Tampered and will activate the Alarm if tampered with, if you wish to remove a Detector or the Control Panel for Decorating the Alarm System will need to be placed in “Test Mode” to disable “Tamper” Method Passive Infra-Red (PIR) 1. To disable “Tamper” you will need to put the system in “Test Mode” 2. With the system in Standby Mode with the Power LED ON, press:

The Arm and Part-Arm LEDs will flash; the system is now in “Test Mode”

3. Removing a PIR, carefully undo the screw at the bottom of the PIR and put somewhere safe, remove the cover, the PIR will be mounted by 1 or 2 screws, unscrew and remove the base.

4. To Replace the PIR base, find to original wall plug(s) and replace the screw(s), making sure not to over tighten as this may cause the PIR Housing to warp.

5. Replace PIR cover making sure to align the top of both the PIR and Base, and clip together, this must be tight connection, if misaligned or not tight “Tamper” will remain open.

6. Replace the bottom screw at the bottom of the PIR. 7. When finished: Press to leave Test mode and return to Standby. Door/Window Contact It you need to remove a Door or Window Contact, follow Steps 1 and 2 as above. The Contact Transmitter (long part with Battery) will be Super Glued in Place, to remove you will need a Razor Blade or Stanley Knife. Carefully insert the Blade under the Contact and pry free and put somewhere safe. The Contact (small white magnet) will be held in place by a Sticky pad or Super Glue, follow the same method as for The Contact Transmitter, and keep with the Contact Transmitter and Contact together.

When Replacing the Door/Window Contact, fit the magnet on the Moving Part of the Door and Transmitter on to the frame, use Super Glue or Sticky Pads, the gap between the magnet and Transmitter must be no more than 10mm and the arrow on the Magnet is aligned with the (-) mark on the Tranmitter, the front cover on the Contact needs to be aligned and closed tight to avoid “Tamper” activations, follow step 7 as above to leave

Test mode and return to Standby. It is not recommended that the Control Panel, or Bell Box be removed by the user as these items contain High Voltage, please contact 21st Century Alarms for further information.

Disarm Enter




Page | 8

11. Trouble Shooting

Red LED on PIR/Contact is not working. o The Red LED is turned off on purpose, to save battery life, and is

only visible when the Battery in the detector is getting low and needs replacing.

Solar Bell Box making a “Clicking Sound”. o Rechargeable Battery in Bell Box needs replacing.

Power LED is Flashing. o Check Power Supply is plugged into 3pin socket and that the

socket is switched on. or

o Check that the Power Supply is warm to the touch, if it is cold to the touch the Power Supply may need replacing.

Tamper LED is illuminated. o Check all PIR cases are properly aligned, and clipped together. o Check all Door/Window Contact battery compartments are

properly aligned, and clipped together. When the Arm/Disarm button is pressed on the Remote Control, the

Alarm System keeps Beeping or Going in Panic. o Make sure the rubber buttons are seated correctly and not getting

jammed against the remote control case. o Remove the screw securing the remote control, and carefully

separate the case, remove the rubber buttons and straighten/flatten, replace the rubber buttons into the remote control front and firmly push in to place, reassemble remote control and test.

The Auto Dialler is not contacting numbers following activation. o Check that the Telephone connector from the Control Panel is

plugged into a working telephone. o Plug a Standard Telephone into the phone socket and check for a

dial tone. o If a dial tone has been detected, replace the Alarm Telephone

connector into the socket and test (see Voice Dialler Test under Testing the System)




Page | 9

12. Alarm Installation Details Date of Installation: Installer: ALARM PLAN Zone Area Type Detector

01 02 03 04 05 06

CALL OUT/SERVICE HISTORY Date Call Out/Service Information ENGINEER

User Guide LuxHome User Wireless System Guide System 2 - User Guide.pdf · 12. Alarm Installation...

Documents

Transcript of User Guide LuxHome User Wireless System Guide System 2 - User Guide.pdf · 12. Alarm Installation...