Use this if your Router or Access Point(AP) supports WPS 1...

Immediately push the button on your Range Extender.

1 221Plug your Range Extender into a power outlet near your Router/AP.

LED Explanation

Quick Setup using the WPS Button

RE200

Applicable Model:

Method TWO: Setup using your Web Browser

WPS Method ONE: Quick Setup using the WPS Button

Push the WPS button on your Router/AP.

If the WPS connection fails, please go to Method TWO.

Wait until the ‘ ’ and ‘ ’ LEDs light up.

Method ONE

Quick Installation Guide

Use this if your Router or Access Point(AP) supports WPS

Frequently Asked Questions (FAQ)

A1: While the Range Extender is plugged into a power outlet, press the RESET button with a pen for 1 second. Wait 2 seconds until all the LEDs flash once.ORA2: Use your web browser to log into the management page, go to “System Tools -> Factory Defaults” and click “Restore”. Wait 5 seconds until all the LEDs flash once.

Q1. How to reset the Range Extender?A: First, make sure your computer is connected to the extender network and disconnected from any other network. Second, make sure your computer is set to “Obtain an IP address automatically”.

RESET

The Range Extender shares the same Wi-Fi Network Name (SSID) and Wi-Fi Password with your main Router/AP.

Password (ABCDEF)SSID (TP-LINK_XXGHz_XXX)


Q2. I typed http://tplinkextender.net in the browser URL bar, why can't I see the quick setup page?

A: Please visit “www.tp-link.com”, find “Support>Contact Technical Support>Hotline Support” for more information.

Q3. What’s the technical support hotline?

RESET

ETHERNET

Power on Push the two WPS buttons

Enjoy!

7106

5047

39

REV

1.0.

0

3

Keep the Range Extender away from devices like cordless phones, Bluetooth devices and Microwave Ovens to minimize wireless interference.

If possible, try to place your extender in open corridors or spacious locations rather than a crowded room.

far away

After you have configured your Range Extender, move it to a location for the best signal quality and coverage in your house. The Range Extender will automatically reconnect to your main Router/AP within about 30 seconds after you plug it into another power outlet. * Keep the following in mind:

Relocate

The ‘ ’ LED should go from flashing to solid, showing that WPS connection has succeeded, then it will turn off in 2 minutes.

The ideal location for your Range Extender is Halfway between your main Router/AP and Wi-Fi-enabled devices.

If possible, try to place your Range Extender in a location where the 2.4G/5G LEDs are Green.

5G/2.4GSolid Green: The Range Extender is connected to the 5G/2.4G wireless network of your main Router/AP, and the signal strength is strong.Solid Red: The Range Extender is connected to the 5G/2.4G wireless network of your main Router/AP, but the signal strength is weak.Off: The Range Extender isn’t connected to your main Router/AP.

On: The Range Extender’s wireless function is enabled.Off: The Range Extender’s wireless function is disabled.

(Wireless Signal)

(ETHERNET)On: A device is connected to the ETHERNET port, but there is no activity.Flashing: A device is connected to the ETHERNET port, and is active.Off: No device is connected to the ETHERNET port.

(Power)On: The Range Extender is on.Off: The Range Extender is off.

On: The Range Extender has established a secure connection. Flashing: The Range Extender is establishing a secure connection.Off: No active connection.

(RE)

2. Click the Refresh icon and connect to the Range Extender (the default wireless network name is: TP-LINK_Extender_XXGHz as listed on the rear panel) and go to Step 3.

Enjoy!Password (ABCDEF)

SSID (TP-LINK_XXGHz_XXX/TP-LINK_XXGHz_XXX_EXT)

Refer to Step 3 of Method ONE on the other side.

Relocate

3

4

Connecting via Wireless

Connection are available

Not connected

Wireless Network Connetion

Connect automatically Connect

TP-LINK_Extender_XXGHz

1. Disconnect your Ethernet Connection. Click the Wireless Network Connection icon on your desktop.

or

2Connecting via Ethernet Cable

1. Disconnect your computer from all wireless networks.

2. Connect the Range Extender to your computer via an Ethernet cable. Then go to Step 3.

Entertainment Adapter WirelessConnectionConnectionEthernet

Smart TV Game Console Desktop Laptop Smartphone Tablet

Setup using your Web BrowserMethod TWO

1Plug your Range Extender into a power outlet near your Router/AP.

Connect your computer to the Range ExtenderPower on

√


The Range Extender's single ETHERNET port allows the Range Extender to function as a wireless adapter connecting a wired device like Blu-ray players, game consoles, DVRs and smart TVs. At the same time, the device can share the wireless network. Please follow Method ONE or Method TWO to set up the Range Extender first and then refer to this connection diagram to connect it to one Ethernet-enabled device.

Wait until the ‘ ’ and ‘ ’ LEDs light up.

http://tplinkextender.net

admin

admin

OK Cancel

Type “http://tplinkextender.net” in your Web browser and press Enter. Log in to the management page using user name “admin” and password “admin”.

It may take 5 seconds or more for the login page to pop up.If it does not pop up, refresh the browser, otherwise, please refer to the FAQ > Q2.

Configure1 2

Please click Next to set up the Range Extender or click Exit to go to the Device Management Page.

Main Router/AP WiFi Network Name(SSID):

a. The Quick Setup page appears when you login in.

Below are the major setup process steps.

Exit Next

Wi-Fi Network Name_2.4GHz:

Wi-Fi Network Name_5GHz:

Connection Status:

N/A

N/A

Disconnected

f. The 2.4G/5G LEDs will light up if the configuration is successful.c. Fill in the Wi-Fi Password of your main Router/AP. You can copy the Wi-Fi Network Name (SSID) from your main Router/AP (TP-LINK_2.4GHz_XXX) or set a new one (TP-LINK_2.4GHz_XXX_EXT).

TP-LINK_2.4GHz_XXX

00-0A-EB-74-06-06

Most Secure(WPA-PSK/WPA2-PSK)

123456789

Copy from Main Router/AP TP-LINK_2.4GHz_XXX

Customize

Main Router/AP Network (2.4GHz)


Main Router/AP MAC Address(BSSID):

WiFi Security Option:

Fill in the WiFi Password of your Main Router/AP:

Range Extender Network (2.4GHz)

Range Extender WiFi Network Name(SSID):

Back Next

TP-LINK_2.4GHz_XXX_EXT

Choose Region Wireless Settings Review SettingsStart

Back Next


e. Fill in the Wi-Fi Password of your main Router/AP. You can copy the Wi-Fi Network Name (SSID) from your main Router/AP (TP-LINK_5GHz_XXX) or set a new one (TP-LINK_5GHz_XXX_EXT).


Signal MAC Channel Security

00-0A-EB-74-06-06 1 WPA-PSK

0C-72-2C-B3-A5-2C 1 WPA-PSK

Available Wireless Networks (2.4GHz): 24

Choose SSID

TP-LINK_2.4GHz_XXX

TP-LINK_XXX

Back Rescan Next

b. Select your Router/AP’s 2.4GHz Wireless Network, for example, TP-LINK_2.4GHz_XXX.

√


d. Select your Router/AP’s 5GHz Wireless Network, for example, TP-LINK_5GHz_XXX.

Signal MAC Channel Security

00-0A-EB-74-06-07 1 WPA-PSK

0C-36-2C-B3-A4-2D 1 WPA-PSK

Available Wireless Networks (5GHz): 5

Choose SSID

TP-LINK_5GHz_XXX

TP-LINK_XXX

Back Rescan Next

√


Configuration Completed Successfully.

Completed!

100%

Please wait a moment, if the browser does not refresh automatically, click Refresh on the top of your

browser.

Restart

TP-LINK_5GHz_XXX

00-0A-EB-74-06-07

Most Secure(WPA-PSK/WPA2-PSK)

123456789

Copy from Main Router/AP TP-LINK_5GHz_XXX

Customize

Main Router/AP Network (5GHz)


Main Router/AP MAC Address(BSSID):

WiFi Security Option:

Fill in the WiFi Password of your Main Router/AP:

Range Extender Network (5GHz)

Range Extender WiFi Network Name(SSID):

TP-LINK_5GHz_XXX_EXT

Choose the Range Extender’s Wi-Fi Network Name (TP-LINK_XXGHz_XXX or TP-LINK_XXGHz_XXX_EXT). The Range Extender shares your main Router/AP’s Wi-Fi Password.

7106504739_RE200(EU)_QIG_V1_A7106504739_RE200(EU)_QIG_V1_B

Use this if your Router or Access Point(AP) supports WPS 1...

Documents

Transcript of Use this if your Router or Access Point(AP) supports WPS 1...