US HORIZON MESSINA SERIES - C.R. Laurence Co.,...
Transcript of US HORIZON MESSINA SERIES - C.R. Laurence Co.,...
INSTALLATION INSTRUCTIONS
US HORIZONMESSINA SERIES
HEADERLESS SHOWER DOOR
28539 Industry Drive, Valencia, CA 91355Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567Phone: (661) 775-1675 Fax: (661) 775-1676ushorizon.com
USHORIZON®
11M0341H
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 2
MES1 MES3
64” (1626 mm) Rounded Style Essence Kit with Header 64” (1626 mm) Squared Style Essence Kit with Header
BR4_ SR4_ TG4_ ESSF1S*
Rounded Style Rollers (2) Squared Style Rollers (2) Top Guide Bumpers (2)
AUHP12_ SDCEC12_ SVE301_ PWJP95
95” (2413 mm) U-Channel End Cap for U-Channel64” (1626 mm) Bottom Track
with Mounting Strip 95” (2413 mm) Plastic L-Seal
ESSLSS* SB596
Spanner Wrench for Roller Adjustment 1/16” Setting Block (Use as Guide)
Kit Contains:1 Top Guide2 Rubber Bumpers1 64“ (1626 mm) Bottom Track with Mounting Channel and Fasteners1 95” (2413 mm) L-Seal1 95” (2413 mm) U-Channel1 End Cap for U-Channel2 Rounded Style Bottom Rollers1 Spanner Wrench
INTERIOR
NOTE: Glass Panels Not Included.
Kit Contains:1 Top Guide2 Rubber Bumpers1 64“ (1626 mm) Bottom Track with Mounting Channel and Fasteners1 95” (2413 mm) L-Seal1 95” (2413 mm) U-Channel1 End Cap for U-Channel2 Squared Style Bottom Rollers1 Spanner Wrench
INTERIOR
NOTE: Glass Panels Not Included.
PARTS LIST
* Available through Technical Sales at (661) 775-1675 NOTE: MES1 installation drawings shown in this manual. Other installations similar.
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 3
OPENING WIDTH
TRACK LENGTH
Allow 3/8”(10 mm)
Clearancefor Top Guide.
OV
ER
ALL
HE
IGH
T
Drawing not to scale. Shown from interior.
NOTE: For use with 1/2” (12 mm) Tempered Glass only. Do Not use Laminated Glass.
OV
ER
ALL
HE
IGH
T
3/8” (10 mm)
FIX
ED
PA
NE
L
SLI
DIN
G D
OO
R
EXTERIOR
Center Line1-19/32” (40 mm)
NOTE: Mounting Brackets for Fixed Panel Sold Separately.
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3GLASS FABRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4SITE PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MARK LOCATION FOR TRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5FRAME FABRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CUT BOTTOM TRACK AND U-CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5FRAME INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7
INSTALL MOUNTING STRIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6INSTALL BOTTOM TRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6INSTALL U-CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7INSTALL FIXED PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SLIDING DOOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8INSTALL TOP GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8INSTALL BOTTOM ROLLERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SLIDING DOOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9INSTALL SLIDING DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9INSTALL ANTI-LIFT GUIDES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FINISHING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10INSTALL L-SEAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10INSTALL BUMPERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SPECIFICATIONS
IMPORTANT: READ THIS MANUAL THOROUGHLY BEFORE BEGINNING INSTALLATION.
ORDER OF ASSEMBLY AND INSTALLATION
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 4
NOTE: Drawings not shown to scale. Track is cut 1/16” (2 mm) less than Opening Width and centered in opening. Overall Height is height from curb/floor to top of glass. Drawings shown from interior.
NOTE: For use with 1/2” (12 mm) Tempered Glass only. Do Not use Laminated Glass.
OPENING WIDTHTRACK LENGTHFixed Glass set
1/8” (3 mm) from wall.1/4” (6 mm) Gap
between Sliding Doorand wall for L-Seal.
3/16” (5 mm)Gap for U-Channeland Setting Block.
Glass to Wall Brackets(Not Included)
Install Rubber Bumpersto Wall Brackets at Wall.
Fixed Glassoverlaps
Sliding Door2-7/8” (73 mm)
Fixed Glass aligns withtop of Sliding Panel.
Allow 3/8” (10 mm)Clearance for Top Guide.
OV
ER
ALL
HE
IGH
T
FIXED PANEL
FIX
ED
PA
NE
L H
EIG
HT
FIXED PANEL WIDTH
Holes forMounting Fixtures
Holes forMounting Fixtures
NOTE: Refer to Mounting Fixture Fabrication Instructions for Hole Size and Locations.
4” (102 mm)4” (102 mm)7/16” (11 mm)
SLIDING DOOR GLASS
3” (76 mm)Diameter
2”(51 mm)
1/2” (13 mm)Diameter
5/8” (16 mm)
Position Holes for Door Pull with
Projection greater than 1/2” (13 mm).
1”(25 mm)
1-3/8”(34 mm)
3/8” (10 mm)
SLI
DIN
G D
OO
R H
EIG
HT
SLIDING DOOR WIDTH
FIXED PANEL WIDTH : Opening Width Divided by 2 minus 1/2” (13 mm)
SLIDING DOOR WIDTH : Opening Width Divided by 2 plus 3” (76 mm)
FIXED PANEL HEIGHT : Overall Height minus 3/16” (5 mm)
SLIDING DOOR HEIGHT : Overall Height minus 5/8” (16 mm)
GLASS FABRICATION
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 5
EXTERIOR
OV
ER
ALL
HE
IGH
T
Top of Guide3/8” (10 mm)
1-19/32”(40 mm)
CenterLine
Allow minimum1-19/32” (40 mm)from Center Line
to Edge. EXTERIOR
1
2
Cut Bottom Track and Mounting Strip from same end.
Cut U-Channel for Fixed Panel.
NOTE: The Bottom Track and Mounting Strip are fabricated with the same drainage system on both ends. Determine if the surface is out of level first and then cut excess from the same end of both profiles so the drains will align at the low side of the surface when installed.
EXTERIOR
Mounting Strip
Bottom Track
U-Channel
EXTERIOR
U-Channel
U-CHANNEL WIDTH = OPENING WIDTH
DIVIDED BY 2 MINUS 1/8” (3 MM)
2
EXTERIOR
OPENING WIDTH
Level LineLower End
Cut Excess from SameEnd of Both Profiles
so Drains Align.
1
1
EXTERIOR
MountingStrip
BottomTrack
B
A
TRACK WIDTH = OPENING WIDTH MINUS 1/16” (2 MM)
Ensure correct orientation of profiles before cutting.Position drains at Low End of Surface.
SITE PREPARATIONMark Location for Track
FRAME FABRICATIONCut Bottom Track and U-Channel
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 6
1/2”(13 mm)
2
2
Positiondrain at low end.
EXTERIOR
A1
1
Mount with #8 Flat Head Screws suitable for substrate.
Screws by others.
B
1 Install Mounting Channel.
Seal 1/2” (13 mm) at each end.
NOTE: Ensure Mounting Channel is set at correct orientation with drain at low end.
NOTE: Drill holes 6” (152 mm) from ends and 12” (305 mm) maximum in between.
Lower End
2 Silicone at Ends.
Install Bottom Track.3
B
A
3
EXTERIOR
Mounting Channel
Bottom TrackU-Channel
Allow 11/16” (17 mm) gap to mount U-Channel.
3 B
A3
Align Drains.
Fasten at all hole locations with included 8-32 x 5/16” Flat Head Phillips
Machine Screws.
1/2”(13 mm)
2
FRAME INSTALLATIONInstall Mounting Strip
Install Bottom Track
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 7
A
A
B
EXTERIOR
PlaceSetting Blocks
at quarter points.
2
NOTE: Use fasteners suitable for substrate. Space 6” (152 mm) from ends and 12” (305 mm) maximum in between.
NOTE: Place Setting Blocks in U-Channel at quarter points before setting glass. (Setting Blocks not included)
1 Attach End Cap to U-Channel and mount 1/8” (3 mm) from wall.
Attach Wall Mounts to Fixed Panel.
Install Fixed Glass Panel in U-Channel and secure to wall.
A1
AttachEnd Cap.
EXTERIOR
Bottom Track
U-Channel
Seal and tool between U-Channel and Bottom Track.
D1Secure withscrews by
others.
C1
1/8” (3 mm)Gap
Position withgap at wall.B1
3
3
EXTERIORA
3
B
CL90S_ Wall Mounts
(Not Included).
C
C
Follow Installation Instructions included with Wall Mounts. NOTE: Wall Mounts not included.
NOTE: CL90S_Wall Mounts
(Not Included).Shown as
example only.
3
See Page 11 to confirm center hole can be used to install Bumpers.
Secure Wall Mount to
wall at top and bottom holes.
C
EXTERIOR
FRAME INSTALLATION (CONTINUED)Install U-Channel
Install Fixed Panel
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 8
Align Bottom RollersFlush to Bottom Glass.
7
6
6
4
Top Guide Assembled
1
Guide Bodywith
PlasticBushings
ClampingPlate
SideGasket
1
2
3
Unpack Top Guide and remove Clamping Plate and Side Gasket. Fit Guide Body with Plastic Bushings into holes in glass.
Remove protective liner from Side Gaskets. Install on Roller Body and Clamping Plate.
Adjust wheel height and tighten.
NOTE: Loosen center bolt one full turn to adjust. Use included Spanner Head to rotate cam and raise wheel height +/- 1/8” (3 mm). Begin with wheel at minimum position. Tighten center bolt snugly to hold position.
Secure Clamping Plate with Side Gasket to Guide Body.
Fit Roller Body into hole in glass. Align Clamping Plate on other side and permently tighten.
Unpack Bottom Rollers and remove Clamping Plates.
4
6
5
7
Thick SideGaskets
Thin SideGaskets
Anti-Lift Guardwith Screws
SpannerHead
Bottom RollerAssembled
Top Guide
Bottom Rollers
INTERIORFACING UP
NOTE: Bottom Rollers packaged with two sets of side gaskets. Use the Thin Gaskets for 1/2” (12 mm) glass. Anti-Lift Guard is installed after door installation.
A5Loosen
Center Bolt
5Securely Tighten
Center Bolt
D
1/8”(3 mm)
MaximumHeight
MinimumHeight
Adjust to MinimumHeight.
5 C
5Use Included
Spanner Headto Turn Cam.
B
Spanner Driverby Others
2
3
SLIDING DOOR ASSEMBLYInstall Top Guide
Install Bottom Rollers
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 9
INTERIOR
NOTE: CL90S_Wall Mounts
(Not Included).Shown as
example only.
2
3
1
Test door and adjust as needed.
Lift Sliding Door over Fixed Panel. Align Top Guide and lower onto Bottom Track.
Install Anti-Lift Guards on Rollers.
3
PushAnti-Lift tight
and secure screws.
INTERIOR
CNOTE: The Anti-Lift Guard is installed with a 1/16” (1 mm) gap between the top of the guard and the bottom of the Bottom Track. Use included Setting Block as a guide for proper clearance.
RemoveSetting Block.
INTERIOR
3 D
B3
Attach withincluded Screws.
INTERIOR
3 A
Place included Setting Block on Anti-Lift as a guide.
SettingBlock
Anti-LiftGuard
INTERIOR
3 B
11
A
B
INTERIOR
Slide door to wall and check vertical reveal. See Page 8 to adjust wheel height. Tighten securely when finished.
2CL90S_(Not Included).
SLIDING DOOR INSTALLATION Install Sliding Door
Install Anti-Lift Guides
MESSINA HEADERLESS SLIDING SHOWER DOOR
USHORIZONushorizon.com 10
2 C
C1
D1
Remove protectiveliner fromL-Seal.
Close Door soL-Seal adheres to wall.
INTERIORE1
F1Open Door and push seal firmly
into place.
Remove painter’stape from Door.
INTERIOR
INTERIOR
2
1
Install Bumpers at Wall Mounts.
Cut and install L-Seal.NOTE: Temporarily attach L-Seal to Sliding Door and use as guide for final position.
NOTE: Wall Brackets not included. CL90S_ shown asexample only. Some brackets may have holes predrilled.
L-Seal
INTERIOR
CutL-SealLength
Top ofGlassDoor
Top ofBottomTrack
A
Align L-Sealto top
of glass.Temorarilyattach toDoor with
painter’s tape.
B1
INTERIOR
InstallBumpers
withIncludedScrews.
2 C
2 C
CL90S_(Not Included).
2
2 C
C
A2
Close Door to mark position for Bumpers.
Open Door to drill holes.
2 B
Position Bumpers to align with Sliding Door at Wall Brackets. Attach to wall.
NOTE: CL90S_Wall Mounts
(Not Included).Shown as
example only.
FINISHINGInstall L-Seal
Install Bumpers