upload.doc
4
wk MODULE 12 STRUCTURAL DESIGN AND DETAILING (60 Hours, 4 Credits) 22.07. 13 24.07. 13 C1 Overview of structural design Explain and locate Neutral axis Explain dead loads, imposed loads and wind loads. Calculate design load for ultimate and serviceability limit state. Explain serviceability limit state in terms of deflection, cracking, durability, fire resistance 29.07. 13 31.07. 13 05.08. 13 07.08. 13 C2 Demonstrate knowledge of the design methods of reinforced concrete rectangular beams. Calculate the moment of resistance for a singly reinforced section. Calculate minimum amount of longitudinal bars and stirrups. Explain Bar Spacing rules. Design a continuous rectangular beam for compression and tension steel. Illustrate standard detailing practice. Draw beam section and elevation. Carry out reinforcement detailing and describe curtailment of bars. 12.08. 13 14.08. 13 C3 Design solid slabs Carry out preliminary sizing of slabs using span- effective depth ratio. Design slabs for bending spanning in one direction
Transcript of upload.doc
wkMODULE 12 STRUCTURAL DESIGN AND DETAILING (60 Hours, 4 Credits)
22.07.13
24.07.13
C1
Overview of structural design Explain and locate Neutral axis
Explain dead loads, imposed loads and wind loads.
Calculate design load for ultimate and serviceability limit state.
Explain serviceability limit state in terms of deflection, cracking, durability, fire resistance
29.07.13
31.07.13
05.08.13
07.08.13
C2Demonstrate knowledge of the design methods of reinforced concrete rectangular beams.
Calculate the moment of resistance for a singly reinforced section.
Calculate minimum amount of longitudinal bars and stirrups.
Explain Bar Spacing rules.
Design a continuous rectangular beam for compression and tension steel.
Illustrate standard detailing practice.
Draw beam section and elevation.
Carry out reinforcement detailing and describe curtailment of bars.
12.08.13
14.08.13
C3Design solid slabs
Carry out preliminary sizing of slabs using span-effective depth ratio.
Design slabs for bending spanning in one direction and check for deflection.
Carry out reinforcement detailing and describe curtailment of bars.
19.08.13
21.08.13
C4Demonstrate knowledge of the Design Of Short And Slender Columns
Differentiate between short columns.
Design short braced column(axially loaded / supporting an approximate symmetrical arrangement of beams)
Design short columns resisting moments and axial forces using design chart.
Describe reinforcement details.
26.08.13
28.08.13
02.09.13
C5
wkMODULE 12 STRUCTURAL DESIGN AND DETAILING (60 Hours, 4 Credits)
22.07.13
24.07.13
C1
Overview of structural design Explain and locate Neutral axis
Explain dead loads, imposed loads and wind loads.
Calculate design load for ultimate and serviceability limit state.
Explain serviceability limit state in terms of deflection, cracking, durability, fire resistance
29.07.13
31.07.13
05.08.13
07.08.13
C2Demonstrate knowledge of the design methods of reinforced concrete rectangular beams.
Calculate the moment of resistance for a singly reinforced section.
Calculate minimum amount of longitudinal bars and stirrups.
Explain Bar Spacing rules.
Design a continuous rectangular beam for compression and tension steel.
Illustrate standard detailing practice.
Draw beam section and elevation.
Carry out reinforcement detailing and describe curtailment of bars.
12.08.13
14.08.13
C3Design solid slabs
Carry out preliminary sizing of slabs using span-effective depth ratio.
Design slabs for bending spanning in one direction and check for deflection.
Carry out reinforcement detailing and describe curtailment of bars.
19.08.13
21.08.13
C4Demonstrate knowledge of the Design Of Short And Slender Columns
Differentiate between short columns.
Design short braced column(axially loaded / supporting an approximate symmetrical arrangement of beams)
Design short columns resisting moments and axial forces using design chart.
Describe reinforcement details.
25.09.13
30.09.13
02.10.13
07.10.13
09.10.13
15.10.13
