Universal Waste Training Alfred University Environmental Health & Safety.

36
Universal Waste Training Alfred University Environmental Health & Safety

Transcript of Universal Waste Training Alfred University Environmental Health & Safety.

Page 1: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Training

Alfred University

Environmental Health & Safety

Page 2: Universal Waste Training Alfred University Environmental Health & Safety.

Why are we here?

• Universal Waste Training Requirement for Small Quantity Handlers:– New York State requires that: “A small

quantity handler of universal waste must inform all employees who handle or have responsibility for managing universal waste. The information must describe proper handling and emergency procedures appropriate to the type(s) of universal waste handled at the facility.” (6NYCRR 374-3.2 (g))

Page 3: Universal Waste Training Alfred University Environmental Health & Safety.

What are Universal Wastes?

• Universal Wastes are certain hazardous wastes that are universally generated in large quantities by industrial facilities but present a limited hazard.

• They are exempt from the hazardous waste regulations, but must still be managed separately from general trash.

Page 4: Universal Waste Training Alfred University Environmental Health & Safety.

What are Universal Wastes? (cont.)

• There are five (5) categories of universal waste, which include:

• lamps• lamp ballasts;• universal waste batteries;• pesticides; and• mercury-containing equipment.

Page 5: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamps

• Universal waste lamps consist of:– fluorescent lamps and ballasts;– high intensity lamps;– neon lamps;– mercury vapor lamps;– high pressure sodium lamps; and– metal halide lamps.

• Incandescent bulbs are non-hazardous and may be thrown in regular trash.

Page 6: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamps ProperHandling Procedures

• Lamps must be placed in containers or packages that are structurally sound, adequate to prevent breakage, and compatible with the contents of the lamps, i.e. fiber box or drum.

• It is common practice across AU and recommended that the original box which the lamp was purchased in be used to store the waste lamp. Therefore, please ensure that you keep these containers.

• Containers and packages must remain closed unless adding or removing lamps and must lack evidence of leakage, spillage or damage that could cause leakage under reasonably foreseeable conditions.

• Do not tear the flaps off of the lamp containers and tape the flaps closed when lamps are not being added to the container.

Page 7: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamps Proper Handling Procedures (Cont.)

– As soon as the first lamp (if multiple lamps are being stored in a single container) is placed in the container then the container must be labeled with the words Universal Waste-Lamp(s) and must be dated.

– Dependant on how your Division is set-up, you may either bring the universal waste to a designated storage area or create a designated storage area where the waste is generated.

– There is a one year limit that universal waste lamps can be stored at AU.

Universal waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Note: There are different labels and palette contents list for AU and NYS College of Ceramics at AU with different addresses. Make sure you use the correct label and list for your containers and palettes.

Page 8: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamps Emergency Procedures

If a lamp breaks or shows evidence of leakage, spillage, or damage you must:

• immediately clean up the broken lamp and place the pieces or damaged lamp in a UN approved container;

• the containers must be closed, structurally sound, and compatible with the contents of the lamps;

• The containers must lack evidence of leakage, spillage or damage that could cause leakage or releases of mercury or other hazardous constituents to the environment under reasonably foreseeable conditions.

Page 9: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamps Emergency Procedures (Cont.)

The container would now be classified as a hazardous waste and must be managed accordingly. This includes properly labeling the container and ensuring that it is brought to a Central Accumulation Area within 72 hours of the full date. The date that the container is brought to the CAA should be filled in on the label.

SAA, Chemical and Hazardous Waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Page 10: Universal Waste Training Alfred University Environmental Health & Safety.

How should I clean up a broken fluorescent bulb?

• 1. Open a window and leave the room for 15 minutes or more.

• 2. Carefully scoop up the fragments and powder with stiff paper or cardboard and place them in a sealed plastic bag.

Use disposable rubber gloves, if available (i.e., do not use bare hands). Wipe the area clean with damp paper towels or disposable wet wipes and place them in the plastic bag.

Do not use a vacuum or broom to clean up the broken bulb on hard surfaces.

• 3. Place all cleanup materials in a second sealed plastic bag.

Place the first bag in a second sealed plastic bag and put it in the outdoor trash container or in another outdoor protected area for the next normal trash disposal.

Note: some states prohibit such trash disposal and require that broken and unbroken lamps be taken to a local recycling center.

Wash your hands after disposing of the bag.

• 4. If a fluorescent bulb breaks on a rug or carpet:

First, remove all materials you can without using a vacuum cleaner, following the steps above. Sticky tape (such as duct tape) can be used to pick up small pieces and powder.

If vacuuming is needed after all visible materials are removed, vacuum the area where the bulb was broken, remove the vacuum bag (or empty and wipe the canister) and put the bag or vacuum debris in two sealed plastic bags in the outdoor trash or protected outdoor location for normal disposal.

Universal Waste Lamps Emergency Procedures (Cont.)

Page 11: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamp Ballasts

Proper Handling Procedures

• Store universal waste ballasts in a UN approved 5 gallon plastic container with the proper label affixed and filled-out.

• Separate PCB containing ballasts from non-PCB containing and note on the label.

• When container is full write the total number of ballasts in that container on the label.

Page 12: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamp Ballasts Proper Handling Procedures (Cont.)

• When the first ballast is placed in the container the container must be labeled with the words Universal Waste-Ballasts and must be dated.

• Dependant on how your Division is set- up, you may either bring the universal waste to a designated storage area or create a designated storage area where the waste is generated.

• There is a one year limit that universal waste ballasts can be stored at AU.

Universal waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Note: There are different labels and palette contents list for AU and NYS College of Ceramics at AU with different addresses. Make sure you use the correct label and list for your containers and palettes.

Page 13: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Lamp Ballast Emergency Procedures

• If the casing of a ballast is breached or shows evidence of leakage, spillage, or damage, the ballast and any associated spilled material must be placed in a UN approved container. The container must be closed, structurally sound, compatible with the contents of the battery, and must lack evidence of leakage, spillage, or damage that could cause leakage under reasonably foreseeable conditions.

• The container would now be classified as a hazardous waste and must be managed accordingly. This includes properly labeling the container and ensuring that it is brought to a Central Accumulation Area within 72 hours of the full date. The date that the container is brought to the CAA should be filled in on the label.

SAA, Chemical or Hazardous Waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Page 14: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Batteries

• Universal Waste Batteries consist of:– Nickel-Cadmium batteries;– Metal hydride batteries;– Lead-acid batteries;– Silver oxide– Mercury oxide;– Lithium;– Zinc air; and– Zinc carbon.

• These batteries are commonly used in pagers, cell phones, cameras, and computers.

• Alkaline batteries (e.g., AA, AAA, C, etc.) are non-hazardous and may be thrown in regular trash

Page 15: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Batteries

Proper Handling Procedures

• It is recommended that universal waste batteries be stored in a UN approved 5 gallon plastic container with the proper label affixed and filled-out.

• Cover positive and negative terminals (electricians tape or a similar material works well) prior to placing in the container.

Page 16: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Batteries Proper Handling Procedures (Cont.)

• If you choose to label each battery individually, then you must label each with the words Universal Waste-Batteries and with the date it became a waste.

• If you choose to place each battery in a larger container, then as soon as the first battery is placed in the container the container must be labeled with the words Universal Waste-Batteries and must be dated.

• Dependant on how your Division is set- up, you may either bring the universal waste to a designated storage area or create a designated storage area where the waste is generated.

• There is a one year limit that universal waste batteries can be stored at AU.

Universal waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Note: There are different labels and palette contents list for AU and NYS College of Ceramics at AU with different addresses. Make sure you use the correct label and list for your containers and palettes.

Page 17: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Batteries Emergency Procedures

• If the casing of a battery is breached or shows evidence of leakage, spillage, or damage, the battery and any associated spilled material must be placed in a UN approved container. The container must be closed, structurally sound, compatible with the contents of the battery, and must lack evidence of leakage, spillage, or damage that could cause leakage under reasonably foreseeable conditions.

• The container would now be classified as a hazardous waste and must be managed accordingly. This includes properly labeling the container and ensuring that it is brought to a Central Accumulation Area within 72 hours of the full date. The date that the container is brought to the CAA should be filled in on the label.

SAA, Chemical or Hazardous Waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Page 18: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Pesticides

• No AU employee should have any pesticides in storage unless they are certified with the New York State Department of Environmental Conservation to apply such pesticides.

• Pesticide is defined as “any substance or mixture of substances intended for preventing, destroying, repelling, or mitigating any pest, or intended for use as a plant regulator, defoliant, or desiccant.”

Page 19: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Pesticides Proper Handling Procedures

• Universal waste pesticides must be contained in a properly labeled container that remains closed, structurally sound, compatible with the pesticide, and that lacks evidence of leakage, spillage, or damage that could cause leakage under reasonably foreseeable conditions.

• If the original manufacturers container does not meet this requirement then this unacceptable container must be over-packed in a container that does meet this requirement.

Page 20: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Pesticides Proper Handling Procedures (Cont.)

• Each universal waste pesticide container must be labeled or marked clearly with:

– The label that was on or accompanied the product as sold or distributed; and the words “Universal Waste - Pesticides.”

– The date the pesticide was classified as a waste. There is a one year limit that universal waste pesticides can be stored at AU.

• Dependant on how your Division is set- up, you may either bring the universal waste to a designated storage area or create a designated storage area where the waste is generated.

Universal waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Note: There are different labels and palette contents list for AU and NYS College of Ceramics at AU with different addresses. Make sure you use the correct label and list for your containers and palettes.

Page 21: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste PesticidesEmergency Procedures

• If the container storing universal waste pesticides is breached or shows evidence leakage, spillage, or damage, the pesticide and any associated spilled material must be immediately placed in a UN approved container. The container must be closed, structurally sound, compatible with the contents of the battery, and must lack evidence of leakage, spillage, or damage that could cause leakage under reasonably foreseeable conditions.

• The container would now be classified as a hazardous waste and must be managed accordingly. This includes properly labeling the container and ensuring that it is brought to a Central Accumulation Area within 72 hours of the full date. The date that the container is brought to the CAA should be filled in on the label..

SAA, Chemical or Hazardous Waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Page 22: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Mercury-Containing Equipment

• Mercury-Containing Equipment (MCE) is defined a device or part of a device that contains elemental mercury integral to its function.

• Various types of MCE waste include instruments that are used in industry, hospitals and households.

• Some commonly recognized items include, but are not limited to, thermometers, thermostats, barometers, manometers, temperature and pressure gauges, and mercury switches.

Page 23: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Mercury-Containing Equipment Proper Handling Procedures

• Universal waste MCE must be managed in a way that prevents releases of any universal waste or component of a universal waste to the environment.

• The MCE must be labeled with the words “Universal Waste – Mercury-Containing Equipment” and must also be labeled with the date they became a waste. There is a one year limit that universal waste MCE can be stored at AU.

• Dependant on how your Division is set- up, you may either bring the universal waste to a designated storage area or create a designated storage area where the waste is generated.

Universal waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Note: There are different labels and palette contents list for AU and NYS College of Ceramics at AU with different addresses. Make sure you use the correct label and list for your containers and palettes.

Page 24: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Mercury-Containing Equipment Emergency Procedures

• Any universal waste MCE that shows evidence of leakage, spillage, or damage that could cause leakage under reasonably foreseeable conditions must be placed in a UN approved container. The container must be closed, structurally sound, compatible with the contents of the MCE and must lack evidence of leakage, spillage, or damage that could cause leakage under reasonably foreseeable conditions.

• The container would now be classified as a hazardous waste and must be managed accordingly. This includes properly labeling the container and ensuring that it is immediately brought to a 90-day hazardous waste vault. The date that the containers is brought to the vault should be filled in on the label.

SAA, Chemical or Hazardous Waste labels may be downloaded from the following EH&S web site link:http://people.alfred.edu/~envhealthsafety/signlabel.htm

Page 25: Universal Waste Training Alfred University Environmental Health & Safety.

General Rule• Keep in mind that materials you use at home for

your personal use and dispose of in your household trash may be considered hazardous when used and disposed of at AU

• Always think before you throw something in the trash at AU – Contact EH&S at x2190 if you have questions about proper disposal of any waste, material, products or chemicals.

Page 26: Universal Waste Training Alfred University Environmental Health & Safety.

Universal Waste Transport Preparations at Alfred University

• Typical Universal Waste Pick-up Locations – Music Annex and Binns-Merrill Hall loading dock

• Pick-up Requirements:

1) Universal waste containers must be palletized and plastic-wrapped prior to loading on transport vehicle.

2) A fork truck and driver will need to be available at time of pick-up for loading

3) Each universal waste container must be appropriately labeled and each universal waste palette must have a completed universal waste palette contents list filed with EH&S at least five days in advance of the scheduled pick-up date.

Note: There are different labels and palette contents list for AU and NYS College of Ceramics at AU with different addresses. Make sure you use the correct label and list for your containers and palettes.

Page 27: Universal Waste Training Alfred University Environmental Health & Safety.

Emergency ResponseIn the event of an emergency (e.g., fire, spill, leaking waste

containers) – reference emergency information folder,

Alfred University Emergency Response Information:– Call 911 (9-911 from campus phones) and Public Safety at x2108– Secure and exit the area– Activate building alarm system if deemed

necessary– Meet emergency responders

Page 28: Universal Waste Training Alfred University Environmental Health & Safety.

Alfred University Resources

AU EH&S Web Links:• http://our.alfred.edu/index.cfm/fuseaction/ehs.first.cfm• http://people.alfred.edu/~envhealthsafety/signlabel.htm• http://people.alfred.edu/~envhealthsafety/training.htm

AU Public Safety Web Link:• http://our.alfred.edu/index.cfm/fuseaction/safety.home.cfm

UN Approved Containers (for reference only):• http://www.kaplancontainer.com/

Additional Links:• http://people.alfred.edu/~envhealthsafety/wwwlinks.htm

Page 29: Universal Waste Training Alfred University Environmental Health & Safety.

Enforcement, Fines & Penalties

Two regulatory agencies that oversee universal waste compliance in New York are:• State - NYS Department of Environmental Conservation (NYSDEC)• Federal – United States Environmental Protection Agency (USEPA)

*Both can proceed with civil or criminal prosecution for hazardous waste violations

Page 30: Universal Waste Training Alfred University Environmental Health & Safety.

Enforcement, Fines & Penalties (cont.)

• Individuals may be criminally prosecuted for knowingly:– Transporting waste to non-permitted facility– Improper disposal of hazardous wastes/universal waste

(including down drain, in general trash, etc.)– Making false statements on any label, record, report or other

form used for compliance purposes

• Individual criminal penalties may consist of:– $50,000 fine for each day of violation, and/or

Prison sentence of 2-5 years

Page 31: Universal Waste Training Alfred University Environmental Health & Safety.

Questions:

1. Universal Wastes are considered to?a) Pose limited hazard but are still a form of hazardous waste.

b) Be extremely hazardous and pose a serious threat.

c) Pose no hazard and can be thrown in the trash.

d) Not be found anywhere on our campus.

2. All of the following are classified as Universal Waste except?a) Lamps.

b) Mercury Manometer.

c) Pesticides.

d) Computer monitor.

Page 32: Universal Waste Training Alfred University Environmental Health & Safety.

Questions continued:

3. Universal waste must be?a) In a structurally sound UN approved container to prevent spillage.b) Labeled as universal waste. c) Stored on campus for less than 1 year.d) All of the above.

4. If a universal waste lamp breaks or shows evidence of leakage, spillage or damage it now must be labeled as?

a) Universal waste.b) Hazardous waste and placed in Central Accumulation Area when UN

approved storage container is full.c) Broken.d) Not labeled and thrown away immediately.

Page 33: Universal Waste Training Alfred University Environmental Health & Safety.

Questions continued:

5. Which of the following would be considered Mercury-Containing Equipment?

a) Barometer.

b) Thermostat.

c) Thermometer.

d) All of the above.

6. True/False. An alkaline battery is considered non-hazardous and can be put in the general waste stream (trash).

Page 34: Universal Waste Training Alfred University Environmental Health & Safety.

Questions continued:

7. Which of the following lamps/bulbs are not classified as universal waste?a) fluorescent lamps.

b) high intensity lamps.

c) neon lamps.

d) Incandescent bulbs.

8. True/False. Those things that you use at home and dispose of in your trash could be considered hazardous waste here at AU.

Page 35: Universal Waste Training Alfred University Environmental Health & Safety.

Questions continued:

9. The two regulatory agencies that oversee universal waste compliance are?a) NYSERDA and NRC

b) NYS DEC and the US EPA

c) Alfred Fire Department and NIOSH

d) OSHA and NFPA.

10. Which is the proper way to manage Universal Waste Batteries?a) Place each battery in a container and label the container.

b) Label each battery separately.

c) Do not label either the individual battery or the container.

d) Either a or b.

Page 36: Universal Waste Training Alfred University Environmental Health & Safety.

Please complete this answer sheet for the quiz questions, obtainsupervisor ‘s signature, sign and date at the bottom of this answer sheet and campus mail to: Myers Hall Rm. 117, EH&S or fax to: x2086.

Supervisor Signature: _________________________

Print Name: _______________________________

Signature: ________________________________Date: ______________________

Instructions: Using a blue or black pen, place a circle around the best answer.

1) A B C D

2) A B C D

3) A B C D

4) A B C D

5) A B C D

6) True False

7) A B C D

8) True False

9) A B C D

10) A B C D

Note: Universal Waste training at AU is required upon hire and annually thereafter. AU employees who typically manage universal waste are physical plant, maintenance, custodians and technicians. You will receive credit for this training once the EH&S office has received and scored your quiz.