Unit-2 Polarization and Dispersion. One Dimensional EM Wave For most purposes, a travelling light...
-
Upload
james-turner -
Category
Documents
-
view
222 -
download
2
Transcript of Unit-2 Polarization and Dispersion. One Dimensional EM Wave For most purposes, a travelling light...
Unit-2
Polarization and Dispersion
One Dimensional EM Wave• For most purposes, a travelling light wave can be presented as a one-dimensional, scalar wave provided it has a direction of propagation.• Such a wave is usually described in terms of the electric field E.
)sin(),( ztEtzE o
A plane wave propagating in the direction of z is:
The propagation constant (or wave number)
Wavelength
Eo
Phase
z
pv
2
Phase velocity ncvp / n = Propagation medium refractive index
Group Velocity• As monochromatic light wave propagates along a waveguide in the z direction, the points of constant phase travel at a phase velocity.
Phase velocity ncvp /
• However, non-monochromatic waves travelling together will have a velocity known as Group Velocity: gncvg /
d
dnnng
Where the fibre group index is:
1.44
1.46
1.49
500 1700 1900
n
ng
(nm)
Ref
. in
dex
Classification of Polarization
Light in the form of a plane wave in space is said to be linearly polarized.
If light is composed of two plane waves of equal amplitude by differing in phase by 90°, then the light is said to be circularly polarized.
If two plane waves of differing amplitude are related in phase by 90°, or if the relative phase is other than 90° then the light is said to be elliptically polarized.
Linear Polarization
A plane electromagnetic wave is said to be linearly polarized.
The transverse electric field wave is accompanied by a magnetic field wave as illustrated.
Circular Polarization
Circularly polarized light consists of two perpendicular electromagnetic plane waves of equal amplitude and 90° difference in phase.
The light illustrated is right- circularly polarized.
Elliptical Polarization
Elliptically polarized light consists of two perpendicular waves of unequal amplitude which differ in phase by 90°.
The illustration shows right- elliptically polarized light.
Fiber Dispersion
Fibre Dispersion• Data carried in an optical fibre consists of pulses of light energy consists of a large number of frequencies travelling at a given rate.• There is a limit to the highest data rate (frequency) that can be sent down a fibre and be expected to emerge intact at the output. • This is because of a phenomenon known as Dispersion (pulse spreading), which limits the "Bandwidth” of the fibre.
L
si(t)
T
so(t)Outputpulse
Cause of Dispersion:• Chromatic (Intramodal) Dispersion• Modal (Intermodal) Dispersion
Many modes
Effects of Dispersion and Attenuation
Definitions
Group velocity
Group delay
Dispersion
1
gv
kc
1
D
Group and Phase Velocity
The formation of a wave packet from the combination of two waves with nearly equal frequencies. The envelope of the wave package or group of waves travels at a group velocity vg.
Chromatic/Intramodal Dispersion
• Intramodal dispersion arises due to the propagation delay differences between the different spectral components of the transmitted signal.
•Further it increases with the increase in spectral width of the optical source.
• This spectral width is the range of wavelengths emitted by the optical source.
• For example in the case of LED, it has a large spectral width about 40 nm since it emits wavelengths from 830–870 nm with the peak emission wavelength at 850 nm.
•In the case of laser diode which has a very narrow spectral width, the spectral width is about 1 or 2 nm only.
•Thus the Intramodal dispersion can be reduced in an optical fiber using single mode laser diode as an optical source.
Laser
LED(many modes)
wavelength
= 40 nm
= 1-2 nm
= R.M.S Spectral width
Chromatic/Intramodal Dispersion
• Main causes: • Material dispersion • Waveguide dispersion
Material Dispersion• This dispersion arises due to the different group velocities of the various spectral
components launched into the fiber.
• A material is said to exhibit material dispersion when
• Pulse spreading occurs even when different wavelengths follow the same path.
• Sometimes referred to as Chromatic dispersion ,
since this is the same effect by
which a prism spreads out
a spectrum.
In a prism, material dispersion (a wavelength-dependent refractive index) causes different colors to refract at different angles, splitting white light into a rainbow
t
Spread, ²
t0
Spectrum, ²
12o
Intensity Intensity Intensity
Cladding
CoreEmitter
Very shortlight pulse
vg(2)
vg(1)Input
Output
All excitation sources are inherently non-monochromatic and emit within aspectrum, ² , of wavelengths. Waves in the guide with different free spacewavelengths travel at different group velocities due to the wavelength dependenceof n1. The waves arrive at the end of the fiber at different times and hence result ina broadened output pulse.
© 1999 S.O. Kasap, Optoelectronics (Prentice Hall)
Material Dispersion
Material DispersionRefractive index of silica is frequency dependent. Thus differentfrequency (wavelength) components travel at different speed
kmnsd
nd
cLmat /
2
2
RMS pulse broadening
2
2
d
nd
cDmat
Where material dispersion coefficient:
kmnmps ./
Note: Negative sign, indicates that low wavelength components arrives before higher wavelength components.
0.8 1.0 1.2 1.4 1.6 1.7
0
-100
100
175
Dmat
2nd window
Waveguide Dispersion• This results from variation of the group velocity with wavelength for a particular mode.
• Signal in the cladding travels with a different velocity than the signal in the core
• The amount of waveguide dispersion depends on the fiber design like core radius and the size of the fiber.
•This can usually be ignored in multimode fibres, since it is very small compared with material dispersion.
•However it is significant in monomode fibres.
Waveguide Dispersion• In the case of single mode fibers, waveguide dispersion arises when
0.8 1.0 1.2 1.4 1.6 1.7
0
-100
100
175
Dmat
Waveguide dispersion
Total dispersion
Material dispersion
Modifying Chromatic Dispersion
Modal (Intermodal) Dispersion
• Result of different values of the group delay for each individual mode at a single frequency.
• This variation in the group velocities of the different modes results in a group delay spread of intermodal distortion.
• This distortion mechanism is eliminated by single-mode operation, but it is important in multimode fibers.
Modal (Intermodal) Dispersion• Lower order modes travel almost parallel to the centre line of the fibre cover the shortest distance, thus reaching the end of fibre sooner.
• The higher order modes (more zig-zag rays) take a longer route as they pass along the fibre and so reach the end of the fibre later.
• Mainly in multimode fibers
1
2Cladding n2
Core n1c
Modal Dispersion - SIMMF
The time taken for ray 1 to propagate a length of fibre L gives the minimum delay time: c
Lnt 1min
The time taken for the ray to propagate a length of fibre L gives the maximum delay time:
1max
cos
nc
Lt
2
21
cn
LnTs Thus
1
21 )(
n
nn Since relative refractive index
difference
Since
The delay difference minmax ttTs cossin
1
2
n
nc
Modal Dispersion - SIMMF
Total dispersion = chromatic dispersion + modal dispersion
For 1, 5.01 )2( nNA
2
21 )(
n
nn and
1
2
2
)(
cn
NALTs
For a rectangular input pulse, the RMS pulse broadening due to modal dispersion at the output of the fibre is:
c
Lnal 5.3
1mod
2/122 ][ modalchromT
c
LnTs
1Thus
Modal Dispersion - GIMMF
• The delay difference
• the RMS pulse broadening
c
LnTs 2
21
c
LnGImodal 6.34
21
Modal Dispersion - GIMMF
• Intermodal dispersion in multimode fibers is minimized with the use of graded index fibers.
• Hence multimode graded index fibers show substantial bandwidth improvement over multimode step index fibers.
• The fiber has a parabolic index profile with a maximum at the core axis.
Step and Graded Index Fibers
Modal Dispersion - GIMMF• It may be observed that apart from the axial ray the meridional rays follow sinusoidal
trajectories of different path lengths which results from the index grading.
• The longer sinusoidal paths are compensated for by the higher speeds in the lower index medium away from the axis.
• The ray that travels along the axial ray is exclusively in the high index region at the core axis, and at the lowest speed.
• Thus there is an equalization of the transmission times of the various trajectories and the graded index profile reduces the disparity in the mode transit times.
• Thus the delay difference between the fastest and slowest modes are reduced for graded index fiber.
Problem
Problem
Bandwidth Limitations• Maximum channel bandwidth B:
• For non-return-to-zero (NRZ) data format: B = BT /2• For return-to-zero (RZ) data format: B = BT
Where the maximum bit rate BT = 1/T, and T = bit duration.
• For zero pulse overlap at the output of the fibre BT <= 1/2 where is the pulse width. For MMSF: BT (max) = 1/2Ts
• For a Gaussian shape pulse:BT 0.2/rms
where rms is the RMS pulse width. For MMSF: BT (max) =0.2/ modal
or BT (max) =0.2/ T Total dispersion
Bandwidth Distance Product (BDP)The BDP is the bandwidth of a kilometer of fibre and is a constant for any particular type of fibre. Bopt * L = BT * L (MHzkm)
For example, A multimode fibre has a BDP of 20 MHz.km, then:-
- 1 km of the fibre would have a bandwidth of 20 MHz - 2 km of the fibre would have a bandwidth of 10 MHz
Typical B.D.P. for different types of fibres are:
• Multimode 6 - 25 MHz.km• Single Mode 500 - 1500 MHz.km• Graded Index 100 - 1000 MHZ.km
Polarization Mode Dispersion
Polarizations of fundamental mode
Birefringence in single-mode fibers
• Because of asymmetries the refractive indices for the two degenerate modes (vertical & horizontal polarizations) are different. This difference is referred to as birefringence, :fB
xyf nnB
Optical Fiber communications, 3rd ed.,G.Keiser,McGrawHill, 2000
Birefringence in single-mode fibers
• The effects of fiber birefringence on the polarization states of an optical signal are another source of pulse broadening.
• Results from intrinsic factors such as geometric irregularities of the fiber core or internal stresses on it.
• External factors such as bending, twisting or pinching of the fiber can also lead to birefringence.
• All these mechanisms exist to some extent in the fiber, there will be a varying birefringence along its length.
Polarization Mode dispersion
Core
z
n1 x
// x
n1 y
// y
Ey
Ex
Ex
Ey
E
= Pulse spread
Input light pulse
Output light pulset
t
Intensity
Suppose that the core refractive index has different values along two orthogonaldirections corresponding to electric field oscillation direction (polarizations). We cantake x and y axes along these directions. An input light will travel along the fiber with Ex
and Ey polarizations having different group velocities and hence arrive at the output atdifferent times
© 1999 S.O. Kasap, Optoelectronics (Prentice Hall)
Fiber Beat Length
• In general, a linearly polarized mode is a combination of both of the degenerate modes. As the modal wave travels along the fiber, the difference in the refractive indices would change the phase difference between these two components & thereby the state of the polarization of the mode. However after certain length referred to as fiber beat length, the modal wave will produce its original state of polarization. This length is simply given by:
FFB BkB
L
2
Fiber Beat Length