UNIT 2 DIGITAL COMMUNICATION DIGITAL …...Getmynotes.com Course Material (Lecture Notes) UNIT 2...
Transcript of UNIT 2 DIGITAL COMMUNICATION DIGITAL …...Getmynotes.com Course Material (Lecture Notes) UNIT 2...
Getmynotes.com Course Material (Lecture Notes)
UNIT 2
DIGITAL COMMUNICATION
DIGITAL COMMUNICATION-Introduction
The techniques used to modulate digital information so that it can be transmitted via microwave,
satellite or down a cable pair is different to that of analogue transmission. The data transmitted
via satellite or microwave is transmitted as an analogue signal. The techniques used to transmit
analogue signals are used to transmit digital signals. The problem is to convert the digital signals
to a form that can be treated as an analogue signal that is then in the appropriate form to either be
transmitted down a twisted cable pair or applied to the RF stage where is modulated to a
frequency that can be transmitted via microwave or satellite.
The equipment that is used to convert digital signals into analogue format is a modem.
The word modem is made up of the words ―modulator and ―‖ demodulator .‖
A modem accepts a serial data stream and converts it into an analogue format that matches
the transmission medium.
There are many different modulation techniques that can be utilized in a modem. These
techniques are:
x Amplitude shift key modulation (ASK)
x Frequency shift key modulation (FSK)x Binary-phase shift key modulation (BPSK)x Quadrature-phase shift key modulation (QPSK)x Quadrature amplitude modulation (QAM)
Amplitude Shift Key Modulation
In this method the amplitude of the carrier assumes one of the two amplitudesdependent on the logic states of the input bit stream. A typical output waveform of an ASKmodulator is shown in the figure below. The frequency components are the USB and LSBwith a residual carrier frequency. The low amplitude carrier is allowed to be transmitted toensure that at the receiver the logic 1 and logic 0 conditions can be recognized uniquely.
The ON-OFF signaling variety=
, 10, 0
CS6304-Analog & Digital Communication UNIT-2 Page 1
Getmynotes.com
Getmynotes.com Course Material (Lecture Notes)
2=
cos(2 ) ,1
0, 0
The average transmitted signal energy is (the two binary symbols must by equiprobable)
Eav = Eb /2
FREQUENCY SHIFT KEYING
CS6304-Analog & Digital Communication UNIT-2 Page 2
Getmynotes.com
Getmynotes.com Course Material (Lecture Notes)
If the bit intervals and the phases of the signals can be determined (usually by the use of a
phase-lock loop), then the signal can be decoded by two separate matched filters:
The first filter is matched to the signal s1.t/, and the second to s2.t/. Under the
assumption that the signals are mutually orthogonal, the output of one of the matched filterswill be E and the other zero (where E is the energy of the signal). Decoding of the bandpasssignal can therefore be achieved by subtracting the outputs of the two filters, and comparingthe result to a threshold.
CS6304-Analog & Digital Communication UNIT-2 Page 3
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
If the signal s1.t/ is present then the resulting output will be CE, and if s2.t/ is present it will be E. Since the noise variance at each filter output is E =2, the noise in the difference
signal will be doubled, namely 2 D E . Since the overall output variation is 2E, the probabilityof error is
The overall performance of a matched filter receiver in this case is therefore the same as
for ASK.
The frequency spectrum of an FSK signal is difficult to obtain — this is a general characteristic of FM signals. However, some rules of thumb can be developed. Consider thecase where the binary message consists of an alternating sequence of zeros and ones. If the
two frequencies are each multiples of 1= T (eg. f1 D m= T and f2 D n= T ) and are synchronised in phase, then the FSK wave is a periodic function:
FSK signal
This can be viewed as the linear superposition of two OOK signals, one delayed by T
seconds with respect to the other. Since the spectrum of an OOK signal is
CS6304-Analog & Digital Communication UNIT-2 Page 4
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 5
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 6
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 7
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 8
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 9
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 10
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 11
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 12
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 13
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
Phase Shift Key Modulation
With this method the phase of the carrier changes between different phases determined by the
logic states of the input bit stream.
There are several different types of phase shift key (PSK) modulators.
x Two-phase (2 PSK)
x Four-phase (4 PSK)
x Eight-phase (8 PSK)
x Sixteen-phase (16 PSK)
x Sixteen-quadrature amplitude (16 QAM)
The 16 QAM is a composite modulator consisting of amplitude modulation and phase
modulation. The 2 PSK, 4 PSK, 8 PSK and 16 PSK modulators are generally referred to
as binary phase shift key (BPSK) modulators and the QAM modulators are referred to as
quadrature phase shift key (QPSK) modulators.
Two-Phase Shift Key Modulation
In this modulator the carrier assumes one of two phases. A logic 1 produces no phase change anda logic 0 produces a 180° phase change. The output waveform for this modulator is shown
below.
CS6304-Analog & Digital Communication UNIT-2 Page 14
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 15
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 16
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 17
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 18
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
Four-Phase Shift Key Modulation
With 4 PSK, 2 bits are processed to produce a single phase change. In this case each symbol
consists of 2 bits, which are referred to as a dibit. The actual phases that are produced by a 4 PSK
modulator are shown in the table below.
CS6304-Analog & Digital Communication UNIT-2 Page 19
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
Eight-Phase Shift Key Modulation
With this modulator 3 bits are processed to produce a single phase change. This means that each
symbol consists of 3 bits.
8 PSK Modulator
Figure 10 above shows a typical circuit for the 8 PSK modulator. With this modulator bit A
controls the output polarity of the first digital-to-analogue converter (DAC1). Bit B is used to
control the output polarity of the second DAC 2 and bit C is used to control the output amplitude
of both DACs.
Digital to Analogue Conversion Condition for 8 PSK modulator
The conditions shown in the table above produce the positions shown in table below for all the
different permutations.
CS6304-Analog & Digital Communication UNIT-2 Page 20
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
Input permutations and Positions
The constellation diagram can be drawn according to the above table and is shown below.
Sixteen-Phase Shift Key Modulation
With this modulator 4 bits are processed to produce a single phase change. This means that each
symbol consists of 4 bits. The constellation for this modulator scheme is shown below.
CS6304-Analog & Digital Communication UNIT-2 Page 21
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
16 PSK Modulation Constellation
Quadrature Phase Shift Keying (QPSK)
An important goal of digital communication is the efficient utilization of channel bandwidth
CS6304-Analog & Digital Communication UNIT-2 Page 22
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 23
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 24
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 25
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
CS6304-Analog & Digital Communication UNIT-2 Page 26
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
Quadrature Amplitude Modulation (QAM)
Overview
This tutorial is part of the National Instruments Measurement Fundamentals series. Each tutorial in this series teaches you a specific topic of common measurement applications byexplaining the theory and giving practical examples. This tutorial covers an introduction to RF, wireless, and high-frequency signals and systems.
For the complete list of tutorials, return to the NI Measurement Fundamentals main page, or formore RF tutorials, refer to the NI RF Fundamentals main subpage. For more information about
National Instruments RF products, visit www.ni.com/rf.
A variety of communication protocols implement quadrature amplitude modulation (QAM). Current
protocols such as 802.11b wireless Ethernet (Wi-Fi) and digital video broadcast (DVB), for
example, both utilize 64-QAM modulation. In addition, emerging wireless technologies such as
Worldwide Interoperability for Microwave Access (WiMAX), 802.11n, and HSDPA/HSUPA (a new
cellular data standard) will implement QAM as well. Thus, understanding QAM is important
because of its widespread use in current and emerging technologies.
QAM involves sending digital information by periodically adjusting the phase and amplitude of a sinusoidal electromagnetic wave. Each combination of phase and amplitude is called a symbol and represents a digital bitstream. This tutorial first covers the hardware implementation requiredto constantly adjust the phase and amplitude of a carrier wave. The tutorial also discusses the binary value associated with each symbol.
Hardware Implementation
Quadrature amplitude modulation (QAM) requires changing the phase and amplitude of a carriersine wave. One of the easiest ways to implement QAM with hardware is to generate and mix twosine waves that are 90 degrees out of phase with one another. Adjusting only the amplitude of either signal can affect the phase and amplitude of the resulting mixed signal.
These two carrier waves represent the in-phase (I) and quadrature-phase (Q) components of our
signal. Individually each of these signals can be represented as:
I = A cos(φ) and Q = A sin(φ).
Note that the I and Q components are represented as cosine and sine because the two signals are90 degrees out of phase with one another. Using the two identities above and the following
trigonometric identity
cos(α + β) = cos(α)cos(β) – sin(α)sin(β),
CS6304-Analog & Digital Communication UNIT-2 Page 27
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
rewrite a carrier wave A cos(2πfct + φ) as
A cos(2πfct + φ) = I cos(2πfct) – Q sin(2πfct).
As the equation above illustrates, the resulting identity is a periodic signal whose phase can be adjusted by changing the amplitude of I and Q. Thus, it is possible to perform digital modulation
on a carrier signal by adjusting the amplitude of the two mixed signals.
Figure 1 shows a block diagram of the hardware required to generate the intermediate frequency(IF) signal. The ―Quadrature Modulator block shows how the I and Q signals are mixed with ‖the local oscillator (LO) signal before being mixed together. The two LOs are exactly 90 degreesout of phase with one another.
Hardware Used to Generate the IF Signal
The next section discusses exactly how the I and Q components are used to represent actual
digital data. To do this, the following section details the relationship between the QAM symbolmap and the actual real-world signal.
QAM Symbol Map
As stated previously, QAM involves sending digital information by periodically adjusting the phase and amplitude of a sinusoidal electromagnetic wave. Four-QAM uses four combinations ofphase and amplitude. Moreover, each combination is assigned a 2-bit digital pattern. For example, suppose you want to generate the bitstream (1,0,0,1,1,1). Because each symbol has a unique 2-bit digital pattern, these bits are grouped in two’s so that they can be mapped to the corresponding symbols. In our example, the original bitstream (1,0,0,1,1,1) is grouped into the three symbols (10,01,11).
In the following figure, 4-QAM consists of four unique combinations of phase and amplitude. These combinations—called symbols—are shown as the white dots on the constellation plot in Figure 2. The red lines represent the phase and amplitude transitions from one symbol to another.Labeled on the constellation plot is the digital bit pattern that each symbol represents. Thus, a digital bit pattern can be sent over a carrier signal by generating unique combinations of phase and amplitude.
CS6304-Analog & Digital Communication UNIT-2 Page 28
Getmynotes.com
Sri Vidya College of Engineering & Technology, Virudhunagar Course Material (Lecture Notes)
QAM Symbol Map
How do these digital bit patterns correspond to I/Q data? Figure 3 shows both the I/Q data (top)and the 2-bit digital pattern (in a constellation plot, bottom) relating to 4-QAM. The black dashed line in the top graphic corresponds to the black square marker in the bottom graphic, so you can follow the phase and amplitude changes as the I/Q parameters also change.
QAM Baseband I/Q Data (bottom) 4-QAM Constellation Plot
CS6304-Analog & Digital Communication UNIT-2 Page 29
Getmynotes.com
Getmynotes.com Course Material (Lecture Notes)
The constellation plot in Figure 2 shows the symbol map of 4-QAM with each possible phase( and amplitude (A) of a carrier signal in polar coordinate form. Notice how in the bottom
graphic of Figure 3 the square marker passes over each symbol at least once.
While it is possible to send up to two bits per symbol when using 4-QAM modulation, it is also possible to send data at even higher rates by increasing the number of symbols in our symbol map. By convention, the number of symbols in a symbol map is called the symbol map ―M ‖and is considered the ―M-ary of the modulation scheme. In other words, 4-QAM has an M-ary‖of four and 256-QAM has an M-ary of 256. Moreover, the number of bits that can be representedby a symbol has a logarithmic relationship to the M-ary. For example, we know that two bits canbe represented by each symbol in 4-QAM. While this makes sense intuitively, it is defined by the
equation bits per symbol = log2 (M).
Using this equation, each symbol in 256-QAM can be used to represent an 8-bit digital pattern
(log2 (256) = 8). Because the M-ary of a QAM modulation scheme affects the number of bits per symbol, the M-ary has a significant affect on the actual data transmission rate.
Bandwidth Efficiency refers to the information rate that can be transmitted over
a given bandwidth in a specific communication system
QAM bits per symbol
The advantage of using QAM is that it is a higher order form of modulation and as a result it isable to carry more bits of information per symbol. By selecting a higher order format of QAM,the data rate of a link can be increased.
The table below gives a summary of the bit rates of different forms of QAM and PSK.
MODULATION BITS PER SYMBOL SYMBOL RATEBPSK 1 1 x bit rate
QPSK 2 1/2 bit rate
8PSK 3 1/3 bit rate
16QAM 4 1/4 bit rate
32QAM 5 1/5 bit rate
64QAM 6 1/6 bit rate
CS6304-Analog & Digital Communication UNIT-2 Page 30
Getmynotes.com
Getmynotes.com Course Material (Lecture Notes)
Comparison of various Digital Communication System (ASK – FSK – PSK – QAM).
CS6304-Analog & Digital Communication UNIT-2 Page 31
Getmynotes.com