NIRPC Environmental Management Policy Committee February 7, 2013
Unified Trail Wayfinding Guide - NIRPC
Transcript of Unified Trail Wayfinding Guide - NIRPC
Alta Planning + Design
NIRPC Unified Trail
Wayfinding
800 S Broadway, 2nd Floor Front
Baltimore, MD 21231
ph: 443.218.8165
August 2016
The purpose of these drawings is to illustrate design intent. Drawings are not for
construction. Written dimensions on these drawings have precedence over scaled
dimensions.
The further development and engineering of these drawings shall be submitted as
shop drawings to the Project Owner. Contractors shall verify and be responsible
for all final quality, dimensions, materials and conditions on the job.
Project owner shall be notified of any variations from the dimensions and
conditions shown by these drawings prior to the execution of any work, including
changes to graphic designs or typography.
Drawing scale shown on plans is for full size plans only. Alta shall not be
responsible for scale discrepancies caused by reduced or enlarged drawings.
Graphic Standards
System Overview
Welcome Sign
Vehicular Trailhead
Map Kiosk
Pedestrian Directional Sign
Pedestrian Regulatory Sign
Mile Marker
DESIGNINTENT
Northwestern Indiana
Regional Planning Commision (NIRPC)
6100 Southport Road
Portage, Indiana 46368
Contact: Mitch Barloga, AICP
Phone: 219.763.6060 x133
Fax: 219.762.1653
DRAWINGS
2
3
4
5
6
7
8
9
TABLE OF CONTENTS
Northwest Indiana Greenways
& Blueways Logo
Praire Grass Silhouette
Destination Travel Distance & TimesTypical Arrow
Calumet Trail LogoDunes Kankakee Trail Logo Gary Green Link Logo
Chesapeake and Ohio Greenway Logo
American Discovery Trail Logo The Marquette Greenway Logo Oak Savannah Trail Logo
Prarie Duneland Trail LogoVeterans Memorial Parkway Logo
Contractor is responsible for
matching all colors and materials
as specified and are required to
provide color and material sample
to the Project Owner for approval.
All painted surfaces to receive UV
and Anti-Graffitti coating. All
retroreflective material to receive
UV/Anti-Graffiti overlaminate, or
owner approved equal.
No substitute typefaces will be
accepted. Set kerning tracks to
visually approximate sign
drawings. Kerning shown may
vary from exact kerning used to
create sign drawings. Refer to
specific applications for type sizes
and leading requirements.
MATERIALS PALETTE
Contractor shall be responsible for supplying samples for all colors and materials within the palette.
White - ReflectiveBlack Green
White
Color:
3M 3930 High Intensity Retroreflective
Materials:
TYPOGRAPHY
Fabricator is responsible for acquiring project related fonts.
Highway Gothic
Highway Gothic Wide
Aa Bb Cc Dd Ee Ff Gg Hh Ii Jj Kk Ll Mm Nn Oo Pp Qq Rr Ss Tt Uu Vv Ww Xx Yy Zz 1234567890
ARTWORK
All artwork illustrated on this page shall be provided by Project Owner as electronic vector art.
Color match: CMYK (46%, 0%, 85%, 0%)
Matthews Paint
White
WhitePantone: 425 C
Matthews Paint
Graphic Standards
2
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
Aa Bb Cc Dd Ee Ff Gg Hh Ii Jj Kk Ll Mm Nn Oo Pp Qq Rr Ss Tt Uu Vv Ww Xx Yy Zz 1234567890
WrB GW StoneS
Process:
Surface painted, with Matthews
Polyurethane Clear Coat Protectant
Surface painted, with Matthews
Polyurethane Clear Coat Protectant
Surface painted, with Matthews
Polyurethane Clear Coat Protectant
Matthews Paint
Blue
Color match: CMYK (53%, 1%, 27%, 0%)
Matthews Paint
B
Surface painted, with Matthews
Polyurethane Clear Coat Protectant
Dark Green
Color match: CMYK (65%, 23%, 100%, 6%)
Matthews Paint
G
Surface painted, with Matthews
Polyurethane Clear Coat Protectant
Dark Blue
Color match: CMYK (86%, 34%, 56%, 14%)
Matthews Paint
B
Surface painted, with Matthews
Polyurethane Clear Coat Protectant
C
I
T
Y
L
O
G
O
NAME2
TRAIL
HEAD
NAME2
TRAIL
HEAD
C
I
T
Y
L
O
G
O
C
I
T
Y
L
O
G
O
City of Name
C
I
T
Y
L
O
G
O
Welcome to
City Name
Cross-street
Name
C
I
T
Y
L
O
G
O
WELCOME SIGN VEHICULAR
TRAILHEAD
MAP KIOSK PEDESTRIAN
DIRECTIONAL
PEDESTRIAN
REGULATORY
MILE MARKER
WELCOME TO
CITY NAME
WELCOME TO
CITY NAME
NAME1
NAME1
System Overview
3
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
C
L
5'
4'-6" 5"
1'-4"
2'
10 1/2"
5'-6"
4"
Front Elevation
1
Scale: 3/4" = 1'-0"
Side Elevation
2
Scale: 3/4" = 1'-0"
1'
10"
2" typ
1'
Sign Layout
1. LIMESTONE SIGN
4'-6" L x 2'-4" W x 5" thick
MATERIAL: Indiana limestone
ASTM C568, Type II, Medium density limstone
2. STEEL HEADER
Structural steel H beam, W 6 X15 lb (5.99" x
.230" web x 5.99"). 1/2" fillet on all corners
3. SUPPORT POST
Square A500 steel tube, 4 x 4 x 3/8" wall.
Embedded into monument wall and welded to
steel header
4. LIMESTONE CAP
Smooth top and bottom, rock face sides.
SIZE: 5'-4" L x 1'-8" W x 4" H
5. MONUMENT WALL
SIZE: 5-0" L x 1'-4" W x 1'-8" H
Limestone natural stone veneer, depth 1-1/4"
nominal (3/4" to 1-1/2"), color to match sign
FABRICATION: Standard masonary
construction
6. LETTERING
1/2" thick aluminum letters, pin-mounted 1/2"
from face of sign
7. GREENWAYS & BLUEWAYS LOGO
MATERIAL: 8" dia x 1/4" thick aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: Pin mounted
GRAPHICS/TEXT: digitally printed
8. TRAIL LOGO
MATERIAL: 12" dia x 1/4" thick aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: Pin mounted
GRAPHICS/TEXT: digitally printed
9. CITY LOGO
MATERIAL: 8" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: Pin mounted
GRAPHICS/TEXT: digitally printed
10. CONCRETE FOOTING
Concrete footing to engineer's specifications
11. ENGRAVING
Sandblasted 'Prairie Grass' silhouette
EQ EQ
5"
1'-8"
C
I
T
Y
L
O
G
O
2" typ
EQ EQ
2'-4"
5'-4"
C
L
1' 1'
Drill & epoxy
3
-
Detail - Section
3
Scale: 3/4" = 1'-0"
C
L
1'
1'
4
5
2
3
1
Type: Highway Gothic,
4" high
Type: Highway Gothic,
6" high
9
6
1
2
2
3
87
4" x 6" steel plate
welded to lower half
of H-beam, typ both ends
(shown larger for clarity)
3
Spacer material
Steel dowels, weld to
H beam, spacing, length
& size per engineer
10
11
B
B
#
WELCOME TO
CITY NAME
WELCOME TO
CITY NAME
5"
Welcome Sign
4
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
KEY NOTES
8'
1'
2'-8"
2'
8"
NAME1
NAME2
TRAIL
HEAD
Side Elevation
2
Scale: 3/4" = 1'-0"
Rear Elevation
3
Scale: 3/4" = 1'-0"
Front Elevation
1
Scale: 3/4" = 1'-0"
10"
3'-10"
EQ EQ
C
I
T
Y
L
O
G
O
1. ALUMINUM SLEEVE & FRAME
MATERIAL: 1/8" thick aluminum
Fabricated alumimum sheet sign face and
back, fully welded and fabricated sides with all
edges and corners neatly finished
FRAME: Fabricated aluminum channel internal
structure to engineer's specification. Frame to
be set inside perimeter of sign sleeve
2. TRAIL LOGO
MATERIAL: 12" dia x 1/4" thick aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
3. RAISED LETTERING
MATERIAL: 1/2" thick aluminum
EDGES: Routed, finished smooth
FASTENER: adhesive
4. GREENWAYS & BLUEWAYS LOGO
MATERIAL: 8" dia x 1/4" thick aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
5. CITY LOGO
MATERIAL: 8" dia x 1/4" thick aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
6. DIGITAL PRINT
Digitally printed 'Praire Grass' silhouette and
stone texture (not shown)
7. CONCRETE FOOTING
Concrete footing to engineer's specifications.
Conceal hold down bolts within sign structure
C
L
6"
6"
6"
4"
NAME1
NAME2
TRAIL
HEAD
C
I
T
Y
L
O
G
O
7'-8"
6
2
4
Type: Highway Gothic,
4" high
7
1
3
5
W
S
Vehicular Trailhead Sign
5
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
KEY NOTES
C
I
T
Y
L
O
G
O
7'
8"
2'-8"
1'-10"
4'
Front Elevation
1
Scale: 3/4" = 1'-0"
Side Elevation
2
Scale: 3/4" = 1'-0"
Rear Elevation
3
Scale: 3/4" = 1'-0"
Location panel
(optional)
EQ EQ
3" margin on both sides
5"
2"
2"
3"
1. TRAIL LOGO
MATERIAL: 12" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
2. GREENWAYS & BLUEWAYS LOGO
MATERIAL: 6" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
3. CITY LOGO
MATERIAL: 6" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
4. ALUMINUM SLEEVE & FRAME
MATERIAL: 1/8" thick aluminum
Fabricated alumimum sheet sign face and
back, fully welded and fabricated sides with all
edges and corners neatly finished
FRAME: Fabricated aluminum channel internal
structure to engineer's specification. Frame to
be set inside perimeter of sign sleeve
5. MAP PANEL:
MATERIAL: Non-glare clear acrylic panel, high
pressure laminate map panel.
ARTWORK: Directory map shown for
reference only. Map with all associated texts
and pictograms to be provided in digital format.
FASTENER: (6) six stainless steel Ø1-1/2" x 1"
length stand-offs, tamper-proof
6. LOCATION PANEL
MATERIAL: 1/8" thick aluminum
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
7. DIGITAL PRINT
Digitally printed 'Praire Grass' silhouette and
stone texture (not shown)
8. CONCRETE FOOTING
Concrete footing to engineer's specifications.
Conceal hold down bolts within sign structure
9. LOGO TOP PANEL
MATERIAL: 1/8" thick aluminum
FASTENER: welded
C
I
T
Y
L
O
G
O
City of Name
4"
4"
1"
6'-8"
10"
7
6
5
3
BOTTOM ZONE:
Rules & Regulations
TOP ZONE:
Trail map
8
2
5
1
4
9
Information
(optional)
S
S
G
Map Kiosk
6
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
KEY NOTES
7'
8"
1'-10"
Front Elevation
1
Scale: 3/4" = 1'-0"
Right Side Elevation
2
Scale: 3/4" = 1'-0"
Rear Elevation
3
Scale: 3/4" = 1'-0"
Destination panel,
total of 3
Location Panel
(optional)
Welcome Panel
(optional)
10"
2"
10"
2"
10"
2"
6"
4"
2'-2"
2" 2"
6"
2"
C
I
T
Y
L
O
G
O
1'-8"
C
I
T
Y
L
O
G
O
Welcome to
City Name
Cross-street
Name
Welcome to
City Name
Cross-street
Name
4"
6'-8"
2
3
4
8
9
1
7
1. ALUMINUM SLEEVE & FRAME
MATERIAL: 1/8" thick aluminum
Fabricated alumimum sheet sign face and
back, fully welded and fabricated sides with all
edges and corners neatly finished
FRAME: Fabricated aluminum channel internal
structure to engineer's specification. Frame to
be set inside perimeter of sign sleeve
2. DESTINATION PANEL
Panel wraps around sleeve
MATERIAL: 1/8" thick aluminum
FABRICATION PROCESS: Router cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
3. LOCATION PANEL
Panel wraps around sleeve
MATERIAL: 1/8" thick aluminum
FABRICATION PROCESS: Router cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
4. WELCOME PANEL
Panel wraps around sleeve
MATERIAL: 1/8" thick aluminum
FABRICATION PROCESS: Router cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
5. GREENWAYS & BLUEWAYS LOGO
MATERIAL: 4" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
6. TRAIL LOGO
MATERIAL: 4" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: screen printed
7. CITY LOGO
MATERIAL: 4" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
8. DIGITAL PRINT
Digitally printed 'Praire Grass' silhouette and
stone texture (not shown)
9. CONCRETE FOOTING
Concrete footing to engineer's specifications.
Conceal hold down bolts within sign structure
65
G
G
B
S
Note: Left side similiar but w/o
signs wrapped around
1'-8"
10"
Destination Panel Layout
Type: Highway Gothic Wide,
1-1/2" high
3/4"
1 3/4"
4 3/4"
2 1/4"
5 3/4"
C
L
Type: Highway Gothic,
3/4" high
2 1/2"
Pedestrian Directional Sign
7
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
KEY NOTES
C
I
T
Y
L
O
G
O
C
I
T
Y
L
O
G
O
1. SIGN PANEL
MATERIAL: 1/8" thick aluminum
FABRICATION PROCESS: Router cut
EDGES: Routed, finished smooth
FASTENER: adhesive
GRAPHICS/TEXT: digitally printed
2. GREENWAYS & BLUEWAYS LOGO
MATERIAL: 8" dia x 1/4" thk. aluminum
FABRICATION PROCESS: Router Cut
EDGES: Routed, finished smooth
FASTENER: welded to post cap
3. WOOD POST
MATERIAL: 4" x 4" pressure treated wood
INSTALLATION: 30" min. bury or surface
mount per engineer's specifications
4. POST BRACKET
MATERIAL: steel, design by engineer
FABRICATION PROCESS: welded
FASTENER: Per engineer's specifications
5. POST CAP
MATERIAL: 1/8" thick aluminum
Fabricated alumimum sheet top, fully welded
and fabricated sides with all edges and corners
neatly finished
FASTENER: mechanically fasten to wood post
6. SIGN FASTENERS
Per engineer's specifications
Front Elevation
2
Scale: 3/4" = 1'-0"
2'-10"
4'-10"
6"
Side Elevation
3
Scale: 3/4" = 1'-0"
5'-6" post height
Sign Layout
1
Scale: 1 1/2" = 1'-0"
2'
1'-2"
1 1/2" m
in.
R
1
1
/
2
"
,
t
y
p
1 1/2" m
in.
C
L
1
2
3
6
4
1
5
3/8" Ø hole, typ of 2
5 1/2"
8"
Typical sign, varies
#
B
B
Pedestrian Regulatory Sign
8
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
KEY NOTES
2'-10"
10"
3
-
Front Elevation
1
Scale: 3/4" = 1'-0"
C
L
Detail
3
Scale: 1 1/2" = 1'-0"
8"
Side Elevation
2
Scale: 3/4" = 1'-0"
3 1/2"
4"
7"
2'-6"
1
3
Type: Highway Gothic,
2" high
2
5
4
1. ALUMINUM SLEEVE & FRAME
MATERIAL: 1/8" thick aluminum
Fabricated alumimum sheet sign face and
back, fully welded and fabricated sides with all
edges and corners neatly finished
FRAME: Fabricated aluminum channel internal
structure to engineer's specification. Frame to
be set inside perimeter of sign sleeve
2. DIGITAL PRINT
Digitally printed 'Praire Grass' silhouette and
stone texture (not shown)
3. CONCRETE FOOTING
Concrete footing to engineer's specifications.
Conceal hold down bolts within sign structure
4. CUT-OUT TEXT
Text and numbers cut out of aluminum sleeve.
EDGES: Routed, finished smooth
5. BACK PANEL
MATERIAL: 1/8" thick aluminum
FASTENER: welded to sleeve
Sign is double-sided
W
S
Mile Marker Post
9
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
KEY NOTES
8"
1. GREENWAYS & BLUEWAYS LOGO
MATERIAL: 1/4" thick aluminum
FABRICATION PROCESS: router cut
EDGES: routed, finished smooth
FASTENER: per engineer's specifications
GRAPHICS/TEXT: digitally printed
2. PAVEMENT MARKING
MATERIAL: Preformed thermoplastic
3. UNDERPASS SIGN
Final size of sign dependant on sign placement
and at the discretion of the engineer to ensure
legibility for trail users.
MATERIAL:
1
4
" thick aluminum
FABRICATION PROCESS: router cut
EDGES: routed, finished smooth
FASTENER: per engineer's specifications
GRAPHICS/TEXT: digitally printed
4. DIGITAL PRINT
Digitally printed 'Prairie Grass' silhouette and
stone texture (not shown)
3/8" Ø hole, typ of 2
Mile
2
1'-6 3/4"
1'
8"
Type: Highway Gothic Wide,
2" high
1" White Border
1"
Sign Blaze
1
Scale: 1 1/2" = 1'-0"
3/4"
1
Pavement Marking
2
Scale: 1 1/2" = 1'-0"
Trail Underpass Sign
3
Scale: 1 1/2" = 1'-0"
2
Street Name
3'
1'
8"
3/8" Ø hole, typ of 6
3
3"
2"
6"
Front View Side View
Mechanical wall
fasteners to be
specified by installer
Manufacturer to field verify all
wall conditions and specify
the appropriate mechanical
fastener
4
Mile Marker Post
10
NIRPC Unified Trail Wayfinding
Northwestern Indiana
Regional Planning Commission
· These drawings are intended to illustrate
design intent only and are not for
construction. All final engineering and
conditions of the project are the
responsibility of the fabricator. Shop
drawings by the fabricator must be
submitted for approval, prior to proceeding
with fabrication.
· The quality of fit and finish on the final
product must meet or exceed the
requirements of these design intent
documents. Any variations to design,
materials, or fabrication methods must be
approved by the Owner or Representive.
· Welds: All welds shall be ground smooth,
paint all seams.
· Hardware: All exposed hardware shall be
tamper proof fasteners.
· All exposed edges painted to match
adjacent face.
· Colors shown are for reference only and
are subject to the limitations of the printing
process. Refer to referenced color systems
contained within these drawings for actual
specifications.
· Scaled examples shown are for reference
only, and do not necessarily reflect actual
site conditions. Detailed site surveys are
required prior to fabrication and installation.
· Messages shown in these drawings are for
general reference only. Refer to message
schedules for actual required messages.
GENERAL NOTES
PROJECT
CLIENT
SHEET NUMBER
DOCUMENT ISSUE
08 August 2016
SHEET TITLE
Alta Planning + Design
800 S Broadway,
Baltimore, MD 21231
ph: 443.218.8165
KEY NOTES