UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT...

29
UNICAT Individual Expedition vehicle IN57p MAN TGM 4x4 Chassis: MAN TGM 4x4, 250 kW / 340 hp, EURO 5 Seats: 2 Beds: 1 Body: UNICAT IN57p, length 5,7 m (224,4“) Seating capacity: 2-4 Permanent beds: 2 UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 1 29

Transcript of UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT...

Page 1: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Individual Expedition vehicle IN57p MAN TGM 4x4

Chassis: MAN TGM 4x4, 250 kW / 340 hp, EURO 5 Seats: 2 Beds: 1 Body: UNICAT IN57p, length 5,7 m (224,4“) Seating capacity: 2-4 Permanent beds: 2

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 1 29

Page 2: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Chassis

▪ MAN TGM 18.340 4x4 ▪ L-cab ▪ Wheel base 4500 mm (177.1“) ▪ Engine Performance 250 kW / 340 hp, Euro 5 ▪ ZF 12-speed Tip-Matic-Gearbox ▪ Cruise control ▪ Transfer case with off-road reduction ▪ All wheel drive with central differential lock ▪ Differential lock in front and rear axle ▪ Parabolic leaf springs ▪ Stabilizers on front and rear axle ▪ Drum brakes with ABS ▪ Tires 14.00 R 20 tubeless ▪ 1 x spare wheel 14.00 R 20 tubeless ▪ Fuel tank capacity: 600 liters diesel (158.5 US gallon) ▪ Fuel prefilter with water separator, heated ▪ Underride protection plates under the fuel tanks ▪ Aluminium roof rack with branch guard ▪ 2 x LED high beam headlamp mounted on the front of the roof rack,

each 167 W, 12970 lm ▪ 2 x LED low beam headlamp mounted on the front of the roof rack

each 88 W, 7091 lm ▪ 2 x LED working lights mounted sideways on the roof rack, each 17 W, 700 lm ▪ Headlight protector ▪ Reading lights for driver and co-driver

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 2 29

Page 3: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

▪ Truck horns ▪ Access to drivers cab with isolated panel ▪ Rear under ride guard, manually retractable ▪ Additional safety locks for drivers cab, keyed alike with the body ▪ 2 air suspended seats, heated and ventilated ▪ 2 spare seats covered with ALCANTARA, convertible to a lying surface ▪ All around curtains ▪ Sun visor ▪ Electric windows ▪ Integrated air conditioning ▪ Auxiliary heater with hight adjustment ▪ Rearview camera ▪ Vehicle immobilizer ▪ Central door locks ▪ ETA automatic cutout ▪ Garmin satellite navigation (GPS) ▪ CB radio ▪ USB charging sockets ▪ 230 V sockets ▪ Radio with CD player / USB port / Bluetooth / iPod - iPhone integration ▪ I-Pad mount ▪ Clothesline, extendable

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 3 29

Page 4: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Body

Outer dimensions of the cabin ▪ Length 5700 mm (224.4“), width 2480 mm (97.6“), height 2105 mm (82.8“)

Inner dimensions of the cabin ▪ Length 5580 mm (219.6“), width 2360 mm (92.9“), height 1950 mm (76.7“)

Frame assembly ▪ 3-point kinematic attachment with main and flex mounts

for stress-free body coupling to the torsion elastic chassis frame

Body unit construction ▪ Self supporting UNICAT sandwich plate panels of fiberglass composite ▪ Wall thickness 60 mm (2.36") with polyurethane foam insulation,

3 mm (0.12") FRP outer surface, 2 mm (0.08") FRP inner surface, insulation rating 0.44 W/m2 K (0.078 Btu/ft2 hr °F)

▪ Cold bridge free glued with FRP profiles ▪ Bottom panel with integrated welded steel frame and surfaces of FRP ▪ Additional insulation of the floor

Access to driver cab ▪ Highly flexible waterproof bellows coupling ▪ Panel to close passage way

Entrance door and storage compartment doors ▪ Entrance door and storage compartment doors constructed of fiberglass

composite panels ▪ Thickness of doors 60 mm (2.36“) ▪ Double sealed doors with heavy duty locks and seal compression ▪ Anti-theft stainless steel hinges ▪ 6-point locking door with closing trap and hook, additional retractable bolts at

top and bottom of the entrance door ▪ Safety cylinder locks ▪ Safety cylinder locks all keyed alike ▪ Central locking with remote control ▪ Electric mosquito net for entrance door

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 4 29

Page 5: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Windows ▪ Scratch-resistant, burglar-proof hinged UNICAT-windows ▪ Double insulated thermal window glass ▪ Double sealing with combined hollow profile and lip seal ▪ Anti-theft stainless steel hinges ▪ Window display and lock made of stainless steel ▪ Blinds with sun protection and mosquito net ▪ Fixed window in front with sun protection blinds

Roof hatch ▪ Scratch-resistant, burglar-proof boat roof hatch with mosquito net

in the shower ▪ 12 mm (0,47“) acrylic glass ▪ Protected built-in hollow profile gasket

Stairway ▪ Integrated, 3-step staircase with storage compartments ▪ Additional stairs 2-stage, electrically extendable, mounted under the staircase

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 5 29

Page 6: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Interior Layout

Seating unit ▪ U-shaped seating area for 2-4 persons ▪ Rotatable and electrically lowered table ▪ Table extension ▪ Seating unit converts to additional bed: 1300 mm (51.1“) x 2000 mm (78.7“)

Beds ▪ Double bed with suspension, ventilation, heating and comfortable mattress in

the rear ▪ Size: 1400 mm (55.1“) x 2000 mm (78.7“) ▪ Dividing walls and curtain at the seating group

Sanitary room ▪ CORIAN washbasin with vanity unit and integrated washbasin ▪ Single lever faucet for hot and cold water ▪ Mirror over the vanity ▪ Overhead cupboard next to the washbasin ▪ Wall cupboard above the toilet ▪ Large wall mirror ▪ Porcelain toilet ▪ Teak floor

Shower room ▪ Separate shower and toilet room with glass door to separate to the living room

or to the shower room ▪ Towel radiator ▪ Mosaic tile floor with slope and gutter

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 6 29

Page 7: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Kitchen ▪ BLANCO-DURINOX stainless steel countertop with integrated sink and

flush mounting of the hob ▪ Single lever faucet for hot and cold water ▪ Soap dispenser ▪ Miele 2 zone induction cooker ▪ Miele oven with microwave ▪ Fridge-freezer, 160 liters (42.2 US gallon) cooling,

20 liters (5.2 US gallon) freezer ▪ Base cabinets with drawers on ball-bearing full extensions ▪ Shock-proof separation for tableware, cookware and kitchen appliances ▪ Drawer for cutlery with knife block ▪ Kitchen wall cabinets ▪ Integrated trash can

Storage ▪ Wardrobe in the bed area ▪ Overhead cupboards in bed area ▪ Overhead cupboards in the seating area ▪ Storage compartments by the seating unit ▪ Storage compartment under the bench to accommodate a cooler box ▪ Tall cabinet with shelves, lower area is for the washer-dryer ▪ Technical cabinet with drawer and wall shelf ▪ Bookshelf ▪ Teak storage box ▪ Entrance staircase with storage compartments ▪ Large outside storage compartment under the bed pedestal ▪ Aluminium exterior storage boxes ▪ Large storage boxes at the loading platform

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 7 29

Page 8: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Workmanship ▪ All furniture is built to the highest cabinetmaking standard,

made of wood core plywood with white surfaces and teak edges ▪ Heavy duty locks and hinges ▪ All drawers on ball bearings ▪ Surfaces white or teak with teak edges

Layout ▪ Teak floor ▪ Walls and ceiling are painted with multiple coats ▪ Upholstery made of ALCANTARA

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 8 29

Page 9: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Technical equipment

Electrical equipment ▪ Control panel for power management and monitoring of liquid levels ▪ Safety cutout, fault current breaker, battery main switch ▪ Own, independent power supply for the body ▪ 6 AGM batteries 24 V - 630 Ah, effectively useable energy 7,8 kWh ▪ Additional alternator with I-U charge controller, charging power 3,36 kW ▪ Uninterruptible power supply through inverter 230 V 50 Hz,

continuous output 3 kW, peak output 6 kW, charging power 1,7 kW ▪ International battery charger, 90-260 V (45-65 Hz), charging power 0,72 kW ▪ Solar system 1620 W with MPPT solar regulators ▪ Sockets for 12 V DC, 24 V DC, 230 V AC and USB charging sockets

Telemonitoring ▪ Body-batteries: Voltage, electricity, capacity, temperature, history ▪ Chassis-batteries: Voltage ▪ Solar system: Voltage, Yield ▪ Position

Generator ▪ Honda EU 20i, petrol powered mobile generator ▪ Performance: 1,6 kW / 2,0 kW ▪ Tank capacity 4.1 liters (1.0 US gallon)

Lightning ▪ LED lights in the living area, above the table, kitchen, bed, sanitary room

and shower ▪ LED gooseneck reading lights dimmable in the seating area and by the bed ▪ LED strips in the rear storage compartment ▪ LED working lights at the rear

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 9 29

Page 10: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Fresh water system ▪ 2 tanks for fresh water with 2 water pumps and filters ▪ Tank volume 640 liters (169.0 US gallons) freeze-proof fresh water tanks,

mounted inside the body ▪ All water installations are laid frost-proof in the heated indoor area ▪ 60 liter (15.8 US gallons) hot water heat exchanger with electric heater ▪ City water connector ▪ Outside shower with warm and cold water ▪ Compressed air wintering of the water system

Wastewater system ▪ Wastewater tank capacity: 200 liters (52.8 US gallons), freeze-proof mounted

inside the body ▪ Pneumatic outlet valve, heated ▪ Discharge from the cab and body

Toilet system ▪ Sealand toilet with flushing ▪ Holding tank capacity: 115 liters (30.3 US gallons), freeze-proof mounted

inside the body ▪ Vacuum tank ventilation with activated carbon filter ▪ Pneumatic outlet valve, heated ▪ Discharge from the cab and body

Heating system ▪ Hot water central heating (5,0 kW) for diesel operation with height adjustment ▪ Heat exchanger to use the engine waste heat to heat the cabin and to generate

hot water while driving ▪ Extension of the central heating system for heating the cab and the engine ▪ Radiator in the seating area ▪ Towel radiator in the shower ▪ Bed heating under the mattress ▪ Antifrost system

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 10 29

Page 11: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

Air conditioning ▪ Roof air conditioner with heating element, mounted above the seating area ▪ Cooling capacity 2,7 kW, Electric power consumption 1,4 kW ▪ Operation via batteries, generator and shore power

HIFI / TV / Video ▪ Radio with CD player / USB port / Bluetooth / iPod - iPhone integration

in the seating area ▪ Bose sound system ▪ UMTS wireless router

Others ▪ Loading platform for 1 spare wheel and 2 large storage boxes ▪ Bike carrier for 2 bicycles integrated in a large storage box ▪ Miele washer dryer ▪ Folding worktop in the entrance area ▪ Built-in cool box under the seating unit, capacity 52 liters (13.7 US gallons) ▪ Weather station ▪ Awning 3200 mm (125.9“) x 2000 mm (78.7“) fixed with lashing points on the

side wall ▪ Lashing rails in the rear storage compartment

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 11 29

Page 12: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

General information

Dimensions ▪ Length 8245 mm (324.6“), width 2492 mm (98.1“), height 3682 mm (144.9“) ▪ Additional length spare wheel holder: 580 mm (22.8“)

Weights ▪ Curb weight including fresh water and fuel: 12.300 kg (27116 lbs) ▪ Gross vehicle weight rating: 13.900 kg (30644 lbs) ▪ Axle load distribution: 41% front axle, 59% rear axle

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 12 29

Page 13: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 13 29

Page 14: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 14 29

Page 15: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 15 29

Page 16: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 16 29

Page 17: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 17 29

Page 18: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 18 29

Page 19: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 19 29

Page 20: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 20 29

Page 21: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 21 29

Page 22: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 22 29

Page 23: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 23 29

Page 24: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 24 29

Page 25: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 25 29

Page 26: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 26 29

Page 27: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 27 29

Page 28: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 28 29

Page 29: UNICAT Individual Expedition vehicle IN57p MAN …Body unit construction Self supporting UNICAT sandwich plate panels of fiberglass composite Wall thickness 60 mm (2.36") with polyurethane

UNICAT Expedition Vehicle IN57p / MAN TGM 4x4 / 29 29