Understanding and Complying with the FDA
-
Upload
dentistryinfo -
Category
Documents
-
view
197 -
download
1
Transcript of Understanding and Complying with the FDA
![Page 1: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/1.jpg)
Understanding and Complying with the FDA
May 5, Western States Conference
Presented by Bennett Napier, CAE
![Page 2: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/2.jpg)
Federal Regulatory Agencies With Purview over Dental Laboratories
U.S. Dept. of Labor, Wage and Hour
![Page 3: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/3.jpg)
Why are dental laboratories being looked at now?
Increase in import trade Aging population Additionally focus on cosmetic dentistry Increased awareness of the dental
laboratory industry
![Page 4: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/4.jpg)
“The amount of dental devices now being imported into the United States is enormous.”
Bryan Benesch
Office of Compliance, FDA
![Page 5: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/5.jpg)
Why is the FDA the oversight agency?
The FDA is the federal agency that is responsible for ensuring the safety of materials and Medical Devices.
The FDA is responsible for ordering the recall of a medical device if it finds a reasonable probability that it would cause serious adverse health consequences or death.
Dental restorations are classified as Medical Devices.
![Page 6: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/6.jpg)
Understanding the FDA’s Objectives
For the most part, the FDA’s focus on domestic dental laboratories will center on these areas:
(1) Assuring that the materials used are FDA approved.
(2) Assuring that sufficient written procedures are in place to comply with the QS/GMP.
(3) Compliance with registration requirements.(4) Compliance with re-labeling requirements.
![Page 7: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/7.jpg)
Medical Devices
There are three types of medical devices:Class I – common dental restorations, such
as crowns, dentures and bridges would be classified here but currently are not classified.
Class II – sleep apnea/snoring devicesClass III – Body appendages (arms, legs)
prosthetic devices
![Page 8: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/8.jpg)
Import Trade Raises the Stakes
The Food and Drug Modernization Act of 1997 Section 417: any establishment engaged in
the manufacture, preparation, propagation, compounding, or processing of a drug or device imported into the United States must register with the FDA.
Effective: February 11, 2002
![Page 9: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/9.jpg)
Timeline for FDA activities relative to Dental Laboratories
In 2003 FDA released guidance document on:CAD/CAM dental restorationsSleep Apnea devicesClass II Devices, Dental Base Metal Alloys for Custom Manufactured Devices
In July 2003 a laboratory in Costa Rica was inspected by FDA for QS/GMP
![Page 10: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/10.jpg)
From 2004 to Date – FDA Activities
FDA has inspected at least 4 more laboratories.
Inspections are generally “for cause” which means that someone reported the laboratory and the inspection was not random.
Registered and unregistered laboratories have been inspected.
![Page 11: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/11.jpg)
REGISTRATION
How do you determine
if your laboratory is required
to register with the U.S.
Food and Drug Administration?
![Page 12: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/12.jpg)
Answer the following questions:
(1) Is your laboratory based outside the U.S.?
(2) Do you manufacture sleep apnea/snoring appliances?
( 3) Do you outsource any of your work to a foreign laboratory?
![Page 13: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/13.jpg)
If you answered “yes”:
A “yes” answer to any of the previous questions would trigger registration with the FDA.
![Page 14: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/14.jpg)
Is your laboratory based outside the U.S.?
As noted previously, because of the 1997 Food and Drug Modernization Act all foreign dental laboratories are required to register with the FDA.
In addition, foreign establishments must provide the FDA with the name of the U.S. agent representing their establishment. They must also continue to list the devices that they export to the U.S.
![Page 15: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/15.jpg)
Do you manufacture sleep apnea/snoring appliances?
The FDA classifies sleep apnea and snoring appliances as Class II Medical Devices.
All manufacturers of Class II Medical Devices are required to register with the FDA.
Registrants must provide a list of the products that they sell to FDA
![Page 16: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/16.jpg)
Are you an orthodontic laboratory or do you have an orthodontic department in your laboratory?
Some orthodontic appliances are classified as Class II Medical Devices and as such would require your laboratory to register with the FDA as a manufacturer of such devices.
Registrants must provide a list of the products that they sell to FDA
![Page 17: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/17.jpg)
Do you outsource any of your work to a
foreign laboratory?
If you outsource anything to a foreign establishment then you must register with the FDA as an initial importer/initial distributor.
Under 21 USC 360; 21 CFR 807, the definition of a manufacturer “includes repackaging or otherwise changing the container, wrapper or labeling in furtherance of distribution.”
Registrants must provide a list of the products that they sell to FDA
![Page 18: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/18.jpg)
Who is Exempt from Registration?
The FDA has the authority to exempt certain entities from registration.
The FDA has exempted “persons who dispense devices to the ultimate consumer or whose major responsibility is to render a service necessary to provide the customer with a device.”
This includes domestic dental laboratories under 21 CFR 807.65(I)
![Page 19: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/19.jpg)
Outsourcing
What do you need to know to comply with the FDA guidelines
![Page 20: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/20.jpg)
What to do if you outsource to a laboratory outside the U.S.:
Register with the FDA as an initial importer.
Require an affidavit from the laboratory that you outsource to stating that they only use materials that are FDA approved.
Make certain that the laboratory that you outsource to is registered with the FDA.
Comply with re-labeling requirements.
![Page 21: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/21.jpg)
What are the re-labeling requirements?
If a dental restoration was not made by your laboratory then it must be labeled as follows
“manufactured by (insert the name of the foreign laboratory)”
Or
“ distributed by (insert the name of your laboratory)”
![Page 22: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/22.jpg)
What to do if you outsource to another domestic laboratory?
Ask the laboratory if they outsource work to another foreign facility. If they do then require an affidavit from them stating that they and the laboratory that they outsource to are both registered with the FDA.
Require an affidavit from the laboratory that you outsource to stating that they comply with QS/GMP and only use materials that are FDA approved.
Comply with re-labeling requirements.
![Page 23: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/23.jpg)
“In essence, you are accountable for ensuring that if you’re going to use a
foreign firm that it meets all requirements.”
Harold “Wally” Pellerite
(former) Asst. to the Director
Office of Compliance, FDA
![Page 24: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/24.jpg)
Documentation assists in Compliance
Labeling/Pass Through Know where it’s Been Label where it’s Going
Identify Chain of Distribution Material used in device (and oversighting agencies) Device
MSDS Sheet/Identalloy Stickers (to meet US requirements)
State Requirements(i.e. Prop 65 in CA)
![Page 25: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/25.jpg)
Quality Systems/Good Manufacturing Practices
What is the criteria and how does your laboratory comply?
![Page 26: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/26.jpg)
Dental Laboratory Requirements and Responsibilities
All dental laboratories are legally responsible for ensuring compliance with pertinent regulations.
The FDA requires that all manufacturers of medical devices establish AND implement a quality system, tailored to the device that is manufactured.
This includes dental laboratories, regardless of whether or not you are required to register with the FDA.
![Page 27: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/27.jpg)
QS/GMP Standards
Design Controls Document Controls Purchasing Controls Identification/Traceability Production and Process
Controls Acceptance Activities Nonconforming Product
Corrective and Preventive Action
Labeling and Package Control
Handling, Storage, Distribution and Installation
Records Servicing Statistical Techniques
![Page 28: Understanding and Complying with the FDA](https://reader035.fdocuments.us/reader035/viewer/2022062300/558547a2d8b42a58788b532b/html5/thumbnails/28.jpg)
325 John Knox Rd, L103Tallahassee, FL 32303
Toll Free (800) 950-1150
Phone (850) 205-5626Fax (850) 222-0053
www.nadl.org www.nbccert.org
For More Information Please Contact: