Undercar Series · Includes 3-jaw puller and many types of joints. Slide hammer design for removing...
Transcript of Undercar Series · Includes 3-jaw puller and many types of joints. Slide hammer design for removing...
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1016 INNER CV JOINT PULLER
Fork type tool pulls CV joints with
hidden retaining rings & joints.
With this tool the axle assembly is
popped out of trans axle without
damage to transmission case or
inside roller bearing.
Open rate: 63mm
JTC-1020 HAND OPERATED FLUID EXTRACTOR
(10L)
Capacity: 10L
By manpower to push create vacuum
pressure for extracting fluid in any space.
Larger base to prevent falling while
operating.
Heat-resistance Temperature: 60℃
JTC-1024 PNEUMATIC OIL & LIQUID DISPENSER
6-liter, two in one extracts & pump
dispenser.
Specially designed for using on
narrow and difficult to reach space.
Fixing valve & safety cup for
automatic shut-off extract.
Content:
o 1.2m PU hose with
flexible rubber nozzle
o 1m nylon hose
Heat-resistance Temperature: 60℃
6 sets / 11kgs / 12kgs / 3.6'
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1025 PNEUMATIC BRAKE BLEEDER
Economically fast and easy, reduces labor cost.
Versatile-handles most standard and ABS brake system.
Clean-collects old brake fluid without spillage.
Quiet-integrated silencer for a quieter working environment.
Silicon suction assembly with universal rubber fitting.
Capacity: 2L
Working pressure: 70-170 psi
Air connection: 1/4"
Temperature range: -3˚ F ~ 140˚ F
12 sets / 15 kgs / 16 kgs / 6'
JTC-1026 BRAKE OIL FILLER
To fill break oil easily.
12 sets / 7 kgs / 8 kgs / 1.8'
JTC-1032 VACUUM OIL EXTRACTING MACHINE
& BRAKE BLEEDER (12L)
Capacity: 12L
Uses compressed air to create a
powerful vacuum to extract any
kinds of oil, gasoline, diesel, water,
and others anytime.
With limpid cup to check the flow
anytime.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1033 HAND OPERATED OIL PUMP
With reservoir capacity at 20L
Suitable for general lubricant and gear oil.
JTC-1034 AIR OPERATED GREASE PUMP
Uses air as power to stuck grease into
lubrication points.
Suitable for 00# ~ 2# grease.
Capacity: 20L
Air inlet pressure: 4 ~ 9kgs/cm
Pressure ratio: 45 : 1
Grease output pressure: 180 ~ 405kgs/cm
Deliver rate: 30cc / sec
JTC-1035 HYDRAULIC GEAR PULLER SET
For agriculture machine, automotive,
and industry use.
Hydraulic ram included for labor-
saving.
Material: SCM415 hardened 40˚ ~ 45˚
Packing: carrying case
1 set / 16 kgs / 17 kgs / 1.2'
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1036 OUTER TIE ROD REMOVER
Two adjustable jaws special designed for
removing.
Most models of outer tie rod.
Material: SCM420 Hardened 42˚
Packing: each / double blister
6 sets / 24 sets / 29 kgs / 30 kgs / 2.3'
JTC-1045 HAND OPERATED FLUID EXTRACTOR (6.5L)
Capacity: 6.5L
By manpower to push and create vacuum
pressure for extracting fluid in any space.
Special patented design for releasing the
pressure.
With extra tube storage
Heat-resistance temperature: 60℃
JTC-1050 PNEUMATIC & HAND OPERATED FLUID
EXTRACTOR
Capacity: 10L
Pneumatic & manual operation fluid extractor of
non-sparkle.
Three air outlets with check valve design for quick
& easy to exhaust the air from the extractor.
Easy to operate suitable for engine oil, gear oil,
break fluid, water.
Provide with new design decompression valve for
easy to release the negative pressure.
All parts are the same as JTC-1020
Heat-resistance temperature: 60℃
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1129 PITMAN ARM PULLER
Heavy duty forged alloy steel yoke.
Heated-treated center screw.
Remove tie rod ends and pitman
assemblies from many light trucks.
Opening size: 27mm
Pull travel: 45mm
JTC-1141 TWO SETS BEARING SEPARATOR KIT
Bearing separator 9000 and 9005 included.
Pull out the bearing with the H-type beam
and bolts.
JTC-1143 HYDRAULIC BEARING SEPARATOR PULLER KIT
Bearing separator 9025 inside.
Effort-saving with hydraulic screw.
Pullout the bearing with the H-type
beam and bolts.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1145 UNIVERSAL AXLES SLIDE HAMMER SET
Increased the cover range with the two axle
pullers.
Includes 3-jaw puller and many types of
joints.
Slide hammer design for removing hub and
repairing dent, etc.
JTC-1146 3-JAW INTERNAL & EXTERNAL PULLER SET
Size:
o Small internal puller: 15mm ~ 30mm
o Large internal puller: 30mm ~ 80mm
o External puller: 15mm ~ 80mm
Locking the nut to open 3-jaws and clip
the bearing, and then use the slide
hammer to pull out the bearing.
JTC-1212 CLIC-R COLLAR PLIERS
Special design for the CV ear-type
clamps.
For releasing and refitting reusable
hose clip.
For type-clic and clic-R.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1217 CV BOOT CLAMP TOOL
Easy to work in the narrow space.
Extra work on nose makes it compact.
A socket with ratchet is used to turn the
actuating screw for adjustment.
JTC-1230 ANGLE LOCATOR
Angle adjustable with the magnet attaching
on the alignment tool you working on.
Applicable with JTC-1840 or JTC-1002.
JTC-1247 BALL JOINT SEPARATOR (19mm)
Applicable on powerful structures.
Stand design to solve the space
problem.
Jaw open: 19mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1257 BALL JOINT SEPARATOR (23mm)
Jaws open: 23mm
Jaws deep: 25mm
Applicable: Audi, BMW, Citroen, Ford,
Mercedes, Opel, Peugeot, Renault, Rover,
Saab, Volvo, VW, Porsche, Pkw, etc.
JTC-1258 BALL JOINT SEPARATOR (28mm)
Jaws open: 28mm
Jaws deep: 25mm
Applicable: Audi, A4, A6, A8, VW, Passat after
97, etc.
JTC-1259 UNIVERSAL HUB PULLER
Readily adjustable sliding legs to pull
wheel hubs more quicker and easier
where the bolt circle does not exceed
7-1/2" (190.2mm)
Removers press-fit rear brake drums.
Striking handle and puller screw
included.
Special designed to use on most car
models.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1316 BALL JOINT EXTRACTORS (18mm)
For splitting track rod ends, anti-roll bar
mountings, ball joints, etc.
A: 18mm
B: 26mm
C: 38mm
JTC-1317 BALL JOINT EXTRACTORS (23mm)
For splitting track rod ends, anti-roll bar
mountings, ball joints, etc.
A: 23mm
B: 45mm
C: 47mm
JTC-1318 BALL JOINT EXTRACTORS (29mm)
For splitting track rod ends, anti-roll
bar mountings, ball joints, etc.
A: 29mm
B: 62mm
C: 62mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1319 BALL JOINT EXTRACTORS (40mm)
For splitting track rod ends, anti-roll bar
mountings, ball joints, etc.
A: 40mm
B: 62mm
C: 76mm
JTC-1320 BALL JOINT EXTRACTORS (46mm)
For splitting track rod ends, anti-roll bar
mountings, ball joints, etc.
A: 46mm
B: 76mm
C: 100mm
JTC-1323 UNVERASL STRUT NUT TOOL SET
The complete sizes for using on most
kinds of cars.
Contents: o 2 pcs central sockets 5, 10mm
o 9 pcs central sockets 4, 5.2, 6, 6.3, 7, 8, 9,
10, 12mm
o 4 pcs central sockets 5, 6, 7, 8mm
o 3 pcs central sockets 3, 3.5, 4mm
o 2 pcs central sockets T50, T60
o 1 pcs central sockets M12
o 4 pcs central sockets 8, 9, 10, 11mm
o 9 pcs central sockets 14, 16, 17, 18, 19,
21, 22, 24, 27mm
o 5 pcs central sockets 10.5, 12.5, 14, 14.5,
14.5 mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1329 CV BOOT HOSE CLAMP CUTTER
Designed easy to cut the stainless clamp.
Avoid hurting CV boot.
Width: Under 10mm
Thickness: Under 0.5mm ~ 0.7mm
JTC-1335 MANUAL BRAKE GAUGE SET
Special design to give customers an accurate
measurement of how much brake lining is
left without guess work.
Size:
Red: 2, 3mm – Bad
Yellow: 4, 5, 6mm – Dangerous
Blue: 8, 10, 12mm – Good
JTC-1336 THIN TYPE BALL-JOINT SEPARATOR
Special design for using on ball-joint
space limited.
The mini operation space: 6~7mm
Jaws open: 22mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1365 PANTAGON SOCKET BIT DRIVER (10mm)
For using on most vehicles fitting with
girdling brake systems.
Material: CR-V
Use with 1/2" Drive wrench
JTC-1401 HEAVY DUTY COIL SPRING COMPRESSOR
Hook engage spring which can be
compressed by turning hex nut.
Jaws capacity: 23mm ~ 280mm
Length: 280mm
JTC-1405 DISC BRAKE PISTON COMPRESSOR (4 PISTONS)
Special wider pusher design to use on
4-pistons vehicle.
Pusher width: 88mm
Applicable: BENZ, BMW, and 4
pistons vehicle
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1503 CV BOOT CLAMP INSTALLER
Installs low-profile clamps used to hold
CV boots on most FWD vehicles.
Ratchet-action and built-in cutter to
tighten the clamp quickly and properly.
JTC-1531 CV BOOT CLAMP PLIERS (EXTENSION)
For all ear-type clamps.
Application: AUDI, BMW, CHRYSLER, FORD,
GM, HONDA, MAZDA, MERCEDES, NISSAN,
OPEL / VAUXHALL, VW etc.
Designed to use with a 1/2" extension handle
or torque wrench.
JTC-1541 14-PCS WHEEL HUB RESURFACING KIT
To clean impurities in wheel case.
Contents:
o 1 1/2" grinding slice x 6pcs
o 2" grinding slice x 2pcs
o Special holder
Optional parts:
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1546 HOSE CLAMP PLIERS (ANGLE TYPE)
Designed with angle type to any space.
Swivel tip designed for re-fitting and
release.
For clic and clic-r type hose clamp.
JTC-1619 INNER CV JOINT PULLER
Fork type tool pulls CV joints with hidden
retaining rings and joints on 1986-current
Taurus / Sable.
With this tool the axle assembly is popped
out of trans-axle without damage to
transmission case or inside roller bearing.
Open rate: 48mm
JTC-1628 HUB SLIDE HAMMER PULLER
Pulls flange-type rear axles on most
late model passenger cars and light
trucks.
Designed to fit axles with bolts and
studs up to 9/16" diameter.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1708 BRAKE SPRING COMPRESSOR
BIG WINDOW designed for great visibility
during operation.
Allows fast and easy removal, and
replacement of brake shoe hold-down
springs.
JTC-1709 BRAKE SPRING TOOL
Hook the brake return spring, and screw-up
lock it for removal and installation.
A smart tool to service those breaks that
don’t use anchor pins.
JTC-1727 UNIVERSAL BALL JOINT SEPARATOR
Special design 2-stage operating suits
most cars and light trucks ball joints
in steering and suspension.
Offset level permits maximum jaw
opening in 30mm and 56mm.
Jaw open: 22mm
Applicable: Europe cars
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1733 TIRE CONSUMPTION GAUGE
Determine the average tire residual energy
between both positions which is
unconsumed part and also a right barometer
for safe driving.
To brake below tire thread 1.6mm / will bring
inferior effect.
Offers measurement of tire thread from 1 ~
30mm.
For automobile, below 1.6mm thread depth
is recommended for change.
For truck, below 2.4mm thread depth is
recommended for change
JTC-1833 CV BOOT CLAMP TOOL
Works on all CV joint with band-type boot
clamps.
This tool provides fast proper installation of
those clamps with ease.
This is a small, inexpensive functional tool for
use with 1/4" or 3/8" width band.
JTC-1836 INNER TIE ROD TOOL (8 PCS)
Works on inner tie rods with inaccessible
wrench flats.
Many inner tie rod end sockets do not
have a complete hex on the full length of
the socket. The rounded socket ends
prevent asses to the wrench flats.
Seven crows feet, sizes:
o 1-3/16", 1-1/4", 1-5/16", 1-7/16"
o 14mm, 17mm, and 33.6mm
The long socket then slips over the tie
rod end and connects to the crows foot.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1839 MULTI-PURPOSE INNER TIE ROD TOOL
The master tie rod tools easily replaces
inner tie rod ends without removing the
rack & pinion.
Capacity: 33 – 42mm
Patented.
JTC-1840 ALIGNMENT TOOLS
With 4 pcs alignment plates.
Hydraulic function.
Suited for most cars.
JTC-1843 BLIND HOLE BEARING PULLER SET
Open clamps by turning handle clockwise to
snug against the bearing for pulling-out
evenly without damaging parts.
Contents:
o Shaft: Slide hammer shaft – 390mm
long
o Hammer: 2.15 lb. (940g), 100mm L
o Clamps:
o 8~10mm (5/16"~13/32"); 10~12mm
(13/32"~15/32")
o 12~14mm (15/32"~9/19"); 15~17mm
(9/32"~11/16")
o 17~20mm (11/16"~25/32");
20~24mm (25/32"~15/16")
o 25~29mm (1"~1-1/8"); 30~32mm (1-
3/16"~1-1/4")
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1911 WHEEL WEIGHT TOOL
Easily removes and replaces wheel
weights, as well as cutting and crimping.
Made of heat strengthened steel.
Includes comfortable vinyl handle grips.
Self-open function spring on the handle
for easier operation.
JTC-1914 UNIVERSAL BALL JOINT PULLER
Special steel for removing the ball pivots on
steering.
Jaw open: 17mm
JTC-1915 UNIVERSAL BALL JOINT PULLER
Special steel for removing the ball
pivots on steering arms, steering tie
rocks, steering knuckles, etc.
Jaw open: 20mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1916 BALL JOINT SEPARATOR (22mm)
For splitting tack-rod ends, anti-roll bar
mountings, ball joints, etc.
A: 22mm
Max. B: 62mm
JTC-1920 CV BOOT CLAMP PLIERS
For ear type clamp.
Fits CV joint boots.
Installs perma-quick type clamps quickly and
easily.
Use for filter, cooling system and vacuum
lines.
JTC-1941 INTERCHANGEABLE-FORK SPRING COMPRESSOR
Spring compressors are multi-
application tools specifically.
Developed for modern macpherson
suspensions, using a range of 3 sets of
interchangeable monobloc forks.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1944 HEADLIGHT ADJUSTING AND BRAKE SPRING
HOOK
This tool made from heat treated alloy
steel is specially designed for removing
and installing hard-to-reach headlight
adjusting springs, OAL 6".
JTC-1950 STEERING WHEEL PULLER SET
Two specialty pullers in one set including one
flange type puller for removal of harmonic
balancers, timing gear, and other parts with
two or three tapped holes, and a steering
wheel, pulley, and flywheel puller.
JTC-1952 PITMAN ARM PULLER
Heavy duty forged alloy steel yoke.
Remove tie rod ends and pitman
assemblies from many light trucks.
Opening size: 33mm
Pull travel: 64mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-3430 TIRE SEAL (5 SHEETS / 25 PIECES)
Constituent: Butyl, Silk cotton
Contents: 25 strips of 5 pcs
100 / 19.2 / 20.5 / 1.96'
JTC-3431 TIRE SEAL TOOL SET
Contents:
JTC-3922
JTC-3923
JTC-3429
JTC-3430
Portable tool box
JTC-3460 ROLLER STITCHER
Wood handle for light and portable.
Bearing inside for easier use.
Spec: φ 38 x 5mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-3523 VALVE CORE TORQUE TOOL (25Ncm)
Prevents over or under torqueing.
Serves as both a core remover and installer.
Prevents premature tire failure due to
leaking valves.
Easy and simple to use.
Range of the torque: 25N.cm/2 lbf.in (+-6%)
Valve type: Rubber
Color: Red
JTC-3524 VALVE CORE TORQUE TOOL
Prevents over or under torqueing.
Serves as both a core remover and installer.
Prevents premature tire failure due to
leaking valves.
Easy and simple to use.
Range of the torque: 45N.cm/4 lbf.in (+-6%)
Valve type: Metal
Color: Black
JTC-3922 METAL T-HANDLE CLOSED EYE TOOL
Durable metal T-handle design.
Chrome -Molybdenum steel tip.
Tip length: 53mm
Changeable tip design
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-3923 METAL T-HANDLE RASP EYE TOOL
Durable metal T-handle design.
Chrome-Molybdenum steel tip.
Tip length: 72mm
Changeable tip design.
JTC-3926 NAP IN TIRE VALVE INSTALLER
Steel-constructed tool, deep threaded head
for positive sealing of all snap-in type
passenger car tire valve stems.
Rubber cover design to protect the rim.
3-position settled.
Patented.
JTC-3932 VALVE CORE REMOVER / INSTALLER TOOL
For installation and removal of
standard valve cores.
Has a screwdriver-style handle.
Tip diameter: 5.5mm
Tip length: 60mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4039 RATCHET EXHAUST PIPE CUTTER
This revolutionary tool works like a standard
ratcheting pipe cutter, but it can handle the
larger diameter of exhaust pipes.
Content:
o 1-1/8" ~ 2-1/2"
o 28 - 67mm
o Thickness ≦ 3mm
Suit for use on exhaust, tailpipes, thin-wall
copper and steel or stainless tubing.
JTC-4043 FLEXIBLE HOSE CLAMP FOR CLIP-R TYPE
For replacement of fuel, oil and water hose
with Clip-R hose clamp.
Hose clamp with flexible 630mm wire.
Convenient for working hidden areas and
long distance.
JTC-4055 WISHBONE EXTRACTION TOOL
Designed groove for adjust the position to
work easily.
To push down the wishbone and other
suspension parts, e.g. during the disassembly
of the drive shaft, during replacing the gaiter,
or exchange of the wheel bearing. After
loosening the ball joint the wishbone must, in
most cases, be pushed down against the
bush or stabilizer tension in order to pull the
joint from the support.
The work can comfortably and surely be
accomplished by one person.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4057 2-PC EXHAUST PIPE REMOVER
Designed especially for providing pull out
the exhaust pipe easily.
Special designed two-way for use with
17mm open wrench and 3/8" Dr. ratchet
wrench to adjust bolt to pull out the pipe.
JTC-4058 LIGHTWEIGHT 3-FUNCTION TIRE GAUGE- CLIP
TYPE
3-function (check, release, inflator) all
together on the press handle.
Large 80mm gauge with 360° swivel
function.
Tube length: 600mm
Lightweight design for easier
operation.
Weight: 0.63 kgs
Accuracy: under 110psi: ±2psi; above
110psi: ±4psi
Capacity: 170 psi / 12 bar (1200kpa)
JTC-4064 EXTRA LARGE C DISC OF JTC-1941
Extra-large disc 1pc for BMW E38,
Chrysler, and Renault etc.
Operation range:180 ~ 240mm
Only use with JTC-1941.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4065 EXTRA LARGE ROUND DISC OF JTC-1941
Special designed large round disc with
protective cover for BMW E39, E40
series.
Only use with JTC-1941
JTC-4069 LOCKING RING W/O EYELET PLIERS
Specially designed for removing and
installing wheel bearing locking rings without
eyelet.
Applicable: TOYOTA, LEXUS, CITROEN
JTC-4091 UNIVERSAL BUSH REMOVE AND INSTALL SLEEVE
SET
Universal application of step discs for
bearing bush, silent bearing, hydraulic
bearing, and rubber bearing on many
kinds of different vehicles.
20pcs sleeves: IDφ34 ~ φ72mm
(in 2mm increment)
2pcs step discs: use with sleeves
4pcs bolts: M10, M12, M14, M16;
Length: 450mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4098 EXTRA LARGE INNER TIE ROD TOOL
The master tie rod tools easily replaces inner
tie rod ends without removing the rack and
pinion.
Large size than JTC-1839.
Capacity: 40 ~ 47mm
JTC-4126 THIN TYPE LARGE BALL JOINT SEPARATOR
Special designed to remove the ball joint
in narrow space.
Mini operation space : 6 ~ 7mm
Jaws open: 28mm
Applicable: LUXGEN, etc.
JTC-4133 SUZUKI (JIMNY) FRONT WHEEL NUT SOCKET
(4-HOLES)
Special designed to remove the front
wheel nut with 4-holes.
Applicable: SUZUKI (JIMNY) 1.3
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4135 ANGLE LOCATOR
Special designed for wheel alignment with
adjustable locator.
Magnet diameter: 77mm
Size: 20(L) x 76(W) x 30(H) mm
JTC-4151 COIL SPRING COMPRESSOR
(WISHBONE SUSPENSION)
Suitable for lower wishbone diameter
size, which is smaller than 30mm.
Provided a 100Nm torque driver.
Available for using air impact.
Wide vehicle applications.
Patented on three-point lock key design.
JTC-4158 TOYOTA DRIVE AXLE NUT INSTALLER AND
REMOVER
Specially designed to make and remove
the fixing point on the nut of drive axle.
2-pcs in a set. One for making the fixing
point and the other for removing the
fixing point to remove the nut from drive
axle.
Length: 170mm
Applicable: TOYOTA, LEXUS
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4164 TOYOTA SUB-FRAME BUSH INSTALLER &
REMOVER
Removal and installation of rear rubber
mounts of axle suspension.
On car maintenance, does not need to
remove the sub-frame.
Applicable: TOYOTA
JTC-4190 BALL JOINT SEPARATOR (HIGH)
To remove the ball joint, which is longer
than normal vehicles.
Jaw open: 28mm
Jaw deep: 40mm
Inside height: 74mm
Applicable: BMW 7 series, BENZ S series,
LEXUS 460, etc.
JTC-4236 LIGHTWEIGHT 3-FUNCTION TIRE GAUGE
(ACCURATE TYPE)
All the function and weight are the same
as JTC-4058.
Accuracy: between 30~45 psi: ± 1psi, the
rest: ±2psi
Capacity:87 psi / 6 bar (600KPa)
Special designed for high accuracy requesting of tire pressure checking.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4252 10-L PNEUMATIC ATF & LIQUID DISPENSER
Use to extract, transfer, and dispense fluid quickly,
safety and cleanly.
Non-spark, one man operation.
10-L capacity reservoir with volume guide.
Screw valve to allow easy change extract or dispense.
Copper material, one touch coupler design for easy
operating.
Air inlet: 1/4"
Avg. Air Cons : 2 CFM
Temperature range: -20°C ~ 60°C
Provided with a safety valve, pre-setting 43 psi (3-
Bar), the exceed pressure will be relief automatically.
JTC-4306 FORD WHEEL HUB BEARING TOOL SET (78mm)
Special designed for installing and
removing the wheel hub bearing.
Operation on car.
External diameter of bearing fixing discs:
φ78mm
Applicable:
o FORD: Focus, CMAX
o MAZDA: M3
o VOLVO: C30, C70, S40, V50
JTC-4307 FORD WHEEL HUB BEARING TOOL SET (82mm)
Special designed for installing and
removing the wheel hub bearing.
Operation on car.
External diameter of bearing fixing discs:
φ82mm
Applicable: FORD, Focus, Mondeo
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4319 EXHAUST PIPE EXPANDER
Application range: 40~64mm.
Special designed to expend one of the pipe first, while contracting with exhaust pipe.
Applicable: Stainless steel
JTC-4323 BRAKE DISC & TYRE DEPTH GAUGE
Special device that allows the
measurement to be fixed while
measuring the disc thickness in different
locations.
Brake disc measure range: 0 ~ 60mm
Measure tyre depth.
Made of aluminum.
JTC-4328 PLASTIC HAND OPERATED OIL PUMP
Tank material: PE
Lid material: PP
Deliver rate: 75cc / cycle
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4454 10 – PCS TIRE PRESSURE SENSOR REMOVER /
INSTALLER SET
Specially designed to remove and install the TPMS in correct
torque.
Content:
o Fixed Torque 0.45 Nm Tire valve core installer
o Adjustable Torque 1.4, 3.3, and 4 Nm for
assembling TPMS
o TX – bits T10, T15, T20, and 1/4" bit adapter
o Holder thorn 2mm, and hex wrench
o 1/4" deep socket 11, and 12mm
Applicable: Most brand of TPMS.
JTC-4459 EUROPEAN CAR BALL JOINT REMOVER
(4 SIZES)
Specially designed for quick and easy removing the ball
joint connections.
Applicable:
o BMW E38, E39, E52, E53, E60, E61, E70, E83,
E90, E91, E92, R50, R52, R53, RR1, RR2, X5
o Mercedes W211, W219, W220 and W230
o PORSCHE 996 Carrera
o AUDI A4、AUDI A6 lower suspension ball
joint
Size: 24mm, 27mm, 31mm, and 36mm
JTC-4465 6 – BOLT HUB SEPARATOR
Use for removing the 6 holes HUB rear
axle.
JTC – 4817 is optional for using an axle
slide hammer.
Applicable:
o TOYOTA HIACE 100 series, 200
series
o NISSAN CARAVAN E25 series, E26 series
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4466 FRONT AXLE REMOVAL TOOL SET
This tool set is required when replacing the front HUB upper screw, brake disc, and bearing, etc.
Specially designed for removing each parts on the front HUB.
Applicable: o TOYOTA HIACE 200 series: 2WD, 4WD o NISSAN CARAVAN E25, E26 series: 2WD, 4WD
JTC-4468 BRAKE DISC RUN – OUT KIT
Quickly and easily to check the ball joint
abrasion and brake disc run – out.
The pliers can enable the dial gauge to
use in various angles against the brake
disc.
This kit includes a Metric calibrated dial
gauge.
JTC-4479 JAGUAR AXLE BEARING NUT SOCKET
Special tool removing and installing the
axle chamber bearing nut which with ABS
rotor on it.
Size: 3/4" Dr. x 12PT
Applicable: JAGUAR XJ8, XK8, etc.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4482 CITROEN & PEUGEOT BALL JOINT SOCKET
User for removing and installing the screw nut of the ball joint.
Use with 35mm / 6PT wrench.
Size: Ø 51mm / 4PT
Applicable: Peugeot 405 / Citroen
JTC-4487 TOYOTA REAR HANDBRAKE SPRING DRIVER
Specially designed tool that can reach
deeper to hold down the spring cup on
TOYOTA cars.
Applicable: TOYOTA Camry, Tacoma,
Tundra, FJ Cruiser, 4Runner, and Land
Cruiser since 2000.
JTC-4514 BOIL TEST BRAKE FLUID ANALYZER
True boiling testing base on SAE J1730.
Straight – stand design, for both nimble
and stable.
Less fluid wastage via the content cup.
User friendly, one button to complete the
test.
Durable ceramic core, available for racing fluid.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4528 REAR TRAILING ARM BUSH INSTALLER/REMOVER
(FORD, MAZDA, VOLVO)
Specially designed for easy removal and installation of the rear arm bush.
By using this tool can insert the bush to the correct depth.
Applicable: o MAZDA 3 BK 03 ~ 08, BL 09 ~
PREMACY 05 ~ 10 AXELA 03 ~ 09 5 CR 05 ~ 10
o FORD C - Max 03 – 07 FOCUS I CAK 98-05, CB4 08-11 , II 04
- 08 Kuga CBV 08 ~
o VOLVO S40 II 04 ~, V50 04 ~
OEM bush number: 98AG 5K896 AB
JTC-4537 UNIVERSAL SEAL INSTALLER
The spider arm can be trimmed to fit the seal, and
keep the seal centered during installation.
By using the long handle can install the pinion
seals in a flexible way.
Applicable: 32mm-60mm
Contents:
o Hex cap screw x1
o Waster x1
o Handle x1
o Small spider x1
o Large spider x1
o Spider insert x1
o 63mm driver x1
o 76mm driver x1
JTC-4539 ATF DIFFERENTIAL PRESSURE REFUELING
MACHINE
Refill or reflux the oil by using the pressure difference between the two uneven oil tanks.
After refueling, lower the oil tank to withdraw the extra oil.
Capacity: 4L (Can be refilled during use.)
Attached with 8 pcs adapter set, same as JTC-4252#D.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4540 OPEN TYPE STEERING KNUCKLE SPREADER
TOOL (SINGLE)
Adjustable tool designed for spreading the steering fixed seat of shock absorbers without damaging the aluminum or cast iron knuckle.
Made of chrome – moly steel for more strength.
Applicable: VAG, BMW, Citroen, FORD, Renault, Seat, Peugeot and most Japanese vehicles.
JTC-4541 OPEN TYPE STEERING KNUCKLE SPREADER TOOL
(TWIN)
Adjustable tool designed for spreading the
steering fixed seat of shock absorbers
without damaging the aluminum or cast
iron knuckle.
Applicable: Specially designed for twin ball
joints as fitted on VAG control arms.
Made of Chrome-moly steel for more
strength.
JTC-4548 HAND OPERATED GREASE PUMP
Capacity: 20L
Suitable for 00#~2# grease.
Deliver rate: 4cc / press
Hose length: 6 ft.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4564 BRAKE SHOE GAUGE
A time – saving tool for measuring the brake pad lining on the vehicle without removing the wheel.
Special slim design for measuring the distance between the lower side of the backing plate and brake disc.
Designed for both internal and external brake pads, features a 1.5mm and calibration check marking.
Capable for 6mm backing plate (class IV, V)
JTC-4640 CV JOINT BANDING TOOL (WITH CUTTER)
Operated by hand or 1/2" wrench.
This tool is easily removed by sliding
sideways after winding has been
completed.
JTC-4641 BEARING PACKER
To pack grease into bearing by easily compressing.
To add grease from the grease fitting in the top or removing the body.
Applicable: bearing max. I.D.??16mm and max O.D.??95mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4642 BALL JOINT SEPARATOR (17mm)
For splitting track-rod ends, anti-roll bar
mountings, ball joints, etc.
A: 17mm
MAX. B: 58mm
JTC-4643 BALL JOINT SEPARATOR (32mm)
For splitting track-rod ends, anti-roll bar
mountings, ball joints, etc.
A: 32mm
MAX. B: 80mm
JTC-4644 BALL JOINT SEPARATOR (45mm)
For splitting track-rod ends, anti-roll bar
mountings, ball joints, etc.
A: 45mm
MAX. B: 90mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4660 2–PCS RUBBER RING HOOK TOOL SET
Specially designed to pull the rubber ring
which connected with exhaust tube.
2 special angle hook attached.
JTC-4661 BALL JOINT SEPARATOR (HIGH)
Adjustable size for your convenient to fit
different vehicle.
Jaw opening: 20mm
Applicable height: 27 ~ 55mm
JTC-4663 EXHAUST SPRING CLAMP REMOVER / INSTALLER
Special design to hold opening the spring
clamp and replace the exhaust.
Total length: 300mm
Max. jaws opening: 60mm
Applicable: Paugeot, Renault, Citroen,
etc.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4672 INTERNAL BEARING REMOVER SET
Two function bearing remover for puller and
slide hammer.
Contents:
o 1 pc Tailpipe expanders (62mm)
o 1 pc Slide hammer
o 5 pcs Puller: 8~11mm, 12~17mm,
18~23mm, 24~29mm, 30~34mm
o 3 pcs Extension threads
Applicable: bearing I.D.: 8 ~ 34mm
JTC-4713 SHOCK ABSORBER RAM DISMANTLE SOCKET
To insert this tool in and twist 90° to pull
open the sleeve, and remove the ram.
Applicable: VW, AUDI, SKODA, SEAT,
FORD, BMW, CITROEN, RENAULT, &
PEUGEOT
JTC-4725 SLOTTED SOCKET 24mm
Special design for removing / installing
the steeling fixing nut on the truck.
Size: 1/2" Dr.4.0 x 24 mm
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4731 10–POINT IMPACT SOCKET (20mm)
Special designed for the fixing screw on the
rear torque frame of HONDA CR-V.
Size: 1/2"Dr. x 20 mm 10 points
JTC-4817 HUB SLIDE HAMMER PULLER (OUTSIZE HAMMER)
Extra-large internal hole for European car.
Coverage with five oval-shaped holes to meet different size of hubs.
Increasing the power of pulling with both hands held outsize slide hammer.
Hammer weights: 6.3 kgs
JTC-4829 SINGLE-WAY BRAKE BLEEDER TUBE
Simple way to release the remained
brake oil.
Adjustable black rubber adapter for
different size nozzle.
With simple screen to show the clear oil
and finish the work.
Capacity: 1000 c.c.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4855 EXTRA LARGE CUSTOM BUILT BUSH / BEARING /
SEAL DRIVER SET
This extra-large driver set allows you to build your own custom bushing driver. Select the required sizes and assemble your driver tool.
Discs are connected with a shaft and screw
which connects to the driver handle.
Build to suit the required seal bush or
bearing job.
Disc size: 70mm through to 150mm in 5mm
increments
JTC-4856 CUSTOM BUILT BUSH / BEARING / SEAL DRIVER
SET
This master set allows you to build your
own custom bushing driver. Select the
required sizes and assemble your driver
tool.
Build to suit the required seal, bush or
bearing job.
Disc size: G18mm through to 65mm in
1mm increments and 74mm
JTC-4868 EXHAUST PIPE HANGER STRETCHER
The stretcher removes exhaust rubber-
style hangers easily.
The slip-resistant handles and self-locking
force pin allow for quick removal of
rubber exhaust hangers.
A slim profile and 25° offset allow for
easy access to confined areas.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4873 HUB PULLER & SEPARATOR
Fix the plate on the tire screw thread, screw
the bolt to separate the wheel drive shaft
and hub by pushing.
Pick the fit output shaft adapter to meet
central screw, then lock in the transmission
shaft, put the frame on, lock the nut and fix
the screw to pull the wheel shell close to the
drive shaft.
Output shaft adaptor: M22 x 1.5, M24 x 1.5,
M27 x 1.5, M30 x 1.5
JTC-5341 3-JAW INTERNAL BEARING REMOVER SET
Use for removing the internal bearing, sleeve, and disc.
Range: 13 – 38mm
JTC-1001A 25-PCS FWD FRONT WHEEL BEARING TOOL
(WITH BEARING)
Great tool used to replace front wheel bearing without removing the steering knuckle & strut assembly.
As the spindle assembler isn’t removed, there is no need to align front end after the job is done.
Fits on most cars.
Applicable with hydraulic press.
Total 25 pcs brand new combination.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1023A PNEUMATIC FLUID EXTRACTOR
Capacity: 8.5 liters
Work pressure: 90 psi
Simple and easy to operate suitable for engine oil,
gear oil, transmission and brake fluid water.
Extract with 3 min for 5 liter engine oil.
Non-spark power oil extractor
Only operate by one man, clear operation. Save
manpower.
Quick and safety.
Heat – resistance Temperature: 60℃
4 sets / 9 kgs / 10 kgs / 3.8'
JTC-1142A BEARING SEPARATOR KIT
Bearing separator 9015 included.
Pullout the bearing with the H – type
beam and bolts.
JTC-1404A SPRING COMPRESSOR STAND
Rotate the steering disc to make it move up-down for quick
operation and labor-saving. Won’t leak oil like hydraulic type.
Special designed upper jaw to adjust up-down and front-back
direction for fixing the spring tightly, safely, and stabilized.
The compressor fixed base could hold the cylinder center very
easily and it's very convenient to dismantle.
The lower supporting stand could prevent the shock absorber
from moving downside to make the cylinder to be deformed.
Specially designed for dismantling shock absorber, applicable
for most cars.
Patented. 1. Rotate the gear wheel of the steering disc to drive the
upper jaws in up-down direction.
2. The fixing hook was installed inside carrier shim and the
jaw could be adjusted in up-down and front-back to the
appropriate position for pressing the spring safely.
3. Fix the cylinder in center position, no need to hold it
tightly as the lower will prevent it from being deformed. 4. Adjust up-down direction to support the shock absorber
for easier operation.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1452A POSITIVE & NEGATIVE CALIPER WIND BACK KIT
More adapters than 1613A for using on more
new model vehicles.
Two bodies with positive thread and
negative thread for different models.
Total: 21 pcs
JTC-1532A CV BOOT CLAMP PLIERS (HEAVY DUTY)
For assembly of new stainless steel clamp
– bands on drive – shafts where a torque
setting is required.
The 3/8" torque wrench is ideal to
provide the drive.
Made from CR-MO material, which is
rigid and durable.
JTC-1538A POCKET BRAKE FLUID TESTER
The tester can be a digital brake fluid tester
suitable for determining brake fluid quality.
Quality is tested and indicated on five LEDs in
terms of “per cent of water in the brake
fluid”.
LED display:
o Green: no water – OK
o Yellow: less than 1% of water – Warming
o Yellow/yellow: approx. 2% of water –
Warming
o Yellow/yellow/red: approx. 3% of water
– The oil should be changed
o Yellow/yellow/red/red: At least 4% of water – Change the oil quickly.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-1610A FWD FRONT WHEEL BEARING TOOL
Great tool used to replace front wheel
bearing without removing the steering
knuckle & strut assembly.
As the spindle assemble isn’t removed, there
is no need to align the front end after the job
is done.
JTC-1613A 15–PCS CALIPER WIND BACK KIT
Winds back brake piston for replacing
brake pads.
Fits on most cars.
JTC-1943A STEERING WHEEL REMOVER / LOCK PLATE
COMPRESSOR SET
Removing steering wheels of most
vehicles with or without telescoping tilt
steering columns is easy with this set.
The steering wheel lock plate compressor
is also included to compress the steering
wheel lock plate to remove or install the
snap ring.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-3922L METAL T – HANDLE CLOSED
EYE TOOL
Durable metal T – handle
design.
Chrome – Molybdenum steel
tip.
Tip length: 73mm
Changeable tip design
JTC-4144A HAND OPERATED ATF FLUID DISPENSER
Tank capacity: 9.5 liters
Flow capacity: 75 cc /cycle
Hose size: 3/8" x 1500mm
Size: 330 x 260 x 650mm
Special designed for filling ATF oil.
Replaceable fittings for different vehicles.
With hand pump for vacuum to prevent oil deterioration.
Weight: 3.5 kg
Contains 8 fittings.
JTC-4219 WHEEL STUD ALIGNMENT GUIDE
TOOL
Assists when mounting
wheels, especially late
models with long lug bolts.
Applicable: All Mercedes
models with lug bolts.
Size: 2-M12 x 1.25, 2-M12 x 1.5, 2-M14 x 1.25, 2-M14 x 1.5
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4144A OPTIONAL FITTINGS:
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-4920S HUB SLIDE HAMMER SET
With 4 – holes and 5 – holes for all the
vehicles.
Increasing the power of pulling with both
hands held outside of slide hammer.
Hammer weight: 6.3 kgs.
JTC-F0412 BALL JOINT SEPARATOR (24mm)
Tempered drop forged steel one piece
construction for long & rough usage.
15/16" (24mm) Fork, 11-7/8" (300mm)
length replace worn out ball joint easily
with a hammer strike.
Can remove CV drive shafts on FWD vehicles.
JTC-F0416 BALL JOINT SEPARATOR (18mm)
Tempered drop forged steel one piece
construction for long & rough usage.
21/32" (18mm) Fork, 16" (410mm) length
replace worn out tie rods easily with a
hammer strike.
Can separate shock absorber links.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-F1954 BALL JOINT SEPARATOR
Heat treated drop forged steel body & bolt
for long rough usage.
Spread ball joints easily where space
prevents use of direct method.
Jaw open: 19mm
JTC-F270 DROP FORGED COIL SPRING COMPRESSOR
Drop forged CR-V steel jaws & leaded
screws (270mm) both heat treated
ensure you obtain professional job
performance.
The tool is designed for use in limited
space under wheel arch.
Jaw design is fitting to warp coil claws for
safely.
Maximum jaw opening is
270mm.
JTC-F370 DROP FORGED COIL SPRING COMPRESSOR
Heat treated drop forged CR-V steel jaws
& leaded screws (270mm).
The tool is designed for use in limited
space under wheel arch.
Special design claws to warp on coil
spring safely.
Maximum jaw opening is 270mm.
UNDERCAR SERIES
JTC AUTO TOOLS
2600 Northlake Dr. Suite F,
Suwannee, GA, 30024
JTC-J01 DISC BRAKE PISTON SEPARATOR
Fits in brake caliper to push back pistons for
new brake pads installation.
Patented.