Unboxing Manual Felix 1 5b Assembled v1
Transcript of Unboxing Manual Felix 1 5b Assembled v1
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
1/12
[email protected] www.felixprinters.com Page 1 of12
UNBOXING MANUAL OF FELIX 1.5 REVB
IMORTANT WARNING:
Follow this manual carefully before unboxing further.
Not reading this will potentially increase damaging of your newlypurchased Felix 1.5 3d printer!!!
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
2/12
[email protected] www.felixprinters.com Page 2 of12
1 INTRODUCTIONFirst of all thank you for your purchase of the Felix 1.5 3d printer. Please follow this manual carefully in order to
properly prepare your printer for printing.
2 REQUIRED TOOLS TO FINALIZE THE ASSEMBLYTo finalize the assembly e the following tools are required
Allen key size:
2.5mm 3mm 5mm
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
3/12
[email protected] www.felixprinters.com Page 3 of12
3 OPENING THE BOX
WARNING:
DO NOT MOVE ANY of the axis at a high speed by hand. The motors can generate power that way and
potentially burn out the electronics.
Open the box from the topside. Thats where the shipping labels are positioned.
Start removing the chips, untill the table and frame are exposed
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
4/12
[email protected] www.felixprinters.com Page 4 of12
Lift out the frame including table. WATCH OUT: The table is attached with wires to the frame of the printer!!
Put the printer on the wide beam like indicated below. Remove the bubble wrap paper from the table.
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
5/12
[email protected] www.felixprinters.com Page 5 of12
Place the table assembly on the z-axis fork according to the picture. Be careful with the table that you dont exert
too much force on the plate. Mount the table with the 4 supplied m3x16 bolts.
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
6/12
[email protected] www.felixprinters.com Page 6 of12
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
7/12
[email protected] www.felixprinters.com Page 7 of12
4 PLACE THE LOOSE BEAM ONTO THE REST OF THE FRAME
Look at orientation
of two holes
Also look at thedampening feet
Look at orientation of
small hole
2 holes are located here
Slide beam on
frame on the
frame bolts
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
8/12
[email protected] www.felixprinters.com Page 8 of12
Put the beam in position. So that the holes are aligned in a way you can tighten the frame bolts. See pictures
below.
When tightening make sure the beams in question are aligned properly. See picture below.
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
9/12
[email protected] www.felixprinters.com Page 9 of12
Topview of frame
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
10/12
[email protected] www.felixprinters.com Page 10 of12
5 PLACE BELT ON Y-AXIS.Guide the belt as indicated in the picture below.
On the side with the opto-sensor switching vane. Put some tension on the belt by hand and push it in place in
place.
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
11/12
[email protected] www.felixprinters.com Page 11 of12
With an allen key put some tension on the belt, by turning the belt clockwise.
It should feel firmly.
-
7/30/2019 Unboxing Manual Felix 1 5b Assembled v1
12/12
[email protected] www.felixprinters.com Page 12 of12
6 FINISHING TOUCH.Get the end-cap and put it in place.
Your printer is physically prepared for printing. Please continue reading our user manual which can be downloaded
at.www.felixprinters.com/downloadsand start reading at chapter 14. Making printer ready for operation.
http://www.felixprinters.com/downloadshttp://www.felixprinters.com/downloadshttp://www.felixprinters.com/downloadshttp://www.felixprinters.com/downloads