1ULTIMATE QUICKSTART

For Electronic Frequency Therapy Machines

English

2011- 2013

2Technical Description

Frequency range0:01 kHz - 999.99 kHz (1 MHz)

Frequency waveform24 MHz Microprocessor Audio Frequency with square waveform; lab tested pure squarewave form on all Rife frequencies.

Harmonic frequencyLaboratory tested harmonic waveform periodic on 100% frequencies

Voltage input12 V-16 DC (110 V / 250 V SMPS) All world voltages accepted, external DC switching-mode power supply adapter.

Voltage output (Multimeter)6V-7.5v DC with 100% positive offset

Voltage output (Oscilloscope)11V-14v DC with 100% positive offset

Operating input current4500 mA

CPU Operating Temperature (Safe) *34 - 43 Celcius93 - 109 Fahreneit (Normal Operating Temperature)

RCA Output socket1 RCA Socket with adapter for 4 straps

- 1 Set of hand straps- 1 Set of foot straps

1 RCA Splitter

* Frequency Generators operate at higher temperatures, This is normal and safe for yournew generation frequency device.

3QUICK START

(1) Plug in Power plug(2) Plug in Wrist-strap/Foot-strap plug(3) Press Power Button on top right

(4) MACHINE STARTS IN IDLE MODE

4I = IDLE MODE

You can press arrows in the navigation console (seeabove) to view all pre-programmed frequencies.

Frequency presets are: 100.00 to 999.99

Press to view all 10 presets. Number on the right of i isthe frequency position number

i = IDLE Mode: This is a viewing mode only. There is nooutput under Idle mode, and the Frequency Output light remainsoff. Only thekeys function in the navigation control

5R = RUN MODE

(1) In i (idle mode) Use to select the menu position youwish to RUN(2) Press RUN. Green Output light is now on(3) Put Foot-straps on your feet(4) Frequency Generated is 200Khz (example)(5) Menu Position number is r1 (example)(6) Green Frequency light remains on until you press RUN keyagain, or you turn the unit off.(7) There is no timing function under RUN so the FrequencyGenerator will run indefinitely(8) [] Press RUN key again to PAUSE session(9) [] Press RUN key again to Continue session from whereyou left off.

6S = SWEEP MODE (Default Frequencies)

(1) Press SWEEP key(2) Green Frequency Output light turns on(3) Put Foot-straps on your feet to begin session(5) Sweep starts at first menu position Zero (s)(6) Sweep moves from first preset to last preset for intervals of 10minutes per frequency(7) Defaults: -9, which are 100 999.99 Khz(8) Sweep remains on until you press SWEEP key again, oryou turn the unit off.(9) Sweep runs on a continuous LOOP cycle.(10) Indication of menu position is displayed to the right of s (-9)

7P = PROGRAM MODE

(1) In i (idle mode) Use to select the menu position you wish to edit( 9)(2) Press P (Program) Key to EDIT(3) Blinking Cursor shows cursor position(4)Key moves Cursor Right(5)Key moves Cursor Left(6)Key Selects numbers - 9(7)Key Selects numbers 9 - (8) Press P (Program) Key to RECORD(9) Screen Displays Wait.(10) Frequency is recorded into memory(11) Programs cannot be erased with Power Off

8P = PROGRAM MODE (Example 2.78Khz)

(1) Look up a Disease / Illness in the ETDFL book(2) Select first frequency, in this example: 2.78(3) Press P (Program) Key to EDIT position (4) PressKeys to program in 1st Freq.(5) Press P (Program) Key to RECORD Freq.(6) Screen Displays Wait.(7) Frequency is recorded into memory(8) Do this P (Program) for all 10 Frequencies next to the disease condition(P: 0-9)(9) In i (Idle mode) usekeys to preview the frequencies entered.

If you find an error in your programming, press P to quickly edit the currentnumber. Turning the machine OFF while you are in P mode will cancel thetransaction.

9S = SWEEP MODE (Your Recorded Programs)

(1) All 10 Frequencies are now recorded.(2) Put Foot-straps on the soles of your feet, with the Silver buttonin contact with the soles.(3) Press SWEEP key to begin treatment(4) Green Frequency Output light turns on.(5) First Frequency (e.g. 2.78Khz) commences.(6) The 10 Frequency Presets in positions -9 will be run for 10minutes each.(7) Cycle is LOOP: continuously.(8) [] Press SWEEP key to PAUSE session(9) [] Press SWEEP key again to Continue session fromwhere you left off.

10

MASTER RESET

MASTER RESET BACK TO DEFAULT:

- Default settings are: (KHZ)100,200,300,400,500,600,700,800,900,999.99(999.99 is considered the 1 million Hz setting)-Frequency settings in menu positions -9 will be erased andreplaced with the above defaults.

(1) Turn off machine(2) Power light is on, and display is blank(3) Hold Down 1- P and at the same time press 2- On button(4) Machine has RESET back to factory default

11

WARNING: When using the Ultimate Frequency Generator you may experience a tinglingsensation on your skin. This is unlikely to happen in the palms of your hand; however onsensitive places, like your stomach, wrists or softer skin areas, this tingling may occur.

Leaving the wrist-strap terminal on your sensitive skin (like the wrists) will result in a rash, so donot leave on softer skin if you feel this tingling sensation. One of the best places to conducttreatment sessions for longer periods (hours) is to place the Straps over your foot, so that themetal button touches the under sole of your left and right feet. The under soles of your feethave tougher skin and will be able to bear the extended periods of electro-therapy.

We suggest connecting the Straps only to the soles of the feet with the Blue/Green Conductivestrap facing the underside of the foot, and the Stainless Steel button making contact with thesoles.

Use Straps only inthe PALMS OFHANDSOr on theSOLES OF YOURFEETAs Pictured Here

CautionUsing Straps on the

Wrists may cause skinirritation

12

FREQUENTLY ASKED QUESTIONS:

Q. How do I Run a program longer than 10 minutes?A. Program the same frequency in twice to run that frequency for 20 minutes.(Use SWEEP command)

Q. How do I Run a program for less than 10 minutes?A. 10 minutes is a minimum recommended time for frequency exposure andpositive healing results.

Q. How long should I use the machine?A. See the main Instruction manual under chapter 6.1. Generalrecommendations:

Q. I cant find my frequency in the book?A. Please email us. Medical definitions can change over time, or you looked inthe wrong section of the book

Q. I want a timed On / Off frequency; how can I do it?A. How to set a Program of 10 minutes on and 20 minutes off:Example Program menu :30.00, 1:0.00, 2:0.00, 3:30.00, 4:0.00, 5:0.00,6:30.00, 7:0.00, 8:0.00, 9:00.00. Add Zeros (null menu) for 10 minutes OFF,and add an actual frequency for ON. Adjust timer On or Off, according to yourown requirements.

Q. Does my model use a 12v or 16v DC adapter?A. 2011 models were released with 12v DC. This was upgraded to 16v in the2013 models. A multi-meter will show output to be 6v for 2011, and 7.5v for 2013model.

Q. I plug in the power, but no lights come on??A. Check that your power is turned on at the wall socket. Check that the Countryadapter is seated correctly in the device. The problem is usually always with thepower adapter. Try using a different 12-16VDC power adapter.

Q. On frequency 0.01 0.03 the green light flashes??A. This is okay, and is only a technical indicator showing Ultra Low Frequencies.

Q. I cant feel the pulse/frequency on the soles of my feet.A. The Machine is tuned to the highest voltage / frequency output withoutcausing skin rash/burn (so it is pre-set to the highest value). Some people feelthe subtle pulse, some people cannot. It makes no difference to the effectiveness

13

of the treatment whether you feel it or not.

Q. I want to run this machine on battery or in my car.A. You can run this device on a car cigarette lighter (12-14v DC). An external12v DC rechargeable battery can be used at home, but must be rated at about1000+ milliamp. (Plug specs: Power Jack Plug 2.5mm) (+) -

Q. How do I hook this machine up to my dog / cat?A. For Dogs and Cats: Wrap the 2 straps around a pillow with the silver buttonfacing up, and let the pet lie down on the new pillow, with the 2 buttons facing theunderside of their stomach. Use for 1-2 sessions per day.

FOR ALL DOMESTIC AND INTERNATIONAL SALES AND INQUIRIES

Email:

rifedigitalmachines@gmail.com

Website:

www.rifedigitalmachines.com