ADJUSTING RIDE HEIGHT.

NOTE: Extending shock assembly lowers

frame/fender height. Shortening shock

assembly will raise frame/fender height.

NOTE: Always check clearances during & after

adjusting ride height.

Step 1: Loosen ride height adjusting locknut.

(see fig. 3)

Step 2: Rotate end to desired height. Always

leave at least 1 inch of threads engaged

in the female threaded shaft. (see fig. 4)

Step 3: Lock down ride height adjusting locknut

using blue (med strength) threadlocker.

(see fig. 5)

Step 4: After adjusting ride height on both

shocks, verify that they are the same

length by measuring from their mounting

points. (see fig. 6)

ULTIMA SOFTAIL STYLE ADJUSTABLE SHOCKS

Always wear protective eyewear when adjusting shock ride height or spring preload.

NOTE: Adjusting spring preload will not only stiffen or loosen absorption properties but will also change handling

behavior of the motorcycle.

NOTE: Adjusting ride height will change handling behavior of motorcycle.

NOTE: After ride height & preload have been set verify shocks are the same length by measuring from center to center

of mounting points.

NOTE: The procedures outlined in these instructions can be done with shocks installed on or off the bike.

ADJUSTING SPRING

PRELOAD (STIFFNESS).

NOTE: Shocks typically come set at their loosest

(softest) setting.

Adjustment range is approximately 4 full

rotations.

Step 1: Loosen preload adjustment locknut.

(see fig. 1)

Step 2: Using supplied special tool with a 3/8

ratchet, turn adjusting plate clockwise to

stiffen preload & counter-clockwise to

loosen preload. (see fig. 2)

Step 3: Once preload has been set, lock down

preload adjusting nut using blue

(med strength) thread locker.

FIG. 1 FIG. 2

FIG. 3 FIG. 4

FIG. 5

FIG. 6

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice