UDC P RO - Tactical Electronics€¦ · One) Under Door Camera Pro (2-camera system) » Two...

TACTICALELECTRONICS.COM

PRODUCTS / EOD TRAINING / R & D / AVIATIONDESIGN / ENGINEERING / MANUFACTURING

HEMLOCK FACILITY

2200 NORTH HEMLOCK AVE / BROKEN ARROW, OK / 74012V: 866.541.7996 / V: 918.249.8326 / F: 918.249.8328

CRUSADER FACILITY

2844 CRUSADER CIRCLE / #100 / VIRGINIA BEACH, VA / 23453V: 757.689.0476 / F: 757.689.3769

UNDER DOOR 2-CAMERA SYSTEM

UDC PROTACTICAL ELECTRONICS

Products

OPERATION ANDSUPPORT PUBLICATION

PROPRIETARY

2

PROPRIETARY

UNDER DOOR 2-CAMERA SYSTEMUDC PRO

3

Manual Contents

Kit Identification

Power-up

Operation

Monitoring Options

Specifications

3

4

5

6-9

10-15

16

One) Under Door Camera Pro (2-camera system) » Two cameras: forward and upward facing cameras » Internal mini DVR with SD card recording capabilities » 16GB SD card » Two 0.005 lux black & white CCD chip at the distal end of insertion panel » Insertion Panel only 0.262” thick » IR LED illuminator (1) for flood illumination » IR LEDs (4) for forward illumination » >100mW @ 2400 mHz transmitter onboard

One) Telescoping deployment pole

One) Hard-wire cable (with inclusion of Handheld Monitor Pro) » Used for hard-wire operation with Handheld Monitor Pro

One) Monitoring option of your choice (Wrist Monitor Pro or Handheld Monitor Pro) » Handheld Monitor Pro has a 5.0” screen » Wrist Mounted Monitor Pro gives the operator a 3.5” screen on the arm

One) Storm Case® w/ precision cut foam for stable storage environment » Unbreakable » Watertight » Airtight » Corrosion Proof

OPERATION AND SUPPORT PUBLICATIONUDC PRO KIT IDENTIFICATION 4

Tactical Electronics & Military Supply

* Always remove batteries when not in use

• The UDC Pro Under Door Camera is powered by four 3Volt Photo Lithium batteries. Most manufacturers of these cells designate them as size 123 or CR123A. Tactical Electronics systems draw high current; use only GE SANYO, ENERGIZER, or DURACELL batteries. Testing has proven those batteries to provide the longest run time in our products.

• Run times will vary, components in this system are designed to optimize power management and power sharing when hard-wired together. Usage of IR LEDs will also contribute to varied run times.

• The diagrams below demonstrate proper battery installation and power-up for the UDC Pro Under Door Camera.

» Battery Life Indicator:

The LED power indicator will flash red and green to indicate low battery power.

As battery life continues to diminish the LED indicator will illuminate solid red. After the LED illuminates solid red the unit will shut down within 10 minutes.

When battery life is critical the LED indicator will illuminate solid blue. Once this occurs the UDC Pro will only remain ON for 10-15 seconds while the system shuts down to protect recorded video on the SD card.

» Battery Compartment & Power-Up Procedure:

The UDC Pro (left) requires four 3V Lithium batteries for operation. Use the battery orientation diagram adhered to the UDC Pro for reference.

NOTE: For SD card recording, ensure the SD card is inserted before powering ON the UDC Pro.

The power switch for the UDC Pro is a push button located on the side of the unit. The picture (left) identifies the UDC Pro power button. Fully depress the power button to power ON and OFF the UDC Pro.

Immediately after the UDC Pro is powered ON the LED indicator will illuminate a solid blue for approximately 8-10 seconds while the system initializes. Once the power-up phase is complete the LED indicator will illuminate a solid green indicating full operational use (If no SD card is inserted, the LED indicator will flash red).

NOTE: When the UDC Pro is powered ON all IR LEDS are powered OFF by default.

To power OFF the UDC Pro, hold down the power button for 3 seconds to begin power down cycle - when the LED illuminates blue release the power button and the unit will power OFF within 5 seconds.

NOTE: DO NOT open the battery door before powering OFF the UDC Pro. Failure to properly power OFF the unit will result in loss of recorded files.

OPERATION AND SUPPORT PUBLICATIONUDC PRO POWER UP 5


LED indicators

» Operation:

The UDC Pro Under Door Camera is shown (left) in proper operating position on a flat surface as if it were being slid under a door.

» Insertion Panel:

The distal tip of the UDC Pro houses both the forward and upward camera lenses, the IR flood illuminator, the microphone, and four (4) directional IR LEDs. The 0.005 lux camera chip is located in the tip of the insertion panel and slides into the room when the panel is placed underneath a door.

The unit's IR LEDs are mounted on each side of the camera lens for enhanced viewing in low-light situations.

OPERATION AND SUPPORT PUBLICATIONUDC PRO OPERATION 6


» IR LED Modes:

The UDC Pro provides four stages of IR illumination. By default all IR LEDs are powered OFF upon every power up of the UDC Pro.

To cycle through the IR LED modes depress the IR LED button (shown left). The current state of the IR LEDs will be displayed on the monitor screen.

Remote toggle of IR illumination: Depress the "IR" button on the Wrist Mounted Monitor Pro or the Handheld Monitor Pro to remotely cycle through the IR LED illumination modes. The IR LED modes cycle through the following order: NO IR - Forward IR - Flood IR - Both IR

NOTE: Use of the IR LEDs directly affects the battery life of the unit.

NOTE: The UDC Pro body will become quite warm during use, especially while using the IR LEDs. This is normal.

Outgoing channel selector

0.25in jack

» Hard-Wire Transmission:

The 0.25 inch jack (shown left) is used for hard-wire operation between the UDC Pro and the Handheld Monitor. Simply power ON both the UDC Pro and Handheld Monitor, then insert the male/male cable into the 0.25in jacks on each unit. Hard-wire operation disables the wireless signal.

» Wireless Transmission:

Wireless operation of the UDC Pro is very simple. Follow proper UDC Pro power-up procedure and the unit will automatically transmit wireless video signals.

Once the UDC Pro is powered ON, the unit immediately begins transmission of an RF video signal. When a monitor is powered ON the monitor begins receiving the video signal from the UDC Pro. Cycle through the channels on the monitor until a picture is displayed.

» Channel Selector:

To determine which channel the UDC Pro is transmitting, simply power ON both the UDC Pro and monitor. Use the channel selector button(s) on the monitor to cycle through each channel until a picture is displayed on screen.

• Shown left is the UDC Pro Outgoing Channel selector.

The UDC Pro will only transmit on channels 1-4. If a channel outside this range is selected the UDC Pro will not transmit. Hard-wire, recording, and IR LED functionality will remain operational.



Wrist Mounted Monitor Pro

Push Pole attachment

» Telescoping Push Pole Attachment:

The UDC Pro supports a Telescoping Push Pole. The Push Pole is designed with a magnetic ball attachment, located at the end of the pole.

To attach the Push Pole to the UDC Pro simply place the magnetic ball onto the mount located on top of the UDC Pro. Once the Push Pole is attached the user is capable of placing the UDC Pro on target and maneuver via the Push Pole.

To detach the Push Pole from the UDC Pro, rotate the pole until the steal pin at the end of the pole pushes away from the unit and releases from the magnetic mount.

» Dual View Camera Selection:

The UDC Pro 2-Camera System contains two light sensitive B/W cameras that provide forward and upward camera views. The forward camera angle provides a view of a room's interior while the upward camera angle provides view of the interior side of a door. Both cameras are housed within the unit's insertion panel.

Manual toggle camera views: Depress the "Camera" button (located on the side of the UDC Pro) to manually toggle between the forward and upward camera views.

Remote toggle camera views: Depress the "Camera" button on the Wrist Mounted Monitor Pro or the Handheld Monitor Pro to remotely toggle between the forward and upward camera views.

Remote toggle of IR illumination: Depress the "IR" button on the Wrist Mounted Monitor Pro or the Handheld Monitor Pro to remotely cycle through the IR LED illumination modes.



Wrist Mounted Monitor Pro



» SD Card Recording:

Insert the SD card into the SD card slot with the UDC Pro powered OFF. DO NOT insert or eject the SD card with the UDC Pro powered ON; otherwise, recorded video files will not finalize and will become corrupted.

Immediately after the UDC Pro is powered ON, the LED indicator will illuminate a solid blue for approximately 2-5 seconds while the system initializes. Once the power-up phase is complete the LED indicator will illuminate a solid green indicating operational use and proper SD card recording.

If the UDC Pro system indicates a recording error, “REC ERROR” will display on the monitor(s) in use. If “REC ERROR” is displayed, power OFF the UDC Pro, reinsert the SD card, and power ON the unit.

The UDC Pro will transmit video without the use of SD card recording. If the unit is powered ON without an SD card inserted "REC ERROR" will be displayed on the monitor(s) in use. The LED indicator on the UDC Pro will also flash red to indicate no SD card present.

» SD Card Viewing:

To review recorded video files: Power OFF the UDC Pro, eject the SD card, and insert the SD card into an SD card reader on a computer.

All files will be under the folder DCIM\100Media on the SD card. Recorded files will be listed sequentially in numerical order. All recorded video files are AVI files, and are easily viewed in Windows Media Player or VideoLan's VLC Player. AVI files may also be viewed in QuickTime with the appropriate plug-in.

» Audio:

The UDC Pro houses an omnidirectional microphone and records audio and video directly to the SD card for post operational review.

* Push in SD Card to eject

microphone

• Tactical Electronics video systems are designed to operate interchangeably with each wireless monitor: Wrist Mounted Monitor (WMM), Handheld Monitor (HHM), Monocular Micro Viewer (MMV), Heads-Up Display (HUD), Wrist Mounted Monitor Pro (WMM Pro), or Handheld Monitor Pro (HHM Pro).

• Each monitor is programmed to receive a frequency transmitted directly from the purchased camera system. If multiple camera systems are in use, the monitors are equipped to receive separate channel frequencies in order to view and cycle between various Tactical Electronics camera systems.

» WMM Operation

The Wrist Mounted Monitor has a 3.5 inch LCD screen that displays B/W or color video transmitted from the camera source.

The monitor contains an internal receiver, and when powered “ON” automatically receives RF video signals from the chosen camera. The WMM is completely wireless and cannot be hard-wired.

» Wrist Mounted Monitor (WMM)

The Wrist Mounted Monitor is powered by two 3V Lithium batteries. The batteries are to be inserted positive (+) terminal first.

The power switch for the Wrist Mounted Monitor (left) is the top button near the battery cap. Press and hold the power button for approximately 3 seconds to power “ON” the WMM. The screen will display the current channel and battery power meter when the unit is “ON”.

Always remove batteries when not in use.

IMPORTANT: If lines begin to appear across the screen, the lines are most likely a sign of LOW BATTERIES.

» WMM Channel Selection

If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen.

To determine a camera’s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen.


OPERATION AND SUPPORT PUBLICATIONMONITOR OPTIONS 10

Power

Channel Selector

» HHM Operation

The Handheld Monitor has a 5.0" LCD screen that displays B/W or color video transmitted directly from the camera source.

It has a built-in receiver and when powered “ON” automatically receives an RF video signal until a hard-wire is plugged in or the HHM is powered “OFF”.

» Hard-wire Connection

The Handheld monitor provides a direct hard-wire connection to compatible camera systems.

NOTE: When working in extreme low light environments hard-wire the Handheld Monitor to the camera system (if hard-wire option is available with the camera system). A hard-wire connection provides a slightly brighter picture on the Handheld Monitor that will be beneficial for low light situations.

» Handheld Monitor (HHM)

The Handheld Monitor (HHM) is powered by four 3V Lithium batteries, AC, or vehicle power via cigarette lighter plug. The 3V Lithium batteries that are to be inserted negative ( - ) terminal first.

The power switch for the Handheld Monitor (left) is a rocker type. The green LED is illuminated when the unit is “ON”.

Always remove batteries when not in use.




» HHM Channel Selection



NOTE: Slight adjustments in your viewing angle can greatly affect the quality of the picture.

Power

Channel Selector

Hard wire jack

» Monocular Micro Viewer (MMV)

The MMV is powered by one 3V Lithium battery. Unscrew the battery cap [shown left] to insert the battery. The 3V Lithium battery is to be inserted according to the battery orientation diagram on the MMV. Always remove batteries when not in use.

The power button for the MMV (left) is a rubber push button on the side of the unit. The LED indicator will illuminate green and the video display will slightly illuminate when the unit is powered “ON”.

NOTE: The On Screen Display (OSD) will show a flashing battery icon when the battery is close to critically low levels.

» Wireless Video

The MMV has a built-in receiver, and when powered “ON” automatically receives RF video signals from the chosen camera. The MMV is completely wireless and cannot be hard-wired.

If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When toggling, the current channel will be displayed on screen. To determine a camera’s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen.

NOTE: Any time the channel is changed on the MMV the shutdown timer is reset. Since the initial press of the channel button resets the shutdown timer and displays the current channel, it is necessary to press the channel button more than once to change channels.

» Automatic Shutdown

To preserve battery life the MMV will automatically shut off if the unit is idle for approximately 90 seconds. When the unit is nearing automatic shutdown the OSD will show a series of disappearing dots as a countdown timer.

To prevent automatic shutoff: Press the channel button once to reset shutdown timer, allowing another 90 seconds of video display. A single press of the channel button will also display the current channel the MMV is receiving.

» LED Indicator

• The LED will momentarily light up blue when the unit is first powered on, then will illuminate solid green.

• The LED will illuminate blue whenever the channel button is pressed.

• The LED will momentarily illuminate red when the unit is powering down.

• The LED will illuminate solid red when the battery is low.



POWER

battery cap

channel selector



POWER

channel selector

» Heads-Up Display (HUD)

The Heads-Up Display is powered by two 3V Lithium batteries, The 3V Lithium batteries are to be inserted positive ( + ) terminal first. Always remove batteries when not in use.

The power switch for the Heads-Up Display (left) is a rubber push button on the front of the unit. The display slightly illuminates when the HUD is powered “ON”.

To power “OFF” the HUD press and hold the power button. A red LED in the left eyepiece will illuminate momentarily, indicating the unit is ready to power down. Release the power button.

NOTE: The On Screen Display (OSD) will show a flashing battery icon when the battery is close to critically low levels.

» HUD Channel Selection



Note: The first press of the channel selector button will display which channel the HUD is receiving as well as current battery power. To change the channel press the channel selector button again within three seconds.

» HUD Mounting

The HUD comes standard with the Wilcox 14001G01 Wilcox NVG Mounting Shoe. This mounting shoe is compatible with most Wilcox NVG Mounting Systems.

To mount the HUD to the Wilcox NVG Mount, slide the attached mounting shoe into the appropriate slot on the NVG Mount until the HUD system clicks solidly into place.

Detach the HUD from the NVG Mount using the release mechanism on the NVG Mount.

» HUD Operation

The Heads-Up Display gives the operator the appearance of a 35-inch screen at a 7 foot distance. The HUD displays B/W or color video transmitted directly from the camera source.

It has a built-in receiver, and when powered “ON” automatically receives RF video signals from the chosen camera. The HUD is completely wireless and cannot be hard-wired.

» Wrist Mounted Monitor Pro (WMM Pro)

The Wrist Mounted Monitor Pro is powered by two 3V Lithium batteries. The batteries are to be inserted positive (+) terminal first.

The power switch for the WMM Pro (left) is the top button near the battery cap. Press and hold the power button for approximately 3 seconds to power “ON” the monitor. The screen will display the current channel and battery power meter when the unit is “ON”. Always remove batteries when not in use.


» WMM Pro Operation

The WMM Pro has a 3.5 inch LCD screen that displays B/W or color video transmitted from the camera source.

The monitor contains an internal receiver, and when powered “ON” automatically receives RF video signals from the chosen camera. The WMM Pro is completely wireless and cannot be hard-wired.

» Remote Toggle

If the camera system in operation is capable of remote toggling follow the instructions below to toggle between camera views and/or IR LED illumination modes.

Remote toggle camera views: Depress the “Camera” button on the Wrist Mounted Monitor Pro to remotely toggle between separate camera views.

Remote toggle of IR illumination: Depress the “IR” button on the Wrist Mounted Monitor Pro to remotely toggle through IR LED illumination modes.

» WMM Pro Channel Selection

If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When cycling, the current channel will be displayed on screen.


NOTE: Slight adjustments in your viewing angle can greatly affect the quality of the picture.


OPERATION AND SUPPORT PUBLICATIONPRO MONITOR OPTIONS 14

Power

IR Toggle

Camera Toggle

Channel Selector

» Handheld Monitor Pro (HHM Pro)

The Handheld Monitor Pro (HHM Pro) is powered by four 3V Lithium batteries, AC, or vehicle power via cigarette lighter plug. The 3V Lithium batteries that are to be inserted negative ( - ) terminal first.

The power switch for the HHM Pro (left) is a rocker type. The green LED is illuminated when the monitor is “ON”. Always remove batteries when not in use.


The monitor contains an internal receiver and when powered “ON” automatically receives an RF video signal until a hard-wire is plugged in or the HHM Pro is powered “OFF”.

» Remote Toggle

If the camera system in operation is capable of remote toggling follow the instructions below to toggle between camera views and/or IR LED illumination modes.

Remote toggle camera views: Depress the “Camera” button on the Handheld Monitor Pro to remotely toggle between separate camera views.

Remote toggle of IR illumination: Depress the “IR” button on the Handheld Monitor Pro to remotely toggle through IR LED illumination modes.

» HHM Channel Selection

If multiple camera systems are in use, all monitors are equipped to receive four separate channel frequencies. Use the channel selector button in order to view and cycle between multiple camera systems. When cycling, the current channel will be displayed on screen.

To determine a camera’s channel frequency, simply cycle through each of the four channels until a picture is displayed on screen. NOTE: Slight adjustments in your viewing angle can greatly affect the quality of the picture.

» Hard-wire Connection

The Handheld Monitor Pro provides a direct hard-wire connection to compatible camera systems. NOTE: When working in extreme low light environments hard-wire the HHM Pro to the camera system (if hard-wire option is available with the camera system). A hard-wire connection provides a slightly brighter picture on the monitor that will be beneficial for low light situations.


OPERATION AND SUPPORT PUBLICATIONPRO MONITOR OPTIONS 15

Power

Channel Selector

IR Toggle

Camera Toggle

Hard wire jack

OPERATION AND SUPPORT PUBLICATIONSPECIFICATIONS 16

©2013 Tactical Electronics and Military Supply, L.L.C. All Rights Reserved.Product specifications and information are subject to change without notice.

If you encounter any problems with your system, please contact us immediately:

Tactical ElectronicsP.O. Box 152Broken Arrow, OK 74013-0152(866) 541-7996

SPECIFICATIONS

TACTICALELECTRONICS.COM

PRODUCTS / EOD TRAINING / R & D / AVIATIONDESIGN / ENGINEERING / MANUFACTURING

HEMLOCK FACILITY

2200 NORTH HEMLOCK AVE / BROKEN ARROW, OK / 74012V: 866.541.7996 / V: 918.249.8326 / F: 918.249.8328

CRUSADER FACILITY

2844 CRUSADER CIRCLE / #100 / VIRGINIA BEACH, VA / 23453V: 757.689.0476 / F: 757.689.3769

CAMERAS: Forward and upward facing cameras

WEIGHT: 15.70oz

DIMENSIONS (L X W X H): 9.75in x 3.30in x 1.66in

POWER SUPPLY: Four 3V Lithium batteries (CR123A type)

RUNTIME: 1.25+ hours

HOUSING MATERIAL: High-density polyethylene (HDPE), anodized aluminum

OPERATING TEMPERATURE RANGE: -10ºC to +50ºC, 95% humidity

FREQUENCY RANGE: 2.4 to 2.485 Ghz (4 channel system)

TRANSMISSION DISTANCE: 100ft line of sight

COMPATIBLE MONITORS: Wrist Mounted Monitor Pro / Handheld Monitor Pro / Wrist Mounted Monitor / Handheld Monitor / Heads-Up Display / Monocular Micro Viewer

CAMERA RESOLUTION: 400 TV lines

CAMERA LIGHT SENSITIVITY: 0.005 lux

CAMERA SENSOR TYPE: Black and White Super-HAD CCD

ILLUMINATION: IR LED Flood Illuminator, 4 forward facing Directional IR LEDs

INSERTION PANEL: 0.262in thick

PANEL LENGTH: 6.0in long

HARD-WIRE VIDEO OUTPUT: 1/4 inch stereo jack

FIELD OF VIEW: FORWARD CAMERA 68.6° (H) and 47.4° (V)

FIELD OF VIEW: UPWARD CAMERA 46.26° (H) and 32.8° (V)

RECORDING SPECIFICATIONS:

STORAGE MEDIA: SDHC memory card (16GB SDHC card included with system)

RECORDING CAPACITY: 16 hours on 16GB SD card (1GB/hour)

UDC P RO - Tactical Electronics€¦ · One) Under Door Camera Pro (2-camera system) » Two...

Documents

Transcript of UDC P RO - Tactical Electronics€¦ · One) Under Door Camera Pro (2-camera system) » Two...