UCT Manual Hindi v1.0

UNIVERSAL CHINA TOOL POWERED BY ET

w w w . u tc . c c

English

www.uct.cc

UNIVERSAL CHINA TOOLUNIVERSAL CHINA TOOL

fgUnh

UCT Box Operation Manualv2.2

Website & Download Area : http://www.uct.ccSupport Forum : http://forum.uct.cc

For any further support please contact us as [email protected]

fdlh vU; lgk;rk vkSj tkudkjh ds fy, gesa bZesy djsa %& [email protected]

Index

English:

Software InstallationConnecting UCT Box & PhoneChecking UCT Box COM Port NumberUCT China Tool Software InterfaceMTK Handsets

Read Info for MTKFormat / Reset Phone for MTK

Touch Screen Calibration Bypass on MTKReading Full Flash / Full Backup of MTKWriting Full Flash / Full Restore of MTKRepair and Fix Bad Software of MTK

SpreadTrum (SPD) Handsets

Format / Reset Phone for SpreadTrum (SPD)Repair IMEI on SpreadTrum (SPD)

MStar CPU HandsetsInfineon Handsets: Writing FlashErasing Full Flash of Chinese HandsetsUpGrading UCT Box FirmwareHow to Fix “Conjunction Box Error” while UpGrading

IMEI Repair on MTKIMEI Repair using Tracker on MTK

Solve “ProjectID Not Found”

About SpreadTrum (SPD)Read Info from SpreadTrum (SPD)Read Flash from SpreadTrum (SPD)

Write Flash for SpreadTrum (SPD)

Trouble-ShootingUsing UCT Box as Pin Finder for Other SoftwareGeneral Problems & There SolutionsProblem with Anti-Virus Software’s in InstallationUCT Fusion Software

UCT Box Self CheckingAuto-Detect CPU TypeFinding Pinouts for MTK 2nd CPUPinout Defining

..............................................................................................3..........................................................................4

.........................................................5..................................................................6

.......................................................................................................7..................................................................................7

...........................................................8...............................................................................9

...................................................10......................................11

..........................................12.........................................12

...............................................12.............................................................13

...........................................................................14....................................................................14

....................................................15.................................................16

................................17...................................................18...................................................19

.........................................................................................20......................................................................21

..........................................................22......................................................................23

...........................24.................................................................................................25

......................................27.............................................................28

......................................31.........................................................................................32

......................................................................32.......................................................................33

...................................................33......................................................................................34

Why UCT Box?

With UCT, you can now do a lot extra with chinese phones. Repair all sort of

problems, like blinking, dead, full flashing, easy 1 click reset, IMEI Repair, Touch

Screen Caliberation, Fastest & most accurate pinfinding, SpreadTrum support (no

extra hardware needed) and much-much more. Also New UCT has ability to self

test the box and report errors in case of any malfunctioning. Most economically

designed with the latest technology makes it cheapest in the market for Chinese

Phones Automatic Pinout Finding, but it doesn't means it has less features. The best

not need be the costliest. Right?

MediaTeK (MTK):* Read Information about phone

* Read / Write full flash

* Format FFS / Reset phone

* Repair "Bad Software"

* Repair Sim Lock w/o Formatting

* Repair & Write IMEI for Sim1, Sim2

* Read / Write / Edit Phone Book

* Touch Screen Calibration Bypass

* Repair and Backup NV Items

* Fix Informality Software

* Many more...

SpreadTrum (SPD):* Read Information about phone



* Unlock Phone

* Repair & Write IMEI

SkyWorks:* Read / Write full flash

Qualcomm:* Read Information

* Backup / Restore NV Data

* Full NV Editor

* File System Explorer

* Reset / Read Unlock Code

* Simulate Keypad

MStar:* Read Information


* Read Security / Unlock Code

Analog Devices (ADI):* Read / Write full flash

NXP (Philips):* Read Information about phone


SiliconLabs:* Read Information about phone



* Unlock Phone

MSW:* Read Information about phone


Anyka:* Read Information about phone


* Unlock Phone

Infineon:* Read / Write full flash

* Decrypt File for edit UNIVERSAL CHINA TOOL POWERED BY ET

w w w . u tc . c c


w w w . u tc . c c

Software Installation

1. To install UCT Box software, you need to copy the latest setup file from dvd or

download from support area.

2. Run the setup file, follow the setup instructions and complete the procedure.

3. After installing setup, you need to install the drivers. Go to "Start" Menu, "All

Programs", "UCT Team", "Install UCT Box Drivers".

This will auto-install the drivers for UCT Box.

Now connect the UCT Box to your computers USB port. The computer with install

the drivers

automatically, but if in any case it cannot, then you can specify the location for the

drivers inside "C:\UCT\UCT Drivers\".

;w0lh0Vh0 lks¶Vos;j dk bUlVksys”ku

1- lks¶Vos;j bULVky djus ds fy, lcls igys ysVsLV otZu ds lSV vi Qkby dks Mh0oh0Mh0 ls dkih dj ysa ;k fQj osclkbV ls Mkmu yksM dj ysA

2- vc bl lsVvi Qkby dks ju djsa vkSj tSlk dgk tk, oSlk djsA3- bULVky [kRe gksus ds ckn ;w0lh0Vh0 MªkbolZ dks bULVky djsaA

blds fy, “Start” ehuw esa “All Program” ds vUnj fQj “UCT Team”

QksYMj esa tk, vkSj “Install UCT Box Drivers” dks pyk,A

vc vkids dEI;wVj esa ;w0lh0Vh0 ckDl dk lks¶Vos;j iwjh rjg ls bULVky gks pqdk gSA vc vki ckWDl dks dusDV dj ldrs gSA dEI;wVj vius vki gh MªkbolZ fMVsDV dj ysxkA vxj ,slk u gks rks vki “C\UCT\UCT Drivers\” QksYMj ls mUgsa bULVky dj ldrs gSA

Page. 3


w w w . u tc . c c

Connecting the UCT Box and the Phone

1. Connect the UCT Box to PC USB Port2. Your computer will ask for box drivers. Drivers can be found inside your UCT Installation folder “C:\UCT\UCT Drivers” and also are located in DVD supplied with UCT in folder “UCT Drivers”.3. Connect Main Cable to the "24-Pin Intelligent connector" from the side where power leads are coming out.4. Connect the corresponding connector to the main cable.5. Connect the Power leads to the phone battery connector & the PCB connector to the phone socket.

;w0lh0Vh0 ckWDl vkSj gs.MlsV dks tksMs+a

1- UCT Box dks USB Cable ls tksM+saA2- dscy tksM+rs gh dEI;wVj Mªkboj dh ekax djsaxkA ;g Mªkboj UCT

Box dh DVD ds vUnj miyC/k gSA 3- esu dsfcy dks ̂ ^24 fiu baVsyhtsaV duSDVj** ls tksM+sa ftl rjQ ls

ikoj dh rkj fudyh gqbZ gSaA4- ikoj dh rkjksa dks cSVjh duSDVj ls tksM+sa vkSj Qksu dh rkjksa dks Qksu

duSDVj ls tksM+saA

Page. 4


w w w . u tc . c c

Checking UCT Box Com Port Number:

1. Right Click on “My Computer” and then select “Properties”, after thick click on “Hardware” tab and then press “Device Manager”. Here you can see information about all the devices you have connected with your computer.

2. Now go to the “Ports (Com & LPT)” and here you will see “USB Serial Port (COMxx)”, here xx is your Com port number.

UCT Box dk dkWe iksVZ uEcj

ckWDl dusDV djus ls igys vkidks ;g ns[kuk iM+sxk fd ;w0lh0Vh0 ckWDl dkSu ls dkWe iksVZ ij bUlVksYM gSA bldh tkudkjh ds fy,

1- ^^ekbZ dEI;wVj** ij jkbV fDyd djsa vkSj ^^Properties** esa tkdj “hardware” dks fDyd djsaA ;gk¡ ”Device Manager” esa lHkh fMokblst dh tkudkjh ns[kh tk ldrh gSA

2- blesa “Port (Comm and LPT)” dks fDyd djsaA blesa ns[ksa ”USB

Serial Port (Com xx)” ;gk¡ xx vkids Com port dk uEcj gSA

Page. 5


w w w . u tc . c c


w w w . u tc . c c

UCT ET China Tool Interface

Read Info: This is used to read handset information, like:# Mobile Software Project ID# CPU Type# Flash Type & Size

Read Flash: Read full backup flash file of the handset

Write Flash: Flash the handset with the provided flash file

Format: Reset the handset to Full factory settings, Unlock, Repair Blink

Tracker: Read Unlock code, Repair Touchscreen, Repair IMEI, Repair Bluetooth, Edit PhoneBook

IMEI: Repair IMEI of handset

Decryption: Fix and repair “Bad Software” problems

NV: NV-RAM Editor for MTK (Advanced Users)

Port: Select Comm Port number of the UCT Box (check the comm port your UCT is installed using the device manager)

Baud: Select the baudrate to communicate with the handset (Slower is better)

Auto Sense: Auto-Find the Pinouts of the handset on every operation if selected (you can uncheck this if you are working on 1 type handset only, means no need to find pinout everytime)

Connect: Connect the UCT Box using the specified comm port number.

Page. 6


w w w . u tc . c c


w w w . u tc . c c

Operations for MTK Handsets:

Read Info from MTK Handset:

1. Go to “MTK” Tab, select “ReadInfo”, select “Baud” as 921600, check “Auto-Sense” and press “Start”.

2. As soon as you press start, keep & hold pressing the “Power ON” button on the handset. Leave the power on button after red bar is at 100%.

3. After process is done you can see all information at the bottom.

MTK gs.MlsV

pkbZfut Qksu dbZ izdkj ds vkrs gSaA buesas ls 90 izfr'kr ,e0Vh0ds0 ds gksrs gSaA ,e0Vh0ds0 ds lSV dks duSDV djus ds fy,

1- MTK Vsc ij tk;sa] ”Read Info” flysDV djsa] ”Baud 921600” djsa ”Auto sense” dks fDyd djsa] fQj LVkVZ dks fDyd djsaA

2- tSls gh LVkVZ dks fDyd djsa mlds ckn Qksu ds ikoj vkWu cVu dks nck;sa j[ksa tc rd jsM ckj 100 izfr”kr u gks tk;sA

3- 100 izfr”kr gksrs gh vkids gs.MlsV dh tkudkjh uhps LØhu ij vk tk;sxhA

dh tkudkjh

Page. 7


w w w . u tc . c c


w w w . u tc . c c

Format / Reset Phone for MTK Handset:

1. Take “IMEI”, “Touch screen Calibration” & Full backup of handset using the “Tracker” for safety.

2. Go to “MTK” Tab, select “Format”, check “Auto Format”, check “Auto-Sense” and press “Start”.


4. After green bar go 100% your phone is format and ready. You can now repair the IMEI from Tracker Option.

MTK QkWesZV@fjlsV gs.MlsV

pkbZfut gS.MlSV esa dbZ [kjkc;k¡ mudks QkWjesV ;k fQj jhlsV djds lgh djh tk ldrh gSA

1- gs.MlsV dh lqj{kk ds fy;s ”Tracker” }kjk IMEI vkSj Vp LØhu dsyhczs”ku dk csd vi ys ysaA

2- ”MTK Tab ij tk;sa] Format fDyd djsa vkSj Autoformat

flysDV djsaA blds ckn ”Autosense” flysDV djsa vkSj ”Start” nck;saA


4- xzhu ckj ds 100 izfr”kr gksrs gh gekjk gs.MlsV QkesZV gks pqdk gSA vc Vsªdj }kjk IMEI fjis;j dj ysaA

” ” ” ” ”

Page. 8


w w w . u tc . c c


w w w . u tc . c c

IMEI Repair on MTK Handset: (Method 1)

1. Go to “MTK” Tab, select “IMEI”, select “META” or “AT” (try META if AT not works for you)

2. Enter the new and correct 15 digit IMEI of the handset in the “IMEI 1” block, if handset is dual sim and you need to fix the second IMEI also, then enter the second IMEI in the “IMEI 2” block. Press “Start”

3. As soon as you press start, keep & hold pressing the “Power ON” button on the handset. Leave the power on button after the operation is done.

Your handset is now fixed with new IMEI. If you get any error in this procedure then try to first format the handset and then again try to fix IMEI.

If still have error then you can fix the IMEI using method 2 using the “tracker” Option.

,e0Vh0ds0 gSaMlsV dk vkbZ0,e0bZ0vkbZ0 fjis;j djuk

1- ,e0Vh0ds0 ds Vsc ij tk, vkSj vkbZ0,e0bZ0vkbZ0 flysDV djsaA2- vius Qksu ds lgh vkSj genuine vkbZ0,e0bZ0vkbZ0 ds iUnzg fMftV

dks “IMEI 1” Cykd esa MkysaA ;fn vkidk Qksu nks fle okyk gS rks mldk nwljk vkbZ0,e0bZ0vkbZ0 “IMEI 2” Cykd esa Mkys vkSj LVkVZ nck,A

3- tSls gh LVkZV dks fDyd djsa mlds ckn Qksu ds ikoj vksu cVu dks nck;sa j[ks tc rd vkbZ0,e0bZ0vkbZ0 fjis;j iwjk u gks tk,A

vc vkids gSaMlsV dk vkbZ0,e0bZ0vkbZ0 fjis;j gks pqdk gSA ;fn vkidks blesa vlQyrk feys rks vki Qksu dks QkjesV djs vkSj fQj ls vkbZ0,e0bZ0vkbZ0 fjis;j VªkbZ djsaA

vxj fQj Hkh vkbZ0,e0bZ0vkbZ0 fjis;j uk gks] rks “Tracker”

}kjk vkbZ0,e0bZ0vkbZ0 fjis;j djs tks fd Method 2 esa crk;k x;k gSA

Page. 9


w w w . u tc . c c

IMEI Repair on MTK Handset using Tracker: (method 2)

1. Go to “MTK” Tab, select “Tracker”, check “Auto-Sense” and press “Start”.


3. Now you can see the “MNR Tracker” window. Here go to “IMEI” Tab & fill in the correct IMEI of the handset in “IMEI 1”. If your handset is dual sim and dual IMEI, then enter the second IMEI in the “IMEI 2” box. Check “Modify” & “Auto checksum” and then press “Write”.

4. After bar goes 100% close the window. IMEI has now been repaired on your handset.

MTK - gs.MlsV

pkbZfut gS.MlSV dks QkWjesV] fjis;j] fjlsV ;k fQj ¶yS'k djus ds dkj.k mudk vkbZ0,e0bZ0vkbZ0 [kjkc gks tkrk gSA blfy, ;g cgqr t:jh gS fd mudk vkWfjtuy o tSU;wvu vkbZ0,e0bZ0vkbZ0 okfil jkbZV dj fn;k tk,A

1. MTK tab ij tk;sa vkSj racker flysDV djsa] utosense dks flysDV djds ”Start” nck;saA


3- 100 izfr”kr gksus ds ckn ”MNR Tracker” esa tkdj IMEI flysDV djsaA ;gk¡ ij vius gs.MlsV dk lgh vkSj tsuqvu IMEI uEcj MkysaA vxj vkidk gs.MlsV nks fle okyk gS rks nwljk IMEI Hkh Mkysa vkSj ”Modify” fDyd djsaA

4. ”Autochecksum” fDyd djds] ”Write” fDyd djsaA5- tc ckj 100 izfr”kr gks tk;s rks vkids gs.MlsV dk IMEI fjis;j gks

pqdk gSA

IMEI fjis;j

” ” ”T ” ”A ”

Page. 10


w w w . u tc . c c


w w w . u tc . c c

Touch Screen Calibration Bypass on MTK Handset:

1. Go to “MTK” Tab, select “Tracker”, check “Auto-Sense” and press “Start”.


3. Now you can see the “MNR Tracker” window. Here go to “Restore Settings” tab, check “TouchScreen calibration data” & then press “Restore”.

4. Software will now ask location for file, load the file “UCT_Touch.cci” which is available inside “TouchScreen Data” folder.

5. After bar goes 100% a warning will come, press “OK” and close the window. Touch Screen Calibration Bypass has been done.

,e0Vh0ds0 gS.MlSV : Vp LØhu dSfyfcjs'ku ckbZ&ikl

;fn Vp LØhu [kjkc gs vkSj gS.MlSV 'kq:vkr esa dSfyfcjs'ku ekaxrk gS rks vki gS.MlSV bLrseky ugha dj ikrs gSA exj ;w0lh0Vh0 ds bl Qhpj ds iz;ksx ls vki dSfyfcjs'ku dks ckbZ&ikl dj ldrs gSa vkSj gS.MlSV bLrseky dj ldrs gSaa

1. MTK” tab ij tk;sa vkSj racker flysDV djsa] utosense dks flysDV djds ”Start” nck;saA


3- 100 izfr”kr gksus ds ckn ”MNR Tracker” esa tkdj ”Restore

settings” flysDV djsaA blds ckn ”Restore” nck;saA 4- blls lkW¶Vos;j fjLVksj Qkby dh ekax djsaxkA ;g Qkby

Mh0oh0Mh0 esa VpLØhu MkVk uke ds QksYMj esa gSA Qkby dk uke gS ”uct_touch.cci”A

5- tc ckj 100 izfr”kr gks tk;s rks ”OK” dks flysDV djsa vkSj foUMks dks cUn dj nsaA vc vkids gs.MlsV dk Touchscreen Calibration

Bypass gks pqdk gSA

” ”T ” ”A ”

Page. 11


w w w . u tc . c c

Reading Full Flash / Full Backup of MTK Handset:

1. Go to “MTK” Tab, select “Readback”, press “…” and select the location and filename of the readback file. Then check “Auto-Sense” and press “Start”.


3. Software will now read the flash file and save it to the specified location automatically.

Writing Full Flash / Full Restore of MTK Handset:


2. Go to “MTK” Tab, select “Download”, press “…” and select the location and filename of the file to write to the phone. Then check “Auto-Sense” and press “Start”.


4. Software will now write the flash file.

Repair and Fix “Bad Software” of MTK Handset:


2. Go to “MTK” Tab, select “Decryption”, select “Bad Software_1” or “Bad Software_2”, press “…” and select the location and filename of the file to write to the phone. Then check “Auto-Sense” and press “Start”.


4. Software will now write the flash file and repair “Bad Software” problem.

,e0Vh0ds0 gS.MlSV : QySl QkbZy jhM

1- “MTK tab ij tk;sa Readback flysDV djsaA 2. “…” dks fDyd djsa vkSj jhM dh xbZ QkbZy dk uke vkSj yksds”ku

nsaA 3. “Autosense“ flysDV djsa vkSj “Start“ nck;saA 4- tSls gh LVkVZ dks fDyd djsa mlds ckn Qksu ds ikoj vkWu cVu dks

nck;sa j[ksa tc rd jsM ckj 100 izfr”kr u gks tk;sA5- blds ckn lkW¶Vos;j Qkby jhM djuh “kq# djsxk vkSj crkbZ xbZ

txg ij lso dj nsxkA

,e0Vh0ds0 gS.MlSV :

1- lqj{kk ds fy;s “Tracker“ }kjk “IMEI“ vkSj “Tourchscreen

calibration“ dk csdvi ysysaA 2. “MTK“ tab ij tk;sa vkSj “Download“ fDyd dj] ̂^---** dks fDyd

djsa vkSj Qkby dh yksds”ku vkSj uke crk;saA3. “Autosense“ fDyd djsa vkSj “Start“ nck;sa A4- tSls gh LVkVZ dks fDyd djsa mlds ckn Qksu ds ikoj vkWu cVu dks

nck;sa j[ksa tc rd jsM ckj 100 izfr”kr u gks tk;sA5- lkW¶Vos;j vc Qkby jkbV djuh “kq# dj nsxkA

,e0Vh0ds0 gS.MlSV : cSM lks¶Vos;j fjis;j

1- gs.MlsV dh Qqy ¶yS”k jhM dj ysaA 2. “MTK“ tab ij tk;sa vkSj “Decryption“ flysDV djsaA3. “Bad software 1“ vkSj “Bad software 2“ dks fDyd djsa] ̂ ^---** dks

fDyd djsa vkSj jhM dh xbZ Qkby dh yksds”ku vkSj uke crk;saA 4. “Autosense“ fDyd djsa vkSj “Start“ nck;saA5- tSls gh LVkVZ dks fDyd djsa mlds ckn Qksu ds ikoj vkWu cVu dks

nck;sa j[ksa tc rd jsM ckj 100 izfr”kr u gks tk;sA6- lkW¶Vos;j vc Qkby jkbV djsxk ftlds ckn vkids gs.MlsV dh

leL;k nwj gks tk;sxhA

“ “

¶yS”k Qkby jkbV

Page. 12


w w w . u tc . c c

How to solve error: "ProjectID Not Found”

Some MTK CPU based handsets show error "ProjectID Not Found" when tried to connect or read info. This is usually found in CPU ID 6235 based handsets or we can say is found in handsets which have "NAND" memory inside. To fix this, please follow:

1. Select "MTK" Tab, "select desired operation.2. In Options, select Mode as "NAND" and Boot version as “Ver3.952"3. Now press "Start", all should go smooth and normal.

If you are still not able to connect the handset, then you can try with different versions.

“Project ID Not Found” dk lek/kku

dqN ,e0Vh0ds0 gSaMlsV dusDV djus ij “Project ID Not Found” dk ,jj nsrs gSA bl ,jj dk vf/kdrj dkj.k gS xyr cwV Vkbi ij mudks dusDV djukA ;g vf/kdrj #i ls ,e0Vh0ds0 6235, 6238, 6228 esa gh vkrk gSA cfYd ;w dgk¡ tk, fd Nand ¶ys”k eSeksjh okys gSMlsV esa ;g ,jj vkrk gSA

1- ,e0Vh0ds0 Vsc ij tkds viuk vkWijs”ku flysDV djsA 2- vki”ku esa eksM ij “Nor” dh txg “Nand” flysDV dj ys vkSj cwV

otZu esa “Ver3.925” flysDV dj ysA3- vc LVkZV fDyd djds vius gSaMlsV dks dusDV dj ldrs gSA

;fn vHkh Hkh dksbZ leL;k vk, rks vki cwV otZu dks cnyds dksf”k”k dj ldrs gSA

Page. 13


w w w . u tc . c c


w w w . u tc . c c

Difference Between SpreadTrum & MTK handsets

Most of the handsets available in market are based on MTK CPU. The other most important CPU available in market after MTK is SpreadTrum CPU. These CPU are totally different in working and in repairing procedure. Unlike MTK, these can only be repaired by USB connectivity. which is why pinout finding procedure is totally different and unique for them.

SpreadTrum (SPD) Handsets:

About Different Boot Mode:

SpreadTrum CPU have different boot mode according to there CPU Type. Which is why it is important to select the correct boot mode for proper connectivity with the software. It might be posible that you can read info and flash with wrong selection, but for write flash need to select correct boot mode.

Correct Steps to connect a SpreadTrum based handset:

1. First you need to “ReadInfo” of the handset. If you don't know the CPU boot type then you can try “Auto-USB”, “Auto-COM”, “6600L-USB” or “6600L-COM” one-by-one.

2. After you have read the information of the handset, you can read in it that which type is the CPU and flash memory of the handset.

Example: CPU: SC6600E-xxxx Flash: NAND_xxxx

Here the CPU type is 6600E and the memory type in NAND, so in this case you need to select the option “6600M/E/I-NAND” and then proceed further.

3. After you have selected the correct CPU type in the options, now you can start with Format, Read Flash, Write Flash, Repair IMEI, etc.

LçsMVªe gSaMlsV esa ;g vko”;d gS fd vki”ku esa lgh cwV eksM dks flysDV fd;k tk,A xyr eksM flysDV djus ls gSaMlsV lgh çdkj ls fMVsDV ugha dj ik,xkA

gks ldrk gS fd gSaMlsV jhMbUQks dj ys exj ¶ys”k jkbV djus ds fy, lgh cwV eksM vki”ku esa flysDV djuk vko”;d gSA

LçsMVªe gSaMlsV dks dusDV djus ds lgh LVsIl %

1- lcls igys “Read Info” ysA vxj vkidks lh0ih0;w0 Vkbi ugh irk gS rks vki “Auto-USB”, “Auto-Com”, “6600L-NOR” dks ckjh&ckjh dksf”k”k dj ysA

2- bUQks vkus ds ckn vki tku ldrs gS fd gSaMlsV dk lgh cwV eksM dkSu lk gS] vc ;gh eksM vki”ku esa flysDV dj ysA

3- vc vki ¶ys”k jhM ;k jkbV vkSj QkjesV dj ldrs gSA

;fn “Auto-USB” vki”ku ls fiu vkmV Qkb.M u gks rks vki “Auto-Com” ;k fQj “6600L-NOR” dks ckjh&ckjh dksf”k”k dj ysaA

Page. 14


w w w . u tc . c c

Operations for SpreadTrum (SPD) Handsets:

Read Info from SpreadTrum (SPD) Handset:

1. Go to “SpreadTrum” tab, select “ReadInfo”, select option according to CPU type, check “Auto-Sense” & Press “Start”.

2. Now you don't need to power on the phone in SPD handsets. It will automatically start sensing the pinouts. After finding the pinouts the phone will ask for usb drivers. SPD drivers are located under folder “SpreadTrum_USB_Driver”. If you have already installed the drivers then system will not ask for drivers next time.

3. After installing drivers, software will connect to your SpreadTrum handset and will read information which will be displayed on the bottom.

Spread Trum Handset (SPD) dh tkudkjh

,e0Vh0ds0 ds vykok pkbZfut gS.MlSV vf/kdrj LiSMVªe lh0ih0;w0 ds gksrs gSaA ;g lh0ih0;w0 ;w0lh0Vh0 }kjk fjis;j fd;s tk ldrs gSaA

1- Spread Trum tab ij tk;sa vkSj ead Info flysDV djsaA mlds ckn ”Autosense” fDyd djds ”Start” nck;saA

2- ”Spread Trum” gs.MlsV esa gesa ikoj vkWu cVu nckus dh dksbZ Hkh vko”;drk ugh gSA ;g vius vki gh sense djuk “kq# dj nsxkA

3- Sense djus ds ckn lkW¶Vos;j ;w0,l0ch0 Mªkboj ekaxsxkA ;g Mªkboj Mh0oh0Mh0 ”Spread Trum USB Driver” ds QksYMj esa gSA

4- MªkbolZ nsrs gh lkW¶Vos;j gs.MlsV dh tkudkjh uhps fn[kk;sxkA

” ” ”R ”

Page. 15


w w w . u tc . c c

Read Flash for SpreadTrum (SPD) Handsets:

1. Go to “SpreadTrum” tab, select “Read Flash”, select flash file path.2. Select the CPU type from the drop down list in the “Options”. (You

can detect your CPU type by reading info or by opening the handset)3. Check “Auto-Sense” & Press “Start”.4. After f inding pinouts software wil l ask for drivers

“SpreadTrum_USB_Driver”.5. As soon as drivers are installed, software will read the flash file from

the handset and save it to the specified location.

LçsMVªe gSaMlsV dh ¶ys”k Qkby jhfMax %

1- LçsMVªe Vsc ij tk, vkSj jhM ¶ys”k flysDV djsA ¶ys”k Qkby lso djus dk ikFk flysDV djsA

2- vc vius gSaMlsV dk lgh cwV Vkbi vki”ku }kjk flysDV djsA3- LVkVZ nck,A4- LçsMVªe gSaMlsV ds fiu vkmV Qkb.M djus ds ckn dEI;wVj vkils

;w0,l0ch0 MªkbolZ ekaxsxkA LçsMVªe ;w0,l0ch0 MªkbolZ “C:\UCT\Spreadtrum_USB_Drivers\” QksYMj ds vUnj miyC/k gSA

5- MªkbolZ bULVky gksrs gh ;w0lh0Vh0 lks¶Vos;j ¶ys”k Qkby dks jhM djuk “kq: dj nsxkA

Page. 16


w w w . u tc . c c


w w w . u tc . c c

Format / Reset Phone for SpreadTrum (SPD) Handsets:

1. Take full backup of the handset using “Readback” feature for safety.2. Go to “SpreadTrum” tab, select “Format”, select option for CPU boot

type, check “Auto Format”, check “Auto-Sense” & Press “Start”.3. After f inding pinouts software wil l ask for drivers

“SpreadTrum_USB_Driver”.4. As soon as drivers installed, software will format the handset in few

seconds.

Spread Trum QkWesZV@fjlsV gs.MlsV

1- lqj{kk ds fy;s gs.MlsV dk Qqy csdvi jhM dj ysaA 2- Spreadtrum tab ij tk;sa vkSj Format flysDV djsaA mlds

ckn ”Factory Set” dks fDyd djsa vkSj ”Start” nck;saA 3- Sense djus ds ckn gs.MlsV Mªkboj ekaxsxkA4- Mªkboj bUlVky gksus ds ckn lkW¶Vos;j rqjUr gh gs.MlsV dks

format dj nsxkA

(SPD)

” ” ” ”

Page. 17


w w w . u tc . c c


w w w . u tc . c c

Repair IMEI on SpreadTrum (SPD) Handsets:

1. Take full backup of handset using the “Readback” feature.2. Go to “SpreadTrum” tab, select “IMEI”, enter the new IMEI in “New

IMEI Code” box and the existing IMEI in the handset in “Original IMEI” box.

3. Select the readed flash file in step 1 in the file location and then press “Start”.

4. Now a new file has been created in the same folder with new name ending with new IMEI. Just flash this new file to the handset using the “Download” feature.

5. Your phone now has the new and repaired IMEI.

LizsMVªe gS.MlSV ds vkbZ0,e0bZ0vkbZ0 fjis;j

1- gs.MlsV dk Qqy csdvi jhM dj ysaA 2. “Spreadtrum tab ij tk;sa vkSj IMEI flysDV djsaA mlds ckn

“New IMEI“ esa u;k o genuine IMEI Mkysa vkSj “Original IMEI“

esa gs.MlsV dk iqjkuk IMEI MkysaA 3. “Open“ dks fDyd djsa vkSj jhM dh x;h QkbZy dks flysDV djsaA

blds ckn “Start“ fDyd djsaA 4- blds ckn u;s IMEI uEcj ds uke ls mlh QksYMj esa ,d ¶yS”k

Qkby cu tk;sxhA bl QkbZy dks gs.MlsV esa write djsaA 5- bl Qkby ds flash gksrs gh vkids gs.MlsV esa u;k IMEI vk

tk;sxkA

“ “ “

Page. 18


w w w . u tc . c c


w w w . u tc . c c

Write Flash for SpreadTrum (SPD) Handsets:

1. Go to “SpreadTrum” tab, select “Write Flash”, select the Flash file to be flashed.

2. Select the CPU type from the drop down list in the “Options”. (You can detect your CPU type by reading info or by opening the handset)

3. Check “Auto-Sense” & Press “Start”.4. After f inding pinouts software wil l ask for drivers

“SpreadTrum_USB_Driver”.5. As soon as drivers are installed, software will start flashing the

handset.

LçsMVªe gSaMlsV dh ¶ysf”kax %

1- LçsMVªe Vsc ij tk, vkSj jkbV ¶ys”k flysDV djsA ¶ys”k djus okyh Qkby dks flysDV dj ysA

2- vc vius gSaMlsV ds lgh cwV Vkbi vki”ku }kjk flysDV djsA ;g cgqr vko”;d gSA

3- LVkVZ nck,A4- LçsMVªe gSaMlsV ds fiu vkmV Qkb.M djus ds ckn dEI;wVj vkils

;w0,l0ch0 MªkbolZ ekaxsxkA5- MªkbolZ bULVky gksrs gh ;w0lh0Vh0 lks¶Vos;j ¶ysf”kax “kq: dj

nsxkA

Page. 19


w w w . u tc . c c

MStar CPU Handsets:

To connect MStar PCU handsets you will need USB drivers for these phones. These USB drivers can be download now from UCT Box support area.

1. First u need to read information of the handset. Go to “MStar” tab, select “ReadInfo”, select option according to CPU type. If you don't know the CPU boot type then you can try "B1" and "B2" one-by-one.

2. Press “Start”. 3. Now you don't need to power on the phone in MStar handsets. It will

automatically start sensing the pinouts. After finding the pinouts the phone will ask for usb drivers. MStar USB drivers are located under folder “MStar_USB_Driver” or can download from support area. If you have already installed the drivers then system will not ask for drivers next time.

4. After installing drivers, software will connect to your MStar handset and will read information which will be displayed on the bottom.

5. You can now read in it that which type is the CPU and flash memory of the handset and then proceed further by selecting appropriate in the options.

6. After you have selected the correct CPU type in the options, now you can start with Read Flash, Write Flash, Read Security Code, etc.

Page. 20


w w w . u tc . c c


w w w . u tc . c c

How to Read Security Code in MStar Phones:

UCT Box can read the security code from MStar based phones, but for this you first need to read the flash file and read the security code using the flash file.

1. Read the full flash file of the handset by using the “Read Flash” feature and save it to your hard disc.

2. Now select “Read SecCode in file” and select the readed flash file.3. Press “Start” and UCT software will find and read out the codes in the

handset.

Infineon Handsets: Writing Flash

1. Go to “Infineon” Tab, select “Write Flash” & click the “...” to select the flash file to write to the phone.

2. After specifying the location and filename, select “Baud” as 921600, check “Auto-Sense” and press “Start”.


4. After process is done your phone is flashed with the new firmware.

Infineon :

ckdh lc lh0ih0;w0 dh rjg] bUkfQfu;u lh0ih0;w0 ij cus gSaMlsV dh Hkh fiu vkmV QkbfUMax vkSj ¶ys”k jhM jkbV djh tk ldrh gSA blds fy, %

1- bUkfQfuf;u Vsc ij tk,] jkbV ¶ys”k flysDV djs] ¶ys”k djus okyh Qkby dks flysDV djsA

2- vc vksVks lsULk flysDV djds LVkVZ nck,A3- LVkVZ nckrs gh Qksu ds ikoj vkssu cVu dks nck, j[ksA tc rd

¶ysf”kax “kq: u gks tk,A4- ¶ysf”kax “kq: gksrs gh ikoj vksu cVu NksM+ nsA FkksM+h gh nsj esa gSaMlsV

¶ys”k gks tk,xkA

Page. 21


w w w . u tc . c c


w w w . u tc . c c

Erasing Full Flash of Chinese Handsets:

Q. First, most important, why do we need to full erase?A. Sometimes writting flash files to chinese phones is a big problem.

Even if u get everything ok, it might still give error at some percentage. Sometimes stuck at 10%, sometimes stuck at 15%. As per my personal experience, Full erasing has always been useful before flashing in such problems. Either that be chinese phones or be nukia phones :)

Step-by-Step Guide on how to erase full flash of your Chinese handset:

1. Read the Information of the handset (Also read full flash backup of handset in case u need it in future)

2. At the bottom of the information read, you can notice how much size is your flash chip. like in our example SpreadTrum handset, its 64mb

3. Now select "Format", Uncheck "Auto Format"4. Enter the hex size "0x04000000" in the "Size" field,

(Leave the Start field as it is)5. Press Start and your phone will be full erased in few seconds.

Now most important is to put correct size for formatting.Depending on your flash size you need to enter the correct format

size, the details are as follows:

* If your Flash is 4mb, then enter format size = 0x00400000 for Full Erase* If your Flash is 8mb, then enter format size = 0x00800000 for Full Erase* If your Flash is 16mb, then enter format size = 0x01000000 for Full Erase* If your Flash is 32mb, then enter format size = 0x02000000 for Full Erase* If your Flash is 64mb, then enter format size = 0x04000000 for Full Erase

Page. 22


w w w . u tc . c c


w w w . u tc . c c

UpGrading UCT Box Firmware:

Q. Why do we need to upgrade the firmware of the UCT Box?A. All the commands for Automatic Pinout Finding are stored inside

the UCT Box itself. Means the box is intelligent on its own to scan the pinouts and define them. Now these commands are often updated with new and faster routines, or maybe added support for new type CPU or also can be due to minor improvements. Thus, the latest version inside the UCT Box ensures faster and proper working.

Step-by-Step Guide on how to UpGrade the firmware inside UCT Box:

1. To Update the Box Firmware, download the latest setup from the support area and install it.

2. Go to "Start", "All Programs", "UCT Team". Open the "UCT Firmware Update x.xx". (If you dont have icons in your programs menu, then u can go to "C:\UCT|\UCT Firmware Update" folder and start from there)

3. Press "ScanPort" and then select the box comm port in the "Setup Port" list.

4. Now press "UpGrade-BOX". If all is well then your box will be upgraded with latest firmware in few seconds.

Important:

* Please make sure that you have not connected any handset when the UCT Box is being upgraded.

* Don’t power off the PC or diconnect box while the Box is being upgraded.

* Even if something goes wrong, then let the upgrade bar complete and then try again to upgrade.

Page. 23


w w w . u tc . c c

Solving the “Conjunction Box Error” Problem while upgrading UCT Box:

You may get "Conjunction Box Error" error while upgrading the firmware of your UCT Box. This can be due to many reasons. Can be due to incomplete upgrade of firmware, bad voltage spikes can corrupt the firmware inside UCT Box, can be due to some bugs too. But this can be solved easy with the UCT Box Fiwmare UpGrade Utility.

Step-by-Step guide on how to fix “Conjunction Box Error” when UpGrade the firmware inside UCT Box:

1. Disconnect UCT Box from USB, connect the main cable to UCT Box.

2. Now short the "+" and "-" wires of the main cable3. Connect computer with USB to UCT Box.4. Open the latest Update software for UCT Box. Press "ScanPort",

Select your UCT Box comm port number, tick the "Exigency UpGrade" and press "UpGrade-BOX"

All should be ok now. If still any problem, then try repeat this procedure 2-3 times. If still not help, then your box have a hardware problem, please contact your reseller.

Important:

* Please make sure that you have not connected any handset when the UCT Box is being upgraded.

* Don’t power off the PC or diconnect box while the Box is being upgraded.

* Even if something goes wrong, then let the upgrade bar complete and then try again to upgrade.

Page. 24


w w w . u tc . c c

Vªcy lwV ¼leL;k dk lek/kku½

iz'u %& gS.M lSV QkWjesV ;k QySl djus ds ckn [kjkc Vp LØhu ds dkj.k Qksu dke ugha djrk vkSj LVkVZvi iss dSfyfcjs'ku ds fy, :dk jgrk gSA mRrj %& Qksu QkWjesV ;k QySl djus ls igys csgrj gS fd vki ml Qksu dk

vkbZ,e0bZ0vkbZ0 vkSj Vp LØhu MkVk dk csdvi ys ysaA QySl ;k QkWjesV djus ds

ckn ;g cSd vi Qksu ij jkbZV dj nsaA ;fn vkius cSdvi ugha fy;k rks Hkh vki

;w0lh0Vh0 ds Vp LØhu dSfyfcjs'ku ckbZ&ikl Qhpj dh lgk;rk ls bldks

ckbZ&ikl dj ldrs gSaaA

iz'u %& ;w0lh0Vh0 gS.MlSV ds fiuvkmV ugha <¡w< ik jgk gS vkSj ,jj nsrk gS ^^lSUl Qsfy;j**mRrj %& ;fn vkidk Qksu ,e0Vh0ds0 ij dusDV ugha gks ik jgk gS rks fQj mldks

vyx& vyx lh0ih;w0 ij duSDV djus dh dksf'k'k djsaA vf/kdrj Qksu ,e0Vh0ds0

gksrs gSaA

iz'u %&D;k ;w0lh0Vh0 ckWDl dks vixzsM fd;k tk ldrk gS \mRrj %& gk¡] ;w0lh0Vh0 ckWDl dks vki bZ0Vh0 ckWDl esa vixzsM dj ldrs gS blds fy,

vkidks vixzsM fdV [kjhnuh gksxh ftlesa vkidks ,d LekVZ&dkMZ feysxkA vf/kd

tkudkjh ds fy, vius jh&lsyj dks lEidZ djsaA

iz'u %& ;w0lh0Vh0 lkW¶Vos;j dk u;k oj'ku vkSj ubZ QySl QkbZys dSls izkIr gksxh \mRrj %& b.VjusV }kjk ubZ QkbZyksa ds fy, vki ;w0lh0Vh0 ckWDl ds vkWfQf'k;y

liksVZ ,fj;k ij tk ldrs gSaaA ;gk¡ vki ;w0lh0Vh0 dk ysVsLV oj'ku vkSj ubZ QySl

QkbZys vkjke ls tc pkgs MkmuyksM dj ldrs gSA osclkbZV gS %& www.uct.cc

Page. 25


w w w . u tc . c c


w w w . u tc . c c

Trouble-Shooting

Q. After formatting the phone, the Touch Screen asks for Calibration, but the touchscreen is not working. How to use the phone now?

A. It is always better to take backup of “Touchscreen calibration” settings using the tracker in the MTK module. Connect the phone in tracker mode, go to “Restore Settings” tab, select “TouchScreen calibration data” and then press “Export”. Now same the settings file somewhere safe. You can now flash or format the phone and after that write back the calibration settings file.

Q. UCT is not able to find pinout of the phone and says “Sense failure”

A. If UCT is not able to sense the pinouts of the phone then it is possible that the phone has some other CPU inside other than that selected. Please try with different CPU. But Mostly apprx 90% phones found in Indian market are “MTK” & “SpreadTrum” based.

Q. How to solve Error:“FAILED TO SET MTK_SYNC_CMD, CMD=0XC0”

A. Change baudrate to 115200 and try again.

Q. Can I upgrade UCT Box? How?

A. Yes, You can upgrade the firmware inside the UCT Box. Just download the latest software setup from support area and install it. Inside every installer in available the firmware upgrade utility “UCT Firmware Update”. Just open it, press “ScanPort”, select the com port number of your UCT Box and press “UpGrade-BOX”. your box will be upgraded to latest version and ready to use with latest setup exe.

Trouble-Shooting

Q. Not able to connect MTK handsets with CPU ID 6235.

A. For handsets based on MTK CPU ID 6235 or based on NAND memory, you need to select Flash Type as "NAND". After this connect handset and all should be ok. If still have any problem, you can try with different Boot versions too.

Q. Not able to connect & find pinout for SpreadTurm based handset. “Failed to RXD”

A. As explained, it is very important to select correct Flash type and Boot type for SPD handsets. If you don't know which CPU your handset have, then u can try all one-by-one. After u get Read-Info, you can see exactly which Flash and CPU it has and then select accordingly. Now you can Read Flash, Write Flash, Format, Unlock, etc.

Q. Can we fix 2nd IMEI on SpreadTurm handsets which have Dual Sim features? Means can we fix 2nd IMEI on SPD Handsets?

A. Yes, 2nd IMEI of the handset can also be fixed for SpreadTrum handsets by UCT Box very easily.

1. Read Full Flash Backup of the handset. for eg. old.bin2. Now change the 1st IMEI of this flash file old.bin just as you do for a simple SpreadTrum handset. Save this new file as IMEI_1.bin3. Now again select the file IMEI_1.bin and change the 2nd IMEI of this flash file, you just need to enter the 2nd IMEI of the flash file in the “Original” field this time. Now save this new file as IMEI_2.bin4. You can now flash this file to your handset which will write both new IMEI.

Means, all procedure is same, just that we have to change both the IMEI inside the flash file 1-by-1 and then flash it to the handset.

ç”u % lh0ih0;w0 6235 okys ,e0Vh0ds0 gSaMlsV dusDV D;ksa ugha gksrs \mRrj% lh0ih0;w0 6235 okys gs.MlsV NAND eseksjh ds gksrs gSaA blfy;s ;g

t:jh gS fd vki”kUl esa “NOR” dh txg “NAND” vkSj otZu esa “Ver 3.952” flysDV dj ysaA vc vki lHkh NAND eseksjh okys gs.M lsV dusDV dj ldrs gSaA ;fn vHkh Hkh dusDV uk gks rks vki Version dks ckjh ckjh cnydj dksf”k”k dj ysaA

iz”u% LizsMVªe gs.MlsV dusDV ugh gksrs vkSj u gh fiu vkmV Qkb.M djrs gSaA

mRrj% LizsMVªe lh0ih0;w0 dbZ izdkj ds gksrs gSaA buesa ls vf/kdrj gs.MlsV “Auto USB” vki”ku esa dusDV gks tkrs gSaA vxj ,slk u gks rks vki

“Auto-COM” ;k fQj “6600L-NOR” esa jhM bUQks dksf”k”k dj ldrs gSaA bUQks jhM gksus ds ckn vkidks mudk lgh lh0ih0;w0 irk yx tk;sxk ftls vki vki”ku esa flysDV djds mu gs.MlsV dks ¶ys”k] QksesZV ;k fQj vuyksd dj ldrs gSaA

iz”u% D;k ge ;w0lh0Vh0 ckWDl ls nks vkbZ0,e0bZ0vkbZ0 okys LizsMVªe gs.MlsV dks fjis;j dj ldrs gSa\

mRrj% gka] ;w0lh0Vh0 ckWDl ls LizsMVªe lh0ih0;w0 okys gs.MlsV dk nwljk vkbZ0,e0bZ0vkbZ0 Hkh fjis;j fd;k tk ldrk gSA

1- gs.MlsV dh Qqy ¶ys”k jhM dj ysaA2- vc vki vkbZ0,e0bZ0vkbZ0 vki”ku }kjk ¶ys”k Qkby dk igyk

vkbZ0,e0bZ0vkbZ0 cny ysaA Bhd mlh rjg tSls vki fdlh lkekU; ,d vkbZ0,e0bZ0vkbZ0 okyk gs.MlsV dk djrs gSaA

3- vc bl ubZ Qkby ftldk fd igyk vkbZ0,e0bZ0vkbZ0 cnyk tk pqdk gS mls flysDV djds mldk nwljk vkbZ0,e0bZ0vkbZ0 Hkh cny ysaA bl ckjh vkidks vksfjthuy esa gs.MlsV dk nwljk vksfjthuy vkbZ0,e0bZ0vkbZ0 Mkyuk gksxkA

4- nksuksa vkbZ0,e0bZ0vkbZ0 cnyh gqbZ Qkby dks gs.M lsV esa ¶ys”k dj nsaA lkjk rjhdk lkekU; gh gSA cl bruk QdZ gS fd vkidks ¶ys”k QkbZy ds vUnj ds nksuks vkbZ0,e0bZ0vkbZ0 ckjh&ckjh cnyus gSaAUNIVERSAL CHINA TOOL POWERED BY ET

w w w . u tc . c c

Trouble-Shooting

Q. How can I know which CPU my phone has? Is it a MTK or a SpreadTrum?

A. You can find this out using any of the 3 methods:1. Open the phone and look for the CPU. If its MTK then MT or MTK will be written on the IC, if it's a SpreadTrum then SPD or SpreadTrum will be written on the IC.2. Second way to check is to power on the handset, type *#66#, this will show you the “Engineering mode”. Here you can check about the CPU details.3. Another way to check is by a power supply. Remove battery from handset, give power to handset with external power supply. Now as soon as you give power, if the ampere meter shows some change in reading means it is a SpreadTrum based handset. But if it does not consumes any power, means no activity at the ampere meter, means it's a MTK CPU based handset.

Q. I have disabled my Anti-Virus or added UCT to exclusion, but can you please explain why the Anti-Virus softwares detect UCT files as a threat?

A. If you will notice, important thing is that the Anit-Virus softwares gives a threat to UCT software files as a malware and not a virus. The difference between malware and virus is that a virus is something which is designed to cause harm to the pc, but on the other hand malware is something which is working secretly which the PC or the Anit-Virus software are not able to understand. Now these malware are also blocked by Anti-Virus softwares because these applications are not understood by them.

Now UCT files are such designed that the PC or the Anti-Virus softwares are not able to understand the data inside and thus threatened as malware.

Using UCT Box as Pin-Finder for Infinity or Any other Software

You can use UCT Box as a Pin-Finding hardware for any other software in the market. Means you can find the pinouts of a handset with UCT Box, but flash or format it using some other software you have. This can be done for all the supported CPU types.

1. Connect the handset to the UCT Box as you do usually, Open the UCT Software and read info for it as you do normally.2. Now you can just open the other software you want to use and start doing operations on it.

You can also remove cable from phone, put it back again. Or you can also remove the phone power cable and use battery as you do normally for other gsm handsets. All that is important is that USB power cable from the UCT Box should not be removed.

;w0lh0Vh0 dks vU; lks¶Vos;j ds fy;s fiu QkbUMj ds :i esa iz;ksx djuk

vki ;w0lh0Vh0 ckDl dks fdlh vU; lks¶Vos;j ds fy;s ,d fiu QkbUMj ds :i esa Hkh iz;ksx dj ldrs gSaA bldk eryc gS tSls fd vkids ikl ¶yS”k djus ds dksbZ vkSj lks¶Vos;j gS exj fiuksa dks QkbUM djus ds fy;s vkSj dusDV djus ds fy;s vki ;w0lh0Vh0 dks bLrseky dj ldrs gSaA

1- blds fy;s vki lkekU; rjhds ls gs.MlsV dks ;w0lh0Vh0 ls dusDV djsaA

2- fiuvkmV QkbUM djus ds fy;s jhM bUQks djsaA3- bUQks jhM gksus ds ckn vki viuk vU; lks¶Vos;j [kksysaA vius

lks¶Vos;j esa ;w0lh0Vh0 ckDl dk dke iksVZ flysDV djsa vkSj dusDV djsaA

vki Qksu ls dsfcy dks fudky ds nksckjk yxk Hkh ldrs gSaA exj ;g t:jh gS fd ;w0lh0Vh0 ckDl dh ;w0,l0ch0 dsfcy dks u fudkyk tk;sA ;w0,l0ch0 dsfcy fudkyrs gh fiu vkmV fQj ls fjlsV gks tkrs gSaA


w w w . u tc . c c

Trouble-Shooting

Problem Description:

Initializing...

DA_LIB_VER_3.2.0.7

It is sensing the pinout fast,please hold on the phone Power key

RXD=6 TXD=7

Connecting...Please hold on the POWER key until the red gauge is going...

Failed to read HardCode, REG=0x80000008

Error: Failed to read REG=0x80010008



Reason:

Bad Flash IC or Bad Cable

Solution:

1. Can try to change cable, try with slower baudrate and try few times.

2. Rehot the flash IC and try again. if still not then need replace flash IC.

----------------------------------------------------------------------------


Flashing stops at different percentage everytime. Means first try it stop at 30%, next time

it stop at 35%, then 10% and so and so.

Reason:

This can be due to:

1. Bad Flash Chip

2. Low power to handset

3. Bad data inside Flash Chip

Solution:

First i suggest to try with slow baudrate, try flash with slow baudrate. if this not success

then better erase the complete flash chip and then try again. This should sure help if its

not a hardware fault.

If it still not helps, means can be hardware problem too, in this case you can reflow the

Flash IC or replace if necesarry.

Trouble-Shooting


Not able to work correctly on MTK CPU ID 6217.

Reason:

Unsupported Boot type

Solution:

You need to use supported boot type for this CPU ID. Just select "Boot 3.848" and it

should work ok.

----------------------------------------------------------------------------


"SPD USB TO SERIAL NOT FOUND"

Reason:

The drivers are not installed for SpreadTrum USB communication

Solution:

You need to install the USB drivers for SpreadTrum. when UCT box has finished finding

the pinouts for spreadturm handset, it will ask for SPD drivers, these drivers can be

found inside folder: "C:\UCT\UCT\SpreadTrum_USB_Drivers\" just need to install

them and then UCT can start working your handset.

If in case the computer not asks for any drivers after pinfinding, then you need to un-

install the bad drivers from your device manager and then again re-install the supplied

drivers.

----------------------------------------------------------------------------


"Failed to format Flash"

Reason:

Cannot format the flash for older type handsets, cause they not support new boot type.

Solution:

Just try different boot types and it should be ok. Some boot can work for some handsets.

This is why it is not important that the latest boot will always work for all handsets. it can

be also that only old boot type will work for some particular handsets.

Page. 28


w w w . u tc . c c

Trouble-Shooting


Error "Project ID not found" while connecting the handset

Reason:

UCT Software is not able to find the project id inside the handset flash, project id is the

version of the firmware. This can be cause of wrong boot selection, wrong memory type

selection or can be due to empty flash chip or hardware fault.

Solution:

to solve this, first try with different boot type and mode type, try all boot and also try

with "NAND" memeory type as well. if still not works, then flash the handset with good

flash file. if not able to flash, means bad flash chip, try reflow or replace.

----------------------------------------------------------------------------


Spreadturm handsets show "Failed to RXD"

Reason:

This error can be cause of many problems. can be cause of wrong connectivily, bad cable,

wrong boot type

Solution:

Select "6600L-USB" or "6600L-USB" in options and try again

----------------------------------------------------------------------------


Error: Unsaft EFS Address, Please input the right format address and try again.

Failed to auto format.

Reason:

UCT Software is not able to recognise the flash addresses inside handset

Solution:

Try to do "Reset", If this not helps then only way to fix this is by flashing handset with

correct flash file, if u dont have a flash file then u need to arrange a similar handset, read

the flash from it and then flash it to your faulty handset.

Trouble-Shooting


Read Info, Read Flash working fine for SPD handset, but format anf write flash not

working properly.

Reason:

you are not sellecting the correct option type according to cpu id and flash id.

Solution:

Make readInfo of the handset, here in information you will see the CPU type and the flash

type of the handset, for eg. CPU: 6600xxxxxxxxx Flash: NOR.

Now in this case, you need to select the option "6600L-USB" and then proceed.

Means it is very important to select the correct options, otherwise format, write flash

will not work properly. for details, better read complete guide for SpreadTrum phones.

----------------------------------------------------------------------------


Nor Flash ID: 0000000000000000

Nand Flash ID: 0000000000000000

Nor Flash not found.

Reason:

Bad flash IC

Solution:

You need to replace the flash IC

----------------------------------------------------------------------------


Connecting...Please hold on the POWER key until the red gauge is going...

BB:6227, HardwareVer:8A05, SoftwareVer:8A00

Set RTC Alarm Mask failed, REG=0x405600780

Reason:

Problem is due to low power to handset

Solution:

Keep and press the power button during complete operation. this might help.

Page. 29


w w w . u tc . c c


w w w . u tc . c c

Trouble-Shooting


Reading full Flash...

CRC error: CRC=4C92, CheckSum16=4C8A

Reason:

Bad CRC checksum inside the flash of handset. this is due to bugs inside handset

firmware

Solution:

You need to format the handset first before any other operation.

----------------------------------------------------------------------------


Reading FileSystem info...

Failed to read FS info.

Reason:

The File System is not found by software

Solution:

Only way to solve this is by flashing the handset with correct flash file, or need to read

flash from a working handset and then flash it to faulty handset.

----------------------------------------------------------------------------


Reading FileSystem info...

Error: Get Flash die baseaddress

Reason:

Phone has been tampered with other software or the firmware inside has been

corrupted.

Solution:

You need to look for the Full flash file of this handset and flash to it, If u dont find a flash

file in that case you need to look for a working handset and read flash from it, then flash it

to your dead handset.

Trouble-Shooting


Get error "Invalid IMEI" when trying to repair IMEI for some MTK handsets

Reason:

Some handsets, mostly of CPU 6235 and 6253 have this problem after format. After

format cannot write IMEI and show error Invalid IMEI

Solution:

To solve this you need to flash the handset. There is no other way to solve this problem

for now.

But you can avoid this error by taking NV data backup before formatting the handset.

Just select NV Editor and take full backup of handset before formatting. After format,

write NV data back to handset and then fix IMEI.

----------------------------------------------------------------------------


How to solve error: FAILED TO RUN BOOTLOADER

Reason:

Communication is stopped in middle with handset and UCT Box

Solution:

Press and hold the power button untill all process is completed, if even this not help then

press and hold * key and keep pressed untill all completed.

----------------------------------------------------------------------------


How to solve the error: ERROR: MTK_DA_GET_FAT_INFO_NOT_FOUND

Reason:

UCT Software is not able to read the FAT information from the MTK handset, this is

because of un-compatible flash chip or boot type.

Solution:

Try to select Boot "Ver. 3.952" from the options, if even this not works, then try other

options one-by-one.

Page. 30


w w w . u tc . c c


w w w . u tc . c c

Problem with Anti-Virus Softwares when Installing UCT Box

While installing UCT Software Setup, many Ant-Virus softwares detect the UCT files as virus and deletes them even before installation completes. Due to which you can get error about missing files while installtion. Errors like "UCT v1.00.MSI not found".

To solve this problem, there are 2 solutions. One is to easily just disable your Anti-Virus software and then install the UCT Software. The second method is to add UCT software files to your software "Trusted List" or "Exclusions List".

Step-By-Step Instructions on adding UCT Files to Kaspersky Anti-Virus Exclusions List

1. Open the Anti-Virus main window, click settings, go to "Threats and exclusions".2. Now click "Settings" in front of Exclusions.3. Now you will see the "Trusted zone" window, click "Add", then "Select Object" and add the following files One-By-One to the list:

DownloadAgentLib.dllUCT*.*ET*.*JtagAgent.dllResourceAgent.dll

4. When done, just click "OK" and close the window. Now you can easy install UCT Software and also work with it without any problem.

Page. 31


w w w . u tc . c c


w w w . u tc . c c

UCT Fusion Software

UCT Fusion Software is the latest addition to UCT Box. With Fusion Software you can now do many extra features with your ET-BoX Plus or your latest UCT Box. Like: Define Pinouts, Detect CPU Type, PinFind for MTK 2 CPU handset, Detect the charging pin, Self check the hardware, Upgrade firmware, etc.

To use the UCT Fusion Software, download the latest setup available from the support area and install it step-by-step. After installation you can run it from the “Start - All Programs - UCT Team - UCT Fusion”.

UCT Self Checking

UCT Fusion Software allows to test the UCT and ET-Plus hardware for any technichal problems such as corrupt firmware, bad voltages, low voltages, pinfinder problem or any other small hardware issues.

To Self-Check the UCT hardware:1. Disconnect the 24 pin main cable and the handset from UCT Box.2. Open the latest software for UCT Fusion.3. Press the “Self-check” button in the side bar.4. Now a small window for self checking will pop-up, press “Self-check” and wait for the test to complete.5. After test the software will show you the results for each and every test.

You can now make screenshot of these results and send it to your reseller in case of any problem. This will help in solving the problem with your UCT hardware if u have any.

Page. 32


w w w . u tc . c c

Auto-Detect CPU Type with UCT Fusion

UCT Fusion can automatically detect the CPU type inside the handset. This operation is very useful when you are not sure which CPU does the handset have. Most of the handsets in market are either MTK or SpreadTrum based. These are even distributed in handsets with COM connectivity or USB connectivity, this is why we suggest you to try to connect the handset in “Auto” or “USB” method.

Steps to Auto-Detect CPU Type with UCT Box:1. Connect the handset to UCT Box and open the latest version of Fusion software.2. Press “Scan” in the side bar.3. Select “Auto” and press “Chip Sense”4. Depending on handset, in sometime UCT Fusion will show you the CPU details with the connectivity pinouts.

Note: In case of failure or no response for long time, you can try select “USB” and try again to sense the chip

Find pinouts for CPU 2 in MTK handsets

Some MTK based handsets have 2 CPU’s inside them. Now when we find the pinouts of this type of a handset with a normal procedure, then we are only able to connect to the first CPU. So we can repair only yhe part of the handset which the first CPU is related to.

To fix the second CPU of the same handset, we need to find the pinout of CPU 2 and connect to it. This can now be done with UCT Fusion Software.

Steps to find pinouts of CPU 2 of MTK handset:

1. Connect the handset to the UCT Box and open the latest version of the Fusion software.2. Press “Scan” from the side bar and select “MTK”3. Now press “2nd Definition” and after that keep press the power button on the handset, just like u do for any other MTK based handset.4. In few seconds the UCT Fusion software will detect the pinouts for 2nd CPU and define them.

You can now open the UCT Box Software, select MTK, uncheck “Auto Sense” and proceed with Flash / Format / IMEI Repair, etc. If you will not uncheck “Auto Sense” then UCT Box will again find the 1st CPU pinouts rather than the 2nd CPU.

Page. 33


w w w . u tc . c c

Pinout Defining with UCT Fusion

Q. What is the difference between “Pin-Find” and “Pin-Define” ?A. Pin-Find is to find out the pinouts of the handset. Means which pins are Rx, Tx, Ground, Vcc at the mobile phone connector. Whereas “Pin-Define” means to write the Rx, Tx, Ground and Vcc to the defined pins at cable.

Example:You have a handset, you want to connect it with UCT Box, but you don't know the pinouts of the handset. Then you need to find the pinouts using the “Pin-Find” feature.

On the other side, you have a handset which you want to connect it with UCT Box and you know the pinouts of this handset. Then you need to define the handset pinouts to the UCT Box so that you can start working on it. Here you need to use the “Pin-Define” feature.

Step-By-Step guide on how to use the Pin-Define feature of UCT Fusion:

(In this guide we are using an example to define pinouts of Samsung B319 which uses “Samsung E210 Combo” Cable)

1. Connect the handset with the respective cable (20B) to the UCT Box and start the UCT Fusion software.

2. Press “Definition” in the side bar & select “Standard Mode”.3. Now according to the Samsung E210 pinouts, we need to define the

ground on the pin-1 and pin-2, therefore click on “1” and select “GND” similarly clock on “2” and select “GND”.

4. You can set all other pins similarly. Rxd, Txd, Vcc, USB D-, USB D+, etc.5. After you are all done, press “Set” on the upper right corner. This will

write the command to the UCT Box and pinouts will be defined.

You can now open your ET-Plus Software or any other CDMA software to service your handset.

Page. 34


w w w . u tc . c c


w w w . u tc . c c

UCT Manual Hindi v1.0

Documents

Transcript of UCT Manual Hindi v1.0