UCB & 3C integration Written and Presented by Andy Loffman.
-
Upload
caroline-clements -
Category
Documents
-
view
236 -
download
7
Transcript of UCB & 3C integration Written and Presented by Andy Loffman.
![Page 1: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/1.jpg)
UCB & 3C integrationWritten and Presented by
Andy Loffman
![Page 2: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/2.jpg)
• Add a new soft trunk
Firstly we need to setup the soft trunks on the 3c server for UCB to connect to.
Page 2
![Page 3: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/3.jpg)
• Description – For example NECTrunk.
• Account – Unique name; for example NECtrunk.
• Service Provider Domain – IP address of the UCB server.
• Outbound Proxy – IP address of the UCB server.
• Port – Leave at default 5060.• Registration Type – none.• Primary MGC – Leave
unchanged.• Secondary MGC – Set if you
have one.• Contact Domain – Blank• Preferred Transport – UDP• User Agent – UCB Zeacom SIP
• Once this is completed press the OK buttonPage 3
![Page 4: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/4.jpg)
Right Click on the newly created trunk and view properties.
• Total Capacity – Set the total capacity for incoming and out going calls.
• Inbound Capacity – Total of incoming calls.
• Outbound Capacity – total of outgoing calls.
Page 4
![Page 5: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/5.jpg)
In the settings tab, click add and add the above
• Creating system queues
As a bare minimum we need to create the following queues• Primary queue• Hold queue• Voicemail queue
Page 5
![Page 6: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/6.jpg)
1. Click on the outward routing tab
2. Click to add extension
3. Click New Extension
Page 6
![Page 7: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/7.jpg)
Enter the following details.• Number• First Name
*prefix with Z
We need to setup:ZUCBZvoicemailZhold
*3 separate extensions*
Page 7
![Page 8: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/8.jpg)
When your finished we should have at the very least the below
Now we can add any queues to the 3c system.For the course please add:• Queue1 – 6• Console
Page 8
![Page 9: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/9.jpg)
We need to make the ZUCB queue the primary. Select the queue and click Make Primary
Page 9
![Page 10: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/10.jpg)
Now the queues are created, we need to setup the MOH for the ZeacomSIP agent.
Follow the picture below.
Page 10
![Page 11: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/11.jpg)
UCB 3C Fall over▐ If the UCB server is unavailable for any reason then we need to setup the fall
over on the 3c server.
▐ This is a different way of working if your used to setting up a manual resilience mode on the SV8100. What we are about to setup will automatically move the calls from the UCB server to ring groups or extensions on the 3c server.
Page 11
![Page 12: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/12.jpg)
▐ Go into the 3c number plan tab and add Extension.
Page 12
![Page 13: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/13.jpg)
Add a new extension number, name it and make the Type a Department.
In this example we are setting up the fall over for the console queue
Page 13
![Page 14: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/14.jpg)
Click on the forwarding tab.
Click on the new profile and give a name for example - Failover.Page 14
![Page 15: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/15.jpg)
Press OK to the schedule
Click Add forwarding
• Search for the Zconsole queue
• Apply this condition “immediately”
Page 15
![Page 16: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/16.jpg)
Now we need to setup what happens if the UCB server is unavailable.Click add forwarding again in the Failover profile
Search for the extension or group you want the forward to
Enter the forward time to 15 minutes, this will become immediate should the other forward fail.Once that’s done ok and ok to complete
Page 16
![Page 17: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/17.jpg)
Go into stations and add Softphone
Give the softphone a name
Then click add extension
Page 17
![Page 18: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/18.jpg)
Select the extension we previously setup the forwards on
Click ok and ok to finish the programming
What this failover will achieve is, if the UCB server is not contactable at any time, the 3c server will forward the queue calls immediately to the forward with the 15 minute forward time.
Page 18
![Page 19: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/19.jpg)
We now need to create a user in AD for the UCB server to connect via webservices.
Log on to the AD server and open “Active Directory Users and Computers”
Page 19
![Page 20: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/20.jpg)
Go into users
New
User
Page 20
![Page 21: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/21.jpg)
Enter the first name
Last name
User logon name
Then click next
Page 21
![Page 22: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/22.jpg)
Enter the password
And tick the boxes as per the picture
Then click next
Then Finish
Log off the AD server and go back to the 3C server
Page 22
![Page 23: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/23.jpg)
Log back into 3C administrator
Go into users and click add
Page 23
![Page 24: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/24.jpg)
Expand out “Users”
And click OK on the new account we have just created
Page 24
![Page 25: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/25.jpg)
Tick the boxes as per the screen shot
Tick the Web Services Rights
Enter the password for the AD user
Click Apply
Page 25
![Page 26: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/26.jpg)
Click on the user rights tab
Click add and select zone
Select your sites zone and press OK
Page 26
![Page 27: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/27.jpg)
Change the privilege level from monitor to Full
Page 27
![Page 28: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/28.jpg)
Under the general tab/Zones right click view properties and make sure your UCB webservices acc is set to “Privilege Full”
Page 28
![Page 29: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/29.jpg)
Message waiting.There is 2 setups for message waiting:1st – Using the 3C voicemail and UCB2nd – Just using the UCB voicemail.
We are going to look at the first option of using 3c and UCB voicemail.
Go into stations, select the extension that has UCB VM and set as per the screen shot.
These changes need to be done per extension requiring UCB voicemail.**phone will reboot after the changes are applied**
IP address is the UCB server:5090
Page 29
![Page 30: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/30.jpg)
2nd message waiting option. Just using UCB voicemail.
Doing this compared to the previous slide will stop the message waiting on the 3c voicemail so should only be used if completely using the UCB voicemail.
Go into the general tab, into system initialization settings and set as per the picture.
IP address of the UCB server:5090
Page 30
![Page 31: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/31.jpg)
We now need to install the UCB software on the UCB server
Double click setup
Page 33
![Page 32: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/32.jpg)
Browse to the license file
Page 34
![Page 33: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/33.jpg)
Locate your license file and install it
Page 35
![Page 34: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/34.jpg)
Install third party software
Agree to any licenses etc and press next until install third party software is complete
Page 36
![Page 35: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/35.jpg)
Now run “Configure the SQL Server”
Click here to let the UCB software install SQL Express
If using an existing SQL 2008 then refer to the below document as it will need prep work before you install
Page 37
![Page 36: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/36.jpg)
Install Aculab drivers. You will get prompted several times to install, keep clicking install until its finished
Page 38
![Page 37: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/37.jpg)
Now the aculab is completed click – Install on Launch CTI Installer
Accept any license agreements and input area code on location information if requested
When finished click run to restart the cti server
Page 39
![Page 38: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/38.jpg)
After the server has rebooted, administrator will start automatically and run installation wizards
Click on Configure Default Company
Enter a site name and click ok to finish
Page 40
![Page 39: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/39.jpg)
Click on Define phone system type
Select NEC Univerge 3C and click ok
Page 41
![Page 40: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/40.jpg)
Click in Configure PBX Connection
Page 42
![Page 41: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/41.jpg)
Enter the name of the 3C server*click test to confirm connectivity*
Enter webservices username in formatDomain\useracc
Enter web services password
Queue identifier – input Z
Click next then finish to complete the pbx setup
Page 43
![Page 42: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/42.jpg)
Click PBX Essentials
Enter the hold number we created on 3c, from our previous slides 4565
Enter the voicemail number - 4555
Enter the primary address ZUCB 4567
Enter a Voice messaging ddi number if required
Click next then finish to complete the PBX essentials
Page 44
![Page 43: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/43.jpg)
Next click configure operator console
As previously setup Zconsole on ucb enter 4568
Click close on the installation process, when you click close it will prompt you to open application manager to install the appropriate modules, click ok at this point.
Application manager will start up and this screen will appear, click add the pbx module
Page 45
![Page 44: UCB & 3C integration Written and Presented by Andy Loffman.](https://reader035.fdocuments.us/reader035/viewer/2022062303/551afb1a55034606048b65b2/html5/thumbnails/44.jpg)
Then click add announce ports
Click close after that for the application checks
Page 46
You should then the sip ports added
Then go into alerts in the application manager and we are looking for “ports learnt Successfully”