U70

TECHNICALGLASS REGULATIONS

GLASS REGULATIONS

MAXIMUM SIZES

Clear glass (Annealed, Toughened or Laminated) is available in sizes up to a maximum width or height of 2500mm, however there is limitations on the type depending on the situation. Patterned glass is available up to 1320mm x 2140mm high with the pattern running across the width.

GLASS WEIGHTS 20kg/m2 – 4/20/4 (28mm) 30kg/m2 – 6/16/6 (28mm)

SAFETY GLASSAll glazing within buildings conforms to BS 6262 and is divided into two main areas:

ANNEALED

SAFETY – Toughened –

is other work must be carried out prior; if this type of glass is broken it disintegrates into small reasonably safe pieces.

SAFETY – Laminated – is produced by combining two or more panes of glass with layers of polyvinylbutyral (p.v.b) or resin interlayers. With a different amount of combinations of the type of interlayer & glass the end result will produce a range of features such

SAFETY AREASThe diagram below indicates various locations where it is deemed `critical` in terms of safety. These are

play etc.

Note:- The above table is extracted from BS6262 and is based on a Design Wind Pressure of 1200 Pa

GLAZING OPTIONS

THICKNESS ANNEALED LAMINATED TOUGHENED

2m2 N/A 3m24mm

5m2 4.5m2 7m26mm

4m2 N/A 6m24+4

10m2 9m2 7m26+6

GLASS SPECIFICATIONS

SATISFYING THE REQUIREMENTS

Glazing In Doors:

Minimum Class C to BS 6206 and be marked accordingly. If the smaller dimension of the pane is greater than 900mm it shall be: Minimum Class B to BS 6206 and be marked accordingly.

Low Level Glazing:

Minimum Class C to BS 6206 and be marked accordingly.

Glazing Adjacent to Door Glazing Which is wholly or partially within 300mm of the edge of a door and which is wholly or partially within 1500mm

Minimum Class C to BS 6206 and be marked accordingly. If the smaller dimension of the pane is greater than 900mm it shall be: Minimum Class B to BS 6206 and be marked accordingly.

FIRE ESCAPE RULING

Any window provided for emergency egress purposes and any external door provided for escape should comply with the following conditions.

1) The window should have an unobstructed openable area that is at least 0.33m2 and at least 450mm wide and750mm high (the route through the window may be at an angle rather than straight through). The bottom of the

This is a matter of judgement in each case, but in general a courtyard or back garden from which there is no exit other than through other buildings would have to be at least as deep as the dwelling is high to be acceptable.

GLASS REGULATIONS

Use this leaflet to check if your window and doorinstallation complies with the requirements forsafety glazing

Why Check ?• You need to be sure that your home is a Safe Environment.• It is a legal requirement to install safety glazing in Critical Locations. Checking could save lives.• Approved Document N (Glazing - Protection against impact) of the Building Regulations in England

and Wales provides guidance for safety glazing.

• BS 6262-4:2005 provides details of safety glazing requirements.What you need to do• Identify areas in your home that are considered to be ‘critical locations’ (see Figure 1 - over page).• You must then check that these critical locations have safety glazing material installed.• If safety glazing material has been installed, there will be visible markings you can check.

All safety glasses must be visibly marked on the glass. If the ‘visible markings’ on the safety glazingmaterial is not clear or you have any concerns about whether the safety glazing has been installed tothe correct standard, you should go back to the original window installer and seek advice.If you are not happy with their response, you should contact FENSA www.fensa.org.uk

Safety Glazing is:• A glass or glazing product which conforms to the relevant European glazing standard

e.g. BS EN 12150 or BS EN 14449 or BS EN 14179.

• The glass has also been tested against the European standard for BS EN 12600 for safety impact.This means that on impact the glass does not break or breaks in a way unlikely to cause serious injury.

Safety Glazing needs to be installed in Critical Locations

Check here that your windows comply with Building Regulations

Essential Window and Door SafetyInformation For Homeowners

If you have recently installed windows or doors you areSTRONGLY URGED to read this leaflet

Identifying ‘Critical Locations’ in your home

There are instances where glazing other than safety glass and safety plastics are deemed to besatisfactory but these are EXCEPTIONS.

New System• The glass product standard which the glass complies with e.g.

BS EN 12150, BS EN 14179, BS EN 14449

• The classification following testing to BS EN 12600.This will be Class 1,2 or 3.

• The name or trade mark of the manufacturer.Old System (obsolete)

• The British Standard number BS 6206.• The category of safety glass being used e.g. Class A, Class B or Class C.• The name, trade mark or other identification mark of the

manufacturer, merchant or installer.

How to check for visible markings on safety glass

Safety Glazing needs to be installedin Critical Locations

Figure 1:CriticalLocations

‘The diagram hasbeen used withkind permissionof BSI’

The marking requirements have recently changed.The visible markings on each piece ofsafety glazing within ‘critical locations’ (see below) must be clearly and indelibly marked with:

The shaded areas (Figure 1) are critical locations whichrequire the use of safety glass.These are:

Those areas of internal and external walls that areconsidered ‘critical locations’ in terms of safety are:a) Between the finished floor level and 1500mm above

that level in doors and in side panels which are within300mm of either edge of the door.

b) Between the finished floor level and 800mm above thatlevel in the case of windows not included in a) above.

c) Glazing in Bathing Areas:Any glazing forming part of a bath orshower screen, or located adjacent to, orsurrounding, a bath, swimming pool, orother associated wet area, constitutes apotential danger because of the possibilityof a person slipping on a wet surface, Inthese cases, all glazing should be SafetyGlazing conforming to BS 6262-4:2005.A window within 800mm of the bottom ofa bath or shower should be safety glass.

ACME GLASS COBS EN 12150

1

Example of a Visible Marking:

V2 June 08

Essential Window and Door Safety Information For Homeowners

Safety Glazing needs to be installed in Critical Locations Check here that your windows comply with Building Regulations

Use these details to check if your window and door installation complies with the requirements for safety glazing

Safety Glazing needs to be installed in Critical LocationsCheck here that your windows comply with Building Regulations

Safety Glazing needs to be installed in Critical Locations

There are instances where glazing other than safety glass and safety plastics are deemed to be satisfactory but these are EXCEPTIONS.

GLASS REGULATIONS

Use this leaflet to check if your window and doorinstallation complies with the requirements forsafety glazing

Why Check ?• You need to be sure that your home is a Safe Environment.• It is a legal requirement to install safety glazing in Critical Locations. Checking could save lives.• Approved Document N (Glazing - Protection against impact) of the Building Regulations in England

and Wales provides guidance for safety glazing.

• BS 6262-4:2005 provides details of safety glazing requirements.What you need to do• Identify areas in your home that are considered to be ‘critical locations’ (see Figure 1 - over page).• You must then check that these critical locations have safety glazing material installed.• If safety glazing material has been installed, there will be visible markings you can check.

All safety glasses must be visibly marked on the glass. If the ‘visible markings’ on the safety glazingmaterial is not clear or you have any concerns about whether the safety glazing has been installed tothe correct standard, you should go back to the original window installer and seek advice.If you are not happy with their response, you should contact FENSA www.fensa.org.uk

Safety Glazing is:• A glass or glazing product which conforms to the relevant European glazing standard

e.g. BS EN 12150 or BS EN 14449 or BS EN 14179.

• The glass has also been tested against the European standard for BS EN 12600 for safety impact.This means that on impact the glass does not break or breaks in a way unlikely to cause serious injury.

Safety Glazing needs to be installed in Critical Locations

Check here that your windows comply with Building Regulations

Essential Window and Door SafetyInformation For Homeowners

If you have recently installed windows or doors you areSTRONGLY URGED to read this leaflet

Identifying ‘Critical Locations’ in your home

There are instances where glazing other than safety glass and safety plastics are deemed to besatisfactory but these are EXCEPTIONS.

New System• The glass product standard which the glass complies with e.g.

BS EN 12150, BS EN 14179, BS EN 14449

• The classification following testing to BS EN 12600.This will be Class 1,2 or 3.

• The name or trade mark of the manufacturer.Old System (obsolete)

• The British Standard number BS 6206.• The category of safety glass being used e.g. Class A, Class B or Class C.• The name, trade mark or other identification mark of the

manufacturer, merchant or installer.

How to check for visible markings on safety glass

Safety Glazing needs to be installedin Critical Locations

Figure 1:CriticalLocations

‘The diagram hasbeen used withkind permissionof BSI’

The marking requirements have recently changed.The visible markings on each piece ofsafety glazing within ‘critical locations’ (see below) must be clearly and indelibly marked with:

The shaded areas (Figure 1) are critical locations whichrequire the use of safety glass.These are:

Those areas of internal and external walls that areconsidered ‘critical locations’ in terms of safety are:a) Between the finished floor level and 1500mm above

that level in doors and in side panels which are within300mm of either edge of the door.

b) Between the finished floor level and 800mm above thatlevel in the case of windows not included in a) above.

c) Glazing in Bathing Areas:Any glazing forming part of a bath orshower screen, or located adjacent to, orsurrounding, a bath, swimming pool, orother associated wet area, constitutes apotential danger because of the possibilityof a person slipping on a wet surface, Inthese cases, all glazing should be SafetyGlazing conforming to BS 6262-4:2005.A window within 800mm of the bottom ofa bath or shower should be safety glass.

ACME GLASS COBS EN 12150

1

Example of a Visible Marking:

V2 June 08

Essential Window and Door Safety Information For Homeowners

Safety Glazing needs to be installed in Critical Locations Check here that your windows comply with Building Regulations

Use these details to check if your window and door installation complies with the requirements for safety glazing

Safety Glazing needs to be installed in Critical LocationsCheck here that your windows comply with Building Regulations

Safety Glazing needs to be installed in Critical Locations

There are instances where glazing other than safety glass and safety plastics are deemed to be satisfactory but these are EXCEPTIONS.