Typhoon 16B (Nobles Wet/Dry Vacuum) · PDF fileOPERATION Typhoon 16B (07–99) 3 SAFETY...

Wet/Dry Battery Vacuum

Typhoon �16B

Model No.: 608817608818 - PAC

Operator and Parts Manual

608819Rev. 00 (09-99)

CUSTOMER SERVICE: 1-800-365-6625FAX: 1–800–678–4240

NOBLES12875 RANSOM STREET HOLLAND MI 49424 U.S.A.

OPERATION

2 Typhoon� 16B (07–99)

This manual is furnished with each new machine. Itprovides necessary operation and maintenanceinstructions and an illustrated parts list.

Read this manual completely and understand themachine before operating or servicing it.

When ordering replacement parts, use the Parts Listsin this manual. Before ordering parts or supplies, besure to have your machine model number and serialnumber handy. Parts and supplies may be ordered byphone or mail from any Authorized Service Center orDistributor.

This machine will provide excellent service. However,the best results will be obtained at minimum costs if:

� The machine is operated with reasonable care.

� The machine is maintained regularly - per themaintenance instructions provided.

� The machine is maintained with manufacturer’ssupplied or equivalent parts.

MACHINE DATA

Model No.-

Install. Date -

Serial No.-

Please fill out at time of installation for future reference.

�1999 Tennant Company Printed in the U.S.A.

Nobles is a registered United States trademark of Tennant Company.

Typhoon is a United States trademark of Tennant Company.

TABLE OF CONTENTS

SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . .

MACHINE COMPONENTS 4. . . . . . . . . . . . . . .

OPTIONAL ACCESSORY KITS 4. . . . . . . . . .

MACHINE INSTALLATION 5. . . . . . . . . . . . . . . MACHINE UNCRATING 5. . . . . . . . . . . . . . . . . BATTERY INSTALLATION 5. . . . . . . . . . . . . . . SQUEEGEE KIT INSTALLATION 5. . . . . . . . .

MACHINE SETUP 7. . . . . . . . . . . . . . . . . . . . . . . . WET VACUUMING 7. . . . . . . . . . . . . . . . . . . . . DRY VACUUMING 7. . . . . . . . . . . . . . . . . . . . . .

MACHINE OPERATION 7. . . . . . . . . . . . . . . . . . VACUUM MOTOR THERMAL PROTECTOR 7. . . . . . . . . . . . . . . . . . . . . . . . . ACCESSORY TOOL OPERATION 7. . . . . . . . SQUEEGEE OPERATION (OPTION) 8. . . . . .

DRAINING RECOVERY TANK 8. . . . . . . . . . . .

BATTERY CHARGING 9. . . . . . . . . . . . . . . . . . . WHEN TO RECHARGE BATTERIES 10. . . . .

MAINTENANCE 10. . . . . . . . . . . . . . . . . . . . . . . . . DAILY MAINTENANCE 10. . . . . . . . . . . . . . . . . WEEKLY MAINTENANCE 10. . . . . . . . . . . . . . MONTHLY MAINTENANCE 10. . . . . . . . . . . . . EVERY 250 HOURS OF OPERATION 10. . . . BATTERY MAINTENANCE 11. . . . . . . . . . . . .

STORING MACHINE 11. . . . . . . . . . . . . . . . . . . .

TROUBLE SHOOTING 12. . . . . . . . . . . . . . . . . .

SPECIFICATIONS 12. . . . . . . . . . . . . . . . . . . . . . .

WIRING DIAGRAM 13. . . . . . . . . . . . . . . . . . . . . .

PARTS LISTUPPER HOUSING PARTS 14. . . . . . . . . . . . . LOWER HOUSING PARTS 16. . . . . . . . . . . . .

OPTIONS 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SQUEEGEE KIT BREAKDOWN 18. . . . . . . . .

OPERATION

Typhoon� 16B (07–99) 3

SAFETY PRECAUTIONS

This machine is intended for commercial use. It issuited to pick up water or dry debris in an indoorenvironment and is not constructed for any other use.

All operators must read, understand and practice thefollowing safety precautions:

The following safety alert symbols are used throughoutthis manual as indicated in their description.

WARNING: To warn of hazards or unsafepractices which could result in severe personalinjury or death.

FOR SAFETY: To identify actions which must befollowed for safe operation of equipment.

The following information signals potentially dangerousconditions to the operator or equipment:

FOR SAFETY:

1. Do not operate machine:– Unless trained and authorized.– Unless operator manual is read and

understood.– In flammable or explosive areas unless

designed for use in those areas.– If not in proper operating condition.– Without bag and/or filters in place.

2. Before operating machine:– Make sure all safety devices are in place

and operate properly.

3. When using machine:– Do not pick up burning or smoking debris,

such as cigarettes, matches or hot ashes.– Report machine damage or faulty

operation immediately.

4. Before leaving or servicing machine:– Stop on level surface.– Turn off machine.

5. When servicing machine:– Disconnect battery connections before

working on machine.– Wear protective gloves when handling

batteries or battery cables.– Avoid contact with battery acid.– Use manufacturer supplied or approved

replacement parts.

WARNING: Batteries emit hydrogen gas.Explosion or fire can result. Keep sparks andopen flame away. Keep battery compartment openwhen charging.

WARNING: Flammable materials or reactivemetals can cause explosion or fire. Do not pickup.

OPERATION

4 Typhoon� 16B (07–99)

MACHINE COMPONENTS

31

5

2

7

4

6

98

1. Bag Compartment Cover2. Vacuum Hose Snout3. Control Grips4. Squeegee Kit Vacuum Hose (optional)5. Vacuum Bag Compartment/

Recovery Tank6. Battery Compartment

3

11

12

10

13

7. Compartment Latches8. Swivel Casters/300 mm (12 in) Rear Wheels9. Squeegee Kit (optional)10. Machine ON/OFF Switch11. Drain Hose12. Squeegee Kit Lift Pedal (optional)13. Charger Plug

OPTIONAL ACCESSORY KITS

To order kit, contact your local distributor and specifypart number:

1 2

2

1. Squeegee Kits – 660 mm (26 in) #190108,840 mm (33 in) #190972, 990 mm (39 in) #190958

2. 6–Piece Accessory Tool Kit #165933. 3–Piece Accessory Tool Kit #190142

3

OPERATION

Typhoon� 16B (11–99) 5

MACHINE INSTALLATION

MACHINE UNCRATING

Carefully check carton for signs of damage. Reportdamage at once to carrier. Check contents list belowto ensure all standard accessories are included.

Carton Contents:

1 – Battery Hardware Package1 – 3m (10 ft) Vacuum Hose1 – Package of Paper Bags1 – Cloth Bag

Accessory Tools and Squeegee Kits are optional, theymust be ordered separately. To order kits see page 4.

BATTERY INSTALLATION

NOTE: Attach Squeegee Assembly kit prior toinstalling batteries. See Squeegee Kit Installation.

Recommended Battery Specifications:

Two 12 volt 105/130 amp hour deep cycle batteries.Maximum battery dimensions are180mm (7in)W x 340mm (13.5in) L x 250mm (10in) H.

BATTERY COMPARTMENT SIZE: 340mm(13.5in) L x 360mm(14in) W x 250mm(10in) D

Recommended Battery Charger:

120/230V–15 amp fully automatic battery charger.


FOR SAFETY: When servicing machine, wearprotective gloves when handling batteries orbattery cables. Avoid contact with battery acid.

1. Turn ON/OFF switch to off.

ATTENTION: Make sure tanks are empty beforeopening.

2. Open battery compartment, unlatch lower latchesand carefully tilt upper housing backwards to floor.Remove loose battery cables at bottom ofcompartment (Figure 1.).

FIG. 1.

3. Carefully install batteries into compartment andarrange battery posts and connect battery cablesto batteries as shown. Red to positive (+) andblack to negative (–) (Figure 2.).

(–) (+)

(–)(+)

FIG. 2.

ATTENTION: Do not drop batteries intocompartment! Battery and machine housingdamage may result. This damage is not coveredby warranty.

4. Double check all connections before closingbattery compartment.

5. To ensure a full charge for first time use, batteriesmay need charging before operating. SeeBATTERY CHARGING on page 9.

SQUEEGEE KIT INSTALLATION

NOTE: Kit installation is made easy if batteries are notinstalled. However, kit can be installed with batteries inplace.

1. Remove vacuum bags and/or empty recoverytank.

2. Tip machine on backside. Only if batteries areremoved from machine.

3. Remove two unused squeegee mounting screwsfrom bottom of machine.

OPERATION

6 Typhoon� 16B (07–99)

4. Install squeegee mounting bracket as shown.Secure with screw and washers that you removed(Figure 3.).

FIG. 3.

5. Fasten squeegee bracket to mounting bracket.Use two (2) clevis and cotter pins provided. Standmachine upright (Figure 4.).

FIG. 4.

6. Insert spacer through hole in pedal then positionpedal between two holes in squeegee bracket.Secure with hardware provided (Figure 5.).

FIG. 5.

7. Position pedal between two L–brackets at rear ofmachine and secure with clevis and cotter pins(Figure 6.).

FIG. 6.

8. Attach squeegee assembly to bracket as shownand secure with two thumb screws (Figure 7.).

FIG. 7.

9. Connect 1090 mm (43 in) vacuum hose tosqueegee assembly and to cover snout (Figure 8.).

FIG. 8.

OPERATION

Typhoon� 16B (07–99) 7

MACHINE SETUP

To ensure a full battery charge before operating,batteries may need charging (See BATTERYCHARGING).

WET VACUUMING


1. Open machine cover and remove vacuum bagfrom recovery tank (Figure 9.).

FIG. 9.

2. Make sure automatic float shut-off screen is inplace (Figure 10.).

FIG. 10.

ATTENTION: To prevent vacuum motor damage,automatic float shut-off screen must be in place.

DRY VACUUMING

1. Open vacuum machine cover and install cloth filterbag, make sure that the bag edge is properlyseated on compartment rim (Figure 11.).

For easy debris disposal and to increase the life ofcloth filter bag, use a paper vacuum bag with thecloth bag. Place the paper bag inside of cloth bagand tuck the top of paper bag around outside rimof cloth bag. Never use paper bag without clothfilter bag in place. Do not reuse paper bags –always dispose.

FIG. 11.

ATTENTION: Always make sure that a bag is inplace before dry vacuuming. Operating machinewithout bag in place will damage vacuum motor.This damage is NOT covered by warranty.

2. Close cover and fasten latches.

3. Leave automatic float shut–off screen in placewhen dry vacuuming. It can provide limitedvacuum motor protection for a faulty bag.

MACHINE OPERATION

FOR SAFETY: Do not operate machine unlessoperator manual is read and understood.


VACUUM MOTOR THERMAL PROTECTOR

Vacuum motor is thermally protected by a temperaturesensor device. It will trip if motor has an overload. Ifmotor should quit, wait 20 minutes for motor to cooland remove obstruction before continuing.

ACCESSORY TOOL OPERATION

1. Connect 3m (10 ft) vacuum hose to machine coversnout.

OPERATION

8 Typhoon� 16B (07–99)

2. Select desired accessory tool and connect tovacuum hose (Figure 12.).

FIG. 12.

3. Activate ON/OFF switch and operate accessorytool as normal.

4. During DRY vacuuming, check bag periodically forfullness. For best suction performance, empty bagat 3/4 full.

During WET vacuuming, the float shut-off screenwill automatically stop water intake when recoverytank becomes full (See DRAINING RECOVERYTANK).

ATTENTION: If foam develops in recovery tankduring wet vacuuming, use a quality defoamerchemical to eliminate the foam. Foam buildup willNOT activate float, and will cause damage to thevacuum motor. Damage due to foam is NOTcovered by warranty.

SQUEEGEE OPERATION (OPTION)

1. Lower squeegee to floor, lightly kick the pedalforward to release from transport position(Figure13.).

FIG. 13.

2. Activate the ON/OFF switch.

3. Begin operating by pushing and pulling machine ineither direction.

4. During operation, the float shut-off screen willautomatically stop water intake when recoverytank becomes full (See DRAINING RECOVERYTANK).

ATTENTION: If foam develops in recovery tankduring wet vacuuming, use a quality defoamerchemical to eliminate the foam. Foam buildup willNOT activate float, and will cause damage to thevacuum motor. Damage due to foam is NOTcovered by warranty.

5. To raise squeegee, step downward on pedal untilpedal engages in the transport position(Figure 14.).

FIG. 14.

NOTE: Squeegee Kit can be used to pick up fineparticles (dust, sand, sawdust, etc...). Squeegee notrecommended for ordinary dry pick up.

DRAINING RECOVERY TANK

1. Push machine to nearest floor drain, if notavailable use a bucket to drain machine.

2. Remove drain hose from holder and twist off drainhose knob and drain. Raise hose to stop flow ofwater (Figure 15.).

FIG. 15.

3. After draining recovery tank, open cover andthoroughly rinse out tank with clean water.

4. Replace drain hose knob securely and return toholder.

NOTE: Be certain drain hose knob is secure toprevent suction loss.

OPERATION

Typhoon� 16B (11–99) 9

BATTERY CHARGING

The following charging instructions are intended formanufacturer supplied 24V chargers. Use thefollowing recommended charger specifications toprevent battery damage.

CHARGER SPECIFICATIONS:

� OUTPUT VOLTAGE - 24 VOLTS

� OUTPUT CURRENT - 15 AMPS

� AUTOMATIC SHUTOFF CIRCUIT

� FOR DEEP CYCLE BATTERY CHARGING

NOTE: For optimum machine operation, keepbatteries charged at all times. Do not let batteries setin a discharge condition.

ATTENTION: Do not continue to run machinewhen pick–up performance begins to decrease,battery damage may result.


FOR SAFETY: When servicing machine, wearprotective gloves and shield eyes when handlingbatteries or battery cables. Avoid contact withbattery acid.

1. Turn On/Off switch to off.

2. Push machine to a well ventilated area forcharging.

ATTENTION: Make sure tanks are empty beforeopening.

3. Open battery compartment, unlatch lower latchesat front of machine and carefully tilt upper housingbackwards to floor (Figure 16.).

FIG. 16.

4. Check electrolyte level ‘‘A” in each battery cell. Donot charge batteries unless level is slightlycovering battery plates ‘‘B”. If needed, add justenough distilled water to slightly cover plates. DONOT overfill. Batteries can overflow duringcharging due to expansion. Replace cell capsbefore charging (Figure 17.).

A

B

FIG. 17.

5. With the charger DC outlet plug disconnected frombatteries, plug charger power supply cord into agrounded wall outlet (Figure 18.).

Grounded

Grounding

Edge/hole

Grounded

3 Hole Outlet

Ground Pin

(120V) (230V)

Outlet

FIG. 18.

6. Connect charger to charger receptacle located atrear of machine. The charger automaticallybegins charging and will shut off at a full charge(Figure 19.).

FIG. 19.

7. Charger will automatically begin charging batteriesand shut off when fully charged.

8. After charger has turned off, disconnect chargerfrom batteries before unplugging charger from walloutlet.

9. Recheck battery electrolyte level after charging. Ifneeded, add distilled water to bring level to bottomof sight tubes. Be certain to replace cell capssecurely and to wipe off the top of batteries with aclean cloth.

OPERATION

10 Typhoon� 16B (07–99)

WHEN TO RECHARGE BATTERIES

To prolong the life of your batteries:

� Recharge batteries after every 4 hours of run time.

� Do not charge batteries after every short time use.Wait until a total of 4 hours of run time.

� Do not continue to run machine when pick–upperformance begins to decrease.

� Check electrolyte level before charging.

� Never let batteries sit discharged for more than afew days.

� Always follow proper charging instructions.

MAINTENANCE

To keep machine in good working condition, simplyfollow machines daily, weekly and monthlymaintenance procedures.

FOR SAFETY: When servicing machine,disconnect batteries before working on machine.

DAILY MAINTENANCE

1. Drain and rinse out recovery tank after wetvacuuming.

2. Clean squeegee blades with a cloth. Replaceblades when they become worn.

3. Check bag for fullness, empty bag at 3/4 full.

4. Clean machine housing with a non–abrasive,non-solvent cleaner.

5. Recharge batteries if needed.


WEEKLY MAINTENANCE

1. Remove and clean the float shut–off screen fromrecovery tank (Figure 20.).

FIG. 20.

ATTENTION: Always have float shut–off screen inplace before operating. During wet operation, thefloat shut–off screen protects the vacuum motorfrom water. During dry vacuuming, the floatshut–off screen can provide limited protection fora faulty filter bag.

2. Check electrolyte level in battery cells (See BATTERY MAINTENANCE).

3. Clean battery tops of corrosion.

4. Check for loose or corroded battery cables.

MONTHLY MAINTENANCE

1. To maintain maximum performance, wash clothfilter bag by hand with a mild detergent. Let bagdry thoroughly before replacing.

2. Lubricate axle grease fittings with a water resistantgrease.

3. Lubricate front swivel casters with a silicone spray.

4. Check machine for loose nuts and bolts.

EVERY 250 HOURS OF OPERATION

Check motor for carbon brush wear, replace brushes ifworn to 10 mm (0.38 in) or less.

OPERATION

Typhoon� 16B (07–99) 11

BATTERY MAINTENANCE


FOR SAFETY: When servicing machine, wearprotective gloves and shield eyes when handlingbatteries or battery cables. Avoid contact withbattery acid.

1. Always follow proper charging instructions (SeeBATTERY CHARGING ).

2. Each week AFTER charging, check electrolytelevel in each battery cell of all batteries. Level (A)should reach bottom of sight tubes (B). If needed,add just enough distilled water to reach bottom ofsight tubes. DO NOT overfill (Figure 21.).

A

B

FIG. 21.

3. Keep battery tops and terminals clean and dry.Follow instructions below:a. Mix a strong solution of baking soda and

water.b. Brush solution sparingly over battery tops,

terminal and cable connectors.

NOTE: Do not allow baking soda solution to enterbattery cells.c. Use wire brush to clean terminal post and

cable connections.d. After cleaning, apply a coating of clear battery

post protectant to terminals and cableconnections.

4. Check for loose or worn battery cables. Replace ifworn.

5. Replace batteries if any physical damage isnoticed.

STORING MACHINE

Before storing the machine perform the followinginstructions below:

1. Empty and rinse out recovery tank and accessorytools.

2. Empty or replace vacuum bag.

3. Raise or remove squeegee assembly.

4. Store machine in a dry area in the upright position.

5. Disconnect battery cables if storing for a lengthyperiod.

ATTENTION: Do not store outdoors and avoidgetting wet. Do not allow machine to freeze.

ATTENTION: If storing machine in freezingtemperatures, be certain to drain machine of allwater. Damage due to freezing is not covered bywarranty.

OPERATION

12 Typhoon� 16B (07–99)

TROUBLE SHOOTING

PROBLEM CAUSE SOLUTIONNo power. Faulty ON/OFF switch Contact Service Center.

Batteries need charging. See BATTERY CHARGING.Faulty battery(s). Replace battery(s).Loose battery cable. Tighten loose cables.Batteries are not connectedcorrectly.

See BATTERY INSTALLATION.

Vacuum motor thermal overloadtripped.

Check air flow for obstruction, wait 20 minutesfor motor to cool.

Faulty vacuum motor wiring. Contact Service Center.Poor pick–up. Air flow obstruction. Remove obstruction from ball float screen,

vacuum hose, accessary tool or squeegee.Vacuum bag is full. Empty or replace bag.Ball float screen is activated. Drain recovery tank.Drain hose plug is loose or off. Secure drain hose plug.Cover latches are not engaged. Engage cover latches.Batteries need charging. Charge batteries.Worn cover gasket. Replace gasket.Vacuum motor carbon brushes worn. Contact Service Center.

Short run time. Batteries not fully charged. Charge batteries.Faulty battery(s). Replace battery.Batteries need maintenance. See BATTERY MAINTENANCE.Faulty charger. Replace charger.

SPECIFICATIONS

Model TYPHOON� 16BLENGTH 840 mm ( 33 in)

WIDTH 530 mm ( 21 in)

HEIGHT 1090 mm ( 43 in)

WEIGHT – WEIGHT WITH BATTERIES 41 Kg (90 lbs) – 107Kg (235 lbs)

VACUUM MOTOR 24V, 3–stage, .75hp, 23A, 566W

SEALED WATER LIFT 1780 mm (70 in)

BATTERIES 2–12V deep cycle lead acid, 105AH or 130AH

RUN TIME on full charge 4 hours

DECIBEL RATING AT OPERATOR’S EAR, INDOORS ON TILE >70dB(A)

WIRING DIAGRAM

Typhoon� Battery (09–97) 13

SWITCH

VACUUMMOTOR

CHARGERPLUG

12 VOLTBATTERY

12 VOLTBATTERY

HANDLE

RE

D

WH

T

BLK

BLK

WH

T

WH

T

BLK

BLK

BLACK JUMPER

PARTS LIST

Typhoon� 16B (04–98)14

UPPER HOUSING PARTS

13

12

3

4

5

6

7

8

11 10 910

9

10

1310

1412

626160

59

58

53

545556

5150

49

48

47

46

57

45

44

4210

9

43

2221

41 40

39

37

10

9

38

10

13

36

35

30

34

31

30

32

27

28

26

29

1064

33

15

17

18

19

2021

22

23

25

24

11

63

6566

16

52

67

tennant

#600654 - LABEL, DASH

tennant

PARTS LIST

Typhoon� 16B (07–99) 15

UPPER HOUSING PARTS LIST

REF PART # DESCRIPTION QTY.

1 140801 SCREW, 8–32X3/8 4

2 140023 WASHER, LOCK 4

3 140932 LATCH, RUBBER 2

4 608613 COVER, GREEN 1

5 230497 BRACKET 1


7 140197 SCREW, 10–24X3/8 2

8 100097 GASKET 1

9 140885 SCREW, 1/4–20X1/2 20

10 578244000 WASHER, LOCK 25

11 140000 WASHER, FLAT 10

12 230318 HINGE 1

13 140824 SCREW, 1/4–20X5/8 6

14 140003 WASHER, FENDER 2

15 608461 HOUSING, HANDLE, GREEN 1

16 19417 SWITCH 1

17 200823 GRIP, HANDLE BK 2

18 230696.BK BRACKET, DRAIN HOSE 1

19 140825 SCREW, #6X1/2 2

20 140231 SCREW, 3/8–16X1 1/2 2



23 130110 BUSHING, STRAIN RELIEF 2

24 130384 ASM. WIRE 14/2X26” 1

25 130385 ASM. WIRE 14/2X45” 1

26 180613 FLOAT, AUTO SHUT–OFF 1

27 100381 ELBOW, VAC TUBE 1

28 100096 GASKET 1

29 700435 ASM. PVC ELBOW 1

30 140308 CLAMP 2

31 160482 HOSE, VACUUM 1

32 140199 SCREW, 1/4–20X4 1/2 4

33 100380 MOUNT, VAC MOTOR 1

34 100038 GASKET 1

35 130397 MOTOR, VAC 24VDC 1

190163 BRUSH, CARBON (2/PK) 2


36 100143 GASKET 1

37 230522 BRACKET, VAC MOUNT 1

38 140340 SCREW, #10X5/8 4

39 230980.BK PLATE, COVER MOTOR 1

40 100831 GASKET 1

41 140201 SCREW, 3/8–16X3/4 2

42 230951 HINGE 1

43 160481 HOSE, VACUUM, 3M 1

44 140307 CLAMP 1

∇ 701170 ASM., DRAIN HOSE 1

�45 160418 HOSE, DRAIN 1

�46 140921 SLEEVE, DRAIN HOSE 1

�47 140072 CLAMP 2

�∇ 701061 ASM., DRAIN PLUG 1

�48 140955 PLUG, DRAIN HOSE 1

�49 140056 WASHER, FENDER 1

�50 230882 STRAP, RUBBER 1

�51 230831 KNOB, DRAIN HOSE 1

52 608616 TANK, RECOVERY, GREEN 1

53 230949 PLATE, LATCH 1



56 140226 SCREW, 5/16–18X5/8 4

57 900105 BAG, CLOTH FILTER 1

58 900102 BAG, PAPER (PKG OF 10) 1


60 140287 SCREW, M4X.7X16MM 4


62 140288 NUT, LOCK 4

63 230482.BK BRACKET, SUPPORT 1


65 608186 DECAL, NOBLES LOGO 1

66 608494 DECAL, ”TYPHOON 16B” 2

N/S 120649 DECAL, WARNING 1

∇ Assembly

� Included in Assembly

PARTS LIST

Typhoon� 16B (04–98)16

LOWER HOUSING PARTS

15

4

5

32

1

2627

28

29

14

13121110

8

9

1617

18

19

20

21

30

6

2423

22

7

25

33

31

32

34

37

36

35

PARTS LIST

Typhoon� 16B (07–99) 17

LOWER HOUSING PARTS LIST


1 230950 BRACKET, SQUEEGEE MOUNT 2


3 140553 SCREW, 1/4–20X1/2 4

4 27833 PLUG, CONNECTOR 1

5 140827 SCREW, 6–32X3/4 2

6 140885 SCREW, 1/4–20X1/2 2

7 608820 HOUSING, BASE, GREEN 1

8 130110 BUSHING, STAIN RELIEF 1

9 240220 GROMMET 1

10 130385 ASM. WIRE 14/2X45” 1

11 140304 CLAMP 1


13 140825 SCREW, #6X1/2 1

14 160630 HOSE, VACUUM 1

15 130364 CABLE, BATTERY 1

16 140801 SCREW, 8–32X3/8 4



19 103065 CASTER, SWIVEL 4” 2



21 140226 SCREW, 5/16–18X5/8 4

22 140553 SCREW, 1/4–20X1/2 4


24 230746 BRACKET, AXLE 2

25 230953 AXLE 1



28 103009 WHEEL 2


30 578244000 WASHER, LOCK 2

31 701163 ASM WIRE #14X17” RED 3/8” XAC 1

32 701164 ASM WIRE #14X22” BLK 5/16” XAC 1

33 140019 WASHER, EXTERNAL LOCK TOOTH 2

34 130869 BATTERY, 12V 130AH 2

35 140201 SCREW, 3/8–16X3/4 2

36 140017 WASHER, LOCK 3/8 2

37 140028 WASHER, FLAT 3/8 2

N/S 130948 CHARGER, 24VDC 15AMP 1

OPTIONS

Typhoon� 16B (11-95)18

ACCESSORY KITS

1

3

2

2


1 190108 KIT, SQUEEGEE, 660 mm (26 in) 1

190972 KIT, SQUEEGEE, 840 mm (33 in) 1

190958 KIT, SQUEEGEE, 990 mm (39 in) 1

2 16593 ∇ KIT, ACCESSORY TOOL 1

6108.1 �Two Piece Wand 1

6117 �Dusting Brush 1

6057 �100 mm (4 in) Upholstery Tool 1

6170 �Crevice Tool 1

14043 �410 mm (16 in) Floor Tool 1

13840 �Squeegee Tool 1


3 190142 ∇ KIT, ACCESSORY TOOL 1

190722 �Two Piece Wand 1

603840 �360 mm (14 in) Carpet Tool ScallopedFace

1

13840 �360 mm (14 in) Squeegee Tool 1

SQUEEGEE KIT BREAKDOWN


∇ 190108 Squeegee Kit 670 mm (26 in) 1

190972 Squeegee Kit 840 mm (33 in) 1

190958 Squeegee Kit 990 mm (39 in) 1

�1 230453.BK Weldment, Squeegee Lift 1

�2 230456 Pedal, Lift 1

�3 230454 Bracket, Squeegee Mount 1

�4 140232 Screw, 3/8–16x1-1/4 1

�5 140925 Spacer, 3/16 1

�6 140028 Washer, Flat 3/8 1

�7 140515 Nut, Lock Nylon 3/8-16 1

�8 630258 Pin, Clevis 3

�9 612254000 Pin, Hair 3

�10 102560 Pad, nonstick 1

�11 160462 Hose, Vacuum 1.5x33” 1

�12 602831 Asm., Squeegee 670 mm (26 in) 1�

603494 Asm., Squeegee 840 mm (33 in) 1

603496 Asm., Squeegee 990 mm (39 in) 1

�13 230727.BK Weldment, Squeegee 670 mm (26 in) 1�

230682.BK Weldment, Squeegee 840 mm (33 in) 1

230692.BK Weldment, Squeegee 990 mm (39 in) 1


�14 100150 Gasket 1

�15 230725.BK Plate, Rear 670 mm (26 in) 1�

230669.BK Plate, Rear 840 mm (33 in) 1

230685.BK Plate, Rear 990 mm (39 in) 1

�16 230723.BK Plate, Front 670 mm (26 in) 1�

230670.BK Plate, Front 840 mm (33 in) 1

230686.BK Plate, Front 990 mm (39 in) 1

�17 603659 Blade, Squeegee 670 mm (26 in) 2�

603661 Blade, Squeegee 840 mm (33 in) 2

603662 Blade, Squeegee 990 mm (39 in) 2

�18 140890 Screw, 10-24x1/2 18�28

�19 140018 Washer, #10 Int Lock 18�28

�20 27257 Knob, Squeegee 2

�21 140221 Screw, 5/16-18x1-1/4 2

�22 630450 Wheel 2

�23 140799 Screw, 5/16-18x1-1/2 2

�24 700844 Asm., Squeegee Roller 2

�25 140226 Screw, 5/16-18x5/8 2

�26 140015 Washer, Lock 2

∇ Assembly

� Included in Assembly

OPTIONS

Typhoon� 16B (04–98) 19

SQUEEGEE KIT BREAKDOWN

10

13

23

16

15

14

21

24

26

25

17

20

1722

1918

11

1

3

8

9

8

9

4

56

7

2

Factory Installedon Machine.

12

Typhoon 16B (Nobles Wet/Dry Vacuum) · PDF fileOPERATION Typhoon 16B (07–99) 3 SAFETY...

Documents

Transcript of Typhoon 16B (Nobles Wet/Dry Vacuum) · PDF fileOPERATION Typhoon 16B (07–99) 3 SAFETY...