TYPES OF INSULATION MATERIAL AND SIZES

ETHYLENE UNIT-10

MAY 2013

No. 2

TYPES OF INSULATION

Insulation Desired purpose Code & Thickness

Cold Insulation Cxx Anti Sweat (Dew point temperature) Axx Dual Temperature Dxx Full Heat Conservation Fxx Acoustic Nxx (NINxx) Personal Protection PPxx

XX stands for insulation thickness in mm.

COLD INSULATION CXX

INSULATION TYPE

No. 4

• Pipe painted Surface• Insulation Polyisocyanurate (PIR)

Measured 25mm.• Caulking between Segments• Mastic Vapor Barrier• Aluminum JacketNote: Insulation material could be either Foam Glass or Polyisocyanurate (PIR)

COLD INSULATION C25

No. 5

• Pipe painted Surface• Insulation Polyisocyanurate (PIR)• Caulking between Segments• Mastic Vapor Barrier• Aluminum Jacket

• Polyisocyanurate Measured 40mmNote: Insulation material could be either Foam Glass or Polyisocyanurate (PIR)

COLD INSULATION C40

No. 6

• Pipe painted Surface• Insulation Polyisocyanurate (PIR)• Caulking between Segments• Mastic Vapor Barrier• Aluminum Jacket

• Polyisocyanurate Measured 50mmNote: Insulation material could be either Foam Glass or Polyisocyanurate (PIR)

COLD INSULATION C50

No. 7

COLD INSULATION C65

• Pipe painted Surface• Insulation Polyisocyanurate

(PIR)• Caulking between Segments• Mastic Vapor Barrier• Aluminum Jacket• Polyisocyanurate Measured

50mmNote: Insulation material could

be either Foam Glass or Polyisocyanurate (PIR)

No. 8

COLD INSULATION C75

• Pipe painted Surface• Insulation Polyisocyanurate

(PIR)• Caulking between Segments• Mastic Vapor Barrier• Aluminum Jacket• Polyisocyanurate Measured

75mmNote: Insulation material could

be either Foam Glass or Polyisocyanurate (PIR)

ANTI SWEAT INSULATION AXX

INSULATION TYPES

No. 10

• Pipe painted Surface• Insulation Polyisocyanurate (PIR)

Measured 25mm.• Caulking between Segments• Mastic Vapor Barrier• Aluminum JacketNote: Insulation material Foam Glass should not be used for Anti Sweat Service

ANTI SWEAT INSULATION A25

DUAL TEMPERATURE INSULATION CXX

INSULATION TYPES

No. 12

• Pipe painted Surface• Fiber Glass Blanket• Foam Glass / Cellular Glass• Caulking between Foam Glass Segments• Mastic Vapor Barrier• Aluminum Jacket

• Measured Total 60mm Thickness• Fiber Glass 20mm• Foam Glass 40mm• As per YANPET Spec Fiber Glass shall

be Minimum 40mm Thick• Note: No PIR should use

DUAL TEMPERATURE INSULATION D65

FULL HEAT CONSERVATION INSULATION FXX

INSULATION TYPES

No. 14

FULL HEAT CONSERVATION F25

• Pipe painted Surface• Insulation Mineral Wool

Block Type 40mm Thickness

• Aluminum Jacket

No. 15

FULL HEAT CONSERVATION F40

• Pipe painted Surface• Insulation Mineral Wool Block Type

40mm Thickness• Aluminum Jacket

• Measured single layer 40mm Thickness

No. 16

• Pipe painted Surface• Insulation Mineral Wool Block Type

50mm Thickness• Aluminum Jacket

• Measured single layer 60mm Thickness

FULL HEAT CONSERVATION F50

ACOUSTIC NOISE INSULATION NXX (NINXX)

INSULATION TYPES

No. 18

ACOUSTIC NOISE INSULATION COLD 25C & 50N (NIN30)

No. 19

• Pipe painted Surface• Insulation Mineral Wool Block Type

100mm Thickness• Polyisocyanurate (PIR)• Mastic Vapor Barrier• Aluminum Jacket with Lead loaded

• Lead loaded Aluminum Jacket

• Note: I believe Insulation order (mineral wool & PIR) should be vise versa

ACOUSTIC NOISE INSULATION COLD C40 & N100 (NIN35)

No. 20

• Mineral Wool Measured 100mm • Polyisocyanurate Measured 40mm

ACOUSTIC NOISE INSULATION COLD C40 & N100 (NIN35)

No. 21

• Pipe painted Surface• Insulation Mineral Wool Block Type

50mm Thickness• Vinyl Loaded Barrier• Aluminum Jacket

• Measured single layer 50mm Thickness

ACOUSTIC NOISE INSULATION HOT N50 (NIN30)

No. 22

• Pipe painted Surface• Insulation Mineral Wool Block Type

125mm (40+85) Thickness• Vinyl Loaded Barrier• Aluminum Jacket

Measured Thickness 45mm each layer

ACOUSTIC NOISE INSULATION HOT N100 (NIN40)

No. 23

• Pipe painted Surface• Insulation Mineral Wool Block Type

125mm (40+85) Thickness• Vinyl Loaded Barrier• Aluminum Jacket

• NIN 40mm thickness Measured

ACOUSTIC NOISE INSULATION HOT N125 (NIN40)

PERSONAL PROTECTION INSULATION PXX

INSULATION TYPE

No. 25

PERSONAL PROTECTION PP25

• Pipe painted Surface

• Insulation Mineral Wool Blanket 25mm Thickness

• Aluminum Jacket

DIVIDER TEXTPRESENTATION RUNNING HEAD

No. 27

CREATE ONE LINE HEADLINES 20PT ARIAL, CAPITALS

Use 16pt Arial Regular for all paragraph text and bullet points. You can increase text size to 18pt or 20pt, but you must keep to one text size throughout your presentation to make it more consistent and seamless. All text should have a line spacing of 1.0, and paragraphs are separated with a Return. Bullets have an additional 0.36 lines of space before each line.• Press the Increase list level icon on the ‘Paragraph’ group to generate a bullet• Press Return to get another bullet• Do not use additional levels of sub-bullets, even though the slide master supports

five levels