TT-6006A and TT-6007A Message terminal - The AST … 6006...TT-6006A and TT-6007A Message Terminal...

TT-6006A and TT-6007AMessage terminal

INSTALLATION MANUAL

TT-6006A and TT-6007AMessage Terminal

Installation manual

Document number: 98-130088-B

Release date: March 16, 2010

Disclaimer

Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information purposes only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g. from http://www.thrane.com or from the distributor. Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source.

Copyright

© 2010 Thrane & Thrane A/S. All rights reserved.

Trademark Acknowledgements

• Thrane & Thrane is a registered trademark of Thrane & Thrane A/S in the European Union and the United States.

• Inmarsat is a registered trademark of the International Maritime Satellite Organisation (IMSO) and is licensed by IMSO to Inmarsat Limited and Inmarsat Ventures plc.

• Other product and company names mentioned in this manual may be trademarks or trade names of their respective owners.

http://www.thrane.com

Safety summary 1

The following general safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the equipment. Thrane & Thrane assumes no liability for the customer's failure to comply with these requirements.

GROUND THE EQUIPMENTTo minimise shock hazard, the equipment chassis and cabinet must be connected to an electrical ground and the cable instructions must be followed.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHEREDo not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite safety hazard.

KEEP AWAY FROM LIVE CIRCUITSOperating personnel must not remove equipment covers. Component replacement and internal adjustment must be made by qualified maintenance personnel.

DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT Because of the danger of introducing additional hazards, do not substitute parts or perform any unauthorized modification to the equipment.

COMPASS SAFE DISTANCEMinimum safety distance: 1 m from the Message Terminal

Failure to comply with the rules above will void the warranty!

iii

About the manual 2

Intended readers

This manual is an installation manual for the Message Terminal. The manual is intended for installers of the Message Terminal and service personnel. Personnel installing or servicing the system must be properly trained and authorized by Thrane & Thrane. It is important that you observe all safety requirements listed in the beginning of this manual, and install the system according to the guidelines in this manual.

Manual overview

Note that this manual does not cover how to use the system. For information on usage refer to the user manual for the system in which you are using the Message Terminal.

This manual has the following chapters:

• Installation gives an introduction to the two types of Message Terminal, explains how to mount the units and gives guidelines for storage and repacking for shipment.

• Connectors and controls shows outline and pin-out for all connectors on the Message Terminal and explains the functions of the buttons in the front panel.

iv

Table of Contents

Chapter 1 Installation

In this chapter .................................................................... 1

The Message Terminal .......................................................2

Initial inspection ................................................................4

Installation .........................................................................5

Storage ..............................................................................7

Repacking for shipment .....................................................7

Chapter 2 Connectors and controls

In this chapter ....................................................................9

Connectors ....................................................................... 10

Buttons in the front panel ................................................ 23

App. A Specifications

In this chapter ..................................................................25

General specifications ......................................................25

App. B Mechanical outlines

In this chapter .................................................................. 27

Outline drawing: Bottom, front and top ............................28

Outline drawing: Rear ......................................................29

Outline drawing: Side and perspective view .....................30

Outline drawing: Flush mount plate ..................................31

Outline drawing: Cable Relief Plate .................................. 32

v

Table of Contents

Glossary .........................................................................................33

Index .........................................................................................37

vi

Chapter 11111

Inst

alla

tion

Installation 1

In this chapter

This chapter provides a short description of the two types of Message Terminal, including descriptions of:

• The Message Terminal

• Initial inspection

• Installation

• Storage and

• Repacking for shipment

1

Chapter 1: Installation

The Message Terminal

GMDSS or general purpose terminal

There are two variants of the Message Terminal: The TT-6006A and the TT-6007A. The only visible difference is the Distress button on the TT-6006A, which is a GMDSS approved terminal. The next sections describe the two terminals.

TT-6006A

The TT-6006A Message Terminal is a maritime terminal for use in GMDSS installations, providing several types of interfaces for connection to external equipment, such as a Mini-C transceiver, MF/HF Radio Telex applications and an Alarm panel. The Message Terminal has a touch-screen for operating the terminal. However, in GMDSS installations a keyboard is mandatory. A suitable keyboard is available from Thrane & Thrane.

2 The Message Terminal

Chapter 1: Installation1111

Inst

alla

tion

TT-6007A

The TT-6007A Message Terminal is a general purpose maritime terminal, e.g. for fishery e-log using third party software. It provides several types of interfaces for connection to external equipment, such as a Mini-C transceiver or BGAN terminal, an ethernet switch and a printer. The Message Terminal has a touch-screen for operating the terminal. You may also connect an external keyboard and mouse/trackball.

The Message Terminal 3


Initial inspection

Inspect the shipping carton immediately upon receipt for evidence of mishandling during transport. If the shipping carton is severely damaged or water stained, request that the carrier's agent be present when opening the carton. Save the carton packing material for future use.

Check that the contents of the shipment are according to the enclosed packing list. If the contents are incomplete, if there is mechanical damage or defect, or if the Message Terminal does not work properly, notify your dealer.

After unpacking the Message Terminal, inspect it thoroughly for hidden damage and loose components or fittings.

Warning! To avoid electrical shock, do not apply power to the Message Terminal if there is any sign of shipping damage to any part of the front or rear panel or the outer cover. Read the safety summary at the front of this manual before installing or operating the Message Terminal.

4 Initial inspection


Inst

alla

tion

Installation

Cable requirements

All cables attached to the Message Terminal must be shielded. Every shield should have a low impedance connection to an electrical ground.

For information on connectors, see Connectors on page 10.

Before using the Message Terminal for the first time, check that all cables are correctly wired and fastened.

Mounting

Mounting the cable relief plate

Before installing the Message Terminal, mount the cable relief plate on the connector panel as shown below using the 2 screws included with the cable relief plate. For outline drawings of the Cable Relief Plate, see Outline drawing: Cable Relief Plate on page 32.

Installation 5


Flush mount

You can flush mount the Message Terminal in a console by using the 4 screw holes (A) on the back of the terminal. The holes are M4 x 10 mm. For a drawing of the Flush-mount plate with panel cut-out and mounting holes, see Outline drawing: Flush mount plate on page 31.

Wall or desktop mounting

You can mount the Message Terminal on a horizontal surface or a vertical surface using the optional mounting bracket. Do as follows:

1. Use the four holes in the mounting bracket to fasten the terminal to the mounting surface. Screws are included with the mounting bracket.

2. Adjust the angle in steps of 7.5° by loosening the hand wheels slightly and moving the Message Terminal into the wanted position. Remember to tighten the hand wheels again.

Please refer to chapter B, Mechanical outlines, describing the detailed mechanical outlines of the Message Terminal and mounting bracket.

6 Installation


Inst

alla

tion

Storage

The Message Terminal may be stored or shipped in temperatures between -40° C and +80° C. Protect the Message Terminal from extreme temperature variation which can cause condensation.

We recommend that you unpack the Message Terminal immediately on delivery.

Repacking for shipment

The shipping carton has been carefully designed to protect the Message Terminal and its accessories during shipment. This carton and its associated packing material should be used when repacking for shipment. Attach a tag indicating the type of service required, return address, model number and full serial number. Mark the carton FRAGILE to ensure careful handling.

If the original shipping carton is not available, the following general instructions should be used for repacking with commercially available material.

1. Wrap the Message Terminal in heavy paper or plastic. Attach a tag indicating the type of service required, return address, model number and full serial number.

2. Use a strong shipping container, e.g. a double walled carton of 160 kg test material.

3. Protect the front- and rear panel with cardboard and insert a 7 cm to 10 cm layer of shock-absorbing material between all surfaces of the equipment and the sides of the container.

4. Seal the shipping container securely.

5. Mark the shipping container FRAGILE to ensure careful handling.

Storage 7


8 Repacking for shipment

Chapter 222

22

Conn

ecto

rs a

nd c

ontro

ls

Connectors and controls 2

In this chapter

This chapter provides a description of all connectors and controls on the Message Terminal. It has the following sections:

• Connectors

• Buttons in the front panel

9

Chapter 2: Connectors and controls

Connectors

Overview

The drawing below shows the connectors on the Message Terminal.

4 x USB Ethernet

Ground

RS-232

DC Powerinput

USB CAN-bus

NMEA 183

2 x NMEA 183 Listener

Talker

Memory cardholder SDHC

Handset orHand microphone

Stereo audiooutput

10 Connectors

Chapter 2: Connectors and controls2

22

2

Conn

ecto

rs a

nd c

ontro

ls

USB interface

Overview

There are four USB Host interface ports (USB Type A) in the rear panel of the Message Terminal and one at the bottom of the front panel.

The applications for the USB ports are as follows:

• Front panel USB port: Temporary connection of mass storage devices

• Rear panel: One for printer, one for keyboard and two for general use.

Connectors 11


Pin-out

The USB connectors are USB Type A. The figure and table below show the connector outline, wire colors and pin assignments.

Pin number Pin function Wire color

1 5 V Red

2 D- White

3 D+ Green

4 GND Black

USB Type A socket

12 Connectors


22

2

Conn

ecto

rs a

nd c

ontro

ls

Ethernet interface

Overview

There is one Ethernet (10/100 MB) connector on the rear panel of the Message Terminal. The Ethernet interface can be used for communicating with connected equipment, such as a TT-6081A power supply or an alarm panel.

Pin-out

The figure and table below show the connector outline, pin assignments and wire color.


1 Tx+ white/orange

2 Tx- orange

3 Rx+ white/green

4 Not connected blue

5 Not connected white/blue

6 Rx- green

7 Not connected white/brown

8 Not connected brown

RJ-45 female

Connectors 13


RS-232 interface (X1)

overview

There is one RS-232 DTE connector on the rear panel of the terminal.

Pin-out

The figure and table below show the connector outline and pin assignments.

Pin number Pin function

1 Not Connected

2 RxD (Receive Data) Input

3 TxD (Transmit Data) output

4 DTR (Data Terminal Ready) output

5 GND

6 DSR (Data Set Ready) Input

7 RTS (Request To Send) output

8 CTS (Clear To Send) Input

9 Not Connected

D-Sub, 9 pin male

14 Connectors


22

2

Conn

ecto

rs a

nd c

ontro

ls

NMEA 0183 compatible Talker interface (X2)

Overview

The NMEA 0183 compatible Talker interface complies to IEC 61162-1 and IEC 61162-2. You can select between two speeds: 4800 or 38400 Baud.

Pin-out


Note The NMEA 0183 compatible Talker connector is a custom connector; a matching cable with connector is available from Thrane & Thrane. The cable is 1.80 m long and the part number is 37-131222-A.


1 TA-

2 TB+

3 GND

4 General purpose input

5 General purpose input

Mini Panel lock, 5 pin male

Connectors 15


Accessory interface (X3)

Overview

The Accessory interface connects to e.g. the TT-6201 Handset and the TT-6202 Hand microphone.

Pin-out



1 NC

2 NC

3 NC

4 NC

5 MIC+

6 EARPIECE

7 HOOK/PTT

8 12 V DC output for handset

9 GND

10 GND

Panel lock, 10 pin male

16 Connectors


22

2

Conn

ecto

rs a

nd c

ontro

ls

DC Power input (X4)

Overview

The DC Power input connects to a DC supply with 12 to 24 V DC nominal (10.8 to 32 V DC). The interface also has a “remote on/off” function and an “on/off control” output.

Pin-out

The figure and table below show the connector outline, pin assignments and wire color in the power cable delivered with the Message Terminal.

Note The Power connector is a custom connector; a matching cable with connector is included in the delivery.

Pin number

Pin functionWire color in power cable

1 DC+ (10.8 - 32 V DC) Red

2 DC- (0 V DC) Black

3 ON_IN (see next page)

White

4 ON_OUT(see next page)

Blue

Panel lock, 4 pin male

Connectors 17


Connecting DC power

Connect DC+ (red wire) to DC out + from your DC supply.

Connect DC- (black wire) to DC out - from your DC supply.

Do not connect the white wire nor the blue wire in the power cable, unless you want to use the Remote on/off function or the On/off control function.

Connecting Remote on/off (ON_IN)

With the Remote on/off function you can switch the Message Terminal on and off from a remote location, without using the on/off button on the terminal. To connect the Remote on/off function in the Message Terminal, do as follows:

1. Connect DC+ and DC- as described in the previous section.

2. Connect a switch to the white wire in the power cable (pin 3, ON_IN, in the Power connector.)

3. Connect the other side of the switch to the black wire in the power cable (DC- (0 V DC) in the Power connector), with a resistance below 10 k.

To switch on the Message Terminal, close the switch. When the switch is closed, Pin 3 in the Power connector is connected to DC-.

Connecting On/off control (ON_OUT)

You can use pin 4 in the Power connector (blue wire) to switch other units on and off when the Message Terminal is switched on and off. How to connect this pin depends on the units you connect.

The function of pin 4 is as follows:

• Message Terminal off: Pin 4 is high (DC+ i.e. between 10.8 V DC and 32 V DC).

• Message Terminal on: Pin 4 is low (DC- from the power supply, with 10 k serial resistance)

Note When the remote switch is closed (the Message Terminal is switched on), you cannot use the Power button on the Message Terminal.

18 Connectors


22

2

Conn

ecto

rs a

nd c

ontro

ls

CAN-bus interface (X5)

Overview

The CAN-bus interface in the Message Terminal supports bidirectional communication.

Pin-out

The figure and table below show the connector outline, pin assignments and standard wire colors.

Note The CAN-bus connector is a custom connector; a matching cable with connector is available from Thrane & Thrane.


1 Not connected None

2 CAN_S Red

3 CAN_C Black

4 CAN_H White

5 CAN_L Blue

M12 Panel screw connector5 pin male

Connectors 19


NMEA 0183 compatible Listener interface (X6 and X7)

Overview

The Message Terminal has two NMEA 0183 compatible Listener interfaces, one high speed (X6: 4800/38400 Baud) and one low speed (X7: 4800 Baud).

Pin-out


Note The NMEA 0183 compatible Listener connector is a custom connector; a matching cable with connector is available from Thrane & Thrane. The cable is 1.80 m long and the part number is 37-131223-A.

X7: 4800 Baud

X6: 4800/38400 Baud


1 LA-

2 LB+

3 GND

Mini panel lock, 3 pin male

20 Connectors


22

2

Conn

ecto

rs a

nd c

ontro

ls

Memory card holder, SDHC

Overview

The Message Terminal has a slot where you can insert a memory card of the type SDHC (Secure Digital High Capacity). The memory card slot is located at the bottom of the terminal next to the front USB connector.

Connectors 21


Ground stud

The ground stud is located in the connector panel and is used to connect a ground wire for grounding the Message Terminal.

To connect the Message Terminal to ship ground, do as follows:

1. Connect a ground cable of > 1 m length and > 4 mm2 cross section to the Ground stud and fasten it with the wing nut.

2. Connect the other end of the cable to ship ground.

Important You must connect the Ground stud to ship ground.

22 Connectors


22

2

Conn

ecto

rs a

nd c

ontro

ls

Buttons in the front panel

Overview

The drawing below shows the buttons on the Message Terminal.

Note Only TT-6006A has a Distress button. It is not available on TT-6007A.

Distressbutton

Testbutton

Dimbutton

Mutebutton

Powerbutton

Buttons in the front panel 23


Functions of the buttons

The buttons in the front panel have the following functions:

Control Function

Distress (only on TT-6006A)

The Distress button on the TT-6006A Message Terminal is used in safety systems to send a distress message through a connected transceiver. Refer to the manual for your system for information on the function.

Test The Test button is used to test the lights and sound in the buttons on the Message Terminal.

Dim The Dim button is used to dim the light in the Message Terminal.

Push and hold to dim more/less. Each new push changes direction between more and less.

Mute The mute button is used to mute the Message Terminal and, in some applications, connected equipment. Refer to the manual for your system for details.

Power Without remote on/off:To switch on: Push the buttonTo switch off: Push and hold for 2 secondsIf the Message Terminal cannot switch off normally (e.g. corrupt software): Push and hold for 10 seconds

With remote on/off:To switch on and off: The Power button cannot be used normally; use the remote on/off switch to switch the Message Terminal on and off.To restart the terminal: Push and hold for 2 secondsCorrupt software: Push and hold for 10 seconds to restart

24 Buttons in the front panel

Appendix AAAAA

Spec

ifica

tions

Specifications A

In this chapter

This chapter provides general specifications for the Message Terminal.

General specifications

Item Specifications

CPU • Intel atom based CPU

• SSD (Solid State Drive) for operating system (GNU/Linux or Windows XP embedded), application software and data storage.

Additional storage media

• SD card slot for user data storage (accepts SDHC)

• USB Host interface connector for mass storage devices

Display 10.4” Touch screen, 800 x 600 pixels TFT, LED backlight

Keyboard i/f USB

Printer port USB

Power 10.8 to 32 V DC, with “remote on/off” input and “on/off control” output

Power Consumption

Max. 20 W, typical 12 W

25

Appendix A: Specifications

Interfaces • 4 USB Host interface ports - one for printer, one for keyboard and 2 for general use (all up to 480 MB).

• 1 USB port (front) for external storage (up to 12 MB).

• Ethernet (10/100Mbit), RJ45

• RS232, DB9 male

• Isolated CAN-bus interface

• NMEA 0183 compatible talker, ref. to chassis (secondary gnd)

• NMEA 0183 compatible listener, isolated, 4800 Baud max.

• NMEA 0183 compatible listener, isolated, 4800/38400 Baud max

• Accessory interface for e.g. handset or hand microphone

• Stereo audio output, e.g. for loudspeakers

• One digital input pin for simple active/inactive detection.

Environmental • Meets or exceeds all Inmarsat specifications for the Inmarsat-C Network for SOLAS with distress call functions. (CN114 and IEC 945 requirements).

• Meets CE-marking requirements.

• TT-6006A is Wheelmark approved.

• IP protection class: IP30 on the rear section, IP33 on the front surface.

Ambient Temperature

-25°C to 55°C operating -40°C to 80°C storage.

Compass safe distance

1 m

Dimensions H x W x D

• 233.9 x 268.8 x 59.9 mm without bracket

• 258.8 x 299.6 x 92.3 mm with bracket at vertical position

Weight 2.0 kg without mounting bracket, 2.2 kg with bracket

Item Specifications

26 General specifications

Appendix BBB

BB

Mec

hani

cal o

utlin

es

Mechanical outlines B

In this chapter

This chapter shows outline drawings with the dimensions and weight of the Message Terminal.

27

Appendix B: Mechanical outlines

Outline drawing: Bottom, front and top

2275

3

268.8

258

.8

299.6

92.3

112

.8

273

70

.9

4 x ø4.2

10.4”

NOTE: Distress button only on TT-6006A

28 Outline drawing: Bottom, front and top

Appendix B: Mechanical outlinesB

BB

B

Mec

hani

cal o

utlin

es

Outline drawing: Rear

251.2

216

.3

Weight: 2.0 kg without mounting bracket and wheel knobs

All units are in millimetersA: 4 pcs. M4 x 10Total weight: 2.2 kg

Outline drawing: Rear 29


Outline drawing: Side and perspective view

59.9

70.

3

18

.5

24.9

233

.9

30 Outline drawing: Side and perspective view

Appendix B: Mechanical outlinesB

BB

B

Mec

hani

cal o

utlin

es

Outline drawing: Flush mount plate

(2)

216

.3

4.4ø 4.4 251.2

260

205

5.6

5

4.4ø 4.4

ø 4.4

ø 4.4

5.65

All units are in millimeters

Outline drawing: Flush mount plate 31


Outline drawing: Cable Relief Plate

93

67.8

30.3

32 Outline drawing: Cable Relief Plate

GlossaryCC
Glossary C
CC

Glos

sary

B

BGAN Broadband Global Area Network. A satellite network based on geostationary satellites, delivering data rates of up to 492 kbps to virtually any part of the earth, with full UMTS (3G) compatibility.

C

CAN Controller-Area Network. A vehicle bus standard designed to allow microcontrollers and devices to communicate with each other within a vehicle without a host computer. CAN is a message based protocol, designed specifically for automotive applications but now also used in other areas such as industrial automation and medical equipment.

CPU Central Processing Unit, also known as a processor. The portion of a computer system that carries out the instructions of a computer program, and is the primary element carrying out the computer’s functions.

D

DTE Data Terminal Equipment. Includes Computers, Serial Printers, PLC’s, Video Cameras, Video Recorders, Video Editors, and most devices which are not used to extend communications.

G

GMDSS Global Maritime Distress Safety System. GMDSS consists of several systems, some of which are new, but many of which have been in operation for many years. The system is intended to perform the following functions: alerting (including position determination of the unit in distress), search and rescue coordination, locating (homing), maritime safety information broadcasts, general communications, and bridge-to-bridge communications.

33

Glossary

GNU A computer operating system composed entirely of free software. Its name is a recursive acronym for “GNU’s Not Unix!” This name was chosen because GNU’s design is Unix-like, but differs from Unix by being free software and containing no Unix code.

H

HF High Frequency. Radio frequencies between 3 and 30 MHz. Used for direct, long-distance (often inter-continental) communications.

I

IEC International Electrotechnical Commission. The international standards and conformity assessment body for all fields of electrotechnology.

IMSO International Maritime Satellite Organisation

IP Ingress Protection. EN 60529 outlines an international classification system for the sealing effectiveness of enclosures of electrical equipment against the intrusion into the equipment of foreign bodies (i.e. tools, dust, fingers) and moisture. This classification system uses the letters "IP" ("Ingress Protection") followed by two or three digits. (A third digit is sometimes used. An "x" is used for one of the digits if there is only one class of protection; e.g. IPX4 which addresses moisture resistance only.)

L

LED Light Emitting Diode

34

Glossary CC

CC

Glos

sary

M

MF Medium Frequency. Radio frequencies (RF) in the range of 300 kHz to 3 MHz. Navtex, which is part of the current Global Maritime Distress Safety System occupies 518 kHz and 490 kHz for important digital text broadcasts.

N

NMEA National Marine Electronics Association (standard). A combined electrical and data specification for communication between marine electronic devices such as echo sounder, sonars, anemometer (wind speed and direction), gyrocompass, autopilot, GPS receivers and many other types of instruments. It has been defined by, and is controlled by, the U.S.-based National Marine Electronics Association.

S

SD Secure Digital. A non-volatile memory card format developed by Panasonic, SanDisk, and Toshiba for use in portable devices. Currently it is widely used in digital cameras, digital camcorders, handheld computers, netbook computers, PDAs, media players, mobile phones, GPS receivers, and video games.

SDHC Secure Digital High Capacity. An extension of the SD standard which increases card’s storage capacity up to 32 GB. SDHC cards share the same physical and electrical form factor as older (SD 1.x) cards, allowing SDHC-devices to support both newer SDHC cards and older SD-cards.

SOLAS (International Convention for the) Safety Of Life At Sea. Generally regarded as the most important of all international treaties concerning the safety of merchant ships.

SSD Solid-State Drive. A data storage device that uses solid-state memory to store persistent data. An SSD emulates a hard disk drive interface, thus easily replacing it in most applications.

35

Glossary

T

TFT Thin Film Transistor. A thin film transistor liquid crystal display (TFT-LCD) is a variant of liquid crystal display (LCD) which uses thin-film transistor (TFT) technology to improve image quality (e.g., addressability, contrast).

U

USB Universal Serial Bus. A specification to establish communication between devices and a host controller (usually personal computers). USB is intended to replace many varieties of serial and parallel ports. USB can connect computer peripherals such as mice, keyboards, digital cameras, printers, personal media players, flash drives, and external hard drives.

36

IndexD

Index D

DD

D

Inde

x

A

Accessory connector, 16

B

buttons in front panel, 23Dim, 24Distress, 24Mute, 24Power, 24Test, 24

C

cable reliefmounting, 5outline drawing, 32

cable requirements, 5CAN-bus connector, 19connectors

Accessory, 16CAN-bus, 19DC power input, 17Ethernet, 13hand microphone, 16handset, 16NMEA 0183 compatible Listener, 20NMEA 0183 compatible Talker, 15overview, 10RS-232, 14USB, 11

controls, 23

D

DC power input connector, 17

desktop mounting, 6Dim button, 24Distress button, 24document number

this manual, idrawings

outline, 27

E

Ethernet connector, 13

F

flush mount, 6front panel buttons, 23

G

GMDSS approved Message Terminal, 2ground stud, 22grounding the Message Terminal, 22

H

hand microphone connector, 16handset connector, 16

I

initial inspection, 4installation, 5

37

Index

M

manualdocument number, i

mechanical drawings, 27memory card insert, 21Message Terminal

for general use, 3for safety use, 2types of, 2

mountingcable relief plate, 5flush mount, 6on wall or desktop, 6

Mute button, 24

N

NMEA 0183 Listener connector, 20NMEA 0183 Talker connector, 15

O

outline drawings, 27

P

Power button, 24power input connector, 17

R

repacking for shipment, 7returning units, 7RS-232 connector, 14

38

S

safety summary, iiiSDHC memory card, 21specifications, 25storage, 7

T

Test button, 24TT-6006A description, 2TT-6007A description, 3types of Message Terminal, 2

U

unpacking, 4USB connectors, 11

W

wall mounting, 6

98-130088-B

Thrane & Thrane A/S • [email protected] • www.thrane.com

TT-6006A and TT-6007A Message terminal - The AST … 6006...TT-6006A and TT-6007A Message Terminal...

Documents

Transcript of TT-6006A and TT-6007A Message terminal - The AST … 6006...TT-6006A and TT-6007A Message Terminal...