TSX C USB FIP
Transcript of TSX C USB FIP
ENG
LISH
Table of ContentsSafety Instructions 3
Precautions ....................................................................................................................4
TSX C USB FIP Communication Adapter - Overview 5
Package Content............................................................................................................ 5Required Items............................................................................................................... 5
CE Marking 6
Compatible Models ........................................................................................................6
External Drawings 7
Electrical .........................................................................................................................7Environmental ................................................................................................................ 7
FIP Cable Connection 8
Mounting method 10
FIP cable and USB cable 11
Cable Length ................................................................................................................12
LED Status Indicators 13
If you connected the Adapter Before Installing the Driver 14
Appendix 87
35015331 04 1
Table of contentsEN
GLI
SH
2 35015331 04
ENG
LISH
35015331 04 3
SafetySafety Instructions
Read these instructions carefully, and look at the equipment to become familiar with the device before trying to install, operate, or maintain it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
DISCLAIMER
Electrical equipment should be installed, operated, serviced and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of its material.
© 2008 Schneider Electric. All Rights Reserved.
DANGERDANGER indicates a hazardous situation, which will result in death or serious injury.
WARNINGWARNING indicates a potentially hazardous situation which, if not avoided, can result in death, serious injury, or equipment damage.
CAUTIONCAUTION indicates a potentially hazardous situation, which, if not avoided, can result in personal injury or equipment damage.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that followthis symbol to avoid possible injury or death.
The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists, which can or will result in personal injury if the instructions are not followed.
4 35015331 04
ENG
LISH
SafetyEssential Safety Precautions
Schneider Electric has designed the TSX C USB FIP communication adapter for use in non-hazardous locations only (UL508).
Precautions
Follow these instructions:
• The USB Fip adapter requires 450 mA from the master port. Because of the level of power needed, do not connect the adapter to an USB-Powered hub.
• On a PC or iPC, install the driver (see the appendix) before plugging the TSX C USB FIP communication adapter on a PC (or iPC) USB port. If you are using a Magelis dialog operator, the driver will be downloaded automatically.
• Do not plug the TSX C USB FIP communication adapter if the driver is not installed.
WARNINGRISK OF EXPLOSION
Do not use this unit in an environment where flammable gases are present.Operating this unit in such an environment may cause an explosion.
Failure to follow this instruction can result in death, serious injury, or equipment damage.
CAUTIONENVIRONMENTAL EXPOSURE HAZARD
• Do not allow liquids, metal or charged particles to enter this unit, since they can cause a malfunction.
• Do not use or store this unit in direct sunlight, in excessively dusty or dirty environments or where excessive impact or vibration can occur.
Failure to follow this instruction can result in injury or equipment damage.
ENG
LISH
Introduction
TSX C USB FIP Communication Adapter - Overview
Thank you for purchasing TELEMECANIQUE TSX C USB FIP communication adapter. This unit is designed to provide a bridge between a USB connection and a Fipway Network or a Fipio field bus. It may replace both PCMCIA (TSXFPP20) or ISA card (TSXFPC10) on a PC, Magelis iPC, and Magelis dialog operator.
Package Content
The package contains the following items:
• a TSX C USB FIP communication adapter with a pre-connected USB cable• an Installation guide• a cable bond to fix the FIP cable on the adapter
Required Items
The following items are required to use the adapter:
• a driver to use the adapter with a PC or the iPC (TSX C USB FIP driver, included in the CD driver (ref: TLXCDDRV20M V2.5 or higher)).
• a FIP cable (TSX FP CG010 or TSX FP CG030)
Note : The TSX C USB FIP driver for Windows 2000 and XP is included in the driver pack that you can download from the telemecanique web site. On www.telemecanique.com, click downloads -> Software/Firmware -> Automation -> Modicon Premium and select Driver Pack (V2.5 or higher).
Note : Vijeo Designer automatically provides the driver to use the TSX C USB FIP adapter with a Magelis dialog operator.
35015331 04 5
6 35015331 04
ENG
LISH
General Specification
CE Marking
The TSX C USB FIP is CE marked and EMC compliant.This unit conforms to EN55011 Class A and EN61000-6-2 directives.
Compatible Models
The following tools (hosts) are compatible with the TSX C USB FIP:• Personal Computer• industrial Personal Computer (Magelis iPC and other iPC)• dialog operators (Magelis XBTGT/GK without XBTGT1100 and XBTGT1130)
Note : a maximum of two TSX C USB FIP adapters on one host.
The TSX C USB FIP communication adapter is compatible with the following:-networks or field buses:
• FIPWAY• FIPIO• WorldFIP
-software:• Unity Pro V3.1 or higher• PL7 V4.5 SP4 or higher• OPC Factory Server (OFS) V3.32 or higher• Vijeo Designer V4.6 or higher
ENG
LISH
35015331 04 7
General Specification
External Drawings
The following diagram illustrates the front panel of the TSX C USB FIP and its size.
Electrical
Environmental
Parameter Description
Rated Voltage 5 V DC (supplied by the USB cable)
Power Consumption 2.25 W max (450mA)
Item Description
Ambient Operating Temperature 0 °C to +50 °C (+32 °F to +122 °F)
Storage Temperature -40 °C to +70 °C (-40 °F to +158 °F)
Ambient Humidity 10% RH to 70% RH(No condensing)
Size: 77 x 118 x 33.5 mm (3.03 x 4.65 x 1.32 in)FIP POWER USBERR
Note : The cable to the host and the network is not shown.
8 35015331 04
ENG
LISH
Cable Connection
FIP Cable Connection
To connect the FIP cable:.
Note : Do not remove the grounding bracket screw, it may damage the product when put back in place.
3. Insert the FIP cable with the connector under the grounding bracket.
4. Connect the connector
1. Unscrew the cover fixing screw.
FIP POWER USBERR
2. Loosen, but do not remove, the grounding bracket screw.
USB cable
FIP cable
grounding bracket
USB cable
connector
cable bond
ENG
LISH
35015331 04 9
Cable Connection
5. Tighten the grounding bracket screw.
6. Attach the FIP cable to the adapter using the cable bond.7. Set the cover in place.
AY4x VEAY3.5x VE
flat-head screwdriver
8. Screw in the cover fixing screw.
FIP POWER USBERR
10 35015331 04
ENG
LISH
Mounting method
Mounting method
The following diagram shows how to mount the TSX C USB FIP communication adapter on the DIN rail.
Note : The DIN rail must be electrically connected to earth ground.
Grounding contact
DIN rail connected to
earth ground
20 mm0.78 in.
Strip cable as shown
ENG
LISH
35015331 04 11
Connection
FIP cable and USB cable
In order to use the adapter with a PC or iPC, it is mandatory to install and configure the driver on the host (for more information, refer to the appendix at the end of this document)After installing and configuring the driver:
●1. connect the TSX C USB FIP adapter to the Fipway network (or Fipio network)
●2. connect the adapter to the PC (or iPC) with the USB cable
.
To the PC, iPC or
To the FIP network
Magelis dialog operator
FIP POWER USBERR
12 35015331 04
ENG
LISH
Connection
Cable Length
The USB cable is 2 m (6.562 ft) length. The FIP cable is 1 or 3 meters length:
FIP cable reference Length
TSX FP CG010 1 m (3.281 ft)
TSX FP CG030 3 m (9.843 ft)
CAUTIONIMPROPER HANDLING HAZARD
To prevent damage to the cable connector or the USB port:• When connecting the USB Data Transfer Cable to the PC, industrial PC
or to the Magelis dialog operator, insert the cable’s connector at the correct 90° angle.
• When disconnecting the cable, make sure to hold the connector, not the cable itself.
Failure to follow this instruction can result in injury or equipment damage.
ENG
LISH
35015331 04 13
LED Status
LED Status Indicators
LED Status Meaning
USB yellow Communication on USB cable.
off No communication on USB cable.
POWER green Power is supplied to the adapter.
off No power is supplied to the adapter.
FIP yellow Communication activity on the FIP network.
off No access to the FIP network.
ERR red FIP communication problem:• verify the FIP cable is connected,• disconnect and reconnect the adapter,• modify the station address (driver configuration),• verify the FIP network (end of line adaptation,...).
off No error on the FIP network.
14 35015331 04
ENG
LISH
Wrong Installation
If you connected the Adapter Before Installing the Driver
If you connect the TSX C USB FIP communication adapter on a PC (or iPC) USB port before installing the driver, the adapter will not function. Follow this procedure to make the adapter function normally:
1. right-click on My Computer
2. click Properties
3. select the Hardware tab
4. select Device Manager
5. in Universal Serial Bus controllers, right-click on the faulty device
6. select Uninstall
7. when the uninstall is completed, install the driver (see the appendix) and plug the TSX C USB FIP adapter to a PC (or iPC) USB port.
DEU
TSC
H
35015331 04 15
Inhaltsverzeichnis
Sicherheitshinweise 17
Vorsichtsmaßnahmen.................................................................................................... 19
TSX C USB FIP Kommunikationsadapter - Überblick 20
Packungsinhalt .............................................................................................................. 20Erforderliche Materialien............................................................................................... 20
CE-Zertifizierung 21
Kompatible Modelle ...................................................................................................... 21
Außenansichten 22
Elektrik .......................................................................................................................... 22Umgebungsbedingungen.............................................................................................. 22
FIP-Kabelverbindung 23
Montageverfahren 25
FIP-Kabel und USB-Kabel 26
Kabellänge .................................................................................................................... 27
LED-Statusanzeigen 28
Falls Sie den Adapter vor der Installation des Treibers angeschlossen haben 29
Anhang 87
16 35015331 04
DEU
TSC
HInhaltsverzeichnis
DEU
TSC
H
35015331 04 17
Sicherheit
Sicherheitshinweise
Lesen Sie diese Anweisungen gründlich durch und machen Sie sich mit dem Gerät vertraut, bevor Sie es installieren, in Betrieb nehmen oder warten. Die folgenden Hinweise können an verschiedenen Stellen in dieser Dokumentation enthalten oder auf dem Gerät zu lesen sein. Die Hinweise warnen vor möglichen Gefahren oder machen auf Informationen aufmerksam, die Vorgänge erläutern bzw. vereinfachen.
GEFAHRGEFAHR macht auf eine gefährliche Situation aufmerksam, die unweigerlich einen schweren oder tödlichen Unfall zur Folge hat.
WARNUNGWARNUNG macht auf eine möglicherweise gefährliche Situation aufmerksam, die bei Nichtbeachtung unter Umständen einen schweren oder tödlichen Unfall oder Beschädigungen an Geräten zur Folge haben kann.
VORSICHTVORSICHT macht auf eine möglicherweise gefährliche Situation aufmerksam, die bei Nichtbeachtung unter Umständen Verletzungen oder Beschädigungen an Geräten zur Folge haben kann.
Dies ist ein allgemeines Warnsymbol. Es macht Sie auf möglicheVerletzungsgefahren aufmerksam. Beachten Sie alle unter diesem Symbol aufgeführten Hinweise, um Verletzungen oderUnfälle mit Todesfälle zu vermeiden.
Dieses Symbol in Verbindung mit einem Gefahren- oder Warnhinweis weist auf die Gefahr eines elektrischen Schlags hin,der bei Nichtbeachtung der Anweisungen zu Körperverletzung führen kann
18 35015331 04
DEU
TSC
HSicherheit
HAFTUNGSAUSSCHLUSS
Elektrische Geräte dürfen nur von qualifiziertem Fachpersonal installiert, bedient, instand gehalten und gewartet werden. Schneider Electric übernimmt keine Verantwortung für mögliche Schäden, die aus der Verwendung dieses Materials entstehen.
© 2008 Schneider Electric. Alle Rechte vorbehalten.
Grundlegende Sicherheitsmaßnahmen
Schneider Electric hat den TSX C USB FIP-Kommunikationsadapter ausschließlich für die Verwendung in nicht gefährlichen Umgebungen konzipiert (UL508).
WARNUNGEXPLOSIONSGEFAHR
Dieses Gerät darf nicht in Bereichen mit entflammbaren Gasen eingesetzt werden. Der Betrieb dieses Geräts in einer solchen Umgebung kann zu einer Explosion führen.
Die Nichtbeachtung dieser Anweisung kann zu Tod, schweren Verletzungen oder Materialschäden führen.
VORSICHTGEFAHR DURCH UMGEBUNGSEINFLÜSSE
• Vermeiden Sie das Eindringen von Flüssigkeiten, Metall- oder geladenen Partikeln in dieses Gerät, da diese zu einer Fehlfunktion führen können.
• Verwenden oder Lagern Sie das Gerät nicht bei direkter Sonneneinstrahlung, in übermäßig staubigen oder verschmutzten Umgebungen oder an Orten, an denen das Gerät Stößen oder Vibrationen ausgesetzt ist.
Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschaden zur Folge haben.
DEU
TSC
H
35015331 04 19
Einführung
Vorsichtsmaßnahmen
Befolgen Sie die nachfolgend aufgeführten Vorschriften:
• Der USB Fip-Adapter erfordert 450 mA vom Master-Port. Schließen Sie den Adapter aufgrund der erforderlichen Stromstärke nicht an einen USB-gespeisten Hub an.
• Installieren Sie den Treiber auf einem PC oder iPC (siehe Anhang), bevor Sie den TSX C USB FIP-Kommunikationsadapter am USB-Port des PC (bzw. iPC) anschließen. Wenn Sie ein Magelis-Bediener-Terminal verwenden, wird der Treiber automatisch geladen.
• Schließen Sie den TSX C USB FIP-Kommunikationsadapter nicht an, wenn der Treiber nicht installiert ist.
20 35015331 04
DEU
TSC
HAllgemeine Kenndaten
TSX C USB FIP Kommunikationsadapter - Überblick
Vielen Dank für den Erwerb eines TELEMECANIQUE TSX C USB FIP-Kommunikationsadapters. Dieses Gerät dient als Bridge zwischen einem USB-Anschluss und einem Fipway-Netzwerk oder einem Fipio-Feldbus. Er kann sowohl die PCMCIA- (TSXFPP20) als auch die ISA-Karte (TSXFPC10) in einem PC, Magelis iPC, und Magelis-Dialog-Terminal ersetzen.
Packungsinhalt
Dieses Paket enthält die folgenden Komponenten:
• einen TSX C USB FIP Kommunikationsadapter mit bereits angeschlossenem USB-Kabel
• ein Installationshandbuch• ein Kabelmantelverbinder zur Befestigung des FIP-Kabels am Adapter
Erforderliche Materialien
Die folgenden Materialien sind für die Verwendung des Adapters erforderlich:
• ein Treiber, um den Adapter mit einem PC oder dem iPC zu verwenden (TSX C USB FIP-Treiber, enthalten auf der Treiber-CD-ROM (Ref.: TLXCDDRV20M V2.5 oder höher)).
• ein FIP-Kabel (TSX FP CG010 oder TSX FP CG030)
Hinweis: Der TSX C USB FIP-Treiber für Windows 2000 znd XP ist im Treiber-Paket enthalten, das Sie von der Telemecanique-Website herunterladen können. Klicken Sie unter www.telemecanique.com auf downloads -> Software/Firmware -> Automation -> Modicon Premium und wählen Sie Driver Pack (V2.5 oder höher) aus.
Hinweis: Vijeo Designer stellt automatisch den Treiber für die Verwendung des TSX C USB FIP-Adapters mit einem Magelis-Dialog-Terminal bereit.
DEU
TSC
H
35015331 04 21
Allgemeine Kenndaten
CE-Zertifizierung
Das TSX C USB FIP ist ein CE zertifiziertes, EMV-konformes Produkt.Dieses Gerät entspricht den Normen EN55011 Klasse A und EN61000-6-2.
Kompatible Modelle
Die folgenden Tools (Hosts) sind mit dem TSX C USB FIP kompatibel:• Personal Computer• industrieller Personal Computer (Magelis iPC und andere iPC)• Dialog-Terminals (Magelis XBTGT/GK ohne XBTGT1100 und XBTGT1130)
Hinweis: maximal zwei TSX C USB FIP-Adapter an einem Host.
Der TSX C USB FIP-Kommunikationsadapter ist mit folgenden Komponenten kompatibel:-Netzwerke oder Feldbusse:
• FIPWAY• FIPIO• WorldFIP
-Software:• Unity Pro V3.1 oder höher• PL7 V4.5 SP4 oder höher• OPC Factory Server (OFS) V3.32 oder höher• Vijeo Designer V4.6 oder höher
22 35015331 04
DEU
TSC
HKabel- verbindung
Außenansichten
Das nachfolgende Schema zeigt die Frontseite des TSX C USB FIP. und deren Größe.
Elektrik
Umgebungsbedingungen
Parameter Beschreibung
Nennspannung 5 V DC (Speisung über das USB-Kabel)
Stromverbrauch max. 2,25 W (450 mA)
Element Beschreibung
Betriebstemperatur 0 °C bis +50 °C (+32 °F bis +122 °F)
Lagertemperatur -40 °C bis +70 °C (-40 °F bis +158 °F)
Luftfeuchtigkeit 10 % bis 70 % rel. Luftfeuchtigkeit(keine Kondensation)
Größe: 77 x 118 x 33,5 mm (3,03 x 4,65 x 1,32 in)
FIP POWER USBERR
Hinweis: Das Kabel zum Host und zum Netzwerk wird nicht abgebildet.
DEU
TSC
H
35015331 04 23
Kabel-verbindung
FIP-Kabelverbindung
Vorgehensweise für den Anschluss des FIP-Kabels:.
Hinweis: Entfernen Sie die Schraube des Erdungshalters nicht. Sie kann beim erneuten Einschrauben zu einer Beschädigung des Produkts führen.
3. Führen Sie das FIP-Kabel mit dem Stecker unter dem Erdungshalter durch.
4. Schließen Sie den Stecker an.
1. Lösen Sie die Befestigungsschraube
der Abdeckung.
FIP POWER USBERR
2. Lösen Sie die Schraube des
Erdungshalters, aber entfernen Sie sie nicht.
USB-Kabel
FIP-Kabel
Erdungshalter
USB-Kabel
Stecker
Kabelmantelverbinder
24 35015331 04
DEU
TSC
HKabel-verbindung
5. Ziehen Sie die Schraube des Erdungshalters an.
6. Befestigen Sie das FIP-Kabel am Adapter mithilfe des Kabelmantelverbinders.7. Bringen Sie die Abdeckung an.
AY4x VEAY3,5x VE
Flachkopf-Schraubendreher
8. Schrauben Sie die Befestigungsschraube
der Abdeckung fest.
FIP POWER USBERR
DEU
TSC
H
35015331 04 25
Verbindung
Montageverfahren
Die folgende Abbildung zeigt die Montate des TSX C USB FIP-Kommunikationsadapter an der DIN-Schiene.
Hinweis: Die DIN-Schiene muss geerdet sein.
Erdungskontakt
Geerdete DIN-Schiene
20 mm0.78 in.
Kabel wie gezeigt abisolieren
26 35015331 04
DEU
TSC
HVerbindung
FIP-Kabel und USB-Kabel
Um den Adapter mit einem PC oder iPC zu nutzen, muss der Treiber auf dem Host installiert und konfiguriert werden (weitere Informationen finden Sie im Anhang am Ende dieses Dokuments).Vorgehensweise nach der Installation und Konfiguration des Treibers:
●1. Schließen Sie den Adapter TSX C USB FIP an das Fipway-Netzwerk (oder an das Fipio-Netzwerk) an.
●2. Verbinden Sie den Adapter mittels des USB-Kabels mit dem PC (oder iPC).
.
Zum PC, iPC oder
Zum FIP-Netzwerk
Magelis-Bediener-Terminal
FIP POWER USBERR
DEU
TSC
H
35015331 04 27
Verbindung
Kabellänge
Das USB-Kabel ist 2 m (6,562 ft) lang. Das FIP-Kabel ist 1 oder 3 Meter lang.:
FIP-Kabelreferenz Länge
TSX FP CG010 1 m (3,281 ft)
TSX FP CG030 3 m (9,843 ft)
VORSICHTGEFAHR BEI FALSCHER HANDHABUNG
Befolgen Sie das unten aufgeführte Verfahren, um eine Beschädigung des Kabelsteckers oder des USB-Ports zu vermeiden:• Achten Sie beim Anschluss des USB-Datenübertragungskabels an den
PC, industriellen PC oder an das Magelis-Bediener-Terminal darauf, den Stecker des Kabels in einem Winkel von 90° einzusetzen.
• Halten Sie beim Trennen des Kabels den Stecker und nicht das Kabels selbst fest.
Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschaden zur Folge haben.
28 35015331 04
DEU
TSC
HLED-Status
LED-Statusanzeigen
LED Status Bedeutung
USB Gelb Kommunikation über das USB-Kabel
aus Keine Kommunikation über das USB-Kabel
POWER grün Adapter spannungsversorgt
aus Adapter nicht spannungsversorgt
FIP Gelb Kommunikationstätigkeit im FIP-Netzwerk
aus Kein Zugriff auf das FIP-Netzwerk
ERR Rot FIP-Kommunikationsproblem:• Überprüfen Sie, ob das FIP-Kabel angeschlossen ist.• Trennen Sie den Adapter und schließen Sie ihn
wieder an.• Ändern Sie die Stationsadresse
(Treiberkonfiguration).• Überprüfen Sie das FIP-Netzwerk
(Leitungsendanpassung etc.).
aus Kein Fehler auf dem FIP-Netzwerk
DEU
TSC
H
35015331 04 29
Falsche Installation
Falls Sie den Adapter vor der Installation des Treibers angeschlossen haben
Wenn Sie den TSX C USB FIP-Kommunikationsadapter an den USB-Port eines PC (oder iPC) anschließen, bevor Sie den Treiber installiert haben, ist der Adapter nicht funktionsfähig. Befolgen Sie das nachfolgend aufgeführte Verfahren, um die Funktionsfähigkeit des Adapters wieder herzustellen.
1. Klicken Sie mit der rechten Maustaste auf Arbeitsplatz.
2. Klicken Sie auf Eigenschaften.
3. Wählen Sie die Registerkarte Hardware aus.
4. Wählen Sie Geräte-Manager aus.
5. Klicken Sie unter Universelle serielle Bus-Controller mit der rechten Maustaste auf das fehlerhafte Gerät.
6. Wählen Sie Deinstallieren aus.
7. Wenn die Deinstallation abgeschlossen ist, installieren Sie den Treiber (siehe Anhang) und schließen Sie den TSX C USB FIP-Adapter an den USB-Port eines PC (oder iPC) an.
30 35015331 04
DEU
TSC
HSicherheit
FRA
NC
AIS
Table des matières
Consignes de sécurité 33
Précautions à observer ................................................................................................34
Adaptateur de communication TSX C USB FIP - Présentation 35
Contenu de l'emballage ...............................................................................................35Eléments requis ...........................................................................................................35
Marquage CE 36
Modèles compatibles ...................................................................................................36
Schémas externes 37
Electricité .....................................................................................................................37Environnement .............................................................................................................37
Connexion du câble FIP 38
Modalités de montage 40
Câble FIP et câble USB 41
Longueur des câbles ....................................................................................................42
Etat des voyants 43
Branchement de l'adaptateur avant que le pilote ne soit installé 44
Annexe 87
35015331 04 31
Table des matières
FRAN
CA
IS
32 35015331 04
FRA
NC
AIS
35015331 04 33
Sécurité
Consignes de sécurité
Veuillez lire attentivement ces consignes, examiner l'appareil et vous familiariser avec cet équipement avant son installation, son fonctionnement ou son entretien. Les messages particuliers qui suivent peuvent apparaître dans la documentation ou sur l'appareil. Ils vous avertissent de dangers potentiels ou attirent votre attention sur des informations susceptibles de clarifier ou de simplifier une procédure.
AVIS DE NON-RESPONSABILITE
Le matériel électrique doit être installé, utilisé, réparé et entretenu uniquement par du personnel qualifié. Schneider Electric n'assume aucune responsabilité des conséquences éventuelles découlant de l'utilisation de cette documentation.
© 2008 Schneider Electric. Tous droits réservés.
DANGERDANGER indique une situation dangereuse qui entraînera la mort ou des blessures graves.
AVERTISSEMENTAVERTISSEMENT indique une situation susceptible de provoquer la mort, des blessures graves ou des dommages matériels.
ATTENTIONATTENTION indique une situation susceptible de provoquer des blessures corporelles ou des dommages matériels.
Ceci est le symbole d'une alerte de sécurité. Il vous avertit d'un risque de blessures corporelles. Respectez scrupuleusementles consignes de sécurité associées à ce symbole pour éviterde vous blesser ou de mettre votre vie en danger.
La présence de ce symbole sur un panneau de sécurité Danger ou Avertissement signale un risque électrique pouvant entraînerdes lésions corporelles en cas de non-respect des consignes.
34 35015331 04
FRA
NC
AIS
Sécurité
Précautions concernant la sécurité
Schneider Electric a conçu l'adaptateur de communication TSX C USB FIP pour une utilisation dans des environnements non dangereux uniquement (UL508).
Précautions à observer
Veuillez respecter les consignes suivantes :
• L'adaptateur USB FIP doit recevoir 450 mA du port maître. Etant donné le niveau d'alimentation requis, vous ne devez en aucun cas connecter l'adaptateur à un concentrateur alimenté par le port USB de l’hôte.
• Sur un PC ou un iPC, installez le pilote (voir annexe) avant de brancher l'adaptateur de communication TSX C USB FIP au port USB. Si vous utilisez un terminal de dialogue opérateur Magelis, le pilote est automatiquement téléchargé.
• Ne branchez pas l'adaptateur de communication TSX C USB FIP lorsque le pilote n'est pas installé.
AVERTISSEMENTRISQUE D'EXPLOSION
N'utilisez pas l'unité dans un environnement dans lequel des gaz inflammables sont présents, car cela risquerait de provoquer une explosion.
Le non-respect de cette instruction peut entraîner la mort, des blessures graves ou des dommages matériels.
ATTENTIONRISQUE D'EXPOSITION AUX CONDITIONS AMBIANTES
• Empêchez les liquides, du métal ou des particules électrisées de rentrer en contact avec l'unité, car ceux-ci peuvent entraîner un dysfonctionnement.
• N'utilisez pas ou ne stockez pas l'unité dans un endroit ensoleillé, trop poussiéreux ou insalubre ou exposé aux chocs ou vibrations.
Le non-respect de cette instruction peut entraîner des lésions corporelles et/ou des dommages matériels.
FRA
NC
AIS
35015331 04 35
Introduction
Adaptateur de communication TSX C USB FIP - Présentation
Merci d'avoir acheté l'adaptateur de communication TELEMECANIQUE TSX C USB FIP. Cette unité est conçue pour servir de passerelle entre une connexion USB et un réseau Fipway ou un bus de terrain Fipio. Elle peut remplacer la carte PCMCIA (TSXFPP20) ou ISA (TSXFPC10) d'un ordinateur, d'un Magelis iPC et d'un terminal de dialogue opérateur Magelis.
Contenu de l'emballage
Cet ensemble contient les éléments suivants :
• un adaptateur de communication TSX C USB FIP avec câble USB déjà connecté,• un guide d'installation,• un collier destiné à fixer le câble FIP sur l'adaptateur.
Eléments requis
Les éléments suivants sont requis afin d'utiliser l'adaptateur :
• un pilote pour pouvoir utiliser l'adaptateur avec un PC ou un iPC (pilote TSX C USB FIP, fourni sur CD-ROM - référence TLXCDDRV20M V2.5 ou ultérieure),
• un câble FIP (TSX FP CG010 ou TSX FP CG030).
Remarque : Le pilote TSX C USB FIP pour Windows 2000 et XP est inclus dans le package pilote que vous pouvez télécharger sur le site Web de Telemecanique. Sur la page http://www.telemecanique.com/fr/index.htm, cliquez sur Téléchargements -> Logiciels -> Automatisation-> Modicon Premium, puis sélectionnez Driver Pack (V2.5 ou ultérieure).
Remarque : Vijeo Designer propose automatiquement le pilote permettant d'utiliser l'adaptateur TSX C USB FIP avec un terminal de dialogue opérateur Magelis.
36 35015331 04
FRA
NC
AIS
Caractéristiques générales
Marquage CE
L'adaptateur TSX C USB FIP est un produit marqué CE et est conforme aux normes CEM.Cette unité est conforme aux directives EN55011 Classe A et EN61000-6-2.
Modèles compatibles
Les outils (hôtes) suivants sont compatibles avec l'adaptateur TSX C USB FIP :• Ordinateur personnel• Ordinateur personnel industriel (Magelis iPC et autre iPC)• Terminaux de dialogue opérateur (Magelis XBTGT/GK, sauf XBTGT1100
et XBTGT1130)
Remarque : Un hôte peut accueillir jusqu'à deux adaptateurs TSX C USB FIP au maximum.
L'adaptateur de communication TSX C USB FIP est compatible avec les éléments suivants :
Réseaux ou bus de terrain• FIPWAY• FIPIO• WorldFIP
Logiciels• Unity Pro V3.1 ou ultérieure• PL7 V4.5 SP4 ou ultérieure• OPC Factory Server (OFS) V3.32 ou ultérieure• Vijeo Designer V4.6 ou ultérieure
FRA
NC
AIS
35015331 04 37
Caractéristiques générales
Schémas externes
Le schéma suivant illustre le panneau avant de l'adaptateur TSX C USB FIP et ses dimensions.
Electricité
Environnement
Paramètre DescriptionTension nominale 5 V cc (fournie par le câble USB)
Puissance 2,25 W max. (450 mA)
Elément DescriptionTempérature ambiante de
fonctionnement 0 °C à +50 °C (+32 °F à +122 °F)
Température de stockage -40 °C à +70 °C (-40 °F à +158 °F)
Humidité ambiante HR de 10 % à 70 %(sans condensation)
Taille : 77 x 118 x 33,5 mm (3.03 x 4.65 x 1.32 in)
FIP POWER USBERR
Remarque : Le câble vers l'hôte et le réseau n’est pas représenté.
38 35015331 04
FRA
NC
AIS
Connexion des câbles
Connexion du câble FIP
Pour connecter le câble FIP :.
Remarque : Ne retirez pas la vis du support de mise à la terre. Vous risqueriez d'endommager le produit au moment où vous la remettrez en place.
3. Insérez le câble FIP avec connecteur sous le support de mise à la terre.
4. Raccordez le connecteur.
1. Retirez la vis servant à fixer le capot.
FIP POWER USBERR
2. Desserrez la vis du support de mise à la terre sans la retirer.
Câble USB
Câble FIP
Support de mise à la terre
Câble USB
Connecteur
Collier
FRA
NC
AIS
35015331 04 39
Connexion des câbles
5. Serrez la vis du support de mise à la terre.
6. Fixez le câble FIP sur l'adaptateur à l'aide du collier.7. Replacez le capot.
AY4x VEAY3,5x VE
Tournevis à tête plate
8. Serrez la vis servant à fixer le capot.
FIP POWER USBERR
40 35015331 04
FRA
NC
AIS
Modalités de montage
Modalités de montage
Le schéma suivant indique comment monter l'adaptateur de communication TSX C USB FIP sur le rail DIN :
Remarque : Le rail DIN doit être relié à la terre.
Contact de mise à la
Rail DIN relié à la terre
20 mm0.78 in.
Dénuder le câble comme indiqué
FRA
NC
AIS
35015331 04 41
Connexion
Câble FIP et câble USB
Pour pouvoir utiliser l'adaptateur avec un PC ou un iPC, vous devez obligatoirement installer et configurer le pilote sur l'hôte. Pour plus d'informations, reportez-vous à l'annexe située à la fin de ce document.Une fois le pilote installé et configuré :
●1. Connectez l'adaptateur TSX C USB FIP au réseau Fipway (ou Fipio).
●2. Connectez l'adaptateur au PC (ou iPC) à l'aide du câble USB.
.
Vers le PC, l'iPC ou
Vers le réseau FIP
le terminal de dialogue
FIP POWER USBERR
opérateur Magelis
42 35015331 04
FRA
NC
AIS
Connexion
Longueur des câbles
Le câble USB mesure 2 m (6.562 ft). Le câble FIP mesure 1 m ou 3 m.:
Référence de câble FIP Longueur
TSX FP CG010 1 m (3.281 ft)
TSX FP CG030 3 m (9.843 ft)
ATTENTIONDANGER DÉCOULANT D'UNE MANIPULATION INCORRECTE
Suivez les recommandations ci-dessous afin d'éviter d'endommager le connecteur du câble ou le port USB.• Lors de la connexion du câble de transfert de données USB au PC,
à l’iPC ou au terminal de dialogue opérateur Magelis, insérez le connecteur du câble selon un angle de 90°.
• Lors de la déconnexion du câble, faites attention à tenir le connecteur et non le câble lui-même.
Le non-respect de cette instruction peut entraîner des lésions corporelles et/ou des dommages matériels.
FRA
NC
AIS
35015331 04 43
Etat des voyants
Etat des voyants
Voyant Etat Signification
USB jaune Communication sur le câble USB.
éteint Aucune communication sur le câble USB.
POWER vert Adaptateur alimenté.
éteint Adaptateur non alimenté.
FIP jaune Communication sur le réseau FIP.
éteint Aucun accès au réseau FIP.
ERR rouge Problème de communication FIP :• vérifiez que le câble FIP est connecté ;• déconnectez, puis reconnectez l'adaptateur ;• modifiez l'adresse de la station
(configuration du pilote) ;• vérifiez le réseau FIP (adaptation de fin de
ligne, etc.).
éteint Aucune erreur sur le réseau FIP.
44 35015331 04
FRA
NC
AIS
Installation incorrecte
Branchement de l'adaptateur avant que le pilote ne soit installé
L'adaptateur de communication TSX C USB FIP ne fonctionnera pas si vous l'avez connecté au port USB d'un PC (ou iPC) avant d'installer le pilote.Procédez comme suit pour que l'adaptateur fonctionne correctement :
1. Cliquez à l'aide du bouton droit de la souris sur Poste de travail.
2. Cliquez sur Propriétés.
3. Cliquez sur l'onglet Matériel.
4. Sélectionnez Gestionnaire de périphériques.
5. Dans Contrôleurs de bus USB, cliquez à l'aide du bouton droit de la souris sur l'équipement défectueux.
6. Sélectionnez Désinstaller.
7. Une fois la désinstallation terminée, installez le pilote (voir annexe) et branchez l'adaptateur TSX C USB FIP à un port USB du PC (ou iPC).
ES
PAÑ
OL
Tabla de contenidoInstrucciones de seguridad 47
Precauciones ................................................................................................................ 48
Adaptador de comunicación TSX C USB FIP: descripción general 49
Contenido del paquete .................................................................................................. 49Elementos necesarios ................................................................................................... 49
Marca de CE 50
Modelos compatibles .................................................................................................... 50
Dibujos externos 51
Características eléctricas .............................................................................................. 51Características ambientales .......................................................................................... 51
Conexión de cable FIP 52
Método de montaje 54
Cable FIP y cable USB 55
Longitud del cable ......................................................................................................... 56
Indicadores de estado LED 11 57
Si ha conectado el adaptador antes de instalar el controlador 58
Apéndice 87
35015331 04 45
Tabla de contenidoE
SPA
ÑO
L
46 35015331 04
ES
PAÑ
OL
35015331 04 47
Seguridad
Instrucciones de seguridad
Lea atentamente estas instrucciones y observe el equipo para familiarizarse con el dispositivo antes de instalarlo, utilizarlo o realizar su mantenimiento. Los mensajes especiales que se ofrecen a continuación pueden aparecer a lo largo de la documentación o en el equipo para advertir de peligros potenciales o para ofrecer información que aclare o simplifique los distintos procedimientos.
DESCARGO DE RESPONSABILIDAD
Sólo personal cualificado puede instalar, manejar, reparar y realizar el mantenimiento de equipos eléctricos. Schneider Electric no asume las responsabilidades que pudieran derivar de la utilización de este material.
© 2008 Schneider Electric. Todos los derechos reservados.
PELIGROPELIGRO indica una situación de peligro que provocará lesiones graves o, incluso, la muerte.
ADVERTENCIAADVERTENCIA indica una posible situación de peligro que, si no se evita, puede provocar daños en el equipo, lesiones graves o, incluso, la muerte.
AVISOAVISO indica una posible situación de peligro que, si no se evita, puede provocar lesiones graves o daños en el equipo.
Éste es el símbolo de alerta de seguridad. Se utiliza para advertirde posibles peligros que provocarían lesiones personales. Sigalas instrucciones de todos los mensajes de seguridad que sigan a este símbolo para evitar posibles lesiones o, incluso, la muerte.
Cuando en una etiqueta de peligro o advertencia aparece este símbolo, indica que existe peligro eléctrico que puede causar o quecausará lesiones personales si no se siguen las instrucciones.
48 35015331 04
ES
PAÑ
OL
Seguridad
Precauciones esenciales de seguridad
Schneider Electric ha diseñado el adaptador de comunicación TSX C USB FIP para su uso exclusivo en ubicaciones que no representen ningún riesgo (UL508).
Precauciones
Siga estas instrucciones:• El adaptador USB FIP requiere 450 mA del puerto maestro. Debido al nivel de
alimentación necesario, no conecte el adaptador a un concentrador alimentado por USB.
• Instale el controlador (consulte el apéndice) en el PC o iPC antes de conectar el adaptador de comunicación TSX C USB FIP al puerto USB del PC (o iPC). Si utiliza un operador de diálogo Magelis, el controlador se descargará automáticamente.
• No conecte el adaptador de comunicación TSX C USB FIP si no está instalado el controlador.
ADVERTENCIARIESGO DE EXPLOSIÓN
No utilice esta unidad en un entorno con gases inflamables, porque su funcionamiento podría provocar una explosión.
Si no se siguen estas instrucciones, pueden producirse daños en el equipo, lesiones personales o, incluso, la muerte.
AVISORIESGO DE EXPOSICIÓN AMBIENTAL
• No permita la entrada de líquidos, metales ni partículas cargadas en esta unidad, porque pueden producir fallos de funcionamiento.
• No utilice ni almacene esta unidad de forma que quede expuesta a la luz directa del sol, en entornos excesivamente sucios ni con demasiado polvo; de lo contrario, esto puede afectar negativamente al equipo o puede producir vibraciones.
Si no se siguen estas instrucciones, pueden producirse lesiones personales o daños materiales.
ES
PAÑ
OL
35015331 04 49
Introducción
Adaptador de comunicación TSX C USB FIP: descripción general
Gracias por adquirir el adaptador de comunicación TELEMECANIQUE TSX C USB FIP. Esta unidad está diseñada para proporcionar un puente entre una conexión USB y una red Fipway o un bus de campo Fipio. Puede sustituir las tarjetas PCMCIA (TSXFPP20) o ISA (TSXFPC10) de PC, iPC Magelis y operadores de diálogo Magelis.
Contenido del paquete
El paquete contiene los siguientes elementos:
• Un adaptador de comunicación TSX C USB FIP con un cable USB preconectado• Una guía de instalación• Un elemento de unión de cable para fijar el cable FIP al adaptador
Elementos necesarios
Los siguientes elementos son necesarios para utilizar el adaptador:
• Un controlador para utilizar el adaptador con un PC o iPC (controlador TSX C USB FIP, incluido en el controlador de CD (ref.: TLXCDDRV20M V2.5 o superior)
• Un cable FIP (TSX FP CG010 o TSX FP CG030)
Nota: El controlador TSX C USB FIP para Windows 2000 y XP está incluido en el paquete de controladores que puede descargar del sitio web de Telemecanique. En www.telemecanique.com, haga clic en downloads -> Software/Firmware -> Automation -> Modicon Premium y seleccione Driver Pack (V2.5 o superior).
Nota: Vijeo Designer proporciona automáticamente el controlador necesario para utilizar el adaptador TSX C USB FIP con un operador de diálogo Magelis.
50 35015331 04
ES
PAÑ
OL
Características generales
Marca de CE
El TSX C USB FIP tiene la marca de CE y cumple la norma de CEM.Esta unidad cumple las directivas EN55011 Clase A y EN61000-6-2.
Modelos compatibles
El TSX C USB FIP es compatible con las siguientes herramientas:• Ordenador personal• Ordenador personal industrial (iPC Magelis e iPC de otros fabricantes)• Operadores de diálogo (Magelis XBTGT/GK sin XBTGT1100 ni XBTGT1130)
Nota: Un máximo de dos adaptadores TSX C USB FIP en un host.
El adaptador de comunicación TSX C USB FIP es compatible con lo siguiente:-Redes o buses de campo:
• FIPWAY• FIPIO• WorldFIP
-Software:• Unity Pro V3.1 o superior• PL7 V4.5 SP4 o superior• Servidor OPC Factory (OFS) V3.32 o superior• Vijeo Designer V4.6 o superior
ES
PAÑ
OL
35015331 04 51
Características generales
Dibujos externos
El diagrama siguiente muestra el panel delantero del TSX C USB FIP y su tamaño.
Características eléctricas
Características ambientales
Parámetro Descripción
Tensión calculada 5 V CC (suministrados por el cable USB)
Consumo de alimentación 2,25 W máx. (450 mA)
Elemento Descripción
Temperatura ambiental en servicio De 0 °C a +50 °C (de +32 °F a +122 °F)
Temperatura de almacenamiento De -40 °C a +70 °C (de -40 °F a +158 °F)
Humedad ambiental Del 10 % al 70 % de humedad relativa(sin condensación)
Tamaño: 77 x 118 x 33,5 mm (3,03 x 4,65 x 1,32 in)
FIP POWER USBERR
Nota: No se muestra el cable conectados al host y a la red.
52 35015331 04
ES
PAÑ
OL
Conexión de cable
Conexión de cable FIP
Para conectar el cable FIP, lleve a cabo lo siguiente:.
Nota: No retire el tornillo del soporte de puesta a tierra, ya que podrían producirse daños en el producto al volver a colocarlo en su lugar.
3. Inserte el cable FIP con el conector debajo del soporte de puesta a tierra.
4. Enchufe el conector.
1. Afloje el tornillo de fijación de la cubierta.
FIP POWER USBERR
2. Afloje el tornillo del soporte de puesta a tierra sin retirarlo.
Cable USB
Cable FIP
Soporte de puesta a tie
Cable USB
Conector
Elemento de unión del cable
ES
PAÑ
OL
35015331 04 53
Conexión de cable
5. Apriete el tornillo del soporte de puesta a tierra..
6. Fije el cable FIP al adaptador con el elemento de unión del cable7. Vuelva a colocar la cubierta.
AY4x VEAY3,5x VE
Destornillador de cabeza plana
8. Apriete el tornillo de fijación de la
cubierta.
FIP POWER USBERR
54 35015331 04
ES
PAÑ
OL
Método de montaje
Método de montaje
El siguiente diagrama muestra cómo se debe montar el adaptador de comunicación TSX C USB FIP en un segmento DIN.
Nota: El segmento DIN debe estar conectado eléctricamente a tierra.
Contacto de puesta a
Segmento DIN
conectado a tierra
20 mm0.78 in.
Pelar el cable tal y como se muestra
ES
PAÑ
OL
35015331 04 55
Conexión
Cable FIP y cable USB
Para utilizar el adaptador con un PC o iPC, debe instalar y configurar el controlador en el host (para obtener más información, consulte el apéndice del final de este documento).Tras instalar y configurar el controlador:
●1. Conecte el adaptador TSX C USB FIP a la red Fipway (o red Fipio)
●2. Conecte el adaptador al PC (o iPC) con el cable USB.
.
Al PC, iPC o al
A la red FIP
operador de diálogo Magelis
FIP POWER USBERR
56 35015331 04
ES
PAÑ
OL
Conexión
Longitud del cable
El cable USB tiene una longitud de 2 m (6.562 ft). El cable FIP tiene una longitud de 1 ó 3 metros.:
Referencia del cable FIP Longitud
TSX FP CG010 1 m (3.281 ft)
TSX FP CG030 3 m (9.843 ft)
AVISORIESGO DE MANIPULACIÓN INCORRECTA
Tenga en cuenta lo siguiente para evitar que se dañe el conector del cable o el puerto USB:• Al conectar el cable de transferencia de datos USB al PC, iPC o al
operador de diálogo Magelis, inserte el conector del cable en un ángulo correcto de 90°.
• Al desconectar el cable, asegúrese de sujetar el conector, no el cable.
Si no se siguen estas instrucciones, pueden producirse lesiones personales o daños materiales.
ES
PAÑ
OL
35015331 04 57
Estado de LED
Indicadores de estado LED 11
LED Estado Significado
USB Amarillo Comunicación en el cable USB.
Apagado No hay comunicación en el cable USB.
POWER Verde El adaptador está conectado a la alimentación.
Apagado El adaptador no está conectado a la alimentación.
FIP Amarillo Hay comunicación en la red FIP.
Apagado No se puede acceder a la red FIP.
ERR Rojo Problema de comunicación FIP:• Compruebe que el cable FIP esté conectado.• Desconecte y vuelva a conectar el adaptador.• Modifique la dirección de estación (configuración
del controlador).• Compruebe la red FIP (en caso de ausencia de
adaptación de fin de línea,...).
Apagado No hay error en la red FIP.
58 35015331 04
ES
PAÑ
OL
Instalación incorrecta
Si ha conectado el adaptador antes de instalar el controlador
Si ha conectado el adaptador TSX C USB FIP al puerto USB de un PC (o iPC) antes de instalar el controlador, el adaptador no funcionará. Para que el adaptador funcione normalmente, siga este procedimiento:
1. Haga clic con el botón derecho del ratón en Mi PC.
2. Haga clic en Propiedades.
3. Seleccione la ficha Hardware.
4. Seleccione Administrador de dispositivos.
5. En Controladores de bus serie universal, haga clic con el botón derecho del ratón sobre el dispositivo que presenta fallo.
6. Seleccione Desinstalar.
7. Una vez finalizada la desinstalación, instale el controlador (consulte el apéndice) y conecte el adaptador TSX C USB FIP al puerto USB del PC (o iPC).
ITA
LIA
NO
35015331 04 59
Indice
Istruzioni relative alla sicurezza 61
Precauzioni ................................................................................................................... 62
Scheda di comunicazione TSX C USB FIP - Panoramica 63
Contenuto della confezione .......................................................................................... 63Elementi necessari ........................................................................................................ 63
Marcatura CE 64
Modelli compatibili ......................................................................................................... 64
Design esterno 65
Specifiche elettriche...................................................................................................... 65Specifiche ambientali .................................................................................................... 65
Collegamento del cavo FIP 66
Procedura di montaggio 68
Cavo FIP e cavo USB 69
Lunghezza dei cavi ....................................................................................................... 70
LED di stato 71
Inserimento della scheda prima dell'installazione del driver 72
Appendice 87
60 35015331 04
ITA
LIA
NO
Indice
ITA
LIA
NO
35015331 04 61
Sicurezza
Istruzioni relative alla sicurezza
Leggere attentamente queste istruzioni e osservare l'apparecchiatura per acquisire familiarità prima di iniziare le operazioni di installazione, uso o manutenzione. I seguenti messaggi speciali possono apparire in diverse parti della documentazione oppure essere indicati sull'apparecchiatura per segnalare rischi o per richiamare l'attenzione su informazioni che chiariscono o semplificano una procedura.
DISCONOSCIMENTO DI RESPONSABILITÀLe apparecchiature elettriche devono essere installate, azionate e sottoposte a interventi di assistenza e manutenzione soltanto da parte di personale qualificato. Schneider Electric declina ogni responsabilità per qualsiasi conseguenza risultante dall'utilizzo di questo tipo di materiale.© 2008 Schneider Electric. Tutti i diritti riservati.
PERICOLOPERICOLO indica una situazione a rischio che può causare gravi lesioni personali o mortali.
AVVERTENZAAVVERTENZA indica una potenziale situazione di rischio, la quale, se non evitata, può causare gravi rischi all'incolumità personale o danni alle apparecchiature.
ATTENZIONEATTENZIONE indica una situazione potenzialmente pericolosa, la quale, se non evitata, può causare rischi di lesioni alla persona o danni alle apparecchiature.
Questo simbolo indica un segnale di pericolo. È utilizzato per segnalare potenziali rischi di lesioni alla persona. Rispettare tutti i messaggi di sicurezza indicati da questo simbolo per evitare lesioni gravi o mortali.
L'aggiunta di questo simbolo a un'etichetta di sicurezza di tipo Pericolo o Avvertenza indica la presenza di un rischio elettrico che, in caso di mancata osservanza delle istruzioni, può causare o causerà lesioni personali.
62 35015331 04
ITA
LIA
NO
Sicurezza
Precauzioni di sicurezza essenziali
La scheda di comunicazione TSX C USB FIP è stata progettata da Schneider Electric per l'impiego esclusivo in luoghi non a rischio (UL508).
Precauzioni
Rispettare le seguenti istruzioni:
• La scheda USB Fip richiede 450 mA dalla porta master. Dato il livello di alimenta-zione richiesto, non collegare la scheda a un hub alimentato dalla porta USB.
• In un PC o un iPC, installare il driver (vedere l'appendice) prima di inserire la scheda di comunicazione TSX C USB FIP nella porta USB del PC (o dell'iPC). Se si sta utilizzando una finestra di dialogo operatore Magelis, il driver verrà scaricato automaticamente.
• Non inserire la scheda di comunicazione TSX C USB FIP se non è stato installato il driver.
AVVERTENZARISCHIO DI ESPLOSIONE
Per evitare il rischio di esplosioni, non utilizzare questa unità in ambienti in cui siano presenti gas infiammabili.
La mancata osservanza di queste istruzioni può causare morte, lesioni personali gravi o danneggiamento dell'apparecchiatura.
ATTENZIONERISCHI DERIVANTI DALL'ESPOSIZIONE AMBIENTALE
• Assicurarsi che non possano penetrare nell'unità liquidi, particelle metalliche o magnetiche, in quanto potrebbero provocare il funzionamento anomalo dell'unità stessa.
• Non usare o lasciare l'unità esposta alla luce del sole diretta, né in un ambiente polveroso o sporco o laddove possa subire forti impatti o vibrazioni.
La mancata osservanza di tale precauzione può provocare lesioni alle persone o danni all'apparecchiatura.
ITA
LIA
NO
35015331 04 63
Introduzione
Scheda di comunicazione TSX C USB FIP - Panoramica
Grazie per aver acquistato la scheda di comunicazione TELEMECANIQUE TSX C USB FIP. Quest'unità è stata progettata per fornire un bridge tra un collegamento USB e una rete Fipway o un bus di campo Fipio. Può sostituire sia la scheda PCMCIA (TSXFPP20) sia la scheda ISA (TSXFPC10) di un PC, di un Magelis iPC e di una finestra di dialogo operatore Magelis.
Contenuto della confezione
Questa confezione contiene i seguenti elementi:
• Una scheda di comunicazione TSX C USB FIP con cavo USB preparato• Una Guida d'installazione• Una fascetta di fissaggio del cavo FIP alla scheda
Elementi necessari
Per utilizzare la scheda sono richiesti i seguenti elementi:
• Un driver per utilizzare la scheda con un PC o con l'iPC (driver TSX C USB FIP, incluso nel CD driver (rif: TLXCDDRV20M V2.5 o successiva)).
• Un cavo FIP (TSX FP CG010 o TSX FP CG030)
Nota: il driver TSX C USB FIP per Windows 2000 e XP è incluso nel driver pack scaricabile dal sito Web di Telemecanique. Nel sito web www.telemecanique.com, fare clic su Downloads -> Software/Firmware -> Automation -> Modicon Premium, quindi selezionare Driver Pack (V2.5 o successiva).
Nota: Vijeo Designer fornisce automaticamente il driver per utilizzare la scheda TSX C USB FIP con una finestra di dialogo operatore Magelis.
64 35015331 04
ITA
LIA
NO
Specifiche generali
Marcatura CE
La scheda TSX C USB FIP dispone del marchio CE e rispetta le norme relative alla compatibilità elettromagnetica (EMC).Questa unità è conforme alle norme EN55011 classe A e alle direttive EN61000-6-2.
Modelli compatibili
I seguenti strumenti (host) sono compatibili con la scheda TSX C USB FIP:• Personal Computer• industrial Personal Computer (Magelis iPC e altri iPC)• Finestre di dialogo operatore (Magelis XBTGT/GK senza XBTGT1100 e
XBTGT1130)
Nota: al massimo due schede TSX C USB FIP su un host.
La scheda di comunicazione TSX C USB FIP è compatibile con i seguenti elementi:-reti o bus di campo:
• FIPWAY• FIPIO• WorldFIP
-software:• Unity Pro V3.1 o successiva• PL7 V4.5 SP4 o successiva• OPC Factory Server (OFS) V3.32 o successiva• Vijeo Designer V4.6 o successiva
ITA
LIA
NO
35015331 04 65
Specifiche generali
Design esterno
Nell'illustrazione che segue è raffigurata la parte frontale della scheda TSX C USB FIP e le relative dimensioni.
Specifiche elettriche
Specifiche ambientali
Parametro Descrizione
Tensione nominale 5 V DC (fornita dal cavo di USB)
Assorbimento 2,25 W max (450mA)
Elemento Descrizione
Temperatura ambiente d'esercizio Da 0 °C a +50 °C (da +32 °F a +122 °F)
Temperatura di immagazzinamento Da -40 °C a +70 °C (da -40 °F a +158 °F)
Umidità ambientale Da 10% RH a 70% RH(senza condensa)
Dimensioni: 77 x 118 x 33,5 mm (3.03 x 4.65 x 1.32 in)
FIP POWER USBERR
Nota: i cavi di collegamento con l'host e la rete non sono illustrati.
66 35015331 04
ITA
LIA
NO
Connessione cavo
Collegamento del cavo FIP
Per collegare il cavo FIP:.
Nota: non rimuovere la vite della staffetta di messa a terra, poiché si potrebbe danneggiare il prodotto quando la si reinserisce.
3. Inserire il cavo FIP con il connettore sotto la staffetta di messa a terra.
4. Inserire il connettore.
1. Svitare le viti di fissaggio del
coperchio.
FIP POWER USBERR
2. Allentare, ma non rimuovere, la vite
della staffetta di messa a terra.
Cavo USB
Cavo FIP
Staffetta di messa a terra
Cavo USB
Connettore
Fascetta per il fissaggio del cavo
ITA
LIA
NO
35015331 04 67
Connessione del cavo
5. Serrare la vite della staffetta di messa a terra..
6. Fissare il cavo FIP al connettore utilizzando l'apposita fascetta7. Reinstallare il coperchietto.
AY4x VEAY3,5x VE
Cacciavite a testa piatta
8. Avvitare la vite di fissaggio del
coperchio.
FIP POWER USBERR
68 35015331 04
ITA
LIA
NO
Procedura di montaggio
Procedura di montaggio
La seguente figura mostra come montare la scheda di comunicazione TSX C USB FIP sulla guida DIN.
Nota: la guida DIN deve essere collegata elettricamente a terra.
Contatto di messa a terra
Guida DIN collegata a terra
20 mm0.78 in.
cavo a nastro, come mostrato
ITA
LIA
NO
35015331 04 69
Connessione
Cavo FIP e cavo USB
Per poter utilizzare la scheda con un PC o un iPC, è obbligatorio installare e configurare il driver sull'host (per maggiori informazioni, fare riferimento all'appendice contenuta alla fine di questo documento)Dopo aver installato e configurato il driver:
●1. Collegare la scheda TSX C USB FIP alla rete Fipway (o alla rete Fipio)
●2. Collegare la scheda al PC (o all'iPC) con il cavo USB
.
Al PC, all'iPC o alla
Alla rete FIP
finestra di dialogo
FIP POWER USBERR
operatore Magelis
70 35015331 04
ITA
LIA
NO
Connessione
Lunghezza dei cavi
Il cavo USB è lungo 2 m (6.562 ft). Il cavo FIP è lungo 1 o 3 metri:
Codice di riferimento del cavo FIP Lunghezza
TSX FP CG010 1 m (3.281 ft)
TSX FP CG030 3 m (9.843 ft)
ATTENZIONERISCHIO DI MANIPOLAZIONE IMPROPRIA
Per evitare danni al connettore del cavo o alla porta USB, attenersi alle istruzioni riportate di seguito.• Quando si collega il cavo di trasferimento dati USB al PC, all'industrial
PC o alla finestra di dialogo operatore Magelis, inserire il connettore del cavo con un angolo di 90°.
• Quando si scollega il cavo, afferrare il connettore e non il cavo stesso.
La mancata osservanza di tale precauzione può provocare lesioni alle persone o danni all'apparecchiatura.
ITA
LIA
NO
35015331 04 71
Stato dei LED
LED di stato
LED Stato Significato
USB giallo Comunicazione sul cavo USB.
spento Nessuna comunicazione sul cavo USB.
POWER verde La scheda è alimentata.
spento La scheda non riceve l'alimentazione.
FIP giallo Attività di comunicazione sulla rete FIP.
spento Nessun accesso alla rete FIP.
ERR rosso Problema di comunicazione FIP:• verificare che il cavo FIP sia collegato• disinserire e reinserire la scheda• modificare l'indirizzo della stazione (configurazione
del driver)• verificare la rete FIP ( adattatore di estremità
linea, ecc.).
spento Nessun errore sulla rete FIP.
72 35015331 04
ITA
LIA
NO
Installazione errata
Inserimento della scheda prima dell'installazione del driver
Se è stata inserita la scheda di comunicazione TSX C USB FIP nella porta USB di un PC (o un iPC) prima di installare il driver, la scheda non funzionerà. Per ripristinare il corretto funzionamento della scheda, procedere come segue:
1. Fare clic con il pulsante destro su Risorse del computer
2. Fare clic su Proprietà
3. Selezionare la scheda Hardware
4. Selezionare Gestione periferiche
5. In Controller USB (Universal Serial Bus), fare clic con il pulsante destro sul dispositivo non funzionante
6. Selezionare Disinstallazione
7. Una volta terminata la disinstallazione, installare il driver (vedere l'appendice) e inserire la scheda TSX C USB FIP nella porta USB di un PC (o un iPC).
简体
中文
35015331 04 73
安全
安全使用说明 75
注意事项 ........................................................................................................................ 76
TSX C USB FIP 通讯适配器 - 概述 77
装箱物品 ........................................................................................................................ 77所需物品 ........................................................................................................................ 77
CE 标记 78
兼容型号 ........................................................................................................................ 78
外部图解 79
电气 ...............................................................................................................................79环境 ...............................................................................................................................79
FIP 电缆连接 80
安装方法 82
FIP 电缆和 USB 电缆 83
电缆长度 ........................................................................................................................ 84
LED 状态指示灯 85
在安装驱动程序之前连接适配器 86
附录 87
74 35015331 04
简体
中文
安全
简体
中文
35015331 04 75
安全
安全使用说明
在安装、操作或维护本设备之前,请仔细阅读这些说明,并观察和熟悉本设备。在整篇文档中或在设备上可能会出现下列特殊信息,以告诫潜在的危险或提请您注意那些阐明或简化某过程的信息。
免责声明
只有具备相应资质的人员才能安装、操作、维修和保养电气设备。 Schneider Electric 对于使用本资料而引发的任何后果概不负责。
© 2008 Schneider Electric. 保留所有权利。
危险“危险”符号用于指明易造成人员严重伤亡的危险场所。
警告“警告”符号用于指明存在安全隐患的场所,如果不加以规避,则会损坏设备,甚至造成人员严重伤亡。
小心“小心”符号用于指明存在安全隐患的场所,如果不加以规避,则会导致人身伤害或设备受损。
这是一种安全提示符号,用于提醒使用者存在造成人身伤害的安全隐患。务必遵循此符号附注的所有安全须知进行操作,以免造成人员伤亡。
“危险”或 “警告”安全标签上的这种符号表示存在电击危险,如果使用者不遵照使用说明进行操作,则可能或将造成人身伤害。
76 35015331 04
简体
中文
安全
重要安全注意事项
Schneider Electric 已设计了 TSX C USB FIP 通讯适配器,但仅用于非危险环境中 (UL508)。
注意事项
请按以下说明操作:
• USB Fip 适配器需要由主站端口提供 450 mA 的电流。由于所需的电源电平,请勿
将此适配器连接到由 USB 供电的集线器。
• 在 PC 或 iPC 上,安装驱动程序(请参阅附录),然后在 PC (或 iPC)的 USB 端口上插入 TSX C USB FIP 通讯适配器。如果您使用了 Magelis 对话操作员终
端,则将自动下载驱动程序。• 如果未安装驱动程序,请勿插入 TSX C USB FIP 通讯适配器。
警告存在爆炸的危险
请勿在存在易燃性气体的环境中使用此单元。在此类环境中操作此单元可能会引起爆炸。
若违背本说明,则会损坏设备,导致严重的人身伤害,甚至死亡。
小心环境暴露危险
• 避免让液体、金属或带电粒子进入此单元内部,否则可能导致功能失常。
• 请勿在阳光直射、灰尘过多或太脏的环境中或者在可能发生强烈冲击或振
动的地方使用或储存此单元。
若违背本说明,则可能造成人身伤害或导致设备损坏。
简体
中文
35015331 04 77
简介
TSX C USB FIP 通讯适配器 - 概述
感谢您购买 TELEMECANIQUE TSX C USB FIP 通讯适配器。此单元的作用是在 USB 连接与 Fipway 网络或 Fipio 现场总线之间提供桥接。它可以同时取代 PC、 Magelis iPC 和 Magelis 对话操作员终端上的 PCMCIA 卡 (TSXFPP20) 或 ISA 卡 (TSXFPC10)。
装箱物品
包装箱内包含以下物品:
• 一个 TSX C USB FIP 通讯适配器,配备了预连接的 USB 电缆
• 一份安装指南• 一个电缆卡箍,用于将 FIP 电缆固定到适配器上
所需物品
要使用此适配器,要求具备以下物品:
• 使适配器可用于 PC 或 iPC 的驱动程序(TSX C USB FIP 驱动程序,包括在 CD 驱动程序中(参考号:TLXCDDRV20M V2.5 或更高版本))。
• 一根 FIP 电缆(TSX FP CG010 或 TSX FP CG030)
注: 适用于 Windows 2000 和 XP 的 TSX C USB FIP 驱动程序包括在驱动程序包中,您可以从 telemecanique 网站下载此驱动程序包。在 www.telemecanique.com 上,单击下载 -> 软件 / 固件 -> 自动化 -> Modicon Premium,然后选择驱动程序包(V2.5 或更高版本)。
注: Vijeo Designer 自动提供使 TSX C USB FIP 适配器可用于 Magelis 对话操作员终端的驱动程序。
78 35015331 04
简体
中文
一般规格
CE 标记
TSX C USB FIP 具有 CE 标记并符合 EMC 标准。此单元符合 EN55011 A 类及 EN61000-6-2 规程。
兼容型号
以下工具(主机)与 TSX C USB FIP 兼容:• 个人计算机• 工业个人计算机(Magelis iPC 和其他 iPC)
• 对话操作员终端(Magelis XBTGT/GK,不含 XBTGT1100 和 XBTGT1130)
注: 一台主机上最多可以使用两个 TSX C USB FIP 适配器。
TSX C USB FIP 通讯适配器与以下各项兼容:- 网络或现场总线:
• FIPWAY• FIPIO• WorldFIP
- 软件:• Unity Pro V3.1 或更高版本
• PL7 V4.5 SP4 或更高版本
• OPC Factory Server (OFS) V3.32 或更高版本
• Vijeo Designer V4.6 或更高版本
简体
中文
35015331 04 79
一般规格
外部图解
下图描述了 TSX C USB FIP 的前面板及其尺寸。
电气
环境
参数 描述
额定电压 5 V DC (由 USB 电缆供电)
功耗 2.25 W 最大值 (450mA)
项 描述
操作环境温度 0 °C 至 +50 °C (+32 °C 至 +122 °C)
储存温度 -40 °C 至 +70 °C (-40 °C 至 +158 °C)
环境湿度 10% RH 至 70% RH (无冷凝)
尺寸:77 x 118 x 33.5 毫米
(3.03 x 4.65 x 1.32 英寸)FIP POWER USBERR
注: 未显示用于连接到主机和网络的电缆。
80 35015331 04
简体
中文
电缆连接
FIP 电缆连接
要连接 FIP 电缆,请执行以下操作:.
注: 请勿卸下接地托架螺钉,否则,当将其装回原位时可能损坏产品。
3. 将带有连接器的 FIP 电缆插入到接地托架下方。
4. 连接此连接器。
1. 拧下护盖固定螺钉。
FIP POWER USBERR
2. 拧松(但不要卸下)接地托架螺钉。
USB 电缆
FIP 电缆
接地托架
USB 电缆
连接器
电缆卡箍
简体
中文
35015331 04 81
电缆连接
5. 拧紧接地托架螺钉。
6. 使用电缆接头将 FIP 电缆连接到适配器上。
7. 将护盖安装到位。
AY4x VEAY3.5x VE
平头螺丝刀
8. 拧入护盖固定螺钉。
FIP POWER USBERR
82 35015331 04
简体
中文
安装方法
安装方法
下图显示如何在 DIN 滑轨上安装 TSX C USB FIP 通讯适配器。
注: DIN 滑轨必须通过电路连接到接地
接地触点
连接到接地的 DIN
20 mm0.78 in.
剥开电缆(如图)
简体
中文
35015331 04 83
连接
FIP 电缆和 USB 电缆
为了使此适配器可用于 PC 或 iPC,必须在主机上安装和配置驱动程序(有关详细信息,请参阅本文档末尾的附录)安装和配置驱动程序后,请执行以下操作:
●1. 将 TSX C USB FIP 适配器连接到 Fipway 网络(或 Fipio 网络)
●2. 使用 USB 电缆将适配器连接到 PC (或 iPC)
.
至 PC、iPC 或
至 FIP 网络
Magelis 对话操作员终端
FIP POWER USBERR
84 35015331 04
简体
中文
连接
电缆长度
USB 电缆长度为 2 米(6.562 英尺)。 FIP 电缆长度为 1 米或 3 米 :
FIP 电缆参考号 长度
TSX FP CG010 1 米(3.281 英尺)
TSX FP CG030 3 米(9.843 英尺)
小心操作不当危险
为防止损坏电缆连接器或 USB 端口,请注意以下事项:
• 当将 USB 数据传输线连接到 PC、工业 PC 或 Magelis 对话操作员终端
时,请确保以 90° 角的正确方向插入电缆连接器。
• 断开电缆连接时,请捏住连接器部分而不是电缆本身。
若违背本说明,则可能造成人身伤害或导致设备损坏。
简体
中文
35015331 04 85
LED 状态
LED 状态指示灯
LED 状态 含义
USB 黄色 USB 电缆上存在通讯。
灭 USB 电缆上不存在通讯。
POWER 绿色 已向适配器供电。
灭 尚未向适配器供电。
FIP 黄色 FIP 网络上存在通讯活动。
灭 未访问 FIP 网络。
ERR 红色 FIP 通讯问题:• 验证是否已连接 FIP 电缆,
• 断开连接,然后重新连接适配器,
• 修改工作站地址(驱动程序配置),
• 验证 FIP 网络(线端适配等)。
灭 FIP 网络上没有错误。
86 35015331 04
简体
中文
错误安装
在安装驱动程序之前连接适配器
如果您在安装驱动程序之前在 PC (或 iPC)的 USB 端口上连接 TSX C USB FIP 通讯适配器,则此适配器将不会正常工作。 请遵循以下过程,以使适配器正常工作:
1. 右键单击我的电脑
2. 然后单击属性
3. 选择硬件选项卡
4. 选择设备管理器
5. 在通用串行总线控制器中,右键单击此故障设备
6. 选择卸载
7. 卸载完成后,安装此驱动程序(请参阅附录),并将 TSX C USB FIP 适配器插入到 PC (或 iPC)的 USB 端口。
APP
END
IX
35015331 04 87
Presentation
Presentation
This appendix describes how to install the TSX C USB FIP driver on a PC or a Magelis iPC. This driver will configure the TSX C USB FIP adapter, then the driver will manage the communication between the Windows application softwares and the equipment on Fip network or field bus.This driver is compatible with Windows 2000 and XP.
Note : The TSX C USB FIP driver for windows 2000 and XP is included in the driver pack that you can download from the telemecanique web site. On www.telemecanique.com, click downloads -> Software/Firmware -> Automation -> Modicon Premium and select Driver Pack (V2.5 or higher).
88 35015331 04
APP
END
IXInstallation
Installing the Driver
The driver installation is a standard installation, executed from the drivers CD-Rom.
Checking the Driver Settings
Before installing the driver, you should make sure the operating system on the PC or iPC allows unsigned driver to be installed.To do this.:
Step Action
1 Select the My computer icon, right-click, and click Properties
2 In System Properties, select the Hardware tab.
3 Click the Driver Signing button.The following window appears:
4 Select Warn - Prompt and click OK.
APP
END
IX
35015331 04 89
Installation
Installing the Driver
To install the driver:
Start of installation
Double click SETUP.EXE
Click Next
Configure the driver then close the configuration screen
(see the next chapter)
End of installation
Restart the computer
Choose Run this program from its current location then confirm
by clicking OK
On the root of the CD drive, click on the file _installdrivers.htm
Choose Yes in the security warning screen
To launch the installation use one of
the following option
Access the directory of the driver FIP-CUSBFIP\Win2000\DISK1
Insert CD-ROM in CD-ROM drive
Connect the adapter
Select the linkFip-CUSBFIPAdapter
90 35015331 04
APP
END
IXInstallation
Configuring the Driver
With the driver configuration tool, you can configure the driver in Fipway mode or Fipio mode.The driver configuration tool is shown below.
Note : Once installed the driver can be reconfigured, for that, click Start -> Control Panel -> Drivers Manager and choose the USB-FIP Driver tab.
Label Meaning
1 Network address (between 0 and 127).
2 Station address (between 0 and 63).
3 Network Type (FIPWAY or FIPIO).
1
2
3
APP
END
IX
35015331 04 91
Installation
Final configuration
To complete the configuration:
Step Action
1 Connect the TSX C USB FIP communication adapter to the USB of the PC (or iPC).Result:The system detects automatically the USB device, and displays the dialog boxes to configure the driver in the Operating System.
2 Select No, not this time and click Next >.
Note : In this example, the operating system is XP SP2.
92 35015331 04
APP
END
IXInstallation
3 Select Install the software automatically (Recommended)..
4 Click Next >
Step Action
APP
END
IX
35015331 04 93
Installation
The TSX C USB FIP communication adapter is now ready to use.
5 Click Continue Anyway.
6 Click on Finish.
Step Action