Tsunami MP.11 Family June 2005. Slide 2 The Tsunami MP.11 Multipoint System consists of >Central...

Tsunami MP.11 Family

June 2005

The Tsunami MP.11 Multipoint System consists of

> Central units called Base Station Unit (BSU)

> Satellites (remotes) called Subscriber Units (SU)

Units operate in one of the following bands:

> 5 GHz frequencies (5.25 to 5.85GHz depending upon local regulations)

> 2.4 GHz ISM band.

> Each band offers several alternative channels

Technology: TDD

> The system uses a proprietary protocol called WORP (Wireless Outdoor Router Protocol) between BSU and SUs

General Description and Topologies

Topologies: Point to Point

Point to Point links can be created by connecting one BSU and one SU

> SU to SU direct communication is NOT possible

> BSU to BSU direct communication is NOT possible

> However…a BSU can be configured in Satellite mode (via software). In this case, it will behave exactly as any SU

Topologies: Point to Multipoint

Point to Multipoint networks can be created by having more than one SU connecting (“registering”) to the same BSU

There is an absolute maximum of remotes that a Base can handle (more details in next slides)

> Administrator can limit the number of remotes via software to a smaller value by configuring the parameter Maximum Number of Remotes in the BSU

> The BSU stops polling for new registrations when the“current Number of Remotes” = “Maximum Number of Remotes”

Tsunami MP.11 Models

Four Multipoint Models

Three MP.11 QuickBridge (PtP) Models:

ModelFrequency

[GHz]

Max. Data Rate

[Mbps]Housing

2411 2.4 11 Indoor

5054 5 36 Indoor

5054 R 5 36 Rugged

2454 R 2.4 36 Rugged

ModelFrequency

[Ghz]

Max. Data Rate

[Mbps]Housing

QB 2411 2.4 11 Indoor

QB 5054 R 5 54 Rugged

QB 2454 R 2.4 54 Rugged

Model 2411 (non rugged)

2411-BSU

> Base Station Unit operating in 2.4 GHz band

> Supports up to 100 satellites

2411-SU

> Subscriber Unit operating in 2.4 GHz band

2411-RSU

> Residential Subscriber Unit operating in 2.4 GHz band

> Similar to SU but comes with 15dBi window antenna w/2 meter cable and N male connector. Net Gain is about 12dBi.

> Supports only 8 devices on the Ethernet side (8 MAC Addresses)

Model 5054 (non rugged)

5054-BSU

> Base Station Unit operating in 5 GHz band

> No antenna is included

> Supports up to 250 satellites

5054-SU

> Subscriber Unit operating in 5 GHz band

> No antenna included

5054-RSU

> Residential Subscriber Unit operating in 5 GHz band

> Similar to SU but delivered with 15 dBi window antenna.Net Gain about 13dBi.

> Supports limited number of devices on the Ethernet side (8 MAC addresses)

Difference between SU and RSU

There are two functional differences between an SU and RSU

> MAC Address Capacity: The SU can handle “unlimited” MAC addresses on the Ethernet side

(900) The RSU can handle a maximum of 8 MAC Addresses

> PoE Capability: The SU has PoE capabilities, The RSU does not have PoE capabilities

Model 5054-R (rugged)

5054-BSUR

> Base Station Unit operating in 5 GHz band

> No antenna is included

> Supports up to 250 remotes

5054-SUA

> Subscriber Unit operating in 5 GHz band with antenna connector (no antenna is included)

5054-SUR

> Subscriber Unit operating in 5 GHz band with integrated antenna (23 dBi)

The 5054-R products are compatible with the 5054 products

Model 2454-R (rugged)

2454-BSUR

> Base Station Unit operating in 2.4 GHz band

> Supports up to 250 remotes


2454-SUA

> Subscriber Unit operating in 2.4 GHz band with antenna connector


2454-SUR

> Subscriber Unit operating in 2.4 GHz band with integrated panel antenna (17 dBi)

The 2454-R products are NOT compatible with the 2411 products

Quickbridge.11 2411

Ready-to-run point-to-point link based on Model 2411 equipment

> Operates in 2.4 Ghz

> Data Rate up to 11Mbps

> Packaging includes: 2411 BSU (1) 2411 SU (1) Yagi 14 dBi (2) LMR-400 50ft (2) Surge Arrestors (2) Software and manuals

Quickbridge.11 5054 R

Ready-to-run point-to-point link based on Model 5054 R equipment

> Operates in 5Ghz band


> Includes: 5054 R BSU (1) and SU (1) both with integrated 23-dBi antennas 50 m (164 ft) outdoor, terminated CAT5 cables (2) PoE adapters (2) Mounting hardware Software and manual No surge arrestors are included

(offered separately)

Quickbridge.11 2454 R

Ready-to-run point-to-point link based on Model 2454 R equipment

> Operates in 2.4Ghz band


> Includes: BSU (1) and SU (1) both with integrated 17dBi antennas, 50 m (164 ft) outdoor, terminated CAT5 cables (2) PoE adapters (2) Mounting hardware software and manuals No surge arrestors are included

MP.11 Quickbridge limitations

All MP.11 QB units come protected with License Key to “stay” QB after Factory Default reset:

> The QB SU can be used as regular (a “non QB”) SU.In other words, a QB SU can become part of an MP.11 Multipoint System.

> The QB BSU can be put in Satellite mode and used as regular SU.

> The QB BSU cannot be used as non-QB BSU (i.e. the parameter Maximum Number of Remotes is hard coded to “1” and can not be changed).

Product Variants and How to Order

There are several product variants to accommodate for the different RF regulations and/or electrical specs. of different countries/regions.

When selecting an MP.11 product, you must choose:

> A) Model: 2411, 5054, 5054 R, 2454 R

> B) Product: BSU, SU, SUA, RSU

> C) Variant: UK, EU, etc

> Eg.: 5054 –BSUR -EU 5054 – SUR – UK 5054 – SUA – AU

For a full list of MP.11 Products and Accessories -> MP.11 Family

System/Software Features Overview

System Features (thru release 2.2.5)

Works with Scantool

IP Addressable

> Static or dynamically assigned using DHCP-Client

Management through

> Web Interface

> Command Line Interface (CLI)

> Simple Network Management Protocol (SNMP) Support for standard MIB Product specific parameters/tallies in Proxim provided MIB

System Features (cont.)

WORP protocol optimizes media (channel access) control in outdoor installations over longer distances

> Adaptive polling protocol

> No low level (IEEE 802.11) ACKs

> Super frames

> Asymmetric Bandwidth Management SU negotiates configured bandwidth settings with BSU

> No Sleep Mode Configuration option to change the adaptive polling method in WORP

> More details on WORP -> Click here or here

SU Roaming

> Allows SUs to ‘roam’ from BSU to BSU, allowing mobility and/or redundancy

> Provides ‘seamless’ roaming to many applications (no guarantee of session persistence)


Dynamic Frequency Selection

> ETSI domain countries do not allow you to select the channel BSU Radar Detection SU scans all frequencies to find optimal BSU

10 and 5 MHz radio channel-width (rugged units only)

> 5 and 10 MHz channels in addition to the 20 MHz standard

> Wider channel allows higher data-rate, but occupies more spectrum and allows less channels in the available band

> Narrower channel occupies less spectrum, gets more distance and allows for more channels in the band, but lowers the data-rate per channel Half the channel-width means half the data-rate Allows for better capacity planning through channel separation Roaming is only possible between BSUs with the same-bandwidth

channel configurations


Transmit Power Control

> Adjust the output power of the unit to a lower level in order to reduce interference to neighboring devices

> Allows use of higher gain antennas while staying within the EIRP limits applicable in the operational domain

Satellite Density

> Influences the receive sensitivity of the radio interface

> Reducing the sensitivity of the radio enables unwanted “noise” to be filtered out. (It disappears under the threshold.)

> The Satellite Density Control feature acts essentially like a “squelch” used in CB radios.


Encryption

> WEP, AES-CCM and –OCB encryption

Dynamic Data Rate Selection (DDRS)

> Automatically and dynamically adjusts transmit data rate to an ‘optimal’ value according to the current system conditions at each end of the link independently

TURBO mode support

> Uses channel bonding (not allowed in Europe)


Antenna Alignment support

> Assists in antenna alignment

> For rugged units audible antenna alignment is available.

Station Statistics

> List of SU MAC Addresses at BSU and BSU’s MAC Address at SU

> Current Transmit Rate at Local and Remote Site, Signal and noise at Local and Remote Site

> Screen (GUI) auto-refreshes every 4 seconds

Temperature Logging (rugged units only)

Event Log facility (downloadable)


Routing and bridging capability:

> RIP

> STP

DHCP Server

> Provides allocation of IP addresses to hosts behind the Ethernet side of BSU/SU/RSU

DHCP Relay agent

Network Address Translation (NAT)

> Provides bi-directional Public-to-Private IP address translation for network devices connected behind an SU/RSU


SU 1Trunk Mode

Company AVLAN 4

Company BVLAN 7

SU 2Access Mode

BSUTrunk Mode

Company AVLAN 4

Different VLAN modes supported> BSU in Trunk mode> SU 1 in Trunk mode> SU 2 in Access mode


Intra-Cell Blocking (ICB)

> Feature is provided to allow “blocking” of traffic between SUs that are connected to the same BSU

MAC Authentication

RADIUS Authentication

IP Access Table

Ethernet Protocol Filtering

Static MAC pair Filtering

Broadcast Protocol Filtering


Monitoring

> WORP statistics

> ICMP messages

> RADIUS messages

> Link Test

> Interfaces

> IP ARP Table

> IP Routes

> Learn Table

Feature/hardware dependencies

All current Tsunami MP11 hardware will accept the latest available software releases

However, not all features will be available for all models

Management interfaces will allow configuration of only the options that are available for the detected hardware

Summary of Features vs Models

Feature 2454 R 5054 R 5054 2411

# of Remotes per BSU 250 250 250 100

Max Data Rate 36Mbps 36Mbps 36Mbps 11Mbps

AES CCM X X

5 and 10 MHz Channel Bandwidth X X

Audio Antenna Alignment X X

Logging-Reporting of Internal Unit Temperature and Temperature Log Upload X X

Remote Reload support X X

Factory Default button on Power Injector X X

AES OCB X X X X

WORP “No Sleep” mode X X X X

Enhanced TPC X X X

Event Log Upload X X X X

Satellite Density Control X X X X

VLAN X X X

Upgrade Bootloader Support X X X X

Tsunami MP.11 Non RuggedTechnical Specifications

April 2005

Models 2411/5054 Characteristics

Physical Interfaces:

> One wired 10/100 Mbps port (RJ45 connector) with PoE capabilities The RSU does not have PoE

> One wireless interface with pigtail permanently attached (N male connector)

> One serial port (DB9 connector) for configuration

Digital Signature check

> to verify product Variant and activate the corresponding set of features

License file verification

> to verify BSU, SU or RSU identity of the unit

Uses top 3 LEDs

> 1st = System/Power LED> 2nd = Ethernet LED> 3rd = WORP connection indicator> 4th = NOT USED

2411/5054 Physical Specifications

Model 5054 Channels

Model 2411 Channels

Data Rates

For Model 5054

For Model 2411:

> 11Mbps/5.5/2/1 Mbps

Radio Tx power @ St-N connector Channels 36 Mbps 6-24 Mbps

5.25-5.35 GHz 52,56 and 60 17.5dBm 18.5dBm

5.25-5.35 GHz 64 12.5dBm 12.5dBm

5.47-5.725 GHz100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140

17.5dBm 18.5dBm

5.725-5.850 GHz 149, 153, 157, 161 17.5dBm 17.5dBm

5.725-5.850 GHz 165 (not FCC) 17.5dBm 17.5dBm

5054 Output Power

Normal mode Receiver Sensitivity

36 Mbps - 77 dBm

24 Mbps - 81 dBm

18 Mbps - 84 dBm

12 Mbps - 86 dBm

9 Mbps - 87 dBm

6 Mbps - 88 dBm

5054 Receiver Sensitivity

2411 Output Power and Sensitivity

Output Power is the same for all Channels and Speeds

> Standard Unit has 15dBm Output Power

> LP (Low Power unit) has 8dBm Output Power

Receiver Sensitivity

> -82 dBm @ 11Mbps

> -87 dBm @ 5.5 Mbps

> -91 dBm @ 2 Mbps

> -94 dBm @ 1 Mbps

Active Ethernet (PoE) on 2411/5054

Active Ethernet (aka Power over Ethernet – PoE) is the capacity some hardware has to be “fed” via the Ethernet port

> IEEE 802.3af is the Active Ethernet standard

> To use AE you must have an Active Ethernet Hub or an AE Power Injector AE Hubs are not repeaters, they do not amplify the data signal Total cable length between AE Hub and MP.11 must be less than 100

mts. (aprox. 325 feet)

In the 2411/5054 BSU/SU the active Ethernet integrated module receives –48 VDC over standard Cat5 cable, unused pairs

Maximum Power supplied to Models 2411/5054 is 11 watts. Units typically draw less than 7.5 watts.

The RSU does not support PoE

Other Physical Characteristics

All units have a Kensington Slot

Mounting options:

> Desktop

> Ceiling

> Wall

Kensington Slot

Specifications

For full Specifications and Accessories go to:

> Models 2411 and 5054

> Accessories

Note: the links above will only work if you have Internet connection and if you are running SlideShow mode.Pressing “Back” button in your IE will bring you back to this presentation

http://www.proxim.com/products/bwa/multipoint/mp11/mp11a/mp11_techspecs.html

http://www.proxim.com/products/bwa/accessories/

Tsunami MP.11 Rugged HardwareTechnical Specifications

April 2005

Tsunami MP.11 Rugged

Pre-WiMax product line for point-to-point and point-to-multipoint operation

> Based on non-rugged Tsunami MP.11a product architecture

> Housed in weatherproof rugged housing (IP66 rated)

> Complemented with Peltier element for temperature control Ambient Temp range –33 to +60 deg C Internal MP.11 Temp range 0 to +55 deg C

Includes audible antenna alignment option

Same code base as other Tsunami MP.11 systems

Powered via special PoE injector

> Includes Reset/Reload switch

OFDM Modulation

> works in Near-Line of Sight conditions

5054 R/2454 R Kit contents

One 5054R or 2454 R radio system in rugged weatherproof enclosure

Mounting hardware to attach to radio for mounting

Hardware for pole mounting

Hardware for wall mounting

One RJ11 to DB9 connector for serial connection (dongle)

Cable termination material

Installation CD > Software Installation Package > Documentation > ScanTool > FTP Server

Power Brick and cord

Channels

2454-R 20MHz has 3(FCC) or 4(ETSI), 10MHz has 6(FCC) or 7(ETSI) non-overlapping channels

Specifications

For full Specifications and Accessories go to:

> Models 5054 R and 2454 R (or go to Proxim Knowledge Base Answer ID 1927 and 1928)

> Accessories

Note: the links above will only work if you have Internet connection and if you are running SlideShow mode.Pressing “Back” button in your IE will bring you back to this presentation

Tsunami MP.11 Family June 2005. Slide 2 The Tsunami MP.11 Multipoint System consists of >Central...

Documents

Transcript of Tsunami MP.11 Family June 2005. Slide 2 The Tsunami MP.11 Multipoint System consists of >Central...