TSP 400 Installation Manual - … · 2013-10-16 · Installation Manual fastener (E.U. only)...
Transcript of TSP 400 Installation Manual - … · 2013-10-16 · Installation Manual fastener (E.U. only)...
THERMAL PRINTER
TSP400
INSTALLATION MANUALGUIDE D’INSTALLATIONAUFSTELLANLEITUNG
MANUALE DI INSTALLAZIONE
TABLE OF CONTENTS1. UNPACKING AND INSPECTION...................................................... 1
1-1. Unpacking .................................................................................... 11-2. Handling Notes ............................................................................ 1
2. PARTS IDENTIFICATION AND NOMENCLATURE ...................... 2
3. FERRITE CORE INSTALLATION *EUROPE ONLY ..................................3Installation of the interface cable ferrite core ...................................... 4Installation of the peripheral unit cable ferrite core ............................ 4
4. CONNECTING THE INTERFACE CABLE ....................................... 54-1. RS-232C or RS-422A Serial interface ......................................... 54-2. Centronics-type Parallel interface ............................................... 5
APPENDIX ............................................................................................. 24
– 1 –
EN
GLIS
H
1. UNPACKING AND INSPECTION1-1. Unpacking
Check each item in the box against Figure 1-1 to make sure that you haveeverything (there should be five items).If any of these items are missing, contact your supplier.
Fig. 1-1
1-2. Handling Notes
Before you start setting up your printer, make sure that you have a suitable placein which to locate it. By “a suitable place”, we mean:• Close to an easily accessible socket-outlet.• A firm, level surface which is fairly vibration-free• Away from excessive heat (such as direct sunlight, heaters, etc)• Away from excessive humidity• Away from excessive dust• With access to a steady power supply that is not subject to power surges. For
example, do not connect the printer to the same circuit as a large, noise-producing appliance such as a refrigerator or an air conditioner.
NOTE: Make sure that the line voltage is the voltage specified on the printer’sidentification plate.
Ø24mm Ø28mm
Printer
Paper-roll shaft
Sample paper roll
User’s manualInstallation Manual fastener
(E.U. only)
Ferrite core forinterface cable(E.U. only)
Ferrite corefor peripheralunit cable(E.U. only)
– 2 –
EN
GLI
SH
2. PARTS IDENTIFICATION AND NOMENCLATURETo get acquainted with the printer’s components and capabilities, refer toFigure 2-1.
Fig. 2-1
Printer coverProtects the print head andother internal components ofyour printer.
Control panelIndicates printer statusand makes control ofprinter functions simpleand convenient.
Automatic paper cutter(Controlled by command)
(TSP442)
POWERHEAD UPNO PAPERERROR
ON LINE
FEED
ON
OFF
ON
OFF
Power switchSwitches power on or off.
Connector cover
Interface connectorConnects the computer to the printer.
Peripheral drive connectorOnly connects to peripheral unitssuch as each drawers, etc.
Release barOpens and closes the print head unit which holdsthe paper against the platen.
(TSP412)
– 3 –
EN
GLIS
H
3. FERRITE CORE INSTALLATION *EUROPE ONLY
NOTE: Take special care when following the procedures listed below.
Two ferrite core noise filters, large and small, come packed with the printer.The small noise filter is for the RS232C serial interface cable, while the largerone is for the cable of peripheral units.
Fig. 3-4
Fig. 3-3
Fig. 3-1
Pass fastener through ferrite core.
Pass fastener around cable and lock it.Cut off excess with scissors.
ProductCodeModelName
09990723
Ferrite CoreTFC-23-11-14
ProductCodeModelName
09990728
Ferrite CoreTFC-20-10-10
For Interface Cable For Peripheral Unit Cable
Ø28mmØ24mm
The ferrite cores are packed so theyare open, as shown in Fig. 3-2. If youfind that a ferrite core is not open, usea pointed object to pry the plastic lockof the ferrite core apart (Fig. 3-1).When you do, take care not to damagethe ferrite core or the plastic lock.
5cm maximum
Fastener
Pull and cut
Small ferrite Core(24mm diameter)
Interface
Cable
Fig. 3-2
– 4 –
EN
GLI
SH
Installation of the interface cable ferrite core
Clamp the small ferrite core onto the interface cable as shown in Fig. 3-2. Takecare to avoid damaging the interface cable when installing the ferrite core. Theferrite core should be anchored firmly in place with the fastener that comeswith it, as shown in Fig.3-3 and 3-4.
Installation of the peripheral unit cable ferrite core
Clamp the large ferrite core onto the cable of the interface unit using the sameprocedure as you do for the interface cable ferrite core. With the peripheral unitcable ferrite core, however, you have to loop the cable as shown in Fig. 3-5.
Fig. 3-5
Ground wireOne loop
Large ferrite core(28mm diameter)
5cm or less
– 5 –
EN
GLIS
H
4. CONNECTING THE INTERFACE CABLE4-1. RS-232C or RS-422A Serial interface
Follow the procedures below to connect the interface cable:
Fig. 4-1
1 Switch off the power to the printerand computer.
2 Insert the interface cable into theconnector. (Be sure that the cable isoriented correctly before insertingit.)
3 Fasten the right and left screws tofix them in place on the connector.
4 Connect the other end of the inter-face cable to your computer.
Interface cable
Interface connector
NOTE: The data transfer conditions between the computer and the printer mustbe made compatible with the DIP switch settings on the printer. (Referto “APPENDIX”.)
4-2. Centronics-type Parallel interface
1 Switch off the power to the printerand computer.
2 Insert the interface cable into theconnector. (Be sure that the cable isoriented correctly before insertingit.)
3 Fasten the connector clasps.
4 Connect the other end of the inter-face cable to your computer.Fig. 4-2
TABLE DES MATIERES1. DEBALLAGE ET INSPECTION .......................................................7
1-1. Déballage .....................................................................................71-2. Remarques sur la manipulation .................................................... 7
2. IDENTIFICATION DES PIECES ET NOMENCLATURE ...............8
3. INSTALLATION DU TORE DE FERRITE *EUROPE UNIQUEMENT......9Installation du tore de ferrite de câble d’interface .............................10Installation du tore de ferrite de câble de périphérique .....................10
4. RACCORDEMENT DU CÂBLE D’INTERFACE ...........................114-1. Interface série RS-232C ou RS-422A ........................................ 114-2. Interface parallèle type Centronics ............................................ 11
APPENDICE ...........................................................................................24
L’appendice n’est pas traduit.
– 7 –
FR
AN
ÇA
IS
1. DEBALLAGE ET INSPECTION1-1. Déballage
Vérifier chaque pièce de la boîte en se référant à la Figure 1 afin de s’assurer qu’ona bien tout reçu (il doit y avoir cinq pièces).En cas d’absence d’une de ces pièces, contacter le fournisseur.
Fig. 1-1
1-2. Remarques sur la manipulation
Avant de commencer l’installation de l’imprimante, s’assurer qu’on dispose biend’un endroit approprié pour la mettre. Un “endroit approprié” doit satisfaire auxconditions suivantes:• A proximité d’une prise d’accès facile• Surface ferme et à niveau pratiquement sans aucunes vibrations• A distance de toute chaleur excessive (par exemple lumière du soleil directe,
radiateurs etc.)• A distance de toute humidité excessive• A distance de poussière excessive• Accès à une source d’alimentation constante ne subissant pas de pointes
d’alimentation. Ainsi, par exemple, il ne faut pas relier l’imprimante au mêmecircuit qu’un appareil important bruyant du genre réfrigérateur ou climatiseur.
REMARQUE: S’assurer que la tension de ligne correspond à la tension indiquéesur la plaque signalétique de l’imprimante.
Ø24mm Ø28mm
Manuel d’utilisationManuel d’installation Attache
(Europe uniquement)
Tore de ferrite decâble d’interface(Europeuniquement)
Tore de ferritede câble depériphérique(Europeuniquement)
Rouleau de papier échantillonArbre du rouleaude papier
Imprimante
– 8 –
FR
AN
ÇA
IS
Automatic paper cutter(Controlled by command)
(TSP442)
2. IDENTIFICATION DES PIECES ET NOMENCLATURESe référer à la Figure 2-1 pour se familiariser avec les composants et capacités del’imprimante.
Fig. 2-1
ON
OFF
ON
OFF
Couvercle du connecteur
Connecteur d’interfaceRelie l’ordinateur à l’imprimante
Barre de déclenchementOuvre et ferme la tête d’impression qui retient lepapier contre le cylindre.
Couvercle d’imprimanteProtège la tête d’impression ainsique d’autres composants internesde l’imprimante.
POWERHEAD UPNO PAPERERROR
ON LINE
FEED
(TSP412)
Couteau de papierautomatique(pilotage par commande)
Tableau de commandeIndique l’état de l’imprimante etsimplifie les fonctions decommande de l’imprimante tout enfacilitant leur exécution.
Interrupteur d’alimentationConnecte ou coupe l’alimentation
Connecteur d’entraînement depériphériqueConnexion uniquement à despériphériques du genre caissesenregistreuses etc.
– 9 –
FR
AN
ÇA
IS
3. INSTALLATION DU TORE DE FERRITE *EUROPE UNIQUEMENT
REMARQUE: Prendre des précautions spéciales en suivant les procéduresindiquées ci-dessous:
Deux filtres antibruit à tore de ferrite, un grand et un petit sont emballés avecl’imprimante. Le petit filtre antibruit est prévu pour le câble d’interface sérieRS232C et le grand doit être utilisé pour le câble de périphérique.
Fig. 3-4
Faire passer l’attache autour du câble etla bloquer. Couper toute partie qui dé-passe avec des ciseaux.
Pull and cutTirer et couper
Les tores de ferrite sont livrés ouvertscomme indiqué à la Fig. 3-2. Si un torede ferrite n’est pas ouvert, utiliser unobjet pointu pour forcer le verrouillageen plastique du tore de ferrite (Fig.3.1). Lorsque c’est le cas, prendresoin de ne pas endommager le tore deferrite ni le verrouillage en plastique. Fig. 3-1
Code duproduitNom dumodèle
09990723
Tore de ferriteTFC-23-11-14
Code duproduitNom dumodèle
09990728
Tore de ferriteTFC-20-10-10
Pour le câble d’interface Pour le câble de périphérique
Ø28mmØ24mm
Small ferrite Core(24mm diameter)
Interface
Cable
Fig. 3-2
Petit tore de ferrite (diamètre 24 mm)
Interface
Câble
Faire passer l’attache par le tore de ferrite
5cm maximum
Fastener
5 cmmaximum
Attache
Fig. 3-3
– 10 –
FR
AN
ÇA
IS
Installation du tore de ferrite de câble d’interface
Serrer le petit tore de ferrite au câble d’interface de la manière indiquée à la Fig.3-2. Prendre les précautions d’usage pour éviter d’endommager le câbled’interface lors de l’installation du tore de ferrite. Il faut bien immobiliser letore de ferrite au moyen de l’attache fournie, comme indiqué à la Fig. 3-3 et àla Fig. 3-4.
Installation du tore de ferrite de câble de périphérique
Serrer le grand tore de ferrite au câble d’interface en suivant la même procédureque celle du tore de ferrite du câble d’interface. Dans le cas du tore de ferritedu câble de périphérique, il faut toutefois faire une boucle avec le câble de lamanière indiquée à la Fig. 3-5.
Fig. 3-5
Ground wireOne loop
Large ferrite core(28mm diameter)
5cm or less5 cm ou moinsGrand tore de ferrite(diamètre 28 mm)
Fil à la terre Une seule boucle
– 11 –
FR
AN
ÇA
IS
4. Raccordement du câble d’interface4-1. Interface série RS-232C ou RS-422A
Suivre les procédures indiquées ci-dessous pour relier le câble d’interface
Fig. 4-1
1 Couper l’alimentation à l’impri-mante et à l’ordinateur.
2 Insérer le câble d’interface dans leconnecteur. (S’assurer que le câbleest orienté correctement avant del’insérer).
3 Serrer les vis droite et gauche pourles immobiliser sur le connecteur.
4 Relier l’autre extrémité du câbled’interface à l’ordinateur.
Interface cable
Interface connector
REMARQUE: Rendre compatibles les conditions de transfert de données entrel’ordinateur et l’imprimante en réglant les microrupteurs del’imprimante en conséquence. (Se référer à “ANNEXE”).
4-2. Interface parallèle type Centronics
1 Couper l’alimentation à l’impri-mante et à l’ordinateur.
2 Insérer le câble d’interface dans leconnecteur. (S’assurer que le câbleest orienté correctement avant del’insérer).
3 Fermer les attaches du connecteur.
4 Relier l’autre extrémité du câbled’interface à l’ordinateur.
Câble d’interface
Connecteur d’interface
Fig. 4-2
INHALTSVERZEICHNIS1. AUSPACKEN UND KONTROLLE ................................................ 13
1-1. Auspacken .................................................................................. 131-2. Hinweise .....................................................................................13
2. FUNKTION UND BEZEICHNUNG DER EINZELNEN BAUTEILE ..14
3. INSTALLATION DER FERRITKERNE *NUR EUROPA .....................15Installation des Ferritkerns für das Schnittstellenkabel .....................16Installation des Ferritkerns für das Peripheriegerätekabel ................ 16
4. ANSCHLUSS DES SCHNITTSTELLENKABELS ........................ 174-1. Serielle Schnittstellen RS-232C oder RS-422A.........................174-2. Parallele Centronics-Schnittstelle .............................................. 17
ANHANG ................................................................................................ 24
Der Anhang erscheint nur im englischen Teil dieser Bedienungsanleitung
– 13 –
DE
UT
SC
H
1. AUSPACKEN UND KONTROLLE1-1. Auspacken
Überprüfen Sie an Hand von Abbildung 1 die Teile in der Verpackung, und stellenSie sicher, daß alle nötigen Positionen geliefert wurden; es sollten fünf sein.Falls eines der Teile fehlen sollte, wenden Sie sich bitte an Ihren Händler.
Abb. 1-1
1-2. Hinweise
Wählen Sie für die Aufstellung Ihres Druckers zunächst einen geeigneten Platzaus. Er sollte folgende Merkmale aufweisen:• Er sollte nahe einer leicht zugänglichen Netzsteckdose sein.• Er sollte eine stabile, ebene und erschütterungsfreie Oberfläche haben.• Er sollte nicht übermäßiger Hitze ausgesetzt sein (wie direktem Sonnenlicht,
einer Heizung usw.).• In der Druckerumgebung sollte keine übermäßige Luftfeuchtigkeit herrschen.• Sie sollte nicht übermäßig staubig sein.• Die Stromversorgung sollte stabil und nicht anfällig für Störungen sein. Sie
sollten den Drucker zum Beispiel nicht an einem Stromkreis zusammen mitgroßen, eventuell Störungen verursachenden Geräten wie Kühlschrank oderKlimaanlage betreiben.
HINWEIS: Stellen Sie sicher, daß die Spannung Ihres Stromnetzes der Betriebs-spannung entspricht, die auf dem Typenschild des Druckers ange-geben ist.
BedienungsanleitungAufstellanleitung Kabelbinder
(nur EU)
Ferritkern für dasSchnittstellenkabel(nur EU)
Ferritkern fürPeripheriege–rätekabel(nur EU)
Papierrolle
Drucker
Achse für diePapierrolle
Ø24mm Ø28mm
– 14 –
DE
UT
SC
H
2. FUNKTION UND BEZEICHNUNG DER EINZELNEN BAUTEILEMachen Sie sich in Abbildung 2-1 mit den Bestandteilen des Druckers und seinenFunktionen vertraut.
Abb. 2-1
EntriegelungshebelMit ihm wird die Druckkopfeinheit entlastet undangepreßt, mit der das Papier an die Walze gedrückt wird.
DruckerklappeSie schützt den Druckkopf undandere Bauteile im Inneres IhresDruckers.
Automatic paper cutter(Controlled by command)
(TSP442)
POWERHEAD UPNO PAPERERROR
ON LINE
FEED
(TSP412)
AutomatischerPapierschneider(befehlsgesteuert)
BedienfeldEs zeigt den Druckerstatus an, undmit ihm lassen sich dieDruckerfunktionen bequem undeinfach steuern.
ON
OFF
ON
OFF
Buchse für PeripheriegeräteSie dient zum Anschluß vonPeripheriegeräten wie etwa Geldladen,etc.
SchnittstellenbuchseAn ihr wird der Computer an den Druckerangeschlossen.
Abdeckung für dieSchnittstellenbuchse
NetzschalterMit ihm wird das Gerät an- undausgeschaltet.
– 15 –
DE
UT
SC
H
5cm maximum
Fastener
3. INSTALLATION DER FERRITKERNE *NUR EUROPA
HINWEIS: Beachten Sie die folgenden Schritte besonders sorgfältig.
Zwei Ferritkerne zum Filtern von Störungen – ein großer und ein kleiner –werden mit dem Drucker geliefert. Der kleine Entstörungsfilter findet amKabel für die serielle RS232C-Schnittstelle Verwendung, das große am Kabelfür Peripheriegeräte.
Abb. 3-4
Die Ferritkerne werden in der offenenStellung geliefert, siehe Abbildung 3-2. Sollte ein Ferritkern nicht offensein, öffnen Sie den Plastikverschlußdes Ferritkerns mit einem spitzen Ge-genstand (Abbildung 3-1). Achten Siedabei darauf, daß Sie weder Ferritkernnoch Plastikverschluß beschädigen. Abb. 3-1
Produkt-nummer 09990723
FerritkernTFC-23-11-14
Produkt-nummer 09990728
FerritkernTFC-20-10-10
für das Schnittstellenkabel für das Peripheriegerätekabel
Ø28mmØ24mm
Small ferrite Core(24mm diameter)
Interface
Cable
Abb. 3-2
kleiner Ferritkern (24 mm Durchmesser)
Stecker
Kabel
Abb. 3-3
Modell Modell
Führen Sie den Kabelbinder durch dieÖse am Ferritkern.
5 cmMaximalabstand
Kabelbinder
Pull and cutStraffziehen undabschneiden
Führen Sie den Kabelbinder um dasKabel, und ziehen Sie ihn fest. Schnei-den Sie das überstehende Ende mit einerSchere ab.
– 16 –
DE
UT
SC
H
Installation des Ferritkerns für das Schnittstellenkabel
Klemmen Sie den kleinen Ferritkern auf das Schnittstellenkabel, siehe Abbil-dung 3-2. Achten Sie darauf, daß bei der Installation des Ferritkerns das Kabelnicht beschädigt wird. Der Ferritkern sollte mit dem mitgelieferten Kabelbindersicher an seinem Platz befestigt werden. Siehe Abbildungen 3-3 und 3-4.
Installation des Ferritkerns für das Peripheriegerätekabel
Klemmen Sie den großen Ferritkern auf das Kabel für die Peripheriegeräte.Gehen Sie dabei genauso vor wie oben beim Schnittstellenkabel beschrieben.Bei diesem Ferritkern allerdings müssen Sie das Kabel in einer Schlaufe laufenlassen, wie in Abbildung 3-5 gezeigt.
Abb. 3-5
Ground wireOne loop
Large ferrite core(28mm diameter)
5cm or less5 cm oder wenigergroßer Ferritkern(28 mm Durchmesser)
Massekabel eine Schlaufe
– 17 –
DE
UT
SC
H
4. ANSCHLUSS DES SCHNITTSTELLENKABELS4-1. Serielle Schnittstellen RS-232C oder RS-422A
Gehen Sie zum Anschluß des Schnittstellenkabels vor wie unten beschrieben.
Abb. 4-1
1 Schalten Sie Drucker und Compu-ter aus.
2 Stecken Sie das Schnittstellenkabelin die Buchse. (Vergewissern Siesich, daß das Kabel korrekt ausge-richtet ist, bevor Sie den Steckereinstecken.)
3 Ziehen Sie die beiden Schrauben linksund rechts fest, so daß der Steckersicher an der Buchse befestigt ist.
4 Verbinden Sie das andere Ende desKabels mit Ihrem Computer.
Interface cable
Interface connectorBuchse
Schnittstellenkabel
HINWEIS: Die Datenübertragungsparameter von Computer und Drucker müs-sen übereinstimmen. Sie werden mit den DIP-Schaltern des Druk-kers eingestellt (siehe »Anhang«).
4-2. Parallele Centronics-Schnittstelle
1 Schalten Sie Drucker und Compu-ter aus.
2 Stecken Sie das Schnittstellenkabelin die Buchse. (Vergewissern Siesich, daß das Kabel korrekt ausge-richtet ist, bevor Sie den Steckereinstecken.)
3 Klammern Sie den Stecker an derBuchse fest.
4 Verbinden Sie das andere Ende desKabels mit Ihrem Computer.
Abb. 4-2
INDICE1. APERTURA E CONTROLLO DELLA CONFEZIONE .................19
1-1. Apertura della confezione .......................................................... 191-2. Avvertenze .................................................................................19
2. IDENTIFICAZIONE E NOMENCLATURA DELLE PARTI ........ 20
3. INSTALLAZIONE DEGLI ANELLI DI FERRITE *SOLO EUROPA ..21Installazione dell’anello di ferrite del cavo d’interfaccia .................. 22Installazione dell’anello di ferrite del cavo dell’unità periferica ...... 22
4. COLLEGAMENTO DEL CAVO D’INTERFACCIA .....................234-1. Interfaccia seriale RS-232C o RS-422A .................................... 234-2. Interfaccia parallela tipo Centronics .......................................... 23
APPENDICE ...........................................................................................24
L’Appendice appare solo nella sezione in inglese di questo manuale.
– 19 –
ITA
LIAN
O
1. APERTURA E CONTROLLO DELLA CONFEZIONE1-1. Apertura della confezione
Confrontare il contenuto della confezione con i componenti mostrati nella Figura1-1 per controllare di aver ricevuto tutto (nella scatola dovrebbero esserci cinquecomponenti).Nel caso mancasse qualcuna di queste parti, contattare il fornitore presso cui siè effettuato l’acquisto.
Fig. 1-1
1-2. Avvertenze
Prima dell’installazione della stampante, assicurarsi di disporre di un luogoadatto in cui collocarla. Per “luogo adatto”, intendiamo un luogo:• vicino ad una presa elettrica facilmente accessibile• su una superficie solida e piana che non subisca vibrazioni• lontano da fonti di calore eccessivo (come luce diretta del sole, apparecchi di
riscaldamento, ecc.)• lontano da umidità eccessiva• lontano da polvere eccessiva• con la possibilità di accedere ad una fonte di alimentazione elettrica stabile
non soggetta a sbalzi improvvisi di tensione. Ad esempio, non collegare lastampante sullo stesso circuito elettrico di grossi apparecchi che produconodisturbi come frigoriferi o condizionatori d’aria.
NOTA: Assicurarsi che la tensione del proprio impianto elettrico corrisponda aquella specificata sulla piastrina di identificazione della stampante.
Manuale di istruzioniManuale di installazione Fascetta di fissaggio
(solo Europa)
Anello di ferriteper cavod’interfaccia(solo Europa)
Anello di ferriteper cavo unitàperiferica (soloEuropa)
Rotolo di carta campione
Stampante
Asta delrotolo di carta
Ø24mm Ø28mm
– 20 –
ITA
LIA
NO
2. IDENTIFICAZIONE E NOMENCLATURA DELLE PARTIEsaminare la Figura 2-1 per conoscere i componenti e le funzionalità dellastampante.
Fig. 2-1
Barra di aperturaServe per aprire e chiudere l’unità della testina di stampache mantiene premuta la carta contro il rullo.
Coperchio della stampanteProtegge la testina di stampa egli altri componenti interni dellastampante.
Automatic paper cutter(Controlled by command)
(TSP442)
POWERHEAD UPNO PAPERERROR
ON LINE
FEED
(TSP412)
Taglierina della cartaautomatica(Controllata tramite comando)
Pannello di controlloIndica lo stato della stampante esemplifica il controllo dellefunzioni della stampante.
ON
OFF
ON
OFF
Connettore d’interfacciaServe per collegare la stampante al computer.
Interruttore di alimentazioneServe ad accendere e spegnerela stampante. Coperchio del
connettore
Connettore unità perifericaServe per collegare la stampante adunità periferiche, come registratori dicassa, ecc.
– 21 –
ITA
LIAN
O
3. INSTALLAZIONE DEGLI ANELLI DI FERRITE *SOLO EUROPA
NOTA: Prestare particolare attenzione durante l’esecuzione delle procedureindicate di seguito.
Insieme alla stampante vengono forniti in dotazione due anelli di ferrite, unogrande e uno piccolo, da utilizzare come filtri per la soppressione di eventualidisturbi. Il filtro antidisturbi piccolo va fissato sul cavo d’interfaccia serialeRS232C, mentre quello grande serve per il cavo di collegamento di unitàperiferiche.
Fig. 3-4
5cm maximum
Fastener
Gli anelli di ferrite sono confezionatiaperti, come mostrato in Fig. 3-2. Se sitrova uno degli anelli di ferrite chiuso,aprirlo utilizzando un oggettoappuntito per far leva sul dispositivodi chiusura di plastica dell’anello diferrite (Fig. 3-1). Fare attenzione anon danneggiare il nucleo di ferrite oil dispositivo di chiusura di plastica.
Abb. 3-1
Fig. 3-3
Far passare la fascetta di fissaggio attra-verso l’anello di ferrite.
Distanzamassima 5 cm
Pull and cut
Far passare la fascetta di fissaggio intor-no al cavo e bloccarla. Tagliare la partein eccesso con delle forbici.
Fascetta di fissaggio
Tirare e tagliare
Small ferrite Core(24mm diameter)
Interface
Cable
Fig. 3-2
Anello di ferrite piccolo (diametro 24 mm)
Interfaccia
Cavo
Codiceprodotto 09990723
Anello di ferriteTFC-23-11-14
Codiceprodotto 09990728
Anello di ferriteTFC-20-10-10
Per il cavo d’interfaccia Per il cavo dell’unità periferica
Ø28mmØ24mm Modello Modello
– 22 –
ITA
LIA
NO
Installazione dell’anello di ferrite del cavo d’interfaccia
Fissare l’anello di ferrite piccolo sul cavo d’interfaccia come mostrato in Fig.3-2, facendo attenzione a non danneggiare il cavo d’interfaccia. L’anello diferrite va saldamente bloccato in posizione con la fascetta di fissaggio fornitain dotazione, come mostrato nelle Fig. 3-3 e 3-4.
Installazione dell’anello di ferrite del cavo dell’unità periferica
Fissare l’anello di ferrite grande sul cavo dell’unità periferica eseguendo lastessa procedura vista per l’anello di ferrite del cavo d’interfaccia. Tuttavia,quando si applica l’anello di ferrite sul cavo dell’unità periferica, è necessariofare un cappio al cavo come mostrato in Fig. 3-5.
Fig. 3-5
Ground wireOne loop
Large ferrite core(28mm diameter)
5cm or lessDistanza di 5 cm o inferiore
Filo di terra Cappio
Anello di ferrite grande(diametro 28 mm)
– 23 –
ITA
LIAN
O
4. COLLEGAMENTO DEL CAVO D’INTERFACCIA4-1. Interfaccia seriale RS-232C o RS-422A
Per collegare il cavo d’interfaccia, eseguire le procedure indicate di seguito:
1 Spegnere sia la stampante che ilcomputer.
2 Inserire il cavo d’interfaccia nelconnettore (assicurarsi che il cavosia orientato nel senso corretto pri-ma di inserirlo).
3 Stringere le due viti di destra e sini-stra per fissare il connettore.
4 Collegare l’altra estremità del cavod’interfaccia al computer.
Interface cable
Interface connectorConnettore d’interfaccia
Cavo d’interfaccia
Fig. 4-1
NOTA: Le caratteristiche di trasferimento dati tra il computer e la stampantedevono essere rese compatibili attraverso le impostazioni degli interrut-tori DIP della stampante (vedere l’“APPENDICE”).
4-2. Interfaccia parallela tipo Centronics
1 Spegnere sia la stampante che ilcomputer.
2 Inserire il cavo d’interfaccia nelconnettore (assicurarsi che il cavosia orientato nel senso corretto pri-ma di inserirlo).
3 Bloccare i fermagli del connettore.
4 Collegare l’altra estremità del cavod’interfaccia al computer.Fig. 4-2
– 24 –
AP
PE
ND
IX
APPENDIXDIP SWITCHES
DIP switches are located on the interface board. The number of switches variesaccording to the board, as follows.
Centronics No DIP switchesRS-232C One 8-bit DIP switchRS-422A One 8-bit DIP switch and one 4-bit DIP switch
8
1
ON OFF
– 25 –
AP
PE
ND
IX
DIP-switch settings
a) DIP switch #1 (RS-232C, RS-422A)
Switch Setting ON OFF1-1 Baud1-2 Baud1-3 Handshaking DTR X-ON/X-OFF1-4 Data bits 8 bits 7 bits1-5 Parity type Not used Used1-6 Parity type Odd Even1-7 DCI/DC3 Invalid Valid (RS-232C only)1-8 When turning power ON * Refer to the table below.
Baud 1-1 1-22400BPS OFF OFF4800BPS OFF ON9600BPS ON ON19200BPS ON OFF
Factory settings : ALL ON
* When the printer’s power is ON.
ON OFFDC1/DC3 valid mode Select DeselectAdressable mode Deselect Select (RS-422A only)DC1/DC3 invalid mode Select Select
b) DIP switch #2 (RS-422A only)
DIP SW 2 (RS-422A only)
Function DC1/DC3 Addressable mode *2 DC1/DC3
Switch invalid mode #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 #12 #13 #14valid mode
2-1 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF
2-2 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF
2-3 ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF
2-4 ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF
– 26 –
AP
PE
ND
IX
Print Density Adjustment
Since the sensitivity of different types of heat-sensitive paper varies, you canadjust the print density by varying the current supplied to the thermal head.
The print density can be adjusted using the variable resistor inside the hole besidethe interface connector on the back of the printer.
1. To adjust the density turn the resistor roughly two times using a small cross-head screwdriver.
2. Turn the resistor to the right (clockwise) for a darker print density or to the left(counterclockwise) for a lighter density.
NOTE: If the density is increased to a higher level than necessary when printingon highly sensitive heat-sensitive paper, the dots may be too large and theprint quality may decrease.Excessively high energy adjustment may reduce head life.
Variable resistorused to adjust theprint density
– 27 –
AP
PE
ND
IX
Sensor Adjustment
Sensor levels are adjusted at the factory. If necessary, you can readjust thelevels as described below.
1) Remove the ROM cover located beneath the paper-roll holding area.
2) Hold down the FEED and ON LINE switches while switching on the power, andcontinue to hold them down until you hear a triple beep. (This will take aboutfive seconds.) When you hear the triple beep, release the buttons to entersensor-adjustment mode.
a) Reflective Sensor• Insert a non-black area of paper into the mechanism’s sensor area.• Rotate the main PCB’s sensor adjustment knob (VR4) to the point where the
HEAD UP indicator comes on.
b) Paper-Out Sensor• Insert a non-black area of paper into the mechanism’s sensor area.• Rotate the main PCB’s sensor adjustment knob (VR3) to the point where the
NO PAPER indicator comes on.
c) Transmissive Sensor• Insert the backing portion of a label sheet into the mechanism’s transmissive
sensor area. (Insert the backing part only, not the label itself.)• Adjust the main PCB’s coarse (VR1) and fine (VR2) adjustment knobs to the
point where the ERROR indicator comes on.
NOTE: When inserting paper, be sure to lower the head so that it is close toits normal fixed position.
– 28 –
AP
PE
ND
IX
EPROM
VR4
Variable Resistances (Sensor Adjustment Knobs)
Main PCB
Interface PCB
VR2
VR3VR1
– 29 –
AP
PE
ND
IX
Connectors and Signal Names (Serial Interface)
RS-232C Interface
Pin no Signal name Direction Function1 F-GND – Frame ground2 TXD OUT Outgoing data3 RXD IN Incoming data4 RTS OUT Request To Send: The printer sets this signal
to “SPACE” when it is ready to send.5 CTS IN The host sets this signal to “SPACE” when it
is ready to send. NOTE: The printer does notmonitor this signal.
6 N/C Not used7 S-GND – Signal ground8 N/C Not used9 ~ 10 N/C Not used11 RCH OUT The printer sets this signal to “SPACE” when
it is ready to receive. This pin outputs thesame signal as pin 20, to which it is con-nected.
12 N/C Not used13 S-GND – Signal ground.14 FAULT OUT The printer sets this signal to “MARK” to
indicate an error condition (machine error, nopaper, etc.).
15 Multi-Printer TXD OUT Diode gate TXD16 Multi-Printer DTR OUT Diode gate DTR17 ~ 19 N/C Not used20 DTR OUT Data Terminal Ready: The printer sets this
signal to “SPACE” when it is ready to re-ceive.
21 ~ 22 N/C Not used23 ~ 25 N/C Not used
13 1
1425
– 30 –
AP
PE
ND
IX
These pins carry data from the printer.
These pins carry data to the printer.
The host sets this signal to “SPACE” when itis ready to send.NOTE: The printer does not monitor thissignal.
The host sets this signal to “SPACE” when itis ready to receive.NOTE: The printer does not monitor thissignal.The printer sets this signal to “SPACE” whenit is ready to receive.The printer sets this signal to “SPACE” whenit is ready to receive.
RS-422A Interface
Pin no Signal name Direction Function9 SD(+) OUT10 SD(–) OUT17 RD(+) IN18 RD(–) IN19 CS(+) IN
23 CS(–) IN
24 RS(+) OUT
25 RS(–) OUT
Interface Connections
Refer to the host computer’s interface specifications for details of how to connectthe interface. The following illustrations show typical connection configura-tions.
[RS-232C]
1
2
3
4
5
7
14
20
1
2
3
4
5
6
7
8
20
F-GND
TXD
RXD
RTS
CTS
DSR
S-GND
DCD
DTR
F-GND
TXD
RXD
RTS
CTS
S-GND
FAULT
DTR
Printer side IBM PC side
– 31 –
AP
PE
ND
IX
[RS-422A]
1718
9
10
Twisted pair cablePrinter #nRD
SD
SD
RD
1718
9
10
Printer #n+1RD
SD
Printer side Host side
– 32 –
AP
PE
ND
IX
Connectors and Signal Names (Parallel Interface)
(18) (1)
(36) (19)
Conforms to Amphenol connector 57-30360
(Printer Side)
Signal Name Sample Circuit
Inpu
tO
utpu
t
DATA 1
DATA 8
STROBE
BUSYACK
~
4.7kΩ
74LS-equivalent
1kΩ
100Ω
1000pF
74LS-equivalent
1.8kΩ74LS-equivalent
– 33 –
AP
PE
ND
IX
PAIR RETURN
Pin no Signal name Direction Function
1 STROBE IN Strobe pulse for data read. Usually HIGH;goes LOW to trigger data read.
2-9 DATA 1~8 IN Parallel data lines for eight-bit data. HIGHis “1”; LOW is “0”.
10 ACK OUT Printer outputs this pulse for approxi-mately 9µs to indicate that data read iscompleted. Printer becomes ready toreceive new data at the moment the ACKpulse ends.
11 BUSY OUT DC-level signal indicating printer’s currentstatus. LOW indicates that printer is ready toreceive the next data; HIGH indicates thatprinter is unable to receive. The printer holdsthis signal “HIGH” during any of the follow-ing conditions.1 While data entry is in progress2 While printer is offline 3 While errorcondition exists
12 PAPER OUT OUT DC-level signal indicating whether printerhas paper. The signal stays LOW while paperis present; it goes HIGH to indicate that paperhas run out.
13 SELECTED OUT DC-level signal; stays HIGH while printer isonline.
14-15 N/C Not used16 SIGNAL GND Signal ground17 CHASSIS GND Printer-frame ground18 +5V Outputs +5V (Max. 50mA)19-30 TWISTED Return pins for various signals. Each pin is
connected to the corresponding signal line bytwisted pair line.
31 RESET IN LOW level causes printer to reset its controlcircuitry and return to its initial state.
32 ERROR OUT Goes LOW to indicate that printer is unable toprint.
33 EXT GND Ground terminal for external connection34-35 N/C Not used36 – – Fixed “HIGH” at printer side
– 34 –
AP
PE
ND
IX
16
Modular plug MOLEX 90075-0007,AMP641337 or JAPAN BURNDY B-66-4
Shield
Wire lead
Separated Ground wireconnected to shield (Europe only).
Ground wire1 turn
Ferrite core
Distance within 5cm.
Peripheral Unit Drive Circuit
A drive circuit for driving peripheral units (such as cash drawers) is featured onthe main logic board of this printer. A modular connector for driving peripheralunits is featured on the output side on the drive circuit. When using this circuit,connect the cable for the peripheral unit. (Cables must be prepared by the user.)Note that Page Mode does not support external-device drive commands. Drivecommands are available only in Line Mode.
Use cables which meet the following specifications.1. Use the modular plug as shown in Figure 17.2. Separate ground wire is required for Europe only.3. Use if the printer is to be used in Europe, the Ferrite core and the cable should
be separate, as shown in Figure 18.
CAUTION : DO NOT connect any other plug to the peripheral unit connector.
Cable specifications for peripheral unit.
Separate ground wire and noise filter are required for Europe.
– 35 –
AP
PE
ND
IX
[Drive output 24V, max. 1.0 A]
7824
F.G
TR1
M-GND
TR2
M-GND
TR3
+5V
+24V
R1
R2
6
5
4
3
2
1
L1
L2
R34.7kΩ1/4W
Frameground
D1
D2
Peripheralunit 1
With shield
Peripheralunit 2
Compulsionswitch
Drive circuitThe recommended drive circuit is shown.
NOTES:1. Peripheral units #1 and #2 cannot be driven simultaneously.
When driving a device continuously, do not use drive duty above 20%.2. Compulsion switch status is available as status data.3. Resistance for coils L1 and L2 is not less than 24 ohms.4. Absolute maximum ratings for diodes D1 and D2 (at Ta=25˚C):
Average rectified current Io = 1AMaximum forward surge current (60Hz,1-cycle sine wave) IFSM=40A
5. Absolute maximum rating for transistors TR1 and TR2 (at Ta = 25˚C):Collector current Ic = 2A
P 1996.1
Printed in Japan, 80871025
HEAD OFFICESTAR MICRONICS CO., LTD.20-10 Nakayoshida, Shizuoka, 422 JapanTel: (054) 263-1115, Telefax: (054) 263-8714
OVERSEAS SUBSIDIARY COMPANIESSTAR MICRONICS AMERICA, INC.70-D Ethel Road West, Piscataway, NJ 08854 U.S.ATel: (908) 572-9512, Telefax: (908) 572-5095,Telex: 299766 STAR UR
STAR MICRONICS DEUTSCHLAND GMBHWesterbachstraße 59, D-60489 Frankfurt/Main 90, GermanyTel: 0697-89990, Telefax: 0697-81006, Telex: 417 5825 STAR D
STAR MICRONICS U.K. LTD.Star House, Peregrine Business Park, Gomm Road,High Wycombe, Bucks, HP13 7DL, UKTel: 01494-471111, Telefax: 0494-473333