TREATING POOLS WITH BANISH TO REMOVE ALGAE...TREATING POOLS WITH BANISH TO REMOVE ALGAE cannot see...

2
INTRODUCTION If your pool is turning green, has algae spots in it or is otherwise discolored, the pool most likely has algae. One of the best ways to get rid of algae is by using BioGuard ® Algae Banish™. Banish is a highly effective, patented, non-staining algaecide that kills all types of algae in swimming pools. It is formulated for use in chlorine or bromine sanitized swimming pools only. Be sure and read the important notes on the bottle before using. STEP ONE: If your pool is clear or only slightly hazy, proceed to step two. If your pool is so cloudy or the algae is so extensive that you TREATING POOLS WITH BANISH TO REMOVE ALGAE cannot see the bottom in areas of the pool where the water is 3 to 4 feet deep, use PowerFloc. Be sure to follow the label directions on PowerFloc. After completing the final step of the PowerFloc usage – vacuuming to waste – proceed to step two. STEP TWO: Vacuum away any debris in the pool. Thoroughly brush all pool surfaces with a surface compatible brush. STEP THREE: With the pump and filter operating, apply one (1) pound of Burn Out Ex- treme per 7,000 gallons of pool water or one (1) pound of Burn Out 35 per 6,000 gallons of pool water. Be sure to brush any undissolved product off any bleachable surfaces. STEP FOUR: Continue to operate pump and filter for one hour. STEP FIVE: With pump and filter operating, apply sixteen (16) ounces of Banish per 10,000 gallons of pool water, pouring the product directly into the pool in the areas of heaviest algae growth. STEP SIX: Keep the pump and filter operating continuously for the next 24 hours. STEP SEVEN: After 24 hours, thoroughly brush all pool surfaces. STEP EIGHT: Continue to operate the pump and filter continuously for the next 24 hours. Copyright ©2006 ULTRA MODERN POOL & PATIO, INC. _____________________________________ NOTE: Always follow label directions and manufacturers instructions for each product used. Conditions may vary from pool to pool. Ultra Modern Pool & Patio does not assume any responsibility or liability for the results that may be obtained through utilization of this or any other program, procedure or product. SPECIAL INSTRUCTIONS: ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________ ______________________________________

Transcript of TREATING POOLS WITH BANISH TO REMOVE ALGAE...TREATING POOLS WITH BANISH TO REMOVE ALGAE cannot see...

Page 1: TREATING POOLS WITH BANISH TO REMOVE ALGAE...TREATING POOLS WITH BANISH TO REMOVE ALGAE cannot see the bottom in areas of the pool where the water is 3 to 4 feet deep, use PowerFloc.

INTRODUCTION

If your pool is turning green, has algae spots in it

or is otherwise discolored, the pool most likely has

algae.

One of the best ways to get rid of algae is by

using BioGuard® Algae Banish™. Banish is a

highly effective, patented, non-staining algaecide

that kills all types of algae in swimming pools. It is

formulated for use in chlorine or bromine sanitized

swimming pools only. Be sure and read the

important notes on the bottle before using.

STEP ONE: If your pool is clear or only

slightly hazy, proceed to step two. If your pool is

so cloudy or the algae is so extensive that you

TREATING POOLS WITH BANISH TO REMOVE ALGAE

cannot see the bottom in areas of the pool where

the water is 3 to 4 feet deep, use PowerFloc. Be

sure to follow the label directions on PowerFloc.

After completing the final step of the PowerFloc

usage – vacuuming to waste – proceed to step

two.

STEP TWO: Vacuum away any debris in the

pool. Thoroughly brush all pool surfaces with a

surface compatible brush.

STEP THREE: With the pump and filter

operating, apply one (1) pound of Burn Out Ex-

treme per 7,000 gallons of pool water or one (1)

pound of Burn Out 35 per 6,000 gallons of pool

water. Be sure to brush any undissolved product

off any bleachable surfaces.

STEP FOUR: Continue to operate pump and

filter for one hour.

STEP FIVE: With pump and filter operating,

apply sixteen (16) ounces of Banish per 10,000

gallons of pool water, pouring the product directly

into the pool in the areas of heaviest algae

growth.

STEP SIX: Keep the pump and filter operating

continuously for the next 24 hours.

STEP SEVEN: After 24 hours, thoroughly

brush all pool surfaces.

STEP EIGHT: Continue to operate the pump

and filter continuously for the next 24 hours.

Copyright ©2006 ULTRA MODERN POOL & PATIO, INC.

_____________________________________ NOTE: Always follow label directions and manufacturer’s instructions for

each product used. Conditions may vary from pool to pool. Ultra Modern

Pool & Patio does not assume any responsibility or liability for the results

that may be obtained through utilization of this or any other program,

procedure or product.

SPECIAL INSTRUCTIONS:

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

______________________________________

Page 2: TREATING POOLS WITH BANISH TO REMOVE ALGAE...TREATING POOLS WITH BANISH TO REMOVE ALGAE cannot see the bottom in areas of the pool where the water is 3 to 4 feet deep, use PowerFloc.

TREATING POOLS

WITH BANISH TO

REMOVE ALGAE

#119

VISIT

ULTRA MODERN POOL & PATIO

ON THE WORLD WIDE WEB AT www.ultramodern.com

E-MAIL: [email protected] FAX: 316-722-5643

OR CALL: 1-800-888-5872

JULY—2007

DID YOU KNOW? Ultra Modern Offers

Expert Repair Service!

Professional pool cleaning

Acid washing-Tile work

Spa equip. and supplies

Pool covers (safety & solar)

Resurface pool interior

Prompt-courteous service

Pool surveys

Heaters and pumps

Filters

Automatic pool cleaners

Complete pool repairs

Leak detection

Equipment repair on most makes & models

Call 722-4311 “Professionals for Professional Service”

Ultra Modern Pool & Patio

www.ultramodern.com

8100 W. Kellogg Wichita, KS 67209

316-722-4308 Toll Free: 800-888-5872

E-mail: [email protected]

5620 E. Kellogg

Wichita, KS 67218 316-681-3011

Toll Free: 866-258-5872 E-mail: [email protected]

1420 Nelson Dr. Derby, KS 67037

316-788-1122 E-mail: [email protected]

JOIN

ULTRA MODERN

POOL & PATIO’S

ULTRA

REWARDS

CLUB GET 1 POINT FOR EVERY DOLLAR SPENT, EVERY 100

POINTS RECEIVE A $5 CREDIT ON ACCOUNT CREDITS EXPIRE AFTER 90 DAYS

SEE STORE FOR DETAILS

*NOT APPLICABLE TOWARDS POOLS, SPAS, CLEARANCE OR “SPECIAL SALE” ITEMS,

SERVICE, LABOR, INSTALLATION OR DELIVERY COST.