Transport Layer3-1 Chapter 4: Network Layer r 4. 1 Introduction r 4.2 Virtual circuit and datagram...

Transport Layer 3-1

Chapter 4: Network Layer

4. 1 Introduction 4.2 Virtual circuit

and datagram networks

4.3 What’s inside a router

4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6

4.5 Routing algorithms Link state Distance Vector Hierarchical routing

4.6 Routing in the Internet RIP OSPF BGP

4.7 Broadcast and multicast routing

Transport Layer 3-2

A

B

G

DE

c

F

A

B

G

DE

c

F

(a) Broadcast initiated at A (b) Broadcast initiated at D

Transport Layer 3-3

A

B

G

DE

c

F1

2

3

4

5

(a) Stepwise construction of spanning tree

A

B

G

DE

c

F

(b) Constructed spanning tree

Multicast Routing: Problem StatementGoal: find a tree (or trees) connecting

routers having local mcast group members tree: not all paths between routers used source-based: different tree from each sender to rcvrs shared-tree: same tree used by all group members

Shared tree Source-based trees

Transport Layer 3-5









Transport Layer 3-6

The Internet Network layer

forwardingtable

Host, router network layer functions:

Routing protocols•path selection•RIP, OSPF, BGP

IP protocol•addressing conventions•datagram format•packet handling conventions

ICMP protocol•error reporting•router “signaling”

Transport layer: TCP, UDP

Link layer

physical layer

Networklayer

Transport Layer 3-7









Transport Layer 3-8

IP datagram format

ver length

32 bits

data (variable length,typically a TCP

or UDP segment)

16-bit identifier

Internet checksum

time tolive

32 bit source IP address

IP protocol versionnumber

header length (bytes)

max numberremaining hops

(decremented at each router)

forfragmentation/reassembly

total datagramlength (bytes)

upper layer protocolto deliver payload to

head.len

type ofservice

“type” of data flgsfragment

offsetupper layer

32 bit destination IP address

Options (if any) E.g. timestamp,record routetaken, specifylist of routers to visit.

how much overhead with TCP?

20 bytes of TCP 20 bytes of IP = 40 bytes + app

layer overhead

Transport Layer 3-9

IP Fragmentation & Reassembly network links have MTU

(max.transfer size) - largest possible link-level frame. different link types,

different MTUs large IP datagram divided

(“fragmented”) within net one datagram becomes

several datagrams “reassembled” only at

final destination IP header bits used to

identify, order related fragments

fragmentation: in: one large datagramout: 3 smaller datagrams

reassembly

Transport Layer 3-10

IP addresses: how to get one?

Q: How does host get IP address?

hard-coded by system admin in a file Wintel: control-panel->network->configuration->tcp/ip-

>properties UNIX: /etc/rc.config

DHCP: Dynamic Host Configuration Protocol: dynamically get address from as server “plug-and-play”


IP addressing: the last word...

Q: How does an ISP get block of addresses?

A: ICANN: Internet Corporation for Assigned

Names and Numbers allocates addresses manages DNS assigns domain names, resolves disputes


NAT: Network Address Translation

10.0.0.1

10.0.0.2

10.0.0.3

10.0.0.4

138.76.29.7

local network(e.g., home network)

10.0.0/24

rest ofInternet

Datagrams with source or destination in this networkhave 10.0.0/24 address for

source, destination (as usual)

All datagrams leaving localnetwork have same single source

NAT IP address: 138.76.29.7,different source port numbers



Motivation: local network uses just one IP address as far as outside word is concerned: no need to be allocated range of addresses from

ISP: - just one IP address is used for all devices can change addresses of devices in local network

without notifying outside world can change ISP without changing addresses of

devices in local network devices inside local net not explicitly

addressable, visible by outside world (a security plus).



Implementation: NAT router must:

outgoing datagrams: replace (source IP address, port #) of every outgoing datagram to (NAT IP address, new port #). . . remote clients/servers will respond using (NAT IP

address, new port #) as destination addr.

remember (in NAT translation table) every (source IP address, port #) to (NAT IP address, new port #) translation pair

incoming datagrams: replace (NAT IP address, new port #) in dest fields of every incoming datagram with corresponding (source IP address, port #) stored in NAT table



10.0.0.1

10.0.0.2

10.0.0.3

S: 10.0.0.1, 3345D: 128.119.40.186, 80

1

10.0.0.4

138.76.29.7

1: host 10.0.0.1 sends datagram to 128.119.40, 80

NAT translation tableWAN side addr LAN side addr

138.76.29.7, 5001 10.0.0.1, 3345…… ……

S: 128.119.40.186, 80 D: 10.0.0.1, 3345

4

S: 138.76.29.7, 5001D: 128.119.40.186, 80

2

2: NAT routerchanges datagramsource addr from10.0.0.1, 3345 to138.76.29.7, 5001,updates table

S: 128.119.40.186, 80 D: 138.76.29.7, 5001

3

3: Reply arrives dest. address: 138.76.29.7, 5001

4: NAT routerchanges datagramdest addr from138.76.29.7, 5001 to 10.0.0.1, 3345


ICMP: Internet Control Message Protocol

used by hosts & routers to communicate network-level information error reporting:

unreachable host, network, port, protocol

echo request/reply (used by ping)

network-layer “above” IP: ICMP msgs carried in IP

datagrams ICMP message: type, code

plus first 8 bytes of IP datagram

Type Code description0 0 echo reply (ping)3 0 dest. network unreachable3 1 dest host unreachable3 2 dest protocol unreachable3 3 dest port unreachable3 6 dest network unknown3 7 dest host unknown4 0 source quench (congestion control - not used)8 0 echo request (ping)9 0 route advertisement10 0 router discovery11 0 TTL expired12 0 bad IP header


IPv6 Initial motivation: 32-bit address space

soon to be completely allocated. Additional motivation:

header format helps speed processing/forwarding

header changes to facilitate QoS IPv6 datagram format: fixed-length 40 byte header


Transition From IPv4 To IPv6

Not all routers can be upgraded simultaneous How will the network operate with mixed IPv4

and IPv6 routers? Tunneling: IPv6 carried as payload in IPv4

datagram among IPv4 routers


TunnelingA B E F

IPv6 IPv6 IPv6 IPv6

tunnelLogical view:

Physical view:A B E F

IPv6 IPv6 IPv6 IPv6

C D

IPv4 IPv4

Flow: XSrc: ADest: F

data


data


data

Src:BDest: E


data

Src:BDest: E

A-to-B:IPv6

E-to-F:IPv6

B-to-C:IPv6 inside

IPv4

B-to-C:IPv6 inside

IPv4

Transport Layer3-1 Chapter 4: Network Layer r 4. 1 Introduction r 4.2 Virtual circuit and datagram...

Documents

Transcript of Transport Layer3-1 Chapter 4: Network Layer r 4. 1 Introduction r 4.2 Virtual circuit and datagram...