Trane WeatherGuard Kit Installer Guide - Airstar Supply · 2019. 6. 13. · 2 General Data This...
Transcript of Trane WeatherGuard Kit Installer Guide - Airstar Supply · 2019. 6. 13. · 2 General Data This...
SSAAFFEETTYY WWAARRNNIINNGGOnly qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, andair-conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or alteredequipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in theliterature and on the tags, stickers, and labels that are attached to the equipment.
BAYTWGR0004BAYTWGR0003BAYAWGR0004BAYAWGR0003
NNOOTTEE:: “Graphics in this document are for representationonly. Actual model may differ in appearance.”
Installer’s Guide
1188--HHHH332DD11-- --EENN
Plastic Top Aftermarket Kit
March 2019 11BB
2
General Data
This accessory kit is intended for use on Trane orAmerican Standard units that are purchased without aplastic top. The accessory assembles on top of the unit.No parts, e.g. sheet metal top or fan grille, should beremoved from unit before installation of kit.
KKiitt CCoonntteennttss::
IInnssppeeccttiioonn::
Check carefully for any shipping damage. This must bereported to and claims made against the transportationcompany immediately. Any missing parts should bereported to your supplier at once and replaced withauthorized parts only.
18-HH32D1-1B-EN
3
Figure 1. Foam Gasket Location
Foam Gasket Location
Figure 2. Adapter Ring Tabs
Adapter Ring
Tab
Control Box Corner
GGeenneerraall DDaattaa
18-HH32D1-1B-EN
IInnssttaallllaattiioonn IInnssttrruuccttiioonnss::
Figure 3. Small Support Clips Installation
Small Support Clips (x3)
Control Box Corner
Figure 4. Small Support Clips Alignment
Groove
Indentation
Small Support Clip
GGeenneerraall DDaattaa
418-HH32D1-1B-EN
5
Figure 5. Large Support Clip Position
AlignmentTab
Large Support Clip
Figure 6. Plastic Top Installation
Screws (4x)
Plastic Top
GGeenneerraall DDaattaa
18-HH32D1-1B-EN
6
RReemmoovvaall IInnssttrruuccttiioonnss::
ry from the top thead
ry until the adapter ring is free
from
Figure 7. Removal Instructions
Arrow Marks (2x)
GGeenneerraall DDaattaa
18-HH32D1-1B-EN
RReeccoommmmeennddeedd CClleeaarraanncceess::
Figure 8. Recommended Clearances for the Unit
Min. 12” to Shrubbery
Near Bedrooms
Min 5’ Unrestricted
Access Panel
Min 3’ Unrestricted
3’
3’
GGeenneerraall DDaattaa
18-HH32D1-1B-EN7
Ingersoll Rand (NYSE: IR) advances the quality of life by creating comfortable, sustainable and efficientenvironments. Our people and our family of brands— including Club Car®, Ingersoll Rand®, Thermo King® andTrane®—work together to enhance the quality and comfort of air in homes and buildings; transport and protectfood and perishables; and increase industrial productivity and efficiency. We are a global business committed to aworld of sustainable progress and enduring results.
ingersollrand.com
Ingersoll Rand has a policy of continuous product and product data improvements and reserves the right to change design and specificationswithout notice.We are committed to using environmentally conscious print practices.
18-HH32D1-1B-EN 12 Mar 2019Supersedes 18-HH32D1-1A-EN (February 2019) ©2019 Ingersoll Rand