Tracker and Jammer
Transcript of Tracker and Jammer
-
8/7/2019 Tracker and Jammer
1/16
In GSM tracker system ,the cell informationprovided by each cell of the GSM network istaken from the mobile device and converted
into the form of an SMS which is sent back tothe master system. The master systemidentifies the cell and locates the vehicle.
JAMMING is the act of intentionally directingelectromagnetic energy at a communicationsystem to disrupt or prevent signaltransmission.
-
8/7/2019 Tracker and Jammer
2/16
-
8/7/2019 Tracker and Jammer
3/16
GPS Global Positioning System Allow GPS receiver to determine its exact POSITION in
longitude and latitude, velocity, direction etc.
GSM Global System of Mobile Allow this POSITION information to be sent to central
control room as SMS or GSM data call
GPRS General Packet Radio Service Allow transfer of multimedia content like photograph
to central control room or other mobile unit
-
8/7/2019 Tracker and Jammer
4/16
GSM is required in Vehicle tracking systems because GPS
system can normally only receive location information
from satellites but cannot communicate back with them.Hence we need some other communication system like
GSM to send this location information to central control
room.
Other technologies can also be used but they are more
costly
-
8/7/2019 Tracker and Jammer
5/16
Tracker
LBS (Location based services)
Push Based
Pull BasedApplication
-
8/7/2019 Tracker and Jammer
6/16
Communicating With GSM Modem
Using Software (NetMonHR)
-
8/7/2019 Tracker and Jammer
7/16
Getting data from Microcontroller
Separating Cell ID and LAC
Finding out methods to map on
google map
Navigation
-
8/7/2019 Tracker and Jammer
8/16
1. TRANSMITTER:
Interconnect
network 89V51
MAX-232
LCD
Display
-
8/7/2019 Tracker and Jammer
9/16
2. RECEIVER:
Interconnect
network89V51
PC
Interface
IC 4050
-
8/7/2019 Tracker and Jammer
10/16
-
8/7/2019 Tracker and Jammer
11/16
The frequency of the transmitted signal of thejammer must cover the GSM frequency range
As the power received from the GSM Base Station isusually low, It is easier to jamm the downlink (i.e.Jamming the mobile station 'handset' receiver) thanuplink, hence the jammer output frequency shouldcover the downlink frequency.
UPLINK DOWNLINK
GSM 900 890 915 MHz 935 960 MHz
-
8/7/2019 Tracker and Jammer
12/16
PowerSupply
3.5,5,
12,-
12V
IFSection
RFSection
-
8/7/2019 Tracker and Jammer
13/16
RF section is the most important part ofthe jammer.
It consists of VCO,RF power amplifier andantenna.
These components were selectedaccording to the specification of the
jammer such as frequency range andcoverage.
-
8/7/2019 Tracker and Jammer
14/16
The function of the IF-section of the Mobile jammer is
to generate the tuning signal required by the VCO in
the RF-Section.
The main parts of the IF-Section are:
Triangular Wave Generator
Noise Generator
Signal Mixer and DC offset
-
8/7/2019 Tracker and Jammer
15/16
The Jammer designed to take its power
from the regular 220V AC wall outlets.
The IF & RF sections of the jammerrequire +3.5, 5, +12, and -12 DC Voltages.
Transformer Rectifier Filter
+ Regulator
+12V
+ Regulator
+5V
- Regulator
- 12V
-
8/7/2019 Tracker and Jammer
16/16
Jammer can be use in the followingplaces:
Conference room
Temples and Mosques
Government offices
Libraries