TOYOTA 4RUNNER ‘10-‘20 and TACOMA ‘05-’20 · 12/4/2019 · Toyota 4Runner System Shown...
Transcript of TOYOTA 4RUNNER ‘10-‘20 and TACOMA ‘05-’20 · 12/4/2019 · Toyota 4Runner System Shown...
INSTALL GUIDE
TOYOTA 4RUNNER ‘10-‘20 and TACOMA ‘05-’20
PATENT
PENDING
Included in Kit• One (1) Custom 4Runner / Tacoma Switch Housing • Switches of Your Choice• One (1) Power Control Module Box & Cover• One Custom Plug and Play Wiring Harness• One (1) Custom Powder Coated Bracket• One Fuse Tap• Eight (8) Nylon HD Cable Ties 50# Tensile 7" Black • Two (2) 1/4-20 x 3/4" Hex Cap Screw s • Two (2) 1/4-20 Nyloc Nuts• Two (2) 6-32x3/4 Black Hex Set Screws• Two (2) 6-32 304 Stainless Hex Keps Lock Nuts• Instructions and Link to Installation Video • Made in the USA Sticker• Team Tech Offroad Sticker • S-TECH Switch Systems Sticker
Toyota 4Runner System Shown
Inset:
Tacoma ‘05-’15 6 Switch System
DEVELOPED, DESIGNED, MANUFACTURED and Assembled in the Rocky Mountains of Colorado, known to many as OFFROAD COUNTRY. Trail riding at 10,000 feet at night requires great lighting and a well-engineered switch system. That is where S-TECH was developed and tested. Simple solutions to Off-Road challenges results in reliability, safety and convenience. Our Made in the USA injection molded switch housing and plug and
play wire harness has a pure OEM look and feel second to none. Please take a moment to read the following instructions and procedures. Since you will be drilling and cutting into parts of your vehicle, we highly suggest that you consider using either a service professional or use professional techniques and practices while installing your S-TECH Switch System.
Please be sure to check our website stechswitch.com/installs-new/
for the latest INSTALLATION UPDATES. Any questions please contact us at 720.307.7263
S-TECH Switch Systems™
** Before starting the installation process, disconnect the vehicles' primary battery ground
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
2
01
IDENTIFY WIRE LEADS:Familiarize yourself with all of the wire circuits.
Please check our website, www.STechSwitch.com/Installs-new for the latest in installation updates and helpful hints to your installation.
Position Color 1 Yellow 2 Orange 3 Brown 4 Grey
4 SWITCH SYSTEM
WIRE IDA = Output Wires 1, 2, 3, 4 (5, 6)B = Small Accessory Red Wire (Fuse Block, connect to Fuse tab and insert in Fuse Block Position M9C = Big Red Wire (12V Battery)D = Black Wire (Ground)
A
B
D
C
Position Color 1 White 2 Green 3 Yellow 4 Orange 5 Brown 6 Grey
6 SWITCH SYSTEM
FROM YOUR ACCESSORIES:Only connect the positive side to the STECH OUTPUTS. By design, each of your accessories should be grounded at or near each accessory.
6 switch system output wires
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
3
Push the black switch harness and red accessory
wire through the boot and into the passenger
compartment. If you are having a tough time take some electrical tape and
wrap to conceal the sharp connector edges. Spray
with lubricant to make it easier to go through
the boot.
Open the S-TECH box and familiarize yourself with all of the parts that you will be using during the
install.02
Start in the Engine bay and lay the S-TECH Module on top of the engine cover so
we can start laying out our lines. Find the 6-Pin Black
Connector that goes into the switch panel
with the red accessory switched power wire.03
Make a small slit about 1/2” wide in the boot going through the fire
wall. Start in the middle to the left of the factory engine harness and
cut away from the harness as to not pierce the factory lines. Then
stick your finger in the slit and feel for the second side of the boot by
the factory harness so you can feel where you wire
pops through inside the passenger compartment.04
05
Disconnect the negative battery terminal before starting.
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
4
REMEMBER: Be a Pro!Always measure twice and cut once.
Remove any applied tape. Pull a bit of
excess through about a foot and a
half or so will do.06
07
If you haven’t already, it’s time to decide which side you want the unit on. The
bracket provided by S-TECH allows for both passenger
and driver side. In my case I chose the driver side until I
decide the remaining layout of my engine bay.
Grab your bracket and bolts with the fixed washer and
bolt them down about half-way so you can adjust its
position in the next step of the install.
Attach bracket with the flanged bolts
using these holes.
Tighten up the bracket so it matches the slant of the hood for aesthetics. A
ratcheting wrench works wonders here.08
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
5
Grab the unit and the remaining 2 bolts and
nuts, and attach the unit to the bracket. Now
its time to make your connections. 10
Secure unit to the bracket
using the remaining 2 nuts
& bolts.
Before bolting the Module to the bracket let’s run our
ground and power cables in a nice clean location behind
the factory fuse block alongside the inner fender.
Go ahead and install the ground directly to the
battery or body ground as this in not a high
amp ground.09
4Runner Tacoma
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
6
BE SURE TO INSTALL THE CORRECT FUSE FOR YOUR ACCESSORY.
Install the fuse with the accessory manufacturers’ recommendation on the amperage of each fuse location. Make sure it matches with the fuse location in S-TECH. Maximum Total Load 600 watts / at 12V, 72 amps. All circuits are capable of 30A each.
Example: A 50" light bar would require a 30A fuse while a few LED rock lights would usually require less than 10A
4 position switch system shown11
Fuse 1
Fuse 2
Fuse 3
Fuse 4
Relay 4
Relay 2
Relay 3
Relay 1
Here's how the switch numbers relates to fuses and relays.
6 position switch system shown11b
Fuse 3
Fuse 4
Fuse 5
Fuse 1
Fuse 2
Fuse 6
Relay 4Relay 5
Relay 2Relay 6
Relay 3
Relay 1
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
7
4Runner: Next pull the side caps off that surround the fan and
temperature control knobs. To remove these just grab the bottom
with one hand and give a gentle squeeze, then put your other hand
up top and grab the back of the trim and pull firmly straight back
towards the center console.
Tacoma: Remove drink holder by prying out and lifting. Remove (4)
Philips screws on the front and rear console pieces.
4Runner: Once those are off, un-screw the two Philips that hold the HVAC Panel on and unplug
the wires and store panel in a safe place, so as to not damage it. Once unbolted, slide a panel popper
between the pocket and HVAC panel and twist the tool to pop the panel off. This does take a little
bit of force and there are four clips, so keep it as square as possible as to not damage anything.
Tacoma: Remove the cover in the bottom of the storage console by lifting one edge revealing (2) 10mm screws in the
bottom of the storage area. Lift the rear of the storage unit up and pull back to remove this section of the center console. You may need to separate the front and rear section by lifting
the front. Remove the shifter knob for manual transmission models. Lift up on the rear of the front section of the console
over the shifter to remove this section. You will now have access to the installation area for the switch assembly.
14
13
4Runner
4Runner
Tacoma
Tacoma
12
Optional 60 Amp Breaker- NOTE: The breaker is marked for the
correct connection on that side. Take your positive lead from the
unit and bolt attach it to the AUX side. Then take the lead from the battery and connect it to the BAT side. Once thats done find a place to mount it. I placed it on the side
of the engine with a screw through a pre-existing hole.
Connect the red terminal wire from the unit to the side stamped AUX
Connect this side to the
battery
Run the wire from this connection to the positive terminal on the
battery
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
8
Next take your provided template and set it flush
against the bottom of the rear cubby portion. Take your 1/8” Drill bit and drill 2 holes in the spots indicated by the template on the sides.17
S-TECH 6: First, disassemble and remove
the storage area below the head unit. Drill a
3/4” hole in the lower tray on the left side of
tray as that is where the wires are linked together.
Remove any burrs to avoid the risk of a wire
getting cut.15
Position flush against the back
Drill here using the 1/8” bit
Now take your switches and housing and feed
the rear connector through the hole in
the rear. NOTE: before inserting it remember to
remove the stickers on the side of the housing
covering the holes.18
Push connector through the hole you made in the back of
the tray
Remove sticker and slide housing into the tray
16
S-TECH 4: 4Runner only. Not required on Tacoma. Now you
will need to pop the USB plug and power outlet out of the pocket
piece so we can drill our holes for the switch panel. USB is easy and
will push right out. The power outlet needs to come out in two
pieces. First step is to pry the one plastic tab away from the metal
body of the outlet and then slide the metal sleeve out. Once the
metal sleeve is out, compress the 2 plastic ears into the plastic
tube so you can push that out of the panel.
S-TECH 6 HOLE HERE
S-TECH 4 HOLE HERE
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
9
Your housing should sit perfectly flush.
Reinstall console in reverse order.21
Reassemble the lower dash piece with your
power outlet and USB plug and reinstall
into the vehicle. Now reinstall the rest of the
center console and dash back to factory.20
Push the housing all the way in and the
holes should line up perfectly. Screw in the 2 small black screws.
Go ahead and fully reassemble the tray
and shifter area back into the area. You
can easily connect to the switches later by removing the trim
piece on the driver side of the tray.19
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
10
Be sure to note the direction of the fuse tap relative to the Power Distribution Box. Failure to install the FUSE TAP in the correct direction
will result in NO POWER to the system. Use the supplied Fuse Tap to provide for an “ignition on only” 12V source. CONNECT Fuse Tap
to accessory on only location. This will enable the system when the ignition is turned on. Do not install the red accessory wire directly to a
12 volt source like a live fuse or the vehicles 12V battery as this will drain your battery since the lower LED lights will be on all the time.
Some customers have chose not to use to fuse tap and have installed a secondary switch (see inset photo) to the RED Accessory
wire circuit to turn it On/Off manually without the ignition on. However be very careful not to leave it on too long,
it will drain our battery.24
secondary switch* *Optional secondary switch available on www.stechswitch.com/accessories
Now that we have our wires plumbed
where they need to go, securely fasten them
up out of the foot well and away from any
moving parts.23
Now it is time to connect the red accessory wire to our included fuse tap to a key on circuit. For
4Runner: Pull the fuse cover on the driver’s side kick panel area and
take a look at the cover and find the blank slot indicated in photo.
Tacoma: Remove the “pull-out” panel on the lower dash revealing
the fuse panel. Look for the ACC fuse,
a 7.5 AMP fuse.
22
4Runner Tacoma
Original Location
NEW Location
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
11
27
26
Once done connecting your loads tuck the
wires under the box for a nice professional look.
As you add accessories be sure to install the correct fuse for each
accessory.
25
Now before we connect it to the Positive
terminal on the battery, remove the fuses as
you will only need them as you install
your different loads to ensure no accidental
short circuits. Once this is done connect the
main power line to the battery.
Be sure to install the correct fuse for each of
your accessories.
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
12
28
Connect your battery, take a seat and turn on your ignition and
if you did things correctly you’ll
be greeted by the illumination of the
switches!
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
13
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
14
To Ground
To Ground
60 AMP Breaker*
24" or 60" Battery Cable
Ground
Output Connections
Adjustable Low Voltage Disconnect*
To Switch Housing
Accessory Wire To Fuse Tap or 12 Volt Source To Battery
See “Direction to Adjust Voltage”in the Installation Updates
Shown with Optional Adjustable Low Voltage Disconnect & 60 AMP Breaker
We highly recommend the use of a 60AMP Breaker with all of our switch systems! Protect your battery from low voltage with one of our Low Voltage Disconnect options.
To Battery24” or 60” Battery Cable
Ground
Output Connections
To Switch Housing
Accessory Wire (to fuse tap)
Breaker Waterproof BreakerAlso Available: Breaker with 24” or 60" Battery CableVisit us online for more infoA
B CCap only fits when
the cables are inline with the screw holes.
Battery Cable Extension OptionsDepending on your order, we may have included a battery cable extension post (A) to
accommodate the cable length required for your vehicle. For install / use info, visit www.stechswitch.com/installs-new/#installationupdatespage
We highly recommend the use of a 60AMP Breaker with all of our switch systems! Your choice of “Regular” (B) or Waterproof (C).
*Optional
SWITCHES LEFT TO RIGHT: Switch Position 1, 2, 3, 4, (5, 6 only with 6 position)
4Runner shown with 4 and 6 switch systems installed.
[email protected] • 25587 Conifer Rd. | #105-220 | Conifer, CO 80433 | 720-307-7263
S T E C H S W I T C H . C O M
15
NOTE:If switches are inoperable recheck ground, 12V source and red ignition source for power.
Should you have troubleshooting questions check the S-TECH website stechswitch.com/installs-new/ or call us at 720-307-7263.
For information & videos as well as printable / downloadable instructions and templates, please visit
www.STECHSWITCH.com
CONGRATULATIONS! You have just completed the installation of your new
S-TECH SWITCH SYSTEM.Any Questions or Comments please call
720-307-7263or email us at
Other Vehicle Housing Solutions Available at:stechswitch.com/accessories
Toyota Tacoma Toyota 4 Runner
Jeep JL Jeep JK
Chevy ColoradoDodge RAM