torque .ppt

26
L-10 Torque and Rotational Motion Torque makes things spin!

description

angular momentum , moment of inertia and torque

Transcript of torque .ppt

Page 1: torque .ppt

L-10 Torque and RotationalMotion

Torque makes things spin!

Page 2: torque .ppt

What makes something rotate in the first place?

TORQUE

AXEL

How do I apply a force to make the rod rotateabout the axel? Not just anywhere!

Page 3: torque .ppt

TORQUE

• To make an object rotate, a force must be applied in the right place.

• the combination of force and point of application is called TORQUE

Force, F

lever arm, L

Axle

Page 4: torque .ppt

Torque = force times lever arm

Torque = F L

Page 5: torque .ppt

Torque example

F

L

What is the torque on a boltapplied with a wrench that has a lever arm of 30 cmwith a force of 10 N?

Torque = F L = 30 N 0.30 m = 9 N m

For the same force, you get more torquewith a bigger wrench the job is easier!

Page 6: torque .ppt

Homer attempts to straighten out the leaning tower of Pisa

folcrum

lever

Page 7: torque .ppt

Net Force = 0 , Net Torque ≠ 0

10 N

10 N

• > The net force = 0, since the forces are applied in opposite directions so it will not accelerate.

• > However, together these forces will make the rod rotate in the clockwise direction.

Page 8: torque .ppt

Net torque = 0, net force ≠ 0

The rod will accelerate upward under thesetwo forces, but will not rotate.

Page 9: torque .ppt

Balancing torques

10 N20 N

1 m 0.5 m

Left torque = 10 N x 1 m = 10 n mRight torque = 20 N x 0.5 m = 10 N m

Page 10: torque .ppt

Equilibrium

• To ensure that an object does not accelerate or rotate two conditions must be met:

net force = 0 net torque = 0 • this results in the

practical 4-1 “ladder rule”

Page 11: torque .ppt

When is an object stable?

• If you can tip it over a bit and it doesn’t fall

• The object may wobble a bit but it eventually stops and settles down to its upright position.

Page 12: torque .ppt

Why things fall over• Every object has a special point called the

center of gravity (CG). The CG is usually right smack in the center of the object.

• if the center of gravity is supported, the object will not fall over.

• You generally want a running back with a low CG then it’s harder to knock him down.

• The lower the CG the more stable an object is. stable not easy to knock over!

Page 13: torque .ppt

Condition for stability

If the CG is above the edge, the objectwill not fall

CG

Page 14: torque .ppt

when does it fall over?

CG CG

STABLE NOT STABLE

If the vertical lineextending down fromthe CG is inside theedge the object willreturn to its uprightposition the torquedue to gravity bringsit back.

Page 15: torque .ppt

Stable and Unstable

stable unstable

torque due to gravitypulls object back

torque due to gravitypulls object down

Page 16: torque .ppt

Stable structures

Structures arewider at their

base to lower theircenter of gravity

Page 17: torque .ppt

If the center of gravityis supported, the blocksdo not fall over

Playing with your blocks

CG

Page 18: torque .ppt

Object with low CG

Stay low to the ground!

300 lb fullback who is4 ft, 10 inches talland runs a 4-40

Page 19: torque .ppt

As more and more stuff is loaded into asemi, its center of gravity moves upward.It could be susceptible to tipping over.

High ProfileVehicles

wind

Page 20: torque .ppt

The shape of an object determines how easy or hard it is to spin

For objects of the same mass, the longerone is tougher to spin takes more torque

Hinge

Page 21: torque .ppt

It matters where the hinge is

The stick with the hinge at the end takes 4 timesmore torque to get it spinning than the stick withthe hinge in the center.

Page 22: torque .ppt

Rotational Inertia (moment of inertia)

• Rotational inertia is a parameter that is used to quantify how much torque it takes to get a particular object rotating

• it depends not only on the mass of the object, but where the mass is relative to the hinge or axis of rotation

• the rotational inertia is bigger, if more mass is located farther from the axis.

Page 23: torque .ppt

How fast does it spin?

• For spinning or rotational motion, the rotational inertia of an object plays the same role as ordinary mass for simple motion

• For a given amount of torque applied to an object, its rotational inertia determines its rotational acceleration the smaller the rotational inertia, the bigger the rotational acceleration

Page 24: torque .ppt

Big rotationalinertia

Small rotationalinertia

Same torque,different

rotational inertia

spinsslow

spinsfast

Page 25: torque .ppt

rotational inertia - examples

Suppose we have a rod of mass 2 kg and length1 meter with the axis through the center

Its moment of inertia is 2 units

Imagine now that we take the same rod and stretch it out to 2 meters; its mass is, of course,the same.

Its moment of inertia is 4 units

Page 26: torque .ppt

rotational inertia examples

Rods of equal mass and length

axes through center

axes through end

Rotational inertia of 1 unit

Rotational inertia of 4 units