Tools and machines - technolit.de · Manual tools Drilling, cutting, milling Saws Power tools...
Transcript of Tools and machines - technolit.de · Manual tools Drilling, cutting, milling Saws Power tools...
Manual tools
Drilling, cutting, milling
Saws
Power tools
Sorting systems, mounting
Electronic accessories
Pressurized air tools and accessories
Car special
Tools and machines
Drilling, cutting, millingMetal drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 931 – 941
Taper/deburring/countersink . . . . . . . . . . . . . . . . . . . . . . . . . . 942 – 943
Level drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 944
Quick helix drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 945
Thread cutting tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 946 – 953
Hard metal cutting pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954 – 959
Weld point drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 960 – 963
Stone drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 964 – 968
Core hole drill assortment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969 – 975
Our entire assortment of drills
Machine tap – HSS-G DIN 731 Twist drill – HSS DIN 338 black
Machine tap – TIN DIN 371 Twist drill – HSS DIN 338 polished
Twist drill – HSS DIN 340 polished
Twist drill – SAS-P W-HSS DIN 338Hand tap – DIN 2181
Hand tap – HSS-G DIN 352
Counterbore – DIN 373 HSS
Masonry drill – SDS-Plus
Masonry drill – SDS-Max
Stone and concrete hammer
Twist drill with offset shaft – Type N DIN 338
Morse taper drill - Type N DIN 345
Taper and deburring counterbore – HSSG
Carbide burr – Plain
Carbide burr for alu – Cylinder-shaped
Sheet metal cone bit – HSSG
Universal step drill – HSS
Spot weld cutter – HFB
Spot weld cutter – HFB
Spot weld cutter – HSS-E polished
Spot weld cutter – HSS-E TIN
Spot weld cutter – HSS-E polished
Turbo milling drill
Twist drill – SAS-Plus C-HSS
Double-ended drill – HSS
Spot weld cutter – HSS-E TIN
Solid carbide three-side cutter – HFB
SDS-Max chisel
SDS-Plus chisel
DieHSS DIN 223
Tools and machines | 930
THE WORK SHOP EXPERTDrilling, cutting, milling
TK7105
Our entire assortment of drills Drilling with new tip geometry
Hand drill with centring crown• Particularly suitable for
hand drilling with cordless screwdrivers
• Developed for drilling through metal tubes and thin sheet metal
• In combination with cutting paste also suitable for drilling through stainless steel
• Excellent drilling results also in soft materials such as acrylic glass, other plastics and wood
Art No. Description Model Contents Size ø703 502 Hand drill with centring crown 25 pcs . 1,0 – 13,0 mm
Art No. Description Model Size ø Unit703 502 0100 Hand drill with centring crown 1,00 mm 10703 502 0150 Hand drill with centring crown 1,50 mm 10703 502 0200 Hand drill with centring crown 2,00 mm 10703 502 0250 Hand drill with centring crown 2,50 mm 10703 502 0300 Hand drill with centring crown 3,00 mm 10703 502 0350 Hand drill with centring crown 3,50 mm 10703 502 0400 Hand drill with centring crown 4,00 mm 10703 502 0450 Hand drill with centring crown 4,50 mm 10703 502 0500 Hand drill with centring crown 5,00 mm 10703 502 0550 Hand drill with centring crown 5,50 mm 10703 502 0600 Hand drill with centring crown 6,00 mm 10703 502 0650 Hand drill with centring crown 6,50 mm 10703 502 0700 Hand drill with centring crown 7,00 mm 10703 502 0750 Hand drill with centring crown 7,50 mm 5703 502 0800 Hand drill with centring crown 8,00 mm 5703 502 0850 Hand drill with centring crown 8,50 mm 5703 502 0900 Hand drill with centring crown 9,00 mm 5703 502 0950 Hand drill with centring crown 9,50 mm 5703 502 1000 Hand drill with centring crown 10,00 mm 5703 502 1050 Hand drill with centring crown 10,50 mm 1703 502 1100 Hand drill with centring crown 11,00 mm 1703 502 1150 Hand drill with centring crown 11,50 mm 1703 502 1200 Hand drill with centring crown 12,00 mm 1703 502 1250 Hand drill with centring crown 12,50 mm 1703 502 1300 Hand drill with centring crown 13,00 mm 1
… Metal
… Wood
… Stainless steel
… Plexiglas
… Thin plate
… Composite panels
Tools and machines | 931
THE WORK SHOP EXPERTMetal drill
TK7105
Drilling with new tip geometry
Hand drill with centring crown
Innovative 100° drill tip
Multi-cut drill head
Specially grinded 140° blades
Anti-slip shaft with three-face blade
• Direct, pinpoint drilling without punch-marking through precision cross-grinding for extremely precise centring and guiding
• No slipping, even on round surfaces, through innovative 100° drill tip with centring head
• No running-off and pre-drilling any more through reducing the cross-cutter
• Perfect centring and no slipping on surface through multi-cut drill head with 7 extremely wear-resistant blades
• Shear reinforcement for faster drilling progress, thus no „pushing“ into material required
• Circular, nearly burr-free holes even in thin material due to specially sharpened 140° blades
• Collets of drill chuck securely and tightly grip the grinded flanks
• No spinning any more
• No damaging of drill chuck
• Excellent power transmission
… with 7 blades
Three-face bladeForce-locking clamping Clamping surface
Tools and machines | 932
THE WORK SHOP EXPERTMetal drill
TK7105
Drilling with new tip geometry
Hand drill with centring crownPerfect chip removal
Engraved size marking
Reinforced core
M2 professional high-performance high-speed steel
Large torsion range
• Chip space from tip to shaft end tapered by 10%, thus reduced friction, perfect chip removal and clean material surface in drill hole
• Clearly legible marking of size, type and article no . even after use
• Increased toughness for up to 50% more breakage resistance and extremely long service life through reinforced drill core
• Excellent heat resistance
• Temperature stability even exceeding 500 °C
• Hardness 63 – 66 Rockwell HRC
… Clamped „standard drill“
. . . Hand drill
• Extended torsion range through defined clamping surface
• Increase of elasticity and breakage resistance through short but secure mounting shaft
short torsion range
large torsion range
… increased drilling depth
Tools and machines | 933
THE WORK SHOP EXPERTMetal drill
TK7105
Special metal drill SAS-Plus C-HSS• For extreme strain in industry and trade• Significantly improved lifetimes and increased
drilling performance
• For all steels, especially adequate for hard to chip and high heat resistant special steels (e . g . titan and titan alloy) as well as rust and acid resistant steels
Qualities:• Drill split point precision machined to 130° in accordance with DIN 1412 C for accurate
drilling and centering without center punch
• Less cutting force, more precise hole sizes, and better concentricity
• Wide grooves provide more room for chips, reduce friction and promote cutting power
• Winding grooves and cutting surfaces deep and wide for excellent distribution of cooling agent
• Hardened and tempered blank ground from solid material for greater endurance
• Cobalt alloy lends high material strengthfor maximum cutting and improved chip removal . Longer lifetime and less wear on the cutting edges
• Laser-scored information about size, quality, type, material and surface coating
Type/MaterialType/Material
SAS = High speed steel
Plus = Plus Precision cut
C = Cobalt alloy
HSS = High performance quick steel
Technical specifications:Point bevel: Split point in accordance with DIN 1412 C
Point thinning (DIN) point angle: 130°
Core thickness: normal/standard
Core increase: normal/standard
Helix flute (helix angle): 25° – 30°
Flute type: Type N
Ø Tolerance: h8
Areas of use:Materials• Alloy/non alloy steels up to 1200 N/mm²• High alloy steels• Titan and titan alloy• For steel and steel cast alloy • Grey cast iron, malleable steel,
spheroidal steel• Aluminium and aluminium alloy• Copper, bronze, brass, and other materials
Art No. Description Size703 100 Drill bit box 1,0 – 10,0 mm703 101 Drill bit box 1,0 – 13,0 mm
Art No. Size Unit703 501 0100 1,0 mm 10703 501 0150 1,5 mm 10703 501 0200 2,0 mm 10703 501 0250 2,5 mm 10703 501 0300 3,0 mm 10703 501 0310 3,1 mm 10703 501 0330 3,3 mm 10703 501 0350 3,5 mm 10703 501 0400 4,0 mm 10703 501 0410 4,1 mm 10703 501 0420 4,2 mm 10703 501 0450 4,5 mm 10703 501 0490 4,9 mm 10703 501 0500 5,0 mm 10703 501 0510 5,1 mm 10703 501 0520 5,2 mm 10703 501 0550 5,5 mm 10703 501 0600 6,0 mm 10703 501 0610 6,1 mm 10703 501 0650 6,5 mm 10703 501 0680 6,8 mm 10703 501 0700 7,0 mm 10703 501 0750 7,5 mm 10703 501 0800 8,0 mm 10703 501 0850 8,5 mm 10703 501 0900 9,0 mm 10703 501 0950 9,5 mm 10703 501 1000 10,0 mm 10703 501 1050 10,5 mm 10703 501 1100 11,0 mm 5703 501 1150 11,5 mm 5703 501 1200 12,0 mm 5703 501 1250 12,5 mm 5703 501 1300 13,0 mm 5
A classification system has never been so practical, robust and clear!
Plastic order system „Systor“• Equipped with 81 DIN 388 drill bits, SAS-Plus C-HSS 1 .0 mm – 10 .0 mm
Drill securely held by recesses in the cover
Drill bit tray made of rugged plastic ensures organization and clear arrangement of bits
Sticker with all drill bulk goods visible on
the cover
Extremely robust and impact resistant industrial plastic box
Art No. Description703 055 „Systor“ plastic classification system with SAS plus C-HSS
Tools and machines | 934
THE WORK SHOP EXPERTMetal drill
TK7105
Video
Special-metal drill SAS-P W-HSS• Wolfram alloyed drill
therefore long lifetime and adequate for many materials like steel, VA, but also soft materials like copper, alu etc .
• Spiral drill with precision cut and reduced cross cutting edge therefore centering during centre-drill and less exertion of force in advance
• Drill has alloy parts and no coating therefore constantly good quality and lifetime also after re-grinding
Qualities:• 118° ground tip
• With split point according to DIN 1412 C from ø 3 .0 mm
• Very good centering
• Long service life due to Wolfram alloy
• Adequate for many materials, e .g . for steel, VA, but also for soft materials like copper, aluminium, etc .
• Groove and cutting part with precision cut and reduced cross cutting edge
• Finely ground groove and cutting part made of one piece
• Good chip disposal
• Less force effort during advance
• Additionally high material hardness through Wolfram alloy
• Drill has alloy components and no coating, therefore consistent quality and lifetime also after grinding
• Lasered final marking over size, type, material and coating
Type/MaterialSAS = High speed steel
P = Precision cut
W = Wolfram alloyed
HSS = High Speed Steel
Art No. Description Size Contents Standard703 051 SAS-P W-HSS drill bit set 1,0 – 10,5 mm 170 pcs . DIN 338703 565 Special metal drill bit box 1,0 – 10,0 mm 19 pcs . 703 566 Special metal drill bit box 1,0 – 13,0 mm 25 pcs .
Tools and machines | 935
THE WORK SHOP EXPERTMetal drill
TK7105
Art. No.
ø m
m
unit
Overall length
mm
Chip flute length mm
Art. No.
ø m
m
unit
Overall length
mm
Chip flute length mm
Special-metal drill SAS-P W-HSS
Art. No.
ø m
m
unit
Overall length
mm
Chip flute length mm
703 540 0100 1,0 mm 10 34 mm 12 mm703 540 0110 1,1 mm 10 36 mm 14 mm703 540 0120 1,2 mm 10 38 mm 16 mm703 540 0130 1,3 mm 10 38 mm 16 mm703 540 0140 1,4 mm 10 40 mm 18 mm703 540 0150 1,5 mm 10 40 mm 18 mm703 540 0160 1,6 mm 10 43 mm 20 mm703 540 0170 1,7 mm 10 43 mm 20 mm703 540 0180 1,8 mm 10 46 mm 22 mm703 540 0190 1,9 mm 10 46 mm 22 mm703 540 0200 2,0 mm 10 49 mm 24 mm703 540 0210 2,1 mm 10 49 mm 24 mm703 540 0220 2,2 mm 10 53 mm 27 mm703 540 0225 2,25 mm 10 53 mm 27 mm703 540 0230 2,3 mm 10 53 mm 27 mm703 540 0240 2,4 mm 10 57 mm 30 mm703 540 0250 2,5 mm 10 57 mm 30 mm703 540 0260 2,6 mm 10 57 mm 30 mm703 540 0270 2,7 mm 10 61 mm 33 mm703 540 0275 2,75 mm 10 61 mm 33 mm703 540 0280 2,8 mm 10 61 mm 33 mm703 540 0290 2,9 mm 10 61 mm 33 mm703 540 0300 3,0 mm 10 61 mm 33 mm703 540 0310 3,1 mm 10 65 mm 36 mm703 540 0320 3,2 mm 10 65 mm 36 mm703 540 0325 3,25 mm 10 65 mm 36 mm703 540 0330 3,3 mm 10 65 mm 36 mm703 540 0340 3,4 mm 10 70 mm 39 mm703 540 0350 3,5 mm 10 70 mm 39 mm703 540 0360 3,6 mm 10 70 mm 39 mm703 540 0370 3,7 mm 10 70 mm 39 mm703 540 0375 3,75 mm 10 70 mm 39 mm703 540 0380 3,8 mm 10 75 mm 43 mm703 540 0390 3,9 mm 10 75 mm 43 mm703 540 0400 4,0 mm 10 75 mm 43 mm703 540 0410 4,1 mm 10 75 mm 43 mm703 540 0420 4,2 mm 10 75 mm 43 mm703 540 0425 4,25 mm 10 75 mm 43 mm703 540 0430 4,3 mm 10 80 mm 47 mm703 540 0440 4,4 mm 10 80 mm 47 mm703 540 0450 4,5 mm 10 80 mm 47 mm703 540 0460 4,6 mm 10 80 mm 47 mm703 540 0470 4,7 mm 10 80 mm 47 mm703 540 0475 4,75 mm 10 80 mm 47 mm703 540 0480 4,8 mm 10 86 mm 52 mm703 540 0490 4,9 mm 10 86 mm 52 mm703 540 0500 5,0 mm 10 86 mm 52 mm703 540 0510 5,1 mm 10 86 mm 52 mm703 540 0520 5,2 mm 10 86 mm 52 mm703 540 0525 5,25 mm 10 86 mm 52 mm703 540 0530 5,3 mm 10 86 mm 52 mm
703 540 0540 5,4 mm 10 93 mm 57 mm703 540 0550 5,5 mm 10 93 mm 57 mm703 540 0560 5,6 mm 10 93 mm 57 mm703 540 0570 5,7 mm 10 93 mm 57 mm703 540 0575 5,75 mm 10 93 mm 57 mm703 540 0580 5,8 mm 10 93 mm 57 mm703 540 0590 5,9 mm 10 93 mm 57 mm703 540 0600 6,0 mm 10 93 mm 57 mm703 540 0610 6,1 mm 10 101 mm 63 mm703 540 0620 6,2 mm 10 101 mm 63 mm703 540 0625 6,25 mm 10 101 mm 63 mm703 540 0630 6,3 mm 10 101 mm 63 mm703 540 0640 6,4 mm 10 101 mm 63 mm703 540 0650 6,5 mm 10 101 mm 63 mm703 540 0660 6,6 mm 10 101 mm 63 mm703 540 0670 6,7 mm 10 101 mm 63 mm703 540 0675 6,75 mm 10 109 mm 69 mm703 540 0680 6,8 mm 10 109 mm 69 mm703 540 0690 6,9 mm 10 109 mm 69 mm703 540 0700 7,0 mm 10 109 mm 69 mm703 540 0710 7,1 mm 10 109 mm 69 mm703 540 0720 7,2 mm 10 109 mm 69 mm703 540 0725 7,25 mm 10 109 mm 69 mm703 540 0730 7,3 mm 10 109 mm 69 mm703 540 0740 7,4 mm 10 109 mm 69 mm703 540 0750 7,5 mm 10 109 mm 69 mm703 540 0760 7,6 mm 5 117 mm 75 mm703 540 0770 7,7 mm 5 117 mm 75 mm703 540 0775 7,75 mm 5 117 mm 75 mm703 540 0780 7,8 mm 5 117 mm 75 mm703 540 0790 7,9 mm 5 117 mm 75 mm703 540 0800 8,0 mm 5 117 mm 75 mm703 540 0810 8,1 mm 5 117 mm 75 mm703 540 0820 8,2 mm 5 117 mm 75 mm703 540 0825 8,25 mm 5 117 mm 75 mm703 540 0830 8,3 mm 5 117 mm 75 mm703 540 0840 8,4 mm 5 117 mm 75 mm703 540 0850 8,5 mm 5 117 mm 75 mm703 540 0860 8,6 mm 5 125 mm 81 mm703 540 0870 8,7 mm 5 125 mm 81 mm703 540 0875 8,75 mm 5 125 mm 81 mm703 540 0880 8,8 mm 5 125 mm 81 mm703 540 0890 8,9 mm 5 125 mm 81 mm703 540 0900 9,0 mm 5 125 mm 81 mm703 540 0910 9,1 mm 5 125 mm 81 mm703 540 0920 9,2 mm 5 125 mm 81 mm703 540 0925 9,25 mm 5 125 mm 81 mm703 540 0930 9,3 mm 5 125 mm 81 mm703 540 0940 9,4 mm 5 125 mm 81 mm703 540 0950 9,5 mm 5 125 mm 81 mm703 540 0960 9,6 mm 5 125 mm 81 mm
703 540 0970 9,7 mm 5 133 mm 87 mm703 540 0975 9,75 mm 5 133 mm 87 mm703 540 0980 9,8 mm 5 133 mm 87 mm703 540 0990 9,9 mm 5 133 mm 87 mm703 540 1000 10,0 mm 5 133 mm 87 mm703 540 1010 10,1 mm 5 133 mm 87 mm703 540 1020 10,2 mm 5 133 mm 87 mm703 540 1030 10,3 mm 1 133 mm 87 mm703 540 1040 10,4 mm 1 133 mm 87 mm703 540 1050 10,5 mm 1 133 mm 87 mm703 540 1060 10,6 mm 1 142 mm 94 mm703 540 1070 10,7 mm 1 142 mm 94 mm703 540 1080 10,8 mm 1 142 mm 94 mm703 540 1090 10,9 mm 1 142 mm 94 mm703 540 1100 11,0 mm 1 142 mm 94 mm703 540 1120 11,2 mm 1 142 mm 94 mm703 540 1150 11,5 mm 1 142 mm 94 mm703 540 1180 11,8 mm 1 142 mm 94 mm703 540 1200 12,0 mm 1 151 mm 101 mm703 540 1220 12,2 mm 1 151 mm 101 mm703 540 1250 12,5 mm 1 151 mm 101 mm703 540 1280 12,8 mm 1 151 mm 101 mm703 540 1300 13,0 mm 1 151 mm 101 mm
Tools and machines | 936
THE WORK SHOP EXPERTMetal drill
TK7105
Standard values for twist drills SAS-PW-HSS and SAS-Plus C-HSS Cutting speeds and rpmThese values apply to drilling depths of around 3 – 4 times the hole diameter . When drilling very deep holes in difficult working conditions, the average values must be ascertained by trial and error .
Material drill cooling cutting medium speeds (rpm)
Quality medium speed speed with drill Ø Vc m/min Ø 2 Ø 5 Ø 8 Ø 12
Autom . steel (S, P, Pb all .) SAS-P W-HSS KM 200 30 – 50 5600 2250 1400 930Unall . construct . steel up to 500 N/mm2 FE-Universal
Unalloyed constructional steel SAS-P W-HSS KM 200 25 – 35 4750 1900 1200 800500-700 N/mm2 FE-Universal
Unalloyed constructional steel SAS-P W-HSS KM 200 10 – 15 2100 860 540 360700-900 N/mm2 FE-Universal Unalloyed cast steel SAS-P W-HSS KM 200 20 – 30 3980 1580 995 665 Up to 700 N/mm2 FE-Universal
All . cast steel SAS-P W-HSS KM 200 10 – 20 2380 950 595 400 FE-Universal All . steel SAS-P W-HSS KM 200 10 – 15 2100 860 540 360700-900 N/mm2 FE-Universal
All . cr-ni steel SAS-P W-HSS KM 200 8 – 12 1590 635 400 265900-1100 N/mm2 SAS-Plus C-HSS FE-Universal All . cr-ni-mo steel SAS-Plus C-HSS KM 200 6 – 10 1275 505 320 2101100-1200 N/mm2 FE-Universal
Rust and acid resist . steel SAS-Plus C-HSS KM 200 6 – 10 1275 505 320 210 FE-Universal Heat resist . steel SAS plus C-HSS KM 200 6 – 10 1275 505 320 210 FE Universal
Titan and titan alloys SAS plus C-HSS stainless steel 3 – 6 715 285 180 120 Cutting paste
Ferro-Tic SAS plus C-HSS dry 3 – 6 715 285 180 120 Pr . air Grey cast iron up to 200 HB SAS-P W-HSS dry 15 – 25 3185 1265 795 530 Pr . air Grey cast iron 350 HB SAS-P W-HSS dry 5 – 15 1590 635 400 265 (Chilled cast iron) SAS plus C-HSS pr . air
Messing, brittle SAS-P W-HSS KM 300 60 – 100 12740 5100 3200 2100 Ms 58 dry, oil Messing, ductile SAS-P W-HSS KM 300 35 – 60 7560 3020 2000 1260 Ms 60, Ms 63 BM special, oil
Cast material, copper SAS-P W-HSS KM 300 20 – 40 4745 1900 1195 795 (Soft) BM special, oil Al . copper SAS-P W-HSS KM 300 15 – 35 3980 1585 995 665 BM special, oil Electrolytic copper SAS-P W-HSS KM 300 20 – 35 4400 1750 1100 730 BM special, oil Aluminium SAS-P W-HSS KM 300 40 – 100 11140 4435 2785 1855 BM special Al . all . SAS-P W-HSS KM 300 30 – 65 7600 3030 1900 1260 Long chipping BM special
Al . all . SAS-P W-HSS KM 300 30 – 60 7200 2900 1800 1200 Short chipping BM special
Al . si all . SAS-P W-HSS KM 300 30 – 50 6365 2535 1590 1060 Silumin BM special Magnesium all . SAS-P W-HSS dry 60 – 100 12740 5100 3200 2100 Electron stainless steel Cutting paste Zinc SAS-P W-HSS KM 300 35 – 50 6800 2700 1700 1130 Zinc all . BM special Plastic materials hard SAS-P W-HSS dry 10 – 20 2380 950 595 400(Thermoset) pr . air
Plastic materials soft SAS-P W-HSS water 20 – 40 4745 1900 1195 795(Thermoset) pr . air
Tools and machines | 937
THE WORK SHOP EXPERTMetal drill
TK7105
Twist drill diameters for tapping drill holes
Metric/ISO Metric Whitworth Whitworth Fine/ISO BSW RohR BSP Nom, thread Ø Drill Ø Nom, thread Ø Drill Ø
M 1 0,75 M 3 x 0,35 2,6 1/16 1,2 R 1/8 8,7
M 1,1 0,85 M 3,5 x 0,35 3,1 3/32 1,9 R 1/4 11,7
M 1,2 0,95 M 4 x 0,35 3,6 1/8 2,6 R 3/8 15,25
M 1,4 1,1 M 4 x 0,5 3,5 5/32 3,2 R 1/2 19
M 1,6 1,25 M 4,5 x 0,5 4 3/16 3,8 R 5/8 21
M 1,7 1,3 M 5 x 0,5 4,5 7/32 4,6 R 3/4 24,5
M 1,8 1,4 M 5,5 x 0,5 5 1/4 5,1 R 7/8 28,25
M 2 1,6 M 6 x 0,75 5,2 5/16 6,5 R 1 30,5
M 2,2 1,7 M 7 x 0,75 6,2 3/8 7,9 R 1 1/8 35,5
M 2,3 1,9 M 8 x 0,75 7,2 7/6 9,25 R 1 1/4 39,5
M 2,5 2,0 M 8 x 1 7 1/2 10,5 R 1 3/8 41,5
M 2,6 2,1 M 9 x 1 8 9/16 12 R 1 1/2 45
M 3 2,5 M 10 x 1 9 5/8 13,5 R 1 3/4 51
M 3,5 2,9 M 11 x 1 10 3/4 16,5 R 2 57
M 4 3,3 M 12 x 1,5 10,5 7/8 19,5 R 2 1/4 63,3
M 4,5 3,8 M 14 x 1,5 12,5 1 22 R 2 1/2 72,8
M 5 4,2 M 16 x 1,5 14,5 1 1/8 25 R 2 3/4 79
M 5,5 4,6 M 18 x 1,5 16,5 1 1/4 28 R 3 85,5
M 6 5 M 20 x 1,5 18,5 1 3/8 30,5
M 7 6 M 22 x 1,5 20,5 1 1/2 33,5
M 8 6,8 M 24 x 1,5 22,5 1 5/8 35,5
M 9 7,8 M 25 x 1,5 23,5 1 3/4 39
M 10 8,5 M 26 x 1,5 24,5 1 7/8 41,5
M 11 9,5 M 27 x 1,5 25,5 2 44,5
M 12 10,2 M 28 x 1,5 26,5
M 14 12 M 30 x 1,5 28,5
M 16 14 M 32 x 1,5 30,5
M 18 15,5 M 33 x 1,5 31,5
M 20 17,5 M 35 x 1,5 33,5
M 22 19,5 M 36 x 1,5 34,5
M 24 21 M 38 x 1,5 36,5
M 27 24 M 39 x 1,5 37,5
M 30 26,5 M 40 x 1,5 38,5
M 33 29,5 M 42 x 1,5 40,5
M 36 32 M 45 x 1,5 43,5
M 39 35 M 48 x 1,5 46,5
M 42 37,5 M 50 x 1,5 48,5
M 45 40,5 M 52 x 1,5 50,5
M 48 43
M 52 47
The following guidelines apply to metric threads (ISO) with abnormal fine pitches: Thread hole= Nominal thread size minus pitch (0 .05 mm values rounded up to the next full 0 .1 mm ) .Example: M 18 x 1 .25 mm = 16 .8 mm thread hole diameter .
Tools and machines | 938
THE WORK SHOP EXPERTMetal drill
TK7105
Spiral drill HSS DIN 338 blank ground• With cylinder shaft, short version
• Profile-cut, blank quality
• With split point according to DIN 1412 C from ø 3 .0 mm
• 118° point angle
Areas of use:Standard drill for the drilling of steel and cast (alloyed and non-alloyed), grey cast iron, malleable cast iron, spheroidal iron, sinter iron, nickel silver, graphite
Art. No. Ø mm
U n i t
Overall length
mm
Chip flute length mm
Art. No. Ø mm
U n i t
Overall length
mm
Chip flute length mm
Art. No. Ø mm
U n i t
Overall length
mm
Chip flute length mm
703 500 0100 1,0 mm 10 34 mm 12 mm703 500 0110 1,1 mm 10 36 mm 14 mm703 500 0120 1,2 mm 10 38 mm 16 mm703 500 0130 1,3 mm 10 38 mm 16 mm703 500 0140 1,4 mm 10 40 mm 18 mm703 500 0150 1,5 mm 10 40 mm 18 mm703 500 0160 1,6 mm 10 43 mm 20 mm703 500 0170 1,7 mm 10 43 mm 20 mm703 500 0180 1,8 mm 10 46 mm 22 mm703 500 0190 1,9 mm 10 46 mm 22 mm703 500 0200 2,0 mm 10 49 mm 24 mm703 500 0210 2,1 mm 10 49 mm 24 mm703 500 0220 2,2 mm 10 53 mm 27 mm703 500 0230 2,3 mm 10 53 mm 27 mm703 500 0240 2,4 mm 10 57 mm 30 mm703 500 0250 2,5 mm 10 57 mm 30 mm703 500 0260 2,6 mm 10 57 mm 30 mm703 500 0270 2,7 mm 10 61 mm 33 mm703 500 0280 2,8 mm 10 61 mm 33 mm703 500 0290 2,9 mm 10 61 mm 33 mm703 500 0300 3,0 mm 10 61 mm 33 mm703 500 0310 3,1 mm 10 65 mm 36 mm703 500 0320 3,2 mm 10 65 mm 36 mm703 500 0330 3,3 mm 10 65 mm 36 mm703 500 0340 3,4 mm 10 70 mm 39 mm703 500 0350 3,5 mm 10 70 mm 39 mm703 500 0360 3,6 mm 10 70 mm 39 mm703 500 0370 3,7 mm 10 70 mm 39 mm703 500 0380 3,8 mm 10 75 mm 43 mm703 500 0390 3,9 mm 10 75 mm 43 mm703 500 0400 4,0 mm 10 75 mm 43 mm703 500 0410 4,1 mm 10 75 mm 43 mm703 500 0420 4,2 mm 10 75 mm 43 mm
703 500 0430 4,3 mm 10 80 mm 47 mm703 500 0440 4,4 mm 10 80 mm 47 mm703 500 0450 4,5 mm 10 80 mm 47 mm703 500 0460 4,6 mm 10 80 mm 47 mm703 500 0470 4,7 mm 10 80 mm 47 mm703 500 0480 4,8 mm 10 86 mm 52 mm703 500 0490 4,9 mm 10 86 mm 52 mm703 500 0500 5,0 mm 10 86 mm 52 mm703 500 0510 5,1 mm 10 86 mm 52 mm703 500 0520 5,2 mm 10 86 mm 52 mm703 500 0530 5,3 mm 10 86 mm 52 mm703 500 0540 5,4 mm 10 93 mm 57 mm703 500 0550 5,5 mm 10 93 mm 57 mm703 500 0560 5,6 mm 10 93 mm 57 mm703 500 0570 5,7 mm 10 93 mm 57 mm703 500 0580 5,8 mm 10 93 mm 57 mm703 500 0590 5,9 mm 10 93 mm 57 mm703 500 0600 6,0 mm 10 93 mm 57 mm703 500 0610 6,1 mm 10 101 mm 63 mm703 500 0620 6,2 mm 10 101 mm 63 mm703 500 0630 6,3 mm 10 101 mm 63 mm703 500 0640 6,4 mm 10 101 mm 63 mm703 500 0650 6,5 mm 10 101 mm 63 mm703 500 0660 6,6 mm 10 101 mm 63 mm703 500 0670 6,7 mm 10 101 mm 63 mm703 500 0680 6,8 mm 10 109 mm 69 mm703 500 0690 6,9 mm 10 109 mm 69 mm703 500 0700 7,0 mm 10 109 mm 69 mm703 500 0710 7,1 mm 10 109 mm 69 mm703 500 0720 7,2 mm 10 109 mm 69 mm703 500 0730 7,3 mm 10 109 mm 69 mm703 500 0740 7,4 mm 10 109 mm 69 mm703 500 0750 7,5 mm 10 109 mm 69 mm
703 500 0760 7,6 mm 10 117 mm 75 mm703 500 0770 7,7 mm 10 117 mm 75 mm703 500 0780 7,8 mm 10 117 mm 75 mm703 500 0790 7,9 mm 10 117 mm 75 mm703 500 0800 8,0 mm 10 117 mm 75 mm703 500 0810 8,1 mm 10 117 mm 75 mm703 500 0820 8,2 mm 10 117 mm 75 mm703 500 0830 8,3 mm 10 117 mm 75 mm703 500 0840 8,4 mm 10 117 mm 75 mm703 500 0850 8,5 mm 10 117 mm 75 mm703 500 0860 8,6 mm 10 125 mm 81 mm703 500 0870 8,7 mm 10 125 mm 81 mm703 500 0880 8,8 mm 10 125 mm 81 mm703 500 0890 8,9 mm 10 125 mm 81 mm703 500 0900 9,0 mm 10 125 mm 81 mm703 500 0910 9,1 mm 10 125 mm 81 mm703 500 0920 9,2 mm 10 125 mm 81 mm703 500 0930 9,3 mm 10 125 mm 81 mm703 500 0940 9,4 mm 10 125 mm 81 mm703 500 0950 9,5 mm 10 125 mm 81 mm703 500 0960 9,6 mm 10 125 mm 81 mm703 500 0970 9,7 mm 10 133 mm 87 mm703 500 0980 9,8 mm 10 133 mm 87 mm703 500 0990 9,9 mm 10 133 mm 87 mm703 500 1000 10,0 mm 10 133 mm 87 mm703 500 1020 10,2 mm 10 133 mm 87 mm703 500 1050 10,5 mm 10 133 mm 87 mm703 500 1100 11,0 mm 5 142 mm 94 mm703 500 1150 11,5 mm 5 142 mm 94 mm703 500 1200 12,0 mm 5 151 mm 101 mm703 500 1250 12,5 mm 5 151 mm 101 mm703 500 1300 13,0 mm 5 151 mm 101 mm
Art No. Description Contents Size Standard703 530 Special drill bit box, bare metal, ground 19 pcs . 1,0 – 10,0 mm DIN 338703 531 Special drill bit box, bare metal, ground 25 pcs . 1,0 – 13,0 mm DIN 338
Tools and machines | 939
THE WORK SHOP EXPERTMetal drill
TK7105
Spiral drill HSS DIN 340 blank ground• Standard drill for drilling of deep holes and drilling through
Boring bushes, for use as deep hole drill small movements and frequent chip removal are necessary
• High performance, stable, smooth running, high chipping performance, low welding tendency on the cutting surfaces good chip disposal, clockwise cutting
Areas of use:• For drilling steel and cast steel (alloy and non alloy), grey steel, malleable steel,
spheroidal steel, sinter iron, nickel silver, graphite
Technical specifications:• With cylinder shaft, long version
• Profile-cut, blank quality
• With splitpoint according to DIN 1412 C from ø 3 .0 mm
• 118° point angle
Art. No.
ø m
m
unit
Overall length
mm
Chip flute length mm
703 532 0100 1,0 mm 10 56 mm 33 mm703 532 0150 1,5 mm 10 70 mm 45 mm703 532 0200 2,0 mm 10 85 mm 56 mm703 532 0250 2,5 mm 10 95 mm 62 mm703 532 0290 2,9 mm 10 100 mm 66 mm703 532 0300 3,0 mm 10 100 mm 66 mm703 532 0310 3,1 mm 10 106 mm 69 mm703 532 0320 3,2 mm 10 106 mm 69 mm703 532 0350 3,5 mm 10 112 mm 73 mm703 532 0380 3,8 mm 10 119 mm 78 mm703 532 0390 3,9 mm 10 119 mm 78 mm703 532 0400 4,0 mm 10 119 mm 78 mm703 532 0410 4,1 mm 10 119 mm 78 mm703 532 0420 4,2 mm 10 119 mm 78 mm703 532 0430 4,3 mm 10 126 mm 82 mm703 532 0450 4,5 mm 10 126 mm 82 mm703 532 0480 4,8 mm 10 132 mm 87 mm703 532 0490 4,9 mm 10 132 mm 87 mm703 532 0500 5,0 mm 10 132 mm 87 mm703 532 0510 5,1 mm 10 132 mm 87 mm703 532 0520 5,2 mm 10 132 mm 87 mm703 532 0550 5,5 mm 10 139 mm 91 mm703 532 0580 5,8 mm 10 139 mm 91 mm703 532 0600 6,0 mm 5 139 mm 91 mm703 532 0620 6,2 mm 5 148 mm 97 mm703 532 0650 6,5 mm 5 139 mm 97 mm703 532 0680 6,8 mm 5 156 mm 102 mm703 532 0700 7,0 mm 5 156 mm 102 mm703 532 0720 7,2 mm 5 156 mm 102 mm703 532 0750 7,5 mm 5 156 mm 102 mm703 532 0780 7,8 mm 5 165 mm 109 mm703 532 0800 8,0 mm 5 165 mm 109 mm703 532 0820 8,2 mm 5 165 mm 109 mm703 532 0850 8,5 mm 5 165 mm 109 mm703 532 0900 9,0 mm 5 175 mm 115 mm703 532 0950 9,5 mm 5 175 mm 115 mm703 532 0980 9,8 mm 5 184 mm 121 mm703 532 1000 10,0 mm 5 184 mm 121 mm703 532 1020 10,2 mm 5 184 mm 121 mm703 532 1050 10,5 mm 5 184 mm 121 mm703 532 1100 11,0 mm 5 195 mm 128 mm703 532 1150 11,5 mm 5 195 mm 128 mm703 532 1200 12,0 mm 5 205 mm 134 mm703 532 1250 12,5 mm 5 205 mm 134 mm703 532 1300 13,0 mm 5 205 mm 134 mm703 532 1400 14,0 mm 1 214 mm 140 mm703 532 1500 15,0 mm 1 220 mm 144 mm
Tools and machines | 940
THE WORK SHOP EXPERTMetal drill
TK7105
Spiral drill HSS DIN 338 rolled• Very stable spiral drills for steel and steel alloys up to
900 N/mm², grey, malleable, and spheroidal cast iron, bronze, brass, aluminium etc .
• Consisting of fine-grain high performance quick steel
• Guarantees best cutting perfromance through high finishing precision, point cut of 118°, highest run exactness as well as specialhardening, this causes reduced welding tendency and high resistance to breaking
• With cylinder shaft
• Short version
• Rolled standard version
• Surface of a cone cut 118°
Areas of use:Standard drill for the drilling of steel and cast (alloyed and non-alloyed), grey cast iron, malleable cast iron, spheroidal iron, sinter iron, nickel silver, graphite
Technical specifications:Tolerance: h8
Material: HSS
Point bevel: Surface of a cone
Point angle: 118°
Core thickness: normal
Core increase: normal
Side chip angle / Spiral angle: normal
Groove form: normal
Other construction
Characteristics according to: DIN 1414
Surface: steam-treated
Art. No.
ø m
m
Overall length
mm
Chip flute length mm
703 001 1,0 mm 12 mm 34 mm703 002 1,5 mm 18 mm 40 mm703 003 2,0 mm 24 mm 49 mm703 004 2,5 mm 30 mm 57 mm703 005 3,0 mm 33 mm 61 mm703 006 3,1 mm 36 mm 65 mm703 007 3,3 mm 36 mm 65 mm703 008 3,5 mm 39 mm 70 mm 703 009 3,7 mm 39 mm 70 mm703 010 4,0 mm 43 mm 75 mm703 011 4,1 mm 43 mm 75 mm703 012 4,2 mm 43 mm 75 mm703 013 4,5 mm 47 mm 80 mm703 014 4,9 mm 52 mm 86 mm703 015 5,0 mm 52 mm 86 mm703 016 5,1 mm 52 mm 86 mm703 017 5,5 mm 57 mm 93 mm703 018 6,0 mm 57 mm 93 mm 703 019 6,1 mm 63 mm 101 mm703 020 6,5 mm 63 mm 101 mm703 021 6,6 mm 63 mm 101 mm703 022 6,8 mm 69 mm 109 mm703 023 7,0 mm 69 mm 109 mm703 024 7,1 mm 69 mm 109 mm703 025 7,5 mm 69 mm 109 mm703 026 7,8 mm 75 mm 117 mm703 027 8,0 mm 75 mm 117 mm703 028 8,5 mm 75 mm 117 mm703 029 9,0 mm 81 mm 125 mm703 030 9,1 mm 81 mm 125 mm703 031 9,5 mm 81 mm 125 mm703 032 10,0 mm 87 mm 133 mm703 033 10,2 mm 87 mm 133 mm703 034 10,5 mm 87 mm 133 mm703 035 11,0 mm 94 mm 142 mm703 036 11,5 mm 94 mm 142 mm703 037 12,0 mm 101 mm 151 mm703 038 12,5 mm 101 mm 151 mm703 039 13,0 mm 101 mm 151 mm
Art No. Description Size Contents Standard703 061 Special drill bit box 1,0 – 13,0 mm 25 pcs . DIN 338703 062 Special drill bit box 1,0 – 10,0 mm 19 pcs . DIN 338703 050 HSS drill bit set 179 pcs . DIN 338
Tools and machines | 941
THE WORK SHOP EXPERTMetal drill
TK7105
Spiral drill HSS with twisted shaft• With cylinder shaft
• Short version
• Rolled with offset shaft
• Surface of a cone cut 118°
• High run-out exactness
• High metal cutting performance
• Long lifetime, high resistance to breaking also after multiple re-grinding
• Low welding tendency on the cutting surfaces
• Surface hardening blue coating
• Clockwise cutting
Areas of use:For normal drilling in commonly used materials, for steel and cast steel alloyed and non-alloyed, grey cast iron, malleable cast iron, sinter iron, spheroidal cast iron, graphite, bronze, brass tenacious, aluminium short chipping, especially adequate for the use in manual drilling machines for drilling of thin-walled material like steel sheets, brass sheets, aluminium sheets, plastic sheets . Ideal for car body and metal construction .
Technical specifications:Tolerance: h8Material: HSSPoint bevel: Surface of a conePoint angle: 118°Core thickness: normalCore increase: normalSide chip angle / Spiral angle: normalGroove form: normalOther constructionCharacteristics according to: DIN 1414
Art. No.
ø m
m
Overall length
mm
Chip flute length mm
703 140 14 mm 108 mm 160 mm703 141 15 mm 114 mm 169 mm703 142 16 mm 120 mm 178 mm703 143 17 mm 125 mm 184 mm703 144 18 mm 130 mm 191 mm703 145 19 mm 135 mm 198 mm703 146 20 mm 140 mm 205 mm703 147 21 mm 145 mm 205 mm703 148 22 mm 150 mm 210 mm703 149 23 mm 155 mm 215 mm703 150 24 mm 160 mm 220 mm703 151 25 mm 160 mm 220 mm
Tools and machines | 942
THE WORK SHOP EXPERTMetal drill
TK7105
Morse taper drill HSS DIN 345• High-performance standard drill with morse taper,
adequate for all normal drilling in commonly used materials
• Extruded version without framework interruption for high stability, therefore more elastic and adequate for robust work
• First-class lifetime, high chipping performance
• Low welding tendency on the cutting surfaces, good chip disposal
• Surface hardening vaporized
• Clockwise cutting
Areas of use:For steel and cast steel alloyed and non-alloyed, (up to approx . 900 N/mm² hardness), grey cast iron, malleable cast iron, sinter iron, nickel silver, pressure casting, graphite, bronze, aluminium short chipping, and brass tenacious
Technical specifications:Tolerance h8Material HSSPoint cut Surface of a conePoint angle 118°Core thickness normalCore increase normalSide chip angle / Spiral angle normalGroove form normalOther constructionCharacteristics according to DIN 1414
Art No. Dimensions MK703 700 14,5 mm 2703 701 15,0 mm 2703 702 15,5 mm 2703 703 16,0 mm 2703 704 16,5 mm 2703 705 17,0 mm 2703 706 17,5 mm 2703 707 18,0 mm 2703 708 18,5 mm 2703 709 19,0 mm 2703 710 19,5 mm 2703 711 20,0 mm 2703 712 20,5 mm 2703 713 21,0 mm 2703 714 21,5 mm 2703 715 22,0 mm 2703 716 22,5 mm 2703 717 23,0 mm 2703 718 23,5 mm 3703 719 24,0 mm 3703 720 24,5 mm 3703 721 25,0 mm 3703 722 25,5 mm 3703 723 26,0 mm 3703 724 26,5 mm 3703 725 27,0 mm 3703 726 27,5 mm 3703 727 28,0 mm 3703 728 28,5 mm 3703 729 29,0 mm 3703 730 29,5 mm 3703 731 30,0 mm 3703 732 30,5 mm 3703 733 31,0 mm 3703 734 31,5 mm 3703 735 32,0 mm 4703 736 32,5 mm 4703 737 33,0 mm 4703 738 33,5 mm 4703 739 34,0 mm 4703 740 34,5 mm 4703 741 35,0 mm 4
Reducing sleeves DIN 2185 with morse taper
Taper drift
Art No. Description Size703 800 Reduction sleeves DIN 2185 with morse taper AK 2 to IK 1703 801 Reduction sleeves DIN 2185 with morse taper AK 3 to IK 1703 802 Reduction sleeves DIN 2185 with morse taper AK 3 to IK 2703 803 Reduction sleeves DIN 2185 with morse taper AK 4 auf IK 1703 804 Reduction sleeves DIN 2185 with morse taper AK 4 to IK 2703 805 Reduction sleeves DIN 2185 with morse taper AK 4 to IK 3703 807 Reduction sleeves DIN 2185 with morse taper AK 5 to IK 4
Art No. Description Size703 811 Taper drift MK 1–3703 812 Taper drift MK 3–4
Tools and machines | 943
THE WORK SHOP EXPERTMetal drill
TK7105
Double end drilling HSS with cylinder shaft• Good centrification, low advance force, improved chip transport
• Double-sided use in manual drills
• Profile-cut quality
• 118° point angle with split point
• Short spirals
• Double-sided use, double operating profitability
• Maximum break resistance
• Outside rounded (no fibres)
• The drill cannot catch after breaching the sheet metal
• Important for the rivets: The drill hole is not expanded
• Split point = self-tightening
• Clockwise cutting
Areas of use:Especially adequate for the processing of thin-walled materials, e .g . car body construction, rivet holes, flat and profile irons, main use in manual drilling machines
Technical specifications:Tolerance: h8Material: HSSPoint bevel: Surface of a cone double-sidedPoint angle: 135°Point thinning: DIN 1412, Form C, split pointCore thickness: normalCore increase: normalSide chip angle / Spiral angle: normalGroove form: normalOther constructioncharacteristics according to: DIN 1414
Art No. Size ø Length of spiral Overall length Unit703 600 2,5 mm 9,5 43 10703 601 3,0 mm 9,5 46 10703 602 3,1 mm 9,5 49 10703 603 3,2 mm 9,5 49 10703 604 3,3 mm 9,5 49 10703 605 3,4 mm 13 52 10703 607 4,0 mm 13 55 10703 608 4,1 mm 13 55 10703 609 4,2 mm 13 55 10703 610 4,5 mm 16 58 10703 612 4,9 mm 16 62 10703 613 5,0 mm 16 62 10703 615 5,2 mm 16 62 10
Turbo-milling drill• Made of high-quality high performance
quick steel with short spiral drill part
• Useable for drilling and cutting of contours in one work process
• Ideal rotation 1 .200 rpm
Areas of use:For drilling and cutting in sheet metal, wood, plastic, and thin-walled materials Short spiral drill part, merging into cutting with chip breakers
Technical specifications:Point bevel: Surface of a cone cutPoint angle: 118°Surface: blank / TINClockwise cutting Art No. Description Size ø Overall length
704 110 Turbo-milling drill 6,0 mm 90 mm
Tools and machines | 944
THE WORK SHOP EXPERTMetal drill
TK7105
Taper and deburring countersink 90° HSSG• The chip grooves are cut into the hardened material via CBN-procedure
• Made of CBN (cubic crystalline bornitrid)
• Due to the increased hardness the material is cut cleanly in the process, and the cutting edges therefore maintain form and remain sharper
• The milled cutting edges are smooth and sharp, therefore increased cutting performance and essentially better lifetime
• The axial back cut guarantees a clean cut with lowest possible heat generation
• The CBN-cut counter and deburring sinker provides excellent chip disposal, allows smooth working, produces a groove-free surface, and has best centering characteristics
• Significant improvement of the lifetime and surface hardening of the tool with cutting spray or cutting paste
• Best results with low cutting speed
Areas of use:The ideal tool for groove-free, smooth sinking . Deburring and sinking in steel, colour, and lightweight metals .
• Electric industry
• Sanitary and heating technology
• Automobile industry
• Machine construction
• Switchboard construction
• Steel pipe construction
• Non-ferrous metals
• Stainless steel sheets
• Furniture, wood, or aerospace industry
• Thermoplastic and duroplastic synthetics and all common steel sheets
Technical specifications:Sink angle: 90°Shaft: cylindricalCutting edges: 3Surface: blankRight-side cutting
Art No. Description Size ø Contents704 137 Taper and deburring countersinker box 6,3 – 20,5 mm 6 pcs .
Art. No. Diam. Overall length
Shaft ø Counterbore DIN 74
unit
d1 d2 ø mm BF704 128 6,30 mm 1,5 mm 5,0 mm 45,0 mm M 3 1704 129 8,30 mm 2,0 mm 6,0 mm 50,0 mm M 4 1704 130 10,40 mm 2,5 mm 6,0 mm 50,0 mm M 5 1704 131 12,40 mm 2,8 mm 8,0 mm 56,0 mm M 6 1704 132 15,00 mm 3,2 mm 10,0 mm 60,0 mm M 8 1704 133 16,50 mm 3,2 mm 10,0 mm 60,0 mm M 8 1704 134 20,50 mm 3,5 mm 10,0 mm 63,0 mm M 10 1704 135 25,00 mm 3,8 mm 10,0 mm 67,0 mm M 12 1704 136 31,00 mm 4,2 mm 12,0 mm 71,0 mm M 16 1
Single parts
Tools and machines | 945
THE WORK SHOP EXPERTTaper/deburring/countersink
TK7105
Countersink: HSS DIN 373 with firm guidance pin• For rational drilling and grinding of already existing drill holes
on sensitive and high-value work pieces with low material thickness
• Adequate for the use on manual or box column drills
• Useable on NE-metals, soft steel sheets, stainless steel sheets, duro and thermoplastic synthetics, plywood, combined wood-plastic composites and wood up to 20 mm
• For the production of counterbores for cylinder head screws, hex key screws, and nuts
• Ideal for burr-free and smooth counterbores in steel, cast, colour, and lightweight metal
• Best results with low cutting speed
• Three cutting edges
Technical specifications:Counterbore angle: 180°
Shaft: cylindrical
Cutting edges: 3
Surface: blank
Right-side cutting
Art No. Description Size ø Contents Standard704 127 Piloted counterbore box M 3 – M 10 6 pcs . DIN 373
Art. No. For threads
Counterbore
ø d2Dog point
ø d1Shaft ø d3 Overall
lengthUnit
704 122 M5 10,0 mm 5,3 mm 8,0 mm 80,0 mm 1704 123 M6 11,0 mm 6,4 mm 8,0 mm 80,0 mm 1704 124 M8 15,0 mm 8,4 mm 12,5 mm 100,0 mm 1
Single parts
Tools and machines | 946
THE WORK SHOP EXPERTTaper/deburring/countersink
TK7105
Level drill HSS Type N, right• Absolute running smoothness during drilling, as the chip grooves
are cut into the hardened material in spirals
• Especially non-inflammable chips are cleanly transported like in a spiral drill, this prevents the formation of build-up cuts and cold welding on the cutting edges
• The cone facilitates the withdrawal from pierced sheets
• Due to the high performance point the drill centers itself, this omits graining and preboring
• Due to the increased hardness the material is cut cleanly in the process, and the cutting edges therefore maintain form and remain sharper
• Due to the CNC-deep-cut spiral chip grooves, the cutting edges are smooth and sharp
• The high performance drill point with CBN-special cut allows the centering and predrilling also of thin-walled material
Areas of use:• Sheet processing (sanitary and heating technology, automobile
industry, machine construction, switchboard construction)
• Non-ferrous irons
• Stain steel sheets
• Thermoplastic and duroplastic synthetics
• All common steel sheets up to 4 mm thickness
• Centering, pre-drilling, drilling out, and deburring all in one work step
• Lifetime extension of the tool through cutting spray or cutting paste
Technical specifications:Point bevel: standard
Point thinning: DIN 1412 C
Point / Level angle: 118° / 90 °
Ø-Tolerance: standard
Surface: blank
Right-side cutting
Art No. Description704 149 Universal stepped drill box HSS size 0/9, 1 and 2
Art. No. Size number
Drilling range Overall length
Number of levels
Shaft ø
704 145 0/9 4–12 mm 65 mm 9 6 mm704 146 1 4–20 mm 75 mm 9 8 mm704 147 2 4–30 mm 100 mm 14 10 mm704 148 3 6–38 mm 100 mm 12 10 mm
Dimension: 0/9covers the following drilling ranges: 4 .0 mm 5 .0 mm 6 .0 mm 7 .0 mm 8 .0 mm 9 .0 mm10 .0 mm11 .0 mm12 .0 mm
Dimension: 2covers the following drilling ranges: 4 .0 mm 6 .0 mm 8 .0 mm10 .0 mm12 .0 mm14 .0 mm16 .0 mm18 .0 mm20 .0 mm22 .0 mm24 .0 mm26 .0 mm28 .0 mm30 .0 mm
Dimension: 1covers the following drilling ranges: 4 .0 mm 6 .0 mm 8 .0 mm10 .0 mm12 .0 mm14 .0 mm16 .0 mm18 .0 mm20 .0 mm
Dimension: 3covers the following drilling ranges: 6 .0 mm 9 .0 mm13 .0 mm 16 .0 mm19 .0 mm21 .0 mm23 .0 mm26 .0 mm29 .0 mm32 .0 mm35 .0 mm38 .0 mm
Single parts
Tools and machines | 947
THE WORK SHOP EXPERTLevel drill
TK7105
Metal sheet drill 90° HSSE• Due to the increased hardness the material is cut cleanly in the process,
and the cutting edges therefore maintain form and remain sharper
• Due to the CBN-deep-cut chip grooves the cutting edges are smooth and sharp, therefore increased cutting performance and essentially better lifetime
• Chip groove provides absolute running smoothness and high cutting performance
• The cone facilitates the withdrawal from pierced sheets
• The high performance drill point with CBN-special cut allows the centering and predrilling also of thin-walled material
Areas of use:• Electric industry
• Sanitary / Heating technology
• Automobile industry
• Machine construction
• Switchboard construction
• Aircraft industry
• Non-ferrous metals
• Stainless steel sheets
• For all common industry materials
• Thermoplastic and duroplastic synthetics and all common steel sheets with a thickness up to 4 mm
• Centering, pre-drilling, drilling out, and deburring all in one work step
• Significant lifetime extension of the tool through cutting spray or cutting paste
Technical specifications:Point bevel: standard
Point thinning: DIN 1412 C
Point angle: 118°
Cone angle: 20 – 30°
Ø-Tolerance: standard
Surface: blank
Right-side cutting
Art. No. Size number
Drilling range Overall length Shaft ø
704 138 1 3 – 14,0 mm 58 mm 6 mm704 139 2 8 – 20,0 mm 71 mm 8 mm704 140 3 16 – 30,5 mm 76 mm 9 mm704 141 4 24 – 40,0 mm 89 mm 10 mm704 142 5 36 – 50,0 mm 97 mm 12 mm
Size 1 Size 3Size 2
Size 4 Size 5
Art No. Description704 144 Sheet metal cone bit box (contains 1 ea . of bit sizes 1, 2 and 3)
Single parts
Tools and machines | 948
THE WORK SHOP EXPERTQuick helix drill
TK7105
Machine thread cutting drill HSS-E TIN DIN 371 / 376 Disc ISO-standard tap DIN.13• Machine tap drill with Titan-Nitrid-coating and DIN 371 with reinforced
shaft for professional use
• For passage taps in not alloyed and alloyed steels up to 1 .000 N/mm2 hardness and in long chipping materials like V2A, malleable iron, or non-ferrous metals
• The tap is cut in one step
Technical specifications:Tap point: Form B approx . 4 - 5 ways with spiral point
Tap: metric DIN ISO 13
Sides: back relieved
Tolerance: ISO 2 / 6 H
Surface: Titan-Nitrid coated
Direction: right cutting Art. No. Standard Nominal thread
sizePitch mm Tap hole
ø mmOverall length
mm
Thread length
mmShaft ø
mm
704 000 DIN 371 M 3 0,5 2,5 56 mm 3,5 mm704 001 DIN 371 M 4 0,7 3,3 63 mm 4,5 mm704 002 DIN 371 M 5 0,8 4,2 70 mm 6,0 mm704 003 DIN 371 M 6 1,0 5,0 80 mm 6,0 mm704 004 DIN 371 M 8 1,25 6,8 90 mm 8,0 mm704 005 DIN 371 M 10 1,5 8,5 100 mm 10,0 mm704 006 DIN 376 M 12 1,75 10,2 110 mm 9,0 mm704 006-1 DIN 376 M 14 2,0 12,0 110 mm 11,0 mm704 006-2 DIN 376 M 16 2,0 14,0 110 mm 12,0 mm
DIN 371 DIN 376
Machine thread cutting drill HSS-E DIN 371 / 376 Disc ISO-standard tap DIN.13• Machine tap made of cobalt-alloyed steel
• For passage taps in not alloyed and alloyed steels up to 900 N/mm2 hardness and in long chipping materials like malleable iron or non-ferrous metals
• High heat hardness resistance for very long lifetimes
• DIN 371 with reinforced shaft for powerful use
• The tap is cut in one step
Technical specifications:Tap point: Form B approx . 4 - 5 ways with spiral point
Tap: metric DIN ISO 13
Sides: back relieved
Tolerance: ISO 2 / 6
Surface: blank
Tap: right cutting
Art. No. Standard Nominal thread
sizePitch mm Tap hole
ø mmOverall length
mm
Thread length
mmShaft ø
mm
704 150 DIN 371 M 3 0,5 2,5 56 mm 11,0 3,5 mm704 151 DIN 371 M 4 0,7 3,3 63 mm 13,0 4,5 mm704 152 DIN 371 M 5 0,8 4,2 70 mm 16,0 6,0 mm704 153 DIN 371 M 6 1,0 5,0 80 mm 19,0 6,0 mm704 154 DIN 371 M 8 1,25 6,8 90 mm 22,0 8,0 mm704 155 DIN 371 M 10 1,50 8,5 100 mm 24,0 10,0 mm704 156 DIN 376 M 12 1,75 10,2 110 mm 22,0 9,0 mm704 157 DIN 376 M 14 2,0 12,0 110 mm 25,0 11,0 mm704 158 DIN 376 M 16 2,0 14,0 110 mm 28,0 12,0 mm
DIN 371 DIN 376
flat
poin
ted
flat
poin
ted
Tools and machines | 949
THE WORK SHOP EXPERTThread cutting tools
TK7105
Machine thread cutting drill Box HSS-E DIN 371 / 376 Disc ISO-standard tap DIN.13• 14-piece machine tap drill set in industry version,
specifically for the professional use in passage tap work
Included in delivery:• 7 x machine tap drills HSS-E DIN 371/ 376,
Form B, M 3 - M 4 - M 5 - M 6 - M 8 - M 10 and M 12
• 7 x TECHNOLIT® core-hole drill HSS-G, DIN 338, blank ground, Ø 2 .5 - 3 .3 - 4 .2 - 5 .0 - 6 .8 - 8 .5 and 10 .2 mm with splitpoint
• Stable metal industry cassette
Art No. Description Dimensions Contents704 070 Machine tap drill box, HSS-E M3 – 12 14 pcs .
DIN 371 / DIN 376
Machine thread cutting drill Box HSS-G Tolerance: M3 - M12 Disc ISO-standard tap DIN.13• 14-piece machine tap drill set in industry version,
specifically for the professional use in passage tap work
Included in delivery:• 7 x machine tap drills HSS-G DIN 371/ 376,
Form B, M 3 - M 4 - M 5 - M 6 - M 8 - M 10 and M 12
• 7 x TECHNOLIT® core-hole drill HSS-G, DIN 338, blank ground, Ø 2 .5 - 3 .3 - 4 .2 - 5 .0 - 6 .8 - 8 .5 and 10 .2 mm with splitpoint
• Stable metal industry cassette
Art No. Description Contents Dimensions Unit704 071 Machine tap drill box, HSS-G 14 pcs . M3 – 12 1 Set
DIN 371 / DIN 376
Machine thread cutting drill HSS-G DIN 371 / 376 Disc ISO-standard tap DIN.13• Machine tap drill made of HSS-steel • For passage taps in not alloyed and alloyed steels
up to 900 N/mm2 hardness and in long chipping materials like malleable iron or non-ferrous metals
• DIN 371 with reinforced shaft for powerful use• The tap is cut in one step
Technical specifications:Tap point: Form B approx . 4 - 5 ways with spiral pointTap: metric DIN ISO 13Sides: back relievedTolerance: ISO 2 / 6Surface: blankTap: right cutting
Art. No. Standard Nominal thread
sizePitch mm Tap hole
ø mmOverall length
mm
Thread length
mmShaft ø
mm
704 007 DIN 371 M 3 0,5 2,5 56 mm 11,0 3,5 mm704 008 DIN 371 M 4 0,7 3,3 63 mm 13,0 4,5 mm704 009 DIN 371 M 5 0,8 4,2 70 mm 16,0 6,0 mm704 010 DIN 371 M 6 1,0 5,0 80 mm 19,0 6,0 mm704 011 DIN 371 M 8 1,25 6,8 90 mm 22,0 8,0 mm704 012 DIN 371 M 10 1,5 8,5 100 mm 24,0 10,0 mm704 013 DIN 376 M 12 1,75 10,2 110 mm 22,0 9,0 mm
DIN 376DIN 371
Tools and machines | 950
THE WORK SHOP EXPERTThread cutting tools
TK7105
Machine thread cutting drill HSS-G – Sack hole DIN 371 / 376 Disc ISO-standard tap DIN.13• Machine tap drill made of HSS-steel
• For passage taps in not alloyed and alloyed steels up to 800 N/mm2 hardness and in long chipping materials like malleable iron or non-ferrous metals
• Right spiral grooves 35° RSP
• Machine tap drill HSS-G – Pocket hole acc . to DIN 376 with overflow shaft
• DIN 371 with reinforced shaft for powerful use
Technical specifications:Tap drill: Form C / 35° RSP approx . 2 - 3 ways
Tap: metric DIN ISO 13
Sides: back relieved
Tolerance: ISO 2 / 6 H
Surface: blank
Tap: right cuttingArt. No. Standard Nominal thread
sizePitch mm Tap hole
ø mmOverall length
mm
Thread length
mmShaft ø
mm
704 016 DIN 371 M 3 0,5 2,5 56 mm 11,0 3,5 mm704 017 DIN 371 M 4 0,7 3,3 63 mm 13,0 4,5 mm704 018 DIN 371 M 5 0,8 4,2 70 mm 16,0 6,0 mm704 019 DIN 371 M 6 1,0 5,0 80 mm 19,0 6,0 mm704 020 DIN 371 M 8 1,25 6,8 90 mm 22,0 8,0 mm704 021 DIN 371 M 10 1,5 8,5 100 mm 24,0 10,0 mm704 022 DIN 376 M 12 1,75 10,2 110 mm 22,0 9,0 mm
DIN 376DIN 371
Manual thread drill HSS-G DIN 352 Disc ISO-standard tap DIN.13• Three-piece sets consisting of pilot cutter, middle cutter, and finishing cutter
• Manual tap drill sets finished of high performance quick working steel
• For passage taps and pouch hole in not alloyed and alloyed steels up to 800 N/mm2 hardness and in long chipping materials like malleable iron or non-ferrous metals
• The tap is cut in three steps
Technical specifications:Set: 3-piece
Pilot cutter: approx . 5 - 6 step tap point
Middle cutter: approx . 4 - 5 step tap point
Finishing cutter: approx . 2 - 3 step tap point
Tap: metric DIN ISO 13
Sides: back relieved
Tolerance: ISO 2 / 6 H
Surface: blank
Tap: right cutting
Art. No. Standard Nominal thread
sizePitch mm Tap hole
ø mmOverall length
mm
Thread length
mm
704 024 DIN 352 M 3 0,5 2,5 40 mm 12,0704 025 DIN 352 M 4 0,7 3,3 45 mm 14,0704 026 DIN 352 M 5 0,8 4,2 48 mm 16,0704 027 DIN 352 M 6 1,0 5,0 50 mm 18,0704 028 DIN 352 M 8 1,25 6,8 56 mm 22,0704 029 DIN 352 M 10 1,50 8,5 70 mm 25,0704 030 DIN 352 M 12 1,75 10,2 75 mm 30,0704 031 DIN 352 M 14 2,0 12,0 80 mm 32,0704 032 DIN 352 M 16 2,0 14,0 80 mm 32,0704 033 DIN 352 M 18 2,5 15,5 95 mm 40,0704 034 DIN 352 M 20 2,5 17,5 95 mm 40,0704 035 DIN 352 M 22 2,5 19,5 100 mm 40,0704 036 DIN 352 M 24 3,0 21,0 110 mm 50,0
DIN 352
Tools and machines | 951
THE WORK SHOP EXPERTThread cutting tools
TK7105
Manual thread drill - Box HSS-G DIN 352 Disc ISO-standard tap DIN.13• 28-piece manual tap drill set in stable industry cassette
Included in delivery:• 21 x manual tap drill HSS-G, DIN 352, each 3 pieces
M 3 - M 4 - M 5 - M 6 - M 8 - M 10 and M 12
• 7 x TECHNOLIT® core-hole spiral drill HSS-G, DIN 338, blank ground, Ø 2 .5 - 3 .3 - 4 .2 - 5 .0 - 6 .8 - 8 .5 and 10 .2 mm with split point
Thread cutting kit DIN 352 / DIN EN 22568 Disc ISO-standard tap DIN.13• 44-piece thread cutting box in industry version
Included in delivery:• Manual tap drill DIN 352: M 3 - 4 - 5 - 6 - 8 - 10 - 12 (set at 3 pieces each)
• Threading die DIN 223: M 3 - 4 - 5 - 6 - 8 - 10 - 12 (1 piece each)
• Thread die holder DIN 225 for all dimensions adjustable acc . to DIN Sizes: 20 x 5/ 20 x 7/ 25 x 9/ 30 x 11/ 38 x 14 mm (1 piece each)
• Tap wrench DIN 1814 size 1 and size 2 ( 1 piece each)
• 7 x TECHNOLIT® core-hole drill HSS-G, DIN 338, blank ground, Ø 2 .5 - 3 .3 - 4 .2 - 5 .0 - 6 .8 - 8 .5 and 10 .2 mm with splitpoint
• 1 thread stencil
• 1 screwdriver
Art No. Description Dimensions Contents704 067 Manual tap drill box, HSS-G M3 – 12 29 pcs .
Art No. Description Dimensions Contents704 068 Thread cutting kit M3 – 12 43 pcs .
DIN 352 / DIN EN 22568
DIN 352 / DIN EN 22568
Thread cutting kit DIN 352 / DIN EN 22568Included in delivery:
• Hand tap DIN 352: M 3 - 4 - 5 - 6 - 8 - 10 - 12 (set of 3 each)
• Thread-cutting die DIN 223: M 3 - 4 - 5 - 6 - 8 - 10 - 12 (1 piece each)
• Die stock DIN 225, adjustable for all DIN dimensions: 20 x 5 / 20 x 7 / 25 x 9 / 30 x 11 / 38 x 14 mm (1 piece each)
• Tap wrench DIN 1814 size 1 and 2 (1 piece each)
• 7 x TECHNOLIT® tapping drill (twist drill) HSS-G, DIN 338, bright-finished (ground), ø 2 .5 - 3 .3 - 4 .2 - 5 .0 - 6 .8 - 8 .5 and 10 .2 mm with split point
• 1 thread gauge
• 1 screwdriver
Art No. Description Contents Dimensions Standard704 095 Thread-cutting set 44 pcs . M3 – M12 DIN 352 / DIN EN 22568
High-quality insert made of microcellular rubber: everything stays safely in place!
Tools and machines | 952
THE WORK SHOP EXPERTThread cutting tools
TK7105
Manual thread cutting drill HSS-G – fine thread DIN 2181 metric ISO-fine thread DIN 13• Two-piece sets consisting of pilot and finishing cutter
• Manual tap drill sets finished of high performance quick working steel
• With fine thread specifically for screws, with accordingly fine increase
• For passage taps in not alloyed and alloyed steels up to 800 N/mm2 hardness and in long chipping materials like malleable iron or non-ferrous metals
• The thread is cut in three steps
Technical specifications:Set: 2-piece
Pilot cutter: approx . 5 - 6 step tap point
Finishing cutter: approx . 2 - 3 step tap point
Tap: metric fine DIN ISO 13
Sides: back relieved
Tolerance: ISO 2 / 6 H
Surface: blank
Tap: right cutting
Art. No. Standard Nominal thread
sizePitch mm Tap hole ø
mmOverall length
mm
Thread length
mm
704 200 DIN 2181 M 8 1,0 7,0 56 mm 18,0704 201 DIN 2181 M 10 1,0 9,0 63 mm 18,0704 202 DIN 2181 M 10 1,25 8,75 63 mm 18,0704 203 DIN 2181 M 12 1,25 10,75 63 mm 20 .0704 204 DIN 2181 M 12 1,5 10,5 70 mm 20 .0704 205 DIN 2181 M 14 1,25 12,75 70 mm 20 .0704 206 DIN 2181 M 14 1,5 12,5 70 mm 20 .0704 207 DIN 2181 M 16 1,5 14,5 70 mm 20 .0704 208 DIN 2181 M 18 1,5 16,5 80 mm 22,0704 209 DIN 2181 M 20 1,5 18,5 80 mm 22,0704 210 DIN 2181 M 22 1,5 20,5 80 mm 22,0
DIN 2181
Accessories for thread cutters
Art No. Description Contents Unit903 030 Stainless steel cutting paste 60 g 1860 065 Cutting oil spray „Extra,“, BEST OF 500 ml 12/24
High grade steel cutting paste• Highly concentrated, active paste for the improvement and accel-
eration of chip removing and chipless processing of metals
• Useable for rustfree and highly alloyed, tough but flexible steel, titan, „smearing“ non-ferrous metals and also for plastics
• Applicable for cutting of outside and inside threads, for drilling, broaching, reaming, sawing, and pulling of rustfree and other highly alloyed steels
Cutting oil - spray „Extra“• Strongly additive high performance cooling lubricant for
highest requirements for difficult metal processing
• Especially long adhesion through stable power foam
• Improved cooling effect increases the lifetime of the tools
• For highly alloyed, tough but flexible steels of highest hardness, e .g . ball bearing steels, tools steel, heat-resisting austenitic or similar steels like titan or tantal and for high heat-resisting nickel-chrome-alloys
Tools and machines | 953
THE WORK SHOP EXPERTThread cutting tools
TK7105
Art. No. Standard Nominal thread size
Pitch mm External ø mm
Width in mm
704 047 EN 22568 M 3 0,5 20,0 5,0 mm704 048 EN 22568 M 4 0,7 20,0 5,0 mm704 049 EN 22568 M 5 0,8 20,0 7,0 mm704 050 EN 22568 M 6 1,0 20,0 7,0 mm704 051 EN 22568 M 8 1,25 25,0 9,0 mm704 052 EN 22568 M 10 1,5 30,0 11,0 mm704 053 EN 22568 M 12 1,75 38,0 14,0 mm704 054 EN 22568 M 14 2,0 38,0 14,0 mm704 055 EN 22568 M 16 2,0 45,0 18,0 mm704 056 EN 22568 M 18 2,5 45,0 18,0 mm704 057 EN 22568 M 20 2,5 45,0 18,0 mm704 058 EN 22568 M 22 2,5 55,0 22,0 mm704 059 EN 22568 M 24 3,0 55,0 22,0 mm
Cutting iron HSS-G EN 22568 B (former DIN 223 B) Disc ISO-standard tap DIN.13• Die finished of high performance quick working steel
• For non alloy and low alloy steels up to 800 N/mm2 hardness
• The tap is cut in one step
Technical specifications:Version: Form B closed, pre-cut
Tap: metric DIN ISO 13
Tolerance: ISO - 6g
Surface: blank
Tap: right cutting
EN 22568 B
Cutting iron HSS-G – fine thread EN 22568 B (former DIN 223 B) metric ISO-fine thread DIN 13• Die finished of high performance quick working steel
• For non alloy and low alloy steels up to 800 N/mm2 hardness
• The tap is cut in one step
Technical specifications:Version: Form B closed, pre-cut
Tap: metric fine DIN ISO 13
Tolerance: ISO - 6g
Surface: blank
Tap: right cutting
EN 22568 B
Art. No. Standard Nominal thread
sizePitch mm External ø
mmWidth in
mm
704 300 EN 22568 M 8 1,0 25,0 9,0 mm704 301 EN 22568 M 10 1,0 30,0 11,0 mm704 302 EN 22568 M 10 1,25 30,0 11,0 mm704 303 EN 22568 M 12 1,25 38,0 10,0 mm704 304 EN 22568 M 12 1,5 38,0 10,0 mm704 305 EN 22568 M 14 1,25 38,0 10,0 mm704 306 EN 22568 M 14 1,5 38,0 10,0 mm704 307 EN 22568 M 16 1,5 45,0 14,0 mm704 308 EN 22568 M 18 1,5 45,0 14,0 mm704 309 EN 22568 M 20 1,5 45,0 14,0 mm704 310 EN 22568 M 22 1,5 55,0 16,0 mm704 311 EN 22568 M 24 1,5 55,0 16,0 mm
Tools and machines | 954
THE WORK SHOP EXPERTThread cutting tools
TK7105
Art. No. Standard Size num-ber
For following metric/fine
Tap sizes Ww. Ww pipe
Overall length mm
704 041 DIN 1814 0 M 1 - 8 1/16 - 1/4 – 125 mm704 042 DIN 1814 1,1/2 M 1 - 12 1/16 - 1/2 1/8 200 mm704 043 DIN 1814 3 M 5 - 20 7/32 - 1/2 1/8 - 1/2 375 mm704 044 DIN 1814 4 M 11 - 27 7/16 - 1 1/4 - 3/4 500 mm
Wind iron adjustable DIN 1814• For thread cutting in hard to reach areas .
• With two jaw chucks for the tightening of four point shafts
• With steel handles, one handle can be screwed off
Technical specifications:Version: Casing of zinc die-cast
Chuck jaws: hardened DIN 1814
Art. No. Size number Square For following metric/fine
Tap sizes Ww. Ww pipe
Overall length mm
704 045 1 2,5 - 5,5 M 3 - 10 1/8 - 3/8 85 mm704 046 2 4,5 - 7 M 5 - 12 7/32 - 1/2 1/8 100 mm
Art. No. Standard Size num-ber
For following metric/fine
Tap sizes Ww. Ww pipe
Overall length mm
704 060 DIN 225 20 x 5 M 3 - 4 1/8 - 5/32 200 mm704 061 DIN 225 20 x 7 M 4,5 - 6 3/16 - 1/4 200 mm704 062 DIN 225 25 x 9 M 7 - 9 5/16 224 mm704 063 DIN 225 30 x 11 M 10 - 11 3/8 - 7/16 1/8 280 mm704 064 DIN 225 38 x 10 M 12 - 14 1/4 315 mm704 065 DIN 225 45 x 18 M 16 - 20 5/8 - 3/4 450 mm704 066 DIN 225 55 x 22 M 22 - 24 7/8 - 1 560 mm
Tool holder with Knarre• Specially usable in hard to reach areas
• With two jaw chucks for the tightening of four point shafts
• Adjustable cross handle with riffles on both ends for latching of the locking ball
Technical specifications:Version: adjustable left, right, fixed
Surface: chromed
Cutting iron holder DIN 225• For direct mounting of dies acc . to DIN 223/5158,
DIN EN 22568, acc . to DIN EN, DIN EN 24231
• With 5 screws for fixing of the dies
Technical specifications:Version: Made of zinc die-cast
Illustration similar! DIN 225
Tools and machines | 955
THE WORK SHOP EXPERTThread cutting tools
TK7105
T-handle die and tap set M3-M6 13-pieces
• For easy tapping, even in hard-to-reach places
• The ergonomic T-handle enables fast, powerful, and non-tiring work
• Many different uses since suitable for both male and female threads
Qualities:• All-purpose tap and die set
• Also suitable for difficult tapping jobs
• Supplied in a blue plastic case so tools are always handy
Areas of use:• Metalworking shops
• Industrial firms
• Mechanical engineering
Included in delivery:13 piece set consisting of:
• 1x T-handle ratchet with release knob and directional change
• 1x extension 75 mm
• 1x quick-action chuck for hand tap
• 1x die stock
• 4x tap for female threads M3-M6
• 4x die for male threads M3-M6
• 1x offset screwdriver
Release button for securing and releasing the inserts
Switch for forward or reverse
Reverse
Forward
Handy and ergonomic grip for easy operation
Art No. Description704 072 A T-handle die and tap set M3-M6, 13-pieces
Tools and machines | 956
THE WORK SHOP EXPERTThread cutting tools
TK7105
Carbide tipped burrs
Z 3
Universal cutting teeth (standard), characterized by a high removal rate . Can be used on even the hardest materials and ideal for toolmaking and die making . Achieves smooth, even surfaces .
Z Alu
Aluminium cutting teeth for use on aluminium and its alloys, such as magnesium, non-alloyed and non-metallic materials, as well as hard plastic, wood, natural rubber, etc .
Head diam-eter
Unhardened steel and cast steel
Hardened steel, high-strength materials
Brass, cast steel, copper, bronze
Unhardened steel and cast steel
16 8 .000 – 30 .000 12 .000 – 19 .000 9 .500 – 23 .000 18 .000 – 23 .000
15 8 .000 – 33 .000 13 .000 – 20 .000 10 .000 – 25 .000 18 .500 – 25 .000
14 8 .500 – 35 .000 15 .000 – 22 .000 10 .000 – 28 .000 20 .000 – 27 .000
13 8 .500 – 40 .000 16 .000 – 24 .000 11 .000 – 30 .000 21 .000 – 30 .000
12 8 .700 – 42 .000 18 .000 – 25 .000 12 .000 – 33 .000 23 .000 – 31 .000
11 9 .000 – 45 .000 19 .000 – 27 .000 13 .000 – 36 .000 25 .000 – 35 .000
10 10 .000 – 50 .000 20 .000 – 30 .000 15 .000 – 40 .000 28 .000 – 39 .000
9 11 .000 – 54 .000 21 .000 – 33 .000 16 .000 – 43 .000 30 .000 – 43 .000
8 12 .000 – 58 .000 24 .000 – 36 .000 19 .000 – 47 .000 35 .000 – 48 .000
7 15 .000 – 62 .000 26 .000 – 40 .000 20 .000 – 53 .000 39 .000 – 52 .000
6 18 .000 – 70 .000 30 .000 – 47 .000 24 .000 – 60 .000 41 .000 – 57 .000
5 21 .000 – 75 .000 38 .000 - 55 .000 29 .000 – 69 .000 47 .000 – 65 .000
4 25 .000 – 80 .000 45 .000 – 67 .000 35 .000 – 78 .000 51 .000 – 75 .000
3 30 .000 – 90 .000 58 .000 – 90 .000 45 .000 – 90 .000 59 .000 – 90 .000
Tools and machines | 957
THE WORK SHOP EXPERTHard metal cutting pins
TK7105
Cylindrical, with serrated tip
Type ZYA Type ZYA-S
Cylindrical, with rounded head Spherical, round
Type WRC Type KUD
Art. No. Alu
Drop-shaped Semicircular arch
Type TRE Type RBF
*Head diameter x head length x overall length
Cylindrical, without serrated tip
Art. No. Z3 Dimensions* ø ShaftArt. No. Z3 Dimensions* ø Shaft
Art. No. Z3 Dimensions* ø Shaft
Art. No. Z3 Dimensions* ø Shaft
Art. No. Alu
Art. No. Z3 Dimensions* ø Shaft Art. No. Z3 Dimensions* ø Shaft
704 322 4 x 16 x 51 mm 6 mm704 322-01 6 x 16 x 51 mm 6 mm704 322-02 8 x 20 x 64 mm 6 mm704 322-03 10 x 20 x 64 mm 6 mm704 322-04 10 x 25 x 70 mm 6 mm704 322-05 12 x 25 x 70 mm 6 mm704 322-06 16 x 25 x 70 mm 6 mm704 322-07 20 x 25 x 70 mm 6 mm704 322-08 25 x 25 x 70 mm 6 mm
704 320 4 x 16 x 51 mm 6 mm704 320-01 6 x 16 x 51 mm 6 mm704 320-02 8 x 20 x 64 mm 6 mm704 320-03 10 x 20 x 64 mm 6 mm704 320-04 10 x 25 x 70 mm 6 mm704 320-05 12 x 25 x 70 mm 6 mm704 320-06 16 x 25 x 70 mm 6 mm704 320-07 20 x 25 x 70 mm 6 mm704 320-08 25 x 25 x 70 mm 6 mm
704 323 4 x 16 x 51 mm 6 mm704 323-01 6 x 16 x 51 mm 6 mm704 323-02 8 x 20 x 64 mm 6 mm704 323-03 10 x 20 x 64 mm 6 mm704 323-05 10 x 38 x 83 mm 6 mm704 323-06 12 x 25 x 70 mm 6 mm704 323-07 16 x 25 x 70 mm 6 mm704 323-08 20 x 25 x 70 mm 6 mm704 323-09 25 x 25 x 70 mm 6 mm
704 324 3 x 3 x 51 mm 6 mm704 324-01 6 x 6 x 51 mm 6 mm704 324-02 8 x 8 x 52 mm 6 mm704 324-03 10 x 10 x 52 mm 6 mm704 324-04 12 x 11 x 56 mm 6 mm704 324-05 16 x 14 x 59 mm 6 mm704 324-06 20 x 18 x 62 mm 6 mm
704 325 6 x 10 x 51 mm 6 mm704 325-01 8 x 16 x 60 mm 6 mm704 325-02 10 x 16 x 60 mm 6 mm704 325-03 12 x 22 x 67 mm 6 mm704 325-04 16 x 25 x 70 mm 6 mm704 325-05 20 x 25 x 70 mm 6 mm
704 326 6 x 16 x 51 mm 6 mm704 326-01 8 x 20 x 64 mm 6 mm704 326-02 10 x 20 x 64 mm 6 mm704 326-03 12 x 20 x 64 mm 6 mm704 326-04 12 x 25 x 70 mm 6 mm704 326-05 16 x 25 x 70 mm 6 mm704 326-06 20 x 25 x 70 mm 6 mm
–704 322-09704 322-10704 322-11–704 322-12704 322-13––
–704 321704 321-01704 321-02704 321-03704 321-04704 321-05704 321-06704 321-07
–704 323-10–704 323-12–704 323-14704 323-15704 323-16–
–704 324-09–704 324-11704 324-12704 324-13704 324-14
––704 325-06704 325-07704 325-08704 325-09
––704 326-07–704 326-08704 326-09–
Art. No. Alu
Art. No. Alu Art. No. Alu
Art. No. Alu Art. No. Alu
Tools and machines | 958
THE WORK SHOP EXPERTHard metal cutting pins
TK7105
Pointed arch-bullet shaped Flame shaped
Type SPG Type HMB
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 333 – 6 x 16 x 51 mm 6 mm704 333-01 – 8 x 20 x 64 mm 6 mm704 333-02 – 10 x 20 x 64 mm 6 mm704 333-03 – 12 x 20 x 64 mm 6 mm704 333-04 – 12 x 25 x 70 mm 6 mm704 333-05 – 16 x 25 x 70 mm 6 mm704 333-06 – 20 x 25 x 70 mm 6 mm
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 327 – 6 x 16 x 51 mm 6 mm704 327-01 – 8 x 20 x 64 mm 6 mm704 327-02 – 10 x 25 x 64 mm 6 mm704 327-03 – 12 x 32 x 76 mm 6 mm704 327-04 – 16 x 36 x 81 mm 6 mm704 327-05 – 20 x 42 x 86 mm 6 mm
Conical 60° Conical 90°
Pointed cone
Type KSV Type KSR
Type SKM
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 328 – 6 x 5 x 51 mm 6 mm704 328-01 – 10 x 8 x 52 mm 6 mm704 328-02 – 13 x 11 x 56 mm 6 mm704 328-03 – 16 x 14 x 59 mm 6 mm704 328-04 – 19 x 18 x 62 mm 6 mm704 328-05 – 25 x 24 x 68 mm 6 mm
Art. No. Z3 Dimensions* ø ShaftArt. No. Alu
*Head diameter x head length x overall length
Round nose, conical
Type KEL
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 329 – 6 x 3 x 51 mm 6 mm704 329-01 – 10 x 5 x 49 mm 6 mm704 329-02 – 13 x 6 x 51 mm 6 mm704 329-03 – 16 x 8 x 52 mm 6 mm704 329-04 – 19 x 10 x 54 mm 6 mm704 329-05 – 25 x 13 x 57 mm 6 mm
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 331 – 6 x 13 x 51 mm 6 mm704 331-01 – 6 x 20 x 51 mm 6 mm704 331-02 – 6 x 25 x 51 mm 6 mm704 331-03 – 10 x 19 x 64 mm 6 mm704 331-04 – 12 x 25 x 70 mm 6 mm704 331-05 – 16 x 29 x 73 mm 6 mm
––704 330-06704 330-07704 330-08704 330-09
704 330 6 x 16 x 51 mm 6 mm704 330-01 8 x 24 x 67 mm 6 mm704 330-02 10 x 27 x 71 mm 6 mm704 330-03 12 x 30 x 73 mm 6 mm704 330-04 16 x 33 x 78 mm 6 mm704 330-05 20 x 38 x 83 mm 6 mm
Tools and machines | 959
THE WORK SHOP EXPERTHard metal cutting pins
TK7105
Angle, without serrated tip
Cylindrical, without serrated tip
Type WKN Type ZYA
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 332 – 6 x 6 x 51 mm 6 mm704 332-01 – 10 x 10 x 54 mm 6 mm704 332-02 – 13 x 13 x 64 mm 6 mm704 332-03 – 16 x 19 x 64 mm 6 mm
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 340 – 1,5 x 6 x 38 mm 3 mm704 340-01 – 2,4 x 13 x 38 mm 3 mm704 340-02 – 3 x 13 x 38 mm 3 mm704 340-03 – 4 x 12 x 38 mm 3 mm704 340-04 – 5 x 12 x 38 mm 3 mm704 340-05 – 6 x 13 x 51 mm 3 mm
Cylindrical, with serrated tip
Cylindrical, with rounded head
Type ZYA-S Type WRC
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 341 – 3 x 14 x 38 mm 3 mm704 341-01 – 4 x 12 x 38 mm 3 mm704 341-02 – 5 x 12 x 38 mm 3 mm704 341-03 – 6 x 13 x 51 mm 3 mm
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 342 – 2,4 x 13 x 38 mm 3 mm704 342-01 – 3 x 13 x 38 mm 3 mm704 342-02 – 4 x 12 x 38 mm 3 mm704 342-03 – 5 x 12 x 38 mm 3 mm704 342-04 – 6 x 13 x 51 mm 3 mm
Spherical, round
Type KUD
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 343 – 2,4 x 2,4 x 38 mm 3 mm704 343-01 – 3,2 x 3,2 x 38 mm 3 mm704 343-02 – 4,8 x 4,8 x 43 mm 3 mm704 343-03 – 6,4 x 6,4 x 44 mm 3 mm
Drop-shaped
Type TRE
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 344 – 3 x 6 x 38 mm 3 mm704 344-01 – 4,8 x 7 x 38 mm 3 mm704 344-02 – 6 x 10 x 48 mm 3 mm
*Head diameter x head length x overall length
Tools and machines | 960
THE WORK SHOP EXPERTHard metal cutting pins
TK7105
Pointed arch-bullet shaped Pointed cone
Type SPG Type SKM
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 346 – 2,4 x 6 x 38 mm 3 mm704 346-01 – 3 x 6 x 38 mm 3 mm704 346-02 – 3 x 8 x 38 mm 3 mm704 346-03 – 3 x 10 x 38 mm 3 mm704 346-04 – 3 x 13 x 38 mm 3 mm704 346-05 – 4,8 x 12 x 38 mm 3 mm704 346-06 – 6 x 13 x 51 mm 3 mm
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 351 – 2 x 8 x 38 mm 3 mm704 351-01 – 3 x 10 x 38 mm 3 mm704 351-02 – 3 x 13 x 38 mm 3 mm704 351-03 – 3 x 16 x 38 mm 3 mm704 351-04 – 4,8 x 12 x 38 mm 3 mm704 351-05 – 6 x 13 x 51 mm 3 mm
Conical 60° Conical 90°
Type KSV Type KSR
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 348 – 3 x 2 x 28 mm 3 mm
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 349 – 3 x 2 x 38 mm 3 mm
Round nose, conical Flame shaped
Type KEL Type HMB
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 350 – 3 x 10 x 38 mm 3 mm704 350-01 – 3 x 13 x 38 mm 3 mm704 350-02 – 4,8 x 13 x 38 mm 3 mm
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 347 – 3 x 6 x 38 mm 3 mm704 347-01 – 4,8 x 10 x 38 mm 3 mm
Angled, without serrated tip
Type WKN
Art. No. Z3 Art. No. Alu Dimensions* ø Shaft704 352 – 2 x 3 x 38 mm 3 mm704 352-01 – 3 x 3 x 38 mm 3 mm704 352-02 – 4,8 x 4,8 x 38 mm 3 mm704 352-03 – 6 x 6 x 44 mm 3 mm
*Head diameter x head length x overall length
Tools and machines | 961
THE WORK SHOP EXPERTHard metal cutting pins
TK7105
Carbide burr setsHard metal milling pins for aluminium• For processing aluminium, aluminium alloys and non-ferrous metals
• High cutting performance and long lifetime
• Milling pins made of high performance hard metal with alu-teething
• Optimal results in the range from 20 .000 to 25 .000 rpm
• Shaft: 6 mm
Hard metal milling pins for steel• For the processing of rust-free and acid resistant materials
and hardened and not hardened steels
• High cutting performance and long lifetime
• Milling pins of high performance hard metal with cross teething, therefore higher chipping performance
• Optimal results in the range from 20 .000 to 25 .000 rpm
• Shaft: 6 mm
Art No. Shape Size704 324-11 Spherical (for aluminium) 10 x 10 mm704 325-06 Drop shaped (for aluminium) 10 x 16 mm704 322-11 Cylinder shaped (for aluminium) 10 x 20 mm704 323-12 Roller shaped (for aluminium) 10 x 20 mm704 326-07 Semi-circular arch (for aluminium) 10 x 20 mm704 337 Hard metal milling pin set for aluminium, 5 pieces
Art No. Shape Size704 324-03 Spherical (KUD) 10 x 10 mm704 325-02 Drop shaped (TRE) 10 x 16 mm704 322-03 Cylinder shaped (ZYA) 10 x 20 mm704 323-03 Roller shaped (WRC) 10 x 20 mm704 327-01 Flame shaped (HMB) 8 x 20 mm704 335 Hard metal milling pin set for steel, 5 pieces
Carbide burrs for steel• Made of high-performance hard metal
in the best industrial quality
• Ideal for use at high speeds in compressed air precision die grinder (Art . No . 713 062)
• Also suitable for die cutting inner diameters due to the small diameter
• Shaft 3 mm
Art No. Shape Size704 340-02 Cylinder shaped (ZYA) 3 x 13 mm704 342-01 Roller shaped (WRC) 3 x 13 mm704 343-01 Spherical (KUD) 3,2 x 3,2 mm704 344 Drop shaped (TRE) 3 x 6 mm704 345-02 Round arch shape (RBF) 3 x 13 mm704 346-02 Pointed arch shape (SPG) 3 x 8 mm704 347 Flame shaped (HMB) 3 x 6 mm704 350-01 Rounded cone shape (KEL) 3 x 13 mm704 351-02 Pointed cone shape (SKM) 3 x 13 mm704 352-01 Angled (WKN) 3 x 3 mm704 355 Hard metal milling pin set for steel, 10 pieces
Tools and machines | 962
THE WORK SHOP EXPERTHard metal cutting pins
TK7105
Weld spot drill HFB for high-strength and higher strength sheet metals
Group 1 Group 2
Group 3
Weld spot drill HFB VHM-three-flute cutter
VHM-two-flute cutter
Weld spot drill group 1
Weld spot drill group 2
Accessories
Weld spot drill group 3
Art No. Description Dimensions Unit703 489 Solid hard metal three-side cutter for HFB 8,0 x 40 mm 3703 489-1 Solid hard metal three-side cutter for HFB (v)* 8,0 x 44 mm 3703 489-2 Solid hard metal three-side cutter for HFB (v)* 10,0 x 44 mm 3
Art No. Description Dimensions Unit703 489-3 Solid hard metal three-side cutter for HFB 8,0 x 80 mm 3
Art No. Description703 491 Vario-Box for 10 weld point drills „empty“
Art No. Description Dimensions Unit703 485 Weld spot drill HFB 8,0 x 80 mm 10 703 486 Weld spot drill HFB (v)* 8,0 x 44 mm 10 703 488 Weld spot drill for HFB 10,0 x 90 mm 10703 487 Weld spot drill for HFB (v)* 10,0 x 44 mm 10703 492 A Weld spot drill for HFB 12,0 x 80 mm 10703 493 A Weld spot drill for HFB (v)* 12 .0 x 44 mm 10
*v = Vario
*v = Vario
Many vehicles are equipped with body parts made of high-strength steel e .g . “TRIP steel”, BTR, BOR or USIBOR produced .
USIBOR . In order to be able to conduct car body maintenance work quickly, safely, and economically according to manufacturer specifications also in the future, we recommend our weld spot drill for HFB for drilling open these weld spots on higher strength car body parts .
• Special alloy, specially coated
• Drills are milled from a solid material and then grinded
• Extreme toughness and hardness guarantee long service lives
• Precision grinding for maximum cutting speed
• Constructive intricacies of the spot weld drill for HFB creates easier operation
Tools and machines | 963
THE WORK SHOP EXPERTWeld point drill
TK7105
The step on the drill tip acts as a drill stop and indicates the exact drilling depth
Drill bit milled and ground from one solid piece of material
Optimised tip geometry for a long service life
HFB weld spot drill bit Plus For high-strength sheet metal
Qualities:• For the fast and precise drilling of spot welds for bodywork
repairs
• The optimised tip geometry and the special cobalt alloy ensure a long service life
• No centre-marking needed thanks to a fixed centring tip .
• The step on the drill tip acts as a drill stop and indicates the exact drilling depth
• Accidental drilling through the second sheet is prevented
• Angled drilling motion noticeable due to one-sided contact of step with metal
• Corrections can be performed easily
• Recommended speed: 600-670 rpm
Art No. Description Size ø Length Unit703 496 HFB weld spot drill bit Plus 8,0/5,5 mm 80 mm 5703 497 HFB weld spot drill bit Plus 10,0/7,4 mm 90 mm 5
• Fixed centring tip, no centre-marking• Milled and ground from one solid piece of
material • Long service life thanks to the optimised
tip geometry and special cobalt alloy
Tools and machines | 964
THE WORK SHOP EXPERTWeld point drill
TK7105
➀
➀
➁
➁
➂
➂
Solid carbide drills and routers Fo compressed air spot weld remover • To remove, cut and mill spot welds and rivets on high-strength and ultra-strength body steels such as BOR-BTR, BORON, ZSTE, and TRIP steel
Solid carbide drills Z4 4 cutting surfaces, solid carbide soldered on HSS support (shaft)• Length 44,0 mm
• Shaft ø 8 mm
Extension VD 305 Weld spot cutter extension for spot weld remover - length 305 mm• Free-wheeling hand guiding ensures precise and safe use
• Time saving - expensive disassembly work can be saved
• Paint-preserving - the extension VD 305 can be stabilised directly on painted surfaces
Art No. Description Size øWS 627 020 Solid carbide drills Z4 8 mmWS 627 021 Solid carbide drills Z4 9 mmWS 627 022 Solid carbide drills Z4 10 mm
Art No. DescriptionWS 608 012 Extension VD 305
Solid carbide drills Z3 Solid carbide soldered on HSS support (shaft)• 3 cutting surfaces
• Length 49 .0 mm
• Shaft ø 8 mm
Variantic routers• 3 Cutting surfaces
• Long service life
• Sharper than conventional cutters
• Length 44,0 mm
Drill bit NK-2F• Diameter 6 .7 mm
• Length 44,0 mm
Punch
Art No. Description Size øWS 627 010 Solid carbide drills Z3 6,70 mm
Art No. Description Size øWS 620 200 Variantic routers 8 mm
Art No. DescriptionWS 627 001 Drill bit NK-2F
Art No. DescriptionWS 628 005 Punch with centering aid
Tools and machines | 965
THE WORK SHOP EXPERTWeld point drill
TK7105
Stone and concrete drill• The specialist for hardest stone
• Extremely robust percussion drill for highest strain
• Very high drill performance and lifetime due to hammer drill head construction
• Hammer solid, ideal for drill hammer with drill chuck mounting
• Specially alloyed steel quality
• Diamond cut hard metal cutting edge, full embedded up to ø 14 mm
• Low-tension welding technology at over +1100 °C
• Shaft version: cylindrical; up to shaft-ø max . 12 .7 mm
Areas of use:• Useable in percussion drills and drill hammers with
drill chuck mounting
• For granite, walls, natural stone
Art No. Description705 066 Stone and concrete drill set, ø = 4, 5, 6, 8, 10 mm
Art No. Size ø Working length Overall length705 047 4,0 mm 40 mm 75 mm705 048 4,5 mm 40 mm 85 mm705 049 5,0 mm 50 mm 85 mm705 051 6,0 mm 60 mm 100 mm705 054 8,0 mm 80 mm 120 mm705 057 10,0 mm 80 mm 120 mm705 059 12,0 mm 90 mm 150 mm
Weld spot drill HSS-E• Extra stable construction for robust drilling conditions
• Especially adequate for drilling out weld points
• Graining of the weld point is omitted
• Construction according to DIN 1414, cylinder shaft, clockwise cutting
• Construction length according to DIN 1897
• Special cut with centre point, similar to DIN 1412, Form E
• For drilling steel sheets, brass sheets, aluminium, zinc sheets, copper sheets, as well as plastic sheets
Art No. Description Dimensions Unit703 476 Weld spot drill HSS-E bare 6 .0 x 66 mm polished 10703 477 Spot weld drill HSS-E polished 8 .0 x 79 mm polished 10703 481 Spot weld drill HSS-E polished 8,0 x 40 mm blank (v) 10703 483 Weld spot drill HSS-E bare 8 .0 x 44 mm polished (v) 10703 484 Spot weld drill HSS-E polished 10 .0 x 88 mm polished 10703 478 Weld spot drill HSS-E TIN 6 .0 x 66 mm TIN 10703 479 Spot weld drill HSS-E TIN 8 .0 x 79 mm TIN 10703 480 Spot weld drill HSS-E TIN 8 .0 x 40 mm TIN (v) 10703 482 Weld spot drill HSS-E TIN 8 .0 x 44 mm TIN (v) 10703 491 Vario-Box for 10 weld point drills „empty“ 1
*v = Vario
Accessories weld point drill
High grade steel cutting paste
High grade steel cleaner-spray
Art No. Description Contents903 030 Stainless steel cutting paste 60 g
Art No. Description Contents840 004 Stainless steel spray 500 ml
Tools and machines | 966
THE WORK SHOP EXPERTWeld point drill
TK7105
Art No. Description Length705 250 Drill bit box SDS-Plus hammer drill „Trimax“ 5,0 – 12,0 mm
Art No. Size ø Working length Overall length Unit705 250 5110 5,0 mm 50 mm 110 mm 1705 250 6210 6,0 mm 150 mm 210 mm 1705 250 6260 6,0 mm 200 mm 260 mm 1705 250 6310 6,0 mm 250 mm 310 mm 1705 250 7160 7,0 mm 100 mm 160 mm 1705 250 7210 7,0 mm 150 mm 210 mm 1705 250 8110 8,0 mm 50 mm 110 mm 1705 250 8260 8,0 mm 200 mm 260 mm 1705 250 8310 8,0 mm 250 mm 310 mm 1705 250 8450 8,0 mm 400 mm 450 mm 1705 251 0260 10,0 mm 200 mm 260 mm 1705 251 0310 10,0 mm 250 mm 310 mm 1705 251 0460 10,0 mm 400 mm 460 mm 1705 251 0600 10,0 mm 550 mm 600 mm 1705 251 2260 12,0 mm 200 mm 260 mm 1705 251 2310 12,0 mm 250 mm 310 mm 1705 251 2450 12,0 mm 400 mm 450 mm 1705 251 2600 12,0 mm 550 mm 600 mm 1705 251 4200 14,0 mm 150 mm 200 mm 1705 251 4300 14,0 mm 250 mm 300 mm 1705 251 4450 14,0 mm 400 mm 450 mm 1705 251 4600 14,0 mm 550 mm 600 mm 1705 251 5250 15,0 mm 200 mm 250 mm 1705 251 6200 16,0 mm 150 mm 200 mm 1705 251 6250 16,0 mm 200 mm 250 mm 1705 251 6450 16,0 mm 400 mm 450 mm 1705 251 6600 16,0 mm 550 mm 600 mm 1
• Extremely fast drilling speed due to specially designed broad flute and wide drill bit head
• Optimum and rapid removal rate afforded by sturdy drill core
• Perfect transport of drill dust thanks to the large-volume cutting flutes in the drill bit head
Perfect start-up due to two-point centering
tip and recess Extremely long lifetime due to wide carbide edges
Longer service life due to chiselled edge
throughout
Completely smooth drilling due to winged cutting elements
Excellent drilling progress due to reduced line of contact
Heavy-weight concrete
Ytong
Pre-stressed concrete
Bricks
Reinforced concrete
Autoclaved cel-lular concrete
Asphalt concrete
Marble
Sand-lime brick
Granite
Drill bit box SDS-Plus Hammer drill „Trimax“
Perfect transport of drill dust thanks to large-volume flutes in the drill bit head
Improved drilling progressdue to uniform flute cross-section
Sturdy and low-vibrationdue to wide flutesEspecially durable drill bit head
thanks to fully embedded cutting element Better and faster removal rate
due to sturdy drill core
Highest speed thanks to large-volume transport flute
Tools and machines | 967
THE WORK SHOP EXPERTStone drill
TK7105
Hammer drill SDS-Plus• 4-fold-spiral for ideal drilling swarf transport • S4-spiral with large drilling swarf volume
for best transport performance • Centering point for exact pre-drilling
and precise guidance • High wear-resistance due to
tenacious and sharp hard metal • Highest stability due to core reinforcement,
therefore maximum energy transmission • Environment-friendly surface technology
Areas of use:• In hammer drills with SDS-plus-mounting and
25-bolt-mounting Hilti TE 10-22
• For granite, walls, natural stone
Art No. Size ø Working length Overall length Unit705 200 4,0 mm 50 mm 115 mm 20 pcs .705 201 5,0 mm 50 mm 115 mm 20 pcs .705 202 5,0 mm 100 mm 165 mm 20 pcs .705 203 6,0 mm 50 mm 115 mm 20 pcs .705 204 6,0 mm 100 mm 165 mm 20 pcs .705 205 6,0 mm 150 mm 215 mm 20 pcs .705 206 6,0 mm 200 mm 265 mm 20 pcs .705 207 6,5 mm 100 mm 165 mm 20 pcs .705 208 7,0 mm 50 mm 115 mm 20 pcs .705 209 8,0 mm 50 mm 115 mm 20 pcs .705 210 8,0 mm 100 mm 165 mm 20 pcs .705 211 8,0 mm 150 mm 215 mm 20 pcs .705 212 8,0 mm 200 mm 265 mm 20 pcs .705 213 10,0 mm 50 mm 115 mm 20 pcs .705 214 10,0 mm 100 mm 165 mm 20 pcs .705 215 10,0 mm 150 mm 215 mm 20 pcs .705 216 10,0 mm 200 mm 265 mm 20 pcs .705 217 10,0 mm 250 mm 315 mm 20 pcs .705 218 10,0 mm 300 mm 350 mm 1 pc .705 219 10,0 mm 400 mm 455 mm 20 pcs .705 220 12,0 mm 100 mm 165 mm 20 pcs .705 221 12,0 mm 150 mm 215 mm 20 pcs .705 222 12,0 mm 200 mm 265 mm 20 pcs .705 223 12,0 mm 400 mm 465 mm 10 pcs .705 224 12,0 mm 550 mm 615 mm 10 pcs .705 225 12,0 mm 950 mm 1005 mm 10 pcs .705 226 14,0 mm 100 mm 165 mm 10 pcs .705 227 14,0 mm 150 mm 215 mm 10 pcs .705 228 14,0 mm 200 mm 265 mm 10 pcs .705 229 14,0 mm 250 mm 315 mm 10 pcs .705 230 14,0 mm 400 mm 465 mm 1 pc .705 231 16,0 mm 400 mm 465 mm 1 pc .705 232 18,0 mm 250 mm 300 mm 1 pc .705 233 18,0 mm 400 mm 450 mm 1 pc .705 234 20,0 mm 250 mm 300 mm 1 pc .705 235 20,0 mm 400 mm 450 mm 1 pc .705 236 20,0 mm 950 mm 1000 mm 1 pc .705 237 22,0 mm 950 mm 1000 mm 1 pc .
Active centering tip• For active cutting in concrete
• High stability and precision
Toothed carbide cutters• Special V-design crushes concrete
into the finest powder
• Faster removal of drilling waste
4-spiral turbo-design• Consistently high removal rate
of drilling waste
• Reduces unwanted dust explosions
Drilling without the hassle of stalling and jamming due to the combination of innovative drill head and large-volume spiral shape.
Tools and machines | 968
THE WORK SHOP EXPERTStone drill
TK7105
Wall hammer drill SDS-max• Narrow drill head with 4-fold carbide cutting edges in
X-shaped configuration for fast penetration of even the hardest concrete
• Large-volume double-helix spiral flute for rapid drilling dust removal, from ø 25 mm with vario gradient
• Core reinforced for full power transmission
• Extremely fast, extremely long lifetime
• No catching, no risk of breaking when reinforcement is hit
• Runs extremely smoothly with significantly reduced vibrations, which relieve the operator and protect the machine
• High-precision drill holes
• Vacuum-welding/hardening process
Areas of use:• Fitting in hammer drills with SDS-Max-mounting
and Hilti hammer drills
• For granite, walls, natural stone
• Plastic hanger (PP) with Hafteti and Euro hole
Art No. Size ø Working length Overall length705 300 18,0 mm 400 mm 540 mm705 302 20,0 mm 200 mm 320 mm705 303 20,0 mm 400 mm 520 mm705 304 20,0 mm 800 mm 920 mm705 306 22,0 mm 400 mm 520 mm705 307 24,0 mm 400 mm 520 mm705 308 25,0 mm 200 mm 320 mm705 309 25,0 mm 400 mm 520 mm705 311 30,0 mm 450 mm 570 mm705 313 32,0 mm 450 mm 570 mm705 316 40,0 mm 450 mm 570 mm705 317 40,0 mm 800 mm 920 mm
Multi-cutter drill head Chisel plate flanked by two additional cutters for a very silent operation and constant drill hole geometry at best rate of advance
4-fold wide turn Best possible drilling progress thanks to optimised drilling dust dissipation via four real drill flutes
Core reinforcement For optimum impact energy transfer and fracture stability
Optimised mounting shaft Perfect fit and optimal power transfer of the machine to the drill
Tools and machines | 969
THE WORK SHOP EXPERTStone drill
TK7105
Roof-tile and fine-stoneware drill
Qualities:• Precise, nick-free bores without unsightly chipped edges
• Long service life due to optimum removal of drilling dust
• No percussive drilling – pre-drilling not required! Ideal for all cordless screwdri-vers at low speed
Areas of use:• Hard-burned and glazed roof tiles, tilers and natural stone setters, heating and
plumbing installation, electrical installation, kitchen and bathroom furniture construction
Art No. Size ø Working length Length Unit705 400 0400 4,00 mm 45 mm 80 mm 5705 400 0500 5,00 mm 50 mm 90 mm 5705 400 0600 6,00 mm 60 mm 100 mm 5705 400 0800 8,00 mm 70 mm 120 mm 5705 400 1000 10,00 mm 70 mm 120 mm 5
• The ideal drill for hard materials• Pressure-free operation
due to diamond-ground carbide tip
• Better centring thanks to tetrahedral, ground carbide tipping
Tools and machines | 970
THE WORK SHOP EXPERTStone drill
TK7105
SDS-Max chisel• Quality for highest demands
• Chisels are made of high-quality special steel, and have wear-resistant, shot-peened surface
• High erosion performance due to ideal weight distribution
Areas of use:• For granite, walls, natural stone
• A novelty cutting edge geometry of the flat chisel increases the erosion performance by 15 % and allows you to work quicker
• The three-cutting edge geometry prevents deadlocking
SDS-Plus chisel• Quality for highest demands
• Chisels are made of high-quality special steel, and have wear-resistant, shot-peened surface
• High erosion performance due to ideal weight distribution
Areas of use:• For granite, walls, natural stone
• A novelty cutting edge geometry of the flat chisel increases the erosion performance by 15 % and allows you to work quicker
• The three-cutting edge geometry prevents deadlocking
Art No. Description Width Working length705 318 SDS-Max point chisel 400 mm705 318-1 SDS-Max point chisel 600 mm705 319 SDS-Max flat chisel 25 mm 400 mm705 319-1 SDS-Max flat chisel 25 mm 600 mm705 320 SDS-Max spade chisel 50 mm 400 mm705 321 SDS-Max spade chisel 80 mm 300 mm705 322 SDS-Max spade chisel 115 mm 350 mm
Art No. Description Width Working length705 238 SDS-Plus point chisel 250 mm705 239 SDS-Plus flat chisel 25 mm 250 mm705 240 SDS-Plus spade chisel 40 mm 250 mm705 241 SDS-Plus spade chisel 60 mm 250 mm705 242 SDS-Plus tile chisel 40 mm 260 mm
SDS-Max point chisel SDS-Plus point chisel
SDS-Max flat chisel SDS-Plus flat chisel
SDS-Max spade chisel SDS-Plus spade chisel
SDS-Plus tile chisel
Tools and machines | 971
THE WORK SHOP EXPERTStone drill
TK7105
0
20
40
60
80
100
120
ø 12 mm ø 20 mm ø 30 mm
Core hole drill assortment• Enormous cost and time saving, as the core hole drill only cuts
one ring, and not the entire drill diameter
• No elaborate preparation work like centering, predrilling and drilling open
• Up to 10times shorter drilling time of hole drills compared to spiral drills
• Significantly higher lifetime of hole drills due to the lower material strain and the lower wear
• Significantly less energy consumption, as spiral drills need higher force effort and a higher drive performance
HSS-core drill Spiral drill HSS DIN 345
Drilling time comparison between HSS-core drill / Spiral drill HSS DIN 345
Work piece: Steel beam; drilling depth: 12 mm . Holes were drilled into the full material without pre-drilling, generally, no cooling or lubrication was used .
Chipping volumeCore dill Spiral drill
The cutting edge is decisive ...• Significantly higher cutting performance due to an improved and developed
cutting edge geometry and associated cutting behaviour
• Increased cutting performance and less cutting force through optimised cutting edges
• For the universal use in different steel kinds through the optimised chipping angle
• Lower thermal strain of the HSS-core drill through the special geometry of the column, which leads the warmth generated during the drilling process away with the chips to a great extent
• Optimised, spiral-shaped guidance fibres fir a lower friction between the HSS-core drill and the work piece
Tools and machines | 972
THE WORK SHOP EXPERTCore hole drill assortment
TK7105
Art. No. Ø mm Ø Weldon shaft
Overall length Number of teeth
Cutting depth
703 662 0014 14 mm 19 mm 63 mm 4 30 mm703 662 0015 15 mm 19 mm 63 mm 4 30 mm703 662 0016 16 mm 19 mm 63 mm 6 30 mm703 662 0017 17 mm 19 mm 63 mm 6 30 mm703 662 0018 18 mm 19 mm 63 mm 6 30 mm703 662 0019 19 mm 19 mm 63 mm 6 30 mm703 662 0020 20 mm 19 mm 63 mm 6 30 mm703 662 0021 21 mm 19 mm 63 mm 6 30 mm703 662 0022 22 mm 19 mm 63 mm 6 30 mm703 662 0023 23 mm 19 mm 63 mm 6 30 mm703 662 0024 24 mm 19 mm 63 mm 6 30 mm703 662 0025 25 mm 19 mm 63 mm 6 30 mm703 662 0026 26 mm 19 mm 63 mm 8 30 mm703 662 0027 27 mm 19 mm 63 mm 8 30 mm703 662 0028 28 mm 19 mm 63 mm 8 30 mm703 662 0029 29 mm 19 mm 63 mm 8 30 mm703 662 0030 30 mm 19 mm 63 mm 8 30 mm703 662 0031 31 mm 19 mm 63 mm 8 30 mm703 662 0032 32 mm 19 mm 63 mm 10 30 mm703 662 0033 33 mm 19 mm 63 mm 10 30 mm703 662 0034 34 mm 19 mm 63 mm 10 30 mm703 662 0035 35 mm 19 mm 63 mm 10 30 mm703 662 0036 36 mm 19 mm 63 mm 10 30 mm703 662 0040 40 mm 19 mm 63 mm 10 30 mm703 662 0045 45 mm 19 mm 63 mm 10 30 mm703 662 0050 50 mm 19 mm 63 mm 12 30 mm703 662 0055 55 mm 19 mm 63 mm 12 30 mm703 662 0060 60 mm 19 mm 63 mm 12 30 mm
HSS-core drill with Weldon shaft• Core drill made of high performance quick working steel
• Cutting geometry of the core drill allows a quick chip removal towards the top
• Spring mounted guidance pin helps to loosen the cut out pieces
• Centre-punching and pre-drilling are omitted
Areas of use:• Adequate for steel
(e .g . T-carriers, large-format sheet metals), steel cast, colour and lightweight metals
Application:• Insert guidance pin into the core drill
• Insert hole drill into the mounting and tighten the hex key screws, pay attention to the clean position of the hole drilling the mounting container
• In the SimTEC fast clamp intake the core drill is automatically locked
HSS-full drill with Weldon shaft• Spirally grooved cutting edge geometry prevents the breaking danger
of the cutting edges in case of overload or deadlock of the cuts
• Extremely high stability of the full drill provides a significantly increased lifetime
• No centre-marking and tearing due to exact drilling
• HSS Full drill allows easier regrinding compared to core drills of the same diameter
Art. No. Ø mmØ Weldon
shaftOverall length
Cutting depth
703 661 0010 10 mm 19 mm 64 mm 30 mm703 661 0011 11 mm 19 mm 64 mm 30 mm703 661 0012 12 mm 19 mm 64 mm 30 mm703 661 0013 13 mm 19 mm 64 mm 30 mm
Tools and machines | 973
THE WORK SHOP EXPERTCore hole drill assortment
TK7105
HSS core drill set with Weldon shaft, 10-piece• Core drill made of high performance quick working steel
• Cutting geometry of the core drill allows a quick chip removal towards the top
• Spring mounted guidance pin helps to loosen the cut out pieces
• Centre-punching and pre-drilling are omitted
Optional accessories• HSS Core hole drill with Weldon shaft (3/4"), 8 Core drills (Cutting depth 30 mm)
in the diameters: 12 mm, 14 mm, 16 mm, 18 mm, 20 mm, 22 mm, 24 mm, 26 mm
• 1 Cutting spray, 50 ml
• 1 Guidance pin ø 6 .35 x 77 mm for cutting depth 30 mm
Art No. Description Contents703 664 HSS core drill set 10 pcs .
HSS core drill set with Weldon shaft, 7-piece• Core drill made of high performance quick working steel
• Cutting geometry of the core drill allows a quick chip removal towards the top
• Spring mounted guidance pin helps to loosen the cut out pieces
• Centre-punching and pre-drilling are omitted
Optional accessories• HSS Core hole drill with Weldon shaft (3/4"),
6 Core drills (Cutting depth 30 mm) in the diameters: 12 mm, 14 mm, 16 mm, 18 mm, 20 mm, 22 mm, 24 mm, 26 mm
• 1 Guidance pin ø 6 .35 x 77 mm for cutting depth 30 mm
Art No. Description Contents703 663 HSS core drill set 7 pcs .
Mounting shaft for core hole drills with Weldon shaft
• Delivery scope including cooling agent flask
Centering tip for core drills
Art No. Description Size703 681 Mounting shaft for core drill MK 2703 682 Mounting shaft for core drill MK 3703 679 Centering tip for core drills 6,35 x 77 mm
Art No. Description Size703 679 Centering tip for core drills 6,35 x 77 mm703 680 Centering tip for core drills 6,35 x 102 mm
Tools and machines | 974
THE WORK SHOP EXPERTCore hole drill assortment
TK7105
Pipe clamp device for magnet box column drills • Enables the use of magnet box column drills
on pipes from 50 to 500 mm diameter
• Pipe clamping device only useable horizontally
Technical specifications:Length: 220 mm
Width 130 mm
Height: 28 mm
Lashing strap: 2 m
Weight: 4 .4kg
Tightening means: Ratchet
Art No. Description703 684 Pipe clamping device for magnet box column drills
Adapter for core drills „Quick In“ - „Weldon“
• Adapter enables the use of drills with „Weldon“-shaft in drills with „Quick In“ mounting (e . g . KBM 32 from the company Fein)
Art No. Description Size703 674 Adapter for core drill „Quick In - Weldon“ 703 680 Centering tip for core drills 6,35 x 102 mm
Tools and machines | 975
THE WORK SHOP EXPERTCore hole drill assortment
TK7105
Automatic fast clamping intake “SimTEC” for core drills with Weldon shaftThe quick-change chuck “SimTEC” allows fast replacement of tools without the need for special tools .
One-handed operation .
1 . Push the lock ring up until it sits firmly in place .
2 . Place the core drill into the “SimTEC” chuck . It locks
into place with a loud click . The lock ring snaps back down .
3 . The core drill is inserted in the “SimTEC” chuck .
The machine is now ready for use .
4 . To release the coe drill, the lock ring must be
pushed up .5 .
Caution, the core drill will fall out of the “SimTEC” chuck .
Quick fastening mounting „SimTEC“ for core drills with Weldon shaft• Enables a very quick tool change without additional tools
Art. No. Description Machine’s chuck Suitable for model Ø Core drill Cutting depth core drill
703 677 Quick change chuck mount „SimTEC“ MT 2 shaft TX 920 10 – 60 mm 30 mm/50 mm703 678 Quick change chuck mount „SimTEC“ MT 3 shaft TX 930 10 – 60 mm 30 mm/50 mm
Tools and machines | 976
THE WORK SHOP EXPERTCore hole drill assortment
TK7105
282,0250,0 182,0
417,
0
Magnet box column drill machine RS 25eQualities:• Long service life thanks to internal wiring - soiling or damage is no longer possible!
• Powerful motor for core drill up to Ø 60 .0 mm
• The adhesion of the magnet is reinforced by manually adjustable additional support
• 2-speed gearbox with hardened precision gears to be operated via ergonomic rotary switch knob
• Ergonomic positioning of the motor and magnet switch
• Infinitely variable speed controller through which cutting speed can be optimally adjusted
• Forward / reverse switchable for thread cutting up to M 20
Included in delivery:• Plastic carrying case
• Expelling wedge
• Safety belt
• Drill chuck: 3 – 16 mm
• Taper thorn MK2/B16
• Coolant bottle + holder
• Mounting bracket
Technical specifications:Magnetic holding force: 13,000 N
Power consumption: 1,200 Watt
Gears: 2 Gang
Rotational speed: 100 to 250 / 180 to 450 rpm
Speed controller: yes
Power controller: no
Forward/reverse operation: yes
Height: 408 to 598 mm
Footprint: 190 x 90 mm
Weight: 18 kg
Hub: 190 mm
Seating: Morse taper MT 2
Core drill: ø 12 to 60 mm
Drill chuck: 3 to 16 mm
Twist drill DIN 338: max . ø 130 mm
Twist drill DIN 1897: max . ø 16 mm
Twist drill DIN 345: max . ø 20 mm
Core drill cutting depth: 30/55 mm
Supply voltage: 220 to 240 V
corresponding to: VDE, CEE
Relocatability: no
Swivel range: no
Thread cutting: yes
Art No. DescriptionG 702 098 Magnet box column drill machine
THE WORK SHOP EXPERTCore hole drill assortment
TK7105
Overview of magnet box columns drill machine RS25e
Magnet box column drill machine Art . No . G 702 098
Pipe clamp device Art . No . 703 684
Adapter from Weldon on „Quick-In“
Art . No . 703 674
Mounting shaft from MK 2 to Weldon
Art . No . 703 681
Quick change chuck mount „SimTEC“ from MK 2 to Weldon
Art . No . 703 677
Drill chuck mount with morse taper, MK 2
Art . No . G 703 008
Centering tip for HSS core drill Length:
102 mm Art . No . 703 680
Centering tip for HSS core drill Length:
77 mm Art . No . 703 679
Morse taper drill HSS DIN 345, MK 2
Art . No . . 703 700-703 717
Keyless drill chuck 0 .5-13 mm
Item no . G 703 006Keyless drill chuck
1 .5-16 mm Item no . G 703 007
HSS core drill with 14-60 mm Weldon shaft max . drill depth 30 mm Art . No . 703 662-0014 bis -0036, -0040, -0045, -0050, -0055,
-0060
For example suitable for core drill machine „KBM 32“ from the manufacturer Fein .
„Quick In“ system
Special metal drill SAS-Plus, C-HSS
Art . No . 703 501 0100–703 501 1300
HSS-solid drill with Weldon shaft 10-13
mm Art . No . 703 661-0010 bis -0013
Tools and machines | 978
THE WORK SHOP EXPERTCore hole drill assortment
TK7105