Tohnichi Maintenance of Torque Tools
-
Upload
leire-meiga -
Category
Documents
-
view
247 -
download
0
Transcript of Tohnichi Maintenance of Torque Tools
-
7/25/2019 Tohnichi Maintenance of Torque Tools
1/24
TECHNICAL DATA
7. Maintenance of Torque Tools
7-1. Adjustment Methods
(1)Adjustment methods for torque tools 88
(2)Adjustment of adjustable type torque screwdrivers
89
7-2. Procedure for Disassembly, Reassembly andTorque Adjustment
(1)QL model
90
(2)QSP3 model 94
(3)SP, QSP (6N, 12N, 420N)models 98
(4)DB model 100
7-3. Parts List(1)QL model 102
(2)DB model 104
7-4. Cross-section DrawingsCross-section drawings 106
86 TOHNICHI TORQUE HANDBOOK Vol.7
TECHN
ICALDATA
-
7/25/2019 Tohnichi Maintenance of Torque Tools
2/24
7
About adjusting and special tools
Used for torque adjustment (zero
point) of LTD / RTD models
Used for torque adjustment or disassembly
of preset type torque wrenches
Maintenance of torque tools needs
in-depth understanding about their
structure and methods of torque
adjustment and repair. For learning
adjustment or repair methods, consultTohnichi or nearest distributors. Adjusting tool for LTD / RTD models Thrustring tool for SP models
Used for torque adjustment of QSP3
/ QSP4 models
Adjusting tool for QSP3 models
Used for torque adjustment of dial indicating
type torque wrenches as well as T-type and
DOT models
Adjusting tool for DB models
87Technical Data
-
7/25/2019 Tohnichi Maintenance of Torque Tools
3/24
Chapter
Adjusting procedures for adjustable type torque tools
(1)Set the torque tool to the minimum scale value.(2)Correct the value to the minimum scale value with the torque tester (zero point
correction, parallel shift ).(3)Set the value of the torque tool to the maximum scale value.(4)Adjust the value to the maximum scale value with a torque tester (gain adjustment,
multiplying shift ).(5)Conrm the value adjustment by repeating procedures (1)-(4).
Adjusting procedures for indicating type torque tools
(1)Correct the value of the torque tool to the zero point. (zero point correction, parallel shift ).(2)Load the torque tool with the maximum torque value using the torque tester and read the
scale value.(3)Release the load and correct the value by adjustment (gain adjustment, multiplying shift ).(4)Conrm the adjusted value by repeating procedures (1)-(3).
Torque wrenches that do not have adjusting devices are not adjustable.
TECHNICAL DATA
Maintenance of Torque Tools
(1)Adjustment methodsfor torque tools
Zero point correction
Gain adjustment
Central point
For a graduated torque measuring tool, coordinate the scale torque value with themeasured torque value by repeating the zero point correction and the gain adjustmentseveral times. (Figure 7-1)
For the zero point correction (Figure 7-1), the scale values are increased or reducedby the same quantity (
)against the measured torque values. Zero point correction isusually made at the zero point or at the minimum scale value.
For the gain adjustment (Figure 7-1), the scale values are magnied or reduced almostproportionally to the measured torque values at a certain rate (
). Gain adjustment isusually made at the maximum scale value.
If the error at the central point of the full-scale span is too large, carry out the abovezero-point correction and gain adjustment at the points that have deviated from thezero point and the maximum scale value, respectively. If the error is still too large evenafter the procedure, the torque tool must be disassembled and repaired.
7-1
7-1. Adjustment Methods
Figure 7-1. Adjustment fgure
Table 7-1. Torque tool zero-point correction and gain adjustment locations
Type Model Name Zero Point Correction Gain Adjustment
Beam type torque wrench SF, F, QF, CF Needle bending Scale plate replacement
Dial indicating torque wrench DB, DBE,T Dial rotation Dial lever
Adjustable torque wrench QL, PQL, QLE, CL, CLESupplemental graduation
replacementCorrecting screw
Dial indicating torque
screwdriverFTD, FTD-S
Needle or spring bracket
rotation
Vertical movement of
spring seat
Adjustable torque screwdriverLTD, RTD, AMLD, Zero adjusting screw or Correcting screw
BMLD, AMRD, BMRD shim
Power torque tool U, ME, AME, AP, AUR, DCME Scale ring Torque adjusting screw
M
easuredtorque
Torque shown on the scale
Correctly
adjusted line
88
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
4/24
Maintenance of Torque Tools Chapter 7-1
Table 7-2. Adjustment of adjustable type torque screwdrivers (LTD, RTD)
Model
Gain adjustment Zero point adjustment Adjusting tool
Rate of torque change (V)
[cNm/rev]Rate of torque change ( I )
[cNm/rev]Remarks Catalog No.
RTD15CN / LTD 9 0.8
Zero adjusting screw
1 rev
51
RTD30CN / LTD 17.8 1.6 46
RTD60CN / LTD 42 4.2 47
RTD120CN / LTD 70 10 48
RTD260CN / LTD 154 10 49
RTD500CN / LTD 322 33.3
LTD1000CN 654 66.650
LTD2000CN 1120 67.0(t =0.1[mm])
Shim adjustmentt = 0.1 , t = 0.2 , t = 0.5
(2)Adjustment of adjustable type torque screwdrivers
Figure 7-2. Detailed illustration of parts during adjustment
Adjustment method for adjustable type torque screwdrivers
(1)Loosen the set screw.(2)Match the scale to the minimum scale value, set the tool
on a tester, and measure the operating torque.(3)Turn the zero adjusting screw to match the scale value
with the actual measured value.
In the case where the actual measured value is lower
than the scale value, turn the zero adjusting screwclockwise (CW).
In the case where the actual measured value is higher
than the scale value, turn the zero adjusting screw
counterclockwise(CCW).
Note: The zero adjusting screw should be turned while
the gain correcting screw is in the tightened condition.(4)Match the scale to the maximum scale value, set the tool
on the tester, and measure the operating torque.(5)Turn the gain correcting screw to match the scale value
with the actual measured value.
In the case where the actual measured value is lowerthan the scale value, turn the gain correcting screw
counterclockwise (CCW).
In the case where the actual measured value is higher
than the scale value, turn the gain correcting screw
clockwise (CW).
Note: The gain correcting screw should be turned while
the zero adjusting screw is in the tightened condition.(6)Repeat procedures (3)to (5)to repeat the adjustment
until both the minimum value and maximum value are
within the accuracy range.
(7)Tighten the set screw, and reconfrm the operatingtorque at each measurement point.
Adjusting tool
Slotted (minus) screwdriver
Zero-adjusting screw
Gain correcting screw
Set screw
Torque screwdriver
T T0
IAmount of torque changeSince 360 0.5 = 180,you are required to turn thezero adjusting screw 0.5turn (180)clockwise.
Number of turns ofthezero adjusting screw
Set torque T 60cNm
Measured torque T0 55cNm
60 55 = 0.5
10
=
Since 360 0.13 = 47, youare required to turn the gaincorrecting screw 0.13 turn (47)counterclockwise.
Number of counterclockwise
turns of the gain correcting screw
T T0
VAmount of torque change
Set torque T 260cNm
Measured torque T0 280cNm
260 280
= 0.13 154
=
89Technical Data
MaintenanceofT
orqueTools
-
7/25/2019 Tohnichi Maintenance of Torque Tools
5/24
Chapter
TECHNICAL DATA
7-2
7-2. Procedure for Disassembly, Reassembly and Torque Adjustment(1)QL model
ADisassembling
Figure 7-3.
Exploded view
a) Disassembling the head part(1) Loosen the locker, and turn the supplemental graduation
counterclockwise to reduce it to the minimum value.(2)Pull out the head pin from the tube by removing the calking
with a fle or grinder and tapping the pin with a punch.(3)Pull out the head assembly from the tube. At this time, the
toggle, thruster, and roller, which are connected to the head end
part by the toggle pins, are also removed from the tube.(4)When the two toggle pins are removed, the head assembly can
be separated into the head, toggle, thruster and roller.
b) Disassembling the ratchet part(1)Remove the flat head screw (Phillips or hexagonal), using a
Phillips (plus) screwdriver or hexagon key.(2)Remove the head cover from the head and ratchet.(3)Remove the ratchet assembly.(4)Take out the ratchet springs. (Be careful that the ratchet
springs do not spring out.)(5)Remove the head saws.
c) Disassembling the supplemental graduation,
graduation scale, and main spring parts(1)Remove the spring pin using pliers.(2)Remove the locker and washer by rotating it counterclockwise.(3)Remove the supplemental graduation and the supplemental
graduation seat.(4)Loosen the thrust ring screw with a hexagon key.(5)Remove the thrust ring by turning it counterclockwise with the
thrust ring tool.
(6)Pull out the adjusting screw. The scale piece assembly is takenoff at the same time.
(7)Setting the stop plate to face upward, lightly tap on the side of
the tube to remove the stop plate by dropping it inside the tube.(8)Pull out the main spring and the seat.
Maintenance of Torque Tools
QL4
Spring, main
Scale asembly
Plate, stop
Seat
Ball, steel
Thrustring screw
Seat, sup. graduationRing, thrust
Screw, adjusting
Washer, nylon
Locker
Washer
Spring pin
Sup. graduation
90
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
6/24
a) Reassembling the ratchet part(1) Insert the head saw axis part back into the hole of the head.
(2) Install the ratchet springs between the ratchet and the head
saws so that the springs small diameters are touching the
head saws. (Be careful that the ratchet springs do not springout.)
(3) Insert the ratchet assembly while pressing down on the head saw.
(4) Install the head cover, centering the hole over the ratchet.
(5) Place some screw adhesive on a small plate and apply a small
quantity into the screw hole of the head cover. (Be careful not
to get the adhesive on the inside parts.)
(6) Tighten the fat head screw (Phillips (plus)or hexagon), using a
Phillips screwdriver or hexagon key.
b) Reassembling the main spring part(1) Insert the seat into the tube after applying Evertorque lubricant
(P.407)to the joining surface of the seat inside the tube.
(2) Insert the main spring into the tube.
(3) Assemble the axis part of the stop plate to the hole of the tube
from the inside of the tube. (At this time, the lengthwise
direction of the axis part should be on the supplemental
graduation side.)
(4) Insert the scale assembly, matching the groove of the scale
assembly to the stop plate.
(5) Turn the thrustring clockwise using the thrustring tool and set
the specified position of the supplemental graduation,
rotating it sothat the figures show in the center of thescale window.
(6) Tighten the thrustring screw with the specified torque. (see
P.99 Table 7-5)
(7) Insert the supplemental graduation seat in the supplemental
graduation, matching it with the serrations.
(8) Insert the flat washer into the locker and tighten the locker
lightly by rotating it clockwise. (The pin should be inserted
after the adjustment.)
B: Reassembling
Chapter 7-2
Figure 7-4. Ratchet springposition
Maintenance of Torque Tools
Head saw
Ratchet spring
91Technical Data
MaintenanceofT
orqueTools
-
7/25/2019 Tohnichi Maintenance of Torque Tools
7/24
Chapter
TECHNICAL DATA
Maintenance of Torque Tools
7-2. Procedure for Disassembly, Reassembly and Torque Adjustment
7-2
C: Torque Adjustment
Figure 7-6. Positions of locker and pin
Lock
Unlock (Strike the pin)
c) Reassembling the head part(1)Apply grease to both pits of the head end part and put a steel ball
in each pit, respectively.(2)Attach the toggle with the toggle pin to the groove at the end of the
head and then connect the toggle to the thruster. At this time, apply
adequate Evertorque lubricant to the pin holes.(3)Apply Evertorque lubricant (P.407) to the roller groove part of the
thruster, and insert the roller bushing with the roller pin inserted.(4)Install the head assembly into the tube of part b) by aligning the
square drive with the at part of the tube (or the side with the serial
number) and inserting from the thruster side.(5)Set the tube upright and use the resistance of the table to press
the thruster axis part into the hole of the seat.(6)Insert the head into the tube and insert the head pin by matching it
with the head pin hole and calk it.(7)Confirm that the thruster is in proper contact with the seat by
operating the torque wrench.
(1)Loosen the locker, and turn the supplemental graduation to set it to
the minimum scale value.(2)Set the torque wrench on a tester, apply loading and conrm the
operating torque. Turn the supplemental graduation to match the
actual measured value as the minimum scale value.(3)Remove the spring pin using nippers.(4)Rotate the locker counterclockwise to remove it.
(5)Replace the supplemental graduation so that the 0 of the scale isshown in the scale window.
(6)Attach the locker.(7)Rotate the supplemental graduation clockwise to match the
maximum scale value. Set the torque wrench on the tester, apply
loading and conrm the operating torque.
In the case where the actual measured value is lower than the
scale value, turn the correcting screw counterclockwise (CCW).
In the case where the actual measured value is higher than the
scale value, turn the correcting screw clockwise (CW).Note: The correcting screw should be turned while the torque
wrench is in the operating condition.(8)Repeat procedures (1)to (7)to repeat the adjustment until both the
minimum value and maximum value are within the accuracy range.(9)When both the minimum value and maximum value are within
the accuracy range, tap in the spring pin. The position for tapping
in the spring pin should be where the supplemental graduation
is free to rotate when the locker is loosened, but allowing the
supplemental graduation to be xed when the locker is tightened.
Figure 7-5
Head
Pin, toggle
Pin, toggle
Roller
Toggle
Thruster
Ball, Steel
Ball, Steel
92
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
8/24
Maintenance of Torque Tools Chapter 7-2
Table 7-3. Torque change amount of the QL adjusting screw
ModelAdjusting screw 1 revolution(Maximum value,counterclockwise rotation)
[Nm/rev]
Size ofhexagonsocket
screw key
QL1.5N4 0.2
1.27QL3N4 0.5
QL6N4 0.9
QL12N4 1.9
QL25N 3.4 1.5
QL50N 7.7
2QL100N4 14
QL140N 17
QL200N4 34
2.5QL280N 31
QL420N 39
QLE550N 48
QLE750N 77
3QLE1000N 89
QLE1400N 110
QLE2100N 174 4
Figure 7-7. Detailed illustration for torque set
Window of supplemental graduation
Decrease
Locker
Main graduation Scale line Spring pinSupplemental
graduation
Increase
93Technical Data
MaintenanceofT
orqueTools
-
7/25/2019 Tohnichi Maintenance of Torque Tools
9/24
Chapter
TECHNICAL DATA
(2)QSP3 model
a) Disassembling the head part
(1)Turn the adjusting screw counterclockwise with an adjusting tool to loosen
to the minimum scale point.
(2)Pull out the head pin from the tube by removing the calking with a le or
grinder and tapping the pin with a punch.
(3)Pull out the head assembly from the tube. At this time, the toggle, thruster,
and roller, which are connected to the head part by the toggle pins, are also
removed from the tube.
(4)Remove the two toggle pins to separate the assembly into the head,
toggle and thruster, and also remove the roller from the thruster.
b) Disassembling the ratchet(1)Remove the at head screw (Phillips or hexagonal)using a screwdriver or
hexagon key.
(2) Remove the head cover from the head and ratchet.
(3)Remove the ratchet assembly.
(4)Take out the ratchet springs. (Be careful that the ratchet springs do not
spring out.)
(5)Remove the head saws.
c) Disassemble the main spring part(1)Cut off the adhesive part of the handle by using a utility knife and remove the
rubber handle. (1.5N4 to 140N)
(2)Pull out the cap pin from the tube by removing the calking with a le or
grinder and tapping the pin with a punch. (200N, 280N only)
(3)Remove the cap. (Be careful not to let the steel balls drop out. (200N, 280N
only)
(4)Remove the thrust ring screw.(5)
Remove the thrust ring with rotating the thrust ring tool counterclockwise.
(6)Remove the adjusting screw. At this time the scale piece will also be
removed.
(7)Setting the stop plate to face upward, lightly tap on the side of the tube to
remove the stop plate by dropping it inside of the tube.
(8)Pull out the main spring and the seat while tilting the tube.
ADisassembling
7-2. Procedure for Disassembly, Reassembly and Torque Adjustment
7-2 Maintenance of Torque Tools
QSP3
94
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
10/24
a) Reassembling the ratchet part(1) Insert the head saw axis part back into the hole of the head of the
head.
(2)Install the ratchet springs between the ratchet and the head saws
so that the springs small diameters are touching the head saws. (Be
careful that the ratchet springs do not spring out.)
(3)Insert the ratchet assembly while pressing down on the head saw.(4)Install the head cover, centering the hole over the ratchet.
(5)Place some screw adhesive on a small plate and apply a small quantity
into the hole of the head cover. (Be careful not to get the adhesive on
the inside parts.)
(6)Tighten the flat head screw (Phillips or hexagonal), using a Phillips
(plus)screwdriver or hexagon key.
BReassembling
Chapter 7-2Maintenance of Torque Tools
Head saw
Ratchet spring
Figure 7-8. Ratchet spring position
Figure 7-9
b) Reassembling the main spring parts(1)Insert the seat into the tube after applying Evertorque lubricant (P.407)
to the joining surface of the seat inside the tube.
(2)Insert the main spring to the tube.
(3) Insert the axis part of the stop plate to the hole of the tube from the
inside of the tube. (At this time, the lengthwise direction seen from the
axis part should be on the cap side.)
(4)Insert the scale assembly, matching the groove of the scale assembly to
the stop plate.(5)Turn the thrustring tool clockwise to screw the thrustring into the
specifed position.
(6)Tighten the thrustring screw to the specifed torque. (refer to P.99 Table
7-5)
(7)Insert the supplemental graduation seat inside the rubber handle.(1.5N4
to 140N)
(8)Apply adhesive to the tube, and insert the rubber handle. (1.5N4 to
140N)(9) Matching the cap with the tube hole, insert the cap pin and calk it.
(200N, 280N)Seat
Spring, main
Cap
Rubber handle
Piece, scale
Plate, stop
Thrustring
Ball, steel
Washer, nylon
95Technical Data
MaintenanceofT
orqueTools
-
7/25/2019 Tohnichi Maintenance of Torque Tools
11/24
Chapter
cReassembling the head part
(1)Apply grease to both pits of the head end part and put a steel ball ineach pit, respectively.
(2)Attach the toggle with the toggle pin to the groove at the end of thehead and then connect the toggle to the thruster. At this time, applyadequate Evertorque lubricant (P.407)to the pin holes.
(3)
Apply Evertorque lubricant to the roller groove of the thruster, andinstall the roller bushing with the roller pin inserted.
(4)Install the head assembly into the tube of part b)by aligning thesquare drive with the at part of the tube(or the side with the serialnumber)and inserting from the thruster side.
(5)Set the tube upright and use the resistance of the table to press thethruster axis part into the hole of the seat.
(6)Insert the head into the tube and insert the head pin by matching it
with the head pin hole and calk it.(7)Confirm that the thruster is in proper contact with the seat by
operating the torque wrench.
7-2. Procedure for Disassembly, Reassembly and Torque Adjustment
Head
Pin, toggle
RollerPin, toggle
Toggle
Thruster
Ball, Steel
Ball, Steel
TECHNICAL DATA
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.796
7-2 Maintenance of Torque Tools
Figure 7-10
-
7/25/2019 Tohnichi Maintenance of Torque Tools
12/24
CTorque Adjustment
Table 7-4. Adjusting tools for QSP3
Torque wrench modelAdjusting tool
Catalog No.Tip shapemm
Hex Bore Depth
QSP25N3 / CSP 931 2.5 1.5 6
QSP50N3 280N3 / CSP 930 4 2.5 8
(1)Insert the adjusting tool (Table 7-4)into the hexagonal hole with pinat the end of the wrench main unit.
(2) Set the torque wrench on a tester, apply loading, and read the torquewhen the toggle operates. Adjust the setting torque by turning theadjusting screw, and repeat several times until the value comes closeto the torque setting that you want to achieve.
(3) Then inspect the set torque value with the tester three times or moreto confrm that the torque value has become stable.
QSP4
Chapter
Technical Data
MaintenanceofT
orqueTools
97
7-2Maintenance of Torque Tools
-
7/25/2019 Tohnichi Maintenance of Torque Tools
13/24
Chapter
Figure 7-11. Detailed illustration for QSP torque adjustment
(3)SP, QSP (6N, 12N, 420N)models
A: Disassembling
B: Reassembling
7-2. Procedure for Disassembly, Reassembly and Torque Adjustment
Thrustring screw
Tightening Torque TThrustring toolTube
ThrustringThrustring screw
Cap
a)Disassembling the head part(1)Pull out the head pin from the tube by removing the calking with a le
orgrinder
and tapping the pin with a punch.(2)Remove the head assembly from the tube. At this time, the toggle,
thruster, and roller, which are connected to the head end part by the
toggle pins, are also removed from the tube.(3) When the two toggle pins linking the head assembly are removed, the
head assembly can be separated into the head, toggle, thruster and
roller.
b)Disassembling the ratchet part
Follow the same procedure as QL model.
c) Disassembling the main spring part
(1)Remove the cap by turning it counterclockwise using the thrustring tool(P.99 Table 7-5).
(2)Loosen the thrustring screw with a hexagon wrench.
(3)Remove the thrustring by turning it counterclockwise with the thrustring
tool.
(4)Pull out the thrustring center, the steel balls, the spring seat, the main
spring and the seat.
a)Reassembling the main spring part(1)Apply Evertorque lubricant (P.407)to the seat on the inside diameter of
the tube and insert the seat.(2)Insert the main spring into the tube.(3)Apply grease to the spring seat, set the specied number of steel balls
and insert the thrustring center. (At this time, keep the tube level and be
careful that the spring does not drop out.)
(4)Assemble the thrustring by turning it clockwise with the thrustring tool.
(5)Tighten the thrustring screw with a hexagon key.
7-2 Maintenance of Torque Tools
98
TECHNICAL DATA
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
14/24
C: Torque Adjustment
Table 7-5. Torque adjustment for SP and QSP models
Torque wrench model name Thrustring tool Thrustring screw Thrustring Cap
SP QSP No. CatalogNo.
Width across
heads
B[mm]
Tightening
Torque
T[Nm]
a1/ d1
[mm]a2/ d2
[mm]
QSP6N / CSP A-1 3101.5 0.5
6.8 / 2 6.8 / 2.2
SP8N,19N QSP12N / CSP A-2 311 9 / 2.5 9 / 3.2
SP38N, 67N A-3 312 2 2.0 12 / 3 12 / 3.2
SP120N 220N A-4 313
3 3.0
16 / 3 16 / 3.2
SP310N A-5 314 18 / 3 18 / 3.2
SP420N560N QSP420N / CSP A-6 315 20 / 3 20 / 3.2
b)Reassembling the head part ((1)-(3) are for QSP only)
(1)Apply grease to both pits of the head end part and put a steelball in each pit, respectively.
(2)Attach the toggle with the toggle pin to the groove at the end ofthe head and then connect the toggle to the thruster. At this time,apply adequate Evertorque lubricant (P.407)to the pin holes.
(3
)Apply Evertorque lubricant to the roller groove of the thruster,and insert the roller bushing with the roller pin inserted.
(4)Install the complete head assembly into the tube from thethruster side.
(5)Set the tube upright and use the resistance of the table topress the thruster axis part into the hole of the seat.
(6)Insert the head into the tube and insert the head pin by matching itwith the head pin hole and calk it.
(7)Confrm that the thruster is in proper contact with the seat byoperating the torque wrench.
(1)Set the wrench on a torque wrench tester, apply loading, andread the torque when the toggle operates. Adjust the settingtorque by turning the thrustring with the thrustring tool, andrepeat several times until the value comes close to the torquesetting you want to achieve.
(2)Then inspect the set torque value with the tester three times ormore to confrm that the torque value has become stable, and
tighten the thrustring screw with the specified torque. (P.99Table 7-5)
(3)Tighten the cap by turning it clockwise using the thrustring tool.
MaintenanceofT
orqueTools
7-2Maintenance of Torque Tools
99
Chapter
Technical Data
-
7/25/2019 Tohnichi Maintenance of Torque Tools
15/24
Chapter
7-2. Procedure for Disassembly, Reassembly and Torque Adjustment(4)DB model
(1)Rotate and remove the back cover with the thrustring tool (P.99
Table
7-5)
(2)
Remove the protector cover. (DB1.5N4 to DB280N)
(3)
Set the notched part of the glass plate so that it is parallel with the
tube.(4)Hold the body in a vice, insert the special tool (P.407)between the
protector and the dial gauge assembly and pry off the glass plate.
(5)Pull off the needle using the special tool.
(6)Take off the scale plate.
(7)Take off the spring plate.
(8)Loosen the two M3 screws with a Phillips screwdriver.
(9)Lift up the dial gauge assembly and take off the sector pin of the
dial gauge assembly from the groove of the dial bar whileconrming using the rear window of the main unit.
Take off the bracket from the protector.
(1)Place the bracket back in the center of the main unit protector.
(2) Insert the dial gauge assembly into the main unit window from
above the bracket. Insert the sector pin into the groove of the dial
bar. (Conrm using the round window on the rear side.)
(3)Apply screw adhesive to the screws of the protector.(4)Match the positions of the dial gauge assembly and the protector
and tighten using the two M3 screws. (tightening torque 0.6 [Nm])
At this time, check the smooth rotation of the bracket.
(5)Attach the spring plate.
(6)Match the center hole of the scale plate with the dial gauge
assembly axis, and assemble while aligning the bracket projections
with the groove on the outside circumference of the scale plate.
(7)Positioning the square drive of the main unit to the left and keepingit facing up, install the needle.
(8)Insert the plate glass, matching it with the center of the bracket.
A: Disassembling the dial gauge
Main bodyCover back
Cover back
Thrustring Tool
B: Reassembling the dial gauge
ProtectorDial gaugeassembly
Main body
Window
Bracket
Dial bar
Dial bar
Sector pin
(10)
7-2 Maintenance of Torque Tools
100
TECHNICAL DATA
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
Figure 7-12
Figure 7-13
-
7/25/2019 Tohnichi Maintenance of Torque Tools
16/24
C: DB Adjustment
Compressed sector
Standard sector
Enlarged sector
Right
Left
(1)Remove the back cover using the thrustring tool. (P.99)
(2)Set the torque wrench in the tester so that a counterclockwise torque
will be applied, and apply preloading. (Tester should carry this out in
RUN mode.)
(3)Release the preloading, and carry out zero adjustment both of the
tester and torque wrench.
(4)Again, set the torque wrench in the tester so that a counterclockwise
torque will be applied, and apply loading up to the torque wrench
maximum specified value. Read the value on the tester. (Tester
should carry this out in RUN mode.)
(5) In the case where there is a discrepancy between the tester value
and the torque wrench indicated value: When the tester value is
lower than the torque wrench indicated value, the sector should be
widened.When the tester value is higher than the torque wrench
indicated value, the sector should be compressed.
(6)Repeat procedures (4)and (5)until the values are within the accuracy
range.
(7)Set the torque wrench in the tester so that a clockwise torque will be
applied, and apply preloading. (Tester should carry this out in RUN
mode.)
(8
)Release the preloading, and carry out zero adjustment both of thetester and torque wrench.
(9)Again, set the torque wrench in the tester so that a clockwise torque
will be applied, and apply loading up to the torque wrench maximum
specified value. Read the value on the tester. (Tester should carry
this out in RUN mode.)
In the case where there is a discrepancy between the tester value and
the torque wrench indicated value: When the tester value is lower
than the torque wrench indicated value, the sector should bewidened.When the tester value is higher than the torque wrench
indicated value, the sector should be compressed.
Repeat procedures (9)and (10) until the values are within the
accuracy range.
Install the back cover to the main unit rear window.
(10)
(11)
(12)
MaintenanceofT
orqueTools
7-2Maintenance of Torque Tools
101
Chapter
Technical Data
Figure 7-14
-
7/25/2019 Tohnichi Maintenance of Torque Tools
17/24
Chapter
7-3. Parts List(1)QL model
7-3 Maintenance of Torque Tools
102
TECHNICAL DATA
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
18/24
No. PART NAME OTYPART No.
QL25N QL50N QL100N4 QL140N4 QL200N4 QL280N
1 HEAD 1 - - - - - -
2 SAW, HEAD 2 02T26243 03T26243 01T48017 05T50449 02T48017 07T50449
3 COVER, HEAD 1 02T03360 03T03360 01T48013 05T50448 02T48013 07T50448
4 CAM 1 02T03361 03T03361 01T48020 04T03361 04T03361 05T50694
5 LEVER, RATCHET 1 02T04762 03T04762 04T04762 05T04762
6 SPRING, RATCHET 2 06T03405 05T03405 01T03405 11T03405 02T03405 12T03405
7 RATCHET, ASSEMBLY 1 00T16061B 00T16061C 00T48012A 00T16061W 00T48012B 00T50507B
8 BALL, STEEL 1 07000051 07000061 07000071
9 SPRING, BALL 1 02T06494 03T06494 04T06494
10 SCREW, FLAT, HEAD 2 02T10312 03T50410 15T50410 05T50410 07T50410
11 TUBE 1 - - - - - -
12 THRUSTER 1 06T12843 05T12843 08T06731 03T12843 02T37240
13 TOGGLE 1 06T50099 05T50099 08T50099 03T50099
14 ROLLER 1 00T35308B 00T35308C 00T35308E 00T35308F
15 PIN, TOGGLE 2 02T37432 03T37432 04T37432 05T37432
16 RING, THRUST 1 05T10339 01T10339 03T10339 03T05034
17 SEAT 1 06T05035 05T05035 04T50122 03T05035
18 GRADUATION, SUP 1 02T50100 00T50102B 00T50104B 00T50106B
19 LOCKER 1 04T50121 03T50121 03T50121
20 SCREW, ADJUSTING 1 05T05031 01T05030 01T12405 01T50659 01T37556
21 SPRING, MAIN 1 09T48019 04T03924 01T48019 09T03924 02T48019 05T37346
22 PLATE, STOP 1 06T04995 05T04995 04T04995 03T04995
23 PIN, HEAD 1 06T05077 05T05077 04T05077 03T05077
24 TUBE, NYLON 1 01T03420 02T03420 03T03420
25 SCREW 1 01003012607 01004015607 01005020607
26 SCREW, THRUST RING 1 04T05188 02T05188 01T05188
27 BALL, STEEL 2 0703 / 321 07001 / 81 07000031 07001 / 81
28 PIN, SPRING 1 050020074 050030084
29 SEAT, SUP, GRADUATION 1 06T09483 05T09483 04T09483 03T09483
30 PIECE, SCALE 1 01T09904 01T09905 01T09906 01T12404 01T50548 01T3755531 PLATE, SCALE 1 01T50365 01T50366 01T50367 01T50368 01T50663 01T50370
32 BALL, STEEL 4 0703 / 321 07000031 07001 / 81
33 WASHER, NYLON 1 02T50320 03T50320 04T50320 05T50320
34 WASHER 1 01T50539 02T50539 03T50539
35 COVER, SCALE 1 01T50538 02T50538 03T50538 04T50538
36 COVER, SUP, GRADUATION 1 01T50267 02T50267 03T50267 04T50267
37 HANDLE 1 01T46004 02T46004 03T46004 04T46004 05T46004
38SEAT, SPRING 2
- - 01T48014 01T45879 01T48015 01T45984
MaintenanceofT
orqueTools
7-3Maintenance of Torque Tools
103
Chapter
Technical Data
-
7/25/2019 Tohnichi Maintenance of Torque Tools
19/24
Chapter
7-3. Parts List2DB model
7-3 Maintenance of Torque Tools
104
TECHNICAL DATA
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
20/24
NO. PART NAME OTY PART No.
DB25N DB50N DB100N DB200N DB280N
1 TUBE ASSEMBLY 1
2 DAL GAUGE ASSEMBLY 1 00T38056A 00T07741A
3 NEEDLE 1 00T12088A
4 PLATE, GLASS 1 01T28398
5 RIVET
1 06002004014 6 COVER, BACK 1 01T08491
7 BALL, STEEL 1 07000051 07000061 07000071
8 SPRING, BALL 1 02T06494 03T06494 04T06494
9 SCREW, FLAT HEAD 2 01003006202
10 BRACKET 1 01T12087
11 COVER, HEAD 1 01T28421 01T50383 01T50384 01T28423 01T28424
12 COVER, PROTECTOR 1 01T50174
13 GRIP 1 01T28410 01T28409 01T28406 01T28407 01T28408
14 PLATE, SCALE 1 01T50193 02T50193 03T50193 04T50193 04T28663
16 SPRING, PLATE 1 03T08172
S
15 S-SINDI, ASSEMBLY 1 00T16065F
Note: Used for "non memory-pointer" model only.
MaintenanceofT
orqueTools
7-3Maintenance of Torque Tools
105
Chapter
Technical Data
-
7/25/2019 Tohnichi Maintenance of Torque Tools
21/24
Chapter
7-4. Cross-section DrawingsHAT
AC
7-4 Maintenance of Torque Tools
106
TECHNICAL DATA
TECHN
ICALDATA
TOHNICHI TORQUE HANDBOOK Vol.7
-
7/25/2019 Tohnichi Maintenance of Torque Tools
22/24
LTDRTD NTDRNTD
FTD2-S
MaintenanceofTorqueTools
7-4Maintenance of Torque Tools
107
Chapter
Technical Data
-
7/25/2019 Tohnichi Maintenance of Torque Tools
23/24
Chapter
7-4. Cross-section DrawingsQL4
MPQL
Chapter
TECHNICAL DATA
TOHNICHI TORQUE HANDBOOK Vol.7
TECHNICALDATA
108
7-4 Maintenance of Torque Tools
-
7/25/2019 Tohnichi Maintenance of Torque Tools
24/24
SP
DB
Chapter
Technical Data 109
MaintenanceofTorqueTools
7-4Maintenance of Torque Tools